SEMICONDUCTOR TECHNICAL DATA Order this document by MOC0/D (20 Volts Peak) The MOC0, MOC02 and MOC0 devices consist of gallium arsenide infrared emitting diodes optically coupled to a monolithic silicon detector performing the function of a Zero Voltage crossing bilateral triac driver. They are designed for use with a triac in the interface of logic systems to equipment powered from Vac lines, such as teletypewriters, CRTs, printers, motors, solenoids and consumer appliances, etc. Simplifies Logic Control of Vac Power Zero Voltage Crossing dv/dt of 2000 V/µs Typical, 000 V/µs Guaranteed To order devices that are tested and marked per VDE 088 requirements, the suffix V must be included at end of part number. VDE 088 is a test option. Recommended for Vac(rms) Applications: Solenoid/Valve Controls Temperature Controls Lighting Controls E.M. Contactors Static Power Switches AC Motor Starters AC Motor Drives Solid State Relays MAXIMUM RATINGS (TA = 2 C unless otherwise noted) INFRARED LED Rating Symbol Value Unit Reverse Voltage VR Volts Forward Current Continuous IF 0 ma Total Power Dissipation @ TA = 2 C Negligible Power in Output Driver Derate above 2 C OUTPUT DRIVER GlobalOptoisolator PD 20. mw mw/ C Off State Output Terminal Voltage VDRM 20 Volts Peak Repetitive Surge Current (PW = 00 µs, 20 pps) Total Power Dissipation @ TA = 2 C Derate above 2 C ITSM A PD 0.7 mw mw/ C [IFT = ma Max] [IFT = 0 ma Max] [IFT = ma Max] *Motorola Preferred Device STYLE PLASTIC STANDARD THRU HOLE CASE 70A 0 COUPLER SCHEMATIC 2 ZERO CROSSING CIRCUIT. ANODE 2. CATHODE. NC. MAIN TERMINAL. SUBSTRATE. DO NOT CONNECT. MAIN TERMINAL TOTAL DEVICE Isolation Surge Voltage() (Peak ac Voltage, 0 Hz, Second Duration) Total Power Dissipation @ TA = 2 C Derate above 2 C VISO 700 Vac(pk) PD 20 2.9 mw mw/ C Junction Temperature Range TJ 0 to +00 C Ambient Operating Temperature Range(2) TA 0 to +8 C Storage Temperature Range(2) Tstg 0 to +0 C Soldering Temperature (0 s) TL 20 C. Isolation surge voltage, VISO, is an internal device dielectric breakdown rating.. For this test, Pins and 2 are common, and Pins, and are common. 2. Refer to Quality and Reliability Section in Opto Data Book for information on test conditions. Preferred devices are Motorola recommended choices for future use and best overall value. GlobalOptoisolator is a trademark of Motorola, Inc. (Replaces MOC00/D) Motorola, Inc. Optoelectronics 99 Device Data
I ELECTRICAL CHARACTERISTICS (TA = 2 C unless otherwise noted) INPUT LED Reverse Leakage Current (VR = V) Characteristic Symbol Min Typ Max Unit IR 0.0 00 µa Forward Voltage (IF = 0 ma) OUTPUT DETECTOR (IF = 0 unless otherwise noted) Leakage with LED Off, Either Direction (Rated VDRM () ) Peak On State Voltage, Either Direction (ITM = 00 ma Peak) VF.. Volts IDRM 0 00 na VTM.8 Volts Critical Rate of Rise of Off State Voltage dv/dt 000 2000 V/µs COUPLED LED Trigger Current, Current Required to Latch Output (Main Terminal Voltage = V(2)) MOC0 MOC02 MOC0 Holding Current, Either Direction IH 20 µa Isolation Voltage (f = 0 Hz, t = sec) VISO 700 Vac(pk) IFT 0 ma ZERO CROSSING Inhibit Voltage (IF = Rated IFT, MT MT2 Voltage above which device will not trigger.) Leakage in Inhibited State (IF = Rated IFT, Rated VDRM, Off State) VIH 20 Volts IDRM2 00 µa. Test voltage must be applied within dv/dt rating. 2. All devices are guaranteed to trigger at an IF value less than or equal to max IFT. Therefore, recommended operating IF lies between max 2. IFT ( ma for MOC0, 0 ma for MOC02, ma for MOC0) and absolute max IF (0 ma). TYPICAL ELECTRICAL CHARACTERISTICS TA = 2 C TM, ON-STATE CURRENT (ma) +800 +00 +00 +200 0 200 00 00 800 OUTPUT PULSE WIDTH 80 µs IF = 0 ma f = 0 Hz TA = 2 C NORMALIZED IFT..2. 0.9 0.8 0.7 NORMALIZED TO TA = 2 C 2 0 2 VTM, ON STATE VOLTAGE (VOLTS) 0 20 0 20 0 0 80 TA, AMBIENT TEMPERATURE ( C) 00 Figure. On State Characteristics Figure 2. Trigger Current versus Temperature 2 Motorola Optoelectronics Device Data
I I 00. DRM, PEAK BLOCKING CURRENT (na) 200 00 0 20 0 0 IF = 0 20 0 20 0 0 80 00 TA, AMBIENT TEMPERATURE ( C) DRM2, NORMALIZED...2. 0.9 0.8 0.7 0. 0 IF = RATED IFT 20 0 20 0 0 80 00 TA, AMBIENT TEMPERATURE ( C) Figure. IDRM, Peak Blocking Current versus Temperature Figure. IDRM2, Leakage in Inhibit State versus Temperature I FT, NORMALIZED LED TRIGGER CURRENT 2 20 0 0 NORMALIZED TO: PWin 00 µs TA = 2 C 2 0 20 0 PWin, LED TRIGGER WIDTH (µs) Figure. LED Current Required to Trigger versus LED Pulse Width 00 +20 Vdc PULSE INPUT MERCURY WETTED RELAY RTEST CTEST D.U.T. R = 0 kω X00 SCOPE PROBE. The mercury wetted relay provides a high speed repeated pulse to the D.U.T. 2. 00x scope probes are used, to allow high speeds and voltages.. The worst case condition for static dv/dt is established by triggering the D.U.T. with a normal LED input current, then removing the current. The variable RTEST allows the dv/dt to be gradually increased until the D.U.T. continues to trigger in response to the applied voltage pulse, even after the LED current has been removed. The dv/dt is then decreased until the D.U.T. stops triggering. RC is measured at this point and recorded. APPLIED VOLTAGE WAVEFORM 8 V Vmax = 20 V 0 VOLTS dv dt 0. V max RC 8 RC RC Figure. Static dv/dt Test Circuit Motorola Optoelectronics Device Data
VCC Rin 2 MOC0/ 02/0 k 80 Ω 9 0.0 LOAD HOT VAC NEUTRAL * For highly inductive loads (power factor < 0.), change this value to 0 ohms. Typical circuit for use when hot line switching is required. In this circuit the hot side of the line is switched and the load connected to the cold or neutral side. The load may be connected to either the neutral or hot line. Rin is calculated so that IF is equal to the rated IFT of the part, ma for the MOC0, 0 ma for the MOC02, or ma for the MOC0. The 9 ohm resistor and 0.0 µf capacitor are for snubbing of the triac and may or may not be necessary depending upon the particular triac and load used. Figure 7. Hot Line Switching Application Circuit VAC VCC Rin 2 MOC0/ 02/0 R D 80 Ω SCR SCR Suggested method of firing two, back to back SCR s, with a Motorola triac driver. Diodes can be N00; resistors, R and R2, are optional k ohm. NOTE: This optoisolator should not be used to drive a load directly. It is intended to be a trigger device only. R2 D2 LOAD Figure 8. Inverse Parallel SCR Driver Circuit Motorola Optoelectronics Device Data
PACKAGE DIMENSIONS A B NOTES:. DIMENSIONING AND TOLERANCING PER ANSI Y.M, 982. 2. CONTROLLING DIMENSION: INCH.. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. T SEATING PLANE F PL E PL N C L K G M D PL 0. (0.00) M T A M B M J PL 0. (0.00) M T B M A M INCHES MILLIMETERS DIM MIN MAX MIN MAX A 0.20 0.0 8. 8.89 B 0.20 0.20.0.0 C 0. 0.200 2.9.08 D 0.0 0.020 0. 0.0 E 0.00 0.070.02.77 F 0.00 0.0 0.2 0. G 0.00 BSC 2. BSC J 0.008 0.02 0.2 0.0 K 0.00 0.0 2..8 L 0.00 BSC 7.2 BSC M 0 0 N 0.0 0.00 0.8 2. STYLE : PIN. ANODE 2. CATHODE. NC. MAIN TERMINAL. SUBSTRATE. MAIN TERMINAL CASE 70A 0 ISSUE G A B NOTES:. DIMENSIONING AND TOLERANCING PER ANSI Y.M, 982. 2. CONTROLLING DIMENSION: INCH. F PL E PL G H D PL C L K PL 0. (0.00) M T A M B M J T SEATING PLANE 0. (0.00) M T B M A M CASE 70C 0 ISSUE D INCHES MILLIMETERS DIM MIN MAX MIN MAX A 0.20 0.0 8. 8.89 B 0.20 0.20.0.0 C 0. 0.200 2.9.08 D 0.0 0.020 0. 0.0 E 0.00 0.070.02.77 F 0.00 0.0 0.2 0. G 0.00 BSC 2. BSC H 0.020 0.02 0. 0. J 0.008 0.02 0.20 0.0 K 0.00 0.0 0. 0.88 L 0.20 BSC 8. BSC S 0.2 0.90 8. 9.90 *Consult factory for leadform option availability Motorola Optoelectronics Device Data
F PL T SEATING PLANE A B N L C G K D PL J NOTES:. DIMENSIONING AND TOLERANCING PER ANSI Y.M, 982. 2. CONTROLLING DIMENSION: INCH.. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. INCHES MILLIMETERS DIM MIN MAX MIN MAX A 0.20 0.0 8. 8.89 B 0.20 0.20.0.0 C 0. 0.200 2.9.08 D 0.0 0.020 0. 0.0 E 0.00 0.070.02.77 F 0.00 0.0 0.2 0. G 0.00 BSC 2. BSC J 0.008 0.02 0.2 0.0 K 0.00 0.0 2..8 L 0.00 0.2 0. 0.80 N 0.0 0.00 0.8.02 E PL 0. (0.00) M T A M B M *Consult factory for leadform option availability CASE 70D 0 ISSUE D Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Typical parameters can and do vary in different applications. All operating parameters, including Typicals must be validated for each customer application by customer s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.; Tatsumi SPD JLDC, Toshikatsu Otsuki, P.O. Box 2092; Phoenix, Arizona 80. 800 27 F Seibu Butsuryu Center, 2 Tatsumi Koto Ku, Tokyo, Japan. 0 2 8 MFAX: RMFAX0@email.sps.mot.com TOUCHTONE (02) 2 09 HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, INTERNET: http://design NET.com Ting Kok Road, Tai Po, N.T., Hong Kong. 82 229298 Motorola Optoelectronics MOC0/D Device Data