Air Cylinder. Series NCA1 NFPA Interchangeable

N4- ir ylinder Series N N Interchangeable Medium uty.5 to 4 ore ifferent N Mounting Options Non-otating Option Tandem ylinder Option uto Switch apable

ir ylinder N Interchangable Series N Improved cushion capacity loating cushion seal design eliminates piston rod bouncing due to cracking pressure at beginning of stroke. ompact and lightweight design The square covers are made of an aluminum die casting and provide a lower cost, lighter weight product.

Increased kinetic energy absorption The absorption of kinetic energy had been increase by nearly % through increase cushion volume and the use of a new cushion seal. ø.5, ø, ø.5, ø.5, ø4 ull port design llows for improved piston breakaway. ull range of N interchangable mounting configurations Mounting imensions are in accordance with NSI (N) T.6.7-996, luid ower Systems and roducts - Square Head Industrial ylinders - Mounting imensions.

Table of ontents How to Order....... 5 Specifications..... 6 onstruction / art List / Seal Kit...... 7 asic Mounting..... 8 oot Mounting....... 8 ront lange Mounting...... 9 ear lange Mounting........ 9 Side Tapped Mounting........ ouble etachable ear levis Mounting....... enter Trunnion Mounting....... Single etachable ear levis Mounting....... ouble ear levis Mounting....... Side Lug Mounting....... od Trunnion Mounting....... Head Trunnion Mounting....... ouble od.............. 4 to 6 Non-otating od and ouble od Non-otating......... 7 to 4 Stainless Steel od (X6) Low Speed (X9). 5 High Temperature (X6) / Low Temperature (X7)... 6 Special Trunnion Location (X46US). 7 & 8 Oversized od with Special Trunnion Location (X5 - X46US). 9 Stainless Steel Tie ods / Tie od Nuts (XUS) od oot..... Oversized od / Standard od and Non-otating (X5 / X9US).. to 6 djustable Stroke xtended (X8)... 7 djustable Stroke eturn (X9). 8 ual Operation ouble od (X).. 9 ual Operation Single od (X)... 4 Special od nd Modifications........ 4 ccessories.......... 4 uto Switch Options........... 4 to 5 recautions.......... 5 to 58 4

Medium uty ir ylinder Series N How To Order N 5 4 5 X5 uto Switch Nil Standard With uto Switch (Magnetic iston) Model Nil K W M Standard ylinder Non-otating ylinder ouble od Male od Stud Mounting MX asic L MS oot M ront lange M ear lange MS4 Side Tapped M ouble etachable ear levis T MT4 enter Trunnion M4 Single etachable ear levis X M ouble ear levis S MS Side Lug U MT od Trunnion MT Head Trunnion Mounting racket art Numbers ore Size 5.5" " 5.5" 5.5" 4 4" or larger bore size up to " bore. lease consult T: N4-X. Standard Stroke Inches Stroke Hundredths of an Inch Options X5 Oversized od X6 High Temperature X7 Low Temperature X9 Low Speed X6 Stainless Steel iston od X8 djustable Stroke xtended X9 djustable Stroke eturn X ual Operation/ouble od X ual Operation/Single od X Viton Seals X5 With oil Scraper X46US Special Trunnion Location X9US Non-otating Oversize od Stainless Steel iston od, XUS Tie od, Tie od Nut, ushion Valve Needle or special rod end modifications please see page 4. No. of Switches Nil ieces S iece n "n" ieces See uto Switch Options pages od oot Nil Without oot Nylon oot K Neoprene oot ir ushion Nil oth nds N None H Head nd od nd Mounting racket ore 5 (.5") (") art Number 5 (.5") 5 (.5") 4 (4") oot N-L5 N-L N-L5 N-L5 N-L4 lange N-5 N N-5 N-5 N-4 ouble levis (M) N-5 N- N-5 N-5 N-4 Single levis N-5 N- N5 N-5 N-4 Side Lug N-S5 N-S N-S5 N-S5 N-S4 ouble levis (M) N-X5 N-X N-X5 N-X5 N-X4 These Kits are for Standard Single od/ouble cting ylinders without Options. or Option Kits, please contact your local SM sales office. One Kit required per cylinder. The SM N expanded series N Industrial Interchangeable neumatic ylinders are now available in bore sizes ranging from 5 to 8 Medium uty, and.5 to 4 Heavy uty. The N xpanded Series ylinders offer: eplaceable od land full range of N interchangeable mounting configurations vailable in three construction types: luminum, Steel, and Stainless Steel omposite fiber tube optional ully adjustable cushion or further information, please consult your local SM sales office. 5

Series N Medium uty ir ylinder Specifications Type Standard luid ir Lubrication Non-lube Max. Operating ressure 5psi (.75Ma) Min. Operating ressure 8 psi (.6Ma) mbient and luid Temp. 4 to 4 (5 to 6 ) to in/s iston Speed (5 to 5mm/s) asic, oot ront and ear lange Mounting Side Tapped, levis enter Trunnion, Side Lug od and Head Trunnion Non-otating ccuracy n/a ouble od ir Non-lube 5 psi (.75Ma) 8 psi (.6Ma) 4 to 4 (5 to 6 ) to in/s (5 to 5mm/s) asic, oot lange Side Tapped enter and od Trunnion n/a Non-otating od ir Non-lube 5 psi (.75Mpa) 5 psi (.Ma) 4 to 4 (5 to 6 ) to in/s (5 to 5mm/s) asic, oot ront and ear lange Side Tapped, levis enter Trunnion, Side Lug od and Head Trunnion ±.5 od and head trunnion maximum operating pressure for 5 and 4 bore is up to 5 psi Standard Strokes ore Size Standard Stroke Maximum Stroke.5,,, 4, 5, 6, 8,,, 4, 6, 8,,4,.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4 onsult SM.5, 4,,, 4, 5, 6, 8,,, 4, 6, 8,, 4, 8, ase Material / Surface Treatment escription Material Note over luminum alloy Silver paint Tube luminum alloy Hard alumite Seals Nitrile rubber L, L iston od arbon steel Hard chromate iston luminum alloy Hard alumite Weight / luminum Tube asic Weight dditional weight per stroke (lbs) ore Inch 5 (.5 ) ( ) 5 (.5 ) 5 (.5 ) 4 (4 ) asic type.58.5.9 6. 7.79 oot mounting.95.86.8 7.45. lange mounting.. 4.4 8.85.66 levis mounting.7. 4.8 8.95.4 Trunnion mounting.79.8 5.5.5.5 or all mountings.8.48.5.97.6 6 ylinder ores and orces: ush Stroke ore iston rea orces (lbs); ush Stroke Operating Medium ressure (psi) 5 6 8 5.5.767 88 6 4 77 5 44.4 57 88 5 4 68 785.5 4.99 45 95 9 49 98 7.5 8.96 45 498 664 8 659 74 4.566 68 754 5 57 5 4 ylinder ores and orces: ull Stroke iston iston orces (lbs); ull Stroke (educt the listed thrusts corresponding od od to the rod size from push stroke pressure) iameter rea Operating Medium ressure (psi) 5 6 8 5.65.7 5 8 5 6 77.785 9 47 6 79 57 96.75.485 74 89 9 48 97 7 To calculate thrust forces not shown in the table, multiply operating pressure by piston area. How to use this table q Locate column with desired operating pressure. w Move down that column and locate the thrust value which is equal (or the next larger to the force to be delivered by the cylinder). e On that same line, locate in the first (left) column the bore size recommended for your application. Note: These are guide lines only, which must be substantiated using additional data specific to your application. To calculate pull forces not shown in the table, use the following formula: ull orce = (iston rea-od rea) x Working ressure How to use this table q To find the force on the pull stroke, locate the required piston rod diameter in the left most column. w Moving to the right, locate the required working pressure. e educt the value shown at the intersection from the push stroke force value determined from the ush Stroke table. The resultant is the available pull stroke table.

Medium uty ir ylinder Series N onstruction / arts List 8 6 4 7 7 4 5 5 8 9 6 arts List No. escription od over Head over ylinder Tube 4 iston od 5 iston 6 ushion Sphere 7 od ushing 8 ushion Valve 9 Tie od Tie od Nut etaining ing od Seal etainer * ushion Seal 4* od Seal 5* iston Seal 6* ushion Valve Seal 7* ylinder Tube asket 8 iston asket 9 Wear ing am Nut *omponents include in a seal kit. Material luminum alloy luminum alloy luminum alloy arbon steel luminum alloy luminum alloy ronze casting arbon steel arbon steel arbon steel arbon steel esin N N N N N N esin arbon steel How To Order Seal Kits N W 5 - S - 9 5 N5-Q68-S N5--Q68-S N-Q69-S N--Q69-S 5 N5-Q6-S N5--Q6-S 5 N5-Q6-S N5--Q6-S 4 N4-Q6-S N4--Q6-S lease see below for How to Order ylinder Tube. vailable only as an ssembled Item. lease see below for How to Order iston od ssembly. vailable only as an ssembled Item. lease see below for How to Order iston od ssembly. vailable only as an ssembled Item. lease see below for How to Order iston od ssembly. vailable only as an ssembly Item. lease see od/head over. N5--4 N5--5 lease see below for How to Order Tie od. N5--Q68 N--Q69 58-9 N5--Q6 58- N5--Q6 N5--Q68 N5--Q68 N5--Q68 N5--Q6 N5--Q6 vailable only as an ssembled Item. lease see below for How to Order Seal Kit. vailable only as an ssembled Item. lease see below for How to Order Seal Kit. vailable only as an ssembled Item. lease see below for How to Order Seal Kit. vailable only as an ssembled Item. lease see below for How to Order Seal Kit. vailable only as an ssembled Item. lease see below for How to Order Seal Kit. vailable only as an ssembled Item. lease see below for How to Order iston od ssembly. vailable only as an ssembled Item. lease see below for How to Order iston od ssembly. M-45 M-45 M-45 M- How To Order iston od ssembly ouble cting Single od N 5-6 - 4 M- Option Nil Single rod W ouble rod K* Non-rotating ore 5 5 5 4 * available for 5, and 5 bores only ** use single rod designation when ordering X kit Note: X seal kit order single rod kits *** not available with K option How To Order ylinder Tube ouble cting Single od N 5-4 - 4 ore 5 5 5 4 Special Options X5*** Over sized rod X6*** High temperature X7*** Low temperature X56*** Oversized w/ high temperature* X ual Operation/Single od** Stroke (In Inches and Hundredths of Inches) ore 5 5 5 4 How To Order Tie ods N 5 - - 759-4 pplicable ore Tie od Size ore 5 5 759 76 5 76 5 5 76 4 5 76 Stroke (In Inches and Hundredths of Inches) Stroke (In Inches and Hundredths of Inches) Note: Quantity is one piece. Not applicable for types: ouble rod (W), Trunnion (T), X8, X9, X, X, Over sized rod (X5) with front mounts. lease consult your local SM sales office. 7

Series N Medium uty ir ylinder asic Mounting Type N (MX Mounting Style) Z + Stroke ø - (NT) cross ore 5 (.5") (") 5 (.5") 5 (.5") 4 (4") MM..6..9 4.7 / / / / / / 9/6 9/6 9/6 /4-8 5/6-4 5/6-4 -4-4 / 4 /.. / /.6.6..57.57..6.6.8.8.4.84.9.76. oot Mounting Type N L (MS Mounting Style) Z + Stroke X + Stroke ø cross - (NT) H T 7/6-7/6-7/6- -6-6.7.7.75.4.4 L 4 /4 4 /4.6.4.48.7.7 Z 4 4 4 5 5/64 5 5/64 6- (Hole) S O L S + Stroke L O ore 5 (.5") (") 5 (.5") 5 (.5") 4 (4") MM 7/6-7/6-7/6-..6. -6-6.9 4.7 / / /6 H /6 /6 7/6 L /8 9/6 /8 9/6 5/6-4 /6 5/6 /4 O 7/6 9/6 T /8 /8 9/6 /4-8. 9/6 5/6-4 /. /64 / / / -4 4 / /4 /4 5/64 / / / -4 4 / / /.6..6.6..6.57.8.57.8 S.4 /4.7.6.84.7.4.9 /4.75.48.76.4.7. /.4.7 L S X Z 6 5 6 /6 6 5 6 /6 6 /8 5 6 5/6 4 /4 7 6 7 4/4 7 6 7 8

Medium uty ir ylinder Series N ront lange Mounting Type N (M Mounting Style) ø 4- (Hole) cross - (NT) W T U Z + Stroke ore MM 5 (.5") (") 5 (.5") 5 (.5") 4 (4") 7/6-7/6-7/6- -6-6..6..9 4.7 / / / / / / 9/6 9/6 9/6 /4-8 5/6-4 5/6-4 -4-4 / 4 /.. / / 5/6.6..6.6..6 7/6.57.8 7/6.57.8.4.84.9.76. T 4 /6 5 7/6 U 4 /8 4 5 / 6 /4 W.7.7.75.4.4 L 4 /4 4 /4.6.4.48.7.7 Z 4 4 4 5 5/64 5 5/64 ear lange Mounting Type N (M Mounting Style) -cross - (NT) 4- (Hole) ø T X + Stroke U Z + Stroke ore 5 (.5") (") 5 (.5") 5 (.5") 4 (4") MM 7/6-7/6-7/6- -6-6..6..9 4.7 / / / / / / 9/6 9/6 9/6 /4-8 5/6-4 5/6-4 -4-4 / 4 /.. / / 5/6 7/6 7/6.6.6..57.57..6.6.8.8.4.84.9.76. T 4 /6 5 7/6 U 4 /8 4 5 / 6 /4.7.7.75.4.4.6.4.48.7.7 X 4 4 4 5 5 Z 5 5 5 /8 6 /4 6 /4 9

Series N Medium uty ir ylinder Side Tapped Mounting Type N (MS4 Mounting Style) ø cross - (NT) / TN 4-NT N eep XT SN + Stroke Z + Stroke ore 5 (.5") (") 5 (.5") 5 (.5") 4 (4") MM 7/6-. 7/6-7/6- -6-6.6..9 4.7 / / / / / / 9/6 9/6 9/6 /4-8 5/6-4 5/6-4 -4-4 / 4 / / /4 / /4.. / /.6.6..57.57..6.6.8.8 N 9/ 7/6 9/ NT /4-5/6-8 -6 /- /-.4.84.9.76. TN /4 / /6 XT 5/6 5/6 5/6 7/6 7/6.7.7.75.4.4 L 4 /4 4 /4.6.4.48.7.7 SN /4 /4 Z 4 4 4 5 5/64 5 5/64 ouble etachable ear levis Mounting Type N (M Mounting Style) cross - (NT) L ø W W ø L X + Stroke M Z + Stroke ore 5 (.5") (") 5 (.5") 5 (.5") 4 (4") MM 7/6-7/6-7/6- -6-6..6..9 4.7 / / / / /4 /4 / / / W / / / 9/6 9/6 9/6 /4-8 5/6-4 5/6-4 -4-4 / 4 /.. / /.6.6..57.57..6.6.8.8 L /4 /4 L M / / /.4.84.9.76. X 5 5 5 7 / 7 /.7.7.75.4.4 L 4 /4 4 /4.6.4.48.7.7 Z 6 /4 6 /4 6 8 /4 8 /4

Medium uty ir ylinder Series N enter Trunnion Mounting Type N T (MT4 Mounting Style) XI + / Stroke 4- -cross - (NT) ø. UV ø. + -.. TM. TT Z + Stroke UM ore MM TM TT UM UV L XI Z 5 (.5") 7/6-. 9/6 /4-8..6..4.5.8 4.5.7.6.89 4 (") 7/6-.6 9/6 5/6-4 /..6.6.84.8 5.56.7.4.9 4 5 (.5") 7/6-. 9/6 5/6-4..6.9.5.8 5.5.9.75.48.99 4 5 (.5") -6.9 / / / -4 /.57.8.76 4.5.4 6.5 4..4.7 4 /4.7 5 5/64 4 (4") -6 4.7 / / / -4 4 / /.57.8. 5.5.57 7.5 5..4.7 4 /4.74 5 5/64 Single etachable ear levis Mounting Type N (M4 Mounting Style) -cross - (NT) ø ø L X + Stroke M Z + Stroke ore MM L M X L Z 5 (.5") 7/6-. / 9/6 /4-8..6..6.4 5.7.6 6 (") 7/6-.6 / 9/6 5/6-4 /..6.6.6.84 5.7.4 6 5 (.5") 7/6-. / 9/6 5/6-4..6.6.9 5.75.48 6 / 5 (.5") -6.9 / / /4-4 /.57.8 /4.87.76 7 /.4 4 /4.7 8 4 (4") -6 4.7 / / /4-4 4 / /.57.8 /4.87. 7 /.4 4 /4.7 8

Series N Medium uty ir ylinder ouble ear levis Mounting Type N X (M Mounting Style) S.H..S. cross - (NT) W W L ø Z + Stroke L X + Stroke M ore MM W L L M X L Z 5 (.5") 7/6-. / / 9/6 /4-8..6..6.75.4.6 5.7.6 4.75 (") 7/6-.6 / / 9/6 5/6-4 /..6.6.6.75.84.6 5.7.4 4.75 5 (.5") 7/6-. / / 9/6 5/6-4..6.6.75.9.6 5 /.75.48 4.88 5 (.5") -6.9 / / /4-4 /.57.8.5.5.76.87 6.4 4 /4.7 5.8 4 (4") -6 4.7 / / /4-4 4 / /.57.8.5.5..87 6.4 4 /4.7 5.8 Note: Mounting dimensions are the same as N (M) except where marked. ( ) Side Lug Mounting Type N S (MS Mounting Style) Z + Stroke cross - (NT) øs Screw (4) Hole ST / TS SW SW US XS SU SU SS + Stroke S ore MM L S SS ST SU SW S TS US XS Z 5 (.5") 7/6-9/6 /4-8..6..6.6.4.88.94.94.75.5.8.7 5.9 (") 7/6-9/6 5/6-4 /..6.6.6.4.84.88.94.94.5 4.8.7 5.9 5 (.5") 7/6-9/6 5/6-4..6.75.48.9.94.94.75 4.5.8.75 5. 5 (.5") -6 / / -4 /.57.8 4.5.7.76 /.5.5 /.5 4.75 5.75.88.4 6.8 4 (4") -6 / / -4 4 / /.57.8 4.5.7. /.5.5 /.5 5.5 6.5.88.4 6.8

Medium uty ir ylinder Series N od Trunnion Mounting Type N U (MT Mounting Style) ø 4- cross -(NT) Head Trunnion Mounting Type N (MT Mounting Style) cross - (NT) ø 4- ø. + -. ø. -. ir ushion djustable.. Z + Stroke ore MM L Z 5 (.5") 7/6-. 9/6 /4-8..6..4.7.6 4.75 (") 7/6-.6 9/6 5/6-4 /..6.6.84.7.4 4.75 5 (.5") 7/6-. 9/6 5/6-4..6.9.75.48 4.88 5 (.5") -6.9 / / / -4 /.57.8.76.4 4 /4.7 5.8 4 (4") -6 4.7 / / / -4 4 / /.57.8..4 4 /4.7 5.8 ir ushion djustable.. Z + Stroke ore MM L Z 5 (.5") 7/6-. 9/6 /4-8..6..4.7.75.6 4.75 (") 7/6-.6 9/6 5/6-4 /..6.9.84.7.75.4 4.75 5 (.5") 7/6-. 9/6 5/6-4..9.9.75.88.48 4.88 5 (.5") -6.9 / / -4 /.57.8.76.4 4.45.7 5.8 4 (4") -6 4.7 / / -4 4 / /.57.8..4 4.45.7 5.8

Series N Medium uty ir ylinder Specifications ore size (inch).5.5.5 4 Media ir Max. Operating ressure Min. Operating ressure mbient and Media Temperature iston Speed ushion Mounting Types 5 psi (7.5 kgf/cm²) 8 psi (.5 kgf/cm²) 4 to 4 (5 to 6 ) to inch/sec (5 to 5mm/sec) ir ushion Standard asic, oot, lange, enter Trunnion, od Trunnion Standard with air cushion uto-switch mounting available Standard Stroke List ore size Standard Stroke.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4,.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4.5, 4,,, 4, 5, 6, 8,,, 4, 6, 8,, 4, 8, How To Order N W MOUNTIN O STOK SUIX x: NW 5-4 uto-switch capable ouble od ouble od asic Mounting Type N W cross - (NT) + Stroke cross ø L + Stroke K + Stroke ZM + x Stroke XT S + Stroke XT + Stroke ore 5 (.5") (") 5 (.5") 5 (.5") 4 (4") MM 7/6-7/6-7/6- -6-6..6..9 4.7 / / / / 9/6 9/6 9/6 /4-8 5/6-4 5/6-4 -4-4 / 4 /.. / /.6.6..57.57 K.8.4.4.4.4 L.78.8.98 4.64 4.64.6.4.48.7.7.4.84.9.76..7.7.75.4.4 ZM 5.78 5.8 5.98 7.4 7.4 XT 5/6 5/6 5/6 7/6 7/6 S.9.94..5.5 4

Medium uty ir ylinder Series N ouble od oot Mounting Type N WL ø -cross ZM + x Stroke - (NT) + Stroke + Stroke H T -cross S 6- (Hole) K O L L + Stroke L O SL + Stroke ore 5 (.5") (") 5 (.5") 5 (.5") 4 (4") MM 7/6-7/6-7/6- -6-6..6..9 4.7 / / /6 /6 /8 /6 4 / H /6 7/6 5/6 /4 L /4 /4 O 7/6 9/6 9/6 T /8 /8 /8 /64 5/64 / / / / 9/6 9/6 9/6 /4-8 5/6-4 5/6-4 -4-4 / 4 /.. / /.6.6..57.57 K.4.47.47.59.65 S /4 /4 /.7.7.75.4.4.6.4.48.7.7.4.84.9.76. L.78.8.98 4.64 4.64 SL 5.78 5.8 5.98 7.4 7.4 ZM 5.78 5.8 5.98 7.4 7.4 ouble od ront lange Mounting Type N ø 4-ø (Hole) -cross - (NT) + Stroke -cross T U W L + Stroke ZM + x (Stroke) K + Stroke ore 5 (.5") (") 5 (.5") 5 (.5") 4 (4") MM 7/6-7/6-7/6- -6-6..6..9 4.7 / / / / 9/6 9/6 9/6 /4-8 5/6-4 5/6-4 -4-4 / 4 /.. / / 5/6 7/6 7/6.6.6..57.57 K.8.4.4.4.4.4.84.9.76. T 4 /6 5 7/6 U 4 /8 4 5 / 6 /4 W.7.7.75.4.4 L.78.8.98 4.64 4.64.6.4.48.7.7 ZM 5.78 5.8 5.98 7.4 7.4 5

Series N Medium uty ir ylinder ouble od enter Trunnion Mounting Type N WT UM ø cross XI + / Stroke - (NT) + Stroke cross UV ø. -.. TM.. TT L + Stroke ZM + x Stroke K + Stroke ore 5 (.5") (") 5 (.5") 5 (.5") 4 (4") MM 7/6-7/6-7/6- -6-6..6..9 4.7 / / / / 9/6 9/6 9/6 /4-8 5/6-4 5/6-4 -6-6 / 4 /.. / /.6.6..57.57 K.8.4.4.4.4.4.84.9.76. TM.5.5 4.5 5.5 TT.8.8.8.4.57 UM 4.5 5 5.5 6.5 7.5 UV.56.9 4. 5..7.7.75.4.4.6.4.48.7.7 L.78.8.98 4.64 4.64 XI.89.9.99.7.74 ZM 5.78 5.8 5.98 7.4 7.4 ouble od od Trunnion Mounting Type N WU ø cross - (NT) + Stroke -cross ø. -... ir ushion djustable L + Stroke ZM + x Stroke K + Stroke ore 5 (.5") (") 5 (.5") 5 (.5") 4 (4") MM 7/6-7/6-7/6- -6-6..6..9 4.7 / / / / 9/6 9/6 9/6 /4-8 5/6-4 5/6-4 -4-4 / 4 /.. / /.6.6..57.57 K.8.4.4.4.4.4.84.9.76..7.7.75.4.4 L.78.8.98 4.64 4.64.6.4.48.7.7 ZM 5.78 5.8 5.98 7.4 7.4 6

Medium uty ir ylinder Series N Specifications ore size (inch).5.5 Media Max. Operating ressure Min. Operating ressure mbient and Media Temperature iston Speed ushion otation Torque ange Non-otating od ccuracy Mounting Types ir 5 psi (7.5 kgf/cm ) 5 psi (.5 kgf/cm ) 4 to 4 (5 to 6 ) to inch/sec (5 to 5mm/sec) ir ushion Standard.9 Lbs. in or less ±.5 asic, oot, lange, Side Tapped enter Trunnion, ear levis, Side Lug Non-rotating rod accuracy: ±.5 uto switch mounting available Standard Stroke List ore size Standard Stroke.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4,.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4 How To Order N K MOUNTIN O STOK SUIX uto-switch capable x: NK5-4 Non-otating od asic Mounting Type N K - (NT) ø ø.6 -cross TN 4-NT N eep XT SN + Stroke Z + Stroke ore 5 (.5") (") 5 (.5") 7/6-7/6-7/6-..6..55.55.55 /4-8 5/6-4 5/6-4 /...6.6...6.6 N 9/ 7/6 9/ NT /4-5/6-8 -6.4.84.9.7.7.75 L.6.4.48 Z TN 4 4 4 /4 XT 5/6 5/6 5/6 SN /4 /4 7

Series N Medium uty ir ylinder Non-otating od oot Mounting Type N KL Z + Stroke X + Stroke - (NT) ø T H ø.6 -cross S 6- (Hole) O L L O S + Stroke ore 5 (.5") (") 5 (.5") 7/6-7/6-7/6-..6. /6 /6 /8 H /6 7/6 L O 7/6 9/6 9/6 T /8 /8 /8.55 /4-8..55 5/6-4.5..55 5/6-4..6.6.4.84.9 S /4 /4.7.7.75.6.4.48 L S 6 6 6 /8 X 5 5 5 Z 6.6 6.87 6. Non-otating od ront lange Mounting Type N K ø 4-ø (Hole) W - (NT) ø.6 cross T U Z + Stroke ore 5 (.5") (") 5 (.5") 7/6-7/6-7/6-..6..55.55.55 /4-8 5/6-4 5/6-4 /.. 5/6.6.6...6.6.4.84.9 T U 4 /8 4 W.7.7.75 L.6.4.48 Z 4 4 4 8

Medium uty ir ylinder Series N Non-otating od ear lange Mounting Type N K - (NT) ø 4-ø (Hole) cross Non-otating od ouble etachable ear levis Mounting Type N K - (NT) ø ø ø.6 ø.6 X + Stroke T Z + Stroke U ore T U X Z 5 (.5") 7/6-..55 /4-8. 5/6.6..4.7.6 4 5 (") 7/6-.6.55 5/6-4 /..6.6.84 4 /8.7.4 4 5 5 (.5") 7/6-..55 5/6-4..6.9 4.75.48 4 5 /8 cross L L M W W X + Stroke Z + Stroke ore W L L M X L Z 5 (.5") 7/6-. / /.55 /4-8..6. /.4 5.7.6 6 /4 (") 7/6-.6 / /.55 5/6-4 /..6.6 /.84 5.7.4 6 /4 5 (.5") 7/6-. / /.55 5/6-4..6 /.9 5.75.48 6 9

Series N Medium uty ir ylinder Non-otating od enter Trunnion Mounting Type N KT ø UM -cross XI + / Stroke - (NT). UV ø. -. ø.6. TM. TT Z + Stroke ore 5 (.5") (") 5 (.5") 7/6-7/6-7/6-..6..55 /4-8.55 5/6-4.55 5/6-4 /...6.6...6.6.4.84.9 TM.5.5 TT.8.8.8 UM 4.5 5 5.5 UV.56.9.7.7.75.6.4.48 L XI.89.9.99 Z 4 4 4 Non-otating od Single etachable ear levis Mounting Type N K -cross - (NT) ø ø ø.6 M L X + Stroke Z + Stroke ore 5 (.5") (") 5 (.5") 7/6-7/6-7/6-..6. / / /.55.55.55 /4-8 5/6-4 5/6-4 /...6.6...6.6 L M.6.4.48.4.84.9.7.7.75 L X 5 5 5 Z 6 6 6 /

Medium uty ir ylinder Series N Non-otating od ouble ear levis Mounting Type N KX cross - (NT) ø ø ø.6 L S.H..S. W W Z + Stroke L M X + Stroke ore 5 (.5") (") 5 (.5") 7/6-7/6-7/6-..6. / / / W / / /.55 /4-8.55 5/6-4.55 5/6-4 /...6.6...6.6 L L M.6.4.48.4.84.9 L X 5 5 5 / Z 4 4 4 Note: Mounting dimensions are the same as N (M) except where marked ( ). Non-otating od Side Lug Mounting Type N KS Z + Stroke -cross - (NT) øs Screw (4) Hole ST / TS SW SU SU SW US XS SS + Stroke S ore 5 (.5") (") 5 (.5") MM 7/6-7/6-7/6-.55.55.55 /4-8 5/6-4 5/6-4 /...6..6.6..6 L.6.6.75.6.4.48.4.84.9 S SS.88.88 ST SU.94.94.94 SW S.94.94.94 TS.75.5.75 US.5 4 4.5 XS.8.8.8.7.7.75 Z 5.9 5.9 5.

Series N Medium uty ir ylinder Non-otating od Head Trunnion Mounting Type N KS -cross - (NT) ø 4- ouble od Non-otating asic Mounting Type N KW + Stroke - (NT) 7/6-UN 7/6-UN ø. ø.6 ø.6 ø. ø. + -. ir cushion adjustable.. Z + Stroke ore MM L Z 5 (.5") 7/6-..55 /4-8..6..4.7.75.6 4.75 (") 7/6-.6.55 5/6-4 /..6.9.84.7.75.4 4.75 5 (.5") 7/6-..55 5/6-4..9.9.75.88.48 4.88 ø.55 cross.75.8 K.75 9/6 cross. L + Stroke. + Stroke ZM + x Stroke ore L ZM K 5 (.5"). /4-8..6.4.7.78.6 5.78.8 (").6 5/6-4 /..6.84.7.8.4 5.8.4 5 (.5"). 5/6-4..9.75.98.48 5.98.4

Medium uty ir ylinder Series N ouble od Non-otating oot Mounting Type N KWL ZM + x Stroke + Stroke.75. - (NT). + Stroke 7/6-UN.8.75 7/6-UN ø. ø.6 ø.6 ø. ø. H.55 cross 9/6 cross S 6-ø (Hole) O. L + Stroke. O SL + Stroke ore O L ZM SL S H 5 (.5")...6.44.7.78.6.4 5.78 5.78.5.9.9 /4-8 (").6 /..6.56.7.8.4.84 5.8 5.8.75.69.44 5/6-4 5 (.5")...56.75.98.48.9 5.98 5.98.5..6 5/6-4 ouble od Non-otating ront lange Mounting Type N K 4-ø (Hole) ø 7/6-UN - (NT) + Stroke 7/6-UN ø. ø.6 ø.6 ø. 9/6 cross.8 T U.55 cross.75.8. L + Stroke K.75. + Stroke ZM + x Stroke ore L ZM T U K 5 (.5"). /4-8..6.4.7.78.6 5.78.75.8..8 (").6 5/6-4 /..6.84.7.8.4 5.8.8 4..8.4 5 (.5"). 5/6-4..9.75.98.48 5.98.88 4.6.8.4

Series N Medium uty ir ylinder ouble od Non-otating Side Tapped Mounting Type N KW ø 7/6-UN - (NT) + Stroke 7/6-UN / ouble od Non-otating enter Trunnion Mounting Type N KWT XI + / Stroke + Stroke -. UM UV ø. ø..6 ø.6 ø. ø. ø.6 ø.6 ø..55 cross 9/6 cross TN 4-NT N eep.75.8..94 L + Stroke ZM + x Stroke S + Stroke K.75. + Stroke.94 + Stroke ore L S ZM K TN N NT 5 (.5"). /4-8..6.4.7.78.6.9 5.78.8.6 9/ /4- (").6 5/6-4 /..6.84.7.8.4.94 5.8.4.88 7/6 5/6-8 5 (.5"). 5/6-4..9.75.98.48. 5.98.4.5 9/ -6.55 cross 7/6-UN - (NT) 9/6 cross 7/6-UN.75.75 ø.8.8 K. L + Stroke. + Stroke. TM. ZM + x Stroke ore L ZM UV TM K UM XI 5 (.5")...6.4.7.78.6 5.78..5.8 4.5.89 /4-8 (").6 /..6.84.7.8.4 5.8.56.4 5.9 5/6-4 5 (.5")...9.75.98.48 5.98.9.5.4 5.5.99 5/6-4 4

Medium uty ir ylinder Series N Stainless Steel od (X6) Specifications Stainless Steel piston rod is used to protect in harsh or wet environments. uto-switch mounting available. ore size (inch).5.5.5 4 Media ir Max. Operating ressure 5 psi (7.5 kgf/cm²) Min. Operating ressure 8 psi (.5 kgf/cm²) od Material SUS4 mbient and Media Temperature 4 to 4 (5 to 6 ) iston Speed to inch/sec (5 to 5mm/sec) Stroke Tolerance (mm) to.: ushion Mounting Types Standard Stroke List ore size Standard Stroke.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4,.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4.5, 4,,, 4, 5, 6, 8,,, 4, 6, 8,, 4, 8, +. ir ushion Standard asic, oot, lange Side Tapped, levis, Head Trunnion od Trunnion, enter Trunnion, Side Lug How To Order N MOUNTIN O STOK SUIX X6 x: N 5-4-X6 Low Speed (X9) uto-switch capable Stainless Steel od Specifications ore size (inch).5.5.5 4 Media ir Max. Operating ressure 5 psi (7.5 kgf/cm²) Min. Operating ressure 8 psi (.5 kgf/cm²) mbient and Media Temperature 4 to 4 (5 to 6 ) iston Speed ushion Mounting Types.4 to inch/sec ( to 5mm/sec) None asic, oot, lange Side Tapped, levis, Head Trunnion od Trunnion, enter Trunnion, Side Lug Smooth movements even at.4 to inch/sec uto switch mounting available. Standard Stroke List ore size Standard Stroke.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4,.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4.5, 4,,, 4, 5, 6, 8,,, 4, 6, 8,, 4, 8, How To Order N MOUNTIN O STOK N X9 x: N 5-4-X9 Standard uto-switch capable Low Speed 5

Series N Medium uty ir ylinder High Temperature (X6) Use at high temperature up to. Specifications ore size (inch).5.5.5 4 Media ir Max. Operating ressure 5 psi (7.5 kgf/cm²) Min. Operating ressure 8 psi (.5 kgf/cm²) mbient and Media Temperature 4 to ( to 5 ) Seal Material luro ubber iston Speed to inch/sec (5 to 5mm/sec) +. Stroke Tolerance (mm) to.: ushion ir ushion Standard Mounting Types Standard Stroke List asic, oot, lange Side Tapped, levis, Head Trunnion od Trunnion, enter Trunnion, Side Lug ore size Standard Stroke.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4,.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4.5, 4,,, 4, 5, 6, 8,,, 4, 6, 8,, 4, 8, How To Order N MOUNTIN O STOK SUIX X6 x: N 5-4-X6 Low Temperature (X7) uto-switch capable not available High Temperature Specifications ore size (inch).5.5.5 4 Media ir Max. Operating ressure 5 psi 7.5 kgf/cm²) Min. Operating ressure 8 psi (.5 kgf/cm²) mbient and Media Temperature to 4 ( to 6 ) Seal Material Low urometer Nitril ubber iston Speed to inch/sec ( to 5mm/sec) ushion None asic, oot, lange, enter Trunnion, Mounting Types Side Tapped, levis, Side Lug od and Head Trnnion Use at low temperature down to. Standard Stroke List ore size Standard Stroke.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4,.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4.5, 4,,, 4, 5, 6, 8,,, 4, 6, 8,, 4, 8, How To Order N MOUNTIN O STOK N X7 x: N 5-4-X7 Standard uto-switch capable not available Low Temperature 6

Medium uty ir ylinder Series N Special Trunnion Location (X46US) Specifications ore size (inch).5.5.5 4 Media ir Max. Operating ressure 5 psi (.75 kgf/cm²) Min. Operating ressure 8 psi (.5 kgf/cm²) mbient and Media Temperature 4 to 4 (5 to 6 ) Seal Material Nitrile ubber iston Speed to inch/sec (5 to 5mm/sec) ushion ir ushion Standard Mounting Type enter Trunnion How To Order Standard Stroke List ore size Standard Stroke.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4,.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4.5, 4,,, 4, 5, 6, 8,,, 4, 6, 8,, 4, 8, N T X46US uto Switch ore Size Standard Stroke Inches od oot ir ushion uto Switch Z imensions Use a four digit number X: 6 = 6. inches od over Trunnion Location Head over Trunnion Location Stroke Hundredths Of n Inch Special od Trunnion Location N T (5 to 4) - **** - X46US - **** UV 4- cross Z - (NT) ø. ø. -. + TT. TM. UM Z + Stroke ore MM TM TT UM UV L Z Z N Min. Max. 5 (.5") 7/6-. 9/6 /4-8..6..4.5.8 4.5.7.6 4.87.89 + Stroke (") 7/6-.6 9/6 5/6-4 /..6.6.84.8 5.56.7.4 4.87.9 + Stroke 5 (.5") 7/6-. 9/6 5/6-4..6.9.5.8 5.5.9.75.48 4.9.99 + Stroke 5 (.5") -6.9 / / / -4 /.57.8.76 4.5.4 6.5 4..4.7 4 /4 5 5/64.6.9 + Stroke 4 (4") -6 4.7 / / / -4 4 / /.57.8. 5.5.57 7.5 5..4.7 4 /4 5 5/64.75.95 + Stroke 7

Series N Special od Trunnion Location N T (5 to 4) - **** - X46US - Medium uty ir ylinder ø UV 4-. cross Z - (NT) ø. -. + TT. TM. UM Z + Stroke ore MM TM TT UM UV L Z Z 5 (.5") 7/6-. 9/6 /4-8..6..4.5.8 4.5.7.6.8 4 (") 7/6-.6 9/6 5/6-4 /..6.6.84.8 5.56.7.4.8 4 5 (.5") 7/6-. 9/6 5/6-4..6.9.5.8 5.5.9.75.48.85 4 5 (.5") -6.9 / / / -4 /.57.8.76 4.5.4 6.5 4..4.7 4 /4.58 5 5/64 4 (4") -6 4.7 / / / -4 4 / /.57.8. 5.5.57 7.5 5..4.7 4 /4.7 5 5/64 Special Head Side Trunnion Location N T (5 to 4) - **** - X46US - UV 4- cross Z - (NT) ø. + ø.. TM. TT UM Z + Stroke ore MM TM TT UM UV L Z Z 5 (.5") 7/6-. 9/6 /4-8..6..4.5.8 4.5.7.6 4.97 + Stroke (") 7/6-.6 9/6 5/6-4 /..6.6.84.8 5.56.7.4 4. + Stroke 5 (.5") 7/6-. 9/6 5/6-4..6.9.5.8 5.5.9.75.48 4.4 + Stroke 5 (.5") -6.9 / / / -4 /.57.8.76 4.5.4 6.5 4..4.7 4 /4 5 5/64.8 + Stroke 4 (4") -6 4.7 / / / -4 4 / /.57.8. 5.5.57 7.5 5..4.7 4 /4 5 5/64.7 + Stroke 8

Medium uty ir ylinder Series N Oversized od with Special Trunnion Location (X5 - X46US) Standard Stroke List ore Size Standard Stroke,.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4.5, 4,,, 4, 5, 6, 8,,, 4, 6, 8,, 4, 8, How To Order N T O STOK X5 X46US Z x: NT 5-4-X5-X46US-7 uto-switch capable Oversized od Z imension Z-imension use a four digit number Special Trunnion Location N T ( to 4) - **** - X5 - X46US - **** Z UM ø. cross - (NT) UV ø. -.. TM. TT Z + Stroke ore MM TM TT UM UV L Z Z N Min. Max. (") -6.6 / / 5/6-4 /..6.6.84.8 5.56.9.4 5 /8.5.9 + Stroke 5 (.5") -6. / / 5/6-4..6.9.5.8 5.5.9..48 5 /4.8.7 + Stroke 5 (.5") -4.9 / /4-4 /.57.8.76 4.5.4 6.5 4..59 4 /4.7 6 5/64.89.56 + Stroke 4 (4") -4 4.7 / /4-4 4 / /.57.8. 5.5.57 7.5 5..59 4 /4.7 6 5/64 4..59 + Stroke 9

Series N Medium uty ir ylinder Stainless Steel Tie ods / Tie od Nuts (XUS) Specifications ore size (inch).5.5.5 4 Media ir Max. Operating ressure 5 psi (7.5 kgf/cm²) Min. Operating ressure 8 psi (.5 kgf/cm²) mbient and Media Temperature 4 to 4 (5 to 6 ) Seal Material Nitrile ubber iston Speed to inch/sec (5 to 5mm/sec) Stroke Tolerance to.: ±. ushion ir ushion oth nds Mounting Types asic, oot, lange, enter Trunnion, Side Tapped, levis, od Trunnion, Head Trunnion, enter Trunnion, Side Lug Stainless steel piston rod is used to protect in harsh or wet environments uto-switch mounting available Standard Stroke List ore Size Standard Stroke.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4,.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4.5, 4,,, 4, 5, 6, 8,,, 4, 6, 8,, 4, 8, How To Order N MOUNTIN O STOK SUIX XUS x: N 5--XUS Stainless Steel iston od, Tie ods, Tie od Nuts, and ushion Valve Needle asic Mounting Type N (MXO Mounting Style) - XUS Z + Stroke ø - (NT) cross ore MM L Z 5 (.5") 7/6-. 9/6 /4-8..6..4.7.6 4 (") 7/6-.6 9/6 5/6-4 /..6.6.84.7.4 4 5 (.5") 7/6-. 9/6 5/6-4..6.9.75.48 4 5 (.5") -6.9 / / / -4 /.57.8.76.4.7 4 /4 5 5/64 4 (4") -6 4.7 / / / -4 4 / /.57.8..4.7 4 /4 5 5/64

Medium uty ir ylinder Series N od oot oot Material Suffix ode Material Max. Temperature Nylon 4 (6 ) K Neoprene ( ) Maximum temperature is for boot only. How To Order od boots are used to protect the surface of a piston rod in harsh environments. N MOUNTIN O STOK USHION OOT x: N5- uto-switch capable od oot -Nylon od oot K-Neoprene od oot od oot imensions ore øe f L to. to 4 4. to 6 6. to 8 8.to. to. to 4 4. to 6 6. to. to 4 4. to 8 5 (.5 ).75.75.74 ( ).75.75.74 6 5 (.5 ).75.75.74.5.5.5.5 4 5 6 5 (.5 ).5.968.984 6 7 4 (4 ).5.968.984 6 7 Wf ore to. to 4 4. to 6 6. to 8 8. to. to. to 4 4. to 6 6. to. to 4 4. to 8 5 (.5 ).97.47.97.47.97 4.47 4.97 5.47 6.47 ( ).97.47.97.47.97 4.47 4.97 5.47 6.47 7.47 5 (.5 ).97.47.97.47.97 4.47 4.97 5.47 6.47 7.47 5 (.5 )..8..8 4. 4.8 5. 5.8 6.8 7.8 8.8 4 (4 )..8..8 4. 4.8 5. 5.8 6.8 7.8 8.8 ore Z to. to 4 4. to 6 6. to 8 8. to. to. to 4 4. to 6 6. to. to 4 4. to 8 5 (.5 ) 5.687 6.87 6.687 7.87 7.687 8.87 8.687 9.87.87 ( ) 5.687 6.87 6.687 7.87 7.687 8.87 8.687 9.87.87.87 5 (.5 ) 5.8 6. 6.8 7. 7.8 8. 8.8 9.97.. 5 (.5 ) 6.765 7.65 7.765 8.65 8.765 9.65 9.765.65.65.65.65 4 (4 ) 6.765 7.65 7.765 8.65 8.765 9.65 9.765.65.65.65.65

Series N Medium uty ir ylinder Oversized od / Standard od and Non-otating (X5 / X9US) Specifications ore size (inch).5.5 4 Media ir Max. Operating ressure Min. Operating ressure mbient and Media Temperature iston Speed ushion Mounting Types 5 psi (7.5 kgf/cm²) 8 psi (.5 kgf/cm²) 4 to 4 (5 to 6 ) to inch/sec (5 to 5mm/sec) ir ushion Standard asic, oot, lange, enter Trunnion, Side Tapped, Side Lug How To Order Oversized od / Standard N MOUNTIN O STOK X5 x: N 5--X5 uto-switch capable Oversized / Standard od Specifications for X9US Max. Operating ressure Min. Operating ressure Oprating Temperature ange iston Speed ange ushion Mounting Max. otating Torque Non-rotating od ccurancy dditional eature 5 psi 5 psi 4 to 4 (5 to 6 ) to inch/sec (5 to 5mm/sec) ir Standard-oth ends See How to Order 6.9lb in (. &.5 bore) 8.lb in (.5 & 4. bore) ±.5 (. &.5 bore) ±. (.5 & 4. bore) Oversized iston od (X5) How To Order Oversized od/non-otating N K MOUNTIN O STOK X9US x: NK --X9US Standard Stroke List ore Size Standard Stroke,.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4.5, 4,,, 4, 5, 6, 8,,, 4, 6, 8,, 4, 8, uto-switch capable Oversized / Non-otating od Oversized od asic Type N (X5) Q Width cross ø cross - (NT) ore 5 5 4 Q /6 /6 / X9US Option TN 4-NT N eep XT SN Z + Stroke ore MM (") 5 (.5") 5 (.5") 4 (4") -6-6 -4-4.6..9 4.7.5.5 / / / / /4 /4 5/6-4 /. 5/6-4 -4-4 4 / / /.6..57.57.6.6.8.8.84.9.76. N 7/6 9/ NT 5/6-8 -6 /- /- TN.875.5.5.6 XT 5/6 5/6 /6 /6.9..59.59 L 4 /4 4 /4.4.48.7.7 SN /4 Z 5 /8 5 /4 6 5/64 6 5/64

Medium uty ir ylinder Series N Oversized od oot Mounting Type N L (X5) ore 5 5 4 Q /6 /6 Q Width cross X9US Option S ø T H 6- (Hole) cross Z + Stroke X + Stroke - (NT) O L L O S + Stroke ore (") 5 (.5") 5 (.5") 4 (4") MM -6-6 -4-4.6..9 4.7 / / H L /6 7/6 /8 /6 5/6 /4 4 / /4 /4 O T 9/6 /8 9/6 /8 /64 /64.5.5 / / 5/6-4 5/6-4 / /4 / /4-4 -4 / 4 /. / /.6..57.57.6.6.8.8.84.9.76. S /4 /.9..59.59.4.48.7.7 L S 6 X 6 Z 6 9/6 6 /8 6 /8 6 /6 4 /4 7 7 4 /4 7 7 7 7 Oversized od ront lange Mounting Type N (X5) Q Width cross ø 4-ø (hole) cross - (NT) ore 5 5 4 Q /6 /6 X9US Option T U W Z + Stroke ore MM (") 5 (.5") 5 (.5") 4 (4") -6-6 -4-4.6..9 4.7.5.5 / / / / /4 /4 5/6-4 5/6-4 -4-4 /. 4 / / / 7/6 7/6.6..57.57.6.6.8.8.84.9.76. T 4 /6 5 7/6 U 4 /8 4 5 / 6 /4 W L 4 /4 4 /4.9..59.59.4.48.7.7 Z 5 /8 5 /4 6 5/64 6 5/64

Series N Medium uty ir ylinder Oversized od ear lange Mounting Type N (X5) Q Width cross cross - (NT) 4-ø (Hole) ø ore 5 5 4 Q /6 /6 X9US Option X + Stroke Z + Stroke T U ore (") 5 (.5") MM -6-6 5 (.5") -4 4 (4") -4.6..9 4.7.5.5 / / / / /4 /4 5/6-4 5/6-4 -4-4 / 4 /. / / 7/6 7/6.6..57.57.6.6.8.8.84.9.76. T 4 /6 5 7/6 U 4 /8 4 5 / 6 /4.9..59.59.4.48.7.7 X 5 5 /8 5 5 Z 5 5 / 6 / 6 / Oversized od ouble etachable ear levis Mounting Type N (X5) Q Width cross -cross - (NT) L ø W W ore 5 5 4 Q /6 /6 ø X9US Option X + Stroke Z + Stroke L M ore MM (") 5 (.5") 5 (.5") 4 (4") -6-6 -4-4.6..9 4.7 / / / / /4 /4 / / W / / /4 /4 5/6-4 5/6-4 -4-4 / 4 /. / /.6..57.57.6.6.8.8 L /4 /4 L M / /.84.9.76. X 6 /8 6 /4 7 7.9..59.59 L 4 /4 4 /4.4.48.7.7 Z 6 6 8 / 8 / 4

Medium uty ir ylinder Series N Oversized od enter Trunnion Mounting Type N T (X5) ore 5 5 4 Q /6 /6 Q Width cross X9US Option UV ø UM.. TM. ø. -. cross XI + / Stroke - (NT) TT Z + Stroke ore MM (") 5 (.5") 5 (.5") 4 (4") -6-6 -4-4.6..9 4.7 / / / / / / /4 /4 5/6-4 5/6-4 -4-4 / 4 /. / /.6..57.57.6.6.8.8.84.9.76. TM / 4 / 5 /4 TT.8.8.4.57 UM 5 5 / 6 / 7 /4 UV.56.9 4. 5..9..59.59 L 4 /4 4 /4.4.48.7.7 XI.9.7.95.99 Z 5 /8 5 /4 6 5/64 6 5/64 Oversized od Single etachable ear levis Mounting Type N (X5) Q Width cross - cross - (NT) ø ø ore 5 5 4 Q /6 /6 X9US Option X + Stroke Z + Stroke L M ore (") 5 (.5") 5 (.5") 4 (4") MM -6-6 -4-4.6..9.9 / / / / /4 /4 / / /4 /4 5/6-4 5/6-4 -4-4 / 4 /. / /.6..57.57.6.6.8.8 L /4 /4 M.84.9.76. X 6 /8 6 /4 7 7.9..59.59 L 4 /4 4 /4.4.48.7.7 Z 6.75 6.88 8.6 8.6 5

Series N Medium uty ir ylinder Oversized od ouble ear levis Mounting Type N X (X5) Q Width cross -cross - (NT) S.H..S. W W ø ø ore 5 5 4 Q /6 /6 L X9US Option Z + Stroke X + Stroke L M ore (") 5 (.5") 5 (.5") 4 (4") MM -6-6 -4-4.6..9 4.7 / / / / /4 /4 / / W / / /4 /4 5/6-4 5/6-4 -4-4 / 4 /. / /.6..57.57.6.6.8.8 L.6.6.5.5 L /4 /4 M.84.9.76. X 5 5 7 /8 7 /8.9..59.59 L 4 /4 4 /4 Z.4 5 /8.48 5 /4.7 6 5/64.7 6 5/64 Oversized od Head Trunnion Mounting Type N (X5) Q Width cross cross - (NT) 4- ø ore 5 5 4 Q /6 /6 ø. + -. X9US Option Z + Stroke.. ore (") 5 (.5") 5 (.5") 4 (4") MM -6-6 -4-4.6..9 4.7 / / / / /4 /4 5/6-4 5/6-4 -4-4 / 4 /. / /.6..57.57.6.6.8.8.84.9.76..9..59.59 L 4 /4 4 /4.4.48.7.7 Z 5 /8 5 /4 6 5/64 6 5/64 6

Medium uty ir ylinder Series N djustable Stroke - xtended (X8) Specifications ore size (inch).5.5.5 4 Media ir Max. Operating ressure 5 psi (7.5 kgf/cm²) Min. Operating ressure 8 psi (.5 kgf/cm²) mbient and Media Temp. 4 to 4 (5 to 6 ) iston Speed to inch/sec (5 to 5mm/sec) ushion ir ushion Standard Mounting Types asic, oot, lange, enter Trunnion, Side Tapped The extended stroke stop position is infinitely adjustable within the adjustable range. uto switch capable Standard Stroke List ore size Standard Stroke.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4,.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4.5, 4,,, 4, 5, 6, 8,,, 4, 6, 8,, 4, 8, How To Order N 5 4 X8 uto Switch Mounting ore Stroke djustment ange : ~ : ~ djustable Stroke imensions cross L + Stroke - (NT) d + Stroke + djustable ange Stroke c + djustable ange ø / øb TN 4-NT N eep XT S + Stroke K ZZ + x Stroke + djustable ange (:", :") ore MM K L ZZ b c d S NT N TN 5 (.5") 7/6-. 9/6 /4-8..6 9/.4.7.78.6 6.58 /.5.8.9 /4-9/ (") 7/6-.6 9/6 5/6-4 /..6 /.84.7.8.4 7. /.64.9.94 5/6-8 7/6 5 (.5") 7/6-. 9/6 5/6-4. /.9.75.98.48 7.7 /.64.9. -6 9/ /4 5 (.5") -6.9 / / -4 /.57 7/64.76.4 4.64.7 9.8 9/.48.7.5 /- / 4 (4") -6 4.7 / / -4 4 / /.57 7/64..4 4.64.7 9.8 9/.48.7.5 /- /6 7

Series N Medium uty ir ylinder djustable Stroke - eturn (X9) Specifications ore size (inch).5.5.5 4 Media ir Max. Operating ressure 5 psi (7.5 kgf/cm²) Min. Operating ressure 8 psi (.5 kgf/cm²) mbient and Media Temp. 4 to 4 (5 to 6 ) iston Speed to inch/sec (5 to 5mm/sec) ushion ir ushion Standard Mounting Types asic, oot, lange, enter Trunnion, Side Tapped The return stroke stop position is infinitely adjustable within the adjustable range. uto switch capable Standard Stroke List ore size Standard Stroke.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4,.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4.5, 4,,, 4, 5, 6, 8,,, 4, 6, 8,, 4, 8, How To Order N 5 4 X9 uto Switch Mounting ore Stroke djustment ange : ~ : ~ djustable Stroke etract imensions () (NT) ø cross mm / cross TN 4-NT N eep XT SN + Stroke ZZ + Stroke + djustable ange K d + djustable ange ore MM 5 (.5") 7/6-. (") 5 (.5") 5 (.5") 4 (4") 7/6-7/6- -6-6.6..9 4.7 / / / / 9/6 9/6 9/6 /4-8 5/6-4 / 5/6-4 -4-4 4 /.. / /.6.6..57.57 K. / 9/.6 / /.6 / /.. 7/64 7/64.4.84.9.7.7.75.76.4..4 L 4 /4 4 /4.6.4.48.7.7 ZZ 6.44 6.44 6.44 8. TN XT 5/6 5/6 /4 5/6 / 7/6 8. /6 7/6 SN /4 /4 d mm NT N.8 M6 x.5 /4-9/.8 M6 x.5 5/6-8 7/6.69 M6 x.5.4 M4 x.5.4 M4 x.5-6 /- /- 9/ 8

Medium uty ir ylinder Series N ual Operation - ouble od (X) Specifications ore size (inch).5.5.5 4 Media ir Max. Operating ressure 5 psi (7.5 kgf/cm²) Min. Operating ressure 8 psi (.5 kgf/cm²) mbient and Media Temp. 4 to 4 (5 to 6 ) iston Speed to inch/sec (5 to 5mm/sec) ushion ir ushion Standard Mounting Types asic, oot, lange, enter Trunnion, Side Tapped 4 positions available from a single cylinder uto switch capable Standard Stroke List ore Size Standard Stroke.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4,.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4.5, 4,,, 4, 5, 6, 8,,, 4, 6, 8,, 4, 8, How To Order N 5 4 N X imensions uto Switch Mounting ore Stroke Stroke ual Operation ouble od ushions - oth nds N w/o ushions H Head nd od nd K + Stroke 4- (NT) + Stroke ø cross cross / TN 4-NT Stroke Stroke N eep XT SN + Stroke ( + ) L + Stroke ( + ) ZZ + Stroke ( + ) XT ore MM 5 (.5") (") 5 (.5") 5 (.5") 4 (4") 7/6-7/6-7/6- -6-6..6..9 4.7 / / / / 9/6 9/6 9/6 /4-8 5/6-4 5/6-4 -4-4 / 4 /.. / /.6.6..57.57 K 9/ / / 7/64 7/64.4.84.9.76..7.7.75.4.4 L 7.44 7.5 7.76 8.94 8.94.6.4.48.7.7....57.57 ZZ 9.44 9.5 9.76.69.69 SN 5.56 5.64 5.88 6.8 6.8 TN /4 / /6 XT 5/6 5/6 5/6 7/6 7/6 NT /4-5/6-8 -6 /- /- N 9/ 7/6 9/ 9

Series N Medium uty ir ylinder ual Operation - Single od (X) Specifications ore size (inch).5.5.5 4 Media ir Max. Operating ressure 5 psi (7.5 kgf/cm²) Min. Operating ressure 8 psi (.5 kgf/cm²) mbient and Media Temp. 4 to 4 (5 to 6 ) iston Speed to inch/sec (5 to 5mm/sec) ushion ir ushion Standard Mounting Types asic, oot, lange, levis Side Lug, Side Tapped positions can be obtained from a single cylinder. Twice the force is available for the extended stroke. uto switch capable Standard Stroke List ore Size Standard Stroke.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4,.5,,, 4, 5, 6, 8,,, 4, 6, 8,, 4.5, 4,,, 4, 5, 6, 8,,, 4, 6, 8,, 4, 8, xample: N5-+H-X will stroke then an additional for a total stroke of 5. The front cylinder (rod end) must be equal to 5 to allow the full stroke. How To Order N 5 + H X imensions uto Switch Mounting ore Stroke Stroke - ual Operation Single od ushions - oth nds N w/o ushions H Head nd od nd ø cross 4- (NT) + Stroke / TN 4-NT N eep XT Stroke Stroke SN + Stroke + Stroke + Stroke Z + Stroke + Stroke ore MM NT TN XT L SN Z N 5 (.5") 7/6-. 9/6 /4-8..6. /4-.4 5/6.7 7.6.6.4.4 5.89 8.9 9/ (") 7/6-.6 9/6 5/6-4 /..6.6 5/6-8.84 5/6.7 7.6.4.44. 5.89 8.8 7/6 5 (.5") 7/6-. 9/6 5/6-4..6-6.9 /4 5/6.75 7.8.48.5. 6. 8.5 9/ 5 (.5") -6.9 / / / -4 /.57.8 /-.76 / 7/6.4 8.5.7.76.5 6.89. 4 (4") -6 4.7 / / / -4 4 / /.57.8 /-. /6 7/6.4 8.5.7.76.5 6.89. 4

Medium uty ir ylinder Series N Special od nd Modifications How to Order The N series cylinders are available with a variety of special rod end modifications to suit your application through our Simple Special ordering process. The Simple Special System is a global effort to quickly and efficiently respond to our customer requests for a non-standard catalog option. The chart below outlines the applicable types available. To order the correct rod end modification, please contact your local SM Sales Office or SM Technical Sales epresentative. od nd Shape Symbol: Symbol: Symbol: Symbol: 4 Symbol: 5 Symbol: 6 Symbol: 7 Symbol: 8 Symbol: 9 Symbol: Symbol: Symbol: Symbol: Symbol: 4 Symbol: 5 Symbol: 6 Symbol: 7 Symbol: 8 Symbol: 9 Symbol: Symbol: Symbol: Symbol: Symbol: 4 Symbol: 5 Symbol: 6 Symbol: 7 Symbol: 8 Symbol: 9 Symbol: 4

Series N Medium uty ir ylinder ccessories ye rackets art No L L M M N-5 / / / / 9/6.6 N-5 /4 7/ / /4.56 N-8 / / 4 / /4 / /4.5 N- / 5 /8.8 N- / 9/ 6 / /8 /4 /8 4.95 N-4 / /6 7 / / / 7/6 5.75 N-4 / /6 8 / 4 / 6.58 N-4 5/6 9 / 5 /4 /4 7.5 Note: ivot in is not included. levis rackets art No W L L M M N-5..785 / / -4 / / / 9/6 N-5.6 9/6.65 / - / /6 /6 N-8 4.6 /4.55-8 4 / /4 /4 N- 5.4 /6. -8 5 N- 7 4 5/6.5 /4-4 6 / /8 N-4 8. 5.5 /4-4 7 / / /8 /8 N-4 9. 6 9/. / / - 8 / 4 / / N-4.6 7 /. / /4-9 / 4 /4 Note: ivot in is not included. od levises art No H W L N-5.765.5 / / 7/6- / N-5.65.75 /4 /4-6 N-8.55 /8 / / / -4 N-. 4 /8 /8 /4 - N-.5 4 / /4 /4 /4 / - N-4.5 5 / 5/6 /4 5/6 / - N-4. / 6 / / / / / /4 - / N-4. 6 / /4 / / - Order to Match od Thread od yes art No NI-5 / / 7/6 NI-5 /6 /4-6 NI-8 /6 / /6-4 NI- 7/6 9/6 /4 - NI- /4 4 / / - NI-4 5 / / - NI-4 / 5 /6 / /6 /4- NI-4 / 6 /8 /4 /- ivot in art No L N-5 / N-5 N-8 /8 N- 4 /8 N- 5 /8 N-4 5 /8 N-4.5 6.9 N-4 6.5 Note: etainer ings are included. ivot in art No L N-5.5 -..6.8.94 N-5.75 -..4..7 Note: otter ins are included. ø L ø 4

Medium uty ir ylinder Series N How to Order uto Switches Wire Lead Type - onnector Type - or standard part number please see applicable auto switches on page 4 to 47. Lead wire length Nil.5 (m) (.64 ft) L (m) (9.84 ft) Z 5 (m) (6.4 ft) uto Switch Mounting racket / art No. ore Model No. -5, -5-6, -5 5 (.5 ) ( ) 5 (.5 ) 5 (/5 ) 4 (4 ) NT-5 NT- NT- NT-5 NT-5 or standard part number please see applicable auto switches on page 4 to 47. Lead wire length S.5 (m) M. (m) L. (m) onnector type M8- pins M8-4 ins M-4 ins onnector Style in arrangement M8-pins M8-4pins M-4pins 4 4 4 pplicable standards IS 454, IS 455, I 947-5-, N 4 Impact resistant m/s I degress of protection I-67 (I59 standard) Insulation resistance MΩ or more at 5V meg. Withstand voltage 5V minute (between contacts), leakage current m or less. Sensor type -wire -wire non-polar -wire 4-wire pin rown rown rown Lead wire color pin pin rown Orange lue lue 4 pin lue lue lack lack Meaning of contact No. pin pin pin 4 pin OUT (+) OUT ( ) OUT (+) OUT (±) (+) ( ) OUT (+) iagnistic Output ( ) OUT onnector M8- pins / 4 pins Sensor ø Lead wire length.4 M-4 pins Sensor ø4 Lead wire length 44 4

Series N Medium uty ir ylinder rommet Specifications -5 (With indicator light) uto switch model number -5 pplication Load voltage Max. load current and range ontact protection circuit Internal voltage drop Indicator light L 4V 5 to 5m None -6 (Without indicator light) uto switch model number pplication Load voltage Max. load current ontact protection circuit 4V 5m 4V 5 to 5m -64 elay/l V 5m uilt-in L: rogrammable Logic ontroller -54 elay/l V 5 to 5m V 5 to.5m uilt-in.4v ON: When red light emitting diode V.5m -56 I circuit 4 to 8V m None.8V or less -67 L/I circuit Max. 4V m None Internal resistance Ω Ω (Including m lead wire) Internal ircuit ( ): If not applicable for I Standard -5 eed switch OUT( ) lue (lack) L esistance OUT(+) rown (ed) Lead wire Oilproof vinyl heavy insulation cable, ø4,.mm, cores (rown, lue),.5m or ø4,.mm, cores (rown, lack, lue),.5m efer to common specifications and lead wire length on page 48. imensions Zener diode -54 OUT( ) to lue (lack) eed switch Zener diode L esistance hoke coil OUT(+) to rown (ed) Surge absorber -56 L (+) rown (ed) (+) eed switch esistance everse flow prevent diode Load OUT lack (White) ( ) lue (lack) ower voltage ( ) -64 OUT( ) to lue (lack) ± eed switch hoke coil OUT(±) to rown (ed) Operation ange (l imension) ore size ctuator series / / /4 4 N.54.9.4.4.4 Note: verage value at normal temperature including hysteresis. (Tolerance ± %) Surge absorber -67 OUT( ) lue (lack) ± eed switch OUT(±) rown (ed) 44

Medium uty ir ylinder Series N rommet The suitable operating point can be indicated with a green light. (ed reen ed) Specifications -59W (With indicator light) uto switch model number pplication Load voltage Load current range ontact protection circuit Internal voltage drop Indicator light L: rogrammable Logic ontroller -59W elay/l 4V 5 to 4m uilt-in 4V Operating point: ed light emitting diode Suitable operating point: reen light emitting diode Lead wire Oilproof vinyl heavy insulation cable, ø4,.mm, cores (rown, lue),.5m efer to common specifications and lead wire length on page 48. Internal ircuit ( ): If not applicable for I Standard imensions -59W Main circuit of switch eed switch L hoke coil Zener diode OUT(+) rown (ed) OUT( ) lue (lack) Indicator light/operation Operation ange (l imension) ctuator series / ore size / /4 4 N.54.9.4.4.4 Note: verage value at normal temperature including hysteresis. (Tolerance ± %) 45

Series N Medium uty ir ylinder Internal ircuit ( ): If not applicable for I Standard -59 rommet Specifications -5 /-5 uto switch model number Wiring Output pplication ower voltage urrent consumption Load voltage Load current Internal voltage drop urrent leakage Indicator light -59 NN 8V 4m.5V or less.8v or less at m of load current wire -5 N I circuit/elay/l 5//4V (4.5 to 8V) m 8m.8V or less μ at 4V L: rogrammable Logic ontroller -59 4V elay/l 4V ( to 8V) 5 to 4m 4V or less.8m at 4V ON: When red light emitting diode wire -5 elay/l 8 to 6V 5 to 8m 4V or less m at V.5m at V Lead wire Oilproof vinyl heavy insulation cable, ø4,.mm, cores (rown, lack, lue), cores (rown, lue),.5m efer to common specifications and lead wire length on page 48. Main ircuit of switch (+) rown (ed) OUT lack (White) imensions -5 differs in the shape, most sensitive position and operation range from other switches. ontact SM for the details. ( ) lue (lack) -5 (+) rown (ed) Main ircuit of switch OUT lack (White) ( ) lue (lack) -59 OUT(+) rown (ed) Main ircuit of switch -5 OUT( ) lue (lack) Operation ange (l imension) ctuator series / ore size / /4 4 N.54.9.4.4.4 Note: verage value at normal temperature including hysteresis. (Tolerance ± %) Main ircuit of switch OUT(+) rown (ed) OUT( ) lue (lack) 46

Medium uty ir ylinder Series N rommet The output signal can be detected in an unsteady detecting area. Internal ircuit ( ): If not applicable for I Standard Specifications -59 uto switch model number Wiring Output iagnostic output pplication ower voltage urrent consumption Load voltage Load current Internal voltage drop urrent leakage Indicator light L: rogrammable Logic ontroller -59 4 wire NN Normal operation I circuit/elay/l 5//4V (4.5 to 8V) m 8V 4m.5V (.8V at m) μ at 4V Operating point: ed light emitting diode Suitable operating point: reen light emitting diode Lead wire Oilproof vinyl heavy insulation cable, ø4,.mm, 4 cores (rown, lack, Orange, lue),.5m efer to common specifications and lead wire length on page 48. Main ircuit of switch (+) rown (ed) OUT (Normal output) lack (White) OUT (iagnostic output) Orange (ellow) ( ) lue (lack) iagnostic Output Operation The diagnostic output is detected when detecting position remains at unsteady area only, not available at the most suitable operating area, that is to say, diagnostic signal can be output only when the detecting position is far from the suitable position for normal operation. imensions Operation ange (l imension) ore size ctuator series / / /4 4 N.54.9.4.4.4 Note: verage value at normal temperature including hysteresis. (Tolerance ± %) 47

Series N Medium uty ir ylinder rommet The suitable operating point can be indicated with a green light. (ed reen ed) Specifications -5 W/-59W (With indicator light) uto switch model number Wiring Output pplication ower voltage urrent consumption Load voltage Load current Internal voltage drop urrent leakage -59W NN wire I circuit/elay/l 5//4V (4.5 to 8V) m 8V 4m.5V (.8V at m load current) μ at 4V -5W N 8m.8V L: rogrammable Logic ontroller -59W wire 4V elay/l 4V ( to 8V) 5 to 4m 4V.8m at 4V Indicator light Operating point: ed light emitting diode Suitable operating point: reen light emitting diode Lead wire Oilproof vinyl heavy insulation cable, ø4,.mm, cores (rown, lack, lue), cores (rown, lue),.5m Internal ircuit ( ): If not applicable for I Standard -59W efer to common specifications and lead wire length on page 48. imensions (+) rown (ed) Main circuit of switch OUT lack (White) ( ) lue (lack) -5W OUT(+) rown (ed) Main circuit of switch OUT( ) lue (lack) -59W OUT(+) rown (ed) Main circuit of switch OUT( ) lue (lack) Indicator light/operation Operation ange (l imension) ore size ctuator series / / /4 4 N.54.9.4.4.4 Note: verage value at normal temperature including hysteresis. (Tolerance ± %) 48

Medium uty ir ylinder Series N rommet Water (coolant) resistant performance aution recautions onsult SM if using coolant liquid other than water based solution. Specifications -5L (With indicator light) uto switch model number Wiring Output pplication ower voltage urrent consumption Load voltage Load current Internal voltage drop urrent leakage Indicator light L: rogrammable Logic ontroller -5L wire 4V elay/l 4V ( to 8V) 5 to 4m 4V.8m at 4V Operating point: ed light emitting diode Suitable operating point: reen light emitting diode Lead wire Oilproof vinyl heavy insulation cable, ø4,.mm, cores (rown, lue), m (Standard) efer to common specifications and lead wire length on page 48. Internal ircuit ( ): If not applicable for I Standard imensions OUT(+) rown (ed) Main circuit of switch OUT( ) lue (lack) Indicator light/operation Operation ange (l imension) ore size ctuator series / / /4 4 N.54.9.4.4.4 Note: verage value at normal temperature including hysteresis. (Tolerance ± %) 49

Series N Medium uty ir ylinder rommet With built-in O-delay timer (ms) Internal ircuit ( ): If not applicable for I Standard Specifications L: rogrammable Logic ontroller -5NTL (With indicator light) uto switch model number -5NTL Wiring wire Output NN Output operation Off-delay Operation time ms Off-delay time ±5ms pplication I circuit/elay/l ower voltage 5//4V (4.5 to 8V) urrent consumption m Load voltage 8V Load current 8m Internal voltage drop.5v (.8V at m) urrent leakage μ at 4V Indicator light ON: When red light emitting diode Lead wire Oilproof vinyl heavy insulation cable, ø4,.mm, cores (rown, lack, lue), m (Standard) efer to common specifications and lead wire length on page 48. Timer Operation Main circuit of switch (+) rown (ed) OUT lack (White) ( ) lue (lack) etection of immediate positioning for high-speed cylinder etecting point dispersion occurs due to response time of L (sequencer); e. g. scanning. x.) ylinder speed- mm/sec. Sequencer response time-. sec. etecting point despersion-within mm (=mm/sec. x.sec.) Take L response time into consideration when using. imensions 5 Operation ange (l imension) ore size ctuator series / / /4 4 N.54.9.4.4.4 Note) verage value at normal temperature including hysteresis. (Tolerance ± %)

Medium uty ir ylinder Series N uto Switch Specification uto Switch ommon Specifications uto switch style urrent leakage Operating time Shock resistance eed switch None.ms m/s Solid state switch -wire: μ or less, -wire: m or less Note ) ms or less m/s Insulation resistance 5 M Ω or more at 5MV (between lead wire and the case) Withstand voltage mbient temperature 5V/min. Note ) (between lead wire and the case) to 6 V/min. (between lead wire and the case) rotective construction I59 Standard I67, Note ) Waterproof construction (IS9) Note ) onnector style (-7/8/7/8) and -9/9 /9/9 V style: V/min. (between lead wire and the case) Note ) I59 Standard I6, ainproof construction (IS9) for Terminal conduit style (-/ / /9/9/9/K9/K9/K9) and IN teminal style (-44/44/44). Note ) xcept solid state switch with timer (-M5 TL, 5NTL, 7NTL, 5NTL) and uto switch for strong magnetic field resistance (-5WL). -5: 5ms or less Lead Wire Length -7 L Lead wire length Nil.5m L m Z N 5m None pplicable for the connector style (- ) only pplicable auto switch with 5 meter lead wire ("Z") eed switch: -5/54, -7 ()/8, -7()(H)/8, -5/54, -Z7, -9/97/9/9 Solid state switch: Manufactured upon receipt of order as standard (xcept -9/9lV) The standard lead wire length of solid state switch with timer or with water resistant - color indication is meters. (Not available.5m) The standard lead wire length of strong magnetic field resistant solid state switch is or 5 meters. (Not available.5m) art No. of lead wire with connector (vailable for connector style only.) art No. Lead wire length -L5.5m -L m -L5 5m 5

Series N Safety Instructions These safety instructions are intended to prevent a hazardous situation and/or equipment damage. These instructions indicate the level of potential hazard by a label of "aution", "Warning" or "anger". To ensure safety, be sure to observe ISO 444 Note ), IS 87 Note ) and other safety practices. aution : Operator error could result in injury or equipment damage. Warning : Operator error could result in serious injury or loss of life. anger : In extreme conditions, there is a possible result of serious injury or loss of life. Note ) ISO 444: neumatic fluid power -- ecommendations for the application of equipment to transmission and control systems Note ) IS 87: eneral ules for neumatic quipment Warning. The compatibility of pneumatic equipment is the responsibility of the person who designs the pneumatic system or decides its specifications. Since the products specified here are used in various operating conditions, their compatibility for the specific pneumatic system must be based on specifications or after analysis and/or tests to meet your specific requirements.. Only trained personnel should operate pneumatically operated machinery and equipment. ompressed air can be dangerous if handled incorrectly. ssembly, handling or repair of pneumatic systems should be performed by trained and experienced operators.. o not service machinery/equipment or attempt to remove components until safety is confirmed.. Inspection and maintenance of machinery/equipment should only be performed after confirmation of safe locked-out control positions.. When equipment is to be removed, confirm the safety process as mentioned above. ut the supply pressure for this equipment and exhaust all residual compressed air in the system.. efore machinery/equipment is restarted, take measures to prevent shooting-out of cylinder piston rod, etc. (leed air into the system gradually to create back pressure.) 4. ontact SM if the product is to be used in any of the following conditions:. onditions and environments beyond the given specifications, or if product is used outdoors.. Installation on equipment in conjunction with atomic energy, railway, air navigation, vehicles, medical equipment, food and beverages, recreation equipment, emergency stop circuits, press applications, or safety equipment.. n application which has the possibility of having negative effects on people, property, or animals, requiring special safety analysis. 5

Series N ctuator recautions e sure to read before handling. Warning esign. There is a possibiliy of danger of sudden action by air cylinders if sliding parts of machinery are twisted,due to external forces, etc. In such cases, human injury may occur; e.g., by catching hands or feet in the machinery, or damage to the machinery itself may occur. Therefore, the machine should be adjusted to operate smoothly and designed to avoid such dangers.. protective cover is recommeded to minimize the risk of personal injury. If a stationary object and moving parts of a cylinder are in close proximity, personal injury may occur. esign the structure to avoid contact with the human body.. Securely tighten all stationary parts and connected parts so that they will not become loose. specially when a cylinder operates with high frequency or is installed where there is a lot of vibration, ensure that all parts remain secure. 4. deceleration circuit or shock may be required. When a driven object is operated at high speed or the load is heavy, a cylinder s cushion will not be sufficient to absorb the impact. Install a deceleration circuit to reduce the speed before cushioning, or install an external shock absorber to relieve the impact. In this case, the rigidity of the machinery should also be examined. 5. onsider a possible drop in circuit pressure due to a power outage, etc. When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc. Therefore, safety equipment should be installed to prevent damage to machinery and/or human injury. Suspension mechanisms and lifting devices also require consideration for drop prevention. 6. onsider a possible loss of power source. Measures should be taken to protect against boduly injury and equipment damage in the event that there is a loss of power to equipment controlled by pneumatics, electricity or hydraulics, etc. 7. esign circuit that will prevent the driven object from shooting out. The driven object will shoot out at a high speed if one sde of the cylinder is pressurized after the air inside the cylinder is exhausted; for example, when the cylinder is driven with exhaust center directional control valves or when it is started after the residual pressure inside the circurt is exhausted. Such an event can possibly lead to bodily injury, by, for example catching in human limbs, or damge to the machinery. Threfore, slect equipment and design circuits to prevent shoot-outs. 8. onsider emergency stops. esign so that human injury and/or damage to machinery and equipment will not be caused when machinery is stopped by a safety device under abnormal conditions, a power outage or a manual emergency stop. 9. onsider the action when operation is restarted after an emergency stop or abnormal stop. esign the machinery so that human injury or equipment damage will not occur upon restart of operation. When the cylinder has to be reset at the starting position, install safe manual control equipment. Warning. heck the specifications. The products featured in this catalog are designed for used in industrial compressed air systems. If the products are used in conditions where pressure and /or temperature are outside range of specification, damage and/or malfunction may be occur. o not use in these conditions. (efer to specifications.) onsult SM if you use a fluid other than compressed air.. Intermediate stops When intermediate stopping of a cylinder piston is performed with a position closed center type directional control valve, it is difficult to achieve stopping positions as accurate and precise as with hydraulic pressure due to the compressibility of air. urthermore, since valves and cylinders, etc., are not guaranteed for zero air leakage, it may not be possible to hold a stopped position for an extended period of time. ontact SM in case it is necessary to hold a stopped position for an extended period. aution Selection. Operate within the limits of the maximum usable stroke. The piston rod will be damaged if operated beyond the maximum stroke. efer to the cylinder model selection procedure for the maximum useable stroke.. Operate the piston within a range such that collision damage will not occur at the stroke end. The operation range should prevent damage from occurring when a piston, having inertial force, stop by striking the cover at the stroke end. efer to the cylinder model selction prcedure for the maximum usable stroke.. Use a speed controller to adjust the cylinder drive speed, gradually increasing from a low speed to the desired speed setting. 4. rovide intermediate supports for long stroke cylinders. n intermediate support should be provided in orderto prevent damage to a cylinder having a long stroke, due to problems suc as sagging of the rod deflection of the cylinder tube. vibration adn external load. 5

Series N ctuator recautions e sure to read before handling. Mounting ushion aution. e certain to match the rod shaft center with the load and direction of movement when connecting. When not properly matched, problem may arise with the rod and tube, and damage may be caused due to friction on areas such as the inner tube surface, bushings, rod surface, and seals.. When an external guide is used, connect the rod end and the load in such a way that there is no interference at any point within the stroke.. o not scratch or gouge the sliding parts of the cylinder tube or piston rod by striking or grasping them with other objects. ylinder bores are manufactured to precise tolerances, so that even a slight deformation may cause faulty operation. Moveover scratches or gouges, etc., in the piston rod may lead to damaged seals and cause air leakage. 4. revent the seizure of rotating parts. revent the seizure of rotating parts (pins, etc.) by applying grease. 5. o not use until you can verify that equipment can operate properly. fter mounting, repairs, or modificatio, etc., connect the air supply and electric power, and then confirm proper mounting by measns of appropiate function and leak tests. 6. Instruction manual The product should be mounted and operated after thr instruction manual is thoroughly read and its conterns are undrstood. Keep the instruction manual where it can be referred to as needed.. reparation before piping efore piping is connected, it should be thoroughly blown out with air (flushing) or washed to remove chips, cutting oil and other debris from inside the pipe.. Wrapping of pipe tape When screwing together pipes and fittings, etc., be certain that chips from the pipe threads and sealing material do not get inside the piping. lso, when sealant tape is used, leave.5 to thread ridges exposed at the end of the threads. Wrapping direction Sealant tape aution. eadjust using the cushion needle. ushions are adjusted at the time of shipment, however, the cushion needle on the cover should be readjusted when the product is put into service, based upon factors such as the size of the load and the operating speed. When the cushion needle is turned clockwise, the restriction becomes smaller and the cushion's effectiveness is increased. Tighten the lock nut securely after adjustment is performed.. o not use the cushion needle fully closed. This will cause damage to the seals. Warning. Use clean air. o not use compressed air which includes chemicals, synthetic oils containing organic solvents, salt or corrosive gases, etc., as it can cause damage or malfunction. aution. Install air filters. Install air filters at the upstream side of valves. The filtration degree should be 5μm or finer.. Install an after cooler, air dryer or water separator, etc. ir that includes excessive drainage may cause malfunction of valves and other pneumatic equipment. To prevent this, install an after cooler, air dryer or water separator, etc.. Use the product within the specified range of fluid and ambient temperature. Take measures to prevent freezing, since moisture in circuits can be frozen under 5, and this may cause damage to seals and lead to malfunction. efer to SM s ir leaning quipment catalog for further details on compressed air quality. Maintenance Warning. emoval of equipment, and supply/exhaust of compressed air. efore any machinery or equipment is removed, forst ensure that the appropriate measures are in place to prevent the fall or erratic movement of driven objects and eqipment, ten cut off t electric power and reduce the pressure in thesystem to zero. Only then should you proceed with the removal of any machinery and equpment. When machinery is restarted, proceed with caution after confirming measures to prevent cylinder lurching. xpose approx. threads aution. rain flushing emove drainage from air filters regularly. (efer to specifications.) 54

Series N uto Switch recautions e sure to read before handling. Warning. onfirm the specifications. ead the specifications carefully and use this product appropriately. The product may be damaged or malfunction if it is used outside the range of specifications for current load, voltage, temperature or impact.. Take precautions when multiple cylinders are used close together. When multiple auto switch cylinders are used in close proximity, magnetic field interference may cause the switches to malfunction. Maintain a minimum cylinder separation of 4mm.. ay attention to the length of time that a switch is ON at an intermediate stroke position. When an auto switch is placed at an intermediate position of the stroke and a load is driven at the time the piston passes, the auto switch will operate, but if the speed is too great the operating time will be shortened and the load may not operate properly. The maximum detectable piston speed is: V (mm/s) = uto switch operating range (mm) x Time load applied (ms) 4. Keep wiring as short as possible. <eed switches> s the length of the wiring to a load gets longer, the rush current at switching ON becomes greater, and this may shorten the product s life. (The switch will stay ON all the time.) Use a contact protection box when the wire length is 5m or longer. <Solid state switches> lthough wire length should not affect switch function, use a wire m or shorter. 5. ay attention to the internal voltage drop of the switch. <eed switches> ) Switches with an indicator light (xcept -Z76) If auto switches are connected in series as shown below, take note that there will be a large voltage drop because of internal resistance in the light emitting diodes. (efer to internal voltage drop in the auto switch specifications.) [The voltage drop will be n times larger when n auto switches are connected.] ven though an auto switch operates normally, the load may not operate. Load esign & Selection Warning In the same way, when operating under a specified voltage, although an auto switch may operate normally, the load may not operate. Therefore, the formula below should be satisfied after confirming the minimum operating voltage of the load. Supply voltage Internal voltage > drop of switch Minimum operating voltage of load ) If the internal resistance of a light emitting diode causes a problem, select a switch without an indicator light (Model -Z8). <Solid state switches> ) enerally, the internal voltage drop will be greater with a wire solid state auto switch than with a reed switch. Take the same precautions as in ). lso, note that a V relay is not applicable. 6. ay attention to leakage current. <Solid state switches> With a wire solid state auto switch, current (leakage current) flows to the load to operate the internal circuit even when in the O state. Operating current of load (O condition) > Leakage current If the criteria given in the above formula are not met, it will not reset correctly (stays ON). Use a wire switch if this specification will not be satisfied. Moreover, leakage current flow to the load will be n times larger when n auto switches are connected in parallel. 7. o not use a load that generates surge voltage. <eed switches> If driving a load such as a relay that generates a surge voltage, use a contact protection box. <Solid state switches> lthough a zener diode for surge protection is connected at the output side of a solid state auto switch, damage may still occur if the surge is applied repeatedly. When a load, such as a relay or solenoid which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8. autions for use in an interlock circuit When an auto switch is used for an interlock signal requiring high reliability, devise a double interlock system to avoid trouble by providing a mechanical protection function, or by also using another switch (sensor) together with the auto switch. lso perform periodic maintenance and confirm proper operation. 9. nsure sufficient clearance for maintenance activities. When designing an application, be sure to allow sufficient clearance for maintenance and inspections. 55

Series N uto Switch recautions e sure to read before handling. Warning Mounting & djustment. o not drop or bump. o not drop, bump or apply excessive impacts (m/s² or more for reed switches and m/s² or more for solid state switches) while handling. lthough the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction.. o not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress.. Mount switches using the proper tightening torque. If a switch is tightened beyond the range of tightening torque, the mounting screws or switch may be damaged. On the other hand, tightening below the range of tightening torque may allow the switch to slip out of position. (efer to switch mounting instructions for each series for switch mounting, moving, and tightening torque, etc.) 4. Mount a switch at the center of the operating range. djust the mounting position of an auto switch so that the piston stops at the center of the operating range (the range in which a switch is ON). (The mounting position shown in the catalog indicates the optimum position at stroke end.) If mounted at the end of the operating range (around the borderline of ON and O), operation will be unstable. Warning Wiring. void repeatedly bending or stretching lead wires. roken lead wires will result from repeatedly applying bending stress or stretching force to the lead wires.. e sure to connect the load before power is applied. < wire type> If the power is turned ON when an auto switch is not connected to a load, the switch will be instantly damaged because of excess current.. onfirm proper insulation of wiring. e certain that there is no faulty wiring insulation (contact with other circuits, ground fault, improper insulation between terminals, etc.). amage may occur due to excess current flow into a switch. 4. o not wire with power lines or high voltage lines. Wire separately from power lines or high voltage lines, avoiding parallel wiring or wiring in the same conduit with these lines. ontrol circuits containing auto switches may malfunction due to noise from these other lines. Warning Wiring 5. o not allow short circuit of loads. <eed switches> If the power is turned ON with a load in a short circuited condition, the switch will be instantly damaged because of excess current flow into the switch. <Solid state switches> ll models of N output type switches do not have built-in short circuit protection circuits. Note that if a load is short circuited, the switch will be instantly damaged as in the case of reed switches. Take special care to avoid reverse wiring with the brown (red) power supply line and the black (white) output line on wire type switches. 6. void incorrect wiring. <eed switches> 4V switch with indicator light has polarity. The brown (red) lead wire is (+), and the blue (black) lead wire is ( ). ) If connections are reversed, a switch will operate, however, the light emitting diode will not light up. lso note that a current greater than that specified will damage a light emitting diode and it will no longer operate. pplicable models: -Z7 <Solid state switches> ) If connections are reversed on a wire type switch, the switch will not be damaged if protected by a protection circuit, but the switch will always stay in an ON state. However, it is still necessary to avoid reversed connections, since the switch could be damaged by a load short circuit in this condition. )If connections are reversed (power supply line + and power supply line ) on a wire type switch, the switch will be protected by a protection circuit. However, if the power supply line (+) is connected to the blue (black) wire and the power supply line ( ) is connected to the black (white) wire, the switch will be damaged. Lead wire color changes Lead wire colors of SM switches and related products have been changed in order to meet N (Nippon lectric ontrol quipment Industries ssociation) Standard 4 for production beginning September, 996 and thereafter. lease refer to the tables provided. Special care should be taken regarding wire polarity during the time that the old colors still coexist with the new colors. wire Output (+) Output ( ) Old ed lack Solid state with diagnostic output ower supply N Output iagnostic output Old ed lack White ellow New rown lue New rown lue lack Orange wire ower supply N Output Old ed lack White Solid state with latch type diagnostic output ower supply N Output Latch type diagnostic output Old ed lack White ellow New rown lue lack New rown lue lack Orange 56

Series N uto Switch recautions e sure to read before handling. Warning Operating nvironment. Never use in an atmosphere of explosive gases. The structure of auto switches is not intended to prevent explosion. Never use in an atmosphere with an explosive gas since this may cause a serious explosion.. o not use in an area where a magnetic field is generated. uto switches will malfunction or magnets inside cylinders will become demagnetized. (onsult SM regarding the availability of a magnetic field resistant auto switch.). o not use in an environment where the auto switch will be continually exposed to water. lthough switches satisfy I standard I67 construction (IS 9: watertight structure), do not use switches in applications where continually exposed to water splash or spray. oor insulation or swelling of the potting resin inside switches may cause malfunction. 4. o not use in an environment with oil or chemicals. onsult SM if auto switches will be used in an environment with coolant, cleaning solvent, various oils or chemicals. If auto switches are used under these conditions for even a short time, they may be adversely affected by improper insulation, malfunction due to swelling of the potting resin, or hardening of the lead wires. 5. o not use in an environment with temperature cycles. onsult SM if switches are used where there are temperature cycles other than normal temperature changes, as there may be adverse effects inside the switches. 6. o not use in an environment where there is excessive impact shock. <eed switches> When excessive impact (m/s or more) is applied to a reed switch during operation, the contact point will malfunction and generate or cut off a signal momentarily (ms or less). onsult SM regarding the need to use a solid state switch depending upon the environment. 7. o not use in an area where surges are generated. <Solid state switches> When there are units (solenoid type lifter, high frequency induction furnace, motor, etc.) which generate a large amount of surge in the area around cylinders with solid state auto switches, this may cause deterioration or damage to the switch. void sources of surge generation and disorganized lines. 8. void accumulation of iron waste or close contact with magnetic substances. When a large amount of iron waste such as machining chips or spatter is accumulated, or a magnetic substance (something attracted by a magnet) is brought into close proximity with an auto switch cylinder, it may cause the auto switch to malfunction due to a loss of the magnetic force inside the cylinder. Warning Maintenance. erform the following maintenance periodically in order to prevent possible danger due to unexpected auto switch malfunction. ) Secure and tighten switch mounting screws. If screws become loose or the mounting position is dislocated, retighten them after readjusting the mounting position. ) onfirm that there is no damage to lead wires. To prevent faulty insulation, replace switches or repair lead wires, etc., if damage is discovered. ) onfirm the lighting of the green light on the color indicator type switch. onfirm that the green L is on when stopped at the established position. If the red L is on, the mounting position is not appropriate. eadjust the mounting position until the green L lights up. Warning Other. onsult SM concerning water resistance, elasticity of lead wires, and usage at welding sites, etc. 57

Series N Medium uty ir ylinder Limited ylinder Warranty - Terms and onditions of Sale... SM warrants that for 8 months or 8 service miles*, whichever occurs first from date of purchase, it will replace or make adjustment at SM s option, of any defective cylinder sold if the cylinder product is returned with SM s prior written consent, transportation prepaid by the original buyer, and received by SM at its place of business within the warranty period. SM shall have the right to inspect, prior to return, at the buyer s facility, any products claimed to be defective. This warranty is limited exclusively to cylinder products which, in the opinion of SM, have not been subjected to modification, misuse, negligence, misapplication, repairs or alterations. amage caused by fire, theft, riot, explosion or acts of ods are excluded from this warranty. The foregoing constitutes the sole exclusive remedy of the buyer and the only liability of SM and is in lieu of any and all other warranties, expressed or implied, or statutory as to merchantability, fitness for purpose sold, description, quality, productiveness or any other matter. SM shall not be liable for loss of use, or profit, or special or consequential damages. SM assumes no responsibility for engineering technical advice pertaining to any manufactured item to which SM s products or goods have been attached. No agent, employee, distributor, or representative of SM has the authority to extend the scope of this warranty or to make any other promises, warranties or guarantees concerning the manufacture, sale or application of SM s products. *Service Miles = (inches/stroke) x ( strokes/cycle) x (no of cycles) x [ mile / 6,6 inches] 58

lobal Manufacturing, istribution and Service Network Worldwide Subsidiaries UO USTI SM neumatik mbh (ustria) LIUM SM neumatics N.V./S.. ULI SM Industrial utomation ulgaria OO OTI SM Industrijska utomatika d.o.o. ZH SM Industrial utomation Z s.r.o. NMK SM neumatik /S STONI SM neumatics stonia INLN SM neumatics inland O N SM neumatique S.. MN SM neumatik mbh K SM Hellas HUN SM Hungary Ipari utomatizálási Kft. ILN SM neumatics (Ireland) Ltd. ITL SM Italia S.p.. LTVI SM neumatics Latvia SI LITUV SM neumatics Lietuva, U NTHLNS SM neumatics V NOW SM neumatics Norway /S OLN SM Industrial utomation olska Sp.z.o.o. OMNI SM omania S.r.l. USSI SM neumatik LL. SLOVKI SM riemyselná utomatizáciá, s.r.o. SLOVNI SM Industrijska vtomatika d.o.o. SIN/OTUL SM spaña, S.. SWN SM neumatics Sweden SWITZLN SM neumatik UK SM neumatics (U.K.) Ltd. SI HIN SM (hina) o., Ltd. HON KON SM neumatics (Hong kong) Ltd. INI SM neumatics (India) vt. Ltd. N SM orporation MLSI SM neumatics (S...) Sdn. hd. HILIINS SM neumatics (hilippines), Inc. SINO SM neumatics (S...) te. Ltd. SOUTH KO SM neumatics Korea o., Ltd. TIWN SM neumatics (Taiwan) o., Ltd. THILN SM Thailand Ltd. NOTH MI N SM neumatics (anada) Ltd. MXIO SM orporation (Mexico) S...V. US SM orporation of merica SOUTH MI NTIN SM rgentina S.. OLIVI SM neumatics olivia S..L. ZIL SM neumaticos do razil Ltda. HIL SM neumatics (hile) S.. VNZUL SM Neumatica Venezuela S.. ONI USTLI SM neumatics (ustralia) ty. Ltd. NW ZLN SM neumatics (N.Z.) Ltd. U.S. & anadian Sales Offices ST tlanta oston harlotte Nashville New ersey ichmond ochester Tampa WST ustin allas Los ngeles hoenix ortland San rancisco Toronto MIWST hicago incinnati leveland etroit Indianapolis Milwaukee Minneapolis St. Louis N Montreal Tel: (54) 7-9595 ax: (54) 7-77 Toronto Tel: (95) 8-4 ax: (95) 8-8686 Vancouver Tel: (64) 57-646 ax: (64) 57-647 Windsor Tel: (59) 944-555 ax: (59) 944-87 Los ngeles Sales office & actory Sales office Indianapolis SM orporation of merica N. ranklin oad Indianapolis, IN 466 (8) 76-76 (SM.SM) www.smcusa.com SM neumatics (anada) Ltd. 6768 inancial rive Mississauga Ontario, L5N 76 anada (95) 8-4 www.smcpneumatics.ca or International inquires: www.smcworld.com 8 SM orporation of merica, ll ights eserved. ll reasonable efforts to ensure the accuracy of the information detailed in this catalog were made at the time of publishing. However, SM can in no way warrant the information herein contained as specifications are subject to change without notice. MU-M-

9- Series N ir ylinder N Interchangeable Large ore Size eatures Medium duty 5", 6" and 8" bores different N mounting options Standard with adjustable air cushion uto switch capable

Series N ylinder Large ore ontents page How to order uto Switches Specifications onstruction eplacement Kits 4 5 5 Mounting styles MX basic style MX tie rod extended - both ends MX tie rod extended - head end MX tie rod extended - rod cover end M rod side rectangular flange M head side rectangular flange L MS foot style MS side tapped style S MS4 side lug style X M double head clevis style M double detatchable head side clevis style imension hanges (X5, X Options) ccessories Warranty and recautions 6 6 7 7 8 8 9 9 4

Series N ylinder Large ore Minimum operating pressure Maximum operating pressure 8 psi (.6 Mpa) 5 psi (.75 Mpa) 4

9 8 7 9 8 5 6 7 4 4 6 5 omponent Material Qty. Note N 5 -S - od cover ushion valve luminum alloy olled steel nodized lectroless nickel plating ore 5 6 8 Special options Nil X5 X6 X7 X56 X57 Standard Oversized rod High temperature Low temperature Oversized W/ high temperature Oversized W/ low temperature 4 5 6 7 8 Snap ring ushion valve seal Head cover iston rod ushion ushion Spring steel N luminum alloy arbon steel luminum alloy luminum alloy hosphate coated nodized nodized nodized Seal kits include the following parts: - od seal - iston seal - land seal - ylinder tube gasket - ushion valve seal - rease pack - Loctite 4 * ushion seal is not included for X6, X56, X7, and X57 over ø5" bore 9 4 5 iston iston gasket Magnet iston seal Wear ring am nut land luminum alloy N - N esin olled steel luminum alloy () Nickel plating nodized 6 ushing omposite 7 ylinder tube luminum alloy Hard anodized N 5 ore 5 6 8-4 - 4 Stroke (In inches and hundredths) 8 9 Tie rod nut Tie rod od seal land seal ushion seal ylinder tube gasket olled steel arbon steel N N Urethane N 8 4 Nickel plated Zinc chromated N 5 ore 5 6 8 - - Special options Nil Standard X5 Oversized rod X5 oil scraper X55 Oversized W/ oil scraper N 5-6 - 4 - N 5 - - 4 Magnet Nil - Non-Magnet - With Magnet ore 5 6 8 Stroke (In inches and hundredths) Special options Nil X5 X6 X7 X56 X57 X Standard Oversized rod High temperature Low temperature Oversized W/ high temperature Oversized W/ low temperature Stainless steel piston rod Mounting L S X ore 5 6 8 Stroke (In inches and hundredths) Note: Tie rod length varies by mounting style. Quantity one set (4 pcs) of tie rods by mounting 5

Series N ylinder Large ore imension rawings MX - asic style () Ø 4- - TH Ø ØMM T Z + Stroke ore Size ØMM Ø L+ + T TH Z+ 5 (5"). -6. 5.8.5 /- 5.5 /NT 4.5.88 4..75.8 5.88 6 (6").75-4.6 6.9. /- 6.5 NT 5.. 4.88.5.6 6.6 8 (8").75-4.6 9.. -8 8.5 NT 5..5 6.44 4.5.6 6.75 MX - Tie rod extended - both ends () Ø 4- - TH Ø ØMM T Z + Stroke ore Size ØMM Ø L+ + T TH Z+ 5 (5"). -6. 5.8.5.8 /- 5.5 / NT 4.5.88 4..75.8 5.88 6 (6").75-4.6 6.9..8 /- 6.5 NT 5.. 4.88.5.6 6.6 8 (8").75-4.6 9... -8 8.5 NT 5..5 6.44 4.5.6 6.75 6

MX - Tie rod extended - head end () - Ø 4- TH Ø MM Z + Stroke T ore Size ØMM Ø L+ + T TH Z+ 5 (5"). -6. 5.8.5.8 /- / NT 5.5 4.5.88 4..75.8 5.88 6 (6").75-4.6 6.9..8 /- NT 6.5 5.. 4.88.5.6 6.6 8 (8").75-4.6 9... -8 NT 8.5 5..5 6.44 4.5.6 6.75 MX - Tie rod extended - rod cover end () Ø 4- - TH Ø MM T Z + Stroke ore Size ØMM Ø L+ + T TH Z+ 5 (5"). -6. 5.8.5.8 /- / NT 5.5 4.5.88 4..75.8 5.88 6 (6").75-4.6 6.9..8 /- NT 6.5 5.. 4.88.5.6 6.6 8 (8").75-4.6 9... -8 NT 8.5 5..5 6.44 4.5.6 6.75 7

Series N ylinder Large ore imension rawings M - od side rectangular flange () 4- Ø W - TH ØMM T U Z + Stroke ore Size ØMM Ø Ø L+ + T TH U W Z+ 5 (5"). -6..5 5.5 / NT.5 4.5.88 4. 6.6.75 7.6.75.8 5.88 6 (6").75-4.6. 6.5 NT.5 5.. 4.88 7.6.5 8.6.88.6 6.6 M - Head side rectangular flange () - 4- TH Ø ØMM L+ Stroke Z + Stroke Z + Stroke T U ore Size 5 (5") ØMM Ø Ø L+ + T TH U Z+ Z+. -6..5 5.5 / NT.5 4.5.88 4. 6.6.75 7.6.8 6.5 5.88 6 (6").75-4.6. 6.5 NT.5 5.. 4.88 7.6.5 8.6.6 7.8 6.6 8

MS - oot style (L) X+ Stroke - T H Ø ØMM S Ø O S + Stroke O ore Size ØMM Ø H O T Ø L+ + S S+ X+ 5 (5"). -6..6.75.6.9.5 5.5 / NT 4.5.88 4.5 7.88.8 7.5 6 (6").75-4.6.75.5.6.9. 6.5 NT 5.. 5.5 8.5.6 8. 8 (8").75-4.6.75 4.5.69.5. 8.5 NT 5..5 7. 8.75.6 8.56 MS - Side lug style (S) - ST LH Ø ØMM TS US ØS XS SS + Stroke ore Size ØMM TS Ø US ST L+ XS SS+ + LH 5 (5"). -6 6.88..5 8.5. / NT 4.5.6..88.75.8 6 (6").75-4 7.88.6. 9.5. NT 5...6..5.6 8 (8").75-4 9.88.6..5. NT 5...75.5 4.5.6 ØS.75.75.75 9

Series N ylinder Large ore imension rawings MS4 - Side tapped style () Ø 4- - X + Stroke - U M (MX) Ø ØMM TH Ø ØMM TN T 4-NT epth N XT SN + Stroke Z + Stroke ore Size 5 (5") 6 (6") 8 (8") ØMM..75.75-6 -4-4..6.6 5.8 6.9 9. Ø.5.. /- /- -8 5.5 6.5 8.5 /NT NT NT L+ 4.5 5. 5. N.75.88. NT - - - +.88..5 SN+.88..5 T 4. 4.88 6.44 TH.75.5 4.5 TN.68.5 4.5.8.6.6 XT.44.8.8 Z+ 5.88 6.6 6.75 M - ouble head clevis style (X) L TH (ØIN) ore Size 5 (5") 6 (6") ØMM Ø L+ L M + TH U X+. -6..5.8.75 5.5 / NT 4.5.94.95.88.75.5.8 7..75-4.6..5. 6.5 NT 5.....5..6 8. 8 (8").75-4.6..5. 8.5 NT 5....5 4.5..6 8.5 Note: ivot and cotter pins are included.

M - ouble detatchable head side clevis style () X + Stroke - U M MX Ø ØMM L TH (ØIN) ore Size ØMM Ø L+ L M + TH U X+ 5 (5"). -6..5.8.75 5.5 / NT.6 4.5.94.95.88.75.5.8 7.75 6 (6").75-4.6..5. 6.5 NT.75 5.....5..6 8.88 8 (8").75-4.6..5. 8.5 NT.75 5....5 4.5..6 9. Note: ivot and cotter pins are included. imension changes for Options Oversized rod (X5 Option) otated orts (X Option) ort standard location Head end Ø ØMM od end Z + Stroke How to Order: -X ort ushion ushion location standard ore Size ØMM Ø Z+ 5 (5").75-4.6..6 6. 6 (6").75 /4-..75.88 6.88 8 (8").75 /4-..75.88 7. Standard art Number Location. (=port, =cushion) vailable on standard, X5, X6, X7, X6, and X5 orts and cushions in same location on rod and head ends Standard available configurations: X, X, X, X, X, X, X, X, X orts and cushions NOT aligned between od and Head ends available via S xample: N5-4-X ( = port, = cushion) Ø 4-

Series N ylinder Large ore ye racket Ø M L Ø L M imensions art No. N-5 N-8 N- /4 / Note: ivot pin is not included 7/ / / / 4 / 5 L /4 L /4 / /8 M M /4.56.5.8 Weight (lbs). 5.8.4 levis racket Ø W W M L Ø M L imensions art No. N-5 N-8 N-.6 4.6 5.4 Note: ivot pin is not included. 9/6 /4 /6.65.55. W /- -8-8 / 4 / 5 L /4 L /6 /4 M M /6 Weight (lbs).79 5.45 9.89 od levis W W H Ø L Ø Tap through imensions art No. N-5 N-8 N-.65.55..75 /8 4 /8 Note: am nut, pivot, and cotter pins are included. H / W /4 / L /4 / /8-6 -4 /4- Weight (lbs).5.78 9.

lignment oupler Shank dia. cross flat /6 adial float H Spherical motion Ø imensions art No. N-5 N-8-6 -4 N- /4- / / 5/6 5/6 5/6 5/6 / / / /4 /4 H / /4 /4 ivot ins Ø L Ø L Ø imensions imensions art No. N-5 N-8 N- L /8 4 /8 art No. N-5 N-8 N-.4.4.7 L..6 4.66.7. 4.5 Note: etainer rings are included. Note: otter pins are included. od am Nut od ye Thread x Ø H Ø imensions imensions art No. M- M-8 M-.99.7.65 / H 7/64 5/64 / Thread -6UN -4UN /4-UN art No. NI-5 NI-8 NI- /6 /6 7/6 /4 / /6 9/6-6 -4 /4- Weight (lbs).9.4.7 imensions per SM 8.. 987 (999) Note: am nut is included.

Series N ylinder Large ore Series N Safety Instructions These safety instructions are intended to prevent a hazardous situation and/or equipment damage. These instructions indicate the level of potential hazard by a label of "aution", "Warning" or "anger". To ensure safety, be sure to observe ISO 444 Note ), IS 87 Note ) and other safety practices. aution : Operator error could result in injury or equipment damage. Warning : Operator error could result in serious injury or loss of life. anger : In extreme conditions, there is a possible result of serious injury or loss of life. Note ) ISO 444: neumatic fluid power -- ecommendations for the application of equipment to transmission and control systems Note ) IS 87: eneral ules for neumatic quipment Warning. The compatibility of pneumatic equipment is the responsibility of the person who designs the pneumatic system or decides its specifications. Since the products specified here are used in various operating conditions, their compatibility for the specific pneumatic system must be based on specifications or after analysis and/or tests to meet your specific requirements.. Only trained personnel should operate pneumatically operated machinery and equipment. ompressed air can be dangerous if handled incorrectly. ssembly, handling or repair of pneumatic systems should be performed by trained and experienced operators.. o not service machinery/equipment or attempt to remove components until safety is confirmed.. Inspection and maintenance of machinery/equipment should only be performed after confirmation of safe locked-out control positions.. When equipment is to be removed, confirm the safety process as mentioned above. ut the supply pressure for this equipment and exhaust all residual compressed air in the system.. efore machinery/equipment is restarted, take measures to prevent shooting-out of cylinder piston rod, etc. (leed air into the system gradually to create back pressure.) 4. ontact SM if the product is to be used in any of the following conditions:. onditions and environments beyond the given specifications, or if product is used outdoors.. Installation on equipment in conjunction with atomic energy, railway, air navigation, vehicles, medical equipment, food and beverages, recreation equipment, emergency stop circuits, press applications, or safety equipment.. n application which has the possibility of having negative effects on people, property, or animals, requiring special safety analysis. 4

Series N ctuator recautions e sure to read before handling. Warning esign. There is a possibiliy of danger of sudden action by air cylinders if sliding parts of machinery are twisted,due to external forces, etc. In such cases, human injury may occur; e.g., by catching hands or feet in the machinery, or damage to the machinery itself may occur. Therefore, the machine should be adjusted to operate smoothly and designed to avoid such dangers.. protective cover is recommeded to minimize the risk of personal injury. If a stationary object and moving parts of a cylinder are in close proximity, personal injury may occur. esign the structure to avoid contact with the human body.. Securely tighten all stationary parts and connected parts so that they will not become loose. specially when a cylinder operates with high frequency or is installed where there is a lot of vibration, ensure that all parts remain secure. 4. deceleration circuit or shock may be required. When a driven object is operated at high speed or the load is heavy, a cylinder s cushion will not be sufficient to absorb the impact. Install a deceleration circuit to reduce the speed before cushioning, or install an external shock absorber to relieve the impact. In this case, the rigidity of the machinery should also be examined. 5. onsider a possible drop in circuit pressure due to a power outage, etc. When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc. Therefore, safety equipment should be installed to prevent damage to machinery and/or human injury. Suspension mechanisms and lifting devices also require consideration for drop prevention. 6. onsider a possible loss of power source. Measures should be taken to protect against boduly injury and equipment damage in the event that there is a loss of power to equipment controlled by pneumatics, electricity or hydraulics, etc. 7. esign circuit that will prevent the driven object from shooting out. The driven object will shoot out at a high speed if one sde of the cylinder is pressurized after the air inside the cylinder is exhausted; for example, when the cylinder is driven with exhaust center directional control valves or when it is started after the residual pressure inside the circurt is exhausted. Such an event can possibly lead to bodily injury, by, for example catching in human limbs, or damge to the machinery. Threfore, slect equipment and design circuits to prevent shoot-outs. 8. onsider emergency stops. esign so that human injury and/or damage to machinery and equipment will not be caused when machinery is stopped by a safety device under abnormal conditions, a power outage or a manual emergency stop. 9. onsider the action when operation is restarted after an emergency stop or abnormal stop. esign the machinery so that human injury or equipment damage will not occur upon restart of operation. When the cylinder has to be reset at the starting position, install safe manual control equipment. Warning. heck the specifications. The products featured in this catalog are designed for used in industrial compressed air systems. If the products are used in conditions where pressure and /or temperature are outside range of specification, damage and/or malfunction may be occur. o not use in these conditions. (efer to specifications.) onsult SM if you use a fluid other than compressed air.. Intermediate stops When intermediate stopping of a cylinder piston is performed with a position closed center type directional control valve, it is difficult to achieve stopping positions as accurate and precise as with hydraulic pressure due to the compressibility of air. urthermore, since valves and cylinders, etc., are not guaranteed for zero air leakage, it may not be possible to hold a stopped position for an extended period of time. ontact SM in case it is necessary to hold a stopped position for an extended period. aution Selection. Operate within the limits of the maximum usable stroke. The piston rod will be damaged if operated beyond the maximum stroke. efer to the cylinder model selection procedure for the maximum useable stroke.. Operate the piston within a range such that collision damage will not occur at the stroke end. The operation range should prevent damage from occurring when a piston, having inertial force, stop by striking the cover at the stroke end. efer to the cylinder model selction prcedure for the maximum usable stroke.. Use a speed controller to adjust the cylinder drive speed, gradually increasing from a low speed to the desired speed setting. 4. rovide intermediate supports for long stroke cylinders. n intermediate support should be provided in orderto prevent damage to a cylinder having a long stroke, due to problems suc as sagging of the rod deflection of the cylinder tube. vibration adn external load. 5

Series N ylinder Large ore Series N ctuator recautions e sure to read before handling. aution Mounting. e certain to match the rod shaft center with the load and direction of movement when connecting. When not properly matched, problem may arise with the rod and tube, and damage may be caused due to friction on areas such as the inner tube surface, bushings, rod surface, and seals.. When an external guide is used, connect the rod end and the load in such a way that there is no interference at any point within the stroke.. o not scratch or gouge the sliding parts of the cylinder tube or piston rod by striking or grasping them with other objects. ylinder bores are manufactured to precise tolerances, so that even a slight deformation may cause faulty operation. Moveover scratches or gouges, etc., in the piston rod may lead to damaged seals and cause air leakage. 4. revent the seizure of rotating parts. revent the seizure of rotating parts (pins, etc.) by applying grease. 5. o not use until you can verify that equipment can operate properly. fter mounting, repairs, or modificatio, etc., connect the air supply and electric power, and then confirm proper mounting by measns of appropiate function and leak tests. 6. Instruction manual The product should be mounted and operated after thr instruction manual is thoroughly read and its conterns are undrstood. Keep the instruction manual where it can be referred to as needed.. reparation before piping efore piping is connected, it should be thoroughly blown out with air (flushing) or washed to remove chips, cutting oil and other debris from inside the pipe.. Wrapping of pipe tape When screwing together pipes and fittings, etc., be certain that chips from the pipe threads and sealing material do not get inside the piping. lso, when sealant tape is used, leave.5 to thread ridges exposed at the end of the threads. Wrapping direction xpose approx. threads Sealant tape aution ushion. eadjust using the cushion needle. ushions are adjusted at the time of shipment, however, the cushion needle on the cover should be readjusted when the product is put into service, based upon factors such as the size of the load and the operating speed. When the cushion needle is turned clockwise, the restriction becomes smaller and the cushion's effectiveness is increased. Tighten the lock nut securely after adjustment is performed.. o not use the cushion needle fully closed. This will cause damage to the seals. Warning. Use clean air. o not use compressed air which includes chemicals, synthetic oils containing organic solvents, salt or corrosive gases, etc., as it can cause damage or malfunction. aution. Install air filters. Install air filters at the upstream side of valves. The filtration degree should be 5µm or finer.. Install an after cooler, air dryer or water separator, etc. ir that includes excessive drainage may cause malfunction of valves and other pneumatic equipment. To prevent this, install an after cooler, air dryer or water separator, etc.. Use the product within the specified range of fluid and ambient temperature. Take measures to prevent freezing, since moisture in circuits can be frozen under 5, and this may cause damage to seals and lead to malfunction. efer to SM s ir leaning quipment catalog for further details on compressed air quality. Maintenance Warning. emoval of equipment, and supply/exhaust of compressed air. efore any machinery or equipment is removed, forst ensure that the appropriate measures are in place to prevent the fall or erratic movement of driven objects and eqipment, ten cut off t electric power and reduce the pressure in thesystem to zero. Only then should you proceed with the removal of any machinery and equpment. When machinery is restarted, proceed with caution after confirming measures to prevent cylinder lurching. aution. rain flushing emove drainage from air filters regularly. (efer to specifications.) 6

Series N uto Switch recautions e sure to read before handling. Warning. onfirm the specifications. ead the specifications carefully and use this product appropriately. The product may be damaged or malfunction if it is used outside the range of specifications for current load, voltage, temperature or impact.. Take precautions when multiple cylinders are used close together. When multiple auto switch cylinders are used in close proximity, magnetic field interference may cause the switches to malfunction. Maintain a minimum cylinder separation of 4mm.. ay attention to the length of time that a switch is ON at an intermediate stroke position. When an auto switch is placed at an intermediate position of the stroke and a load is driven at the time the piston passes, the auto switch will operate, but if the speed is too great the operating time will be shortened and the load may not operate properly. The maximum detectable piston speed is: V (mm/s) = uto switch operating range (mm) x Time load applied (ms) 4. Keep wiring as short as possible. <eed switches> s the length of the wiring to a load gets longer, the rush current at switching ON becomes greater, and this may shorten the product s life. (The switch will stay ON all the time.) Use a contact protection box when the wire length is 5m or longer. <Solid state switches> lthough wire length should not affect switch function, use a wire m or shorter. 5. ay attention to the internal voltage drop of the switch. <eed switches> ) Switches with an indicator light (xcept -Z76) If auto switches are connected in series as shown below, take note that there will be a large voltage drop because of internal resistance in the light emitting diodes. (efer to internal voltage drop in the auto switch specifications.) [The voltage drop will be n times larger when n auto switches are connected.] ven though an auto switch operates normally, the load may not operate. Load esign & Selection Warning In the same way, when operating under a specified voltage, although an auto switch may operate normally, the load may not operate. Therefore, the formula below should be satisfied after confirming the minimum operating voltage of the load. Supply voltage Internal voltage > drop of switch Minimum operating voltage of load ) If the internal resistance of a light emitting diode causes a problem, select a switch without an indicator light (Model -Z8). <Solid state switches> ) enerally, the internal voltage drop will be greater with a wire solid state auto switch than with a reed switch. Take the same precautions as in ). lso, note that a V relay is not applicable. 6. ay attention to leakage current. <Solid state switches> With a wire solid state auto switch, current (leakage current) flows to the load to operate the internal circuit even when in the O state. Operating current of load (O condition) > Leakage current If the criteria given in the above formula are not met, it will not reset correctly (stays ON). Use a wire switch if this specification will not be satisfied. Moreover, leakage current flow to the load will be n times larger when n auto switches are connected in parallel. 7. o not use a load that generates surge voltage. <eed switches> If driving a load such as a relay that generates a surge voltage, use a contact protection box. <Solid state switches> lthough a zener diode for surge protection is connected at the output side of a solid state auto switch, damage may still occur if the surge is applied repeatedly. When a load, such as a relay or solenoid which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8. autions for use in an interlock circuit When an auto switch is used for an interlock signal requiring high reliability, devise a double interlock system to avoid trouble by providing a mechanical protection function, or by also using another switch (sensor) together with the auto switch. lso perform periodic maintenance and confirm proper operation. 9. nsure sufficient clearance for maintenance activities. When designing an application, be sure to allow sufficient clearance for maintenance and inspections. 7

Series N ylinder Large ore Series N uto Switch recautions e sure to read before handling. Warning Mounting & djustment. o not drop or bump. o not drop, bump or apply excessive impacts (m/s or more for reed switches and m/s or more for solid state switches) while handling. lthough the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction.. o not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress.. Mount switches using the proper tightening torque. If a switch is tightened beyond the range of tightening torque, the mounting screws or switch may be damaged. On the other hand, tightening below the range of tightening torque may allow the switch to slip out of position. (efer to switch mounting instructions for each series for switch mounting, moving, and tightening torque, etc.) 4. Mount a switch at the center of the operating range. djust the mounting position of an auto switch so that the piston stops at the center of the operating range (the range in which a switch is ON). (The mounting position shown in the catalog indicates the optimum position at stroke end.) If mounted at the end of the operating range (around the borderline of ON and O), operation will be unstable. Warning Wiring. void repeatedly bending or stretching lead wires. roken lead wires will result from repeatedly applying bending stress or stretching force to the lead wires.. e sure to connect the load before power is applied. < wire type> If the power is turned ON when an auto switch is not connected to a load, the switch will be instantly damaged because of excess current.. onfirm proper insulation of wiring. e certain that there is no faulty wiring insulation (contact with other circuits, ground fault, improper insulation between terminals, etc.). amage may occur due to excess current flow into a switch. 4. o not wire with power lines or high voltage lines. Wire separately from power lines or high voltage lines, avoiding parallel wiring or wiring in the same conduit with these lines. ontrol circuits containing auto switches may malfunction due to noise from these other lines. Warning Wiring 5. o not allow short circuit of loads. <eed switches> If the power is turned ON with a load in a short circuited condition, the switch will be instantly damaged because of excess current flow into the switch. <Solid state switches> ll models of N output type switches do not have built-in short circuit protection circuits. Note that if a load is short circuited, the switch will be instantly damaged as in the case of reed switches. Take special care to avoid reverse wiring with the brown (red) power supply line and the black (white) output line on wire type switches. 6. void incorrect wiring. <eed switches> 4V switch with indicator light has polarity. The brown (red) lead wire is (+), and the blue (black) lead wire is ( ). ) If connections are reversed, a switch will operate, however, the light emitting diode will not light up. lso note that a current greater than that specified will damage a light emitting diode and it will no longer operate. pplicable models: -Z7 <Solid state switches> ) If connections are reversed on a wire type switch, the switch will not be damaged if protected by a protection circuit, but the switch will always stay in an ON state. However, it is still necessary to avoid reversed connections, since the switch could be damaged by a load short circuit in this condition. )If connections are reversed (power supply line + and power supply line ) on a wire type switch, the switch will be protected by a protection circuit. However, if the power supply line (+) is connected to the blue (black) wire and the power supply line ( ) is connected to the black (white) wire, the switch will be damaged. Lead wire color changes Lead wire colors of SM switches and related products have been changed in order to meet N (Nippon lectric ontrol quipment Industries ssociation) Standard 4 for production beginning September, 996 and thereafter. lease refer to the tables provided. Special care should be taken regarding wire polarity during the time that the old colors still coexist with the new colors. wire wire Output (+) Output ( ) Old ed lack Solid state with diagnostic output ower supply N Output iagnostic output Old ed lack White ellow New rown lue New rown lue lack Orange ower supply N Output Old ed lack White Solid state with latch type diagnostic output ower supply N Output Latch type diagnostic output Old ed lack White ellow New rown lue lack New rown lue lack Orange 8

Series N uto Switch recautions e sure to read before handling. Warning Operating nvironment. Never use in an atmosphere of explosive gases. The structure of auto switches is not intended to prevent explosion. Never use in an atmosphere with an explosive gas since this may cause a serious explosion.. o not use in an area where a magnetic field is generated. uto switches will malfunction or magnets inside cylinders will become demagnetized. (onsult SM regarding the availability of a magnetic field resistant auto switch.). o not use in an environment where the auto switch will be continually exposed to water. lthough switches satisfy I standard I67 construction (IS 9: watertight structure), do not use switches in applications where continually exposed to water splash or spray. oor insulation or swelling of the potting resin inside switches may cause malfunction. 4. o not use in an environment with oil or chemicals. onsult SM if auto switches will be used in an environment with coolant, cleaning solvent, various oils or chemicals. If auto switches are used under these conditions for even a short time, they may be adversely affected by improper insulation, malfunction due to swelling of the potting resin, or hardening of the lead wires. 5. o not use in an environment with temperature cycles. onsult SM if switches are used where there are temperature cycles other than normal temperature changes, as there may be adverse effects inside the switches. 6. o not use in an environment where there is excessive impact shock. <eed switches> When excessive impact (m/s or more) is applied to a reed switch during operation, the contact point will malfunction and generate or cut off a signal momentarily (ms or less). onsult SM regarding the need to use a solid state switch depending upon the environment. 7. o not use in an area where surges are generated. <Solid state switches> When there are units (solenoid type lifter, high frequency induction furnace, motor, etc.) which generate a large amount of surge in the area around cylinders with solid state auto switches, this may cause deterioration or damage to the switch. void sources of surge generation and disorganized lines. 8. void accumulation of iron waste or close contact with magnetic substances. When a large amount of iron waste such as machining chips or spatter is accumulated, or a magnetic substance (something attracted by a magnet) is brought into close proximity with an auto switch cylinder, it may cause the auto switch to malfunction due to a loss of the magnetic force inside the cylinder. Warning Maintenance. erform the following maintenance periodically in order to prevent possible danger due to unexpected auto switch malfunction. ) Secure and tighten switch mounting screws. If screws become loose or the mounting position is dislocated, retighten them after readjusting the mounting position. ) onfirm that there is no damage to lead wires. To prevent faulty insulation, replace switches or repair lead wires, etc., if damage is discovered. ) onfirm the lighting of the green light on the color indicator type switch. onfirm that the green L is on when stopped at the established position. If the red L is on, the mounting position is not appropriate. eadjust the mounting position until the green L lights up. Warning Other. onsult SM concerning water resistance, elasticity of lead wires, and usage at welding sites, etc. 9

Limited warranty and isclaimer/ompliance equirements The product used is subject to the following Limited warranty and isclaimer and ompliance equirements. ead and accept them before using the product. Limited warranty and isclaimer. The warranty period of the product is year in service or.5 years after the product is delivered, whichever is first. Note) lso, the product may have specified durability, running distance or replacement parts. lease consult your nearest sales branch.. or any failure or damage reported within the warranty period which is clearly our responsibility, a replacement product or necessary parts will be provided. This limited warranty applies only to our product independently, and not to any other damage incurred due to the failure of the product.. rior to using SM products, please read and understand the warranty terms and disclaimers noted in the specified catalog for the particular products. Note) Vacuum pads are excluded from this year warranty. vacuum pad is a consumable part, so it is warranted for a year after it is delivered. lso, even within the warranty period, the wear of a product due to the use of the vacuum pad or failure due to the deterioration of rubber material are not covered by the limited warranty. ompliance equirements. The use of SM products with production equipment for the manufacture of weapons of mass destruction (WM) or any other weapon is strictly prohibited.. The exports of SM products or technology from one country to another are governed by the relevant security laws and regulations of the countries involved in the transaction. rior to the shipment of an SM product to another country, assure that all local rules governing that export are known and followed. SM orporation of merica SM lvd., Noblesville, IN 466 www.smcusa.com SM neumatics (anada) Ltd. www.smcpneumatics.ca (8) SM.SM (76-76) e-mail: sales@smcusa.com or International inquiries: www.smcworld.com 5 SM orporation of merica, ll ights eserved. ll reasonable efforts to ensure the accuracy of the information detailed in this catalog were made at the time of publishing. However, SM can in no way warrant the information herein contained as specifications are subject to change without notice.