Type 1, 3, & 3R Enclosures

Transcription

1 Junction oxes Type 1 Screw over Junction oxes Type 1 Hinge over Junction oxes Type 3R Screw over Junction oxes Type 3R Hinge over Junction oxes Type 3 Screw over Gasketed Junction oxes Type 3 Weatherproof Screw over Panel Enclosures Type 1 Small Panel Enclosures Type 1 Medium Panel Enclosures Type 1 Large Panel Enclosures Type 1 Locking Hinge over w/perforated Panel Panel Enclosures Type 3R Small ontinuous Hinge over Panel Enclosures Type 3R Large ontinuous Hinge over Panel Enclosures Type 3R Double-Door Utility abinets Type 1 Telephone abinets Utility abinets Type 3R Telephone abinets Utility abinets Type 3R Screw over urrent Transformer abinets Utility abinets Type 3R Hinge over urrent Transformer abinets

2 Junction oxes Type 1 Screw over - Painted & Galvanized Data and Illustration Sheet Finish Wash and phosphate undercoat or galvanized steel NSI 61 gray acrylic electrocoat finish pplication Used as wiring boxes, junction and pull boxes Protects against contact with enclosed equipment Standards UL 50 listed, Type 1 S 22.2 No. 40 certified, Type 1 onforms to NEM standard for Type 1 ccessories Ground lug kit Touch-up paint See ccessories section onstruction Enclosure and cover are fabricated from code gauge steel or galvanized steel, (see table) Enclosure body has mounting holes on the back Enclosures are available with or without knockouts on the sides, top and bottom ends over is secured to the body with plated hex head combo screws Keyhole slots provided in the cover allow easy access to the inside without removing the screws #10-32 tapped hole provision for optional ground lug kit Discount Schedule: 2 Subclass: N0 & X1 (**) (25) (25) (**).25 (6) mounting hole (4PL) knockout area (see table for pattern, see detail for size) Front View Side View knockout area (see table for pattern, see detail for size) Dimensions: ** = (-1.90) if 16 or 14 gauge (-3.90) if 12 gauge ** = (-2.00) if 16 or 14 gauge (-4.00) if 12 gauge ottom View Notes: ooper -Line can provide special sizes, finishes and other modifications. onsult the factory for your special requirements. Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice. 50

3 Junction oxes Type 1 Screw over - Painted & Galvanized atalog Number Enclosure atalog Number Enclosure Size Knockout Knockout Pattern Pattern Painted Galvanized Height x Width x Depth x x KO No KO KO No KO in. mm Gauge Each Side Top & ottom 443 S 443 S NK 443 SGV 443 SGV NK 4.00 x 4.00 x x 102 x D D 444 S 444 S NK 444 SGV 444 SGV NK 4.00 x 4.00 x x 102 x D D 644 S 644 S NK 644 SGV 644 SGV NK 6.00 x 4.00 x x 102 x D E D 663 S 663 S NK 663 SGV 663 SGV NK 6.00 x 6.00 x x 152 x D E D E 664 S 664 S NK 664 SGV 664 SGV NK 6.00 x 6.00 x x 152 x D E D E 863 S 863 S NK 863 SGV 863 SGV NK 8.00 x 6.00 x x 152 x D E 864 S 864 S NK 864 SGV 864 SGV NK 8.00 x 6.00 x x 152 x D E 884 S 884 S NK 884 SGV 884 SGV NK 8.00 x 8.00 x x 203 x S NK SGV NK x 6.00 x x 152 x S 1084 S NK 1084 SGV 1084 SGV NK x 8.00 x x 203 x S S NK SGV SGV NK x x x 254 x S 1264 S NK SGV NK x 6.00 x x 152 x D E 1284 S 1284 S NK 1284 SGV 1284 SGV NK x 8.00 x x 203 x S S NK SGV SGV NK x x x 254 x S S NK SGV SGV NK x x x 305 x S NK SGV x x x 381 x I I S S NK SGV SGV NK x x x 305 x I S S NK SGV x x x 406 x I I S S NK SGV SGV NK x x x 305 x I J S NK SGV x x x 381 x I J I S S NK SGV SGV NK x x x 457 x I J I J S S NK SGV x x x 305 x I J S NK SGV x x x 457 x I J I J S S NK SGV SGV NK x x x 610 x I J I J S NK SGV SGV NK x x x 457 x I J I J S S NK SGV SGV NK x x x 610 x I J I J S NK SGV NK x x x 762 x (47) 1.87 (47) 3 /4-1 D 3 /4-1 E F /4 G H 3 /4-1 I J 3 /4-1 K onduit Sizes Knockout Detail Note: See table for applicable knockout pattern. 51

4 Junction oxes Type 1 Screw over - Painted & Galvanized atalog Number Enclosure atalog Number Enclosure Size Knockout Knockout Painted Galvanized Height x Width x Depth Pattern Pattern x x KO No KO KO No KO in. mm Gauge Each Side Top & ottom 666 S 666 S NK 666 SGV 666 SGV NK 6.00 x 6.00 x x 152 x D E D E 866 S 866 S NK 866 SGV 866 SGV NK 8.00x 6.00 x x 152 x D E 886 S 886 S NK 886 SGV 886 SGV NK 8.00 x 8.00 x x 203 x S 1086 S NK 1086 SGV 1086 SGV NK x 8.00 x x 203 x S S NK SGV SGV NK x x x 254 x S NK x 6.00 x x 152 x S NK SGV NK x 8.00 x x 203 x S S NK SGV SGV NK x x x 254 x S S NK SGV SGV NK x x x 305 x S NK SGV NK x x x 381 x S S NK SGV SGV NK x x x 305 x I S S NK SGV SGV NK x x x 406x I I J S S NK SGV SGV NK x x x 305x I J S NK SGV NK x x x 381x S S NK SGV SGV NK x x x 457x I J I J S NK SGV NK x x x 305x S S NK SGV SGV NK x x x 457x I J I J S NK SGV NK x x x 508x S S NK SGV SGV NK x x x 610x I J I J S NK SGV NK x x x 457 x S S NK SGV SGV NK x x x 610 x I J I J S NK SGV NK x x x 762 x S S NK SGV NK x x x 310 x I J I J S NK SGV NK x x x 762 x S NK SGV NK x x x 914 x S NK SGV NK x x x 914 x S NK SGV NK x x x 1219 x S 888 S NK 888 SGV 888 SGV NK 8.00 x 8.00 x x 203 x S NK SGV NK x x x 254 x S S NK SGV NK x x x 305 x S S NK SGV NK x x x 305 x I S S NK SGV NK x x x 305 x I J S S NK SGV NK x x x 457 x I J I J S S NK SGV NK x x x 305 x I J S S NK SGV NK x x x 457 x I J I J S NK SGV NK x x x 508 x S S NK SGV NK x x x 610 x I J I J S S NK SGV SGV NK x x x 610 x I J I J S NK SGV NK x x x 762 x S S NK SGV NK x x x 610 x I J I J S NK SGV NK x x x 762 x (47) 1.87 (47) 1 /2-3 /4 3 /4-1 1 /2-3 /4 D 3 /4-1 E 1 /2-3 /4 F /4 G 1 /2-3 /4 onduit Sizes Knockout Detail - Note: See table for applicable knockout pattern. 52 H 3 /4-1 I 1 /2-3 /4 J 3 /4-1 K 1 /2-3 /4

5 Junction oxes Type 1 Screw over - Painted & Galvanized atalog Number Enclosure atalog Number Enclosure Size Knockout Knockout Painted Galvanized Height x Width x Depth x x Pattern Pattern KO No KO KO No KO in. mm Gauge Each Side Top & ottom S NK SGV NK x x x 305 x S S NK SGV NK x x x 305 x I J S S NK SGV NK x x x 457 x I J I J S NK SGV NK x x x 305 x S S NK SGV NK x x x 457 x I J I J S S NK SGV NK x x x 610 x I J I J S NK SGV NK x x x 610 x S NK SGV NK x x x 762 x S NK SGV NK x x x 610x x S NK SGV NK x x x 914 x S NK SGV NK x x x 305 x S S NK SGV NK x x x 457 x I J I J S S NK SGV NK x x x 305 x I J S S NK SGV NK x x x 457 x I J I J S S NK SGV NK x x x 610 x I J I J S S NK SGV NK x x x 610 x I J I J S NK SGV NK x x x 762 x S S NK SGV NK x x `14 x 610 x I J I J S NK SGV NK x x x 1219 x S NK SGV NK x x x 1219 x S NK x x x 762 x S NK SGV NK x x x 1219 x S NK SGV NK x x x 1219 x Type 1 Flush & Surface overs - Painted & Galvanized atalog Number Discount Schedule: 2 Subclass: N0 Optional Flush over Fits Replacement Surface over Fits Flush overs Size Enclosure Surface overs Size Enclosure atalog Number x atalog Number x Painted Galvanized in. mm in. mm Gauge Painted Galvanized in. mm in. mm Gauge 44 SF x x x x SF x x x x SS x x x x SF x x x x SF x x x x SS x x x x SF x x x x SF x x x x SS x x x x SF x x x x SF x x x x SS x x x x SF x x x x SF x x x x SF x x x x SS x x x x SF x x x x SF x x x x SS x x x x

6 Junction oxes Type 1 Hinge over Data Sheet and atalog Number Finish Wash and phosphate undercoat NSI 61 gray acrylic electrocoat finish pplication Used as wiring boxes, junction and pull boxes Protects against contact with enclosed equipment Standards UL 50 listed, Type 1 S 22.2 No. 40 certified, Type 1 onforms to NEM standard for Type 1 ccessories Ground lug kit Touch-up paint See ccessories section onstruction Enclosure and cover are fabricated from (16) gauge steel Enclosure body has mounting holes on the back Enclosures are available with or without knockouts on the sides, top and bottom ends Removable cover is secured to the body with T-Slot hinges on one side and a friction dimple catch on the opposite side over is furnished with a recessed pull ring for opening convenience #10-32 tapped hole provision for optional ground lug kit Discount Schedule: 2 Subclass: O0 Enclosure Enclosure Size Knockout Knockout atalog Number Height x Width x Depth Pattern Pattern x x KO No KO in. mm Each Side Top & ottom 664 H 664 H NK 6.00 x 6.00 x x 152 x H 864 H NK 8.00 x 6.00 x x 152 x H 884 H NK 8.00 x 8.00 x x x 203 x H 1084 H NK x 8.00 x x 203 x H H NK x x x 254 x H 1284 H NK x 8.00 x x 203 x H H NK x x x 254 x H H NK x x x 305 x H H NK x x x 305 x H 666 H NK 6.00 x 6.00 x x 152 x H 886 H NK 8.00 x 8.00 x x 203 x H 1086 H NK x 8.00 x x 203 x H H NK x x x 254 x H H NK x x x 254 x H H NK x x x 305 x H H NK x x x 305 x H H NK x x x 406 x H H NK x x x 305 x H H NK x x x 457 x H H NK x x x 457 x H H NK x x x 610 x H H NK x x x 610 x H H NK x x x 610 x H H NK x x x 610 x 203 D E D E D E I J D E D E I I I I J I J I J I J I J I J I J I J I J I J I J I J I J Notes: ooper -Line can provide special sizes, finishes and other modifications. onsult the factory for your special requirements. Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice. 54

7 Junction oxes Type 1 Hinge over Illustration Sheet (51) pull ring friction dimple knockout area (see table for pattern, see detail for size) (51) Front View.25 (6) mounting hole (4PL) Side View T-Slot hinge knockout area (see table for pattern, see detail for size) ottom View 1.87 (47) 1.87 (47) 3 /4-1 D 3 /4-1 E F /4 G H 3 /4-1 I J 3 /4-1 K onduit Sizes Knockout Detail Note: See table for applicable knockout pattern. 55

8 Junction oxes Type 3R Screw over - Painted & Galvanized Data and Illustration Sheet pplication Used as wiring boxes, junction and pull boxes Protects against falling rain, sleet and external ice formation ccessories Touch-up paint See ccessories section onstruction Enclosure and cover are fabricated from code gauge galvaneal steel for painted or galvanized steel, (see table, page 57) Enclosure body has embossed mounting holes on the back vailable with or without knockouts on the bottom end of enclosures less than 30 inches wide over is held secure by sliding it under the top end flange and fastening it with plated screws on the bottom end flange, (larger sizes use two studs and wing nuts) Discount Schedule: 2 Subclass: S0 & Z60 Standards UL 50 listed, Type 3R S 22.2 No. 40 certified, Type 3R onforms to NEM standard for Type 3R E Finish Wash and phosphate undercoat NSI 61 gray acrylic electrocoat finish D knockout area (see table for pattern, see detail for size) ottom View 1.87 (47) 1.87 (47) Front View.25 (6) mounting hole (4PL) 3 /4-1 D 3 /4-1 E F /4 G H 3 /4-1 I J 3 /4-1 K onduit Sizes Knockout Detail Note: See table for applicable knockout pattern. Notes: ooper -Line can provide special sizes, finishes and other modifications. onsult the factory for your special requirements. Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice. 56

9 Junction oxes - Type 3R Screw over - Painted & Galvanized atalog Number Enclosure atalog Number Enclosure Size Knockout Height x Width x Dept Pattern Painted Galvanized x x D E KO No KO KO No KO in. mm in. mm in. mm Gauge ottom 444 RTS 444 RTS NK 444 RTSGV x 4.00 x x 102 x RTS 644 RTS NK x 4.00 x x 102 x RTS 664 RTS NK 664 RTSGV 664 RTSGV NK 6.00 x 6.00 x x 152 x RTS 864 RTS NK x 6.00 x x 152 x RTS 884 RTS NK 884 RTSGV 884 RTSGV NK 8.00 x 8.00 x x 203 x RTS 1084 RTS NK x 8.00 x x 203 x RTS RTS NK RTSGV RTSGV NK x x x 254 x RTS 1284 RTS NK x 8.00 x x 203 x RTS RTS NK x x x 254 x RTS RTS NK RTSGV RTSGV NK x x x 305 x RTS x x x 305 x RTS RTS NK x x x 305 x RTS RTS NK x x x 406 x RTS x x x 305 x RTS RTS NK x x x 457 x RTS RTS NK x x x 610 x RTS 666 RTS NK 666 RTSGV 666 RTSGV NK 6.00 x 6.00 x x 152 x RTS 866 RTS NK x 6.00 x x 152 x RTS 886 RTS NK 886 RTSGV 886 RTSGV NK 8.00 x 8.00 x x 203 x RTS 1086 RTS NK x 8.00 x x 203 x RTS RTS NK RTSGV RTSGV NK x x x 254 x RTS x 8.00 x x 203 x RTS RTS NK x x x 254 x RTS RTS NK RTSGV RTSGV NK x x x 305 x RTS RTS NK x x x 305 x RTS RTS NK x x x 406 x RTS RTS NK RTSGV NK x x x 305 x RTS RTS NK RTSGV RTSGV NK x x x 457 x RTS RTS NK x x x 305 x RTS RTS NK x x x 457 x RTS RTS NK RTSGV NK x x x 610 x RTS NK x x x 914 x RTS RTS NK RTSGV NK x x x 254 x RTS RTS NK RTSGV NK x x x 305 x RTS RTS NK x x x 305 x RTS RTS NK RTSGV NK x x x 457 x I J RTS RTS NK x x x 406 x I RTS RTS NK x x x 457 x I J RTS RTS NK RTSGV NK x x x 610 x I J RTS NK x x x 914 x RTS RTS NK x x x 305 x RTS x x x 305 x RTS RTS NK x x x 457 x RTS RTS NK x x x 457 x RTS RTS NK RTSGV NK x x x 610 x RTS RTS NK x x x 610 x RTS NK x x x 762 x RTS RTS NK RTSGV NK x x x 610 x RTS RTS NK x x x 610 x I I J I J I I J I J I J RTS NK x x x x 762 x RTS RTS NK x x x 610 x I J RTS NK x x x 762 x RTS NK RTSGV NK x x x 914 x D E D E D E D E D E D E D E D E D E D E D E D E D E D D D E D E F G H F G H F G H F G H F G H F G H D E D E F G H F G H F G H F G H F G H F G H F G H I J I J I J I J I J I J

10 Junction oxes Type 3R Hinge over Data Sheet and atalog Number Finish Wash and phosphate undercoat NSI 61 gray acrylic electrocoat finish pplication Used as wiring boxes, junction and pull boxes Protects against falling rain, sleet and external ice formation Standards UL 50 listed, Type 3R S 22.2 No. 40 certified, Type 3R onforms to NEM standard for Type 3R ccessories Touch-up paint See ccessories section onstruction Enclosure and door are fabricated from code gauge galvaneal steel, (see table) Enclosure body has embossed mounting holes on the back vailable with or without knockouts on the bottom end of enclosures less than 30 inches wide over is secured to the top end with galvanized, detachable formed hinges on sizes up to and including over can be held in the open position by sliding it into notches on body over has padlock hasp and sealing hole provisions at the bottom Discount Schedule: 2 Subclass: T0 Enclosure Enclosure Size Knockout atalog Number Pattern Height x Width x Depth x x D E KO No KO in. mm in. mm in. mm Gauge ottom 644 RTH 644 RTH NK 6.00 x 4.00 x x 102 x D 664 RTH 664 RTH NK 6.00 x 6.00x x 152 x D E 864 RTH 864 RTH NK 8.00 x 6.00x x 152 x D E 884 RTH 884 RTH NK 8.00 x 8.00x x 203 x RTH RTH NK 10.00x10.00x x 254 x RTH RTH NK 12.00x12.00x x 305 x RTH 1286 RTH NK 12.00x8.00x x 203 x RTH RTH NK 12.00x10.00x x 254 x RTH RTH NK 12.00x12.00x x 305 x RTH RTH NK 18.00x12.00x x 305 x RTH RTH NK 12.00x12.00x x 305 x RTH RTH NK 18.00x18.00x x 457 x I J RTH RTH NK 24.00x18.00x x 457 x I J RTH RTH NK x x x 610 x I J RTH RTH NK x x x 610 x I J RTH RTH NK x x x 610 x I J RTH NK x x x 762 x Notes: ooper -Line can provide special sizes, finishes and other modifications. onsult the factory for your special requirements. Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice. 58

11 Junction oxes Type 3R Hinge over Illustration Sheet E D (32) formed hinge -.25 (6) Front View.25 (6) mounting hole (4PL) Side View padlock hasp knockout area (see table for pattern, see detail for size) ottom View over Style on and larger 1.87 (47) 1.87 (47) D E F 3 /4-1 3 / /4 G H 3/4-1 I J 3 /4-1 K onduit Sizes Knockout Detail Note: See table for applicable knockout pattern. 59

12 Junction oxes Type 3 Screw over - Gasketed Data Sheet pplication Used as wiring boxes, junction and pull boxes Intended for indoor or outdoor use Protects against windblown dust, rain, sleet, external ice formation and dripping non-corrosive liquids Standards UL 508 listed, Type 3 and Type 12 onforms to NEM standard for Type 3 and Type 12 Finish right galvanized finish Zinc-rich coating over all external welds onstruction Enclosure and cover are fabricated from code gauge G-90 grade galvanized steel, (see table, page 61) ll continuous welded seams are finished smooth Enclosure standard without knockouts over is attached with gasketed screws over has a fixed, oil and water resistant gasket #10-32 weldnut is furnished for optional ground lug kit Discount Schedule: 2 Subclass: R0 ccessories Ground lug kit See ccessories section Notes: ooper -Line can provide special sizes, finishes and other modifications. onsult the factory for your special requirements. 60

13 Junction oxes Type 3 Screw over - Gasketed Illustration Sheet and atalog Number (32) gasketed screw (32) Front View Side View Enclosure Enclosure Size Height x Width x Depth ody over atalog Number x x in. mm Gauge Gauge 444 SG 4.00 x 4.00 x x 102 x SG 6.00 x 6.00 x x 152 x SG 8.00 x 6.00 x x 152 x SG 8.00 x 8.00 x x 203 x SG x 8.00 x x 203 x SG x x x 254 x SG x x x 305 x SG 6.00 x 6.00 x x 152 x SG 8.00 x 8.00 x x 203 x SG x x x 254 x SG x x x 254 x SG x x x 305 x SG x x x 305 x SG x x x 406 x SG x x x 457 x SG x x x 406 x SG x x x 610 x SG x x x 305 x SG x x x 508 x SG x x x 508 x SG x x x 610 x SG x x x 610 x SG x x x 762 x SG x x x 914 x

14 Junction oxes Type 3 Weatherproof Screw over Data Sheet pplication Used as wiring boxes, junction and pull boxes Protects against windblown dust, rain, sleet and external ice formation Standards UL 50 listed, Type 3 and Type 12, (unless noted) S 22.2 No. 40 certified, Type 3 and Type 12 onforms to NEM standard for Type 3 and Type 12 Finish Wash and phosphate undercoat NSI 61 gray polyester powder finish ccessories Ground lug kit Touch-up paint See ccessories section onstruction Enclosure and door are fabricated from code gauge steel, (see table, page 63) ll continuous welded seams are finished smooth Enclosure standard without knockouts over is attached with gasketed screws over has flanged sides which secure a fixed, water and ice-resistant gasket #10-32 weld stud is furnished for optional ground lug kit External mounting feet are provided for secure wall mounting Discount Schedule: 2 Subclass: R0 Notes: ooper -Line can provide special sizes, finishes and other modifications. onsult the factory for your special requirements. 62

15 Junction oxes Type 3 Weatherproof Screw over Illustration Sheet and atalog Number D E (32) (32) gasketed screw (32) Front View.31 (8) mounting hole (4PL) Side View Enclosure Enclosure Size Height x Width x Depth x x D E atalog Number in. mm in. mm in. mm Gauge 444 WPS* 4.00 x 4.00 x x 102 x WPS* 6.00 x 4.00 x x 102 x WPS 6.00 x 6.00 x x 152 x WPS 8.00 x 6.00 x x 152 x WPS 8.00 x 8.00 x x 203 x WPS x 8.00 x x 203 x WPS x x x 254 x WPS x x x 305 x WPS x x x 457 x WPS 6.00 x 6.00 x x 152 x WPS 8.00 x 8.00 x x 203 x WPS x x x 254 x WPS x 8.00 x x 203 x WPS x x x 305 x WPS x x x 305 x WPS x x x 305 x WPS x x x 457 x WPS x x x 457 x WPS x x x 610 x WPS x x x 305 x WPS x x x 457 x WPS x x x 610 x WPS x x x 610 x * UL 508 listed, Type 3 and Type 12 63

16 Panel Enclosures Type 1 Small Data Sheet pplication Houses electrical controls and instruments in an environment which does not require oil or dust tight specifications Protects against contact with enclosed equipment Standards UL 50 listed, Type 1 S 22.2 No. 40 certified, Type 1 onforms to NEM standard for Type 1 Finish Wash and phosphate undercoat NSI 61 gray polyester powder finish onstruction Enclosure and cover are fabricated from (16) gauge steel Enclosure body has mounting holes on the back which are accessible with or without the optional panel installed over is secured to the body with a continuous hinge on one side and flush latch on the opposite side Flush latch is designed to operate with either coin or screwdriver #10-32 provisions for mounting optional panel No knockouts Discount Schedule: 2 Subclass: D70 ccessories Panels Terminal blocks Type 1 flush lock Touch-up paint #8-32 self tapping screw (10168) See ccessories section Notes: ooper -Line can provide special sizes, finishes and other modifications. onsult the factory for your special requirements. 64

17 Panel Enclosures Type 1 Small Illustration Sheet and atalog Number Enclosure Enclosure Size Panel Panel Size Height x Width x Depth atalog Number atalog Number x x Height x Width in. mm Solid Perforated in. mm x 6.00 x x 152 x 102 N66P N66PP 4.25 x x x 6.00 x x 152 x 102 N86P N86PP 6.25 x x x 8.00 x x 203 x 102 N88P N88PP 6.25 x x x 8.00 x x 203 x 102 N108P N108PP 8.25 x x x x x 254 x 102 N1010P N1010PP 8.25 x x x x x 254x 102 N1210P N1210PP x x x x x 305 x 102 N1212P N1212PP x x x x x 305 x 102 N1412P N1412PP x x x 6.00 x x 152 x 152 N86P N86PP 6.25 x x x 8.00 x x 203 x 152 N88P N88PP 6.25 x x x 8.00 x x 203 x 152 N108P N108PP 8.25 x x x x x 254 x 152 N1010P N1010PP 8.25 x x x x x 254 x 152 N1210P N1210PP x x x x x 305 x 152 N1212P N1212PP x x x x x 305 x 152 N1412P N1412PP x x x x x 305 x 152 N2012P N2012PP x x x x x 305 x 203 N1212P N1212PP x x x x x 305 x 203 N1412P N1412PP x x 260 continuous hinge (60) panel mount provision (4PL) (60) (28) (28) Front View L.50 (13) cover latch (see Detail).25 (6) mounting hole (4PL) 1.50 (38) 1.81 (46) -.40 (10) Side View optional panel 65 Detail 1.37 (35) flush latch

18 Panel Enclosures Type 1 Medium Data and Illustration Sheet pplication Houses electrical controls and instruments in an environment which does not require oil and dust tight specifications Protects against contact with enclosed equipment Standards UL 50 listed, Type 1 S 22.2 No. 40 certified, Type 1 onforms to NEM standard for Type 1 Finish Wash and phosphate undercoat NSI 61 gray polyester powder finish Optional panels have a white polyester powder finish ccessories Panels Terminal blocks Type 1 flush lock Type 1 security latch inserts Touch-up paint See ccessories section #8-32 self tapping screw (10168) onstruction Enclosure and door are fabricated from code gauge steel, (see table, page 67) Enclosure body has mounting holes on the back which are accessible with or without the optional panel installed Door is secured to the body with a continuous hinge on one side and a flush latch mounted to the opposite side Flush latch is designed to operate with either coin or screwdriver provisions for mounting optional panel No knockouts Discount Schedule: 2 Subclass: D80 14 gauge panel (optional) (76) -**.44 x.81 (11 x 21) mounting hole (2PL) panel mount provision (omit center studs where is less than 30) cover latch (32) L (-*) (see Detail, page 67) (32) panel mount provision (omit center studs where is less than 30) -.56 (14) Front View 1.06 if is 24 or less 1.25 if is 30 or more body stiffener (omit where is less than 30) L Section X-X.44 (11) mounting hole (2PL) X ottom View optional panel X Note: * = 4.50 if is 24 or less * = 5.50 if is 30 or more ** = 5.00 if is 24 or less ** = 7.25 if is 30 or more. Notes: ooper -Line can provide special sizes, finishes and other modifications. onsult the factory for your special requirements. Dimensions are in inches. Millimeters shown are for reference only. Data subject to change without notice. 66

19 Panel Enclosures Type 1 Medium Illustration Sheet and atalog Number Enclosure Enclosure Size Panel Panel Size Height x Width x Depth atalog Number x x Height x Width atalog Number in. mm Gauge Solid Perforated in. mm x x x 305 x W1612-1P W1612-1PP x x x x x 406 x W1616-1P W1616-1PP x x x x x 508 x W1620-1P W1620-1PP x x x x x 406 x W2016-1P W2016-1PP x x x x x 508 x W2020-1P W2020-1PP x x x x x 406 x W2416-1P W2416-1PP x x x x x 508 x W2420-1P W2420-1PP x x x x x 610 x W2424-1P W2424-1PP x x x x x 508 x W3020-1P W3020-1PP x x x x x 610 x W3024-1P W3024-1PP x x x x x 610 x W3624-1P W3624-1PP x x x x x 762 x W3630-1P W3630-1PP x x x x x x 305 x W1612-1P W1612-1PP x x x x x 406 x W2016-1P W2016-1PP x x x x x 508 x W2020-1P W2020-1PP x x x x x 610 x W2024-1P W2024-1PP x x x x x 508 x W2420-1P W2420-1PP x x x x x 610 x W2424-1P W2424-1PP x x x x x 508 x W3020-1P W3020-1PP x x x x x 610 x W3024-1P W3024-1PP x x x x x 762 x W3030-1P W3030-1PP x x x24.00x x 610 x W3624-1P W3624-1PP x x x30.00x x 762 x W3630-1P W3630-1PP x x x24.00x x 610 x W4224-1P W4224-1PP x x x20.00x x 508 x W2420-1P W2420-1PP x x x24.00x x 610 x W3024-1P W3024-1PP x x x20.00x x 508 x W2420-1P W2420-1PP x x x24.00x x 610 x W2424-1P W2424-1PP x x x24.00x x 610 x W3024-1P W3024-1PP x x x30.00x x 762 x W3630-1P W3630-1PP x x (46) 1.37 (35) flush latch Detail 67

20 Panel Enclosures Type 1 Large Data Sheet pplication Houses electrical controls and instruments in an environment which does not require oil and dust tight specifications Protects against contact with enclosed equipment Standards UL 50 Listed, Type 1 S 22.2 No. 40 certified, Type 1 onforms to NEM Standard for Type 1 Finish Wash and phosphate undercoat NSI 61 gray polyester powder finish Optional panels have a white polyester powder finish ccessories Panels Terminal blocks Type 1 flush lock Swing panel kits Window kits Touch-up paint onstruction Enclosure and door are fabricated from (14) gauge steel Enclosure body has mounting holes on the back which are accessible with or without the optional panel installed Door is secured to the body with a heavy-duty continuous hinge on one side and slotted flush latches on the opposite side ody has stiffener for extra rigidity Slotted flush latch is designed to operate with either a coin or a screwdriver provisions for mounting optional panels No knockouts Discount Schedule: 2 Subclass: D80 Notes: ooper -Line can provide special sizes, finishes and other modifications. onsult the factory for your special requirements. 68