CI/SfB (52) March 2015. Drainage products SELECTION AND INSTALLATION GUIDE

Uniclass EPIC CI/SfB (52) March 2015 Drainage products SELECTION AND INSTALLATION GUIDE

A privately owned UK company with more than fifty years experience in the industry, Wade is established as a leading manufacturer of quality drainage products. Much of the success of the business is attributable to an on-going commitment to put technology to practical use, to generate fresh ideas, and to guarantee quality assured production. This guide presents illustrations and limited data from a comprehensive range of products. For detailed information please refer to Wade technical handbooks, our CD Rom, or our website. Certification of compliance with BS EN ISO 9001 underlines our commitment to quality and service. ISO 9001

Contents Access covers General purpose and sliding 25 Floor gullies and access covers Asphalt floors 31 Direct connection gratings 21 23 Direct connection access covers 24 25 Gully assemblies for sheet floor covering 34 35 Installation guidelines 4 5 Miscellaneous floor gullies 33 Pipework adaptors 26 Pool overflow outlets 33 Side inlets 9 Stainless steel gullies 6 8, 14 16 Sub-surface gully bodies 11 Trench drains 8 Vari-Level Bodies 10 14 clamping collars 15 Gratings 16 17 Access covers 18 Accessories 19 20 Unfinished floors 32 Grease converters 52 53 Interceptors Sediment/oil 51 Linear drainage 42 50 Materials and maintenance 54 Non-freeze water points 51 Pipework adaptors 26 Roof outlets 36 41 index 55

Floor gullies Installation guidelines 1. Where applicable, screw threaded pipework adaptor into the body outlet using a suitable sealant to ensure the joint is watertight. Finished floor level 6. Where applicable, dress the membrane over the flange and into the sump of the body, ensuring that the membrane does not restrict the outlet; bolt the membrane clamping collar to the body certain collars are reversible to increase height adjustability. Note In some cases the membrane clamping collar serves to connect the grating or cover to the body, so it must be fitted even where a membrane is not used. In installations without a below-floor membrane and/or using sheet floor covering such as vinyl, the membrane clamping collar should be sealed to the body using the supplied gasket and, where supplied, fibre washers beneath the screw heads. 2. Measure the distance between the top of the connecting pipework and finished floor level. 3. Check that this distance will enable the complete gully (with extensions, if applicable) to be installed with the top face of the grating or cover flush and level with the finished floor. Note Where a damp-proof membrane is used, the body must be installed with the top of the flange at or below membrane level. 7. Fit grating, cover, or funnel with extensions, frame or collar as applicable; set top face flush and level with the finished floor using height adjustability features. Use a suitable, good quality sealant on all threaded joints to ensure a watertight assembly. All joints need to be sealed to ensure that leaks do not occur in the event of water backing up in the gully, e.g. if a downstream pipe blockage occurs. The exception is gully assemblies specified with weepholes, which are designed to provide supplementary drainage from above the membrane; these weepholes should not generally be sealed. Level 4. Connect body (with threaded pipework adaptor if applicable) to pipework. 5. Infill as required. 8. Infill or lay floor screed and apply final floor finish (e.g. tiles, marble, paviors, terrazzo) around the grating or cover. Note Installation of gratings and covers for use with sheet floor covering, such as vinyl, is illustrated in a separate brochure. 4

Floor gullies Typical installations Finished floors Finished floor Floor screed Damp proof membrane Damp proof membrane Finished floor Floor screed Grating Filter bucket (optional) L24 series grating Contoured channel tile Damp proof membrane Optional membrane clamping collar Bell trap Optional side inlet clamping collar Body Floor screed Structural slab Pipework adaptor (select separately) Structural slab Optional side inlet Structural slab Vari-Level adaptor or body (G series shown) Stainless steel trapped gully (See pages 6 to 8 and 14) Vari-Level, non-trapped (See pages 10 to 11 and 16 to 19) Vari-Level, trapped, with contoured grating (See pages 12 to 18) Finished floor Grating/cover clamping collar Finished floor Secured flat grating clamping collar Sheet floor covering clamping collar Floor covering Grating/cover Structural slab Pipework adaptor Body Removable bottle trap Structural slab Body Pipework adaptor (select separately) Optional side inlet Body Timber support Timber packing Rodding access plug Vari-Level trapped (with removable bottle trap) with bituminous membrane (See pages 11 and 16 to 19) Uni-Level non-trapped with asphalt or composition floor (See page 31) Vari-Level trapped with sheet floor covering in a wooden floor (See pages 12 to 18) Unfinished floors Floor Floor screed Damp proof membrane Grating Floor Floor screed Damp proof membrane Grating Floor Floor screed Damp proof membrane Grating clamping collar Body clamping collar Body clamping collar Body Pipework adaptor (select separately) Structural slab Pipework adaptor (select separately) Structural slab Pipework adaptor (select separately) Structural slab Multi-Level non-trapped (See page 32) Multi-Level non-trapped (See page 32) Multi-Level non-trapped (See page 32) 5

Stainless steel gullies for finished floors 200mm square body assemblies (trapped 60mm seal), for use with gratings shown below Stainless steel grade 304 (add suffix M for grade 316 versions). See also pages 14 and 16 for Vari-Level versions 200 sq. 200 sq. 72 Max 47 Min 111.5 clamping collar (optional) 72 Max 47 Min clamping collar (optional) 186.5 256.5 110 O.D. 90.5 Q2434 height adjustable body assembly with Q9233 Streamline grating. Q2334 100 110 O.D. Q2434 100 Options 200 sq. 200 sq. Bolt-on funnel Stainless steel (U511) 285 140 Gasket seal 110 O.D. 215 Removable bell trap assembly (optional) Filter bucket (Suffix B ) Stainless steel Nylon (Q2734 or Q2834) (Q2334 or Q2434) 60 Q2734 100 110 O.D. Q2834 100 Side inlets maximum 2" BSP see page 9 for details Add suffix V for versions with sheet floor covering clamp Note FFL 225mm sq; overall height increase is 22mm 192mm square Stainless steel grating and cover with inlet (for use with body assemblies shown above) Anti-slip mesh Q4232 Load class L15 Smooth perforated Circular apertures Load class Q6230 K3 Bar grating Load class *Q7235 M125 Streamline Q9233 Load class L15 Cover with 55 diameter inlet U5232 Plain mesh Q5232 Load class L15 Square apertures Q6430 Load class K3 (*for use with Q2734 and Q2834 only) 6

Stainless steel gullies for finished floors 300mm square body assemblies (trapped 60mm seal), for use with gratings shown below Stainless steel grade 304 (add suffix M for grade 316 versions) 300 sq 300 sq 210 150 510 60 60 300 93 Integral trap Q1234V Q1234 gully body assembly with optional sheet flooring clamp (option V ) and Q4332 anti-slip mesh grating. 75 60 to suit 100mm or 150mm BS 416 Q1034 100 Q1036 150 Q1234 100 Options Filter bucket Stainless steel (Suffix B ) (Q1234, Q1334) (Q1034, Q1036, Q1434, Q1436) 210 150 60 93 60 300 sq Integral trap to suit 100mm BS 416 300 250 75 60 300 sq O ring seal Removable bell trap assembly (optional) to suit 100mm or 150mm BS 416 Bolt-on funnel Stainless steel (U511) Removable bell trap assembly (Q1434, Q1436) Non-trapped body assembly (Suffix N ) Only applies to Q1034, Q1036, Q1434 and Q1436 Side inlets maximum 100mm see page 9 for details Q1334 100 Q1434 100 Q1436 150 Add suffix V for versions with sheet floor covering clamp Note FFL 325mm sq Overall height increase 15-22mm 293mm square Stainless steel grating (for use with body assemblies shown above) Anti-slip mesh Q4332 Load class L15 Plain mesh Q5332 Load class L15 Bar grating Q7335 Load class M125 Streamline Q9333 Load class L15 7

Stainless steel gullies Heavy duty lorry deck gully Stainless steel grade 304, matt finish (add suffix M for grade 316 versions) Heavy duty gully with peripheral drainage slot, designed for use in areas subject to high loads such as lorry decks, service and parking areas. Optional lower flange may be used as a deck mounting flange and/or a membrane flange. flange with upstand 350 sq. 200 sq. 20 Solid grating with periphera slot (secured) 80 tba Lower flange (optional) 220 90 110 dia plastic and BS 416 Grating free Max. aperture Load rating Kg area cm 2 width mm class Q904 144 20 D400 17.5 Q904F lorry deck gully with optional lower flange Options Lower flange (Suffix F ) specify position. Made of grade 316 stainless steel add suffix M. Trench drain Stainless steel grade 304 For use in gutters and trenches 400 327 x 176 flange and clamp (optional) 63 153 110 dia plastic and BS 416 Note Wade manufacture a wide range of linear drainage products see pages 42 50. Grating type Grating free area cm 2 Load rating class Q605 Anti-slip mesh 360 L15 Q615 Plain mesh 360 L15 Q625 Streamline 245 L15 Q635 Perforated circular 100 K3 Q645 Perforated square 95 K3 Q605F trench drain with optional flange and clamp and anti-slip mesh grating Options Flange (Suffix F ) clamp (Suffix C ) 8

Floor gullies Side inlets For typical installation illustrations, see pages 5 and 27 Side inlets in a gully permit the underfloor connection of pipes from fixtures such as sinks and wash basins, from drainage channels and from other gullies. Side inlets in Wade trapped gullies are located completely above the water level, except in G102, H102 and GD series where the inlets are partially below the water level. The illustrations represent typical gully bodies, viewed from above, and show the s for all possible combinations of locations. Unless otherwise requested, side inlets in cast iron gully bodies will be supplied as BSP female threads (specify thread ); stainless steel bodies have BSP female threads up to 2"; above 2", spigot inlets are supplied to suit BS 416 pipework. GP1104 plastic gully body has three side inlets moulded-in that will connect to 50mm plastic pipework; these inlets are usable by removing knock-outs from the body on site. Denotes side inlet locations. Denotes outlet position (where applicable). Gully bodies with vertical outlet 1A 2A 2B 3A 4A Gully bodies with P or S trapped outlet 1A 1B 1C 2A 2B 2C 3A Gully bodies with horizontal outlet 1A 1B 1C 2A 2B 2C 3A To specify/order Quote the for the selected body with suffix ][ and the locations and of each inlet. e.g. G304 body with 2 side inlets tapped 1.5" BSP, in locations per illustration 2B. Specify: G304][ 2B 1.5 9

Vari-Level non-trapped bodies Cast iron For use with Vari-Level threaded gratings/covers shown on pages 16 18, 31 and 33 Connections Bodies with threaded outlet are for connection to pipework by means of a threaded pipework adaptor shown on page 26. Medium sump clamping collar (required) 200 dia. clamping collar (required) 265 dia. 115(C3) 75(C2) Gasket 115 Gasket C344 body illustrated with C.C membrane clamping collar and gasket Deep sump Pipework Body Collar system C202 C.C 2"BSP C203 C.C 3"BSP C204 C.C 4"BSP C343 C.C 82 Plastic C344 C.C 110 Plastic C363 C.C 75 BS437 C364 C.C 100 BS437 C393 C.C 75 BS416 C394 C.C 100 BS416 clamping collar (required) 200 dia. Body Collar D204 C.D 4"BSP D206 C.D 6"BSP clamping collar (required) 265 dia. Gasket 135 Gasket 240 C504 body illustrated with C.C membrane clamping collar, gasket and optional side inlet (see page 9 for details) Optional side inlets max.2" BSP Body Collar C502 C.C 2"BSP C503 C.C 3"BSP C504 C.C 4"BSP Optional side inlets max.4" BSP Body Collar D404 C.D 4"BSP D406 C.D 6"BSP Angled/side outlet Optional membrane clamping collar (specify C.B) 188 dia. clamping collar (required) 265 dia. clamping collar (required) 265 dia. 162 Gasket 200 Gasket B D604 body illustrated with C.D membrane clamping collar and gasket 45 B504 4"BSP Note See page 15 for alternative membrane clamping collars. ( clamping collar is optional for B504.) 45 Body Collar D604 C.D 4"BSP Horizontal outlet Pipework Body Collar system B D702 C.D 2"BSP 86 D703 C.D 3"BSP 73 D704 C.D 4"BSP 83 10

Vari-Level non-trapped bodies Cast iron For use with Vari-Level threaded gratings/covers shown on pages 16 18, 31 and 33 Connections Bodies with spigot outlet are for direct connection to pipework, versions with threaded outlet are for connection to pipework by means of a threaded pipework adaptor shown on page 26. For use with bituminous membrane Typical gully assembly D1109 body with C.D10 membrane clamping collar, gasket and K2103 nickel bronze grating clamping collar (required) 305 dia. clamping collar (required) 305 dia. clamping collar (required) 305 dia. A Gasket Gasket B 90 Gasket Threaded outlet Body Collar D1002 C.D10 2"BSP D1003 C.D10 3"BSP D1004 C.D10 4"BSP Spigot outlet Body Collar A D1107 C.D10 50mm BS 416 238 D1108 C.D10 75mm BS 416 165 D1109 C.D10 100mm BS 416 190 Horizontal outlet Body Collar B D1207 C.D10 2"BSP 80 D1208 C.D10 3"BSP 67 D1209 C.D10 4"BSP 117 For sub-surface drainage such as with cavity membranes 305 dia. 220 dia. Cast iron slotted membrane clamp (included) 305 dia. 220 dia. Cast iron slotted membrane clamp (included) 305 dia. 220 dia. Cast iron slotted membrane clamp (included) 90 A B Threaded outlet SD102 SD103 SD104 2"BSP 3"BSP 4"BSP Spigot outlet A SD202 50mm BS 416 238 SD203 75mm BS 416 165 SD204 100mm BS 416 190 Horizontal outlet B SD302 2"BSP 80 SD303 3"BSP 67 SD304 4"BSP 117 Note See page 15 for alternative membrane clamping collars. 11

Vari-Level trapped bodies Cast iron For use with Vari-Level threaded gratings/covers shown on pages 16 18, 31 and 33 Connections Bodies with spigot outlet are for direct connection to pipework, versions with threaded outlet are for connection to pipework by means of a threaded pipework adaptor shown on page 26. P Trapped 50mm seal Optional membrane clamping collar (Add suffix C ) Optional membrane clamping collar (Add suffix C ) A B A B G303C Body illustrated with optional membrane clamping collar and optional side inlets G804C Body with optional membrane clamping collar S Trapped 50mm seal E Optional side inlets max. 2" BSP A E B G102* 2"BSP 142 140 60 Optional membrane clamping collar (Add suffix C ) E Optional side inlets max. 2" BSP A E B G202 2"BSP 170 185 85 G203 3"BSP 205 190 96 G303 75mm 170 185 80 G304 100mm 205 190 92 G804 100mm 205 131 102 A B G604C Body with optional membrane clamping collar G1004C Body with optional membrane clamping collar E Optional side inlets max. 2" BSP A E B G502 2"BSP 170 145 150 G503 3"BSP 205 156 165 G603 75mm 170 145 150 G604 100mm 205 155 165 G1004 100mm 205 37 205 P Trapped 100mm seal B Optional membrane clamping collar (Specify C.H1 or C.H2) H204 Body with optional C.H2 membrane clamping collar * Denotes 3" throat A E Optional side inlets (H1 = max. 1½" BSP) (H2 = max. 2" BSP) Body Collar A E B H102* C.H1 2"BSP 250 161 54 H203 C.H2 3"BSP 345 225 76 H204 C.H2 4"BSP 345 225 76 Options All cast iron trapped bodies have facility for optional side inlets, see page 9 for details. clamping collar is optional on G and H series bodies. Linear Drainage (G2-G10 series only, suffix LD ) to connect to Wade drainage channel with 110 114mm O.D spigot. A channel sealing kit is supplied with the purpose machined body. 12

Vari-Level trapped bodies Cast iron For use with Vari-Level threaded gratings/covers shown on pages 16 18, 31 and 33 (See note at foot of page). Connections Bodies with spigot outlet are for direct connection to pipework, versions with threaded outlet are for connection to pipework by means of a threaded pipework adaptor shown on page 26. P Trapped with rodding access 100mm seal J204 with optional C.J2 membrane clamping collar Close proximity of grating and access cover prevents the adjacent use of widest versions. A B D Optional side inlets max. 2" BSP A B C D J204 4"BSP 345 405x225 76 178 C Optional membrane clamping collar (Specify C.J2) To specify/order For GC and GD series, specify Body and Collar from table; see page 15 for alternative membrane clamping collars. Note membrane clamping collar is optional for J204 and is included with GP series. Options All cast iron trapped bodies have facility for optional side inlets, see page 9 for details. Bell Trapped 50mm seal with full bore rodding access GD144 Body with C.D membrane clamping collar, gasket and optional side inlet. (Note: Side inlets up to 2" are completely above water level, over 2" are partially below). 304 265 dia. 180 clamping collar (required) Gasket Optional side inlets max. 4" BSP Pipework Body Collar system GD144 C.D 100 BS 416/DIN 19522/ { Plastic 110mm GD164 C.D 100 BS 437 Bottle trapped Vertical outlet 50mm seal for use in low volume drainage applications Optional side inlets max. 2" BSP Body Collar GC144 C.C 100 { Pipework system BS 416/DIN 19522/ Plastic 110mm Vari-Level trapped body assemblies ABS plastic clamping collar (included) 220 dia. 187 dia. clamping collar (included) 104 50 220 dia. Gasket 105 (Invert) 56 dia. Gasket 103 50 157 clamping collar (included) Gasket 50 71 202 50mm seal Pipework system GP312 50 Plastic 50mm seal Pipework system GP614 110/50 Plastic Frequent cleaning will be necessary in applications where very high amounts of hair and other waste materials are present (GP312/GP614). 134 50mm seal. Optional untrapped side inlets 56mm o.d, spigot. Pipework system GP1104 110 Plastic/BS 416 Note Bodies on this page are for use with Vari-Level gratings/covers with 4" throat; except K2801, K2901, K3201 or K3202 which cannot be used with GC, GD or GP series bodies. J204 may also be used with versions with 3" throat. (If used with U1101 reducing bush see page 19). 13

Vari-Level bodies Stainless steel grade 304 For use with Vari-Level threaded gratings/covers shown on pages 16 18 and accessories shown on page 19 Connections Bodies have spigot outlet for direct connection to pipework. Non-trapped QB114 Vertical outlet QB214 Horizontal outlet 192 dia. 4" NPSM Optional membrane clamping collar 192 dia. 4" NPSM Optional membrane clamping collar 82 140 138 60 110 O.D. 185 dia. Optional side inlets up to four at 90 2" BSP Max to suit BS 416/DIN 19522/plastic (100mm nominal bore) 110 O.D. to suit BS 416/DIN 19522/plastic (100mm nominal bore) 185 dia. Optional side inlets up to three at 90 2" BSP Max QB114C body with optional membrane clamping collar mm Free area cm 2 QB114 100 78 2.3 QB214 100 78 2.1 kg Trapped QG114 Vertical outlet bell trapped QG214 Horizontal outlet P trapped 192 dia. 4" NPSM Optional membrane clamping collar Rodding access plug and seal 111 192 dia. 4" NPSM Optional membrane clamping collar Rodding access plug and seal 186 90 60 110 O.D. 185 dia. Optional side inlets up to four at 90 2" BSP Max Fixed bell assembly (included) Removable upstand Gasket seal to suit BS 416/DIN 19522/plastic (100mm nominal bore) 256 110 O.D. to suit BS 416/DIN 19522/plastic (100mm nominal bore) 185 dia. 60 Fixed trap (included) Optional side inlets up to three at 90 2" BSP Max QG114C Bell trapped body with rodding access 60mm seal, with optional membrane clamping collar mm Free area cm 2 Trap type QG114 100 51 Bell 2.8 QG214 100 60 P 3.5 kg Options clamping collar is optional on QB and QG series bodies, add suffix C to specify. All stainless steel bodies have facility for optional side inlets see page 9 for details. Add suffix M to for grade 316 stainless steel. Linear Drainage (Suffix LD ) to connect to Wade drainage channel with 110 114mm O.D spigot. A channel sealing kit is supplied. Weepholes (Suffix W ) to provide supplementary drainage at membrane level. 14

Vari-Level membrane clamping collars Application chart Body / series For use with 4" throat Vari-Level grating/cover clamping collar s For use with 3" throat Vari-Level grating/cover B504 C.B (optional) C.B (optional) and U1101* C series D2-D7 series D10-D12 series C.C standard 4" throat version (gasketed) C.CW includes weepholes (not sealed) C.CL accepts Wade 114 dia. channel outlet (not sealed) C.D standard 4" throat version (gasketed) C.DL accepts Wade 114 dia. channel outlet (not sealed) C.DW includes weepholes (not sealed) C.DLW includes weepholes (not sealed) C.D10 standard 4" throat version (gasketed) C.D10L accepts Wade 114 dia. channel outlet (not sealed) C.D10W includes weepholes (not sealed) C.D10LW accepts Wade 114 dia. channel outlet includes weepholes (not sealed) C.C3 standard 3" throat version (gasketed) C.CW3 includes weepholes, 3" throat (not sealed) C.D and U1101* standard version (gasketed) C.DW and U1101* includes weepholes (not sealed) C.D10 and U1101* standard version (gasketed) C.D10W and U1101* includes weepholes (not sealed) G1 series add suffix C to body (optional), and U201 Add suffix C to body (optional) G2-G10 series add suffix C to body (optional) Not applicable (3" throat gratings/covers are not recommended for use with this body series) GC144 GD series GP series C.C standard 4" throat version (gasketed) C.CW includes weepholes (not sealed) C.D standard 4" throat version (gasketed) C.DW includes weepholes (not sealed) This series is supplied as an assembly which includes a body, membrane clamping collar and gasket H102 C.H1 (optional) and U201 C.H1 (optional) Not applicable (3" throat gratings/covers cannot be used with this body series) Not applicable (3" throat gratings/covers cannot be used with this body series) Not applicable (3" throat gratings/covers cannot be used with this body series) H2 series C.H2 (optional) C.H2 (optional) and U1101* J204 C.J2 (optional) C.J2 (optional) and U1101* QB series Add suffix C to body (optional) Add suffix C to body and U1101* QG series Add suffix C to body (optional) Not applicable (3" throat gratings/covers are not recommended for use with this body series) * U1101 reducing bush enables 3" throat gratings/covers to be used in Vari-Level bodies/adaptors with 4" inlet (see page 19). U201 4" NPSM to 3" NPSM extension is required if a 4" throat Vari-Level grating/cover is used with a G1 or H1 series body (see page 19). W Weepholes these are holes in membrane clamping collar that enable supplementary drainage at membrane level. L Linear for use with Wade linear drainage channel. Note Versions with weepholes (W) or for use with Wade channel (L) are not supplied with a gasket. 15

Vari-Level gratings For use with bodies shown shown on pages 10 14 and accessories shown on pages 19 20 Cast iron BS EN 1561 Sherardized, matt finish (add suffix H for versions with security fixings) Circular grating Dia. K2103 CI 155 Decorative floral pattern Size L2501 CI 150 sq. Suitable for service and parking areas, plant rooms etc. Dia. K2501 176 Suitable for service and parking areas, plant rooms etc. Size L2601 150 sq. Stainless steel grade 304 Satin finish (add suffix H for versions with security fixings) With peripheral slot for use with sheet floor covering such as vinyl Dia. K1807 176 Circular grating Dia. K2107 150 For use with sheet floor covering such as vinyl Dia. K2307 176 For use with trowel applied composition flooring. 6mm flange depth Dia. K2407 150 Flanged with peripheral slot. Self securing Dia. K2801 140 Security area drainage Dia. K2901 114 Security area drainage with Pin Torx screws Dia. K3504 150 Security area drainage for use with sheet floor covering Dia. K3604 176 Square grating Size *L2105 101 sq. L2106 147 sq. Streamline heel-proof reverse wedge profile Size L2901 150 sq. L2902 200 sq. Square perforated grating with circular apertures Size L3101 150 sq. L3102 200 sq. Square perforated grating with square apertures Size L3201 150 sq. L3202 200 sq. Anti-slip mesh (grating not secured) Size L3301 150 L3302 200 Plain mesh (grating not secured) Size L3401 150 L3402 200 Anti-slip mesh (grating not secured) for use with sheet floor covering Size L3601 175 L3602 225 Streamline heel-proof reverse wedge profile for use with sheet floor covering Size L3701 175 L3702 225 Hinged cover with circular non-secured grating inside Size L5305 135 sq. L5308 150 sq. 176 dia. Condensate funnel with vermin guard, for use with sheet floor covering Size above FFL Dia. H K3407 101 100 150 sq. Condensate funnel with vermin guard Size above FFL Dia. H L2701 101 100 16 *Denotes 3" throat (all others 4")

Vari-Level gratings For use with bodies shown shown on pages 10 14 and accessories shown on pages 19 20 Nickel bronze BS EN 1982 Satin finish (add suffix H for versions with security fixings) Circular grating Dia. K2101 135 *K2102 135 K2103 152 Indirect waste connector (grating not secured) Dia. K2201 176 For use with sheet floor covering such as vinyl Dia. *K2301 142 K2302 176 K2303 230 For use with trowel applied composition flooring. 4mm flange depth Dia. K2401 152 Reduces risk of blockages in channels. Removable dome protudes 30mm Dia. K3101 135 Standard square grating Size *L2101 101 sq. L2102 135 sq. L2103 150 sq. L2104 201 sq. Rectangular Size *L2201 102 x 204 L2202 125 x 430 Square framed grating Size L2301 150 sq. Johnson 4200 Size *L2402 115 sq. Pilkington/Wooliscroft 2302/Gail 4420 Size *L2404 150 sq. Platt 2300 L2406 Size 150 sq. Ruabon Size *L2407 150 sq. Keramic L2408 Size 150 sq. Strata Buchtal 54420 Size *L2409 150 sq. Decorative floral pattern Size L2501 150 sq. Hinged grating L3001 Size 161 sq. Grating concealed by solid hinged cover. L5401 version has sealed cover Size L5301 150 sq. L5401 150 sq. 176 dia. To take multiple indirect waste pipes; with peripheral grating (funnel not secured) Size above FFL L W H K2601 222 82 96 176 dia. To take single indirect waste pipes; with peripheral grating (funnel not secured) Size above FFL Dia. H K2701 108 96 150 dia. To take single indirect waste pipes; with peripheral cover and vermin guard Size above FFL Dia. H K3301 101 101 150 dia. To take multiple indirect waste pipes; with peripheral cover and vermin guard Size above FFL L W H K3302 222 82 96 176 dia. For use with sheet floor covering such as vinyl. With peripheral cover and vermin guard Size above FFL Dia. H K3401 101 101 Size above FFL L W H K3402 222 82 96 *Denotes 3" throat (all others 4") 150 sq. To take single indirect waste pipes; with peripheral cover and vermin guard Size above FFL Dia. H L2801 101 101 150 sq. To take multiple indirect waste pipes; with peripheral cover and vermin guard Size above FFL L W H L2803 222 82 96 17

Vari-Level access covers For use with bodies shown shown on pages 10 14 and accessories shown on pages 19 20 Ductile iron BS EN 1563 and BS EN 1564 Sherardized, matt finish (add suffix H for versions with security fixings) SuperSeal (double sealed) Dia. K5801 176 SuperSeal (double sealed) Size L5701 150 sq. Nickel bronze BS EN 1982 Satin finish (add suffix H for versions with security fixings) Gasketed, for use with sheet floor covering, such as vinyl Dia. *K5101 142 K5102 176 K5103 250 Gasketed Dia. *K5201 135 K5202 135 K5203 150 Gasketed, for use with trowel applied composition flooring. 4mm flange depth Dia. K5301 152 Plug with O ring seal for use in plunge & foot baths Dia. K5401 155 SuperSeal (double sealed) Dia. K5501 152 SuperSeal (double sealed). For use with sheet floor covering, such as vinyl Dia. K5601 176 SuperSeal (double sealed). Recessed for flooring material Dia. K5701 152 Gasketed L5101 Size 135 sq. Gasketed L5103 Size 160 sq. Hinged cover in square frame (unsealed) Size L5201 150 sq. Hinged cover with grating inside. L5401 version has sealed cover L5301 L5401 Size 150 sq. 150 sq. SuperSeal (double sealed) L5501 Size 150 sq. SuperSeal (double sealed) L5601 Size 150 sq. Stainless steel grade 304 Satin finish (add suffix H for versions with security fixings) For use with sheet floor covering, such as vinyl (unsealed) Dia. K5107 176 Gasketed Dia. K5207 150 Gasketed - for use with trowel applied composition flooring. 6mm flange depth Dia. K5307 150 SuperSeal (double sealed) Dia. K5507 150 SuperSeal (double sealed) for use with sheet floor covering Dia. K5607 176 *Denotes 3" throat (all others 4") Hinged cover with a circular non-secured grating inside Size L5305 135 sq. L5308 150 sq. SuperSeal (double sealed) L5507 Size 147 sq. SuperSeal (double sealed) Recessed for flooring material Size L5807 150 sq. 18 Note: Some versions may be tapped for waste pipe.

Accessories For use with Vari-Level and direct connection gratings and access covers Bolt-on funnels Portable funnel 200 200 U501 U502 U511 Size Dia. H U501 Nickel bronze 101 101 U502 Cast iron 101 101 U511 Stainless steel 101 101 Size L W H U601 Nickel bronze 222 82 96 U602 Cast iron 225 85 96 38 38 Stainless steel Size L W H U1202 200 200 250 U1203* 200 200 250 Backwater valve Filter bucket Nylon 6 Used to intercept debris, valuables etc. *Version without tail piece Removable bottle trap (50mm seal) Throat dia. U703 3" U704 4" If fitting U704 into a Vari-Level grating/ cover, a minimum of a U103 or UP104 extension will be required to prevent the backwater valve fouling on the Vari-Level body, unless body is C or D series with minimum 3" outlet. Note A backwater valve restricts flow; cannot be fitted if a removable bottle trap or a filter bucket is used. UP701 To fit inside gratings with 4" throat. (Not K1807, K2801, K2901 and K3211). Typical installation is shown on page 5. UP702 Deep version for use with Vari-Level gratings with bodies C5 and D4, adaptors T702, T901 and extensions U1 series. Note A filter bucket cannot be fitted if a backwater valve or removable bottle trap is used. U1404 To fit inside grating, funnel or access cover with 4" throat/outlet. Typical installation is shown on page 5. Max. flow rate 1.0 l/sec. Note 1. Cannot be used with K1807, K2801 or K2901. 2. Frequent cleaning will be necessary in applications with very high amounts of hair and other waste material. 3. A Vari-Level extension is required with 2" and 3" outlet versions of C2/C3/ D10/D11 series bodies. Grating extension Thread Female Male Height Height Min Max U101 3" 3" 127 42 120 U102 4" 4" 60 37 55 U103 4" 4" 100 40 95 U104 4" 4" 152 85 145 U201 4" 3" 115 40 110 U208 4" 25 25 25 UP104* 4" 4" 152 36 145 *All cast iron except UP104 plastic (ABS) version for use with GP series bodies. Short extension; see T1401 for illustration. Gully adaptors To connect Vari-Level gratings/covers to clay or PVC bodies 150mm sq. T1302 For use with 3" throat grating/cover T1301 For use with 4" throat grating/cover 180mm dia. Weephole T1402 For use with 3" throat grating/cover T1401 For use with 4" throat grating/cover Reducing bush U1101 To enable 3" throat gratings/covers to be used in Vari-Level bodies/adaptors with 4" inlet. Note Height of grating/cover will be increased by 15mm min./27mm max. Inlet/outlet plug UX9901 Tapered to plug, temporarily, 100mm inlet or outlet during installation. 19

Accessories For use with Vari-Level gratings, access covers and bodies Adaptors to pipework Vari-Level gratings and access covers, when used without a body, may be connected to pipework by means of an adaptor, as shown in the following tables: Adaptors for use with Vari-Level gratings and access covers with 3" throat Pipework system Overall length T701 Plastic 82mm O.D. 127 T714 Plastic 75mm O.D. 130 T712 Plastic 110mm O.D. 115 T801 C.I. BS 416 75mm 127 T712 C.I. BS 416 100mm 115 T701 C.I. DIN 19522 SMU 75mm 127 T712 C.I. DIN 19522 100mm 115 T911 Clay supersleve 100mm 145 All made of cast iron. Adaptors for use with Vari-Level gratings and access covers with 4" throat Pipework system Overall length T703 Plastic 82mm O.D. 115 T704 Plastic 75mm O.D. 115 TP702 Plastic 110mm O.D. 152 T792 C.I. BS 416 50mm 180 T803 C.I. BS 416 75mm 115 T702 C.I. BS 416 100mm 100 TP702 C.I. BS 416 100mm 152 T792 C.I. DIN 19522 50mm 180 T703 C.I. DIN 19522 SMU 75mm 115 TP702 C.I. DIN 19522 100mm 152 T901 Clay supersleve 100mm 130 T742 2" BSP male thread 220 All made of cast iron, except TP702, plastic (ABS) Installation adaptors For use with G2-G10 series trapped bodies 245mm dia. 300mm dia. U15 Stainless steel support plate and cast iron membrane clamp to adapt G2-G10 series bodies for installation in a timber deck with tile floor finish. To specify/order Add suffix D to the body U16 Stainless steel asphalt flange for use with G2-G10 series bodies. To specify/order Add suffix A to the body Deep seal P trap Cast iron 'C' 90 Swept bend Malleable iron Male hollow plug 'A' 'B' Inlet/ thread A B C U902 2" BSP 234 50 162 U903 3" BSP 318 70 210 U904 4" BSP 379 90 250 Malleable iron 90 swept bend 2" BSP male to 2" BSP female connection U1301 Thread 2" BSP M/F Malleable iron 2" BSP male hollow plug. Used to block a side inlet, must be sealed U1802 Thread 2" BSP 20

Direct connection gratings For accessories see page 19. Pipework adaptors are shown on page 26 Cast iron BS EN 1561 Sherardized, matt finish (add suffix H for versions with security fixings) Standard circular grating Dia. Pipework K2193CI 155 4" C.I. + P* Suitable for service and parking areas, plant rooms etc. Dia. Pipework K2591 176 4" C.I. + P* Decorative floral pattern Size Pipework L2591CI 150 sq. 4" C.I. + P* Suitable for service and parking areas, plant rooms etc. Size Pipework L2691 150 sq. 4" C.I. + P* Nickel bronze BS EN 1982 Satin finish (see also pages 22) (add suffix H for versions with security fixings) With central securing screw Dia. Pipework K1941 98 2" BSP Self securing Dia. Pipework K2041 98 2" BSP Standard circular grating Dia. Pipework K2142 135 82mm Plastic K2191 135 4"C.I. + P* K2193 155 4"C.I. + P* Indirect waste connector (grating not secured) Dia. Pipework K2291 176 4" C.I. + P* For use with trowel applied composition flooring. 4mm flange depth Dia. Pipework K2491 150 4" C.I. + P* Reduces risk of blockages in channels. Removable dome protrudes 30mm Dia. Pipework K3191 135 4" C.I. + P* 176 dia. To take multiple indirect waste pipes; with peripheral grating (funnel not secured) Spec Funnel Pipework K2691 224L x 85W x 99H 4" C.I. + P* 176 dia. To take single indirect waste pipes; with peripheral grating (funnel not secured) Spec Funnel Pipework K2791 108 dia. x 96H 4" C.I. + P* 150 dia. To take single indirect waste pipe; with peripheral cover and vermin guard Spec Funnel Pipework K3391 101 dia. x 101H 4" C.I. + P* 176 dia. For use with sheet floor covering such as vinyl. With peripheral cover and vermin guard Spec Funnel Pipework K3491 101 dia. x 101H 4" C.I. + P* 176 dia. For use with sheet floor covering such as vinyl. With peripheral cover and vermin guard Spec Funnel Pipework K3492 224 dia x85wx99h 4" C.I. + P* 150 sq. To take single indirect waste pipe; with peripheral cover and vermin guard Spec Funnel Pipework L2891 101 dia. x 101H 4" C.I. + P* 150 sq. To take multiple indirect waste pipes; with peripheral cover and vermin guard Spec Funnel Pipework L2893 225L x 85W x 96H 4" C.I. + P* *C.I. + P means cast iron BS 416/DIN 19522 and plastic 21

Direct connection gratings For accessories see page 19. Pipework adaptors are shown on page 26 Nickel bronze BS EN 1982 Satin finish (add suffix H for versions with security fixings) With central securing screw Size Pipework L1941 100 sq. 2" BSP Self securing Standard square grating Rectangular Size Pipework L2041 100 sq. 2" BSP Size Pipework L2141 101 sq. 82mm Plastic L2191 101 sq. 3" BS416 L2192 135 sq. 4" C.I. + P* L2193 150 sq. 4" C.I. + P* L2194 201 sq. 4" C.I. + P* Size Pipework L2241 102x204 82mm Plastic L2291 102x204 3" BS416 L2292 125x430 4" C.I. + P* Square framed grating Decorative floral pattern Hinged grating Size Pipework L2391 150 sq. 4" C.I. + P* Size Pipework L2591 150 sq. 4" C.I. + P* Size Pipework L3091 161 sq. 4" C.I. + P* Grating concealed by solid hinged cover. L5491 version has sealed cover Johnson 4200 Pilkington/Wooliscroft 2302 Gail 4420 Platt 2300 Size Pipework L5391 150 sq. 4" C.I. + P* L5491 150 sq. 4" C.I. + P* Size Pipework L2442 115 sq. 82mm Plastic L2492 115 sq. 3" BS 416 Size Pipework L2444 150 sq. 82mm Plastic L2494 150 sq. 3" BS 416 Size Pipework L2496 150 sq. 4" C.I. + P* Ruabon Keramic Strata Buchtal 54420 Size Pipework L2447 150 sq. 82mm Plastic L2497 150 sq. 3" BS 416 Size Pipework L2498 150 sq. 4" C.I. + P* Size Pipework L2449 150 sq. 82mm Plastic L2499 150 sq. 3" BS 416 For use with sheet floor covering Dia. Pipework N111 105 40mm Plastic N112** 105 40mm Plastic Dia. Pipework N211 142 40mm Plastic N213** 142 40mm Plastic N215 142 50mm Plastic N217** 142 50mm Plastic Dia. Pipework N301 142 3" BS416 N303 142 82mm Plastic N305 142 75mm Plastic Dia. Pipework N405 146 4" BS437 N410 146 4" Supersleve Dia. Pipework K2392 176 4" C.I. + P* *C.I. + P means cast iron BS 416 / DIN 19522 and plastic. ** Versions with cast iron backnut for use in timber floors. 22

Direct connection gratings For accessories see page 19. Pipework adaptors are shown on page 26 Stainless steel grade 304 Satin finish (add suffix H for versions with security fixings) With peripheral slot for use with sheet floor covering such as vinyl With central securing screw Circular grating For use with sheet floor covering, such as vinyl Dia. Pipework K1897 176 4" C.I. + P* Dia. Pipework K1947 100 2" BSP female Dia. Pipework K2197 150 4" C.I. + P* Dia. Pipework K2397 176 4" C.I. + P* For use with trowel applied composition flooring. 6mm flange depth Flanged with peripheral slot. Self securing Security area drainage Security area drainage with Pin Torx screws Dia. Pipework K2497 150 4" C.I. + P* Dia. Pipework K2891 140 4" C.I. + P* Dia. Pipework K2941 114 110 Plastic K2991 114 4" BS 416 Dia. Pipework K3594 150 4" C.I. + P Security area drainage for use with sheet floor covering With central securing screw Square grating Streamline heel proof reverse wedge profile Dia. Pipework K3694 176 4" C.I. + P Size Pipework L1947 100 sq. 2" BSP female Size Pipework L2196 147 sq. 4" C.I. + P* Size Pipework L2991 150 sq. 4" C.I. + P* L2992 200 sq. 4" C.I. + P* Square perforated grating (circular apertures) Square perforated grating (square apertures) Anti-slip mesh (grating not secured) Plain mesh (grating not secured) Size Pipework L3191 150 sq. 4" C.I. + P* L3192 200 sq. 4" C.I. + P* Size Pipework L3291 150 sq. 4" C.I. + P L3292 200 sq. 4" C.I. + P Size Pipework L3391 150 sq. 4" C.I. + P L3392 200 sq. 4" C.I. + P Size Pipework L3491 150 sq. 4" C.I. + P L3492 200 sq. 4" C.I. + P Anti-slip mesh grating for use with sheet floor covering (grating not secured) Size Pipework L3691 175 sq. 4" C.I. + P L3692 225 sq. 4" C.I. + P Streamline heel-proof reverse wedge profile for use with sheet floor covering Size Pipework L3791 175 sq. 4" C.I. + P L3792 225 sq. 4" C.I. + P Hinged cover with a circular nonsecured grating inside Size Pipework L5395 135 sq. 4" C.I. + P* L5398 150 sq. 4" C.I. + P* 176 dia. Condensate funnel with vermin guard, for use with sheet floor covering Dia. H K3497 101 101 Condensate funnel with vermin guard Size dia. Pipework L2791 114x100H 4" C.I. + P* *C.I. + P means cast iron BS 416 / DIN 19522 and plastic. 23

Direct connection access covers For accessories see page 19. Pipework adaptors are shown on page 26 Ductile iron BS EN 1563 and BS EN 1564 Sherardized, matt finish (with cast iron frame) (add suffix H for versions with security fixings) SuperSeal (double sealed) Dia. Pipework K5891 176 4" C.I. + P* SuperSeal (double sealed) Size Pipework L5791 150 sq. 4" C.I. + P* Nickel bronze BS EN 1982 Satin finish (add suffix H for versions with security fixings) Gasketed Gasketed for use with trowel applied composition flooring. Stainless steel flange 220mm dia. 4mm flange depth Plug with O ring seal for use in plunge and foot baths Dia. Pipework K5241 135 82mm Plastic K5292 135 4" C.I. + P* K5293 150 4" C.I. + P* Dia. Pipework K5391 152 4" C.I. + P* Dia. Pipework K5491 155 4" C.I. + P* SuperSeal (double sealed) SuperSeal (double sealed). Recessed for flooring material Gasketed Gasketed Dia. Pipework K5591 152 4" C.I. + P* Dia. Pipework K5791 152 4" C.I. + P* Size Pipework L5191 135 sq. 4" C.I. + P* Size Pipework L5193 160 sq. 4" C.I. + P* Hinged cover (unsealed) in square frame Size Pipework L5291 150 sq. 4" C.I. + P* Hinged cover with grating inside. L5391 version is unsealed, L5491 version has sealed cover Size Pipework L5391 150 sq. 4" C.I. + P* L5491 150 sq. 4" C.I. + P* SuperSeal (double sealed) Size Pipework L5591 150 sq. 4" C.I. + P* SuperSeal (double sealed) Size Pipework L5691 150 sq. 4" C.I. + P* For use with sheet floor covering Gasketed Gasketed Gasketed Gasketed Dia. Pipework Dia. Pipework Dia. Pipework N212 142 40mm Plastic N302 142 3" BS 416 N404 146 4" BS 437 N214 142 40mm Plastic N304 142 82mm Plastic N409 146 4" SuperSleve N216 142 50mm Plastic N306 142 75mm Plastic N218 142 50mm Plastic Dia. Pipework K5192 176 4" C.I. + P* SuperSeal (double sealed) Dia. Pipework K5691 176 4" C.I. + P* *C.I. + P means cast iron BS 416 / DIN 19522 and plastic. Note: Some versions may be tapped for waste pipe. (N214 and N218 have backnut included) 24

Direct connection access covers For accessories see page 19. Pipework adaptors are shown on page 26 Stainless steel grade 304 Satin finish (add suffix H for versions with security fixings) For use with sheet floor covering, such as vinyl (unsealed) Dia. Pipework K5197 176 4" C.I. + P* Gasketed Dia. Pipework K5297 150 4" C.I. + P* Gasketed for use with trowel applied composition flooring. 6mm flange depth Dia. Pipework K5397 150 4" C.I. + P* SuperSeal (double sealed) Dia. Pipework K5597 150 4" C.I. + P* SuperSeal (double sealed) For use with sheet floor covering, such as vinyl Dia. Pipework K5697 176 4" C.I. + P* Hinged cover with a circular non-secured grating inside Size Pipework L5395 135 sq. 4" C.I. + P* L5398 150 sq. 4" C.I. + P* SuperSeal (double sealed) Size Pipework L5597 147 sq. 4" C.I. + P* *C.I. + P means cast iron BS 416 / DIN 19522 and plastic. Note: Some versions may be tapped for waste pipe. SuperSeal (double sealed) Recessed for flooring material Size Pipework L5897 150 sq. 4" C.I. + P* Access covers General purpose and sliding Nickel bronze BS EN 1982 Satin finish Unsealed, secured Dia. R311 186 Unsealed, secured Size R411 178 sq. R412 229 sq. Stainless steel cover. For use in wall Size R511 178 sq. R512 229 sq. Sealed, recessed for flooring material Dia. R611 138 Sealed Dia. R621 138 Sealed, secured, recessed for flooring material Size R801 205 sq. Sliding access covers for flexible sheet floor covering (add suffix H for versions with security fixings) Double sealed sliding access cover Stainless steel grade 304 W L Clear opening Overall Opening direction RS231 450 x 450 684 x 684 RS232L 450 x 600 684 x 834 Length RS232W 600 x 450 834 x 684 Width RS233 600 x 600 834 x 834 RS234L 600 x 750 834 x 984 Length RS234W 750 x 600 984 x 834 Width RS235 750 x 750 984 x 984 RS236L 600 x 900 834 x 1134 Length RS236W 900 x 600 1134 x 834 Width Man entry ( Patent pending) Easy open sliding mechanism can be opened and closed safely by one person. Only the stainless steel clamping frame, 50mm wide, is visible when installed. FFL is clear opening plus 202mm. Load rating class: K3 25

Pipework adaptors Adaptors and couplings are available to connect Wade products to pipework made by others T6 series Hub adaptor for caulk joint T1103 Push fit coupling BS 416/437 to Supersleve T12 series Copper to BS 416. Adaptor must be brazed/ soldered to copper pipe before connecting to BS 416 by means of a proprietary coupling T1501 MJ coupling BS 416 to plastic T1603 MJ coupling 75mm BS 416 to Ensign Connections Adaptor From To kg 2" BSP female 50mm cast iron caulk joint T601 0.6 3" BSP female 75mm cast iron caulk joint T602 2.6 4" BSP female 100mm cast iron caulk joint T603 3.2 100mm BS 416 or BS 437 100mm Supersleve T1103 0.2 50mm BS 416 50mm copper T1201 0.4 75mm BS 416 75mm copper T1202 0.6 100mm BS 416 100mm copper T1203 0.7 100mm BS 416 110mm plastic T1501 0.3 75mm BS 416 75mm DIN 19522 Ensign T1603 1.2 Threaded pipework adaptors A comprehensive range of adaptors, shown in the following table, is available to enable gully bodies with BSP threaded outlet to be connected speedily and effectively to all pipework in general use. To complete the connection a coupling may be required as indicated. Longer lengths, such as required to pass through a slab, can be made in 10mm increments up to 900mm (except T501, T502, T1702 and T1704). To specify/order add suffix and length (mm), eg. T103-250. T1702* Adaptor, plastic (ABS) T1704* Adaptor, plastic (ABS) Pipework system * Solvent weld socket. Nom dia. mm Body outlet BSP O.D. mm Length mm Material kg Required coupling Cast iron BS 416 50 2" T101 60 90 Mild steel, sherardized 0.5 Proprietary Cast iron BS 416 75 3" T102 87 90 Mild steel, sherardized 0.9 Proprietary Cast iron BS 416 100 4" T103 111 90 Cast iron 1.2 Proprietary Cast iron BS 416 150 6" T104 162 90 Cast iron 1.1 Proprietary Cast iron BS 437 100 4" T105 117 90 Cast iron 1.4 Proprietary Cast iron BS 437 150 6" T106 171 90 Cast iron 1.8 Proprietary Cast iron DIN19522 (Ensign + SMU) 50 2" T101 60 90 Mild steel, sherardized 0.5 Proprietary Cast iron DIN19522 (SMU) 75 3" T108 84 90 Mild steel, sherardized 0.7 Proprietary Cast iron DIN19522 (Ensign) 75 3" T102 87 90 Mild steel, sherardized 0.9 Wade T1603 Cast iron DIN19522 (Ensign + SMU) 100 4" T103 111 90 Cast iron 1.2 Proprietary Cast iron DIN19522 (Ensign + SMU) 150 6" T104 162 90 Cast iron 1.1 Proprietary Stainless steel (Europipe) 50 2" T1802 50 90 Plastic (ABS) 0.2 Proprietary Stainless steel (Europipe) 100 4" T302 110 120 Plastic (UPVC) 0.4 Proprietary Plastic 50 2" T1702* * 60 Plastic (ABS) 0.1 None Plastic 82 3" T301 82 140 Plastic (ABS) 0.2 Proprietary Plastic 110 4" T1704* * 126 Plastic (ABS) 0.2 None Plastic 160 6" T303 160 166 Plastic (ABS) 0.6 Proprietary HDPE 100 4" T103 111 90 Cast iron 1.2 Wade T1501 Clay (Supersleve) 100 4" T501 122 130 Cast iron 2.8 Proprietary Clay (Supersleve) 150 6" T502 178 130 Cast iron 4.6 Proprietary 26

Floor gullies and access covers Wade offers a comprehensive range of gullies with versions to suit different kinds of floor and floor finish, for connection to all pipework in general use, as shown on pages 4 to 35 A selection of floor gullies, access covers, and accessories. Super-Seal access cover in a tiled floor. Stainless steel gully with side inlets. Sliding access cover. (Patent pending) Watertight drainage in a vinyl covered timber floor. 27

Roof outlets Wade offers a range of roof outlets with versions for use with different types of roof construction, as shown on pages 36 to 41 A selection of roof outlets and accessories. WC224Z roof outlet with WG102 underdeck clamp and WT103 threaded pipework adaptor, in a warm roof with single membrane. WF105 parapet outlet connected to a WJ104 downspout nozzle in an installation with a single ply membrane. 28 WD204 roof outlet in an inverted roof.

Linear drainage Wade offers a range of gratings of stainless steel, nickel bronze, aluminium and cast iron for use in frames or stainless steel channel, as shown on pages 42 to 50 Stainless steel channel with Streamline stainless steel grating. Heavy duty bar grating designed for trolley wheel-loading. Stainless steel channel and grating meet the high standards of hygiene demanded in today s working environments. Channel profile SVF ensures watertight connection when used with flexible sheet floor covering such as vinyl. SS3080AC Mitred Streamline grating (patent pending). A selection of gratings. 29

Wade drainage products Wade drainage products are installed in and near all kinds of building, some examples of which are shown below A.E.L.T.C.C. Wimbledon. Chep Lap Kok Airport, Hong Kong. Drainage and access in a vinyl floor. A McDonalds Restaurant. The British Library. Drainage in block paving. Asda Store, Runcorn. Access covers in a marble floor. 30

Uni-Level non-trapped gullies Gullies for asphalt/composition finished floors Suitable for areas with an asphalt finish, subject to car and light commercial traffic Connections Bodies with threaded outlet are for connection to pipework by means of a threaded pipework adaptor shown on page 26. 305 dia. A A WB324 Gully Cast iron body with 220 dia. sherardized ductile iron grating 90 Vertical threaded outlet WB322 2" BSP WB323 3" BSP WB324 4" BSP B Horizontal threaded outlet A B WB332 2" BSP 119 145 WB333 3" BSP 119 145 WB334 4" BSP 183 90 235 dia. (Integral) Spigot outlet A WB302 50mm 238 WB303 75mm 165 WB304 100mm 190 A 350 dia. WB514 Gully Cast iron body with 320 sq. sherardized ductile iron grating Vertical threaded outlet A WB514 4" BSP 171 WB516 6" BSP 149 Vari-Level and direct connection gratings (Sherardized cast iron) Vari-Level version (illustrated) is for use with Vari-Level cast iron bodies shown on pages 10 to 14. Direct connection version is for use without a body and for connection to 100 mm pipework Cast iron BS 416 / DIN 19522 or PVC. With stainless steel asphalt membrane clamp Overall Vari-Level Direct con. K2501A K2591A 176 dia. 31

Gullies for unfinished floors (Bare concrete/screed) Multi-Level non-trapped gullies For use with Vari-Level bodies D2-D7 and GD, shown on pages 10 to 13 Cast iron body with hinged sherardized ductile iron grating. (F3 have stainless steel body) Load rating class: L15 Sherardized ductile iron grating Grating Collar Overall M101 C.M1 220 dia. Cast iron extension (optional) U301 For use with E series bodies shown below Load rating class: M125 Overall Overall Body Collar width Height F204 C.F2 396 x 396 338 max. 4" BSP F206 C.F2 396 x 396 338 max. 6" BSP F304 C.F3 450 x 450 357 max. 100mm F306 C.F3 450 x 450 357 max. 150mm Optional membrane clamping collar specify per table Load rating class: L15 Sherardized ductile iron grating Grating Collar Overall M301 C.E2 280 dia. Load rating class: L15 Sherardized ductile iron grating Grating Collar Overall M401 C.E2 270 sq. Cast iron body and frame with hinged stainless steel bar grating Cast iron body medium sump Height E204 4" BSP 125 E206 6" BSP 125 Stainless steel extension (optional) Cast iron body deep sump, optional side inlets Max 4" BSP (See page 9) Height E404 4" BSP 280 E406 6" BSP 280 Load rating class: D400 Overall Overall Body Collar width Height F214 C.F2 396 x 396 338 max. 4" BSP F216 C.F2 396 x 396 338 max. 6" BSP Optional membrane clamping collar specify per table Options Filter bucket stainless steel, add suffix B Removable bell trap U1704 (F304 only) U1706 (F306 only) U401 SS Options Filter bucket add suffix B to the Body Bolt-on funnel U502, U602. To specify/order Specify grating, collar and body s. Note clamping collar is optional for F2 and F3 series. Also available WD2 to WD7 series, Multi-Level non-trapped gullies see page 39 for details of roof outlets which are commonly used as floor gullies. K2501 Vari-Level grating See page 16. K2591 Direct connection grating See page 21. 32

Miscellaneous floor gullies Drainage of planting areas and roof garden Pool/Pit drainage L L Ductile iron grating with perforated stainless steel ballast guard P801 + length Use with bodies D10-D12 (page 11) 104 dia x L (Std.pipe) 200min. Copper dome with PVC standpipe P901 + length Use with bodies Vari-Level (page 10-14) 195 dia x H 40 Stainless steel P1001 Sheet or brush on P1002 All types (inc asphalt) Use with bodies C2-C5 (page 10) D10-D12 (page 11) L 370 x W 294 x H 277 Stainless steel body and grating for use in pools and pits requiring backflow protection Q801 100mm with backwater Q802 150mm valve BS 437 Pool overflow Stainless steel standpipe for use with Vari-Level bodies (page 10-14) 90 Gully Add suffix H for security versions Water depth 120 dia. x L (Water depth) K3201 Without cap K3202 With cap Water depth 155 dia. x L (Water depth) K3211 + length (mm) K3212 + length (mm) Water depth 162 dia. x L (Water depth) For tiles etc. For vinyl etc. Dimensions at FFL L 100 x W 150 x H 60 max. Cast iron body with nickel bronze grating Grating P1412 NB 2" BSP P1413 NB 3" BSP P1414 NB 4" BSP Dimensions at FFL L 100 x W 150 x H 60 max. Cast iron body with stainless steel grating Grating P1422 SS 2" BSP P1423 SS 3" BSP P1424 SS 4" BSP High capacity gullies Non-trapped unless stated L 717 x W 699 x H (see table) Stainless steel body with sherardized ductile iron grating H Q105 100mm BS 416 240 Q106 150mm BS 416 250 L 295 x W 295 x H 289 Cast iron body with nickel bronze grating Body finish Q301 4" BSP Lacquered Q302 4" BSP Plastic coated L 450 x W 450 x H 280 Trapped stainless steel body with hinged sher. ductile iron grating Q403 100mm BS 416 L 633 x W 220 x H 405 Trapped cast iron body with nickel bronze grating and nickel bronze sealed cover Q501 100mm BS 437 Gunmetal gullies For use in metal decks Trapped Non-trapped For tile or composition flooring For sheet floor covering For tile or composition flooring For sheet floor covering Height max. Dia. P403 75 391 325 P404 100 391 325 Height max. Dia. P413 75 391 325 P414 100 391 325 Height max. Dia. P301 75 228 230 con. Height max. Dia. P501 50 2"BSPT male 167 190 P502 50 Copper 167 190 33

Gully assemblies for sheet floor covering* For use in wet bathrooms and shower areas decked with sheet floor covering, such as vinyl, of a thickness up to 3.5mm. ABS plastic body with stainless steel or nickel bronze clamp collar and grating/cover/funnel 'P' trapped gully 50mm seal GV5 series 50mm socket outlet 1. Peripheral slot 2. Slotted grating 3. Security grating 4. Solid cover 5. Funnel GV5007 Dimensions shown are for GV5007 220 dia. 160 dia. Clamping collar Grating 104 50 56 dia. 105 (Invert) Removable dip tube Removable bucket Illustration no. Top material Version Load rating class GV5007 1 Stainless steel Grating (peripheral slot) K3 1.2 GV5103 2 Nickel bronze Grating (slotted) L15 1.5 GV5107 2 Stainless steel Grating (slotted) L15 1.0 GV5247 3 Stainless steel Security grating (4mm aperture) K3 1.0 GV5503 4 Nickel bronze Solid cover (gasketed) L15 1.9 GV5517 4 Stainless steel Solid cover (unsealed) L15 1.2 GV5803 5 Nickel bronze Funnel (tapered) 101 dia x 100H n/a 2.4 GV5817 5 Stainless steel Funnel (parallel) 101 dia x 101H n/a 1.7 GV5823 5 Nickel bronze Funnel (oval) 224L x 85W x 99H n/a 3.7 kg Options Suffix H Fitted with Pin Torx screws for security applications (not GV5007). Note: GV5247 has Pin Torx screws as standard. ][ Tapped to provide a direct connection for waste pipes specify 1¼", 1½", or 2" BSP (solid cover versions only). PB Made of polished bronze (available for nickel bronze versions only check availability). P Polished (GV5817 is polished as standard). Features Watertight clamping collar provides a water-tight seal between the flooring material and gully even when the grating is removed. Flow rate (grating and funnel versions) rate in excess of 40 l/min; comfortably exceeds the minimum rate of 24 l/min required by BS EN 274 for the discharge from a single shower head. Installation ideally suited for installation in timber or concrete floors or where space is limited. Future use gratings/covers may be replaced in case of change of use. Notes The gully must be supported and installed in accordance with instructions which accompany the product. Frequent cleaning will be necessary in applications where very high amounts of hair and other waste material are present. * See also Vari-Level (pages 16 18), direct connection (pages 21 25) and stainless steel gullies (pages 6 7) for other gullies for sheet floor covering. 34

GV6 series 110mm spigot outlet with 50mm reducer Gully assemblies for sheet floor covering* For use in wet bathrooms and shower areas decked with sheet floor covering, such as vinyl of a thickness up to 3.5mm. ABS plastic body with stainless steel or nickel bronze clamp collar and grating/cover/funnel Trapped gully with vertical outlet 50mm seal 1. Peripheral slot 2. Slotted grating 3. Security grating 4. Solid cover 5. Funnel GV6103 Dimensions shown are for GV6103 220 dia. 160 dia. Clamping collar Grating 157 103 50 Removable dip tube Removable bucket 56 dia. 110 dia. Illustration no. Top material Version Load rating class GV6007 1 Stainless steel Grating (peripheral slot) K3 1.2 GV6103 2 Nickel bronze Grating (slotted) L15 1.5 GV6107 2 Stainless steel Grating (slotted) L15 1.0 GV6247 3 Stainless steel Security grating (4mm aperture) K3 1.0 GV6503 4 Nickel bronze Solid cover (gasketed) L15 1.9 GV6517 4 Stainless steel Solid cover (unsealed) L15 1.2 GV6803 5 Nickel bronze Funnel (tapered) 101 dia x 100H n/a 2.4 GV6817 5 Stainless steel Funnel (parallel) 101 dia x 101H n/a 1.7 GV6823 5 Nickel bronze Funnel (oval) 224L x 85W x 99H n/a 3.7 kg Options Suffix H Fitted with Pin Torx screws for security applications (not GV6007). Note: GV6247 has Pin Torx screws as standard. ][ Tapped to provide a direct connection for waste pipes specify 1¼", 1½", or 2" BSP (solid cover versions only). PB Made of polished bronze (available for nickel bronze versions only check availability). P Polished (GV6817 is polished as standard). Features Watertight clamping collar provides a water-tight seal between the flooring material and gully even when the grating is removed. Flow rate (grating and funnel versions) rate in excess of 40 l/min; comfortably exceeds the minimum rate of 24 l/min required by BS EN 274 for the discharge from a single shower head. Installation ideally suited for installation in timber or concrete floors or where space is limited. Future use gratings/covers may be replaced in case of change of use. Notes The gully must be supported and installed in accordance with instructions which accompany the product. Frequent cleaning will be necessary in applications where very high amounts of hair and other waste material are present. * See also Vari-Level (pages 16 18), direct connection (pages 21 25) and stainless steel gullies (pages 6 7) for other gullies for sheet floor covering. 35

Roof outlets Installation guidelines The design of the layout of roof outlets should be in accordance with the recommendations given in BS EN 12056:3. Wade offers a range of roof outlets with versions for use with different types of roof construction (warm, cold, inverted, no fines screed) for installation in different types of deck (concrete, metal, wood) with different types of waterproofing membrane (mastic asphalt, built-up felt roofing, single ply), as shown on following pages. Cast iron bodies are available with medium sump or deep sump with choice of outlet and connection type, with polycarbonate dome or sherardized cast or ductile iron flat grating. Bodies with spigot outlet are for direct connection to pipework; versions with threaded outlet are for connection to pipework by means of a threaded pipework adaptor. Roof outlets should be placed at the roof low points to allow efficient flow of water to the outlets. Note For versions with bonded insulation jacket add suffix K to the For versions with integral PVC flange for use with PVC single ply membranes add suffix Z to the 1. Check dimensions 2. Fit adaptor, check outlet 3. Install body Prior to installation, check height of components to ensure compatibility with roof build-up, making allowances for the membrane thickness. 4. Dress membrane and clamp Where applicable, screw threaded pipework adaptor into body, using a suitable sealant to ensure the joint is watertight. Position body in roof deck and ensure outlet is accessible for pipework connection. 5. Install insulation Install body such that flange is flush or sub-flush with roof deck. Ensure body is fixed securely, either bonded or clamped to the deck if not cast-in. Use a suitable sealant on any threaded joints e.g. extension flange, to ensure a water-tight assembly. Note flange level is determined by roof build up. 6. Fit grating, apply finish Refer to membrane manufacturer s instructions. Prepare flange of body with suitable primer and apply membrane, dressing over flange and into sump of body. Position membrane clamping collar and secure to body using fixings supplied. Install any intermediate roof build-up (e.g. insulation) around outlets. Fit dome/grating using height adjustment where applicable to ensure grating is flush with roof finish. Apply roof finish around grating. 36

Roof outlets Typical installations Warm roof see page 38 and 41 clamping collar Extension flange Bearing pan (optional) Insulation Insulation Roof deck Roof deck Bonded insulation jacket Underdeck clamp (optional) Bonded insulation jacket Underdeck clamp (optional) Cold roof see page 39 and 41 Secured dome clamping collar Secured flat grating clamping collar Roof deck Roof deck Body Body Pipework adaptor (select separately) Underdeck clamp ( optional ) Inverted roof see page 39 and 41 Flat grating Slotted collar / membrane clamping collar Roof finish Insulation Roof deck clamping collar Gravel guard Roof finish Insulation Screed Roof deck Body Pipework adaptor (select separately) Body Underdeck clamp (optional) Parapet outlet see page 40 Downspout nozzle see page 40 Balcony outlet see page 40 Body clamping collar Grating Screed Downspout nozzle Gravel guard (optional) Grating clamping collar Rainwater downnpipe Grating Connecting threaded pipework adaptor Body Body 37

Roof outlets For warm roof Comprising cast iron body with sherardized ductile iron grating, polycarbonate dome, or stainless steel dome Medium sump For use with insulation thicknesses between 80mm and 100mm* For use with insulation thicknesses between 20mm and 135mm* 190 dia. dome 220 dia. grating 190 dia. dome 220 dia. grating Spigot outlet Vertical threaded outlet Spigot outlet Vertical threaded outlet Spigot outlet Vertical threaded outlet Spigot outlet Vertical threaded outlet WC202 50 WC203 75 WC204 100 WC222 2" BSP WC223 3" BSP WC224 4" BSP WC302 50 WC303 75 WC304 100 WC322 2" BSP WC323 3" BSP WC324 4" BSP WC402 50 WC403 75 WC404 100 WC422 2" BSP WC423 3" BSP WC424 4" BSP WC502 50 WC503 75 WC504 100 WC522 2" BSP WC523 3" BSP WC524 4" BSP Horizontal threaded outlet Horizontal threaded outlet WC232 2" BSP WC233 3" BSP WC234 4" BSP WC332 2" BSP WC333 3" BSP WC334 4" BSP Deep sump Vertical threaded outlet For use with insulation thicknesses between 80mm 115mm 190 dia. dome 320 sq. grating 310 dia. grating WC644 4" BSP WC646 6" BSP WC744 4" BSP WC746 6" BSP WC1044 4" BSP WC1046 6" BSP For use with insulation thicknesses between 20mm and 135mm 190 dia. dome 320 sq. grating 310 dia. grating WC814 WC816 4" BSP 6" BSP WC818 200mm WC914 WC916 4" BSP 6" BSP WC918 200mm WC1114 WC1116 4" BSP 6" BSP WC1118 200mm * For other thicknesses of insulation, please state and the insulation thickness. Polycarbonate dome for optional stainless steel dome, add suffix SS to. 200mm outlet is available only as spigot outlet. 38

Roof outlets For cold roof, inverted roof and no fines screed Comprising cast iron body with sherardized ductile iron grating, stainless steel grating, polycarbonate dome or stainless steel dome Cold roof Medium sump 190 dia. dome Vertical threaded outlet Spigot outlet Horizontal threaded outlet 220 dia. grating Vertical threaded outlet Spigot outlet Horizontal threaded outlet WB222 WB223 WB224 2" BSP 3" BSP 4" BSP WB202 50 WB203 75 WB204 100 WB232 WB233 WB234 2" BSP 3" BSP 4" BSP WB322 WB323 WB324 2" BSP 3" BSP 4" BSP WB302 50 WB303 75 WB304 100 WB332 WB333 WB334 2" BSP 3" BSP 4" BSP Deep sump 190 dia. dome Vertical threaded outlet 320 sq. grating Vertical threaded outlet 310 dia. grating Vertical threaded outlet WB414 WB416 4" BSP 6" BSP WB514 WB516 4" BSP 6" BSP WB614 WB616 4" BSP 6" BSP WB418 200mm WB518 200mm WB618 200mm Inverted roof and no fines screed Medium sump 220 dia. grating Vertical threaded outlet Spigot outlet Horizontal threaded outlet 224 sq. grating Vertical threaded outlet Spigot outlet Horizontal threaded outlet WD222 WD223 WD224 2" BSP 3" BSP 4" BSP WD202 50 WD203 75 WD204 100 WD232 WD233 WD234 2" BSP 3" BSP 4" BSP WD322 WD323 WD324 2" BSP 3" BSP 4" BSP WD302 50 WD303 75 WD304 100 WD332 WD333 WD334 2" BSP 3" BSP 4" BSP 200 sq. stainless steel grating Deep sump 220 dia. grating Vertical threaded outlet WD722 WD723 WD724 2" BSP 3" BSP 4" BSP Spigot outlet WD702 50 WD703 75 WD704 100 Horizontal threaded outlet WD732 WD733 WD734 2" BSP 3" BSP 4" BSP 224 sq. grating 190 dia. dome Vertical threaded outlet Notes These domed assemblies include a gravel guard (height of 150mm G1 or 200mm G2) Other heights can be made to special order advise height. WB222G1 2" BSP WB223G1 3" BSP WB224G1 4" BSP WB222G2 2" BSP WB223G2 3" BSP WB224G2 4" BSP Spigot outlet WB202G1 50 WB203G1 75 WB204G1 100 WB202G2 50 WB203G2 75 WB204G2 100 Horizontal threaded outlet 200 sq. stainless steel grating WB232G1 2" BSP WB233G1 3" BSP WB234G1 4" BSP WB232G2 2" BSP WB233G2 3" BSP WB234G2 4" BSP Vertical threaded outlet WD514 WD516 4" BSP 6" BSP WD518 200mm Vertical threaded outlet WD614 WD616 4" BSP 6" BSP WD618 200mm Vertical threaded outlet WD644 WD646 4" BSP 6" BSP WD648 200mm Polycarbonate dome for optional stainless steel dome, add suffix SS to. 200mm outlet is available only as spigot outlet. 39

Roof outlets Parapet and balcony outlets, downspout nozzles Parapet outlets Reversible cast iron body WF002-WF034 Series WF072-WF076 Series WF156 WF042-WF046 Series WF105-WF135 Series WF166 Options Stainless steel gravel guard add suffix G. Grade 316 (stainless steel grating versions) add suffix M. Downspout nozzles Cast gunmetal WF176 Grating Body material WF002 2" BSP Nickel bronze Cast iron WF003 3" BSP Nickel bronze Cast iron WF004 4" BSP Nickel bronze Cast iron WF012 2" BSP Aluminium Cast iron WF013 3" BSP Aluminium Cast iron WF014 4" BSP Aluminium Cast iron WF022 2" BSP Cast iron Cast iron WF023 3" BSP Cast iron Cast iron WF024 4" BSP Cast iron Cast iron WF032 2" BSP Stainless steel Cast iron WF033 3" BSP Stainless steel Cast iron WF034 4" BSP Stainless steel Cast iron WF042 2" BSP Stainless steel Cast iron WF043 3" BSP Stainless steel Cast iron WF044 4" BSP Stainless steel Cast iron WF046 6" BSP Stainless steel Cast iron WF072 2" BSP Stainless steel Cast iron WF073 3" BSP Stainless steel Cast iron WF074 4" BSP Stainless steel Cast iron WF076 6" BSP Stainless steel Cast iron WF105 4" BSP Nickel bronze PVC* WF115 4" BSP Aluminium PVC* WF125 4" BSP Cast iron PVC* WF135 4" BSP Stainless steel PVC* WF156 6" BSP Aluminium Cast iron WF166 6" BSP Aluminium Cast iron WF176 6" BSP Aluminium Cast iron * With PVC body for use with single ply membrane, see page 28 for illustration. Balcony outlets Cast iron WJ102 WJ103 WJ104 2" BSP 3" BSP 4" BSP WJ202 WJ203 2" BSP 3" BSP WF604 100mm BS416 WF704 100mm BS416 Outfall outlets Stainless steel grade 304, satin finish top hinged Overflow outlets Polypropylene Nickel bronze Connecting spigot Typical installation Max pipework dia. WJ302 62 WJ303 88 WJ304 115 Add suffix OF to a domed roof outlet (select from pages 38 and 39). N215 Inlet 2" BSP F Size Material U27xx* 2" BSP ABS U37xx* 3" BSP ABS U47xx* 4" BSP UPVC * xx Denotes length in cm please supply. See typical installation of downspout nozzle on page 37. 40

Roof outlets Accessories Gravel guard Stainless steel Medium sump Height WG406 150 WG408 200 Deep sump Height WH506 150 WH508 200 Non-standard height can be made to order Bearing pan Galv. mild steel Underdeck clamp Medium sump WG102 WG102SS Material Mild steel S/Steel Deep sump WH202 WH202SS Filter bucket Stainless steel Material Mild steel S/Steel Dome Stainless steel grade 304 Alternative to standard polycarbonate version. Add SS to of roof outlet. For grade 316 add SSM Extension piece Cast iron (inverted roof only) Medium sump Deep sump WG301 WH402 WD2-WD7 series WG201 WH301 WG301 WH402 Compatible with WC2-WC5, WB2-WB3, WD1-WD7 WC7, WC9, WB5 Height WG501 96 WG502 35 Bonded insulation jacket A factory fitted bonded insulation jacket is used to prevent condensation forming on the underside of a body. To specify/order add suffix K to the roof outlet. Threaded pipework adaptors A comprehensive range of adaptors, shown in the following table, is available to enable gully bodies with BSP threaded outlet to be connected speedily and effectively to all pipework in general use. To complete the connection a coupling may be required as indicated. Longer lengths, such as required to pass through a slab, can be made in 10mm increments up to 900mm. To specify/order and suffix and length (mm), eg. WT103-250. On request, adaptors may also be threaded both ends. For details, please contact our Technical Services Department. Threaded pipework adaptor Pipework Nom. dia. Body outlet Spec O.D. Length Required system mm BSP mm mm Material Weight coupling Cast iron BS 416 50 2" WT101 60 170 Mild steel, sherardized 1.0 Proprietary Cast iron BS 416 75 3" WT102 87 170 Mild steel, sherardized 1.7 Proprietary Cast iron BS 416 100 4" WT103 111 170 Cast iron 2.5 Proprietary Cast iron BS 416 150 6" WT104 162 170 Cast iron 4.0 Proprietary Cast iron BS 437 100 4" WT105 117 170 Cast iron 2.6 Proprietary Cast iron BS 437 150 6" WT106 171 170 Cast iron 4.1 Proprietary Cast iron DIN19522 (Ensign+SMU) 50 2" WT101 60 170 Mild steel, sherardized 1.0 Proprietary Cast iron DIN19522 (SMU) 75 3" WT108 84 170 Mild steel, sherardized 1.2 Proprietary Cast iron DIN19522 (Ensign) 75 3" WT102 87 170 Mild steel, sherardized 1.7 Wade T1603 Cast iron DIN19522 (Ensign+SMU) 100 4" WT103 111 170 Cast iron 2.5 Proprietary Cast iron DIN19522 (Ensign+SMU) 150 6" WT104 162 170 Cast iron 4.0 Proprietary Stainless steel (Europipe) 50 2" T1802 50 90 Plastic (ABS) 0.2 Proprietary Stainless steel (Europipe) 100 4" T302 110 120 Plastic (UPVC) 0.4 Proprietary Plastic 50 2" T1702* * 60 Plastic (ABS) 0.1 None Plastic 82 3" T301 82 140 Plastic (ABS) 0.2 Proprietary Plastic 110 4" T1704* * 126 Plastic (ABS) 0.2 None Plastic 160 6" T303 160 166 Plastic (ABS) 0.6 Proprietary HDPE 100 4" WT103 111 170 Cast iron 2.5 WadeT1501 *Solvent weld socket 41

Linear drainage Installation guidelines This is general information only, when installing in concrete; channel-specific instructions are supplied with the goods for use by the installer 1. Remove any gratings and clamping frames from channel. 2. Taking care not to twist, turn the channel upside down (base uppermost). 3. If there is more than one section to the channel, apply silicone sealant to jointing flange faces or fit rubber gaskets if supplied, and securely bolt sections together. 4. If connecting to a Wade gully, follow the instructions supplied. 8. lf not supplied, provide and insert spacer bars across channel at approx. 500mm centres. Spacer bars prevent channel being squeezed while backfill is being compacted and must not be removed until backfill is set. 9. Fix the channel into position by first grouting build-in ties and any adjustment legs firmly in place. 10. Taking care not to damage show surfaces, place heavy weights on top of the channel prior to pouring backfill to prevent any lift or movement. 11. Using concrete class C30/37 backfill around the channel ensuring that the concrete flows evenly under and around the channel such that no voids are formed. 5. Taking care not to twist, turn the channel the correct way up and lower it into the trench and into any installed gullies: ensure top edge of channel is flush with finished floor level, use the adjustment legs when supplied. 6. Bend the build-in ties as necessary. 7. Make the pipework joints below the channel. Note After positioning the channel it is recommended that a water test be undertaken to check that height is correct, that, where applicable the fall in the channel works effectively, that there are no leakages from the channel system and that there are no signs of deformation or damage to the channel which may have occured during installation. At this stage it may still be possible for any necessary rectification work to take place. Please consult our Technical Services Department if this situation arises. 12. Remove immediately any material which falls into the channel. 13. When concrete is set, remove spacer bars. 14. Fit gratings. 15. Clean channels and gratings with water and a suitable cleaning agent where necessary. Under no circumstances use metal scouring pads or wire wool as these will contaminate surfaces. Note Load classes given are based on channel being set in concrete class C30/37, to a level that fully supports the grating seat. For a lower load rating, lesser amounts and class of concrete may be suitable consult a structural engineer if advice is needed. 42

Linear drainage Installation guidelines continued Drainage channel profile SVF for use with flexible sheet floor covering The following additional notes/procedures apply: 1. Dress floor covering into channel and fix in accordance with flooring manufacturer's instructions. 2. Fit clamping frames and gratings. Drainage channels with perimeter angle frame The following additional notes/procedures apply: 1. The gap between the outside edge of the channel and the angle frame is covered with an adhesive tape to prevent debris filling up the gap during installation. Do not remove the tape until installation is complete. 2. When the channel is installed, lay the floor into the perimeter angle frame. 3. Once the floor is set, carefully remove the spacer bars between the angle frame and the channel using an angle grinder or similar. Note Do not remove the spacer bars before fitting the channel, as it would then be impossible to maintain the position of the frame relative to the channel. 4. Thoroughly clean the gap between the channel and angle frame, degrease and fill with a permanently elastic expansion joint sealant. If corrosive chemicals are likely to be present, consult sealant manufacturer on suitability. Typical installation in a vinyl covered floor. Channel profile SVF illustrated with SN12230 grating and UP702 filter bucket. Typical installation Channel outlets Some Wade floor gully bodies, trapped or untrapped, can be used with stainless steel drainage channel as illustrated. Please refer to our Linear Drainage catalogue for full details of options available. With D1004 non-trapped body and C.D10L membrane clamping collar. With G304 LD P trapped body. NEF channel and SS7200A5 grating with dropped sump and U1704 removable bell trap. 43

Linear drainage (BS EN1433 compliant) Channel gratings For use with channel shown on page 46 Stainless steel grade 304 For grade 316 add suffix M to the. 1 2 3 4 5 6 7 Streamline Illust. no Width Length Depth Aperture width Free area cm 2 /m Load class SS3080B5 1 82 500 20 5 375 B125 SS3135A5 1 135 500 20 5 740 A15 SS3135B5 1 135 500 30 5 740 B125 SS3150A5 1 152 500 20 5 810 A15 SS3150B5 1 152 500 30 5 810 B125 SS3080B1 1 82 1000 20 5 375 B125 SS3135A1 1 135 1000 20 5 740 A15 SS3135B1 1 135 1000 30 5 740 B125 SS3150A1 1 152 1000 20 5 810 A15 SS3150B1 1 152 1000 30 5 810 B125 SS3080BC 2 82 250x250 20 5 375 B125 SS3135AC 2 135 250x250 20 5 740 A15 SS3150AC 2 152 250x250 20 5 825 A15 Plain mesh Illust. no Width Length Depth Aperture width Free area cm 2 /m Load class *SS5135A5 3 134 500 20 23 sq. 1080 A15 *SS5135B5 3 134 500 30 23 sq. 1080 B125 SS5150A5 3 149 500 20 23 sq. 1205 A15 SS5150B5 3 149 500 30 23 sq. 1205 B125 SS5200A5 3 199 500 20 23 sq. 1620 A15 SS5200B5 3 199 500 30 23 sq. 1620 B125 SS5300A5 3 299 500 30 23 sq. 2440 A15 SS5300B5 3 299 500 40 23 sq. 2440 B125 Anti-slip mesh Illust. no Width Length Depth Aperture width Free area cm 2 /m Load class *SS7135A5 4 134 500 20 23 sq. 1080 A15 *SS7135B5 4 134 500 30 23 sq. 1080 B125 SS7150A5 4 149 500 20 23 sq. 1205 A15 SS7150B5 4 149 500 30 23 sq. 1205 B125 SS7200A5 4 199 500 20 23 sq. 1620 A15 SS7200B5 4 199 500 30 23 sq. 1620 B125 SS7300A5 4 299 500 30 23 sq. 2440 A15 SS7300B5 4 299 500 40 23 sq. 2440 B125 Perforated Illust. no Width Length Depth Aperture width Free area cm 2 /m Load class SS40135A1 5 134 1000 20 8 dia. 305 A15 SS41135A1 6 134 1000 20 8 sq. 280 A15 SS40150A1 5 149 1000 20 8 dia. 335 A15 SS41150A1 6 149 1000 20 8 sq. 315 A15 Bar Illust. no Width Length Depth Aperture width Free area cm 2 /m Load class SS6150B5 7 149 500 20 10 450 B125 SS6150C5 7 149 500 30 10 450 C250 SS6150D5 7 149 500 50 10 450 D400 * Aperture width reduced to 13mm on long edges Patent pending Option For security locking add suffix L to the. 44

Linear drainage (BS EN1433 compliant) Channel gratings For use with channel shown on page 46 Nickel bronze BS EN 1982 Satin finish 1 2 3 4 5 6 7 8 Standard aperture Illust. no Width Length Depth Aperture width Free area cm 2 /m Load class SN11230 1 60 495 15 10 172 B125 SN11430 2 60 495 15 16 sq. 184 B125 SN12220 3 115 544 10 8 365 B125 SN12230 3 134 662 15 8 425 A15 SN13240 4 186 485 20 10 725 A15 SN16330 8 300 483 15 12 1440 A15 Decorative Illust. Aperture Free area no Width Length Depth width cm 2 /m Load class SN23130 5 150 499 15 4 280 A15 SN23130 does not conform with BS EN 1433 because the aperture of 4mm is below the minimum of 5mm set in the standard. The grating conforms to CE regulations and bears the CE mark. Floral Illust. no Width Length Depth Aperture width Free area cm 2 /m Load class SN23930 6 149 499 15 15 max. 475 A15 SN25930 7 293 499 15 15 max. 950 A15 Aluminium BS EN 1706 Standard aperture Illust. no Width Length Depth Aperture width Free area cm 2 /m Load class SA12220 3 115 544 10 8 365 A15 SA12230 3 134 662 15 8 425 A15 SA16330 8 300 483 15 12 1440 A15 Cast iron BS EN 1561 Sherardized finish 9 10 11 12 13 14 15 Sherardized cast iron BS EN 1561 Illust. no Width Length Depth Aperture width Free area cm 2 /m Load class SC11230 9 60 497 16 10 172 B125 SC11430 10 60 500 15 16 sq. 184 B125 SC12220 11 115 544 10 8 365 A15 SC12330 12 143 387 12 11 425 B125 SC12431 13 149 497 15 16 sq. 470 B125 SC23930 14 149 499 16 15 max. 475 A15 Sherardized ductile iron BS EN 1563 and BS EN 1564 Illust. no Width Length Depth Aperture width Free area cm 2 /m Load class SG16460 15 305 610 26 16 1240 C250 SG15350 16 251 251 23 12 1180 B125 SG16250 17 305 305 26 9 970 A15 16 Option For security locking add suffix L to the (not SN11230, SN16330, SA16330 or SC11230). 17 45

Linear drainage (BS EN 1433 compliant) Stainless steel channel grade 304 1.5mm thickness (min.) Channel for use with gratings shown on pages 44 and 45 is available in a range of profiles, shown and described below. Side bars and folds are made so that the selected grating fits flush with the show edges. Stainless steel gratings are made to length; where multiple cast gratings do not fit the channel one or more gratings are cut. Load class is when installed with grating of same class in accordance with Wade installation instructions, see page 42. NE Narrow edge Load Class: B125 NEHD Narrow edge, heavy duty Load Class: C250 NEF* Narrow edge flanged Load Class: C250 RP Regular profile Load Class: C250 RE Return edge Load Class: C250 B position A Visible length at FFL F Size/type of pipework connection D Channel depth at outlet E spigot length To specify/order channel with grating quote: C Channel depth at ends; minimum = grating depth + 20mm Grating Channel profile General dimensions in mm (A to E above) connection details (F above / type of pipework system) Thickness of floor finish (where applicable). Gully body (optional select LD versions from pages 12, 14 see typical illustration on page 43). SE Support edge Load Class: C250 PA Perimeter angle frame Load Class: C250 SVF* For use with sheet floor covering such as vinyl. Min. grating width required is 80 mm Load Class: A15 SVFE* Extended flange with fixing holes, for use in timber deck Load Class: A15 Options (add to channel if required) Tile upstand designed for tiling over, recommended where channel is being installed close to a tiled wall, (see illustration opposite) 70mm high unless otherwise specified. Add suffix T. Dual-level drainage enables secondary drainage at membrane level. See opposite for details. Add suffix SSD or DSD (single or double). Support bar a solid stainless steel support bar helps prevent deformation or movement of channel in heavy load bearing areas. To specify/order add suffix S to the channel. (May be used with channel profiles: RP, RE, SE, PA or RPV). Grade 316 stainless steel add suffix M. Typical layouts * Please advise thickness of flooring RPV* Profile RP is available with a factory fitted PVC angle edging strip to which sheet floor covering can be butt welded at the time of installation; such channel is particularly suited to heavy duty applications Load Class: C250 Straight section T section L section U section 46

Linear drainage Stainless steel channel grade 304 Dual level drainage channel Provides primary drainage at finished floor level plus secondary drainage at membrane level. Load rating is one class lower than selected channel profile, except HC, HCE, HSC, HSCE, SVF and SVFE which are unchanged. Secondary drainage is available with the channel profiles shown on pages 46 and 48, for use with gratings shown on pages 44 45. To specify/order: Grating Channel profile Secondary drainage SSD or DSD add to channel General dimensions in mm connection details Flange depth from finished floor level Gully body (if required) Typical installations Tile Grating Sand/bedding Pavior Grating Sand/bedding Pavior Screed Drainage slots Geo-textile membrane Geo-textile membrane Drainage slots Geo-textile membrane Single secondary drainage (SSD) with channel profile NE. Double secondary drainage (DSD) with channel profile NE. Tile upstand For tiling over, or for use with other finishes and/or membrane where channel is being installed close to a tiled wall. 70mm high unless specified. Available with all channel profiles shown opposite add suffix T to specify. SVFT channel (SVF with optional tile upstand) and SS40135A1 grating. 47

Linear drainage (BS EN 1433 Compliant) Stainless steel slotted channel grade 304 Hidden channel Hidden channels are suited for draining large areas finished with block paving and can be designed to accommodate a range of paving thicknesses and flow rate requirements. Can also be produced as curved channels. Please contact our Technical Services Department with details, preferably with CAD. A A A A : HC Typical installation : HSC With non-removable toe bar. HC channel with integral stainless steel gully. (Recessed cover shown; can also be supplied with a grating if required). Covers are also available with spigot upstand for connection to rainwater pipework. : HCE Designed for use against a wall. : HSCE Designed for use against a wall. With non-removable toe bar. Features Paving depth from 15mm. The base of the channel is flat for depth up to 110mm, deeper versions have a V base. Slot width 5mm to 18mm, or 2x6mm with toe bar. Easily cleaned by directing jet of water along the channel towards the outlet. Can be combined with Wade gullies, recessed access covers and channel gratings. Load class A15 (depth A < 75mm), B125 (depth A > 75mm). Dual-level drainage available if required add suffix DSD or SSD to. To specify/order : HC, HSC, HCE or HSCE, length of channel, paving depth (A), channel depth, slot width, position and type of outlet, options. Supaslot channel SL SSL Suitable for large areas with low volumes of waste water such as in abattoirs, butcheries, dairies, breweries etc. With non-removable toe bar. Features Depth from 65mm to 180mm with or without fall. Slot width 18mm. (2x6mm on SSL). Easily cleaned by directing jet of water along the channel towards the outlet. Can be combined with Wade gullies and channel gratings. Load class: B125. To specify/order SL, SSL or HL, length of channel, position and diameter of outlet. HL Designed for use against a wall. 48

Linear drainage (BS EN 1433 Compliant) Dropped sumps and Jubilee modular system Stainless steel dropped sumps for channel Q27DS Q28DS Channel is available with a dropped sump welded to the channel base to help improve drainage and to allow an optional large stainless steel filter bucket and/or fitting of a removable trap. Note: Minimum channel base width to be equal to or greater than the sump top dimension. 255 Gasket seal 110 110 O.D. 185 dia. 185 60 185 dia. Optional side inlets maximum 2" BSP Option N not available 110 O.D. Optional side inlets maximum 2" BSP Versions of the style of Q10, Q12, Q13 and Q14 bodies shown on page 7, are made to order though the width of the grating (min. 200mm wide) in the channel above is a defining factor. Generally, it is more cost effective to increase the width of the entire channel and grating to match the sump, as opposed to boxing out. Jubilee modular system Channel of grade 304 stainless steel, with gratings of sherardized ductile iron. For use in unfinished floors such as in factories, plant rooms and service areas. Features Security locking deters unauthorised removal of gratings. Modular parts enable forming of short runs, junctions and corners. 250 m 2 drained per single outlet (based on B.R.E. rainfall figures of 75mm/hr). One outlet recommended for every 20 gratings. Gratings 305mm sq. Load class: B125. S4700 S4701 S4702 S4703 S4706 S4724 S4733 S4791 S4792 Height Section with single grating and 4" BSP outlet Section with single grating Section with 2 gratings Section with 3 gratings Section with 6 gratings 'T' Section with 4 gratings 'L' Section with 3 gratings Jointing piece Stop end To specify/order Each straight section must be in multiples of 305mm. After channel layout is decided select appropriate s with quantities of each item required. Patent No. 2 209 782. 49

Linear drainage (BS EN 1433 Compliant) Channel firefighting lift, angle frame and tree grille Channel and grating for firefighting lift Stainless steel grade 304 To prevent water, such as from a sprinkler, entering a lift well. Features Will deal with flow of 25 l/s in accordance with BS 9999. Streamline,135mm wide gratings are secured in the channel leaving a peripheral slot 10mm wide. Channel has two 150 mm outlets evenly spaced. Load class: A15. To specify/order : S4800 and lengths/layout of channel. Angle frame Stainless steel grade 304 For use over pre-formed channels, with gratings shown on pages 44 to 45. Features Load class: C250 or lower dependant on grating load class. To specify/order Specify Angle frame, of grating, and lengths/layout required. Tree grille 321 145 992 For use in shopping precincts or similar areas subject to pedestrian traffic. Features Gratings of nickel bronze set in frames of stainless steel grade 304. 8 gratings set in 2 sections allow fitting around an existing tree. Suitable for tree trunks up to 300mm dia. Matches decorative channel grating SN23130. Load class: A15. To specify/order : S4604. 411 50

Non-freeze water points and interceptors Water Points provide an external water source for plant watering, area cleaning, vehicle wash down and similar activities. The product is designed to be installed with the valve seal located inside a building, whilst the on/off control mechanism and hose connections are outside; when the valve is turned off, water drains out from the unit so that freezing cannot occur. Made to suit a given wall thickness the product can be supplied with a wall box with optional locking cover to deter unauthorised access. The Wade non-freeze water point is a UK Water Byelaws Scheme Approved Product YA1 3/4" BSP inlet YA2 11/4" BSP backnut Wall thickness 70mm min. available in 10mm increments 58 43 Dia. 95 x 43 Wall thickness 130mm min. available in 10mm increments 53 68 6 Operating key 1/2" Brass quick tap connector 3/4" BSP connection 7 110 64 32 50 115 Cautionary note Water points are non-freeze only when installed in the horizontal position, and are suitable for use only at normal mains supply pressure (up to 10 bar maximum). 150 x 90 WADE 61 50 170 Option Locking add suffix L. YA3 Wall thickness 130mm min. available in 10mm increments 70 Hinged cover Wall box 110 YA101+ wall thickness mm YA211+ wall thickness mm YA212+ wall thickness mm YA213+ wall thickness mm YA304+ wall thickness mm YA316+ wall thickness mm Wall box material/finish Without wall box Aluminium white epoxy coated Nickel bronze satin Gunmetal satin Stainless steel grade 304 satin Stainless steel grade 316 satin Hinged cover Wall box 61 50 170 Stainless Steel interceptors grade 304 Sediment interceptors Sediment interceptors are used to help prevent blockages where solids such as food scraps, hair, plaster, sediment etc. are discharged into drain lines. Bucket lifting handle Fastener 2" BSP Inlet 430 105 Flow rate I/sec. 390 sq. Solids collector 5740 0.4 Bucket stainless steel 5750 0.4 Bag polyester Sealed removable cover 125 2" BSP Sediment bucket or filter bag Note Minimum clearance above cover of 450mm is required for removal of bucket/bag. Oil interceptors Oil interceptors are installed in drain lines to help prevent the pollution of rivers, streams, drainage systems and water treatment plants. Units are used where spillages of oil or diesel could occur such as garages, transport workshops, diesel re-fuelling and storage areas, and where vehicles or plant are washed down or steam cleaned. Oil Interceptors are not suitable for petrol and volatile liquids. To specify/order Select the appropriate code from the table and add the required C dimension, e.g. for oil interceptor to accept a flow 3.5 l/sec. and having a C dimension of 250mm. Specify 6360, C dimension = 250mm. Max flow Inlet/outlet rate I/sec. B.S.P. Length mm Width mm C D 368 specified on order* 6330 1.9 4" 594 382 To be 6360 3.8 4" 775 482 432 6380 5.7 4" 988 669 419 C dimension is from top of cover to centre of inlet. D dimension is from bottom of interceptor to centre of inlet. Note *Minimum C dimension available is 150mm, larger dimensions should be specified in increments of 10mm. Larger s of oil interceptors are available, please contact our Technical Services Department with details for a quotation. 51

Stainless steel grease converters Installation A Wade Actimatic Grease Converter provides a natural, safe and environmentally friendly means of permanently converting grease to bio-degradable products. Types of installation In powder or liquid form, Wade Actimatic is a bacterial product (not enzyme), which maintains a micro-biological culture within the grease converter to deal with kitchen effluent. Floor standing (standard and low profile models) Fully recessed in ground floor (standard invert models) Fully recessed in ground floor (deep invert models) Fully recessed in intermediate floor (hanger type) Installation guidelines Wade Actimatic Grease Converters are designed to be installed in existing or new kitchens, at restaurants, canteens, hotels, hospitals, etc., and also at commercial or industrial premises where food is cooked, prepared or processed. They are not suitable for use with dedicated chicken rotisserie ovens unless special housekeeping measures are taken, including the introduction of water. There is no optimum distance between the last fixture and the converter; it is generally accepted that pipework longer than 8 metres may allow grease to solidify before it reaches the converter. Waste disposal units may discharge into a grease converter, but this practice is not advisable because frequent cleaning out will be necessary. Waste from vegetable peelers must be filtered before discharging. Certain cleaning agents (Chlorine, strong caustics, bleach etc.) in concentrated form, have a detrimental effect, and should not be discharged into a grease converter. Installations may require prior approval from the Local Authority Environmental Health Department. Wade Actimatic Grease Converters satisfy current Building Regulations/Standards in the U.K., and meet requirements of drainage systems designed in accordance with BS EN 12056-1: 2000. Threaded pipework adaptors for connecting to different types and s of pipework are shown on page 26. Note Do not reduce the stated inlet or outlet otherwise blockages could occur. Independent product assessment In 1989 Wade became the first manufacturer of grease converters to be awarded an Agrément Certificate. Grade 316 stainless steel Add suffix M to ; a plain cover is supplied with grade 316 versions, if anti-slip cover is required add suffix MAS (anti-slip cover grade 304). Note 6200 series models have covers with no dosing plug or rodding access. 52

Stainless steel grease converters How to select and grease converters To determine the optimum of converter to be used, account must be taken of the volume of fixtures discharging into the converter. Use the table below to calculate total volume by entering the quantity of each fixture, multiply by the volume shown and enter as Total Vol.; finally, add up your answers. Type of fixture Approx. (mm) Approx. vol. (litres) Quantity Total vol. (litres) Handwash sink 300 dia. x 180 deep 12 Domestic single sink 450 x 350 x 200 32 Domestic double sink (450 x 350 x 200) x 2 64 Commercial sink 600 x 450 x 300 81 Double commercial sink (600 x 450 x 300) x 2 162 Commercial potwash sink 760 x 500 x 380 144 Tilting kettle 150 Small dishwasher pipe 32 dia. 185 Medium dishwasher pipe 40 dia. 235 Large diswasher pipe 50 dia. 350 Other fixtures Total volume of fixtures (litres) 6000 series 6200 series A C B A G C B F 150 min. 200 min. 140 75 2" BSP vent pipe E E D D 200 connection (Vent to atmosphere if required) After selecting the appropriate type of installation, and calculating the total volume of fixtures, select the from the table below and add the required C dimension, e.g. for Converter to serve fixtures with a total volume of 325 litres and having a C dimension of 400mm, Specify: 6060XT C = 400mm Type of installation Floor standing Low profile Floor standing Standard invert Fully recessed ground floor Deep invert Fully recessed ground floor deep invert Large capacity Fully recessed intermediate floor Hanger type Max.total vol. of fixtures in Ltrs. In/Oulet BSP inches A mm B mm C mm Load class 160 6020LR 4 775 482 150 180 330 A15 160 6022LR 2 775 482 150 180 330 A15 290 6032LR 2 988 669 150 180 330 A15 290 6035LR 4 988 669 150 180 330 A15 210 6030 4 594 382 150 368 518 A15 410 6060 4 775 482 150 432 582 A15 625 6080 4 988 669 150 419 569 A15 210 6030XT 4 594 382 368 A15 410 6060XT 4 775 482 432 A15 625 6080XT 4 988 669 419 A15 1250 6215 6 1516 953 737 482 775 D400 2100 6225 6 1869 1142 940 482 775 D400 210 6030H 4 594 382 368 A15 410 6060H 4 775 482 432 A15 625 6080H 4 988 669 419 A15 To be specified on order D mm E mm F mm G mm Note: Dimensions show are for guidance only please contact us to confirm actual dimensions before ordering. For the hanger types listed, the dimension from finished floor level to the underside of the hanger frame (normally slab level) is adjustable on site from 35mm min to 75mm max. Automatic dosing system A mains powered dispenser unit is available for use with Actimatic Liquid. The unit automatically doses the converter with diluted Actimatic Liquid once daily at a time selected by the user. The system, once set, requires only monthly attention to replenish the liquid supply, and is suitable for use in most new and existing drainage systems. A warning light and audible alarm indicates low level of liquid. N.B. In practice fixtures do not all discharge at the full rate simultaneously. This has been allowed for and the table enables the correct grease converter to be selected. In abnormally high or dump situations contact our Technical Services Department. Options: D400 Heavy duty cover add suffix HD To specify/order : ADU Automatic Dosing Unit : AL1 Actimatic Liquid ( 1 ltr.) Options: Wall mounting bracket for storage drum made of grade 304 stainless steel with large radiussed corners to facilitate cleaning add suffix MB to. 53

Materials and maintenance Materials and finish of Wade products, described below, are selected to provide lasting performance and to blend with surroundings. The products require the minimum of maintenance, but periodic inspection should be carried out to ensure absence of matter which could impede drainage. Measures set out below will sustain appearance and prolong service life. ABS Used for bodies, dip tubes, extensions and spigot adaptors. A cost effective material. Maximum continuous operating temperature of 75 C. Cast aluminium BS EN 1706 Used for parapet and channel gratings. An alloy chosen for its chemical resistance and durability. Cast iron BS EN 1561 Used for bodies, membrane clamping collars, spigot adaptors and accessories such as extensions. A widely used metal in the drainage industry, its resistance to corrosion permits extended use under extreme conditions. Castings are coated with a high grade lacquer paint applied by full immersion dip to provide internal and external surface coverage. Paint will gradually wear off and is replaceable; oxidisation (surface rusting) is a natural process which does not weaken the material. A zinc anti-corrosion coating is applied to certain castings by sherardizing. Ductile iron BS EN 1563 and BS EN 1564 Used only for gratings. A casting with the ductility of steel, yet with more than twice the tensile strength of cast iron. A zinc anti-corrosion coating is applied by sherardizing. Mild steel Used for adjustable bearing pans and raising tubes. A cost effective material to which a zinc anti-corrosion material is applied by galvanising or sherardizing. Nickel bronze BS EN 1982 Satin finish Used for gratings, covers and funnels. A cast alloy with a fine grain effect which blends well with most floor finishes. The satin finish is generally maintained by the slight abrasive action of passing traffic. In unused areas the material will gradually tarnish. To restore lustre, apply a plain nylon scouring pad (not soap-filled) in the direction of the grain. Note Avoid covering nickel bronze items with plastic sheeting after installation, otherwise blackening may occur. Nylon 6 Used for bottle trap and filter bucket. Chosen for its toughness and durability. Maximum continuous operating temperature of 180 C. Polished bronze BS EN 1982 Used for gratings, covers and funnels. A cast alloy suited for finished floors where the rich, bronze colour complements the decor. The mirror finish is produced by polishing. If left alone polished bronze will gradually tarnish. To restore lustre, use metal polish and buff with a cloth. The mirror finish must not be treated with any abrasive cleaning material otherwise the surface will be permanently scratched. Polycarbonate Used for roof outlet domes. A polycarbonate/abs blend which offers durability, high impact strength and long term resistance to ultraviolet light. Polypropylene Used for the removable trap in stainless steel gullies. Maximum continuous operating temperature of 100 C. PVC Used for roof outlet body versions for use with PVC single ply membranes. This material enables a waterproof joint to be produced on site. Stainless steel Austenitic grade 304 and 316 Used for bodies, gratings, funnels, access covers, filter buckets and fixings. A corrosion-resistant metal containing significant amounts of nickel and chromium; AISI grade 304 stainless steel is used as standard, which is suitable for general use in and around buildings including most coastal locations. In applications such as swimming pools or having an aggressive atmosphere, grade 316 is recommended and is available on request. An even higher grade may be required for applications in highly corrosive environments including where exposure to seawater may be anticipated. Clean with soap and warm water rinse and wipe dry. Gratings may also be cleaned in certain dishwashers. Under no circumstances treat with metal scouring pads, metal scrapers or wire wool as these will contaminate surfaces leaving rust spots. 54

index Page ADU, AL1 53 Angle frame 50 B5 10 C 15 C2 - C5 10 D2 - D7 10 D10 - D12 11 DSD 47 E2, E4 32 F2, F3 32 G1 - G10 12 GC1 13 GD1 13 GP 13 GV5-6 34-35 H1 - H2 12 HC, HCE, HSC, HSCE 48 HL 48 J2 13 K Jacket 41 K18 16, 23 K19 21, 23 K20 21 K21 - K22 16, 17, 21, 23 K23 16, 17, 22, 23 K24 16, 17, 21, 23 K25 16, 21, 31 K26, K27 17, 21 K28, K29 16, 23 K31 17, 21 K32 33 K33 17, 21 K34 16, 17, 21, 23 K35 - K36 16, 23 K51 18, 24, 25 K52 - K53 18, 24, 25 K54 18, 24 K55 18, 24, 25 K56 18, 24, 25 K57 - K58 18, 24 L19 22, 23 L20 22 L21 16, 17, 22, 23 Page L22 17, 22 L23 17, 22 L24 17, 22 L25 16, 17, 21, 22 L26 16, 21 L27 16, 23 L28 17, 21 L29 16, 23 L30 17, 22 L31 - L37 16, 23 L51, L52 18, 24 L53 16-18, 22-25 L54 17, 18, 22, 24 L55 18, 24, 25 L56, L57 18, 24 L58 18, 25 M1 - M4 32 N1 22 N2 - N4 22, 25 N215 40 NE, NEF, NEHD 46 P3 - P5 33 P8 - P10 33 P14 33 PA 46 QB 14 QG 14 Q1 - Q5, Q8 33 Q6, Q9 8 Q10 - Q14 7 Q23 - Q28 6 Q42 - Q93 6, 7 R3 - R6, R8 25 RE 46 RP, RPV 46 RS 25 SA 45 SC 45 SD 11 SE 46 SG 45 SL, SSL 48 SN 45 Page SS 44 SSD 47 SVF, SVFE 46 S47 49 S48 50 T1 - T6 26 T7 - T9 20 T11 - T12 26 T13 - T14 19 T15 - T18 26 TP7 20 U1 - U2 19 U3 - U4 32 U5 - U7 19 U9 20 U11 - U12 19 U13 20 U14 19 U15 - U16 20 U18 20 U27-U47 40 U52 6 UP 19 UX 19 WB2 39 WB3 31, 39 WB4 39 WB5 31, 39 WB6 39 WC 38 WD 39 WF 40 WG - WH 41 WJ 40 WT 41 YA 51 3100 38, 39, 41 3400 38, 39, 41 3410 39, 41 5740-5750 51 6020-6225 52, 53 6330-6380 51 55

About Wade Visit our website for online versions of our product catalogue, price list, conditions of sale, news, job opportunities, Wade-CAD, Wade-BIM and PDF format technical handbooks. Wade-CAD is for users who require drawings of Wade products; files are in both DXF and AutoCAD DWG format. Wade-BIM is our library of BIM 3D models available for a range of products in Revit format. Other Wade literature Service Product information and technical advice are available from the Wade Technical Services Department at Halstead, Essex, from Wade Technical Consultants located throughout the UK and from selected distributors throughout the world. A computeraided design service is available free of charge for layouts and assemblies of Wade products. Warranty The Company warrants its products to be free from defects in material and workmanship for a period of 12 months from the date of delivery. The Company s obligation under this warranty is limited, at its option, to the repair or replacement, free of charge, or refund of the net invoiced price of any part found to be defective, and which, in the Company s opinion, has not been subject to undue wear and tear, accident, alteration, abuse or misuse. Consequential damages are expressly disclaimed. Technical advice from Wade International Limited, whether verbal, in writing or by way of trials, is given in good faith but without warranty. The application, use and installation of the Company s products are beyond the control of the Company, and the purchaser is solely responsible for ensuring that goods are fit for any particular purpose. In line with the Company s policy of continual research and development, product specifications and availability are subject to change or withdrawal without prior notice. Dimensions In line with general practice all dimensions shown are nominal. Dimensions are generally given in mm (other units are specified). QUALITY BY TRADITION PERFORMANCE BY DESIGN Wade International Ltd. Third Avenue HALSTEAD Essex CO9 2SX UK Telephone: +44(0)1787 475151 Facsimile: +44(0)1787 475579 e-mail: sales@wade.eu web site: www.wade.eu