PowerView. Model AP9215. User s Manual

Transcription

1 PowerView Model AP9215 User s Maual

2 Thak You! Thak you for selectig the America Power Coversio PowerView. It has bee desiged for may years of reliable, maiteace-free service i combiatio with your America Power Coversio Uiterruptible Power Source. America Power Coversio is dedicated to the developmet of high-performace electrical power coversio ad cotrol products ad we hope that you will fid this product a valuable, coveiet additio to your computig system. Please read this maual! It provides importat istallatio ad operatig istructios that will help you get the most from your PowerView. Save this maual! It icludes istructios for obtaiig factory service should the proper operatio of the accessory come ito questio..

3 Cotets Itroductio... 2 Supported UPS Models...2 Cotrols ad Idicators... 3 Istallatio... 4 Geeral Navigatio... 5 Meu Structure... 6 Cotrol... 7 Status... 8 Setup... 9 Accessories Loggig PowerView Iformatio ad Cofiguratio Diagostics Help Replacig the Laguage EPROM Moutig Template

4 Itroductio PowerView is a compact cotrol pael ad display which provides full cotrol, moitorig ad cofiguratio of the coected UPS. Figure 1 PowerView Frot Pael Supported UPS Models PowerView supports the followig APC UPS model families: Smart-UPS: SU450, SU700, SU1000, SU1400, SU2200, SU3000 Matrix-UPS: all models Symmetra: all models The followig APC UPS families are ot supported by PowerView: Back-UPS: all models Smart-UPS: AP250, AP400, AP600, AP900, AP1250, AP2000, SUVS420, SUVS650, SUVS1000, SUVS1400, SU420, SU620 2

5 Cotrols ad Idicators Idicators Figure 2 Frot Pael Idicators LOAD ON: Idicates that the load coected to the UPS is receivig power (O-lie, O-Battery or Bypass). ON BATT: Idicates that power to the attached load is beig supplied by the UPS s batteries (uavailable while i Bypass). BYPASS: Idicates that power to the attached load is beig supplied through the UPS s filterig ad surge suppressio circuits directly. The UPS will ot power the load from battery i the evet of a power failure. (This feature is available oly o Matrix-UPS ad Symmetra models). FAULT: Idicates that the UPS has detected a problem or certai cofiguratio chages (icludes both hardware failures ad abormal coditios such as overload or over temperature). Cotrols The cotrol keys are used to avigate betwee meus, to select meu items, ad to iput alphaumeric iformatio. The sectio etitled Geeral Navigatio o page 6 provides additioal iformatio. Figure 3 Cotrol Keys 3

6 Istallatio PowerView is coected directly to the UPS through a sigle iterface cable (PN ) icluded with the PowerView uit. Follow the steps below to coect PowerView to the UPS: 1. Coect the modular RJ45 plug o the ed of the iterface cable to the coector at the rear of PowerView. 2. Check the rear of the UPS to determie whether there is a cable already coected to the 9-pi computer iterface coector. If there is a cable already coected to this coector, shut dow ay UPS moitorig software ruig o the host system, the loose the thumb screws ad remove the existig cable. If there is o cable coected, cotiue with Step Coect the male ed of the cable to the computer iterface coector at the rear of the UPS ad secure it with the thumbscrews. 4. If it was ecessary to remove a cable i Step 2, coect the removed cable to the female coector o the cable ad tighte the thumb screws. If o cable was removed, the uused coector may be left ucoected. PowerView may be mouted to the wall with screws usig features o the back or it may be mouted with the supplied hook ad loop fasteers. A template for moutig PowerView to the wall is supplied at the ed of the maual. PowerView will also sit upright o a flat surface by foldig out the wire bail o the rear of the uit. Figure 4 PowerView Iterface Cable 4

7 Geeral Navigatio Note: Throughout this maual the four avigatio keys will be represeted as: Esc,,, ad Eter ( ). Specific meus are refereced i the form Display:Password where Display refers to a meu item i the top-level meu ad Password refers to a submeu of Display. The default scree will appear whe PowerView is first powered o or after ay exteded period of iactivity. Pressig ay key will access the top level meu. Whe i ay meu, pressig or will move the cursor ( ). The Eter key ( ) will advace you deeper ito the meu tree. The Esc key will back out to the paret meu. The meu tree is outlied i the followig pages. For status or iformatio screes there is o cursor, the or keys act like page up/dow keys to show multiple screes, if appropriate. For settigs meus, poit ( ) to a parameter ad press Eter ( ); the cursor will move adjacet to the parameter value ad become a. The or keys will ow icremet or decremet the value. The value displayed takes effect immediately. Whe the desired value is displayed, press either Esc or Eter ( ) to exit the selectio mode. (Both Esc ad Eter ( ) have exactly the same fuctio i this case.) Pressig ad simultaeously will display cotext sesitive help o most screes ad meus. Note that cotrol ad cofiguratio fuctios ca be password protected (see the Display:Password meu). Also, the default scree is user cofigurable (see the Display:Cofig meu). 5

8 Meu Structure PowerView s meu structure is divided ito eight(8) fuctioal groups. These groups are: Cotrol Status Setup Accessories Loggig PowerView Iformatio ad Cofiguratio Diagostics Help The fuctios ad status iformatio available for each of these groups is outlied i the followig pages. 6

9 Cotrol UPS O/Off Do Self Test UPS verifies proper system operatio by briefly powerig the attached load from battery. Simulate Power Fail causes UPS sigalig port to immediately idicate that the AC lie has failed. This may iitiate a orderly server shutdow sequece if the appropriate cable ad software drivers are used. Graceful Reboot iitiates a orderly server shutdow ad restart sequece if the appropriate cable ad software drivers are used. The sequece is: 1. The UPS sigalig port idicates that the AC lie has failed ad that the UPS battery is low. (Server will quickly begi shutdow if so cofigured.) 2. After the Low Battery Duratio time plus the Shutdow Delay time (user settable parameters i Setup:Shutdow) the UPS will tur off for the Retur Delay time (user settable parameter i Setup:Shutdow) the come back o uless: (1) the iput AC lie voltage is out of tolerace or (2) the battery capacity is below the Retur Battery Capacity (user settable parameter i Setup:Shutdow). Graceful Tur Off same as Graceful Reboot above except that the attached load remais off util tured o by the user via the Cotrol:Tur Load ON commad. Start/Stop Rutime Calibratio causes UPS to ru o battery util the battery(s) is(are) discharged to approximately 25% of capacity. Data recorded durig this time improves the accuracy of the Rutime estimate which the UPS reports i the Status scree. Recommeded testig iterval: oce per moth. UPS ito/out of Bypass (Matrix ad Symmetra oly) Whe bypassed, power to the attached load is beig supplied through the UPS s filterig ad surge suppressio circuits directly. The UPS will ot power the loadfrom the battery i the evet of a power failure. This is geerally used durig maiteace o modular UPSs. 7

10 Status Status Display 1 Ÿ Iput Lie Voltage ad Frequecy Ÿ Output Voltage Ÿ Rutime Estimate Ÿ Load (i Amps ad % of VA capacity) Status Display 2 Ÿ UPS iteral temperature Ÿ Last Trasfer: the cause of the most recet o-battery evet. Noe - the UPS has ot bee o battery recetly. Test - a self-test caused the UPS to briefly ru o battery. Notch/Spike - AC lie voltage was o-siusoidal or severely distorted; icludes total power failure. Low Voltage - AC lie voltage wet below the lower trasfer poit. The lower trasfer poit is user adjustable i certai UPS models, see Setup:Trasfer meu. Hi Voltage - AC lie voltage exceeded the upper trasfer poit. The upper trasfer poit is user adjustable i certai UPS models, see Setup:Trasfer meu. Rate of Chg - abrupt chage i lie voltage CirBrkr Trip - iput circuit breaker tripped (Symmetra oly) Ÿ Status: a terse idicatio of the state of the UPS. The most commo are O-Lie (AC lie quality is acceptable), UPS/ Load off, O-battery (load is powered from battery), Low- Battery (battery is fully discharged), Overload, or ay oe of a umber of iteral faults. Use Diagostics from the top level meu for a detail of the UPS status ad faults. Ÿ Number of istalled batteries ad bad batteries (Matrix-UPS ad Symmetra oly) 8

11 Status Display 3 Ÿ Battery voltage Ÿ % Battery Capacity Ÿ Result of last Selftest: Noe o recet selftest OK most recet selftest was satisfactory Uavail uavailable Ca t Tst UPS could ot perform the test at the time. Failed battery coditio has deteriorated below a reliable level, the battery should be replaced. Setup Trasfer these first three parameters cotrol whe the UPS switches to battery. Ÿ Low Xfer (Lower trasfer voltage) the output voltage at which the UPS switches trasformer taps or oto battery. Ÿ High Xfer (High trasfer voltage) the output voltage at which the UPS switches trasformer taps or oto battery. (If you otice that the iput voltage is geerally close to oe ed of the lower/upper voltage widow, it may be ecessary, depedig o the load s voltage requiremets, to receter the widow by chagig the lower ad/or upper trasfer voltages) Ÿ Sesitivity sudde, small chages i iput voltage will cause the UPS to briefly ru o battery. (If you otice, or the evet log idicates, that the UPS trasfers to battery frequetly, it may be ecessary, depedig o the load s voltage requiremets, to lower the sesitivity oe step at a time. If the UPS still trasfers frequetly, check the lower/upper trasfer voltage widow described above). Ÿ Output (oly o 220/230/240V UPSs) allows selectio of omial output voltage. 9

12 Shutdow these parameters affect sigalig via the UPS s iterface port. They are geerally used i the cotext of cotrollig a orderly shutdow of a attached server i the evet of a power failure or a user iitiated Graceful Reboot or Graceful Off. Ÿ Low Battery Duratio legth of time betwee low battery sigallig ad shutdow of power to the attached load. (Set this for log eough to allow the server to perform its shutdow process) Ÿ Shutdow The legth of time betwee a shutdow commad (from the computer to the UPS) ad shutdow of power to the attached load. This is to allow a server time to gracefully complete its shutdow process. Ÿ Retur Delay the miimum legth of time that the UPS will wait before restorig power to the attached load after retur of ormal lie voltage. Note: the UPS may wait loger tha this if the battery capacity is less tha the value of Retur Battery Capacity. Ÿ Retur Battery Capacity The miimum percetage of battery capacity required before power is restored to the attached load after retur of ormal lie voltage. Other Ÿ Self Test The UPS ca be cofigured to perform a selftest automatically at selectable time itervals. Ÿ UPS ID the user ca store up to 8 characters of descriptive text i the UPS for idetificatio purposes. This settig has o effect o the operatio of the UPS. Allowable characters are: A-Z, 0-9,/, space. Ÿ Battery Date Set at the factory to the date the battery was istalled (mm/dd/yy format). If the user replaces the battery, the date should be updated for future referece. This settig has o effect o the operatio of the UPS. Allowable characters are: 0-9,/, space. Ÿ Exteral Battery Packs i SmartUPS which have exteral batteries (havig XL i the model umber), the user must tell the UPS how may exteral battery packs are attached so that the Rutime estimate will be correct. This is importat ot oly for the displayed rutime estimate but also for the Low Battery Duratio time (advace warig of impedig discharged battery). 10

13 UPS Iformatio Display Ÿ Model Name Ÿ Firmware Revisio Level Ÿ Serial Number Ÿ Maufacture Date Copy PowerView ca lear the cofiguratio of a UPS ad subsequetly write that data to the same or a differet UPS. Up to five UPS cofiguratios ca be stored i PowerView s memory. First select the cofiguratio that you wish to move UPS data ito or out of, the select the directio that you wish to move the data. Copyig data betwee differet voltage versios may ot yield optimum results; i particular, the output voltage selectio should be reviewed by the user. Copyig betwee differet product lies may leave some parameters i the target UPS set to factory defaults, especially whe copyig from a product with less capability to oe with more capability. Ÿ Cofiguratio umber Ÿ From UPS to Display Ÿ From Display to UPS Accessories APC sells accessories which plug ito the back of the UPS, such as evirometal moitors ad power cotrol devices. If supported accessories are istalled, status ad setup meus are foud here. Measure-UPS II Ÿ Probe 1 or 2 status display Ambiet Temperature ad Humidity Upper/Lower alarm limits for Temperature ad Humidity Ÿ Probe 1 or 2 setup Upper/Lower alarm limits for Temperature ad Humidity Ÿ Zoe Status shows the states of the 4 iputs as ormal or alarm. 11

14 Loggig PowerView keeps a log of up to 64 of the most recet evets. The user ca clear the log ad filter certai evet types from beig logged. View Log the poits to a evet; the date, time ad umber of that evet are displayed o the top lie. Evet 1 is the oldest. Press Eter ( ) for a more verbose descriptio of the evet. The ad keys scroll through evets. Press Esc to revert back to three evet viewig. View Statistics a absolute cout of evets witessed by PowerView. Ÿ Trasfers to Battery Ÿ Low Battery (battery must be fully discharged to be couted) Ÿ Faults or abormal coditios Ÿ Total accumulated rutime o battery Cofigure Loggig see the List Evet Groups screes to see what evets each category icludes. Loggig of each evet group may be idividually eabled or disabled. Ÿ Power Evets Ÿ UPS Cotrol Ÿ UPS Faults Ÿ User Activity Ÿ Measure-UPS Evets List Evet Groups Ÿ Power Evets Ÿ UPS Cotrol Evets Ÿ UPS Faults Ÿ User Activity Ÿ Measure-UPS evets Clear Log 12

15 PowerView Iformatio ad Cofiguratio Set curret date ad time (used for log etries) Password whe a o-ull password is cofigured, all cotrol ad cofiguratio fuctios provided by PowerView will require the user to eter the password. The default from the factory is o password. Ÿ Set password press eter ad use the ad keys to set a character strig of up to 8 characters. The uderscore ( _ ) character is used to idicate the ed of a password that is less tha 8 characters i legth. Settig the first character of the password to uderscore disables password protectio. Allowable characters are: A-Z, 0-9,/, space. Ÿ Password timeout a period of user iactivity greater tha this value will require re-etry of the password. The legth of iactivity before PowerView reverts to the default data scree is also determied by this settig. Ÿ Ivalidate (timeout) the password immediately ay sucessive attempt at cotrol or cofiguratio fuctios will require eterig the password. Iformatio about PowerView Ÿ Model Number Ÿ Serial Number Ÿ Maufacture Date Ÿ Hardware ad Firmware Revisio Levels Beeper Settigs Ÿ At UPS coditio whe the UPS will beep Ÿ At Display coditio whe PowerView will beep Ÿ Beeper Volume Ÿ Key click o/off Cotrast adjust for optimum viewig of display. 13

16 Cofiguratio of default scree After selectig this optio, the scree will appear as the default data scree with the exceptio of a cursor i the upper left corer. The ad keys will select the lie that you wish to chage. Pressig Eter ( )chages the cursor to ad the ad keys will ow select the cotets of that lie. Press Eter ( ) oce selectio is made. Diagostics If there are multiple faults or abormal coditios, pressig ay key will move through the list. Help Pressig ad simultaeously will display cotext sesitive help o most screes ad meus. 14

17 Replacig the Laguage EPROM PowerView ca be cofigured to display text i a laguage other tha the default Eglish by replacig the uit s laguage EPROM with oe of the alterate laguage EPROMs icluded with the uit. Follow these steps to replace the uit s laguage EPROM: Note: The device beig replaced is static sesitive. Do ot remove it from the protective carrier util you are ready to isert it i the uit. 1. Remove the four (4)Phillips screws o the rear of the uit ad separate the frot half of the case from the rear. 2. Idetify the laguage EPROM. This is a 28-pi itegrated circuit located i a socket ad adjacet to the large 40-pi device. The laguage EPROM will have a white label bearig the ame of the laguage for which it is programmed. Note which ed of the EPROM has the semicircular otch (pi 1); the ew EPROM must be istalled with the same orietatio as the origial. 3. To remove the EPROM, isert a small screwdriver or similar tool betwee the EPROM ad its socket. Getly twist the blade to lift the EPROM from the socket. I order to avoid bet pis, the EPROM should be looseed gradually, oe side at a time, util it is free of its socket. 4. Positio the ew EPROM o its socket with the otch i the same relative positio as the origial. Carefully check that all pis are aliged with the socket. Realig if ecessary. Apply eve pressure with figers to the top of the EPROM util it is fully seated i its socket. 5. Replace the rear cover ad re-istall the four (4) Phillips screws. Figure 5 Locatio of Laguage EPROM 15

18 Moutig Template Figure 6 Wall Moutig Template 16

19

20 Toll free techical support: Addresses: Uited States ad Caada Irelad U. K I areas without toll free umbers, call: (USA) or (Irelad) America Power Coversio Corporatio 132 Fairgrouds Road P. O. Box 278 West Kigsto, Rhode Islad USA America Power Coversio Corporatio (A. P. C.) b. v. Ballybritt Busiess Park Galway Irelad Serial umber: Etire cotets copyright 1997 America Power Coversio. All rights reserved; reproductio i whole or i part without permissio is prohibited. PowerView is a trademark of APC. All other trademarks are the property of their respective owers Rev. 1 07/97