AAMA/WDMA/CSA 101/I.S.2/A Standard/Specification for windows, doors, and unit skylights EXCERPT EDITION
|
|
|
- Bernard Griffin
- 9 years ago
- Views:
Transcription
1 AAMA/WDMA/CSA 101/I.S.2/A Standard/Specification for windows, doors, and unit skylights EXCERPT EDITION Product Designations (Product Types, Performance Classes & Grades), and Gateway Performance Requirements CMB-5-05
2
3 4 General Requirements 4.1 General - This voluntary Standard/Specification covers requirements for single and dual windows, single and dual side-hinged door systems, sliding doors, and unit skylights for new construction and replacement applications. All products rated in accordance with this Standard/Specification shall conform to all the requirements of this Standard/Specification. All products covered by this Standard/Specification shall be installed in full accordance with the manufacturer s instructions. 4.2 Markings/Identifications - When required by local code or project specification, windows, doors, and unit skylights shall include a permanent identification of the product manufacturer. 4.3 Gateway Performance Requirements - Each product type has a defined gateway set of primary requirements for the applicable product type before entry into the performance class is permitted (see Table 1). Gateway performance requirements are the minimum allowable performance levels that a gateway test specimen shall achieve in order for a product to be rated with a particular classification (R, LC, C, HC, or AW). The gateway test specimen size shall be equal to or larger than the specified gateway size, in both height and width. Typically, the minimum allowable performance levels and the gateway size change as the classification changes. All gateway test specimens shall achieve certain minimum performance levels for air leakage resistance, water penetration resistance, uniform load, and, where required, forced-entry resistance and operating force. Also, all gateway test specimens shall achieve certain additional minimum performance levels for auxiliary (durability) and material tests specific to the product operator type. See Clause 5 for additional details. Product Performance Class Minimum Performance Grade Minimum Design Pressure, Pa (psf) Minimum Structural Test Pressure, Pa (psf) Minimum Water Resistance Test Pressure, Pa (psf) Windows and doors R (15.0) 1080 (22.5) 140 (2.90) LC (25.0) 1800 (37.5) 180 (3.75) C (30.0) 2160 (45.0) 220 (4.50) HC (40.0) 2880 (60.0) 290 (6.00) AW (40.0) 2880 (60.0) 390 (8.00) Unit skylights and roof windows R (15.0) 1440 (30.0) 140 (2.90) C (30.0) 2880 (60.0) 220 (4.50) HC (40.0) 3840 (80.0) 290 (6.00) TABLE 1 GATEWAY REQUIREMENTS 4.4 Product Designations General - A primary designator shall be used to designate products included in this Standard/Specification. An optional secondary designator shall be permitted to be used if desired Primary Designator General - The primary designator in this Standard/Specification is a four-part code, which includes product type, performance class, performance grade (design pressure), and maximum size tested to achieve this rating. For reporting purposes, the product type shall be typed in full or represented by abbreviations as shown in Figures 2 to 4. Abbreviations shall be as per Table 2. An asterisk (*) added to the size designation indicates that the size tested was an additional test unit that was smaller than the gateway test size for the original product type and performance class, for the purpose of meeting optional performance grade (design pressure) requirements. An example is shown in Figure 3. See Clause for further details regarding optional performance grades (design pressures). Hung Window R x 1800* (32 x 71*) H R x 1800* (32 x 71*) or or Hung Window RM x 1800* H RM x 1800* Legend: Hung Window or H - product type (see Clause ) R - performance class (inch-pound) (see Clauses and ) RM - performance class (SI) (see Clauses and ) 30 - performance grade (design pressure) (inch-pound) (see Clauses 0.2.3, , and ) performance grade (design pressure) (SI) (see Clauses , , and ) 800 x maximum size tested (SI) (see Clause ) (32 x 71) - maximum size tested (inch-pound) (optional) (see Clause )
4 * - downsized test specimen FIGURE 3 PRIMARY DESIGNATOR (EXAMPLE 2) The characters LW shown in the product type in Figure 4 indicate limited water penetration resistance. LW ratings shall only be permitted for side-hinged door systems, and shall not be permitted for any other product types. Also, LW ratings shall only be permitted where the representative test specimen has successfully passed a water penetration resistance test at a pressure differential of 0 Pa (0.0 psf) or higher, but less than the minimum test pressure required for the indicated performance class and performance grade (design pressure). If the test specimen is not successfully tested to a water penetration resistance test pressure equal to or greater than 0 Pa (0.0 psf), then that side-hinged door system shall not be considered in compliance with this Standard/Specification. An example is shown in Figure 4. Limited Water Side-Hinged Door R x 2000 (36 x 79) LW SHD R x 2000 (36 x 79) or or Limited Water Side-Hinged Door RM x 2000 LW SHD RM x 2000 Legend: LW - limited water Side-Hinged Door or SHD - product type (see Clause ) R - performance class (inch-pound) (see Clauses and ) RM - performance class (SI) (see Clauses and ) 40 - performance grade (design pressure) (inch-pound) (see Clauses 0.2.3, , and ) performance grade (design pressure) (SI) (see Clauses 0.2.3, , and ) 900 x maximum size tested (SI) (see Clause ) (36 x 79) - maximum size tested (inch-pound) (optional) (see Clause ) FIGURE 4 PRIMARY DESIGNATOR (EXAMPLE 3) Products that have been tested as dual windows as specified in Clause 4.5 shall have the code DW added to their product designation after the product type. An example of a product designation for a dual window would be HS DW LC Products that have been tested as dual doors as specified in Clause 4.5 shall have the code DD added to their product designation after the product type. An example of a product designation for a dual door would be SHD DD LC Product Type - When used, product designations shall be as per Table 2 for the window, door, and unit skylight product types covered in this Standard/Specification. The depictions in Figure 5 are general in nature and are not all-inclusive. AP = Awning, hopper, projected window LW DASHD = Limited water dual-action side-hinged door ATD = Architectural terrace door LW SHD = Limited water side-hinged door BW = Basement window RW = Roof window C = Casement window SD = Sliding door DASHD = Dual-action side-hinged door SHD = Side-hinged door DAW = Dual-action window SHW = Side-hinged (inswinging) window FD = Fixed door SKG = Unit skylight glass glazed FW = Fixed window SKP = Unit skylight plastic glazed GH = Greenhouse window SLT = Side lite H = Hung window SP = Specialty product HE = Hinged rescue window TA = Tropical awning window HP = Horizontally pivoted window TH = Top-hinged window HS = Horizontal sliding window TR = Transom J = Jalousie window VP = Vertically pivoted window JA = Jal-awning window VS = Vertical sliding window TABLE 2 PRODUCT TYPES Performance Class Products included in this Standard/Specification shall be classified according to any of the five performance classes (R, LC, C, HC, and AW) as described in Clause and Table 1.
5 Product Type Architectural terrace door Awning, hopper, projected window Product Designation TABLE 25 GATEWAY PERFORMANCE REQUIREMENTS Minimum Test Size, mm (in) Minimum Design Pressure, Pa (lbf/ft 2 ) Deflection at Design Pressure, mm (in) Minimum Structural Pressure, Pa (lbf/ft 2 ) Minimum Water Air Leakage Resistance Pressure, Pa (lbf/ft 2 ) Pa (lbf/ft 2 ) L/s m 2 (cfm/ft 2 ) ATD-HC (42 90) 1920 (40.0) L/ (60.0) 290 (6.0) 300 (6.2) 1.5 (0.3) ATD-AW (48 96) 1920 (40.0) L/ (60.0) 390 (8.0) 300 (6.2) 0.5 (0.1) AP-R (48 16) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) AP-LC (48 32) 1200 (25.0) Reported 1800 (37.5) 180 (3.8) 75 (1.6) 1.5 (0.3) AP-C (48 32) 1440 (30.0) Reported 2160 (45.0) 220 (4.5) 75 (1.6) 1.5 (0.3) AP-HC (60 32) 1920 (40.0) L/ (60.0) 290 (6.0) 300 (6.2) 1.5 (0.3) AP-AW (60 36) 1920 (40.0) L/ (60.0) 390 (8.0) 300 (6.2) 0.5 (0.1) Basement window BW-R (32 14) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) Casement window Dual-action side- hinged door Dual-action window Fixed door Fixed window C-R (24 60) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) C-LC (32 60) 1200 (25.0) Reported 1800 (37.5) 180 (3.8) 75 (1.6) 1.5 (0.3) C-C (32 60) 1440 (30.0) Reported 2160 (45.0) 220 (4.5) 75 (1.6) 1.5 (0.3) C-HC (36 60) 1920 (40.0) L/ (60.0) 290 (6.0) 300 (6.2) 1.5 (0.3) C-AW (36 60) 1920 (40.0) L/ (60.0) 390 (8.0) 300 (6.2) 0.5 (0.1) DASHD-R (36 79) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) DASHD-LC (36 83) 1200 (25.0) Reported 1800 (37.5) 180 (3.8) 75 (1.6) 1.5 (0.3) DASHD-C (40 83) 1440 (30.0) Reported 2160 (45.0) 220 (4.5) 75 (1.6) 1.5 (0.3) DASHD-HC (48 95) 1920 (40.0) L/ (60.0) 290 (6.0) 300 (6.2) 1.5 (0.3) DAW-R (44 60) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) DAW-LC (48 60) 1200 (25.0) Reported 1800 (37.5) 180 (3.8) 75 (1.6) 1.5 (0.3) DAW-C (48 71) 1440 (30.0) Reported 2160 (45.0) 220 (4.5) 75 (1.6) 1.5 (0.3) DAW-HC (60 99) 1920 (40.0) L/ (60.0) 290 (6.0) 300 (6.2) 1.5 (0.3) DAW-AW (60 99) 1920 (40.0) L/ (60.0) 390 (8.0) 300 (6.2) 0.5 (0.1) FD-R (36 79) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) FD-LC (36 83) 1200 (25.0) Reported 1800 (37.5) 180 (3.8) 75 (1.6) 1.5 (0.3) FD-C (40 83) 1440 (30.0) Reported 2160 (45.0) 220 (4.5) 75 (1.6) 1.5 (0.3) FD-HC (48 95) 1920 (40.0) L/ (60.0) 290 (6.0) 300 (6.2) 1.5 (0.3) FD-AW (60 99) 1920 (40.0 L/ (60.0) 390 (8.0) 300 (6.2) 0.5 (0.1) FW-R (48 48) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) FW-LC (56 56) 1200 (25.0) Reported 1800 (37.5) 180 (3.8) 75 (1.6) 1.5 (0.3) FW-C (60 60) 1440 (30.0) Reported 2160 (45.0) 220 (4.5) 75 (1.6) 1.5 (0.3) FW-HC (60 71) 1920 (40.0) L/ (60.0) 290 (6.0) 75 (1.6) 1.5 (0.3) FW-AW (60 99) 1920 (40.0) L/ (60.0) 390 (8.0) 300 (6.2) 0.5 (0.1) Greenhouse window GH-R x 900 x 300 (36 36 x 12) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) Hinged rescue window HE-R15 Varies 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) Horizontally or vertically pivoted window Horizontal sliding window HP/VP-R (44 60) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) HP/VP-LC (48 60) 1200 (25.0) Reported 1800 (37.5) 180 (3.8) 75 (1.6) 1.5 (0.3) HP/VP-C (48 87) 1440 (30.0) Reported 2160 (45.0) 220 (4.5) 75 (1.6) 1.5 (0.3) HP/VP-HC (60 99) 1920 (40.0) L/ (60.0) 290 (6.0) 300 (6.2) 1.5 (0.3) HP/VP-AW (60 99) 1920 (40.0) L/ (60.0) 390 (8.0) 300 (6.2) 0.5 (0.1) HS-R (63 44) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) HS-LC (71 56) 1200 (25.0) Reported 1800 (37.5) 180 (3.8) 75 (1.6) 1.5 (0.3) HS-C (71 60) 1440 (30.0) Reported 2160 (45.0) 220 (4.5) 75 (1.6) 1.5 (0.3) HS-HC (99 79) 1920 (40.0) L/ (60.0) 290 (6.0) 300 (6.2) 1.5 (0.3) HS-AW (99 79) 1920 (40.0) L/ (60.0) 390 (8.0) 300 (6.2) 1.5 (0.3)
6 Product Type Hung window vertical sliding Product Designation Minimum Test Size, mm (in) Minimum Design Pressure, Pa (lbf/ft 2 ) Deflection at Design Pressure, mm (in) Minimum Structural Pressure, Pa (lbf/ft 2 ) Minimum Water Air Leakage Resistance Pressure, Pa (lbf/ft 2 ) Pa (lbf/ft 2 ) L/s m 2 (cfm/ft 2 ) H-R (40 63) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) H-LC (44 75) 1200 (25.0) Reported 1800 (37.5) 180 (3.8) 75 (1.6) 1.5 (0.3) H-C (56 91) 1440 (30.0) Reported 2160 (45.0) 220 (4.5) 75 (1.6) 1.5 (0.3) H-HC (60 99) 1920 (40.0) L/ (60.0) 290 (6.0) 300 (6.2) 1.5 (0.3) H-AW (60 99) 1920 (40.0) L/ (60.0) 390 (8.0) 300 (6.2) 1.5 (0.3) Jal-awning window JA-R (56 63) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) Jalousie window J-R (36 48) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) Non-hung window vertical sliding Side-hinged door VS-R (40 63) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) VS-LC (44 75) 1200 (25.0) Reported 1800 (37.5) 180 (3.8) 75 (1.6) 1.5 (0.3) VS-C (56 91) 1440 (30.0) Reported 2160 (45.0) 220 (4.5) 75 (1.6) 1.5 (0.3) SHD-R (36 79) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) SHD-LC (36 83) 1200 (25.0) Reported 1800 (37.5) 180 (3.8) 75 (1.6) 1.5 (0.3) SHD-C (40 83) 1440 (30.0) Reported 2160 (45.0) 220 (4.5) 75 (1.6) 1.5 (0.3) SHD-HC (40 83) 1920 (40.0) L/ (60.0) 290 (6.0) 300 (6.2) 1.5 (0.3) SHD-AW (48 95) 1920 (40.0) L/ (60.0) 390 (8.0) 300 (6.2) 0.5 (0.1) Side-hinged window SHW-AW (48 71) 1920 (40.0) L/ (60.0) 390 (8.0) 300 (6.2) 0.5 (0.1) Side lite Sliding door Top-hinged window Transom Tropical awning window (multiple vent) Tropical awning window (single vent) Unit skylight or roof window (glass glazed) Unit skylight or roof window (plastic glazed) SLT-R (16 79) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) SLT-LC (16 83) 1200 (25.0) Reported 1800 (37.5) 180 (3.8) 75 (1.6) 1.5 (0.3) SLT-C (20 83) 1440 (30.0) Reported 2160 (45.0) 220 (4.5) 75 (1.6) 1.5 (0.3) SD-R (71 79) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) SD-LC (87 83) 1200 (25.0) Reported 1800 (37.5) 180 (3.8) 75 (1.6) 1.5 (0.3) SD-C (95 83) 1440 (30.0) Reported 2160 (45.0) 220 (4.5) 75 (1.6) 1.5 (0.3) SD-HC (123 95) 1920 (40.0) L/ (60.0) 290 (6.0) 300 (6.2) 1.5 (0.3) SD-AW (123 95) 1920 (40.0) L/ (60.0) 390 (8.0) 300 (6.2) 1.5 (0.3) TH-C (48 60) 1440 (30.0) Reported 2160 (45.0) 220 (4.5) 75 (1.6) 1.5 (0.3) TH-HC (48 60) 1920 (40.0) L/ (60.0) 290 (6.0) 300 (6.2) 1.5 (0.3) TH-AW (60 99) 1920 (40.0) L/ (60.0) 390 (8.0) 300 (6.2) 0.5 (0.1) TR-R (71 12) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) TR-LC (71 16) 1200 (25.0) Reported 1800 (37.5) 180 (3.8) 75 (1.6) 1.5 (0.3) TR-C (79 20) 1440 (30.0) Reported 2160 (45.0) 220 (4.5) 75 (1.6) 1.5 (0.3) TA-R (48 63) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) TA-LC (56 99) 1200 (25.0) Reported 1800 (37.5) 180 (3.8) 75 (1.6) 1.5 (0.3) TA-C (56 99) 1440 (30.0) Reported 2160 (45.0) 220 (4.5) 75 (1.6) 1.5 (0.3) TA-R (48 24) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) TA-LC (56 28) 1200 (25.0) Reported 1800 (37.5) 180 (3.8) 75 (1.6) 1.5 (0.3) TA-C (56 28) 1440 (30.0) Reported 2160 (45.0) 220 (4.5) 75 (1.6) 1.5 (0.3) SKG/RW-R (20 44) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) SKG/RW-C (44 44) 1440 (30.0) Reported 2160 (45.0) 220 (4.5) 75 (1.6) 1.5 (0.3) SKG/RW-HC (44 95) 1920 (40.0) L/ (60.0) 290 (6.0) 300 (6.2) 1.5 (0.3) SKP/RW-R (20 44) 720 (15.0) Reported 1080 (22.5) 140 (2.9) 75 (1.6) 1.5 (0.3) SKP/RW-C (44 44) 1440 (30.0) Reported 2160 (45.0) 220 (4.5) 75 (1.6) 1.5 (0.3) SKP/RW-HC (44 95) 1920 (40.0) L/ (60.0) 290 (6.0) 300 (6.2) 1.5 (0.3) TABLE 25 GATEWAY PERFORMANCE REQUIREMENTS
7
8 CMB-5-05 AAMA/WDMA/CSA 101/I.S.2/A440-05, EXCERPT Copyright 2005 American Architectural Manufacturers Association 1827 Walden Office Square, Suite 550 Schaumburg, IL USA Window & Door Manufacturers Association 1400 East Touhy Avenue, Suite 470 Des Plaines, IL USA Canadian Standards Association 5060 Spectrum Way, Suite 100 Mississauga, Ontario, L4W 5N6 Canada This document is an excerpt of AAMA/WDMA/CSA 101/I.S.2/A AAMA/WDMA/CSA 101/I.S.2/A was developed by representative members of AAMA, WDMA and CSA as advisory information and published as a public service. AAMA, WDMA and CSA disclaim all liability for the use, application or adaptation of materials published herein.
Specifying Windows. Performance Standards
1 Specifying Windows and ddoors Using Performance Standards 2 This program is registered with the AIA/CES for continuing professional education. As such, it does not include content that may be deemed
T H E A A M A C E R T I F I C A T I O N P R O G R A M
T H E A A M A C E R T I F I C A T I O N P R O G R A M AAMA STANDS FOR QUALITY Since 1962, AAMA Certification, the original third-party window performance program, has provided manufacturers with the means
NAFS and The 2012 Building Code
NAFS and The 2012 Building Code Presented to BCBEC on 2013-04-18 Al Jaugelis B.Sc. Arch. [email protected] NAFS changes everything... No more ABC s New concepts New terminology New rating system New
TEST REPORT. Rendered to: INTERNATIONAL WINDOW Hayward, California. PRODUCT TYPE: Aluminum Hopper SERIES/MODEL: 7222
Architectural Testing TEST REPORT Report No.: C2375.01-301-44 Rendered to: INTERNATIONAL WINDOW Hayward, California PRODUCT TYPE: Aluminum Hopper SERIES/MODEL: 7222 SPECIFICATIONS: AAMA/WDMA/CSA 101/I.S.2/A440-05,
AAMA/WDMA/CSA 101/I.S.2/A440-05 TEST REPORT. Rendered to: EAGLE WINDOW & DOOR COMPANY
Architectural Testing AAMA/WDMA/CSA 101/I.S.2/A440-05 TEST REPORT Rendered to: EAGLE WINDOW & DOOR COMPANY SERIES/MODEL: Series 01 Axiom Clad One-Piece Casement Fixed 6060 PRODUCT TYPE: Aluminum Clad Fixed
TEST REPORT. Report No.: B3404.01-801-47. Rendered to: CROFT, LLC. Magnolia, Mississippi. PRODUCT TYPE: Aluminum Single Hung Window SERIES/MODEL: 95
Architectural Testing TEST REPORT Report No.: B3404.01-801-47 Rendered to: CROFT, LLC. Magnolia, Mississippi PRODUCT TYPE: Aluminum Single Hung Window SERIES/MODEL: 95 SPECIFICATION: AAMA/WDMA/CSA 101/I.S.2/A440-08,
Quality Assurance and Diagnostic Water Leakage Field Check of Installed Storefronts, Curtain Walls and Sloped Glazing Systems
Method of Test Committee Approval Product Group Approval Approved via 5/21/15 MOT CC Out for Ballot (#805-15) PUBLICATION NO. AAMA 501.2-XX DRAFT #2 DATED 5/21/15 Quality Assurance and Diagnostic Water
TEST REPORT. Rendered to: TFC A DIVISION OF CENTURION INDUSTRIES, INC. Garrett, Indiana
Architectural Testing TEST REPORT Report No.: D0162.02-201-44 Rendered to: TFC A DIVISION OF CENTURION INDUSTRIES, INC. Garrett, Indiana PRODUCT TYPE: Pressure Equalized Rainscreen SERIES/MODEL: 4 mm Composite
ALUMINUM Guide Spec: Standard Aluminum Windows & Doors
ALUMINUM Guide Spec: Standard Aluminum Windows & Doors Standard Aluminum Windows ALUMINUM WINDOWS - 08 51 13 With the thin lines that Migard s Aluminum Windows provide, they are ideal for both new construction
Size & Range. for windows & doors. Company
Size & Range for windows & doors A Company B General information windows and doors Sizes This catalogue contains all Airlite s standard sizes for windows and doors. These are the ones that we make every
Table of Contents PART 1 WINDOW SELECTION GUIDE. Window and Door Selection Guide
VOLUME 1 - WINDOWS AND DOORS Window and Door Selection Guide PART 1 WINDOW SELECTION GUIDE WSG-11 PART 2 - PERFORMANCE SPECIFICATIONS Voluntary Specifications for Aluminum, Vinyl (PVC) and Wood Windows
Evaluating the Field Performance of Windows and Curtain Walls of Large Buildings
Best2 Airtightness of Buildings Session WB6-2 Evaluating the Field Performance of Windows and Curtain Walls of Large Buildings Mario D. Gonçalves, Patenaude-Trempe and Robert Jutras, Air-Ins Introduction
TEST REPORT. Report No.: A9814.01 109 44. Rendered to: BAMCO INC. Middlesex, New Jersey. PRODUCT TYPE: Wall Cladding System SERIES/MODEL: Dry Concept
Architectural Testing TEST REPORT Report No.: A9814.01 109 44 Rendered to: BAMCO INC. Middlesex, New Jersey PRODUCT TYPE: Wall Cladding System SERIES/MODEL: Dry Concept AAMA 508 07, Voluntary Test Method
Window Types and Materials
Window Types and Materials There are many window designs in use today: a) Awnings (Top-Hinged) b) Casement (Side-Hinged) c) Picture (Fixed) d) Horizontal Slider e) Single Hung f) Double Hung g) Tilt and
continuing professional education. As such, it construed to be an approval or endorsement by
This program is registered with the AIA/CES for continuing professional education. As such, it does not include content that may be deemed or construed to be an approval or endorsement by the AIA of any
MOCK-UP TEST REPORT. Rendered to: TUBELITE, INC. PROJECT: 200 Series Curtain Wall Mock-Up
MOCK-UP TEST REPORT Rendered to: TUBELITE, INC. PROJECT: 200 Series Curtain Wall Mock-Up Report No: 85616.01-120-32 Test Completion Date: 01/15/09 Report Date: 02/11/09 Record Retention End Date: 01/15/13
Tuscany Series Vinyl Replacement Windows 3-Part Specification
PART 1 - GENERAL SECTION 08 53 13 (Masterformat 2004 Edition) VINYL WINDOWS Tuscany is optimized for replacement applications but since it is available in multiple frame styles including nail-on fin frame,
IAN BENNIE AND ASSOCIATES TEST REPORT NO. 2014-023-S2 AWNING WITH FIXED WINDOW PROTOTYPE TEST to AS2047-1999. for. Finesse Window Systems Australia
IAN BENNIE AND ASSOCIATES TEST REPORT NO. 2014-023-S2 AWNING WITH FIXED WINDOW PROTOTYPE TEST to AS2047-1999 for Finesse Window Systems Australia November 2014 Accreditation No. 2371 Accredited for compliance
Astragal: a vertical member placed at the meeting edges of a double door to provide a weather seal and may be used to anchor the fixed door.
Window and Door Dictionary AAMA: American Architectural Manufacturers Association. A national trade association that establishes voluntary standards for the window, door, and skylight industry. Ambient
A ROAD MAP FOR YOUR CODE, SMOKE BARRIER & SMOKE PARTITION REQUIREMENTS
A ROAD MAP FOR YOUR CODE, SMOKE BARRIER & SMOKE PARTITION REQUIREMENTS International Code Council National Fire Protection Association Underwriters Laboratories Inc. 5203 Leesburg Pike, Suite 600 1 Batterymarch
ASTM E 1886 / ASTM E 1996 AND ASTM E 283, ASTM E 330, ASTM E 331 TEST REPORT. Rendered to: BEKAERT SPECIALTY FILMS, LLC
ASTM E 1886 / ASTM E 1996 AND ASTM E 283, ASTM E 330, ASTM E 331 TEST REPORT Rendered to: BEKAERT SPECIALTY FILMS, LLC SERIES/MODEL: Panorama 8-mil Film PRODUCT TYPE: Fixed Window with Applied Film This
CHAPTER 24 GLASS AND GLAZING
CHAPTER 24 GLASS AND GLAZING SECTION 2401 GENERAL 2401.1 Scope. The provisions of this chapter shall govern the materials, design, construction and quality of glass, lighttransmitting ceramic and light-transmitting
PERFORMANCE TEST REPORT. Rendered to: BAMCO INC. PRODUCT TYPE: ACM Wall Panel Systems
PERFORMANCE TEST REPORT Rendered to: BAMCO INC. PRODUCT TYPE: ACM Wall Panel Systems Summary of Results Title Test Specimen #1 Test Specimen #2 Air Infiltration
AAMA 2400-10. Standard Practice for Installation of Windows with a Mounting Flange in Open Stud Frame Construction for Low Wind/Water Exposure
A M E R I C A N A R C H I T E C T U R A L AAMA 2400-10 Standard Practice for Installation of Windows with a Mounting Flange in Open Stud Frame Construction for Low Wind/Water Exposure M A N U F A C T U
DuPont Tyvek Commercial Air Barrier Assemblies Exceed Air Barrier Association of America, ASHRAE 90.1
Building Science Bulletin DuPont Tyvek Commercial Air Barrier Assemblies Exceed Air Barrier Association of America, ASHRAE 90.1 and IECC Air Leakage Requirements When Tested in Accordance with ASTM E2357
TECHNICAL MANUAL. airlite.com.au
PAGE Awning Windows 1 Casement Windows 7 Double Hung Windows 14 Sliding Windows 21 Sliding Doors 28 Bi-fold Doors 38 Hinged Doors 45 Stacking Doors 54 airlite.com.au AWNING WINDOWS Building In brick veneer
PERFORMANCE TEST REPORT. Rendered to: UNITED STATES ALUMINUM CORPORATION. SERIES/MODEL: 450 Center Glaze PRODUCT TYPE: Aluminum Curtain Wall
Architectural Testing PERFORMANCE TEST REPORT Rendered to: UNITED STATES ALUMINUM CORPORATION SERIES/MODEL: 450 Center Glaze PRODUCT TYPE: Aluminum Curtain Wall Title Summary of Results Air Infiltration
Excerpts from the Canadian National Building Code (NBC)
Excerpts from the Canadian National Building Code (NBC) Reproduced here with Permission of the Copyright Owner, the National Research Council of Canada, Institute for Research in Construction. For more
Scottsdale, Arizona. Presentation by: Hermes Norero, P.E. President and CEO
Scottsdale, Arizona Presentation by: Hermes Norero, P.E. President and CEO Mr. Hermes F. Norero, P.E. is the founder and President of Building Drops. The concept of Building Drops first arose after realizing,
Relevant British, European and International standards
Relevant British, European and International standards BS 1245:1975 Specification for metal door frames (steel) BS 3621:2007 + A1:2009 Thief resistant lock assemblies - Key egress BS 476-20:1987 Fire tests
PERFORMANCE EVALUATION OF THE CERAMITEX RVR SYSTEM IN ACCORDANCE WITH AAMA 508-07 FOR PRESSURE EQUALIZATION BEHAVIOR & WATER PENETRATION RESISTANCE
PERFORMANCE EVALUATION OF THE CERAMITEX RVR SYSTEM IN ACCORDANCE WITH AAMA 508-07 FOR PRESSURE EQUALIZATION BEHAVIOR & WATER PENETRATION RESISTANCE Report to: Ceramitex Inc. 520 Clarke Rd. London, Ontario
Glossary. Argon: An inert, nontoxic gas used in insulating glass units to reduce heat transfer.
Glossary AAMA : American Architectural Manufacturers Association, a national trade association that established voluntary standards for the window, door and skylight industry. Argon: An inert, nontoxic
PERFORMANCE TEST REPORT
PERFORMANCE TEST REPORT CCLW JOB #08-5152-1 DATES OF FORMAL TESTING SEPTEMBER 19 & 23, 2008 TEST LOCATION CONSTRUCTION CONSULTING LABORATORY WEST 4751 WEST STATE STREET, SUITE B ONTARIO, CA 91762 PH: 909-591-1789
Testing Water Penetration Resistance of Window Systems Exposed to Realistic Dynamic Air Pressures
Testing Water Penetration Resistance of Window Systems Exposed to Realistic Dynamic Air Pressures R. A. Van Straaten 1, G. A. Kopp 2, J. F. Straube 3 1 Research Lab for Better Homes, University of Western
PERFORMANCE TEST REPORT. Rendered to: TREMCO INCORPORATED. SERIES/MODEL: Proglaze ETA PRODUCT TYPE: Engineered Transition Assembly
PERFORMANCE TEST REPORT Rendered to: TREMCO INCORPORATED SERIES/MODEL: Proglaze ETA PRODUCT TYPE: Engineered Transition Assembly Title Summary of Results Air Infiltration
Field Water Testing - Lessons Learned
Quicklinks Lots of Questions - How About Answers Let's Start with the Specifications Test Methods VS. Performance Standard Using the Correct Test Method Conclusion About the Author Compilation of Test
PERFORMANCE TEST REPORT. Rendered to: ARCHITECTURAL METAL SOLUTIONS, INC.
PERFORMANCE TEST REPORT Rendered to: ARCHITECTURAL METAL SOLUTIONS, INC. SERIES/MODEL: AMS ARMOR-LOCK PRODUCT TYPE: STANDING SEAM METAL ROOF PANEL SYSTEM Report No: 97123.02-901-44 Test Date: 05/17/10
HMMA 810 HOLLOW METAL DOORS HOLLOW METAL MANUAL -87 NAAMM STANDARD FOURTH EDITION METAL DOORS & FRAMES NAAMM 2 NAAMM 2 METAL DOORS & FRAMES
HOLLOW METAL MANUAL NAAMM STANDARD HMMA 810-87 8d METAL DOORS & FRAMES NAAMM 2 87 HOLLOW METAL HOLLOW METAL DOORS FOURTH EDITION NAAMM 2 87 8d METAL DOORS & FRAMES A Division of NATIONAL ASSOCIATION OF
DOMUS & ALDUS THE WINDOW CONCEPT WITH A STUNNINGLY MODERN APPEARANCE
DOMUS & ALDUS THE WINDOW CONCEPT WITH A STUNNINGLY MODERN APPEARANCE MODERN DESIGN DOMUS & ALDUS 2 3 ALDUS & DOMUS PRODUCT DETAILS 1 2 3 Option of glazing bar Architectural designed handle Option of trickle
CHAPTER 24 GLASS AND GLAZING
CHAPTER 24 GLASS AND GLAZING SECTION 2401 GENERAL 2401.1 Scope. The provisions of this chapter shall govern the materials, design, construction and quality of glass, lighttransmitting ceramic and light-transmitting
PERFORMANCE TEST REPORT. Rendered to: GLASSCRAFT DOOR COMPANY
PERFORMANCE TEST REPORT Rendered to: GLASSCRAFT DOOR COMPANY SERIES/MODEL: Buffalo Forge Steel Doors / Round Top Single PRODUCT TYPE: In-swing Round Top Single Door RH-4 Title Uniform Load Deflection Test
MINNESOTA DEPARTMENT OF PUBLIC SAFETY State Fire Marshal Division STATEMENT OF POLICY. State Fire Marshal
MINNESOTA DEPARTMENT OF PUBLIC SAFETY State Fire Marshal Division STATEMENT OF POLICY Policy #: Subject of Policy: INS-04 (2007) Escape Windows Revised and Approved By: Title: Jerry Rosendahl State Fire
research highlight Water Penetration Resistance of Windows - Study of Codes, Standards,Testing, and Certification
research highlight November 2003 Technical Series 03-125 Water Penetration Resistance of Windows - Study of Codes, Standards,Testing, and Certification introduction Over the past decade, there has been
A site plan or floor plan clearly identifying the location(s) of all new replacement window(s)
WINDOW REPLACEMENT GUIDELINES Community Development Planning & Building 2263 Santa Clara Ave., Rm. 190 Alameda, CA 94501-4477 alamedaca.gov 510.747.6800 F: 510.865.4053 TDD: 510.522.7538 Hours: 7:30 a.m.
The replacement or modification of existing windows shall comply with the following requirements:
City of La Habra Heights Building Division 1245 N. Hacienda Road La Habra Heights, CA 90631 Office: (562) 694-6302 ext. 228 Fax: (562) 690-5010 WINDOW REPLACEMENT 2010 CALIFORNIA RESIDENTIAL CODE (CRC)
MIAMI-DADE COUNTY PERFORMANCE TEST REPORT. Report No.: B8049.01-401-18. Rendered to: AMERICAN PRODUCTS, INC Tampa, Florida
Architectural Testing MIAMI-DADE COUNTY PERFORMANCE TEST REPORT Report No.: B8049.01-401-18 Rendered to: AMERICAN PRODUCTS, INC Tampa, Florida PRODUCT TYPE: Aluminum Storefront with Double Doors SERIES/MODEL:
City of Peterborough
City of Peterborough Building Division Basement Finishing Guide Residential Information Guides This information is intended to be used as an guide that outlines minimum requirements when finishing a basement,
WINDOW AND DOOR REPLACEMENT REQUIREMENTS
WINDOW AND DOOR REPLACEMENT REQUIREMENTS Should you have any questions after reading the following information, please call the Building Inspection Department at 651-439-4439 to discuss the topics of concern.
CERTIFICATE OF APPROPRIATENESS Planning and Development Department, Neighborhood Services
Owner: Midas Equity, LLC. Applicant: Nine Lite Construction Time Frame Date Accepted April-12-2011 90-day Waiver N/A SITE INFORMATION: Lot 7, Block 247, Houston Heights Subdivision,, Harris County, Texas.
Installer Training and Certification Overview
Installer Training and Certification Overview Outline of This Presentation The Need for a Training Program The History of the Program Details of the Training Program The Certification Process The Need
Series 3502 Thermal Series 3902 Fixed Thermal 3 1 4 Architectural Grade Horizontal Sliding Window
Windows Curtain Walls Entrances Storefronts Series 3502 Thermal Series 3902 Fixed Thermal 3 1 4 Architectural Grade Horizontal Sliding Window Configurations XO OX XOX Fixed Series 3502 retains an AAMA
Victims Compensation Claim Status of All Pending Claims and Claims Decided Within the Last Three Years
Claim#:021914-174 Initials: J.T. Last4SSN: 6996 DOB: 5/3/1970 Crime Date: 4/30/2013 Status: Claim is currently under review. Decision expected within 7 days Claim#:041715-334 Initials: M.S. Last4SSN: 2957
AutoCAD Architecture 2012 UK Content Tools
AutoCAD Architecture 2012 UK Content Tools Contents Contents... 1 Installation... 2 Loading the utilities... 2 Utilities Overview... 3 Menu and Toolbar... 3 Content Generation... 3 Content Publishing...
How To Test For An Architectural Test
Architectural Testing ASTM E 1886 and ASTM E 1996 TEST REPORT Rendered to: CORAL ARCHITECTURAL PRODUCTS SERIES/MODEL: PW 256 with Door Openings PRODUCT TYPE: Aluminum Impact Resistant Curtain Wall System
REPORT NUMBER: 100900226COQ-003 ORIGINAL ISSUE DATE: July 19, 2013
REPORT NUMBER: 100900226COQ-003 ORIGINAL ISSUE DATE: July 19, 2013 TEST REPORT EVALUATION CENTER INTERTEK TESTING SERVICES NA LTD. 1500 BRIGANTINE DRIVE COQUITLAM, BC V3K 7C1 CANADA RENDERED TO PHOENIX
Windows & Doors Standard Sizes
Windows & Doors Standard Sizes Version Six 2012 General information windows and doors Sizes This catalogue contains all Stegbar s standard sizes for windows and doors. These are the ones that we make every
Introduction...COMB-2 Design Considerations and Examples...COMB-3
SECTION DIRECTORY General Information Introduction...COMB-2 Design Considerations and Examples...COMB-3 Combination Assembly Recommendations and Limitations Composite Configurations...COMB-4 Typical Sealant
City of San Diego, CWP Guidelines
PART 1 -- GENERAL SECTION 08520-1.1 WORK OF THIS SECTION City of San Diego, CWP Guidelines A. The WORK of this Section includes providing aluminum windows with frames, bracing, glazing attachments, screens,
Sample Calculations...V-CR-12. Door and Window Typical Combinations... V-CR-12 Horizontal and Vertical Typical Combinations...
SECTION DIRECTORY General Information Definitions...V-CR- Design Considerations...V-CR- Composite Configurations...V-CR-4 Design Considerations and Examples for Typical Window and Door Combinations...V-CR-5
Evidence of Performance. Class 2. Class 5A. Class C4 / B4. Test Report No. 15-003655-PR01. ift Rosenheim 16.12.2015
Evidence of Performance Test Report No. 15-003655-PR01 (PB-A01-02-en-01) Client Product Designation Performance-relevant product details Overall dimensions (W x H) Special features Alüminyum San. Tic.
Dollars & Sense of Compliance!
CRCA s 29 th Annual Trade Show Oakbrook k Terrace, IL January 19 20, 2012 Dollars & Sense of Compliance! Mark S. Graham Associate ExecutiveDirector Director, Technical Services National Roofing Contractors
Insider Tips for Purchasing Replacement Windows
Insider Tips for Purchasing Replacement Windows From the experts at Legacy Remodeling WE SPEAK REMODELING Table of Contents Introduction Page 3 Window Styles Page 4 Window Materials Page 6 Window Efficiency
Evidence of Performance Resistance to wind load Watertightness Air permeability
Evidence of Performance Resistance to wind load Watertightness Air permeability Test Report 102 43093/1e Client Product YILDIZPEN PLASTIK SAN. VE TIC. LTD. STI. A.O.S.B 10039 Street No:18 Çigli Izmir Turkey
SECTION 07 42 13 METAL WALL PANELS
Mitsubishi Plastics Composites America, Inc. 401 Volvo Parkway Chesapeake, VA 23320 Phone: (800) 422-7270 Fax: (757) 436-1896 E-mail: [email protected] www.alpolic-northamerica.com This MANU-SPEC utilizes
Casement/Awning Window Parts Reference Catalog
Casement/Awning Window Parts Reference Catalog (Includes Miscellaneous Parts for Eyebrow Casement and Garden Bay Windows) #1028654 (Revised 03/02) Weather Shield Mfg., Inc. Medford, WI 54451 715/748-2100
TOPLIGHTS. NOTE: 2.4m high sliding doors are only available in certain configurations and sizes.
NOTE: 2.4m high sliding doors are only available in certain configurations and sizes. Eagle Sidelights & Toplights Sidelights and Toplights are designed to clip onto the Eagle patio door system. The Sidelights
Product information. Schüco Window AWS 65. 03.2009/Web Schüco AWS 65 1-11
Schüco Window AWS 65 The basic window system, Schüco Window AWS 65, with a comprehensive range for imaginative designs, is particularly suitable for block constructions with a basic depth of 65 mm. Features
SECTION 08 41 1 ALUMINUM FRAMED ENTRANCES and STOREFRONTS. System 402 Flush-Glazed Screw Spline Storefront
PART 1 GENERAL 1.01 Work Included SECTION 08 41 1 ALUMINUM FRAMED ENTRANCES and STOREFRONTS System 402 Flush-Glazed Screw Spline Storefront A. Furnish and install aluminum architectural storefront system
Replacement Windows and Doors
Replacement Windows and Doors Short Policy Guide: Need for Planning Permission and Listed Building Consent For Replacement Windows and Doors Produced by City Development Department, Dundee City Council,
Vestibule Case Study. Vestibule Requirement Intent [2003 IECC, 2006 IECC, 2003 IBC, 2006 IBC, 90.1-2001, 90.1-2004]
![Vestibule Case Study. Vestibule Requirement Intent [2003 IECC, 2006 IECC, 2003 IBC, 2006 IBC, 90.1-2001, 90.1-2004]](/thumbs/24/2939769.jpg "Vestibule Case Study. Vestibule Requirement Intent [2003 IECC, 2006 IECC, 2003 IBC, 2006 IBC, 90.1-2001, 90.1-2004]")
Vestibule Case Study [2003 IECC, 2006 IECC, 2003 IBC, 2006 IBC, 90.1-2001, 90.1-2004] Vestibule Requirement Intent Page 1 of 14 The primary intent behind the requirement for a vestibule is to reduce infiltration
SECTION 08 53 13 VINYL WINDOWS. A. The General Conditions, Supplementary Conditions, and Division 01 - Requirements apply.
SECTION 08 53 13 VINYL WINDOWS PART 1 - GENERAL 1.1 CONDITIONS AND REQUIREMENTS A. The General Conditions, Supplementary Conditions, and Division 01 - Requirements apply. 1.2 SECTION INCLUDES A. Double
JANUARY, 2016 TR-7100 Windows (Fixed) 1 EC 97909-071 085113 ALUMINUM WINDOWS Guide Specs
JANUARY, 2016 TR-7100 Windows (Fixed) 1 EC 97909-071 085113 ALUMINUM WINDOWS Guide Specs SECTION 085113 ALUMINUM WINDOWS This suggested guide specification has been developed using the current edition
Impact-Resistant Windows and Sliding Glass Doors
Impact-Resistant Windows and Sliding Glass Doors Make Your Home A SafeHarbor. SafeHarbor Impact-Resistant Windows and Sliding Glass Doors are designed to look like traditional windows and doors, but they
ASTM E 1886 and ASTM E 1996 TEST REPORT. Rendered to: Atrium Companies, Inc. SERIES/MODEL: 50/305 HS PRODUCT TYPE: Vinyl Horizontal Slider
ASTM E 1886 and ASTM E 1996 TEST REPORT Rendered to: Atrium Companies, Inc. SERIES/MODEL: 50/305 HS PRODUCT TYPE: Vinyl Horizontal Slider Report No.: Test Date: 5/21/07 Through: 5/23/07 Report Date: 5/30/07
Enhancing The Beauty And Value Of Your Home. Exclusive Patio Door Collection. NORTH STAR PATIO DOOR COLLECTION Two-Panel Three-Panel Four-Panel
Enhancing The Beauty And Value Of Your Home. Exclusive Patio Door Collection. NORTH STAR PATIO DOOR COLLECTION Two-Panel Three-Panel Four-Panel Since 1985 North Star has been an industry leader in the
Quality Windows And Doors. Great Service. Exceptional Value.
Quality Windows And Doors. Great Service. Exceptional Value. As A Matter Of Fact, Our Windows And Doors Are The Best. Since 1985 North Star has been an industry leader in the manufacture of attractive
Application for a Window Replacement Master Plan Curtis B. Wayne, Architect Ken Lustbader, Preservation Consultant
Application for a Window Replacement Master Plan Curtis B. Wayne, Architect Ken Lustbader, Preservation Consultant 37 West 12 th Street Between 5 th and 6 th Avenues Architectural History Architectural
Window Installation Instructions
Caution The correct installation methods of windows in full frame or insert applications is critical towards achieving the tested performance of the window and longterm enjoyment and energy savings for
Quality Windows And Doors. Great Service. Exceptional Value.
Quality Windows And Doors. Great Service. Exceptional Value. As A Matter Of Fact, Our Windows And Doors Are The Best. Since 1985 North Star has been an industry leader in the manufacture of attractive
IECC Compliance Guide for Homes in Virginia
IECC Compliance Guide for Homes in Virginia Amended Version of 2012 International Energy Conservation Code July 14, 2014 Climate Zone Since the entire state of Virginia falls in the IECC Climate Zone 4,
Glossary. 1/3 1/3 1/3 - Configuration of a vent-fixed-vent (xox) window in which the vents and fixed panel are equal sizes
Glossary 1/3 1/3 1/3 - Configuration of a vent-fixed-vent (xox) window in which the vents and fixed panel are equal sizes 1/4 1/2 1/4 - Configuration of a vent-fixed-vent (xox) window in which the vents
Residential Windows, 3 rd edition Corrected index 1
Residential Windows, 3 rd edition Corrected index 1 A absorptance definition, 78 determinants of, 78 79 energy performance and, 78 tinted glass, 84 acoustical properties of windows, 60 61 acrylic glazing
NanaWall SL73 - Thermally Broken Aluminum Framed Hurricane Rated Folding System with Miami Dade County, Florida NOA
NanaWall SL73 - Thermally Broken Aluminum Framed Hurricane Rated Folding System with Miami Dade County, Florida NOA ❶ PART 1 - GENERAL 1.01 SUMMARY A. Section Includes: Sliding/folding aluminum and glass
THE ULTIMATE HIGH PERFORMANCE REPLACEMENT WINDOWS AND PATIO DOORS
THE ULTIMATE HIGH PERFORMANCE REPLACEMENT WINDOWS AND PATIO DOORS EXCLUSIVELY BY NORANDEX Put our reputation in your home. At Norandex, we are proud to be a wellrespected leader in the home improvement
Building Control Guidance Note
Issued 01/01/13 Rev Page 1 of 5 If you intend to convert an existing loft space into additional rooms you will need to apply for Building Regulation Approval. You may also need Planning Permission if you
Installation Detailed installation instructions are provided which should be strictly followed.
Specification System 6 The Metal Technology Thermally-Broken Vertical Slide Window has been designed in such a way that its'attractive and clean lines will enhance all types of residential and commercial
MIAMI-DADE COUNTY PERFORMANCE TEST REPORT. Report No.: B9460.01-109-18. Rendered to: CAPTIVEAIRE, INC. Blue Bell, Pennsylvania
Architectural Testing MIAMI-DADE COUNTY PERFORMANCE TEST REPORT Report No.: B9460.01-109-18 Rendered to: CAPTIVEAIRE, INC. Blue Bell, Pennsylvania PRODUCT TYPE: Roof Mounted Exhaust Fan SERIES/MODEL: CASRE
2012 Ontario Building Code Requirements for New Construction. Bradford West Gwillimbury Building Division March 5, 2012
2012 Ontario Building Code Requirements for New Construction Bradford West Gwillimbury Building Division March 5, 2012 1 Ontario Building Code changes Applicable to permits applied for after December 31,
WATER TESTING MISCONCEPTIONS: F ENESTRATION PRODUCT CERTIFICATION AND FORENSIC INVESTIGATION OF BUILDING LEAKAGE
WATER TESTING MISCONCEPTIONS: F ENESTRATION PRODUCT CERTIFICATION FORENSIC INVESTIGATION OF BUILDING LEAKAGE F RANCESCO J. SPAGNA, PE; SIMPSON GUMPERTZ BRON S. BUCHBERG, PE HEGER, INC. 41 Seyon Street,
western transforming space window systems series 670 a new option for hinged window line
western window systems a new option for transforming space series 670 hinged window line Western Window Systems a new way to live, a better way to build Since opening in 1959 in Phoenix, Western Window
to encourage high quality tropical vernacular Queensland architecture throughout the Shire;
9.1 BUILDING DESIGN & ARCHITECTURAL ELEMENTS Intent The intent of this Policy is to specify and illustrate the architectural elements and building design features considered appropriate for residential
ENERGY EFFICIENT WINDOWS & DOORS A GUIDE TO THERMAL PERFORMANCE. www.rehau.co.uk. Building Solutions Automotive Industry
ENERGY EFFICIENT WINDOWS & DOORS A GUIDE TO THERMAL PERFORMANCE www.rehau.co.uk Building Solutions Automotive Industry INTRODUCTION IMPROVING THE ENERGY EFFICIENCY OF WINDOWS AND DOORS Background Environmental
Section 08520 - Aluminum Windows (4600 Series Specifications)
Section 08520 - Aluminum Windows (4600 Series Specifications) I. GENERAL: 1.01 Scope of Work A. Furnish all necessary materials, labor, and equipment for the complete installation of aluminum windows for
Garden Windows Builders Vinyl
TABLE OF CONTENTS Specifications... 8-2 QuickSpecGuide... 8-3 Elevations/Sizes: 1/4 Scale GardenUnits... 8-4 Grille Patterns... 8-5 SectionDetails: 6 Scale... 8-6 December 2008 JELD-WEN reserves the right
REPORT ON THE TESTING OF SEALED UNITS TO VERIFY THE IMPACT OF PRESSURE EQUALISATION ON INSULATION VALUES.
REPORT ON THE TESTING OF SEALED UNITS TO VERIFY THE IMPACT OF PRESSURE EQUALISATION ON INSULATION VALUES. Author: Dr D A Oloke (School of Technology and the Built Environment, University of Wolverhampton)
2009 IECC Update. Scope. Content. International Energy Conservation Code
2009 IECC Update International Energy Conservation Code Scope The code applies to both residential and commercial buildings. In the code, the United States is divided into eight climate zones which are