Tuscany Series Vinyl Replacement Windows 3-Part Specification

Transcription

1 PART 1 - GENERAL SECTION (Masterformat 2004 Edition) VINYL WINDOWS Tuscany is optimized for replacement applications but since it is available in multiple frame styles including nail-on fin frame, the series is appropriate for new construction SUMMARY A. Section includes: Tubular extruded poly vinyl chloride (PVC) windows of the following type(s): 1. Horizontal sliding windows. 2. Double sliding windows. 3. Single-hung windows. 4. Double-hung tilt windows. 5. Casement windows. 6. Awning windows. 7. Picture and radius windows. 8. Fixed casement windows. 9. Fixed awning windows. 10. Replacement cable bay windows. 11. Bay windows. 12. Bow windows. 13. Garden windows (Classic Series). 14. Jalousie windows. B. Related Sections: INSERT APPROPRIATE SECTION NUMBERS AND TITLES BELOW FOR WINDOW FLASHING AND INSTALLATION SEALANTS Vinyl Sliding Doors. INCLUDE APPROPRIATE LANGUAGE BELOW IF PRODUCTS SPECIFIED IN THIS SECTION ARE TO BE BID AS ALTERNATES. OTHERWISE DELETE FOLLOWING PARAGRAPH. C. Alternates: 1. Reference Section Alternates SUBMITTALS A. Reference Section Submittal Procedures; submit following items: 1. Product Data. 2. Shop Drawings: Include window schedule, window elevations, sections and details, and multiple window assembly details. 3. Samples: a. Color samples: Minimum 1x4 inch (25x100 mm) samples of PVC with integral color. b. Glass, showing specified tint color. 4. Quality Assurance/Control Submittals: a. Qualifications: Proof of manufacturer's qualifications. b. U-Factor and structural rating charts required for AAMA and NFRC labeling requirements. c. Installation Instructions - AAMA ( Mounting Flange Installation ) or AAMA 2410 ( Flush Fin Installation ). GUIDE SPEC 8000T-2

2 B. Closeout Submittals: Reference Section Closeout Submittals; submit following items: 1. Temporary window labels marked to identify windows that labels were applied to. 2. Maintenance instructions. 3. Special Warranties QUALITY ASSURANCE A. Overall Standards: Comply with ANSI/AAMA 101.I.S.2, except as otherwise noted herein. B. Qualifications: 1. Manufacturer Qualifications: a. Minimum five years experience in producing vinyl windows of the type(s) specified. b. Member AAMA, NFRC. C. Regulatory Requirements: INSERT LOCAL REGULATORY REQUIREMENTS BELOW. D. Certifications for insulated glass windows: 1. AAMA: Windows shall be Gold Label certified with label attached to frame per AAMA requirements. 2. NFRC: Windows shall be NFRC certified with temporary U-factor label applied to glass and an NFRC tab added to permanent AAMA frame label DELIVERY, STORAGE, AND HANDLING A. Reference Section Product Storage and Handling Requirements. B. Follow manufacturer's instructions on label applied to windows WARRANTY SELECT RESIDENTIAL WARRANTY BELOW FOR OWNER OCCUPIED SINGLE FAMILY RESIDENTIAL AND OWNER OCCUPIED CONDOMINIUM PROJECTS. SELECT COMMERCIAL WARRANTY FOR NON-OWNER OCCUPIED CONDOMINIUMS, COMMERCIAL, AND MULTI-FAMILY PROJECTS. A. Residential Special Warranty: 1. Lifetime guarantee to original owner. 2. Lifetime glass breakage guarantee to original owner. 3. Transferability: a. Permit unlimited transfer of ownership in first ten years. b. Upon first transfer of ownership, guarantee period shall become ten years from date of original purchase. 4. Guarantee windows against defect in materials and workmanship including costs for parts and labor. A. Commercial Special Warranty: year guarantee. 2. Guarantee windows against defects in materials and workmanship including costs for parts and labor. PART 2 - PRODUCTS 2.01 MANUFACTURER OR A. Milgard Manufacturing, Inc. Tel: MILGARD ( ) th Avenue East (253) Tacoma, WA Fax: (253) GUIDE SPEC 8000T-3 Website: milgard.com

3 INSERT NAME, ADDRESS AND PHONE NUMBERS OF MANUFACTURER'S REPRESENTATIVE BELOW. 1. Manufacturer's Representative: Tel: Fax: B. Window Series: Milgard Tuscany. C. Substitutions: Reference Section Product Substitution Procedures MATERIALS A. Vinyl: Integral color PVC compound containing impact-resistant solid plasticizer, titanium dioxide UV inhibitor, and surface and color stabilizers. 1. Comply with ASTM D 4216 and ANSI/AAMA 101/I.S.2. VERIFY THAT WINDOW FLASHING MATERIAL AND INSTALLATION SEALANT IS SPECIFIED IN APPROPRIATE SECTIONS GENERAL PERFORMANCE REQUIREMENTS A. Thermal Performance: Comply with NFRC 100. B. Air Leakage, Water Resistance, Structural Test: Comply with ANSI/AAMA 101/I.S.2. C. Forced-Entry Resistance: Comply with ASTM E WINDOW TYPES SELECT FOLLOWING WINDOW TYPES AND RELATED NAIL FIN/MOUNTING STYLE BASED ON PROJECT REQUIREMENTS. DELETE WINDOW TYPES NOT USED. A. Horizontal Slider - [8120T Series, 1-3/8 inch (35 mm) nail fin setback] [8120T Series, block frame (no nail fin)] [8130T Series, 1 inch (25 mm) nail fin setback with stucco key] [8170T Series, 1-5/8 inch (41 mm) Narrow Z-Bar with block frame (no nail fin)] [8140T Series, 2-1/8 inch (54 mm) Wide Z-Bar with block frame (no nail fin)] [8140T Series, 1-3/8 inch (35 mm) nail fin setback, 2 inch (51 mm) long nail fin] [8140T Series, 1-3/8 inch (35 mm) nail fin setback, 2 inch (51 mm) long nail fin with optional [3/4 inch (19 mm) Flat J-channel] [1 inch (25 mm) Contoured J-channel] [2 inch (51 mm) Brickmold-style J-channel]]: 2. Sash: Minimum 1-1/4 inch (32 mm) deep, multi-chambered vinyl profile. Includes vent stops located in fixed sash. 3. Sightlines: Equal for operating and fixed sash. 4. Performance Class: a. 71-1/2" x 59-1/2" and smaller: HS-C40. b. 71-1/2" x 71-1/2" to 71-1/2" x 59-1/2": HS-C35. c. Larger than 71-1/2" x 71-1/2": HS-LC Hardware: a. Nylon rollers with stainless steel axles, extruded vinyl snap-on monorail roller track. b. Dual pull rails. c. SmartTouch direct action locking mechanism. 6. Weatherstripping: Fin Seal Polypropylene pile. B. Double Slider - [8125T Series, 1-3/8 inch (35 mm) nail fin setback] [8125T Series, block frame (no nail fin)] [8125T Series, 1-5/8 inch (41 mm) Narrow Z-Bar with block frame (no nail fin)] [8125T Series, 2-1/8 inch (54 mm) Wide Z-Bar with block frame (no nail fin)] [8125T Series, 1-3/8 inch (35 mm) nail fin setback with optional [3/4 inch (19 mm) Flat J-channel] [1 inch (25 mm) Contoured J-channel] [2 inch (51 mm) Brickmold-style J-channel]]: GUIDE SPEC 8000T-4

4 2. Sash: Minimum 1-3/16 inch (30 mm) deep, multi-chambered vinyl profile. Includes vent stops located in fixed sash. 3. Sightlines: Equal for active and passive sashes. 4. Performance Class: a. 71-1/2" x 59-1/2" and smaller: HS-LC Hardware: a. Nylon rollers with stainless steel axles, extruded vinyl snap-on monorail roller track. b. Single pull rail on active sash. c. SmartTouch direct action locking mechanism. d. Passive sash friction catch. 6. Weatherstripping: Fin seal polypropylene pile. C. Single Hung - [8220T Series, 1-3/8 inch (35 mm) nail fin setback] [8220T Series, block frame (no nail fin)] [8230T Series, 1 inch (25 mm) nail fin setback with stucco key] [8270T Series, 1-5/8 inch (41 mm) Narrow Z-Bar with block frame (no nail fin)] [8240T Series, 2-1/8 inch (54 mm) Wide Z-Bar with block frame (no nail fin)] [8240T Series, 1-3/8 inch (35 mm) nail fin setback, 2 inch (51 mm) long nail fin] [8240T Series, 1-3/8 inch (35 mm) nail fin setback, 2 inch (51 mm) long nail fin with optional [3/4 inch (19 mm) Flat J-channel] [1 inch (25 mm) Contoured J-channel] [2 inch (51 mm) Brickmold-style J-channel]]: 2. Sash: Minimum 1-1/4 inch (32mm) deep, multi-chambered vinyl profile. Includes vent stops located in fixed sash. 3. Sightlines: Equal for operating and fixed sash. 4. Performance Class: a. 56" x 91": H-C Hardware: a. Concealed block and tackle balancer. b. Dual pull rails (sash lifts). c. SmartTouch direct action locking mechanism. 6. Weatherstripping: Fin seal polypropylene pile. D. Double-Hung Tilt - [8225T Series, 1-3/8 inch (35 mm) nail fin setback] [8225T Series, block frame (no nail fin)] [8225T Series, 1-5/8 inch (41 mm) Narrow Z-Bar with block frame (no nail fin)] [8225T Series, 2-1/8 inch (54 mm) Wide Z-Bar with block frame (no nail fin)] [8225T Series, 1-3/8 inch (35 mm) nail fin setback with optional [3/4 inch (19 mm) Flat J-channel] [1 inch (25 mm) Contoured J-channel] [2 inch (51 mm) Brickmold-style J-channel]]: 2. Sash: Minimum 1-3/16 inch (30 mm) deep, multi-chambered vinyl profile. Tilt-in upper and lower sash. Includes vent stops located in fixed sash. 3. Sightlines: Equal for lower and upper sashes. 4. Performance Class: a. 44 x 75 : H-LC35. b. 40 x 63 : H-R Hardware: a. Concealed constant force balancer. b. Dual pull rails (sash lift). c. SmartTouch direct action locking mechanism. d. Upper sash friction catch system. e. Jamb jacks are provided for jamb adjustment for no-fin installation. f. Head expander is provided as an option for no-fin installation. g. Sloped sill adapter is provided as an option for no-fin, sloped sill installation. 6. Weatherstripping: Fin seal polypropylene pile. E. Casement - [8520T Series, 1-3/8 inch (35 mm) nail fin setback] [8520T Series, block frame (no nail fin)] [8530T Series, 1 inch (25 mm) nail fin setback with stucco key] [8570T Series, 1-5/8 inch (41 mm) Narrow Z-Bar with block frame (no nail fin)] [8540T Series, 2-1/8 inch (54 mm) Wide Z-Bar with block frame (no nail fin)] [8540T Series, 1-3/8 inch (35 mm) nail fin setback, 2 inch (51 mm) long nail fin] [8540T Series, 1-3/8 inch (35 mm) nail fin setback, 2 inch (51 mm) long nail fin with optional [3/4 inch (19 mm) Flat J-channel] [1 inch (25 mm) Contoured J-channel] [2 inch (51 mm) Brickmold-style J-channel]]: GUIDE SPEC 8000T-5

5 2. Sash: Minimum 2-5/8 inch (67 mm) deep, multi-chambered vinyl profile. 3. Performance Class: a. 32 x 71 1/2 : C-C55. b. 35 1/2 x 60 : C-C Hardware: a. Dual stainless steel arm rotary operator with standard fold-down nesting handle. b. Single lever, multi-point, locking mechanism. c. Two bar adjustable stainless steel hinge. 5. Weatherstripping: Foam filled bulb (interior), flexible leaf (middle). F. Awning - [8420T Series, 1-3/8 inch (35 mm) nail fin setback] [8420T Series, block frame (no nail fin)] [8430T Series, 1 inch (25 mm) nail fin setback with stucco key] [8470T Series, 1-5/8 inch (41 mm) Narrow Z-Bar with block frame (no nail fin)] [8440T Series, 2-1/8 inch (54 mm) Wide Z-Bar with block frame (no nail fin)] [8440T Series, 1-3/8 inch (35 mm) nail fin setback, 2 inch (51 mm) long nail fin] [8440T Series, 1-3/8 inch (35 mm) nail fin setback, 2 inch (51 mm) long nail fin with optional [3/4 inch (19 mm) Flat J-channel] [1 inch (25 mm) Contoured J-channel] [2 inch (51 mm) Brickmold-style J-channel]]: 2. Sash: Minimum 2-5/8 inch (67 mm) deep, multi-chambered vinyl profile. 3. Performance Class: a. 59-1/2" x 35-1/2" and smaller: AP-C Hardware: a. Stainless steel arm rotary scissor operator with standard fold-down nesting handle. b. Dual lever locking mechanism. c. Two bar stainless steel hinge. 5. Weatherstripping: Foam filled bulb (interior & exterior), flexible leaf (middle). G. Picture and Radius - [8320T Series, 1-3/8 inch (35 mm) nail fin setback] [8360T Series, block frame (no nail fin)] [8330T Series, 1 inch (25 mm) nail fin setback with stucco key] [8370T Series, 1-5/8 inch (41 mm) Narrow Z-Bar with block frame (no nail fin)] [8375T Series, 2-1/8 inch (54 mm) Wide Z-Bar with block frame (no nail fin)] [8340T Series, 1-3/8 inch (35 mm) nail fin setback, 2 inch (51 mm) long nail fin] [8340T Series, 1-3/8 inch (35 mm) nail fin setback, 2 inch (51 mm) long nail fin with optional [3/4 inch (19 mm) Flat J-channel] [1 inch (25 mm) Contoured J-channel] [2 inch (51 mm) Brickmold-style J-channel]]: 2. Sightlines: Equal to Horizontal Slider and Single Hung. 3. Performance Class: a. 8320T, 8330T & 8340T Series, 95-1/2" x 71-1/2" and smaller: F-HC40. b. 8370T & 8375T Series, 95-1/2" x 71-1/2" and smaller: F-HC45. H. Fixed Casement - [8521T Series, 1-3/8 inch (35 mm) nail fin setback] [8521T Series, block frame (no nail fin)] [8531T Series, 1 inch (25 mm) nail fin setback with stucco key] [8571T Series, 1-5/8 inch (41 mm) Narrow Z-Bar with block frame (no nail fin)] [8541T Series, 2-1/8 inch (54 mm) Wide Z-Bar with block frame (no nail fin)] [8541T Series, 1-3/8 inch (35 mm) nail fin setback, 2 inch (51 mm) long nail fin] [8541T Series, 1-3/8 inch (35 mm) nail fin setback, 2 inch (51 mm) long nail fin with optional [3/4 inch (19 mm) Flat J-channel] [1 inch (25 mm) Contoured J-channel] [2 inch (51 mm) Brickmold-style J-channel]]: 2. Sightlines: Equal to Casement Window. 3. Performance Class: 83-1/2 x 71-1/2 and smaller: FW-HC55 I. Fixed Awning - [8421T Series, 1-3/8 inch (35 mm) nail fin setback] [8421T Series, block frame (no nail fin)] [8431T Series, 1 inch (25 mm) nail fin setback with stucco key] [8471T Series, 1-5/8 inch (41 mm) Narrow Z-Bar with block frame (no nail fin)] [8441T Series, 2-1/8 inch (54 mm) Wide Z-Bar with block frame (no nail fin)] [8441T Series, 1-3/8 inch (35 mm) nail fin setback, 2 inch (51 mm) long nail fin] [8441T Series, 1-3/8 inch (35 mm) nail fin setback, 2 inch (51 mm) long nail fin with optional [3/4 inch (19 mm) Flat J-channel] [1 inch (25 mm) Contoured J-channel] [2 inch (51 mm) Brickmold-style J-channel]]: GUIDE SPEC 8000T-6

6 2. Sightlines: Equal to Awning Window. 3. Performance Class: 59-1/2 x 95-1/2 and smaller: AP-C40 J. Replacement Cable Bay Windows - 1 inch (25 mm) nail fin setback: 1. Frame: Minimum 3-1/4" (83 mm) deep, multi-chambered vinyl profile. 2. Unit configuration and window types as shown on drawings, mulled together to form a single window unit. 3. Assembly posts at 45 degrees. 4. Each installation cable rated at 1700 lb. weight capacity /8" think head and seat boards. K. Bay Windows - [1-3/8 inch (35 mm) nail fin setback] [1 inch (25 mm) nail fin setback]: 2. Unit configuration and window types as shown on drawings; mulled together to form single window unit. 3. Assembly posts at 45 degrees. L. Bow Windows - [1-3/8 inch (35 mm) nail fin setback] [1 inch (25 mm) nail fin setback]: 2. Unit configuration and window types as shown on drawings; mulled together to form single window unit. 3. Assembly posts at 13 degrees. M. Garden Window Classic Series, flush mount nail fin: 1. Frame: Minimum 2-13/16 inch (72 mm) deep, multi-chambered vinyl profile. 2. Performance Class: a. 71-1/2" x 59-1/2" and smaller: GH-R Fixed face and top with single-hung sides: mulled together to form single window unit. 4. Projection: 17-1/8 inches (435 mm). N. Jalousie Window - [8820T Series, 1-3/8 inch (35 mm) nail fin setback] [8870T Series, 1-5/8 inch (41 mm) Narrow Z-Bar]: 2. Hardware: a. Lever activated multi-blade tilt hardware. b. 4 blades standard. c. Louvre blade: [1/4" Glass] [Wood] [Cellular PVC] 3. Performance Class: a. 36" x 75 1/2" and smaller: J-R Weatherstripping: Flexible leaf at head and sill GLAZING A. Insulated Glass Units: ASTM E 774, Class A, 7/8 inch (22 mm) thick overall except Garden Window, Double Slider, & Double Hung which are 3/4 inch (19 mm) thick. 1. Glazing Type: [Clear/Clear] [Clear/SunCoat Low-E] [Clear/SunCoat Low-E, argon gas filled] [Clear/SunCoatMAX Low-E] [Clear/SunCoatMAX Low-E, argon gas filled] [Clear/Hardcoat Low-E] [Clear/Hardcoat Low-E, argon gas filled]. WARM EDGE SPACERS ARE NOT AVAILABLE ON SOME UNITS INCLUDING CERTAIN OVERSIZE UNITS, RADIUS AND GABLED UNITS. 2. Spacer Bar: [Warm edge steel spacer] [Aluminum box spacer] [Warm edge foam spacer]. MOST COMMON TYPES OF INSULATED UNITS ARE INCLUDED ABOVE, BUT SEVERAL OTHER TYPES INCLUDING TINTED, REFLECTIVE, HEAT STRENGTHENED, TEMPERED, OBSCURE, WIRE, AND LAMINATED ARE AVAILABLE FOR SPECIAL APPLICATIONS, SELECT DESIRED TYPES FROM MILGARD WEBSITE milgard.com/architects AND SPECIFY IN LIEU OF, OR IN ADDITION, TO THE ABOVE WITH ALL NECESSARY CRITERIA SUCH AS OBSCURE PATTERNS. IF MORE THAN ONE TYPE OF GLAZING IS REQUIRED FOR THE PROJECT, BE CERTAIN THAT TYPE FOR EACH WINDOW IS CLEARLY NOTED ON DRAWINGS OR IN WINDOW SCHEDULE. GUIDE SPEC 8000T-7

7 B. Single Pane Glass: 1. Glazing Type: [Clear] [Solar Bronze] [Solar Gray] [Hardcoat Low-E] [Solar Cool Bronze] [Solar Cool Gray]. OR MOST COMMON TYPES OF SINGLE PANE GLASS ARE INCLUDED ABOVE, BUT SEVERAL OTHER TYPES INCLUDING, REFLECTIVE, HEAT STRENGTHENED, TEMPERED, OBSECURE, WIRE, AND LAMINATED ARE AVAILABLE FOR SPECIAL APPLICATIONS. SELECT DESIRED TYPES FROM MILGARD WEBSITE milgard.com/architects AND SPECIFY IN LIEU OF, OR IN ADDITION, TO THE ABOVE WITH ALL NECESSARY CRITERIA SUCH AS OBSCURE PATTERNS. IF MORE THAN ONE TYPE OF GLAZING IS REQUIRED FOR THE PROJECT, BE CERTAIN THAT TYPE FOR EACH WINDOW IS CLEARLY NOTED ON DRAWINGS OR IN WINDOW SCHEDULE DIVIDED LITE GRIDS VERIFY THAT DESIRED GRID PATTERNS, IF ANY, ARE SHOWN ON THE DRAWING. CERTAIN GRID PATTERNS MAY NOT BE AVAILABLE WITH ONE OR THE OTHER BAR TYPES IN THE FOLLOWING PARAGRAPH- CONSULT MILGARD FOR UNUSUAL DESIGN APPLICATIONS. GRIDS ARE NOT AVAILABLE FOR SINGLE PANE GLASS WINDOWS. A. [5/8 inch (16 mm) wide flat, grids between the glass that are color matched to frame and sash] [1-1/16 inch (27 mm) wide sculptured, grids between the glass that are color matched to frame and sash] [ 7/8 inch (22 mm) Vinyl Simulated Divided Lite (SDL) grids, applied to interior and exterior of insulated glass unit with flat grids within the airspace of the insulated glass unit] 2.07 INSECT SCREENS A. Provide tight-fitting screen for operating sash with hardware to allow easy removal. 1. Screen Cloth: Charcoal colored fiberglass mesh. 2. Frame: a. Cambered formed aluminum with rigid plastic corner keys. b. Roll formed integral pull rail for removal FABRICATION A. Fabricate frames and sash with mitered and fusion welded corners and joints. Trim and finish corners and welds to match adjacent surfaces. B. Provide concealed metal reinforcements in sash frame for attaching lock mechanism. C. Factory inside glaze (except double-hung, double slider and garden window) with snap-on PVC mitred glazing stops matching bevels on the sash and frame. Note: Field glazing is required for large window units (over 40sf (3.72 m 2 )). Insulating glass units shall be reglazable without dismantling sash framing FINISH A. Frame and Sash Color: [White] [Tan]. B. Color match screen frame to window frame and sash color SOURCE QUALITY CONTROL A. Windows inspected in accordance with manufacturer's Quality Control Program as required by AAMA Gold Label certification. GUIDE SPEC 8000T-8

8 PART 3 - EXECUTION 3.01 EXAMINATION A. Examine openings in which windows will be installed. 1. Verify that framing complies with AAMA 2400 ( Mounting Flange Installation ) or AAMA 2410 ( Flush Fin Installation ). 2. Verify that fasteners in framed walls are fully driven and will not interfere with window installation. B. Coordinate with responsible entity to correct unsatisfactory conditions. C. Commencement of work by installer is acceptance of substrate conditions INSTALLATION INSTALLATION INSTRUCTIONS (AAMA 2400) ARE ADEQUATE FOR NORMAL INSTALLATION CONDITIONS IN FRAMED CONSTRUCTION. MASONRY WALLS AND UNUSUAL CONDITIONS MAY REQUIRE ADDITIONAL INFORMATION IN THIS ARTICLE. A. Install windows in framed walls in accordance with AAMA 2400 ( Mounting Flange Installation ) or AAMA 2410 ( Flush Fin Installation ). B. Do not remove temporary labels. C. Install insect screens on operable sash CLEANING A. Reference Section Cleaning and Waste Management. B. Remove temporary labels and retain for Closeout Submittals. C. Clean soiled surfaces and glass using a mild detergent and warm water solution with soft, clean cloths. END OF SECTION This specification was prepared by Milgard Manufacturing, Inc. Comments or suggestions for improvement should be addressed to Milgard at the address in Article 2.01 A. Issue Date: October 31, 2008 GUIDE SPEC 8000T-9