VIESMANN. VITODENS Flue systems for gas condensing boilers 3.8 to kw. Technical guide VITODENS FLUE SYSTEMS

Transcription

1 VIESMNN VITODENS Flue systems for gs ondensing oilers 3.8 to kw Tehnil guide VITODENS FLUE SYSTEMS 5/011

2 Index Index 1. Flue systems Struturl unit... 4 System ertifition Blned flue opertion Open flue opertion Flue gs high limit sfety ut-out Lightning protetion CE ertifition for the PPs flue systems (rigid nd flexile) for the Vitodens Flue instlltion options for lned flue opertion... 8 Inside the living spe (oupied res) with one or more full floors ove... 8 Inside the living spe (oupied re) immeditely underneth the roof or with only ttis ove (rted output 50 kw)... 9 Severl Vitodens in the living spe or in oupied rooms (living spe - rted output 50 kw) Flue instlltion options for open flue opertion... 9 Inside the instlltion lotion (non-living spe) with one or more full floors ove (ompulsory for the Vitodens 00-W from 60 kw) Speil version: open flue opertion nd instlled in the living spe (oupied re) with omustion ir interonnetion (rted output 35 kw) Flue gs heder for severl Vitodens 00-W, -W nd -F positive pressure 11 Flue gs heder for severl Vitodens negtive pressure Design nd sizing informtion for onnetion on the flue gs side.1 Plsti (PPs) lned flue system for routing through shft lned flue opertion (type C 63x to TRGI 008) Internl shft dimensions to DIN V Flue, system size 60, 80 nd 100 (omponents) (type C 63x ording to TRGI 008) 13 Vitodens in onjuntion with solid fuel oilers Flue, flexile, system size 60, 80 nd 100 (omponents) (type C 63x ording to TRGI 008) Plsti (PPs) lned flue system for vertil routing through pithed or flt roof (type C 33x to TRGI 008) For vertil roof outlets when the Vitodens is instlled in ttis Vertil flt roof outlet Plsti (PPs) lned flue system for externl wll onnetion (type C 13x to TRGI 008) Mx. totl length of the flue pipe Plsti (PPs) lned flue system for routing over externl wlls (type C 53x to TRGI 008) Plsti (PPs) lned flue system for routing through lightweight shft... 1 "UNIFIX" shft profiles offered y Skoerne (mde from erted onrete)... "SKOBIFIXnno" nd "SKOBIFIXXs 30" shft profiles offered y Skoerne (mde from fomed ermis)... nhoring for roof outlets with shft profiles... Promt shft profiles... 3 Roof outlet for shfts with Promt profiles Plsti (PPs) lned flue system for routing multiple pipes through shft... 4 Lyout exmples Plsti (PPs) lned flue system (onnetion line) for onneting multiple flues to single room seled lned flue system... 5 Room seled lned flue system, negtive pressure (type C 43x to TRGI 008)... 6 Room seled lned flue system, positive pressure multiple onnetions with the Vitodens 00-W, -W nd -F up to 6 kw (type C 43x to TRGI 008) Plsti (PPs) flue pipe for routing through shft with open flue opertion (type B ording to TRGI 008)... 9 Internl shft dimensions... 9 Flue, system size 60, 80 nd 100 (omponents) (type B 3 /B 33 ording to TRGI 008) Flue, flexile, system size 60, 80 nd 100 (omponents) (type B 3 to TRGI 008).. 31 Speil version: open flue opertion with omustion ir interonnetion for the Vitodens up to 35 kw (type B 33 to TRGI 008)... 3 Connetion to moisture-resistnt himney (MR himney negtive pressure) with plsti (PPs) flue pipe (type B 3x, ording to TRGI 008) Multi oiler systems with flue systems operting with positive pressure (open flue opertion) Vitodens 00-W, 19 to 105 kw, Vitodens -W nd -F Multi oiler systems with flue systems - negtive pressure Flue system omponents 3.1 Blned flue system omponents... 4 VIESMNN VITODENS

3 Index (ont.) 3. Components for routing flue over n externl wll Single pipe system omponents Components for multiple onnetions to room seled lned flue system positive pressure for the Vitodens 00-W, -W nd -F, 19 to 6 kw Components of the flexile single pipe system for flexile flue Components for multi oiler systems Roof elements Keyword index VITODENS VIESMNN 3

4 Flue systems 1 The following requirements regrding design nd instlltion pply to flue systems for ondensing omustion equipment: Prior to strting work on the flue system, your heting ontrtor should onfer with the flue gs inspetor responsile [where pplile]. Gs omustion equipment must e onneted to the domesti himney stk on the sme floor where it is instlled (no trnsition through seprting eilings). Here, differentition is required s to whether the ondensing oiler should e sited in the living spe (oupied rooms) or outside the living spe (instlltion room). Siting the Vitodens in the living spe is fesile, sujet to the flue inside the living spe eing routed inside protetive pipe nd eing surrounded y ventiltion ir (lned flue system, lned flue opertion). s speil se, n instlltion inside the living spe is lso fesile for open flue opertion, provided onnetion piee with seondry ventiltion up to the shft (opertion with interonneted room ir supply) is provided (see pge 3). Struturl unit The forementioned onditions re generlly met when CE-designted flue systems (essories) re used together with the Vitodens. The following Viessmnn lned flue systems for lned flue opertion re tested to DVGW nd re CE-designted s single struturl unit with the Vitodens: Vertil roof outlet Externl wll onnetion Horizontl roof outlet Externl routing through oxil pipe dvntges of single struturl units: No lulted funtion verifition for flue pipes to DIN EN is required for individul ses Simplified visul inspetion y the lol flue gs inspetor every two yers No dditionl pprovl ertifite y the flue pipe mnufturer is required In non-living spe, the flue my lso e instlled inside the instlltion room without seondry ventiltion. However, the instlltion room would then require n dequtely sized vent to the outside (. to TRGI 008). Rted output up to 50 kw: 150 m or 75 m Rted output ove 50 kw (e.g. Vitodens 00-W, from 60 kw, or multi oiler systems): 150 m plus m for eh kw ove 50 kw The plin flue must e type pproved y the Deutshes Institut für Butehnik (DIBt) [Germny] (open flue opertion). The flue ville s n essory is CE-designted nd pproved to DIN EN System ertifition System ertifition to DVGW-VP 113 nd EC Gs pplines Diretive 009/14/EC in onjuntion with PPs flue pipes offered y Skoerne Vitodens 00-W Vitodens -F Vitodens -W Vitodens 4-F Vitodens 300-W Vitodens 333-F Vitodens 343-F Vitosolr 00-F CE-0085BR043 CE-0085BU0051 CE-0085BR043 CE-0085BU0051 CE-0085BR0433 CE-0085BU005 CE-0085BU005 CE-0085CM Blned flue opertion The seled omustion hmer of the Vitodens gs ondensing oilers enles their use in lned flue opertion. These oilers re tegorised s C 13x, C 33x, C 43x, C 53x, C 63x or C 83x ording to TRGI 008. ommon pprovl for the Vitodens nd lned flue system pplies to this type of equipment. The tightness test (overpressure test) y the flue gs inspetor during ommissioning s well s the verifition of the "Generl Building Regultions pprovl" y the DIBt my e omitted for this type of onstrution. Every pproved flue system n e used for type C 63x. This flue system is not tested together with the oilers. Mintin the dimensions speified on pges 11 to 0. The omustion ir is supplied nd the flue gs extrted through one onentri oxil pipe (lned flue system). The omustion ir is supplied through the nnulr gp etween the externl luminium ventiltion ir pipe nd the flue pipe. Flue gses re extrted through the internl plsti pipe (PPs). For lned flue systems tested together with the wll mounted gs oiler, there is no requirement for tightness test during ommissioning y the flue gs inspetor. We reommend tht your heting engineer rries out simple tightness test during the ommissioning of your system. For this it would e suffiient to hek the CO onentrtion in the omustion ir t the nnulr gp of the lned flue pipe. The flue is onsidered suffiiently gs-tight if the CO onentrtion in the omustion ir is no higher thn 0. %, or if the O onentrtion is t lest 0.6 %. Chek the flue system for tightness y pressure testing if higher CO or lower O vlues re estlished. In onjuntion with the onentri oxil pipe (lned flue system), the surfe temperture of the Vitodens or tht of the lned flue system will never exeed 85 ºC. Therefore, lernes to omustile omponents ording to TRGI re not required. For oiler types C 63x nd C 43x, the DIBt-pproved flue pipes from Viessmnn or lterntive DIBt-pproved flue pipes y other mnufturers my lso e used. Use ondenste trp ove the oiler flue onnetion if n luminium flue pipe is instlled. Instll the onneting lines with fll of t lest 3 to the oiler. The lned flue system is CE-designted nd pproved to DIN EN (see pge 6). The oiler sing retes system tht is seled ginst its surroundings. ny leks used y esping flue gs re returned vi the omustion ir, therey preventing flue gs from entering the living spe. 4 VIESMNN VITODENS

5 Flue systems (ont.) When instlling the Vitodens in sement or on lower floor, n existing himney or shft of dequte size my e used for the lned flue opertion (type C 43x nd C 63x ). ording to TRGI 008, flues tht ridge severl floors must e routed inside shft with fire rting of t lest 90 minutes, nd for uildings in tegories 1 nd, fire rting of t lest 30 minutes. The flue gs/ventiltion ir is routed in lned flue up to the himney or shft. The flue pipe is routed inside the himney or shft to ove roof level. Where no suitle shft is ville, the flue my e routed to the roof through retrofitted shft. For this shft, Building Regultions test ertifite or CE designtion orresponding to the design of the shft is required. In ddition, the shft must hve fire rting of L30 or L Open flue opertion (Type B 3 nd B 33 ) Flue gs is routed through single wll plsti pipes (PPs). The flue system is CE-designted nd pproved to DIN EN (see pge 6). The omustion ir supply is ensured vi the nnulr gp etween the flue pipe nd the ventiltion ir inlet on the oiler flue onnetion of the Vitodens. 1.4 Flue gs high limit sfety ut-out ording to CE designtion to DIN EN 14471, the plsti flue pipe (PPs) n e utilised up to mximum flue gs temperture of 10 ºC (type B). Mesures inside the equipment ensure tht the flue gs temperture of 90 ºC will never e exeeded. flue gs high limit sfety ut-out is therefore not required. 1.5 Lightning protetion If lightning protetion system is instlled, ny metlli flue system should e inluded in the lightning protetion sheme. VITODENS VIESMNN 5

6 Flue systems (ont.) 1.6 CE ertifition for the PPs flue systems (rigid nd flexile) for the Vitodens 1 6 VIESMNN VITODENS

7 Flue systems (ont.) 1 VITODENS VIESMNN 7

8 Flue systems (ont.) Flue instlltion options for lned flue opertion (No seprte ventiltion nd extrt ir vents required) Inside the living spe (oupied res) with one or more full floors ove Routing through shft (type C 63x, to TRGI 008) The oiler drws omustion ir from the tmosphere through the nnulr gp inside the shft (himney) nd expels the flue gs vi the flue pipe ove roof level. For ondensing oilers > 50 kw, the instlltion lotion must e ventilted even for lned flue opertion. The shft is not prt of the stndrd delivery. For detiled desription, see from pge 11. Retrofitted shfts Instlltion in retrofitted shft with Building Regultion pprovl onsisting of individul shft elements (e.g. s supplied y SIMO, Wienererger or Skoerne) or inluding minerl profiles (e.g. from Promtet). For detiled desription of shfts, see pge 1. Flue gs B Ventiltion ir Flue gs B Ventiltion ir Externl wll onnetion Only for uildings with proteted rights (Type C 13x, to TRGI 008) (permissile up to rted output of 11 kw for entrl heting or 8 kw for DHW heting) ording to the LndesFeuVo, issue 1999 [Germny], n externl wll onnetion is only permissile in individul ses, where routing the flue gs y other mens is not pproprite for tehnil or eonomil resons. The oiler drws omustion ir from outside vi onentri oxil pipe mounted to the externl wll nd expels flue gs vi the outside wll to tmosphere. For detiled desription, see pge 19. Horizontl roof outlet (Type C 13x, to TRGI 008) (no limittion of the rted output) The oiler drws omustion ir from outside t the roof dormer vi onentri oxil pipe nd expels flue gs t the dormer to tmosphere. Routing over n externl wll (Type C 53x, to TRGI 008) The oiler drws omustion ir from the tmosphere vi horizontl, onentri oxil pipe on the externl wll nd expels flue gs to the tmosphere vi the roof. In its vertil setion, the outer pipe of the onentri oxil pipe ts s therml insultion thnks to its stti lyer of ir. The omustion ir is supplied vi the lned flue ir inlet. For detiled desription, see pge 0. Flue gs B Ventiltion ir 8 VIESMNN VITODENS

9 Flue systems (ont.) Inside the living spe (oupied re) immeditely underneth the roof or with only ttis ove (rted output 50 kw) Vertil outlet, if no shft is ville (Type C 33x, to TRGI 008) (vrious options) 1 Diret, vertil roof outlet through pithed roof Indiret, vertil roof outlet through pithed roof with protetive pipe inside the tti spe (not onstruted s room) or fire protetion rikwork (onstruted s room) 3 Diret, vertil roof outlet through flt roof The oiler drws omustion ir from the tmosphere nd expels flue gs to the tmosphere vi onentri oxil pipe through the roof. For detiled desription, see pge Flue gs B Ventiltion ir C Pipe to protet ginst mehnil dmge Severl Vitodens in the living spe or in oupied rooms (living spe - rted output 50 kw) Instlltion on different floors (Type C 43x, to TRGI 008) Opertion with negtive pressure: Room seled lned flue system required. Opertion with positive pressure: Blned flue system for severl onnetions. Severl het soures drw omustion ir from the outside through the nnulr gp of the room seled lned flue system nd expel flue gs vi the roof to tmosphere through moisture-resistnt internl pipe. For detiled desription, see pges 5 nd 6. Flue gs B Ventiltion ir 1.8 Flue instlltion options for open flue opertion (Seprte ventiltion ir vent with 150 m or 75 m ross-setion required) VITODENS VIESMNN 9

10 Flue systems (ont.) Inside the instlltion lotion (non-living spe) with one or more full floors ove (ompulsory for the Vitodens 00-W from 60 kw) 1 Routing through shft (Type B 3, to TRGI 008) The oiler drws omustion ir from the instlltion room nd expels flue gs through the flue vi the roof (lned flow). For detiled desription, see pge 9. Flue gs B Seondry ventiltion C Ventiltion ir Connetion to moisture-resistnt himney (MR himney) (Type B 3, to TRGI 008) The oiler drws omustion ir from the instlltion room nd routes flue gs through the moisture-resistnt himney vi the roof. For detiled desription, see pge 33. Flue gs B Seondry ventiltion C Ventiltion ir Speil version: open flue opertion nd instlled in the living spe (oupied re) with omustion ir interonnetion (rted output 35 kw) Routing through shft or Connetion to moisture-resistnt himney (Type B 33, to TRGI 008) The oiler drws omustion ir from the living spe vi oxil pipe with ventiltion ir vents upstrem of the shft inlet nd expels the flue gs either vi flue pipe or vi moisture-resistnt himney through the roof (omustion ir supply vi interonneted rooms ording to TRGI). For detiled desription, see pge 3. Flue gs B Ventiltion ir C Seondry ventiltion D Door E Interonneted ir supply 10 VIESMNN VITODENS

11 Flue systems (ont.) Flue gs heder for severl Vitodens 00-W, -W nd -F positive pressure Type B 3, to TRGI 008 Severl oilers inside the sme room drw omustion ir from outside vi vents nd expel the flue gs through ommon flue pipe vi the roof to the tmosphere. For detiled desription, see pge 34. Flue gs B Seondry ventiltion C Ventiltion ir Flue gs heder for severl Vitodens negtive pressure Type B 3, to TRGI 008 Severl oilers inside the sme room drw omustion ir from outside vi vents nd expel the flue gs through ommon flue pipe vi the roof to the tmosphere. For detiled desription, see pge 4. Flue gs B Ventiltion ir Design nd sizing informtion for onnetion on the flue gs side ll detils regrding length nd ross-setion in the following tles re only vlid in onnetion with the lned flue omponents offered in the Viessmnn prielist..1 Plsti (PPs) lned flue system for routing through shft lned flue opertion (type C 63x to TRGI 008) For lned flue opertion, oxil flue pipe (internl pipe for flue gs, externl pipe for omustion ir) is required s onnetion piee etween the Vitodens nd the shft. Vitodens 00-W to 35 kw, Vitodens -F, Vitodens -W, Vitodens 4-F, Vitodens 300-W nd 333-F, Vitodens 343-F nd Vitosolr 00-F Internl dimeter Ø in mm Flue pipe Ventiltion ir pipe Vitodens 00-W, 45 to 60 kw Vitodens 00-W, 80 to 105 kw The onnetion piee is fitted to the oiler flue onnetion nd must provide n inspetion port. Note Gs ondensing oilers with totl rted output greter thn 50 kw my only e instlled in rooms tht provide ir vents leding outside, see pge 9. For instlltion through shfts or hnnels with longitudinl ventiltion meeting the requirements for himney stks to DIN V , or with fire rting of 90 minutes (L90), or fire rting of 30 minutes (L30) for uildings in tegories 1 nd (mx. storeys). Prior to instlltion, the flue gs inspetor should hek tht the shft to e used is suitle nd pproved for this purpose. VITODENS VIESMNN 11

12 Design nd sizing informtion for onnetion on the flue gs side (ont.) Shfts tht were previously onneted to oil or solid fuel oilers must e thoroughly lened y himney sweep. Loose deposits omprising sulphur nd soot must not remin on the inside of the himney. Running lned flue pipe through the shft is then not required. If thorough lening is impossile, if hloride deposits re present or if the shft is silted up, seprte lned flue n e used inside the shft. Close off nd sel ny other onnetion pertures with pproprite mterils. This does not pply to ny lening or test pertures tht re provided with himney lening overs nd to whih n pproprite test mrk hs een ffixed. Chek prior to instlltion whether the shft runs stright from top to ottom or if it is offset (hek with mirrors). If the himney is offset, we reommend the instlltion of flexile flue pipe (see pge 16). Inside the instlltion lotion, t lest one inspetion port must e provided in the flue system for heking nd lening s well s for heking the pressure (if required). If the flue pipe is inessile from the roof, seond inspetion port must e provided in the tti ehind the himney lening hth. For further informtion, see FeuVo [Germny] Provide n inspetion port t the se of the shft for heking the seondry ventiltion. Sfegurd the drining of the ondenste from the flue pipe to the oiler with fll of t lest 3º. The flue system must e routed to ove the roof (protrusion ove the roof ording to lol regultions). lterntive CE-designted flue pipes my e used, for exmple, if lrger flue pipe dimeter is required, i.e. euse of greter flue lengths. The funtion verifition to EN should then e provided y the respetive flue mnufturer. If flue pipes other thn those offered s essories (whih re pproved with the Vitodens s single tehnil unit) re used, the flue system must e heked for tightness y the flue gs inspetor prior to ommissioning. This my e rried out, in ordne with the flue system pprovl ertifite, y mesuring the CO or O vlue inside the nnulr gp. If this test results in CO ontent of more thn 0. % or n O ontent elow 0.6 %, hek the flue system. Internl shft dimensions to DIN V Note ording to the pprovl ertifite, internl shft dimensions smller thn those shown in the tles my lso e used for lned flue opertion, if this is indited y the funtion verifition to DIN EN Minimum internl shft dimensions System size Externl dimeter; Minimum internl shft dimension femle onnetion squre or retngulr round (short side) Ø mm mm Ø mm (flexile) (flexile) (flexile) Redued internl shft dimensions System size Externl dimeter; Redued internl shft dimension femle onnetion squre or retngulr round (short side) Ø mm mm Ø mm VIESMNN VITODENS

13 Design nd sizing informtion for onnetion on the flue gs side (ont.) Flue, system size 60, 80 nd 100 (omponents) (type C 63x ording to TRGI 008) C D Ventiltion ir B Flue gs C Inspetion port D Connetion piee C B C System size Ø mm 1 Boiler flue onnetion (prt of the stndrd oiler delivery) Stndrd shft set (PPs, rigid) Comprising: Support end Support ril Shft over Spers (3 pe, mx. distne 5 m) or Stndrd shft pk (metl/pps, rigid) for twin drught himneys; one drught for solid fuel oilers Comprising: Support end Support ril Shft over (metl) Terminl pipe (stinless steel) Spers (3 pe, mx. distne 5 m) Spers (3 pe, mx. distne 5 m) Flue pipe 1.95 m long ( 1.95 m = 3.9 m) 1.95 m long (1 pe) m long (1 pe) m long (1 pe) Flue end (for use in orelled himneys) º ( pe) 15º ( pe) 4 Inspetion piee, stright (1 pe) Blned flue inspetion piee, stright (1 pe) 6 Blned flue wll ezel Blned flue pipe m long 0.5 m long 8 Blned flue end º (1 pe) 45º ( pe) or Blned flue inspetion tee º (1 pe) Blned flue inspetion end º (1 pe) 9 Blned flue slide oupling Fixing lmp, white (1 pe) Stinless steel extension, 380 mm long for shft over, stndrd shft pk (metl/pps, rigid) Blned flue dptor Ø 80/15 mm to Ø 60/100 mm Ø 60/100 mm to Ø 80/15 mm Ø 80/15 mm to Ø 100/150 mm Mx. totl length of the flue up to the oiler flue onnetion Vitodens 00-W, -F, -W, 4-F nd Vitosolr 00-F Rted output rnge kw mx. length - system size 60 m mx. length - system size 80 m 5 *1 5 *1 5 * mx. length - system size 100 m 5 *1 0 *1 0 0 *1 lterntive system size: order lned flue dptor seprtely. VITODENS VIESMNN 13

14 Design nd sizing informtion for onnetion on the flue gs side (ont.) Vitodens 300-W, 333-F nd 343-F Rted output rnge kw mx. length - system size 60 m mx. length - system size 80 m 17 *1 17 *1 0 *1 15 *1 The following omponents re tken into onsidertion for the mximum flue lengths: Blned flue onnetion pipe D 0.5 m long. 1 lned flue end 87º nd 1 flue end 87º or lned flue ends 45º nd 1 flue end 45º Sutrt other ends, tees nd stright lengths from the mximum length using the following vlues: Blned flue onnetion pipe 0.5 m long: 1 m Blned flue onnetion pipe 1 m long: m Blned flue ends 45º: 0.5 m Blned flue ends 87º: 1 m Blned flue inspetion tee: 0.5 m Note Oserve the speifitions regrding internl shft dimensions (see pge 1). Vitodens in onjuntion with solid fuel oilers Routing the flue pipe in twin drught shft. The plsti flue pipe n e routed together with the flue pipe from solid fuel oiler inside twin-flue himney. The following onditions re met: When using plsti shft over: The himney for solid fuel oilers must protrude t lest 1000 mm ove the Vitodens flue. For the himney extension, only use omponents tht re resistnt to soot fires. Open flue opertion or the ventiltion ir is not supplied through the shft For fire sfety resons, the terminls of flmmle flue pipes should e mde from non-omustile mterils. For flues of stndrd flmmility, they should e loted up to pprox. 400 mm elow the shft terminl, nd for flues of low flmmility, pprox. 300 mm elow the shft terminl B B C C 300/400 E D F E D F Metl shft over B End piee mde from non-omustile mteril C Seondry ventiltion D Vitodens flue E Chimney for solid fuel oilers F Minimum lerne to DIN V 18160, redued minimum lerne or mximum lerne to DIN EN (see pge 1) Blned flue opertion the ventiltion ir is supplied through the shft Design the lned flue terminls so tht flue gs will not e drwn into the ir shft in dngerous volumes nd so tht pressure flututions due to wind influene ffet the lned flue system s evenly s possile. *1 lterntive system size: order lned flue dptor seprtely. Chimney extension mde from soot-resistnt nd fire-resistnt mteril B Plsti shft over C Ventiltion/seondry ventiltion D Vitodens flue E Chimney for solid fuel oilers F Minimum lerne to DIN V 18160, redued minimum lerne or mximum lerne to DIN EN (see pge 1) When using metl shft over: The himney for solid fuel oilers must protrude t lest x Ø D ove the Vitodens flue. For the himney extension, only use omponents tht re resistnt to soot fires. 14 VIESMNN VITODENS

15 Design nd sizing informtion for onnetion on the flue gs side (ont.) Ø D B x D The metl terminl pipe nd shft over re prt of the stndrd shft pk (metl/pps). The stndrd shft pk (metl/pps) is ville s n essory. C E D F Chimney extension mde from soot-resistnt nd fire-resistnt mteril B Metl shft over C Ventiltion/seondry ventiltion D Vitodens flue (rigid or flexile) E Chimney for solid fuel oilers F Minimum lerne to DIN V 18160, redued minimum lerne or mximum lerne to DIN EN (see pge 1) When using ommon downdrught plte: The flue end piee nd the shft over must e mde from nonomustile mteril (e.g. metl). x D Ø D B C D F E G Chimney extension mde from soot-resistnt nd fire-resistnt mteril B End piee mde from non-omustile mteril C Shft over (on-site) D Ventiltion/seondry ventiltion E Vitodens flue F Chimney for solid fuel oilers G Minimum lerne to DIN V 18160, redued minimum lerne or mximum lerne to DIN EN (see pge 1) VITODENS VIESMNN 15

16 Design nd sizing informtion for onnetion on the flue gs side (ont.) Flue, flexile, system size 60, 80 nd 100 (omponents) (type C 63x ording to TRGI 008) 1 9 qp D C Ventiltion ir B Flue gs C Inspetion port D Connetion piee C B C Note The flexile flue pipe must only e routed vertilly. System size Ø mm 1 Boiler flue onnetion (prt of the stndrd oiler delivery) Stndrd shft pk (PPs, flexile) Comprising: Support end Support ril Shft over Spers (5 pe, mx. distne m) Stndrd shft set (metl/pps, flexile) for twin flue himneys; one for solid fuel oilers Comprising: Support end Support ril Shft over (metl) Terminl pipe (stinless steel) Spers (5 pe, mx. distne m) Spers (5 pe, mx. distne m) Flue pipe, flexile, s 1.5 or m roll 4 Connetion piee for onneting residul lengths of the flexile flue 5 Inspetion piee, stright for instlltion into the flexile flue pipe Pipe lowering tthment with m rope 6 Blned flue inspetion piee, stright (1 pe) 7 Blned flue wll ezel Blned flue pipe m long 0.5 m long 9 Blned flue end º (1 pe) 45º ( pe) or Blned flue inspetion tee º (1 pe) Blned flue inspetion end º (1 pe) qp Blned flue slide oupling Fixing lmp, white (1 pe) Stinless steel extension, 380 mm long for shft over, stndrd shft pk (metl/pps, flexile) Blned flue dptor Ø 80/15 mm to Ø 60/100 mm Ø 60/100 mm to Ø 80/15 mm Ø 80/15 mm to Ø 70/110 mm 80 Ø 80/15 mm to Ø 100/150 mm Mx. totl flue length up to the oiler flue onnetion with flexile flue pipe Vitodens 00-W, -F, -W, 4-F nd Vitosolr 00-F Rted output rnge kw mx. length - system size 60 m 18 mx. length - system size 80 m 5 *1 5 *1 5 * mx. length - system size 100 m *1 17 *1 0 0 *1 lterntive system size: order lned flue dptor seprtely. 16 VIESMNN VITODENS

17 Design nd sizing informtion for onnetion on the flue gs side (ont.) Vitodens 300-W, 333-F nd 343-F Rted output rnge kw mx. length - system size 60 m mx. length - system size 80 m 16 *1 16 *1 18 *1 13 *1 The following omponents re tken into onsidertion for the mximum flue lengths: Blned flue onnetion pipe D 0.5 m long. 1 lned flue end 87º nd 1 flue end 87º or lned flue ends 45º nd 1 flue end 45º Sutrt other ends, tees nd stright lengths from the mximum length using the following vlues: Blned flue onnetion pipe 0.5 m long: 1 m Blned flue onnetion pipe 1 m long: m Blned flue ends 45º: 0.5 m Blned flue ends 87º: 1 m Blned flue inspetion tee: 0.5 m Note Oserve the speifitions regrding internl shft dimensions (see pge 1).. Plsti (PPs) lned flue system for vertil routing through pithed or flt roof (type C 33x to TRGI 008) For vertil roof outlets when the Vitodens is instlled in ttis The roof outlet my only e used, where the eiling of the oupied room lso forms prt of the roof or only the roof struture is loted ove the eiling (pithed tti). Note Instll ondensing oilers with n output > 50 kw in seprte nd ventilted instlltion lotion (ording to FeuVo [Germny]) (Vitodens 00-W from 60 kw). When the lned flue system is routed through roof spes tht re not used s ommodtion, run the lned flue pipe through n dditionl metl pipe s protetion ginst mehnil dmge (TRGI 008). It my lso e routed ehind jm wll or solid wll of n tti uilt s ommodtion, if the fire protetion lss of the jm wll orresponds to tht of the eiling (e.g. B30). Minimum lernes to omustile mterils inside the instlltion lotion or in onnetion with the roof outlet re not required. s prt of the CE pprovl test, it ws verified tht no surfe tempertures on the Vitodens or its lned flue system will exeed 85 ºC. Vitodens 00-W to 35 kw, Vitodens -F, Vitodens -W, Vitodens 4-F, Vitodens 300-W nd 333-F, Vitodens 343-F nd Vitosolr 00-F Internl dimeter Ø in mm Flue pipe Ventiltion ir pipe Vitodens 00-W, 45 to 60 kw Vitodens 00-W, 80 to 105 kw Instll n inspetion port for heking nd lening the flue pipe inside the instlltion room. The vertil roof outlet hs een tested nd CE-designted s onentri lned flue system s one struturl unit with the Vitodens ondensing oiler. funtion verifition ording to EN is not required. Vertil flt roof outlet Integrte the flt roof ollr into the roof skin ording to the flt roof guidelines (see pge 58). Push the roof outlet into the roof from ove nd position it on the flt roof ollr. Note The eiling opening should hve dimeter of t lest the speified size: System size Ø 60 mm: 105 mm System size Ø 80 mm: 130 mm System size Ø 100 mm: 160 mm Seure the roof outlet on site with lmp fter the instlltion hs een ompleted. Mintin minimum lernes of 1.5 m towrds eh other nd other omponents in ordne with FeuVo [Germny], when instlling severl vertil roof outlets djent to eh other. Note Seprte extensions re ville (see tle) if the length of 400 mm ove the roof line nd vertil to the roof surfe is insuffiient euse of speifi requirements. pprovl with the flue system is ensured. *1 lterntive system size: order lned flue dptor seprtely. VITODENS VIESMNN 17

18 Design nd sizing informtion for onnetion on the flue gs side (ont.) 3 C 1 B Ventiltion ir B Flue gs C Inspetion port C 1 B 4 C 5 4 System size Ø mm 1 Boiler flue onnetion (prt of the stndrd oiler delivery) Blned flue roof outlet with fixing lmp Colour: lk or Colour: terrott ove roof extension with lmp (re on site) Colour: lk 0.5 m long m long, with ring lmp Colour: terrott 0.5 m long m long, with ring lmp Universl roof tile For Romn tiles, pntiles, plin tiles, slte nd other types of roof over Colour: lk or terrott or Flt roof ollr or Pipe outlet for Klöer roof tiles Colour: lk or terrott (provide the orresponding Klöer tile on site to mth the roof outlet seleted for the prtiulr type of roof) 4 Blned flue inspetion piee, stright (1 pe) 5 Blned flue slide oupling Universl over plte Blned flue end º (1 pe) 45º ( pe) Blned flue pipe m long 0.5 m long Fixing lmp, white (1 pe) Blned flue dptor Ø 80/15 mm to Ø 60/100 mm Ø 60/100 mm to Ø 80/15 mm Ø 80/15 mm to Ø 100/150 mm Mx. totl length of the flue pipe Vitodens 00-W, -F, -W, 4-F nd Vitosolr 00-F Rted output rnge kw mx. length - system size 60 m mx. length - system size 80 m 13 *1 13 *1 11 * mx. length - system size 100 m 13 *1 9 * min. mm Vitodens 300-W, 333-F nd 343-F Rted output rnge kw mx. length - system size 60 m mx. length - system size 80 m 13 *1 13 *1 13 *1 11 *1 min. mm x 87º lned flue ends re tken into onsidertion for the mximum flue lengths. *1 lterntive system size: order lned flue dptor seprtely. Sutrt other ends, tees nd stright lengths from the mximum length using the following vlues: Blned flue ends 45º: 0.5 m Blned flue ends 87º: 1 m Blned flue inspetion tee: 0.5 m 18 VIESMNN VITODENS

19 Design nd sizing informtion for onnetion on the flue gs side (ont.).3 Plsti (PPs) lned flue system for externl wll onnetion (type C 13x to TRGI 008) s prt of the CE pprovl test, it ws verified tht no surfe tempertures on the Vitodens or the lned flue system will exeed 85 ºC. Oserve the implementtion informtion to TRGI 008, in prtiulr the rrngement/position of the wll outlet. Instll the onnetion line with fll of t lest 3 towrds the oiler. Instll n inspetion port for heking nd lening the flue pipe. The externl wll onnetion hs een tested nd CE-designted s onentri lned flue system s one struturl unit with the Vitodens ondensing oiler. funtion verifition ording to EN is not required. Vitodens 00-W to 35 kw, Vitodens -F, Vitodens -W, Vitodens 4-F, Vitodens 300-W, Vitodens 333-F, Vitodens 343-F nd Vitosolr 00-F Internl dimeter Ø in mm Flue pipe Ventiltion ir pipe Vitodens 00-W, 45 to 60 kw Vitodens 00-W, 80 to 105 kw Ventiltion ir B Flue gs C Inspetion port C 7 B System size Ø mm 1 Boiler flue onnetion (prt of the stndrd oiler delivery) Blned flue externl wll onnetion (inl. wll ezels) 3 Blned flue pipe m long 0.5 m long 4 Blned flue end º (1 pe) 45º ( pe) or Blned flue inspetion end, 87 ( pe) 5 Blned flue inspetion piee, stright (1 pe) 6 Blned flue slide oupling Protetive grille required, if the omustion ir inlet nd flue outlet lie t height of up to m ove ground level in res of puli or privte trffi Fixing lmp, white (1 pe) Blned flue dptor Ø 80/15 mm to Ø 60/100 mm Ø 60/100 mm to Ø 80/15 mm Mx. totl length of the flue pipe Vitodens 00-W, -F, -W, 4-F nd Vitosolr 00-F Rted output rnge kw mx. length - system size 60 m mx. length - system size 80 m 13 *1 13 *1 11 * mx. length - system size 100 m 13 *1 13 * Vitodens 300-W, 333-F nd 343-F Rted output rnge kw mx. length - system size 60 m mx. length - system size 80 m 13 *1 13 *1 13 *1 11 *1 x 87º lned flue ends re tken into onsidertion for the mximum flue lengths. *1 lterntive system size: order lned flue dptor seprtely. Sutrt other ends, tees nd stright lengths from the mximum length using the following vlues: Blned flue ends 45º: 0.5 m Blned flue ends 87º: 1 m Blned flue inspetion tee: 0.5 m VITODENS VIESMNN 19

20 Design nd sizing informtion for onnetion on the flue gs side (ont.).4 Plsti (PPs) lned flue system for routing over externl wlls (type C 53x to TRGI 008) The Vitodens my lso e onneted, without shft, to flue pipe routed over n externl wll. The omustion ir is drwn in vi the ir inlet piee. The vertil externl pipe ts s protetion nd the stti ir inside ts s therml insultion. Vitodens 00-W to 35 kw, Vitodens -F, Vitodens -W, Vitodens 4-F, Vitodens 300-W, Vitodens 333-F, Vitodens 343-F nd Vitosolr 00-F Internl dimeter Ø in mm Flue pipe Ventiltion ir pipe Vitodens 00-W, 45 to 60 kw Vitodens 00-W, 80 to 105 kw Where the flue is routed over n externl wll, it hs een tested nd CE-designted s onentri lned flue tht forms single struturl unit with the Vitodens ondensing oiler. funtion verifition ording to EN is not required..0 m.5 m Flue gs B Ventiltion ir C Inspetion port D Elow in the flue routed over n externl wll, see pge 45 0 VIESMNN VITODENS

21 Design nd sizing informtion for onnetion on the flue gs side (ont.) System size Ø mm 1 Boiler flue onnetion (prt of the stndrd oiler delivery) Blned flue inspetion tee º (1 pe) Blned flue inspetion end, º (1 pe) or Blned flue inspetion piee, stright (1 pe) nd Blned flue end 87º (1 pe) Blned flue slide oupling Blned flue pipe m long (1 pe) 1 m long (1 pe) 0.5 m long (1 pe) 5 Wll ezel Fixing lmp, white (1 pe) 7 Blned flue inspetion piee, stright (1 pe) or Externl wll inspetion piee, 100 stright (1 pe) 8 Externl wll pk Comprising: Blned flue end Blned flue ir intke Wll ezel 9 Externl wll terminl for short roof overhng qp Blned flue end 87º (1 pe) º ( pe) or Mx. totl length of the flue pipe System size Ø mm Externl wll end 87º (1 pe) º ( pe) 100 qq Blned flue pipe 1.95 m long (1 pe) m long (1 pe) m long (1 pe) or Externl wll pipe 1.95 m long (1 pe) m long (1 pe) m long (1 pe) 100 qw Universl over pnels qe Blned flue roof outlet Externl wll with fixing lmps (for high roof overhng) Colour: lk or terrott ove roof extension with lmp (re on site) Colour: lk 0.5 m long m long Colour: terrott 0.5 m long m long qr Universl roof tile For Romn tiles nd pntiled roofs. Colour: lk or terrott for plin tile, slte nd other overs Colour: lk or terrott Pipe outlet for Klöer roof tiles Colour: lk or terrott (provide the orresponding Klöer tile on site to mth the roof outlet seleted for the prtiulr type of roof) Blned flue dptor Ø 80/15 mm to Ø 60/100 mm Ø 60/100 mm to Ø 80/15 mm Ø 80/15 mm to Ø 100/150 mm Vitodens 00-W, -F, -W, 4-F nd Vitosolr 00-F Rted output rnge kw mx. length - system size 60 m mx. length - system size 80 m 5 *1 5 *1 0 *1 1 1 mx. length - system size 100 m 17 *1 17 *1 0 0 Vitodens 300-W, 333-F nd 343-F Rted output rnge kw mx. length - system size 60 m mx. length - system size 80 m 15 *1 15 *1 15 *1 1 *1 x 87º lned flue ends re tken into onsidertion for the mximum flue lengths. Sutrt other ends, tees nd stright lengths from the mximum length using the following vlues: Blned flue ends 45º: 0.5 m Blned flue ends 87º: 1 m Blned flue inspetion tee: 0.5 m.5 Plsti (PPs) lned flue system for routing through lightweight shft spe sving shft for redued temperture requirements my e retrofitted if no shft is ville where the Vitodens is instlled in the living spe with one or more full storeys ove. *1 lterntive system size: order lned flue dptor seprtely. The shft used must omply with the requirements for domesti himneys to DIN V or must e generlly pproved y the uilding inspetorte. VITODENS VIESMNN 1

22 Design nd sizing informtion for onnetion on the flue gs side (ont.) "UNIFIX" shft profiles offered y Skoerne (mde from erted onrete) Ø mm Fire rting mm mm min min min min Ø "SKOBIFIXnno" nd "SKOBIFIXXs 30" shft profiles offered y Skoerne (mde from fomed ermis) Fire rting 30 min. Ø 60 Ø 80 Skoerne offer shft system mde from reeze onrete or fomed ermis with generl Building Regultions pprovl [Germny]. ddress for Skoerne: Skoerne Shornsteinsysteme GmH Ostendstrsse 1 D Pfungstdt nhoring for roof outlets with shft profiles (where the shft is run up to the roof skin) B C ville from Skoerne: Roof outlet B Universl roof tile C Terminl shft profile D nhoring of the roof outlet During instlltion, mth the terminl shft profile C to the roof pith. D VIESMNN VITODENS

23 Design nd sizing informtion for onnetion on the flue gs side (ont.) Promt shft profiles d Promt is one of the ompnies offering shft system mde from lium silite fire resistnt pltes pproved y the uilding inspetorte [Germny]. ddress for Promt: Promt GmH Postfh D Rtingen PROMTECT femle onnetion B PROMTECT fitting C Flue System size Ø mm mm mm mm d mm Fire rting min min min min B 100 C PROMTECT femle onnetion B PROMTECT fitting C Flue VITODENS VIESMNN 3

24 Design nd sizing informtion for onnetion on the flue gs side (ont.) Roof outlet for shfts with Promt profiles During instlltion, mth the finl shft profile to the roof pith. B C Vertil oxil roof outlet (lned flue system) B Universl roof tile C Lightweight shft mde from PROMTECT minerl fire profiles.6 Plsti (PPs) lned flue system for routing multiple pipes through shft There is n option of routing severl flues in lned flue mode through ommon, suffiiently sized shft. For this, the Vitodens ondensing oilers must e instlled in the sme living spe. For resons of fire protetion, the instlltion nd onnetion on different levels or in different rooms is not possile. The flues nd the shft overs must e professionlly supported inside/on the shft. For lned flue omponents from the Vitodens to the ommon shft, see pge Ventiltion ir B Flue gs C Inspetion port Lyout exmples Minimum lernes of the individul flues to DIN V : In squre/retngulr shfts: 0 mm In round shfts: 30 mm 4 VIESMNN VITODENS

25 Design nd sizing informtion for onnetion on the flue gs side (ont.) d System size Dimension [mm] Ø mm d Note ording to the pprovl ertifite, internl shft dimensions smller thn those shown in the tle my lso e used if this is indited y the funtion verifition to DIN EN Plsti (PPs) lned flue system (onnetion line) for onneting multiple flues to single room seled lned flue system The Vitodens ondensing oilers meet the sfety requirements to DIN Therefore, generl Building Regultions pprovl for onnetion to room seled lned flue is not required. When onneting two ondensing oilers to one himney on the sme floor, the onnetion piee inlets should e seprted y t lest 300 mm. Design nd lultions for room seled lned flue systems with multiple onnetions re rried out y the relevnt mnufturer. VITODENS VIESMNN 5

26 Design nd sizing informtion for onnetion on the flue gs side (ont.) Room seled lned flue system, negtive pressure (type C 43x to TRGI 008) H min. H mx. H Room seled lned flue systems for negtive pressure my, for exmple, e otined from the following mnufturers: ek Edelsthlkmin GmH D Untersteinh Jeremis Shornstein Systeme Opfenrieder Str. 1 D Wssertrüdingen Plew-Werke GmH D-5466 Speiher/Eifel Shiedel GmH & Co, Huptverwltung Lerhenstrsse 9 D Münhen Wienererger GmH Oldenurger llee 6 D Hnnover Effetive himney height reltive to the highest Vitodens B Ventiltion ir C Flue gs D Room seled lned flue system (see elow for mnufturers) E Inspetion port F Pressure lning perture G Chek with the flue system mnufturer regrding minimum lernes. Room seled lned flue system, positive pressure multiple onnetions with the Vitodens 00-W, - W nd -F up to 6 kw (type C 43x to TRGI 008) System for lned flue opertion, speifilly developed for the Vitodens 00-W, -W nd -F. Minimum shft ross-setion: mm squre Ø 195 mm round Up to 5 Vitodens 00-W, -W nd -F (up to 6 kw) with the sme rted output n e onneted to one flue system. Vitodens with different rted output levels n e onneted to the system if the relevnt lultions re verified. For this, plese omplete the enquiry form on pge 8. 6 VIESMNN VITODENS

27 Design nd sizing informtion for onnetion on the flue gs side (ont.) 4 1 B D C D 8 3 m D qp 9 qq qw.5 m 0 m System size Ø mm 1 Boiler flue onnetion (prt of the stndrd 80 oiler delivery) Flue gs non-return devie For instlltion in the Vitodens 00-W, -W nd -F (up to 6 kw) order seprtely for every oiler Stndrd shft set (PPs, rigid) 100 Comprising: Support end Support ril Shft over (PPs) Spers (3 pe) Spers (3 pe) Blned flue end 87º (1 pe) 80 45º ( pe) 80 or Blned flue inspetion end 80 87º (1 pe) 4 Blned flue dptor 80 Ø 60/100 to Ø 80/15 5 Blned flue inspetion piee, stright 80 (1 pe) 6 Blned flue slide oupling 80 Fixing lmp, white (1 pe) (lned flue 80 pipe) 7 Wll ezel 80 8 Blned flue pipe 1 m long m long 80 9 Conneting ssemly multiple onnetion 100 Comprising: Inspetion pipe Ø 100 Flue outlet Ø 80 Fixing lmp Spers Long fem. onnetion Ø 100 qp Conneting ssemly; ondenste drin 100 D qr E qe Flue gs B Ventiltion ir C Drining ondenste into the vertil flue D Inspetion port E Condenste drin with siphon Comprising: Brnh 87 Ø 40 Fixing lmp Long fem. onnetion Ø 100 qq Connetion lip required for every shft 100 joint qw Flue pipe m long ( m = 4 m) 100 m long (1 pe) m long (1 pe) m long (1 pe) 100 Flue end (for use in orelled himneys) 30º ( pe) º ( pe) 100 qe Inspetion piee, stright (1 pe) 100 qr Condenste drin onnetion (eentri) 100 Reduer from Ø 100 mm to Ø 40 mm VITODENS VIESMNN 7

28 Design nd sizing informtion for onnetion on the flue gs side (ont.) Enquiry form for flue system with multiple vertil onnetions Heting ontrtor Building/uilding projet Tel.: L4 L3 L L1 Fx: Contt: L5 Ho H1 H H3 H4 H5 Hu Boiler Rted output kw Type Fuel ê Nturl gs ê LPG Horizontl onnetion line Extended length m L1: L: L3: L4: L5: Numer of ends 87 : 45 : 87 : 45 : 87 : 45 : 87 : 45 : 87 : 45 : Vertil line in shft Clerne etween omustion m H1: H: H3: H4: H5: pplines Height ove the highest omustion m equipment Height ove the lowest omustion m equipment Height in old re m Height in open ir m Shft ville ê Yes ê No Shft design ê Vertil ê Offset Shft ross-setion mm ê Round, Ø mm ê Ovl,... x... mm ê Squre,... x... mm ê Retngulr,... x... Shft mteril Plese send this enquiry form to your regionl quottion entre. The ddress nd ontt detils n e found in the ppendix to the Viessmnn prielist. 8 VIESMNN VITODENS

29 Design nd sizing informtion for onnetion on the flue gs side (ont.).8 Plsti (PPs) flue pipe for routing through shft with open flue opertion (type B ording to TRGI 008) Open flue opertion requires flue pipe s the onnetion piee etween the Vitodens nd the shft s well s for the routing through the shft. The instlltion room must provide n ir vent with n unrestrited ross-setion of t lest 150 m or 75 m (ording to TRGI 008). Note Instll the Vitodens 00-W, from 60 kw, nd multi oiler systems in ordne with FeuVo [or lol regultions] in seprte instlltion room with suitle ir vent. The ross-setion should e t lest 150 m nd should e m lrger for eh kw ove 50 kw rted output. This ross-setion my not e split over more thn pertures (oserve FeuVo nd TRGI 008, or hek lol fire regultions). Internl flue dimeter Ø in mm Vitodens 00-W to 35 kw, Vitodens - 60 F, Vitodens -W, Vitodens 4-F, Vitodens 300-W, Vitodens 333-F, Vitodens 343-F nd Vitosolr 00-F Vitodens 00-W, 45 to 60 kw 80 Vitodens 00-W, 80 to 105 kw 100 The flue system is onneted to the oiler flue onnetion. The omustion ir is drwn from the instlltion room vi the nnulr gp in the oiler flue onnetion. For instlltion through shfts or hnnels with longitudinl ventiltion meeting the requirements for domesti himney stks to DIN V , or with fire rting of 90 minutes (L90), or fire rting of 30 minutes (L30) for uildings in tegories 1 nd. Prior to instlltion, the flue gs inspetor should hek tht the shft to e used is suitle nd pproved for this purpose. Shfts tht were previously onneted to oil or solid fuel oilers must e thoroughly lened y himney sweep. Loose deposits omprising sulphur nd soot must not remin on the inside of the himney. Close off nd sel ny other onnetion pertures with pproprite mterils. This does not pply to ny lening or test pertures tht re provided with himney lening overs nd tht re identified with n pproprite test mrk. Chek prior to instlltion whether the shft runs stright from top to ottom or if it is offset (hek with mirrors). If the himney is offset, we reommend the instlltion of flexile flue (see pge 31). The lol flue gs inspetor should hek the flue system for tightness prior to ommissioning (where pplile). In the se of open flue opertion, this n only e rried out y mens of pressure test. Inside the instlltion lotion, t lest one inspetion port must e provided in the flue system for heking nd lening s well s for heking the pressure. If the flue pipe is inessile from the roof, seond inspetion port must e provided in the tti ehind the himney lening hth. Sfegurd the drining of the ondenste from the flue pipe to the oiler with fll of t lest 3º. Route the flue system over the roof (oserve the roof lerne prllel to the roof inlintion ording to the Lndes-FeuVo [or lol regultions]). lterntive CE-designted flue pipes my e used, for exmple, if lrger flue pipe dimeter is required, i.e. euse of greter flue lengths. In tht se, the funtion verifition to EN should e provided y the relevnt flue pipe mnufturer. Internl shft dimensions Minimum internl shft dimensions System size Externl dimeter; Minimum internl shft dimension femle onnetion squre or retngulr round (short side) Ø mm mm Ø mm (flexile) (flexile) (flexile) Mx. numer of ends: 87º: 3 pe or 45º: 3 pe or 30º: 4 pe or 15º: 4 pe The nnulr gp must e t lest 3 m wide t the shft inlet. VITODENS VIESMNN 9

30 Design nd sizing informtion for onnetion on the flue gs side (ont.) Flue, system size 60, 80 nd 100 (omponents) (type B 3 /B 33 ording to TRGI 008) C 6 E D E E B Ventiltion ir For sizing the ir vent, see pge 9 B Flue gs C Inspetion port D Connetion piee E Seondry ventiltion C System size Ø mm 1 Boiler flue onnetion (prt of the stndrd oiler delivery) Stndrd shft set (PPs, rigid) Comprising: Support end Support ril Shft over Spers (3 pe, mx. distne 5 m) or Stndrd shft pk (metl/pps, rigid) for twin drught himneys; one drught for solid fuel oilers omprising: Support end Support ril Shft over (metl) Terminl pipe (stinless steel) Spers (3 pe, mx. distne 5 m) Spers (3 pe, mx. distne 5 m) Flue pipe 1.95 m long ( 1.95 m = 3.9 m) 1.95 m long (1 pe) m long (1 pe) m long (1 pe) Inspetion piee, stright (1 pe) Flue end º (1 pe) 45º ( pe) or Inspetion tee º (1 pe) or Inspetion end º (1 pe) 6 Ventiltion ezel (1 pe) Flue end (for use in orelled himneys) º ( pe) 15º ( pe) Stinless steel extension, 380 mm long for shft over, stndrd shft pk (metl/pps, rigid) (for system size 60, n extension Ø 60 mm to Ø 80 mm is required) Extension Ø 60 mm to Ø 80 mm Ø 80 mm to Ø 100 mm Mx. totl length of the flue pipe Vitodens 00-W, -F, -W, 4-F nd Vitosolr 00-F Rted output rnge kw mx. length - system size 60 m mx. length - system size 80 m 5 *1 5 *1 5 * mx. length - system size 100 m 5 *1 0 *1 0 0 Vitodens 300-W, 333-F nd 343-F Rted output rnge kw mx. length - system size 60 m mx. length - system size 80 m 17 *1 17 *1 0 *1 15 *1 *1 lterntive system size: order lned flue dptor seprtely. 30 VIESMNN VITODENS