SECTION SOIL AND WASTE SYSTEMS
|
|
- Martha Maxwell
- 7 years ago
- Views:
Transcription
1 SECTION PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division-1 Specification sections, apply to work of this section. B. Division-15 Basic Mechanical Materials and Methods sections apply to work of this section DESCRIPTION OF WORK A. Extent of soil and waste systems work, is indicated on drawings and schedules, and by requirements of this section. B. Applications for soil and waste piping systems include the 1. Aboveground soil, waste and vent piping within buildings, including soil stacks, vent stacks, horizontal branches, traps, and connections to fixtures and drains. 2. Underground building drain piping including mains, branches, traps, back water valves, connections to fixtures and drains, and connections to stacks, terminating at connection to sanitary sewers outside inner face of foundation wall. C. Refer to appropriate Division-15 sections for exterior sanitary sewer system required in conjunction with soil and waste systems; not work of this section. D. Insulation for soil and waste systems is specified in applicable Division-15 sections, and is included as work of this section. E. Trenching and backfilling required in conjunction with underground building drain piping is specified in applicable Division-15 sections and is included as work of this section. F. Refer to other Division-15 sections for sump pumps and sewage ejectors; not work of this section QUALITY ASSURANCE A. Manufacturer's Qualifications: Firms regularly engaged in manufacture of soil and waste systems products of types, materials and sizes required, whose products have been in satisfactory use in similar service for not less than 10 years. B. Installer's Qualifications: Firm with at least 10 years of successful installation experience on projects with soil and waste systems work similar to that required for project. C. Codes and Standards: 1. Plumbing Code Compliance: Comply with applicable portions of State and Local Plumbing Codes pertaining to plumbing materials, construction and installation of products. 2. ANSI Compliance: Comply with applicable ANSI standards pertaining to materials, products, and installation of soil and waste systems. 3. PDI Compliance: Comply with applicable PDI standards pertaining to products and installation of soil and waste systems SUBMITTALS CD Pricing/Permit; April 24,
2 A. Product Data: Submit manufacturer's technical product data for soil and waste systems materials and products. B. Record Drawings: At project closeout, submit record drawings of installed soil and waste systems, in accordance with requirements of Division 1. C. Maintenance Data: Submit maintenance data and parts lists for soil and waste systems materials and products. Include this data, product data, and record drawings in maintenance manual; in accordance with requirements of Division 1. PART 2 - PRODUCTS 2.01 MATERIALS AND PRODUCTS A. General: Provide piping materials and factory-fabricated piping products of sizes, types, pressure ratings, and capacities as indicated. Where not indicated, provide proper selection as determined by Installer to comply with installation requirements. Provide sizes and types matching piping and equipment connections; provide fittings of materials which match pipe materials used in soil and waste systems. Where more than one type of materials or product is indicated, selection is Installer's option BASIC PIPES AND PIPE FITTINGS A. General: Provide pipes and pipe fittings complying with Division-15 Basic Mechanical Materials and Methods section "Pipes and Pipe Fittings," in accordance with the following listing: B. Above Ground Soil, Waste, and Vent Piping: 1. Tube Size 8" and Smaller: Copper tube; Type DWV; Cast-bronze fittings, drainage pattern, solder-joint. 2. Pipe Size 15" and Smaller: Cast-iron hub-and-spigot soil pipe; service weight; Cast-iron, hub-and-spigot soil pipe fittings, compression gasket joints. 3. Pipe Size 8" and Smaller: Hubless cast-iron soil pipe; Service weight; Hubless cast-iron soil pipe fittings, hubless joints. 4. Pipe size 8 and smaller: Plastic pipe and fittings according to the Minnesota plumbing code section except where otherwise noted below. For use where no horizontal drain may exceed 35 feet in total length and no stack may exceed 35 ft in total height. Schedule 40 unthreaded. For use in chemical use areas. Plastic pipe not allowed in plenum spaces, parking garage, office ceiling spaces, corridors, mechanical rooms, electrical rooms, elevators, vestibules, stair wells, exposed areas, Plastic joints installed with color coded solvent and primer according to MN Plumbing Code C. Underground Building Drain Piping: 1. Pipe Size 15" and Smaller: Cast-iron hub-and-spigot soil pipe; Cast-iron hub-and-spigot soil pipe fittings, compression gasket joints. 2. Pipe size 10 and Smaller: No-Hub cast iron soil pipe, service weight, hubless cast iron soil pipe fittings, no-hub wide band underground joint assembly. 3. Pipe size 15 and smaller: Plastic pipe and fittings according to the Minnesota plumbing code section Schedule 40 unthreaded. Plastic pipe not allowed in plenum spaces, and exposed locations. Plastic pipe to be used in chemical use areas. D. Underground Building Drain Piping Sleeve Passing Through Walls: CD Pricing/Permit; April 24,
3 1. Pipe Sleeve Size 15" and Smaller: Ductile iron pipe, class 150; cast iron hub-andspigot pipe fittings, compression gasket joints. Note: Ductile iron pipe sleeve shall be installed through any below grade foundation wall or pipe tunnel wall and for a minimum distance of five feet either side of the wall BASIC PIPING SPECIALTIES A. General: Provide piping specialties complying with Division-15 Basic Mechanical Materials and Methods section "Piping Specialties," in accordance with the following listing: 1. Pipe Escutcheons. 2. Mechanical Sleeve Seals. 3. Fire Barrier Penetration Seals. 4. Drip Pans. 5. Pipe Sleeves. 6. Sleeve Seals FROST-PROOF VENT CAPS A. General: Provide frost-proof vent caps with 1" air space between outside of vent pipe and inside of flashing collar extension. Construct of galvanized iron, copper, or lead-coated copper. B. Manufacturer: Subject to compliance with requirements, provide frost-proof vent caps of one of the 1. F.J. Moore Mfg. Co BASIC SUPPORTS AND ANCHORS A. General: Provide supports and anchors complying with Division-15 Basic Mechanical Materials and Methods section "Supports and Anchors" in accordance with the following listing: 1. Adjustable steel clevis hangers, steel pipe clamps, and pipe saddle supports for horizontal piping hangers and supports. 2. Two-bolt riser clamps for vertical piping supports. 3. Concrete inserts, C-clamps, and steel brackets for building attachments BACKWATER VALVES A. General: Provide cast-iron body, bronze fitted backwater valve assembly. Hang flapper in such manner to provide maximum 1/4" clearance between flapper and seat for air circulation. Provide ends to suit piping material; bolted cover. B. Available Manufacturers: Subject to compliance with requirements, manufacturers offering backwater valves which may be incorporated in the work include, but are not limited to, the C. Manufacturer: Subject to compliance with requirements, provide backwater valves of one of the 3. Smith (Jay R.) Mfg. Co. 4. Tyler Pipe; Subs. of Tyler Corp. 5. Watts Drainage Products, Inc. 6. Zurn Industries Inc.; Hydromechanics Div CD Pricing/Permit; April 24,
4 2.08 EXPANSION JOINTS A. General: Provide cast-iron body expansion joints with adjustable bronze sleeve, bronze bolts with wing nuts; for vertical installation only. B. Manufacturer: Subject to compliance with requirements, provide expansion joints of one of the 3. Smith (Jay R.) Mfg. Co. 4. Tyler Pipe; Subs. of Tyler Corp. 5. Zurn Industries Inc.; Hydromechanics Div DRAINAGE PIPING PRODUCTS A. General: Provide factory-fabricated drainage piping products of size and type indicated. Where not indicated, provide proper selection as determined by Installer to comply with installation requirements and governing regulations. B. Cleanout Plugs: Cast-bronze or brass, threads complying with ANSI B2.1, countersunk head. C. Floor Cleanouts: Cast-iron body and frame; cleanout plug; adjustable round top as follows: 1. Nickel-Bronze Top: Manufacturers standard cast unit of the pattern indicated: a. Pattern: Exposed rim type, with recess to receive 1/8" thick resilient floor finish. b. Pattern: Exposed rim type, with recess to receive 1" thick terrazzo floor finish. c. Pattern: Exposed finish type, standard mill finish. d. Pattern: Exposed flush type, standard non-slip scored or abrasive finish. 2. Cast-Iron Top: Manufactured standard cast iron uit of the pattern indicated: a. Pattern: Exposed flush type, standard mill finish. b. Pattern: Exposed flush type, standard non-slip scored or abrasive finish. D. Wall Cleanouts: Cast-iron body adaptable to pipe with cast-bronze or brass cleanout plug; stainless steel cover including screws. E. Flashing Flanges: Cast-iron watertight stack or wall sleeve with membrane flashing ring. Provide underdeck clamp and sleeve length as required. F. Vent Flashing Sleeves: Cast-iron calking type roof coupling for cast-iron stacks, cast-iron threaded type roof coupling for steel stacks, and cast-bronze stack flashing sleeve for copper tubing. G. Manufacturer: Subject to compliance with requirements, provide drainage piping products of one of the 3. Smith (Jay R.) Co. 4. Tyler Pipe; Subs. of Tyler Corp. 5. Watts Drainage Products, Inc. 6. Zurn Industries Inc.; Hydromechanics Div FLOOR DRAINS CD Pricing/Permit; April 24,
5 A. General: Provide floor drains of size as indicated on drawings; and type, including features, as specified herein: B. FD-1: Coated cast iron floor drain, two piece body with double drainage flange, flashing collar, weepholes, bottom outlet inside caulk connection and adjustable 5 satin bronze round strainer with internal bronze backwater valve. Cast iron P-trap. Josam AJ Series or Wade W-1100-BV or equal. Exclude back water valve on floor drains serving above grade floor levels. C. FD-2: Same as floor drain FD-1 with 8 nickel bronze round strainer, sediment bucket. Exclude backwater valve at above grade floor drains. D. FD-3: Same as floor drain FD-1 with vandal resistant screws, W/O backwater valve. F. HD-1: Hopper Drain "H.D.": Stainless Steel floor drain with square body and removable hinged grate plus secondary strainer. Deep seal trap and backwater valve. Include hinged half grate where serving continuous flow equipment( verify with owner). Include perforated SS sediment Bucket. Wade W or equal. H. Manufacturer: Subject to compliance with requirements, provide floor drains of one of the 3. Smith (Jay R.) Mfg. Co. 4. Wade Div., Tyler Pipe 5. Zurn Industries, Inc., Hydromechanics Div. PART 3 - EXECUTION 3.01 INSPECTION A. Examine substrates and conditions under which soil and waste systems are to be installed. Do not proceed with work until unsatisfactory conditions have been corrected in manner acceptable to Installer INSTALLATION OF ABOVEGROUND PIPING A. General: Install soil and waste piping in accordance with Division-15 Basic Mechanical Materials and Methods section "Pipes and Pipe Fittings," and with State and Local Plumbing Codes INSTALLATION OF BUILDING DRAIN PIPING A. General: Install underground building drains as indicated and in accordance with State and Local Plumbing Codes. Lay underground building drains beginning at low point of systems, true to grades and alignment indicated with unbroken continuity of invert. Place bell ends of piping facing upstream. Install required gaskets in accordance with manufacturer's recommendations for use of lubricants, cements, and other special installation requirements. Clean interior of piping of dirt and other superfluous material as work progresses. Maintain swab or drag in line and pull past each joint as it is completed. Place plugs in ends of uncompleted piping at end of day or whenever work stops. B. Install soil and vent piping pitched to drain at minimum slope of 1/4" per foot (2%) for piping 3" and smaller, and 1/8" per foot (1%) for piping 4" and larger CD Pricing/Permit; April 24,
6 C. Install 2" thick extruded polystyrene over underground building drain piping not under building. Provide width to extend minimum of 18" beyond each side of pipe. Install directly over pipe, centered on pipe center line INSTALLATION OF PIPING SPECIALTIES A. Install piping specialties in accordance with Division-15 Basic Mechanical Materials and Methods section "Piping Specialties." B. Frost-Proof Vent Caps: Install frost-proof vent caps on each vent pipe passing through roof, and elsewhere where indicated. Maintain 1" clearance between vent pipe and roof substrate INSTALLATION OF SUPPORTS AND ANCHORS A. Install supports and anchors in accordance with Division-15 Basic Mechanical Materials and Methods section "Supports and Anchors." 3.06 INSTALLATION OF BACKWATER VALVES A. Install backwater valves in sanitary building drain piping as indicated, and as required by State and Local Plumbing Codes. For interior installation, provide cleanout cover flush to floor centered over backwater valve cover, and of adequate size to remove valve cover for service INSTALLATION OF EXPANSION JOINTS A. Install expansion joints on vertical risers as indicated, and as required by National Standard Plumbing Code INSTALLATION OF DRAINAGE PIPING PRODUCTS A. Cleanouts: Install in above ground piping and building drain piping as indicated, as required by State and Local Plumbing Codes; and at each change in direction of piping greater than 45 ; at minimum intervals of 50' for piping 4" and smaller and 100' for larger piping; and at base of each vertical soil or waste stack. Install floor and wall cleanout covers for concealed piping, select type to match adjacent building finish. B. Flashing Flanges: Install flashing flange and clamping device with each stack and cleanout passing through waterproof membranes. C. Vent Flashing Sleeves: Install on stacks passing through roof, secure over stack flashing in accordance with manufacturer's instructions INSTALLATION OF FLOOR DRAINS A. General: Install floor drains in accordance with manufacturer's written instructions and in locations indicated. B. Coordinate flashing work with work of waterproofing and adjoining substrate work. C. Coordinate with soil and waste piping as necessary to interface floor drains with drainage piping systems. D. Install floor drains at low points of surface areas to be drained, or as indicated. Set tops of drains flush with finished floor. E. Install drain flashing collar or flange so that no leakage occurs between drain and adjoining flooring. Maintain integrity of waterproof membranes, where penetrated CD Pricing/Permit; April 24,
7 F. Position drains so that they are accessible and easy to maintain INSTALLATION OF TRAP PRIMERS A. General: Install trap primers as indicated, and in accordance with manufacturer's installation instructions. Pitch piping towards drain trap, minimum of 1/8" per foot (1%). Adjust trap primer for proper flow EQUIPMENT CONNECTIONS A. Piping Runouts to Fixtures: Provide soil and waste piping runouts to plumbing fixtures and drains, with approved trap, of sizes indicated; but in no case smaller than required by the State and Local Plumbing Codes. B. Locate piping runouts as close as possible to bottom of floor slab supporting fixtures or drains FIELD QUALITY CONTROL A. Piping Tests: Test soil and waste piping system in accordance with requirements of the State and Local Plumbing Codes ADJUSTING AND CLEANING A. Clean, flush, and inspect soil and waste piping in accordance with requirements of Division-15 Basic Mechanical Materials and Methods section "Pipes and Pipe Fittings." 3.14 PROTECTION A. Protect drains during remainder of construction period, to avoid clogging with construction materials and debris, and to prevent damage from traffic and construction work. END OF SECTION CD Pricing/Permit; April 24,
SECTION 221413 FACILITY STORM DRAINAGE PIPING
SECTION 221413 FACILITY STORM DRAINAGE PIPING PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationAll work shall comply with applicable codes and ordinances. Work shall comply with the BOCA National Plumbing Code, latest edition.
DIVISION 15 MECHANICAL SECTION 15100 - PLUMBING PART 1 - GENERAL SCOPE Plumbing work includes all domestic water, gas, and sanitary sewer systems as shown on plans. Also all fixtures and equipment which
More informationA. This Section includes the following for soil, waste, and vent piping inside the building:
June 2014, Draft 01 22 1316 Sanitary and Waste Vent Piping PART 1. GENERAL 1.01 Summary A. This Section includes the following for soil, waste, and vent piping inside the building: 1. Pipe, tube, and fittings.
More informationSECTION LS 2530 SANITARY SEWERS. A. General: Submit the following in accordance with The General Conditions.
SECTION LS 2530 SANITARY SEWERS PART 1 GENERAL 1.1 SUBMITTALS A. General: Submit the following in accordance with The General Conditions. 1. Product data for drainage piping specialties. 2. Shop drawings
More informationCLEANOUT FEATURES. KLEENATRON II Features CLEANOUTS
CLEANOUT FEATURES KLEENATRON II Features JOSAM KLEENATRON II Cleanouts incorporate features developed to meet the latest in building construction methods. These features ensure the specifier, installer
More informationDENVER PUBLIC SCHOOLS DESIGN AND CONSTRUCTION STANDARDS This Standard is for guidance only. SECTION 15430 PLUMBING SPECIALTIES
PART 0 DESIGN STANDARDS 0.01 GENERAL DESIGN GUIDELINES A. Roof drains 1. Coordinate location and depth of drains to assure adequate pitch of the drainage area to drain. 2. Overflow system shall be piped
More informationSECTION 02630 STORM DRAINAGE SYSTEM
SECTION 02630 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for storm drainage systems including modifications and connections to existing storm drainage systems. 1.02 REFERENCE
More informationFLOOR AND AREA DRAINS
Pictorial Index Product Recommendations Floor Drain Selection Factors Load Rating Grate Free Area Material & Characteristics Pipe Connection Commonly Specified Options Typical Installations FLOOR AND AREA
More informationROOF DRAINS TABLE OF CONTENTS
Pictorial Index Product Recommendations Roof Drain Selection Factors Sizing Placement Material & Characteristics Pipe Connection Commonly Specified Options Typical Installations TABLE OF CONTENTS ROOF
More informationLS 2540 SEWER LATERALS AND INSPECTION TEES
LS 2540 SEWER LATERALS AND INSPECTION TEES A. Summary B. Submittals C. Site Information D. Sewer Pipe and Fittings E. Lateral Locations F. Lateral Installation G. Inspection Tee Installation H. Removal
More informationCHAPTER 11 STORM DRAINAGE
CHAPTER 11 STORM DRAINAGE SECTION 11 GENERAL 11.1 Scope. The provisions of this chapter shall govern the materials, design, construction and installation of storm drainage. 11.2 Where required. All roofs,
More informationTop 10+ Mistakes of DWV plumbing design
Top 10+ Mistakes of DWV plumbing design Listed below are the some of the most frequently missed items, noticed by our inspectors, at plumbing rough-in when non-plumbers attempt plumbing design. Most of
More informationA. Section includes the following soil and waste, sanitary drainage and vent piping inside the building and to a point 5 feet outside the building:
SECTION 221316 - PART 1 - GENERAL 1.1 SUMMARY A. Section includes the following soil and waste, sanitary drainage and vent piping inside the building and to a point 5 feet outside the building: 1. Pipe,
More informationGRATES AND DRAINS HOUSTON ORLANDO GREENVILLE 800/392-5066 800/327-3022 800/476-2212 TOTAL MAINTENANCE SOLUTIONS
15-1 CLEANOUT COVERS 47471082 4-11/16 Josam, 3 screw 47471084 6-5/16 Josam, 3 screw 47761070 5-7/16 Smith, 3 screw w/ closure plug 47941108 6-1/4 Wade, 3 screw 47991400 4-5/8 Zurn, 3 screw 47991402 6-1/8
More information2006 Codes. Please verify the following before calling for inspection
INSPECTION CHECKLIST RESIDENTIAL PLUMBING ROUGH IN 2006 Codes This checklist is intended for use to prepare for an inspection. This is only a general list and is not intended to address all possible conditions.
More informationSECTION 22 42 00 COMMERCIAL PLUMBING FIXTURES
SECTION 22 42 00 COMMERCIAL PLUMBING FIXTURES PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationEFFECTIVE FEBRUARY 2014. note: drainage permit required to call for a dampproof inspection
EFFECTIVE FEBRUARY 2014 note: drainage permit required to call for a dampproof inspection 1. ROOF DRAINS/DECK DRAINS (INTERIOR ) All roof and deck drains within the perimeter of the building shall be APPROVED
More informationSECTION 23 05 29 - HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT
SECTION 23 05 29 - HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Pipe hangers and supports. 2. Hanger rods. 3. Inserts. 4. Flashing. 5. Equipment
More informationCHAPTER 11 STORM DRAINAGE
CHAPTER STORM DRAINAGE SECTION PC 0 GENERAL 0. Scope. The provisions of this chapter shall govern the materials, design, construction and installation of storm drainage. Storm water discharge shall be
More informationSECTION 02700 SEWERAGE AND DRAINAGE PART 1 - GENERAL 1.01 RELATED DOCUMENTS
SECTION 02700 SEWERAGE AND DRAINAGE PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including the General and Supplementary Conditions and Division 1 Specification
More informationJay R. Smith Mfg. Co.
Jay R. Smith Mfg. Co. Automatic Backwater Valve SMITH CUSTOMER DRIVEN FLOOD-GATE FEATURES Index Page Flood-Gate Features and Applications 2 How Flood-Gate Works 3 Flood-Gate Operation & Approvals 4 Valve
More informationPLUMBING ROUGH IN INSPECTION
This Program is made Possible through the Code Officials Education & Training Fund. Revenue for the Fund comes from Assessments on Building Permits. Please turn down cell phones and put pagers on vibrate.
More informationWhen Should Examination Preparation Begin?
Texas State Board of Plumbing Examiners Tradesman Plumber-Limited Licensee Examination Review Course The following Examination Review Course is designed to assist a registered Plumber s Apprentice in preparing
More informationAIR RELEASE, CLEANOUT, AND SEWER MANHOLES
AIR RELEASE, CLEANOUT, AND SEWER MANHOLES **From Hartford IM BLDG(10) DESCRIPTION. This work shall consist of the construction of air release, cleanout, and sanitary sewer manholes; and the furnishing
More informationCONSTRUCTION CHECKLIST Residential Plumbing Rough-In September 2004
Bellevue Bothell Kenmore Kirkland Issaquah Mercer Island Sammamish Snoqualmie Woodinville CONSTRUCTION CHECKLIST Residential Plumbing Rough-In September 2004 This checklist is intended for use to prepare
More informationINSPECTION CHECKLIST Residential Plumbing Rough In April 2011 Mercer Island Mill Creek Sammamish Snohomish County Snoqualmie Woodinville
Bellevue Bothell Burien Issaquah Kenmore Kirkland INSPECTION CHECKLIST Residential Plumbing Rough In April 2011 Mercer Island Mill Creek Sammamish Snohomish County Snoqualmie Woodinville 2009 Codes This
More informationSERVICE LINE EXTENSION AND SERVICE LINE CONNECTION CONDENSED SANITARY SEWER SYSTEM INSTALLATION SPECIFICATIONS
1001 SOUTH LEECHBURG HILL LEECHBURG, PA 15656 Phone: 724-845-9355 Fax: 724-845-1186 SERVICE LINE EXTENSION AND SERVICE LINE CONNECTION CONDENSED SANITARY SEWER SYSTEM INSTALLATION SPECIFICATIONS 1. General
More informationINTERCEPTORS TABLE OF CONTENTS S-WD-INTER-1 0812
TABLE OF CONTENTS Pictorial Index Product Recommendations Grease Interceptors Commonly Specified Options Typical Installations Oil Interceptors Commonly Specified Options Typical Installations Sediment
More informationPlumbing. Helpful Hints Residential Construction. Lincoln County. Bert Polk Plumbing Inspector
Plumbing Helpful Hints Residential Construction Bert Polk Plumbing Inspector Lincoln County 2015 Waste and vent fittings Vent 90 medium 90 long 90 1/16 bend,1/8 bend,1/6 bend, medium 90 san tee combination
More informationFLOOR DRAINS FLOOR DRAINS. SUPER-FLO Features
SUPER-FLO Features The two-piece Floor Drain bodies which are designed to be combined with any adjustable strainers offered by JOSAM have proven features which make them the easiest and quickest drains
More informationFIX TURE CARRI ERS. 140(a) MPB-2011-USA
FIXTURE CARRIERS STRUCTURAL FEET The feet are heavy duty cast ductile iron and invertible. No distinction is necessary between right and left hand. Each foot wraps around the specially formed edge of the
More informationCHAPTER 7 SANITARY DRAINAGE
701 GENERAL 701.1 Scope The provisions of this chapter shall govern the materials, design, construction, and installation of sanitary drainage systems. 701.6 Frost Protection No soil or waste pipe shall
More informationPlumbing Installations. A homeowner guide to the City of Winnipeg plumbing requirements for a single-family dwelling
Plumbing Installations A homeowner guide to the City of Winnipeg plumbing requirements for a single-family dwelling February 2001 contents General Information 3 Inspection 4 New Drain and Vent Installations
More informationCHAPTER 9 VENTS. copper drainage tube Type DWV, Schedule 40 plastic piping, or borosilicate glass.
CHAPTER 9 VENTS 901 GENERAL 901.1 Scope The provisions of this chapter shall govern the materials, design, construction, and installation of vents. 901.2 Protection of Trap Seals The protection of trap
More informationShower and Floor Gullies Channel Drain and Tile Drain SECTION
Shower and Floor Gullies Channel Drain and Tile Drain SECTION 2 Shower and Floor Gullies, Channel Drain and Tile Drain 29 General Information Shower and Floor Gullies McAlpine has responded to market conditions
More informationCHAPTER 11 STORM DRAINAGE
CHAPTER 11 STORM DRAINAGE 1101.0 General. 1101.1 Where Required. Roofs, paved areas, yards, courts, courtyards, vent shafts, light wells, or similar areas having rainwater, shall be drained into a separate
More informationPlumbing Installations A homeowner guide to the City of Winnipeg plumbing requirements for a single-family dwelling
PLANNING, PROPERTY AND DEVELOPMENT DEPARTMENT Plumbing Installations A homeowner guide to the City of Winnipeg plumbing requirements for a single-family dwelling October 2014 contents General Information
More informationPIPES AND TUBES FOR HVAC PIPING AND EQUIPMENT
PIPES AND TUBES FOR HVAC PIPING AND EQUIPMENT GENERAL INFORMATION 1.1 This section applies to piping systems for chilled water, hot water, condenser water, steam, condensate return, fuel oil, refrigerant
More informationSIERRA LAKES COUNTY WATER DISTRICT P.O. Box 1039, Soda Springs, CA 95728-1039 (7300 Short Road, Serene Lakes)
SIERRA LAKES COUNTY WATER DISTRICT P.O. Box 1039, Soda Springs, CA 95728-1039 (7300 Short Road, Serene Lakes) Maintenance Office Administrative Office Billing Office 530-426-7802 530-426-7800 916-332-4872
More informationSECTION 02150 REMOVAL OR ABANDONMENT OF EXISTING UTILITIES AND UNDERGROUND STRUCTURES. 1. Trench excavation, backfill, and compaction; Section 02250.
02150-1 of 6 SECTION 02150 REMOVAL OR ABANDONMENT OF EXISTING 02150.01 GENERAL A. Description Removal or abandonment of existing utilities and underground structures shall include, but not necessarily
More informationNote: All dimensions are nominal. All weights are for shipping purposes only. Availability is subject to change.
CHANNEL DrAiNS Durable Designed for maximum durability and drainage, NDS Channel Drains are a proven alternative to traditional concrete drains. UV inhibitors in the grates, channel and component parts
More informationWastewater Capital Projects Management Standard Construction Specification
CITY AND COUNTY OF DENVER ENGINEERING DIVISION Wastewater Capital Projects Management Standard Construction Specification 10.1 Precast Concrete Pipe 10.1.1 General This section covers material requirements,
More informationARTICLE II (2) ARTICLE II - REQUIRED USE OF PUBLIC SEWERS. PARAGRAPH 020001 Purpose and Application.
ARTICLE II - REQUIRED USE OF PUBLIC SEWERS. PARAGRAPH 020001 Purpose and Application. Article II provides rules governing the allowable connection to the City POTW and the construction and inspection of
More informationTown House 11265 Center Highway North Huntingdon, PA 15642
APPENDIX C SPECIFICATIONS FOR THE CONSTRUCTION OF BUILDING LATERAL SANITARY SEWERS DECEMBER 2004, INCLUDING AMENDMENTS ADOPTED ON FEBRUARY 6, 2008 AND APRIL 2, 2008; EFFECTIVE ON MAY 1, 2008 Town House
More informationSECTION 16402 UNDERGROUND ELECTRIC SERVICE
SECTION 16402 UNDERGROUND ELECTRIC SERVICE PART 1 GENERAL 1.1 SUMMARY A. Description of System 1. Furnish all labor, materials, and equipment for below grade work external to buildings as required, and
More informationCHAPTER 10 TRAPS, CLEAN-OUTS, AND INTERCEPTORS
PlumbingCode06_ch10 5/29/06 8:16 AM Page 1 CHAPTER 10 TRAPS, CLEAN-OUTS, AND INTERCEPTORS We have covered most of the regulations you will need to know about drains and vents. This chapter will round out
More information32-02.05 Precast Manhole Sections and Castings. These items shall conform to Section 31, "Storm Drain Installation," of these Standard Provisions.
SECTION 32: SANITARY SEWER INSTALLATION 32-01 SCOPE. The Work shall consist of furnishing and installing sewer mains, manholes, laterals, cleanout fittings and appurtenances; and testing, flushing and
More informationResidential Plumbing BCN 1058
Residential Plumbing BCN 1058 CHAPTER 7 Plumbing Fixtures and Sizing the Drain, Waste, and Vent System MICHAEL KNOTEK 74 Plumbing Fixtures and Sizing the Drain, Waste, and Vent System PLUMBING FIXTURES
More informationSANITARY SEWER SPECIFICATIONS
SANITARY SEWER SPECIFICATIONS OCTOBER 2003 HARVEST-MONROVIA WATER, SEWER, AND FIRE PROTECTION AUTHORITY SECTION 1.00 1.10 Purpose The purpose of this document is to assemble the sewer specifications, policies,
More informationroline Commercial Drainage Products Catalog & Price List Effective April 2, 2012 watts.com
roline Commercial Drainage Products Catalog & Price List Effective April 2, 2012 watts.com Index Floor Drains FD4 Snap-In Stainless Steel Grate............3 FD5 General Purpose Floor Drain.............3
More informationSEPTIC SYSTEM CONSTRUCTION REQUIREMENTS ST. MARY S COUNTY HEALTH DEPARTMENT
SEPTIC SYSTEM CONSTRUCTION REQUIREMENTS ST. MARY S COUNTY HEALTH DEPARTMENT The following are minimum requirements for installation of conventional trench sewage disposal systems in St. Mary s County,
More informationSECTION 15140 - PIPE HANGERS AND SUPPORTS
Part I - GENERAL 1.01 SECTION INCLUDES A. The work covered under this section consists of the furnishing of all necessary labor, supervision, materials, equipment, and services to completely execute the
More informationCODE GUIDE 302 and Glossary of Industry Terms
CODE GUIDE 302 and Glossary of Industry Terms A Guide for Code Authorities and Others for Selected - % Plumbing and Drainage Products Issued By THE PLUMBING AND DRAINAGE INSTITUTE 800 Turnpike Street ~
More informationEXHIBIT "A. Technical Specifications for Water and Sewer Service Lines
EXHIBIT "A Technical Specifications for Water and Sewer Service Lines Water and Sewer Line Bedding and Backfill: Drawings show cross-section of trench, pipe laid on top of 6" min. bedding material, bedding
More information112039.00 224500 EMERGENCY PLUMBING FIXTURES
PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following emergency plumbing fixtures: 1. Emergency showers. 2. Eyewash equipment. 3. Eye/face wash equipment. 4. Hand-held drench hoses. 5. Combination
More informationExcerpts from the Canadian National Building Code (NBC)
Excerpts from the Canadian National Building Code (NBC) Reproduced here with Permission of the Copyright Owner, the National Research Council of Canada, Institute for Research in Construction. For more
More informationA. Accessible Fixture: Emergency plumbing fixture that can be approached, entered, and used by people with disabilities.
SECTION 224500 - EMERGENCY PLUMBING FIXTURES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationDARTMOUTH COLLEGE DESIGN January 3, 2012 & CONSTRUCTION GUIDELINES
SECTION 15062 STEAM AND CONDENSATE PIPING PART 1 DESIGN DIRECTIVES 1.1 QUALITY ASSURANCE A. Comply with the provisions of the following: 1.2 DESIGN CRITERIA 1. ASME B 31.9 Building Services Piping : for
More informationFIRING RANGE PHASE 1 DESIGN 224500-1
FIRING RANGE PHASE 1 DESIGN 224500-1 SECTION 224500 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationA. Contractor shall furnish, to the Engineer, all materials certifications available from the manufacturer for all required materials.
PART 1 GENERAL 1.1 SCOPE A. This item shall include the work necessary for the installation of storm sewer line construction. B. Reference Section 3800 Trenching and Backfill and the General Conditions,
More informationSewage Compliance Form Instructions
CITY OF JOHNSTOWN DEPARTMENT OF COMMUNITY & ECONOMIC DEVELOPMENT 401 MAIN STREET ROOM 200 JOHNSTOWN, PA 15901 814-533-2017 FAX 814-539-5816 RENEE K. DALY DIRECTOR Sewage Compliance Form Instructions 1)
More informationSubpart 1. Installation. All plumbing systems must be. installed and tested according to this chapter and chapter 4715,
4658.4500 PLUMBING SYSTEMS; NEW CONSTRUCTION. Subpart 1. Installation. All plumbing systems must be installed and tested according to this chapter and chapter 4715, the Minnesota Plumbing Code. Subp. 2.
More informationSECTION 02763 POINT REPAIRS TO SANITARY SEWERS. A. Repairs to existing sewer lines by replacing short lengths of failed pipe.
SECTION 02763 PART 1 G E N E R A L 1.01 SECTION INCLUDES A. Repairs to existing sewer lines by replacing short lengths of failed pipe. 1.02 UNIT PRICES A. Measurement for point repairs is on a unit price
More information2010 Residential Water Heater Replacement Check List
2010 Residential Water Heater Replacement Check List The intent of this check list is to provide installers a general reference for the enforcement of code requirements in the Greater San Diego Area. This
More informationSECTION 33 05 16.13 PRECAST CONCRETE UTILITY STRUCTURES
SECTION 33 05 16.13 PRECAST CONCRETE PART 1 - GENERAL 1.01 SECTION INCLUDES A. This item shall consist of the construction of both sanitary and storm sewer precast concrete manholes in accordance with
More informationDIVISION 2 - SEWERAGE AND DRAINAGE SECTION 02720 - STORM DRAIN SYSTEMS PART 1 - GENERAL
DIVISION 2 - SEWERAGE AND DRAINAGE SECTION 02720 - STORM DRAIN SYSTEMS PART 1 - GENERAL 1.01 DESCRIPTION A. Furnish and install all storm drains, including manholes, inlets, service lines and other appurtenant
More informationArapahoe County Residential Water Heater Installation and Inspection Guide
Arapahoe County Residential Water Heater Installation and Inspection Guide The attached handout is designed to be a general permit submittal and inspection guide covering most installation instances, however
More informationSECTION 33 41 13 PUBLIC STORM UTILITY DRAINAGE PIPING
SECTION 33 41 13 PUBLIC STORM PART 1 - GENERAL 1.01 SECTION INCLUDES A. Storm drainage piping, fittings, and accessories at proposed station areas and locations other than under and immediately adjacent
More informationFOUNDATION INSULATING SYSTEM, INCLUDING WATERPROOFING AND DAMP PROOFING
FOUNDATION INSULATING SYSTEM, INCLUDING WATERPROOFING AND DAMP PROOFING insulation installed on foundation walls must be separated from the building interior with a code approved thermal barrier. Foam
More informationPlugging Home Drains to Prevent Sewage Backup
AE-1476 Plugging Home Drains to Prevent Sewage Backup Why plug drains For homes in areas of the country prone to flooding or heavy rain, taking a few steps to prepare for water levels that could result
More informationOne Year Warranty. Stock U.S. # of Volts Weight CONN. Height Dia. Watts # GAL. Elements INS. Inches NATURAL GAS* Six Year Warranty
One Year Warranty ELECTRIC Stock U.S. # of Volts Weight CONN. Height Dia. Watts # GAL. Elements INS. Inches Fused Ceramic Shield tank lining is corrosion-resistant for years of dependability. Adjustable
More informationHow To Make A House Safe
1 RESIDENTIAL Screen Enclosures Orange County Residential Code Compliance Alternative design method for screen enclosures R301.2.1.1.3 PLAN REVIEW Engineered plans must state that the Alternative Design
More information5.23.22 STEAM AND CONDENSATE PIPING AND PUMPS DESIGN AND CONSTRUCTION STANDARD PART 1: GENERAL. 1.01 Purpose:
PART 1: GENERAL 1.01 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is
More informationSECTION 6 SANITARY SEWER MAIN 6.01 SCOPE
6.01 SCOPE The work covered by this section of the specifications consists of the furnishing of all plant, labor, materials, equipment and supervision and performing all operations involved in the construction
More information8.7 Schluter -KERDI-LINE
8.7 Schluter -KERDI-LINE INNOVATIVE SOLUTIONS FOR CERAMIC AND STONE TILE LINEAR DRAINS FOR BONDED WATERPROOFING ASSEMBLIES Application and Function 8.7 Schluter -KERDI-LINE is a low profile linear floor
More informationSECTION 02530 STORM DRAINAGE STRUCTURES. 1. Trench excavation, backfill, and compaction; Section 02250.
02530-1 of 5 SECTION 02530 STORM DRAINAGE STRUCTURES 02530.01 GENERAL A. Description Storm drainage structure construction shall include, but not necessarily be limited to, furnishing and installing or
More informationSAMPLE TEST QUESTIONS STEAMFITTER/PIPEFITTER - ITA WEBSITE
1 Which tool is used to correct internal hi-low when preparing a 4-in. steel pipe for welding? A. 4-in. grinder with cutting disc. B. Mini-grinder with flapper disc. C. Pencil grinder with cone stone.
More informationWhy Do I Have Sewer Smells In My Home or Business?
Why Do I Have Sewer Smells In My Home or Business? Before we discuss why you may be getting smells through your drain pipes, lets first take a look at how your plumbing is supposed to work. Properly constructed
More informationSECTION 11014 WINDOW WASHING SYSTEMS
SECTION 11014 WINDOW WASHING SYSTEMS PART 1 - GENERAL 1.1 SUMMARY A. Section includes, but is not limited to, design and furnishing portable davits, davit sleeves, dvit bases, four (4) removable outriggers,
More informationCITY OF SELMA, TEXAS Inspection Checklist: Commercial
Rev Y71004 The Permits and Inspections Department welcomes you to the City of Selma. The following information is provided to you as guidance through the inspection process. The City of Selma provides
More informationThis handout is a guide only and does not contain all of the requirements of the Minnesota State Building Code or city ordinances.
Basement Finishing Guide Community Development Department Building Inspections Division 5200 85 th Avenue North / Brooklyn Park, MN 55443 Phone: (763) 488-6379 / Fax: (763) 493-8171 6/15 www.brooklynpark.org
More informationSECTION 33 31 00.11 GRAVITY SANITARY SEWERS
SECTION 33 31 00.11 GRAVITY SANITARY SEWERS PART 1: GENERAL 1.01 SCOPE A. Gravity sanitary sewers and appurtenances. 1.02 SUBMITTALS A. Conform to requirements of Section 01 33 00 Submittals. B. Submit
More information- 3 - SANITARY SEWER BACK-UP
WHY IS THERE WATER IN MY BASEMENT? There are two major sources of water in a basement as the result of a heavy rainfall. 1. Sanitary Sewer Back-up 2. Storm Water Infiltration In order to safe guard your
More informationDIVISION 22 PLUMBING. 22 30 00 PLUMBING EQUIPMENT 22 33 00 Domestic Water Heaters
DIVISION 22 PLUMBING 22 00 00 PLUMBING 22 00 50 Design Criteria 22 01 00 General Requirements 22 05 00 Common Work Results 22 06 00 General Duty Valves 22 07 00 Insulation 22 08 00 Commissioning 22 10
More informationCONSOLIDATED EDISON CO. OF NEW YORK, INC. 4 IRVING PLACE NEW YORK, NY 10003 DISTRIBUTION ENGINEERING DEPARTMENT SUBSTATION & EQUIPMENT SECTION
CONSOLIDATED EDISON CO. OF NEW YORK, INC. 4 IRVING PLACE NEW YORK, NY 10003 DISTRIBUTION ENGINEERING DEPARTMENT SUBSTATION & EQUIPMENT SECTION SPECIFICATION EO-5023 REVISION 3 MARCH 2003 REQUIREMENTS FOR
More informationSEWER BACKUPS & BASEMENT FLOODING PREVENTATIVE SOLUTIONS FOR THE BUILDING OWNER
Village of Shorewood, Wisconsin SEWER BACKUPS & BASEMENT FLOODING PREVENTATIVE SOLUTIONS FOR THE BUILDING OWNER Prepared By: Thomas A. Zoulek, P.E., LEED A.P. Vice President Mid City Plumbing & Heating
More informationONE AND TWO FAMILY DWELLINGS Plumbing July, 2007
ONE AND TWO FAMILY DWELLINGS Plumbing July, 2007 The following are general requirements pertaining to plumbing in one and two family dwellings. This does not represent all the provisions regulating plumbing
More information08003-1 WATER SERVICE 2
08003_Mar08_2011.pdf Page 1 of 7 INDEX Page 08003-1 WATER SERVICE 2 1.1 Pipe 2 1.1.1 Copper 2 1.1.2 Polyethylene 2 1.2 Valves and Fittings 2 1.2.1 Main Stops 3 1.2.2 Curb Stops 3 1.2.3 Curb Box 3 1.2.4
More informationInstallation Instructions 4508 4508S
SYMPHONY Spread Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Speed Connect
More informationChapter 7 Plumbing Connections
Chapter 7 Plumbing Connections 7-1 General All plumbing equipment and installations must be designed, constructed, and installed in accordance with this code and where not specific, to the applicable provisions
More informationWhat to Expect From the Examination. How to Study the Plumbing Codes
Texas State Board of Plumbing Examiners Plumbing Inspector Examination Review Course The following Examination Review Course is designed to assist an applicant in preparing for the Plumbing Inspector examination.
More informationUniversal Installation and Maintenance Instructions Double Wall Spill Containment Bucket (5 and 15 gal)
Universal Installation and Maintenance Instructions Double Wall Spill Containment Bucket (5 and 15 gal) IMPORTANT: It is imperative that the user read these warnings and use of the assembly instructions
More informationA. Submit data on all materials, fittings, accessories and equipment.
SECTION 22 14 00 - FACILITY STORM DRAINAGE PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Storm water piping buried beyond 5 feet of building. 2. Storm water piping buried within 5 feet of building.
More informationPVC Pipe Restriction Law and Legislation 1) NYS PVC Pipe Restriction Law (Repealed)
PVC Pipe Restriction Law and Legislation 1) NYS PVC Pipe Restriction Law (Repealed) * 246. Uses of standard piping materials. 1. Building sewers under public ways. Building sewers under public ways shall
More informationFabricated Drainage Products
Fabricated Drainage Products Complete Drainage System Inline Drains are used At the beginning of a drain line Add a new water inlet to an existing drain line using a riser pipe and tee HARCO Surface Drainage
More informationElement D Services Plumbing
PART 1 - GENERAL 1.01 OVERVIEW A. This section addresses domestic cold, hot and hot water return distribution systems within and to five feet beyond building perimeter. PART 2 - DESIGN CRITERIA 2.01 GENERAL
More informationPackaged Terminal Air Conditioner Wall Sleeve Installation
Installation & Maintenance Data IM 1196 Group: PTAC Part Number: 910141799 Date: October 2013 Packaged Terminal Air Conditioner Installation x 42" PGAN with Top-Mounted Hydronic Heat Note: Installation
More informationResidential Deck Safety, Construction, and Repair
Juneau Permit Center, 4 th Floor Marine View Center, (907)586-0770 This handout is designed to help you build your deck to comply with the 2006 International Residential Building code as modified by the
More informationSuperform Products Ltd.
TYPICAL CORNER REINFORCING NOTE : SEE ENGINEERED REBAR SCHEDULES SUPPLIED BY THE MANUFACTURER STEEL REINFORCEMENT WALL CORNER 90 Copyright 2012 Sept. 2012 5.1.1 Rebar Spacing 6" 12" Max. Load LB./FT. 2000
More informationMitigating Basement Backups
Mitigating Basement Backups Avon Lake Municipal Utilities 201 Miller Road Avon Lake, OH 44012 Tel: 440-933-6226 Emergency: 440-933-3229 www.avonlakewater.org April 28, 2011 This document was originally
More information