Quick Coupling Products

Transcription

1 Quick oupling Products Quick ouplings, Swivels, heck Valves, iagnostic Equipment atalog 3800 US November 2008

2 Parker Locations Minneapolis, Minnesota Grantsburg, Wisconsin Lincoln, Nebraska hetek, Wisconsin FILURE OR IMPROPER SELETION OR IMPROPER USE OF THE PROUTS N/OR SYSTEMS ESRIE HEREIN OR RELTE ITEMS N USE ETH, PERSONL INJURY N PROPERTY MGE. This document and other information from Parker Hannifin orporation, it's subsidiaries and authorized distributors provide product and/or system options for further investigation by users having technical expertise. It is important that you analyze all aspects of your application and review the information concerning the product or system in the current product catalog. ue to the variety of operating conditions and applications for these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met. The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin orporation and its subsidiaries at any time without notice. Offer of Sale The items described in this document are hereby offered for sale by Parker Hannifin orporation, its subsidiaries or its authorized distributors. This offer and its acceptance are governed by the provisions stated in the Offer of Sale. 2008, Revised November 2008, Parker Hannifin orporation, ll Rights Reserved Lewis Road Minneapolis, MN 55427

3 Quick oupling Products Table of ontents Pneumatics Pneumatic Quick ouplings...section Introduction...-2 oupling Selection Guide...-4 Interchange Match-up hart...-5 Industrial Interchange Nipples...-6 General Purpose...-8 Special Purpose ccessories Hydraulic Quick ouplings...section Introduction...-2 oupling Selection Guide...-4 General Purpose...-5 Non-Spill onnect-under-pressure High Pressure Mold oolant Line High Flow Special Purpose - Miniature ust Plugs and aps Ordering Information Promotional Products-Keychains Thermoplastic ouplings...section oupling Section Guide...-3 Spectrum Series...-4 PF Series...-8 Ordering Information Swivels...Section Introduction...-2 PS Series...-4 PS Series In-Line Swivels...-6 PS Series 90 Swivels PS Series Repair Kits S Series Swivels S Series Repair Kits heck Valves...Section E Introduction...E-2 Features & General Technical Information...E-4 T Series...E-5 V Series...E-9 Ordering Information...E-8, E-11 iagnostic Products (Sensoontrol )...Section F Introduction...F-2 Selection Guide...F-4 ServiceJunior...F-5 Sensoontrol Serviceman...F-6 Serviceman ccessories...f-14 - F-17 Sensoontrol Service Master...F-10 Service Master ccessories...f-14 - F-17 Sensoontrol Pressure Transducers...F-15 Sensoontrol Flow Sensors...F-16 Test Port ouplings...f-18 Ordering Information...F-27 ppendices...i-v Fluid ompatibility hart...i Safety Guide...II lpha Numeric Index...III Glossary of Terms...IV Offer of Sale...V orporate Overview...Inside ack over ppendices F iagnostic E heck Valves Swivels Thermoplastics Hydraulics Parker Hannifin orporation Minneapolis, MN 55427

4 Pneumatics Pneumatic Quick ouplings -1

5 Pneumatics Pneumatic Quick ouplings Single Shut-Off ouplings Single Shut-Off couplings are primarily used for pneumatic applications, connecting air tools, hoses, or other implements to compressed air supplies. They are also used with other gases, and with the exception of the E-z-mate Series can be used with low pressure fluids. The coupler half contains a shut-off valve that is automatically opened when a mating nipple is inserted and automatically closes when the nipple is removed. Parker Single Shut-Off couplings come in three basic designs: general purpose/manual connect, general purpose/push-to-connect, and special purpose. Introduction The standard seal material for all Parker Single Shut-Off couplers is Nitrile. Ethylene Propylene, Fluorocarbon, and Neoprene seals are available as options. See the comprehensive Fluid ompatibility hart that provides guidelines for seal and body material selection. When there is need for further assistance in selecting the appropriate seal material, please consult factory. General Ordering Information When ordering Parker coupler bodies and nipples, please state the part number of each type of coupler body and each type of nipple desired. List coupler bodies and nipples as separate items rather than in combinations. e sure to double check thread or hose sizes of items required. Many of Parker s coupling products are available with unique non-standard options well suited to very specific applications. Examples of unusual end use applications might include: high temperatures (above 250 F), extremely caustic/corrosive solutions passing through the coupling, external/environmental corrosion situations, or other high wear and tear situations such as dragging the product along the ground. It is always recommended that the Quick oupling ivision be contacted with any questions concerning specific product application needs. Typically, a prefix or suffix is added to the base part number to specify a non-standard O-ring seal, or special option such as a sleeve lock. The list at right illustrates the designations. Please Note: ertain couplings series have additional Special Order Information which should be referred to in ordering those products. If applicable to the product, Special Order Information is found next to the Features and Specifications charts. See the oupling Selection and Ordering Guide for further information. hecklist for Selecting Quick ouplings What are the functional requirements of the coupling? What is the maximum working pressure of the application? Which seals and body material are compatible with the system s fluid? Is the application static or dynamic? What size coupler is required? What is the maximum pressure drop suitable for the application? oes the application require the ability to connect and disconnect under pressure? What is the media temperature and ambient temperature? What end configurations are required? Is an industry interchange coupler required? Is air inclusion and fluid loss a concern in the application? -2

6 Pneumatic Quick ouplings Table of ontents Pneumatics Introduction...-2 oupling Selection & Ordering Guide...-4 Interchange Match-up hart...-5 Industrial Interchange Nipples...-6 to -7 General Purpose ouplings Manual onnect Series...-9 ouplers Nipples Series ouplers Series ouplers Nipples Series ouplers Nipples Push-to-onnect RF Series ouplers Nipples Tool-Mate Series...See pages -33 to -36 HF Series ouplers 1/8" Nipples 1/8" ouplers 1/4", 3/8" & 1/ HF Series Heavy uty ouplers 1/4" & 3/8" H Series ouplers Nipples Universal oupler ouplers Series to -30 ouplers to -30 Twist-Lock ouplings ouplers Nipples Special Purpose ouplings Standard - Non Marring omposite Tool-Mate Series ouplers Exhaust - Non Marring omposite Tool-Mate Series ouplers Exhaust - Steel E-z-mate Series ouplers ccessories low Guns ontrolled Pressure Full Pressure G Series Two-Way Valves

7 Pneumatics Pneumatic Quick ouplings General Purpose Manual onnect oupling Selection & Ordering Guide oupler ody Material* Locking Std. Seal** Std. Seal** Rated Style Interchange Size (in.) SS S P Mechanism Material Temp Range Pressure 10 Series Manual Tru-Flate 1/4 to 1/2 all Nitrile -40 to +250 F 300 PSI 20 Series 1 Manual Industrial 1/4 to 1/2 all Nitrile -40 to +250 F 300 PSI 50 Series Manual RO 210 1/4 all Nitrile -40 to +250 F 300 PSI 70 Series Manual Lincoln 1/4 all Nitrile -40 to +250 F 300 PSI (long stem) General Purpose Push-To-onnect RF Series Push to onnect EJN 320/410 1/4 & 3/8 all Nitrile -40 to +250 F 300 PSI Rectus 25/27 HF Series Push to onnect Industrial 1/8 2 all Nitrile -40 to +250 F 300 PSI to 1/2 30 Series Push to onnect Industrial 1/4 to 3/4 Pawl Nitrile -40 to +250 F 300 PSI H Series Push to onnect RO 210 1/4 all Nitrile -40 to +250 F 300 PSI Twist Lock Push to onnect Schrader 1/4 to 1/2 am Nitrile -40 to +250 F 300 PSI Universal Push to onnect Industrial 1/4 all Nitrile -40 to +250 F 150 PSI Tru-Flate RO 210 Special Purpose Push-To-onnect E-z-mate Series Exhaust/ Industrial 1/4 to 3/4 all Nitrile -40 to +250 F 300 PSI Push to onnect Tool-Mate Series Push to onnect/ Industrial & 1/4 to 1/2 3 Fingers Nitrile -40 to +250 F 300 PSI Exhaust & Std EJN 320 / Rectus Series Stainless Steel available in 1/4 body. 2 1/8 couplings have no standard industry interface. 3 Tool-Mate metal end ports are Galvanized Steel. * Material ode: = rass; SS = Stainless Steel; S = Steel; P= Plastic oupling Material oupler Prefix for rass - available for 3/8 & 1/2 body sizes only Suffix N for Stainless Steel springs, locking balls and brass valves. (10, 20, 30, 50, and 70 series only) Nipple Prefix for rass (Standard material is steel) **Optional Seals Material Suffix TEMP Range Ethylene Propylene W -65 to +400 F Fluorocarbon Y -30 to +400 F To select proper seal materials, see Fluid ompatibility hart in ppendices section, or contact your Parker Quick oupling istributor. -4

8 Pneumatic Quick ouplings Popular oupling esigns Parker s manufactures quick couplings to interchange with popular designs that have become accepted standards in the industry today. The actual Interchange Match-up hart size nipple chart below can be used to help select Parker Quick ouplings that will interchange with specific nipple designs and sizes. Pneumatics 10 Series (Tru-Flate Interchange) 20 Series, 30 Series, HF Series, E-z-mate (Industrial Interchange) 1/8" HF Series 50 Series (RO-210 Interchange) 1/4" ody Size 1/4" ody Size 3/8" ody Size 1/8" ody Size 1/8" ody Size 70 Series (Lincoln Interchange) 1/4" ody Size 1/4" ody Size 1/2" ody Size 3/8" ody Size RF Series Twist-Lock (Schrader Interchange) 1/4" ody Size 1/4" ody Size 1/2" ody Size 3/8" ody Size 3/8" ody Size 1/2" ody Size 3/4" ody Size -5

9 Pneumatics Pneumatic Quick ouplings Industrial Interchange Nipples Features Parker Industrial Interchange nipples are for use with any Parker 20 Series, HF Series, 30 Series, Universal, HF or E- z-mate couplers. Parker Industrial Interchange nipples are interchangeable with similar nipples manufactured by other quick coupling manufacturers conforming to (formerly known as MIL--4109F), NSI/(NFP) T , or ISO6150- requirements. Hardened wear points** and solid barstock construction provide extended service life. Precision machined surfaces and hardened load-bearing areas** resist the effects of mechanical shock in the most rugged applications. The 20 Series, HF Series, 30 Series, Universal and E-z-mate couplers that mate with the Industrial Interchange nipples are located in their respective coupling Type (e.g. Manual Type) as noted in the Table of ontents. ** steel nipples only Female Pipe Thread ody Part Part Part No. Thread imensions (in.) Size No. No. Type 303 Size Overall Exposed Hex Largest Wt. (L.) (in.) rass Steel Stainless NPTF Length Length* Size iameter P/Piece E F G E F G 1/4 H1 1/ /4 H3 H3 SH3 1/ /4 H3-E SH3-E 3/ /8 H1E 1/ /8 H3E H3E 3/ /8 H3E-F 1/ /2 H1F 3/ /2 H3F H3F 1/ /2 H3F-G 3/ /4 H3G-F 1/ /4 H3G 3/ /4 H3G-J / *This dimension represents portion of nipple that is exposed when nipple is inserted in a Parker 20 Series coupler. -6

10 Pneumatic Quick ouplings Male Pipe Thread E F G Industrial Interchange Nipples ody Part Part Part No. Thread imensions (in.) Size No. No. Type 303 Size Overall Exposed Hex Largest Wt. (L.) (in.) rass Steel Stainless NPTF Length Length* Size iameter P/Piece E F G 1/4 H0 1/ /4 H2 H2 SH2 1/ /4 H2-E SH2-E 3/ /8 H00E 1/ /8 H0E 1/ /8 H2E H2E 3/ /8 H2E-F 1/ /2 H0F 3/ /2 H2F H2F 1/ /2 H2F-G 3/ /4 H2G-F 1/ /4 H2G H2G 3/ /4 H2G-J / Pneumatics *This dimension represents portion of nipple that is exposed when nipple is inserted in a Parker 20 Series coupler. Standard Hose arb E G ody Part Part Part No. imension (in.) Size No. No. Type 303 Hose Overall Exposed Largest Wt. (L.) (in.) rass Steel Stainless I.. Length Length* iameter P/Piece E G 1/4 H8 1/ /4 SH8 1/ /4 H8-5/ /4 H9 SH9 3/ /8 H5E 3/ /8 H6E 1/ /2 H4F 3/ /2 H5F 1/ /2 H5F-G 3/ /4 H5G-F 1/ /4 H5G H5G 3/ /4 H5G-J * This dimension represents portion of nipple that is exposed when nipple is inserted in a Parker 20 Series coupler. Push-Lok Hose arb** E G ody Part Part imension (in.) Size No. No. Hose Overall Exposed Largest Wt. (L.) (in.) rass Steel I.. Length Length* iameter P/Piece E G 1/4 H8P H8P 1/ /4 H9P 3/ /8 H4EP 1/ /8 H5EP 3/ /8 H6EP 1/ /2 H4FP 3/ /2 H5FP 1/ /2 H6FP 5/ *This dimension represents portion of nipple that is exposed when nipple is inserted in a Parker 20 Series coupler. **Push-Lok hose barbs are designed for use with Parker push-lok hose and do not require clamps. -7

11 Pneumatics Pneumatic Quick ouplings 6 General Purpose Manual onnect 10 Series, 20 Series, 50 Series, 70 Series omponent Part Features for Manual ouplers, Series 10, 20, 50 & 70 Series 1. Precision machining, hardened wear points* and solid barstock construction provide long life even in rugged applications. 2. Tubular valve with large flow passages delivers high air flow with minimal pressure drop for efficient performance. The tubular design provides 360 support for both the valve seal and the mating nipple for long service life. 3. Precision molded seals form a bubble tight seal for reliable operation within rated working pressures. Standard seal material is Nitrile. Ethylene Propylene, Fluorocarbon and Neoprene seals are available as options. 4. Proven ball locking mechanism with large numbers of hardened steel or stainless steel locking balls evenly distribute the load to resist wear and provide positive connections. The ball locking mechanism also provides accurate alignment and allows a swiveling action to reduce hose torque. 5. Integral sleeve guard protects the sleeve and resists accidental disconnects by allowing the coupling to ride over obstructions without the sleeve being retracted. 6. Knurling and/or grooves on sleeve provide a gripping surface for ease of operation. 7. Wide range of body sizes, materials, options and end terminations are available to meet specific needs. Parker sleeve type couplings are available with male pipe thread, female pipe thread, standard hose barb, Push-Lok hose barb**, and reusable hose fitting ends. Standard body materials are brass in 1/4" body size and steel in larger sizes. 8. Parker sleeve type couplings are available in interchanges for industrial interchange, Tru-flate, RO 210 and Lincoln long stem design nipples. * Steel nipples only. ** Push-lok hose barbs are designed for use with Parker Push-lok hose and do not require clamps. ccessories - oupler Options Grip-Ring Sleeve - Features This Grip-Ring sleeve enables the operator to connect or disconnect the coupling easily, even with greasy hands or while wearing heavy gloves. Grip-Ring sleeves are available for all 10 and 20 Series couplers (only). To specify a model with a Grip-Ring sleeve, add the suffix letter R to the regular model number. Example: 13R. aution: The Grip-Ring sleeve is subject to unintended disconnect if dragged on the end of a hose. o not attempt to pull it over obstacles. Sleeve-Lok - Features ll sizes of 10, 20, 30, 50, and 70 Series couplers (only) can be furnished with Locking Sleeves, as illustrated. Place suffix letters - SL (Sleeve-Lok) after regular catalog number. Example: 13-SL. oupler Repair Kits for 10, 20, 30, 50, 70, & TL Series ody Seal Part Size Material No. 1/4 Nitrile 21K 1/4 Ethylene Propylene 21KW 1/4 Fluorocarbon 21KY 3/8 Nitrile 14K 3/8 Ethylene Propylene 14KW 3/8 Fluorocarbon 14KY 1/2 Nitrile 16K 1/2 Ethylene Propylene 16KW 1/2 Fluorocarbon 16KY 3/4 Nitrile 38K 3/4 Ethylene Propylene 38KW 3/4 Fluorocarbon 38KY -8

12 Pneumatic Quick ouplings General Purpose Manual onnect 10 Series How to Order Information The standard 1/4" 10 Series features a brass coupler with a steel valve. Larger sizes include an all steel construction with brass also available. To order a 3/8" or 1/2" coupler with a brass body and steel sleeve, add the prefix to the steel part number, Example: 15. dd the suffix N as well as the prefix to order an all brass coupler with stainless steel locking balls and springs, Example: 15N. ll-brass couplings should be used to avoid corrosion from moisture. onsult factory for specific recommendations. vailable with Sleeve-Lok (See oupler Options). To order, add the suffix -SL to the part number, Example: 15-SL. vailable for 1/4" 10 Series couplers is a Grip-Ring Sleeve (See oupler Options). To order add the suffix R to the part number, Example: 13R. Pneumatics Features Parker 10 Series couplings are the original Tru-Flate design. This unique design has been field proven as a long lasting, high performance coupling especially when used with pneumatic tools. Standard seals are Nitrile. See the oupling Selection and Ordering Information Guide at the beginning of Section and the Fluid ompatibility hart at the end of this catalog for optional materials. Specifications ody Size (in.) 1/4 3/8 1/2 Rated Pressure (PSI) Temperature Range (Std. seals)* -40 to +250 F. Locking evice 4 balls 8 balls 8 balls Vacuum ata (inches Hg) isconnected (coupler only) Not recommended onnected * See oupling Selection and Ordering Guide for Optional Seals See oupling Repair Kits Table on introduction page to General Purpose - Manual onnect ouplers. Performance ir Flow in SFM Series (1/4", 3/8", 1/2" sizes) 3/8" 1/2" 20 1/4" Pressure rop in PSI 100 PSI Inlet Pressure 80 PSI Inlet Pressure pplications Sleeve type couplings are widely used to connect air lines and can also be used with low pressure fluids. Their compact and economical design uses a ball locking mechanism consisting of captive steel balls that engage the locking groove on the mating nipple. The sliding spring loaded sleeve on the coupler must be manually retracted in order to connect or disconnect the nipple. It is easy to do, but two hands are normally required. ommon applications include: compressed air, water, grease, paint, limited vacuum and limited gases. -9

13 Pneumatics Pneumatic Quick ouplings ouplers Female Pipe Thread General Purpose Manual onnect 10 Series ody Part Part Thread imensions (in.) Size No. No. Size Overall Hex Largest Wt. (L) (in.) rass Steel NPTF Length Size iameter P/Piece 1/4 13 1/ /4 13 1/ /4 13E 3/ /8 15 1/ / / /8 15F 1/ /2 17E 3/ / / /2 17G 3/ Male Pipe Thread ody Part Part Thread imensions (in.) Size No. No. Size Overall Hex Largest Wt. (L) (in.) rass Steel NPTF Length Size iameter P/Piece 1/4 12 1/ /4 12 1/ /4 12E 3/ /8 14 1/ / / /8 14F 1/ /2 16E 3/ / / /2 16G 3/ Standard Hose arb Push-Lok Hose arb* ody Part Part imensions (in.) Size No. No. Hose Overall Hex Largest Wt. (L) (in.) rass Steel I.. Length Size iameter P/Piece 1/ / / / / / / / / / / / / / / / ody Part Part imensions (in.) Size No. No. Hose Overall Hex Largest Wt. (L) (in.) rass Steel I.. Length Size iameter P/Piece 1/4 10-3P - 1/ /4 10-5P - 3/ /8 14-5P 3/ /2 16-5P 3/ /2 16-6P 1/ * Push-Lok hose barbs are designed for use with Parker Push-Lok hose and do not require clamps. -10

14 Pneumatic Quick ouplings Nipples Female Pipe Thread E F G General Purpose Manual onnect 10 Series ody Part Part Thread imensions (in.) Size No. No. Size Overall Exposed Hex Largest Wt. (L) (in.) rass Steel NPTF Length Length* Size iameter P/Piece E F G 1/4 1 1/ / / /4 3-E 3/ /8 1E 1/ /8 3E 3/ /2 1F 3/ /2 3F 1/ /2 H3F-G 3/ Pneumatics Male Pipe Thread E F G * This dimension represents portion of nipple that is exposed when nipple is inserted in a Parker 10 Series coupler. ody Part Part Part No. Thread imensions (in.) Size No. No. Type 303 Size Overall Exposed Hex Largest Wt. (L) (in.) rass Steel Stainless NPTF Length Length* Size iameter P/Piece E F G 1/4 0 1/ /4 2 2 S2 1/ /4 2-E 3/ /8 0E 1/ /8 2E 3/ /2 0F 3/ /2 2F 1/ /2 H2F-G 3/ * This dimension represents portion of nipple that is exposed when nipple is inserted in a Parker 10 Series coupler. Standard Hose arb E Push-Lok Hose arb** E G G ody Part imensions (in.) Size No. Hose Overall Exposed Largest Wt. (L) (in.) Steel I.. Length Length* iameter P/Piece E G 1/4 8 1/ /4 9 3/ /8 5E 3/ /2 H4F 3/ /2 5F 1/ /2 H5F-G 3/ * This dimension represents portion of nipple that is exposed when nipple is inserted in a Parker 10 Series coupler. ody Part imensions (in.) Size No. Hose Overall Exposed Largest Wt. (L) (in.) Steel I.. Length Length* iameter P/Piece E G 1/4 8P 1/ /4 9P 3/ /8 5EP 3/ /2 H4FP 3/ /2 H5FP 1/ * This dimension represents portion of nipple that is exposed when nipple is inserted in a Parker 10 Series coupler. ** Push-Lok hose barbs are designed for use with Parker Push-Lok hose and do not require clamps. -11

15 Pneumatics Pneumatic Quick ouplings Features Parker 20 Series sleeve type couplers accept industrial interchange nipples manufactured by Parker and other manufacturers. Standard seals are Nitrile. See the oupling Selection and Ordering Information Guide at the beginning of Section and the Fluid ompatibility hart at the end of this catalog for optional materials. Specifications General Purpose Manual onnect 20 Series Industrial Interchange How to Order Information The standard 1/4" 20 Series is a brass coupler with a steel valve. The larger sizes are an all steel construction with brass available as an option. To order a 3/8" or 1/2" body size coupler with a brass body and a steel sleeve and valve, add the prefix to the steel part number. Example: 16. dd the suffix N as well as the prefix to order an all brass coupler with stainless steel locking balls and springs, Example: 25N. ll-brass couplings should be used to avoid corrosion from moisture. onsult factory for specific recommendations. vailable with Sleeve-Lok (See oupler Options at the beginning of Section ). To order, add -SL as a suffix to the part number, Example: 25-SL. vailable for 1/4" 20 Series couplers is a Grip-Ring sleeve (See oupler Options). To order, add the suffix R to the part number, Example: 23R. pplications Sleeve type couplings are widely used to connect air lines and can also be used with low pressure fluids. Their compact and economical design uses a ball locking mechanism consisting of captive steel balls that engage the locking groove on the mating nipple. The sliding spring loaded sleeve on the coupler must be manually retracted in order to connect or disconnect the nipple. It is easy to do, but two hands are normally required. ommon applications include: compressed air, water, grease, paint, limited vacuum and limited gases. ody Size (in.) 1/4 3/8 1/2 Rated Pressure (psi) Temperature Range (Std. seals)* -40 to +250 F. Locking evice 4 balls 8 balls 8 balls Vacuum ata (inches Hg) isconnected (coupler only) Not recommended onnected * See oupling Selection and Ordering Guide for Optional Seals See oupling Repair Kits Table on introduction page to General Purpose - Manual onnect ouplers Performance ir Flow in SFM Series (1/4", 3/8", 1/2" sizes) 1/2" 3/8" 1/4" Pressure rop in PSI 100 PSI Inlet Pressure 80 PSI Inlet Pressure -12

16 Pneumatic Quick ouplings ouplers Female Pipe Thread General Purpose Manual onnect 20 Series Industrial Interchange ody Part Part Part No. Thread imension (in.) Size No. No. Type 303 Size Overall Hex Largest Wt. (L) (in.) rass Steel Stainless NPTF Length Size iameter P/Piece 1/4 23 1/ /4 23 S23 1/ /4 23E 3/ /8 25 1/ / / /8 25F 1/ /2 17E 3/ / / /2 17G 3/ Pneumatics Male Pipe Thread ody Part Part Part No. Thread imension (in.) Size No. No. Type 303 Size Overall Hex Largest Wt. (L) (in.) rass Steel Stainless NPTF Length Size iameter P/Piece 1/4 22 1/ /4 22 S22 1/ /4 22E 3/ /8 24 1/ / / /8 24F 1/ /2 16E 3/ / / /2 16G 3/ Standard Hose arb ody Part Part imensions (in.) Size No. No. Hose Overall Hex Largest Wt. (L) (in.) rass Steel I.. Length Size iameter P/Piece 1/ / / / / / / / / / / / / / / / Push-Lok Hose arb* ody Part Part imensions (in.) Size No. No. Hose Overall Hex Largest Wt. (L) (in.) rass Steel I.. Length Size iameter P/Piece 1/4 20-3P 1/ /4 20-5P 3/ /8 24-5P 3/ /2 16-5P 3/ /2 16-6P 1/ * Push-Lok hose barbs are designed for use with Parker Push-Lok hose and do not require clamps. Note: See Table of ontents for those nipples used with 20 Series couplers. -13

17 Pneumatics Pneumatic Quick ouplings General Purpose Manual onnect 50 Series Specifications ody Size (in.) 1/4 Rated Pressure (PSI) 300 Temperature Range (Std. seals)* -40 to +250 F. Locking evice 4 balls * See oupling Selection and Ordering Guide for Optional Seals. See oupling Repair Kits Table on introduction page to General Purpose - Manual onnect ouplers Performance Series (1/4" size) Features Parker 50 Series couplings are interchangeable with RO s 210 series couplings. 50 Series couplings have a full opening tubular valve for maximum flow and a built-in sleeve guard to minimize accidental disconnect. 50 Series couplings have all brass bodies and steel valves. Standard seal material is Nitrile. See the oupling Selection and Ordering Information guide at the beginning of Section and the Fluid ompatibility hart at the end of this catalog for optional materials. Push-to-onnect version available. See H Series. ouplers Female Pipe Thread ir Flow in SFM /4" Pressure rop in PSI 100 PSI Inlet Pressure 80 PSI Inlet Pressure ody Part Thread imensions (in.) Size No. Size Overall Hex Largest Wt. (L) (in.) rass NPTF Length Size iameter P/Piece 1/4 53 1/ /4 53E 3/ Male Pipe Thread ody Part Thread imensions (in.) Size No. Size Overall Hex Largest Wt. (L) (in.) rass NPTF Length Size iameter P/Piece 1/4 52 1/ /4 52E 3/ Push-Lok Hose arb* ody Part imensions (in.) Size No. Hose Overall Hex Largest Wt. (L) (in.) rass I.. Length Size iameter P/Piece 1/4 50-3P 1/ /4 50-5P 3/ * Push-Lok hose barbs are designed for use with Push-Lok hose and do not require clamps. -14

18 Pneumatic Quick ouplings Nipples Female Pipe Thread General Purpose Manual onnect 50 Series Pneumatics E G ody Part Thread imensions (in.) Size No. Size Overall Exposed Hex Largest Wt. (L) (in.) Steel NPTF Length Length* Size iameter P/Piece E F G 1/4 3 1/ F * This dimension represents portion of nipple that is exposed when nipple is inserted in a Parker 50 Series coupler. Male Pipe Thread E G ody Part Thread imensions (in.) Size No. Size Overall Exposed Hex Largest Wt. (L) (in.) Steel NPTF Length Length* Size iameter P/Piece E F G 1/4 2 1/ F * This dimension represents portion of nipple that is exposed when nipple is inserted in a Parker 50 Series coupler. Standard Hose arb E ody Part imensions (in.) Size No. Hose Overall Exposed Largest Wt. (L) (in.) Steel I.. Length Length* iameter P/Piece G E G 1/4 8 1/ * This dimension represents portion of nipple that is exposed when nipple is inserted in a Parker 50 Series coupler. Push-Lok Hose arb** E G ody Part imensions (in.) Size No. Hose Overall Exposed Largest Wt. (L) (in.) Steel I.. Length Length* iameter P/Piece E G 1/4 8P 1/ * This dimension represents portion of nipple that is exposed when nipple is inserted in a Parker 50 Series coupler. ** Push-Lok hose barbs are designed for use with Parker push-lok hose and do not require clamps. -15

19 Pneumatics Pneumatic Quick ouplings General Purpose Manual onnect 70 Series Specifications ody Size (in.) 1/4 Rated Pressure (psi) 300 Temperature Range (Std. seals)* -40 to +250 F. Locking evice Performance 4 balls * See oupling Selection and Ordering Guide for Optional Seals. See oupling Repair Kits Table on introduction page to General Purpose - Manual onnect ouplers Series (1/4" size) 30 Features Parker 70 Series couplings are interchangeable with Lincoln s Long Stem series couplings. 70 Series couplings have a full opening tubular valve for maximum flow and a built-in sleeve guard to minimize accidental disconnect. The 70 Series is only available in 1/4" body size. 70 Series couplings have all brass bodies and steel valves. Standard seal material is Nitrile. See the oupling Selection and Ordering Information Guide at the beginning of Section and the Fluid ompatibility hart at the end of this catalog for optional materials. ouplers Female Pipe Thread Male Pipe Thread Nipples Female Pipe Thread E F G ir Flow in SFM /4" Pressure rop in PSI 100 PSI Inlet Pressure 80 PSI Inlet Pressure ody Part Thread imensions (in.) Size No. Size Overall Hex Largest Wt. (L) (in.) rass NPTF Length Size iameter P/Piece 1/4 73 1/ ody Part Thread imensions (in.) Size No. Size Overall Hex Largest Wt. (L) (in.) rass NPTF Length Size iameter P/Piece 1/4 72 1/ ody Part Thread imensions (in.) Size No. Size Overall Exposed Hex Largest Wt. (L) (in.) Steel NPTF Length Length* Size iameter P/Piece E F G 1/4 L3 1/ Male Pipe Thread E G ody Part Thread imensions (in.) Size No. Size Overall Exposed Hex Largest Wt. (L) (in.) Steel NPTF Length Length* Size iameter P/Piece E F G 1/4 L2 1/ F * This dimension represents portion of nipple that is exposed when nipple is inserted in a Parker 70 Series coupler. -16

20 Pneumatic Quick ouplings 3 General Purpose Push-To-onnect RF, HF, H, U Series Pneumatics omponent Part Features 1. Precision machining, hardened wear points* and solid bar stock construction provide long life even in rugged applications. 2. Tubular valve with large flow passages delivers high flow with minimum pressure drop for efficient performance. The tubular design provides 360 support for both the valve seal and the mating nipple for long service life. 3. Precision molded seals form a bubble tight seal for reliable operation within rated working pressures. Standard seal material is Nitrile. Ethylene Propylene, Fluorocarbon and Neoprene are available as options. See the oupling Selection and Ordering Guide in the front of the Pneumatic Section of the catalog. 4. Proven ball locking mechanism with large numbers of hardened steel or stainless steel locking balls evenly distribute the load to resist wear and provide positive connections. The ball locking mechanism also provides accurate alignment and allows a swiveling action to reduce hose torque. 5. Integral sleeve guard protects the sleeve and resists accidental disconnects by allowing the coupling to ride over obstructions without the sleeve being retracted. 6. Knurling on the sleeve provides a gripping surface for ease of operation. 7. Wide range of end configurations are available to meet specific needs. Parker push-to-connect type couplings are available with male pipe thread, female pipe thread, standard hose barb, and Push-Lok hose barb**. 8. Parker 20, 30, HF, and E-z-mate Series couplings mate with industrial interchange design nipples. See Table of ontents for additional specifications. 9. Push-to-connect design permits one-handed connection when the coupler half is rigidly mounted. * steel nipples only ** Push-Lok hose barbs are designed for use with Parker Push-Lok hose and do not require clamps. -17

21 Pneumatics Pneumatic Quick ouplings General Purpose Push-To-onnect RF Series escription The Parker RF Series pneumatic couplings offer the quality and dependability customers have come to expect from Parker s line of pneumatic quick couplings. The RF Series has been designed to increase the flow through and reduce the pressure drop over the coupling. The nipple design has up to 2-1/2 times larger flow area than standard industrial interchange nipples. This, along with a specially designed coupler valve, allows tremendous flow through a coupling with an envelope size of current couplings in the market today. The benefits to the end user are increased tool efficiency and decreased air costs. Performance RF Series (1/4" & 3/8" body size) with 1/4" & 3/8" Female NPSF 160 Features erodynamic valve design. Flow area of the RF nipple is up to 2-1/2 times larger than industrial interchange nipples. Flow rates on 1/4 greater than many 3/8" body size couplers. Flow rates on 3/8 greater than many 1/2" body size couplers. oupler sleeves are nickel-plated steel and coupler bodies are solid brass construction for excellent corrosion resistance. Standard RF nipples are manufactured from solid steel bar stock, case hardened and hromium-6 Free plated. ependable ball locking mechanism allows a swiveling action to reduce hose torque. Push-To-onnect design for easy one hand connection. Integral sleeve guard to protect against accidental disconnection. Wide range of port options available. More efficient use of compressed air due to higher flows and reduced pressure drop. 1/4 body size interchanges with Rectus 25 and ejn 320 series. 3/8 body size interchanges with Rectus 27 and ejn 410 series. Specifications ody Size (in.) 1/4 3/8 Rated Pressure (psi) Temperature Range (std seals) -40 to +250 F -40 to +250 F Locking evice 4 balls 8 balls Vacuum ata (inches Hg) isconnected (coupler only) Not Recommended Not Recommended onnected Not Recommended Not Recommended ir Flow in SFM /8" ody Size 3/8" Female NPSF How To Order RF FP - * 1/4" ody Size 3/8" Female NPSF 1/4" ody Size 1/4" Female NPSF Pressure rop in PSI 100 PSI Inlet Pressure 80 PSI Inlet Pressure Seal Options lank - Nitrile F - Fluorocarbon E - Ethylene Propylene Port onfiguration FP - Female Pipe MP - Male Pipe H - Standard Hose arb PL - Push-Lok Hose arb Port Size (1/16 of an inch) Unit 1 - Valved oupler 4 - Unvalved Nipple ody Size 25-1/4" 37-3/8" RF Series -18

22 Pneumatic Quick ouplings ouplers Female Pipe Thread General Purpose Push-To-onnect RF Series Pneumatics ody NEW OL Thread imensions (in.) Size Part Part Size Overall Hex Largest Wt. (L) (in.) No. No. NPSF Length Size iameter P/Piece 1/4 RF-251-4FP RF / /4 RF-251-6FP RF / /8 RF-371-6FP 3/ /8 RF-371-8FP 1/ Male Pipe Thread ody NEW OL Thread imensions (in.) Size Part Part Size Overall Hex Largest Wt. (L) (in.) No. No. NPTF Length Size iameter P/Piece 1/4 RF-251-4MP RF / /4 RF-251-6MP RF / /4 RF-251-8MP RF / /8 RF-371-6MP 3/ /8 RF-371-8MP 1/ Standard Hose arb ody NEW OL imensions (in.) Size Part Part Hose Overall Hex Largest Wt. (L) (in.) No. No. I.. Length Size iameter P/Piece 1/4 RF-251-4H RFH-4-4 1/ /4 RF-251-6H RFH-4-6 3/ /8 RF-371-6H 3/ /8 RF-371-8H 1/ Push-Lok Hose arb ody NEW OL imensions (in.) Size Part Part Hose Overall Hex Largest Wt. (L) (in.) No. No. I.. Length Size iameter P/Piece 1/4 RF-251-4PL RFPL-4-4 1/ /4 RF-251-6PL RFPL-4-6 3/ /4 RF-251-8PL RFPL-4-8 1/ /8 RF-371-6PL 3/ /8 RF-371-8PL 1/

23 Pneumatics Pneumatic Quick ouplings Nipples Female Pipe Thread Male Pipe Thread General Purpose Push-To-onnect RF Series ody NEW OL Thread imensions (in.) Size Part Part Size Overall Exposed* Hex Largest Wt. (L) (in.) No. No. NPTF Length Length Size iameter P/Piece E F G 1/4 RF-254-4FP NRF S 1/ /4 RF-254-6FP NRF S 3/ /8 RF-374-6FP 3/ /8 RF-374-8FP 1/ ody NEW OL Thread imensions (in.) Size Part Part Size Overall Exposed* Hex Largest Wt. (L) (in.) No. No. NPTF Length Length Size iameter P/Piece E F G 1/4 RF-254-4MP NRF S 1/ /4 RF-254-6MP NRF S 3/ /8 RF-374-6MP 3/ /8 RF-374-8MP 1/ Standard Hose arb ody NEW OL imensions (in.) Size Part Part Hose Overall Exposed* Largest Wt. (L) (in.) No. No. I.. Length Length iameter P/Piece E G 1/4 RF-254-4H NRFH-4-4-S 1/ /4 RF-254-6H NRFH-4-6-S 3/ /8 RF-374-6H 3/ /8 RF-374-8H 1/ Push-Lok Hose arb ody NEW OL imensions (in.) Size Part Part Hose Overall Exposed* Largest Wt. (L) (in.) No. No. I.. Length Length iameter P/Piece E G 1/4 RF-254-4PL NRFPL-4-4-S 1/ /4 RF-254-6PL NRFPL-4-6-S 3/ /8 RF-374-6PL 3/ /8 RF-374-8PL 1/ * This dimension represents portion of nipple that is exposed when nipple is inserted in a Parker RF Series coupler. -20

24 Pneumatic Quick ouplings General Purpose Push-To-onnect HF Series Industrial Interchange Specifications ody Size (in.) 1/8 1/4 3/8 1/2 Rated Pressure (psi) Temperature Range (Std. seals) -40 to +250 F Locking evice 5 balls 4 balls 6 balls 8 balls Vacuum ata (inches Hg) isconnected (coupler only) Not Recommended onnected Pneumatics Performance 40 HF Series (1/8" & 1/4" sizes) 35 Features Parker HF Series Pneumatic Quick ouplings offer an alternative to traditional industrial interchange couplers. The quality and durability you have come to expect from Parker 20 Series couplers, combined with a slim profile and pushto-connect design. The result is an easy to use general purpose pneumatic coupler suitable for use in a variety of applications. Parker HF couplers feature sleeve guards** to protect against accidental disconnection. Standard couplers feature solid brass construction, high flow valving, corrosion resistant valves, and stainless steel locking balls and valve spring. Heavy uty ouplers* featuring heat treated, solid steel bodies and sleeves for added strength and durability. Parker HF couplers accept Industrial Interchange nipples*** manufactured by Parker and other manufacturers. See table of contents. *** 1/8" couplings have no standard industry interface. ** 1/8" couplings do not incorporate an integral sleeve guard. * 1/8 and 1/2 are unavailable in the Heavy uty version. How To Order HF FP - * - S Heavy uty Steel oupler Seal Options lank - Nitrile F - Fluorocarbon E - Ethylene Propylene Port onfiguration FP - Female Pipe MP - Male Pipe H - Standard Hose arb PL - Push-Lok Hose arb Port Size (1/16 of an inch) Unit 1 - Valved oupler 4 - Unvalved Nipple ody Size 12-1/8" 25-1/4" 37-3/8" 50-1/2" HF Series ir Flow in SFM ir Flow in SFM /4" 1/8" Pressure rop in PSI 100 PSI Inlet Pressure 80 PSI Inlet Pressure HF Series (3/8" & 1/2" sizes) 1/2" 3/8" Pressure rop in PSI 100 PSI Inlet Pressure 80 PSI Inlet Pressure -21

25 Pneumatics Pneumatic Quick ouplings 1/8" ody Size ouplers Female Pipe Thread General Purpose Push-To-onnect HF Series Industrial Interchange ody New Old Thread imensions (in.) Size Part No. Part No. Size Overall Hex Largest Wt. (L) (in.) rass rass NPTF Length Size iameter P/Piece 1/8 HF-121-2FP HF302F-2 1/ /8 HF-121-4FP HF302F-4 1/ Male Pipe Thread ody New Old Thread imensions (in.) Size Part No. Part No. Size Overall Hex Largest Wt. (L) (in.) rass rass NPTF Length Size iameter P/Piece 1/8 HF-121-2MP HF302M-2 1/ /8 HF-121-4MP HF302M-4 1/ /8" ody Size Nipples Female Pipe Thread E G ody New Old Thread imensions (in.) Size Part No. Part No. Size Overall Exposed Hex Largest Wt. (L) (in.) rass rass NPTF Length Length* Size iameter P/Piece E F G 1/8 HF-124-2FP HF702F-2 1/ /8 HF-124-4FP HF702F-4 1/ * This dimension represents the portion that is exposed when nipple is inserted in a Parker HF series coupler. F Male Pipe Thread E G ody New Old Thread imensions (in.) Size Part No. Part No. Size Overall Exposed Hex Largest Wt. (L) (in.) rass rass NPTF Length Length* Size iameter P/Piece E F G 1/8 HF-124-2MP HF702M-2 1/ /8 HF-124-4MP HF702M-4 1/ F * This dimension represents the portion that is exposed when nipple is inserted in a Parker HF series coupler. -22

26 Pneumatic Quick ouplings 1/4, 3/8, & 1/2 ody Size ouplers Female Pipe Thread General Purpose Push-To-onnect HF Series Industrial Interchange ody New Old Thread imensions (in.) Size Part No. Part No. Size Overall Hex Largest Wt. (L) (in.) rass rass NPSF Length Size iameter P/Piece 1/4 HF-251-4FP HF304F-4 1/ /4 HF-251-6FP HF304F-6 3/ /8 HF-371-4FP HF306F-4 1/ /8 HF-371-6FP HF306F-6 3/ /8 HF-371-8FP HF306F-8 1/ /2 HF-501-8FP 1/ Pneumatics Male Pipe Thread ody New Old Thread imensions (in.) Size Part No. Part No. Size Overall Hex Largest Wt. (L) (in.) rass rass NPTF Length Size iameter P/Piece 1/4 HF-251-4MP HF304M-4 1/ /4 HF-251-6MP HF304M-6 3/ /8 HF-371-4MP HF306M-4 1/ /8 HF-371-6MP HF306M-6 3/ /8 HF-371-8MP HF306M-8 1/ /2 HF-501-8MP 1/ Standard Hose arb ody New Old imensions (in.) Size Part No. Part No. Hose Overall Hex Largest Wt. (L) (in.) rass rass I.. Length Size iameter P/Piece 1/4 HF-251-4H HF304H-4 1/ /4 HF-251-6H HF304H-6 3/ /8 HF-371-6H HF306H-6 3/ /8 HF-371-8H HF306H-8 1/ Push-Lok Hose arb ody New Old imensions (in.) Size Part No. Part No. Hose Overall Hex Largest Wt. (L) (in.) rass rass I.. Length Size iameterp/piece 1/4 HF-251-4PL HF304PL-4 1/ /4 HF-251-6PL HF304PL-6 3/ /8 HF-371-6PL HF306PL-6 3/ /8 HF-371-8PL HF306PL-8 1/

27 Pneumatics Pneumatic Quick ouplings Heavy uty ouplers Female Pipe Thread General Purpose Push-To-onnect HF Series Industrial Interchange ody New Old Thread imensions (in.) Size Part No. Part No. Size Overall Hex Largest Wt. (L) (in.) Steel Steel NPSF Length Size iameter P/Piece 1/4 HF-251-4FP-S HF404F-4 1/ /4 HF-251-6FP-S HF404F-6 3/ /8 HF-371-4FP-S HF406F-4 1/ /8 HF-371-6FP-S HF406F-6 3/ /8 HF-371-8FP-S HF406F-8 1/ Male Pipe Thread ody New Old Thread imensions (in.) Size Part No. Part No. Size Overall Hex Largest Wt. (L) (in.) Steel Steel NPTF Length Size iameter P/Piece 1/4 HF-251-4MP-S HF404M-4 1/ /4 HF-251-6MP-S HF404M-6 3/ /8 HF-371-4MP-S HF406M-4 1/ /8 HF-371-6MP-S HF406M-6 3/ /8 HF-371-8MP-S HF406M-8 1/ Standard Hose arb ody New Old imensions (in.) Size Part No. Part No. Hose Overall Hex Largest Wt. (L) (in.) Steel Steel I.. Length Size iameter P/Piece 1/4 HF-251-4H-S HF404H-4 1/ /4 HF-251-6H-S HF404H-6 3/ /8 HF-371-6H-S HF406H-6 3/ /8 HF-371-8H-S HF406H-8 1/ Push-Lok Hose arb ody New Old imensions (in.) Size Part No. Part No. Hose Overall Hex Largest Wt. (L) (in.) Steel Steel I.. Length Size iameter P/Piece 1/4 HF-251-4PL-S HF404PL-4 1/ /4 HF-251-6PL-S HF404PL-6 3/ /8 HF-371-6PL-S HF406PL-6 3/ /8 HF-371-8PL-S HF406PL-8 1/

28 Pneumatic Quick ouplings General Purpose Push-To-onnect H Series Specifications ody Size (in.) 1/4 Rated Pressure (psi) 300 Temperature Range (Std. seals) Locking evice Vacuum Service -40 to +250 F 4 balls Not Recommended Pneumatics Performance H Series (1/4" size) Features Parker H Series couplings are interchangeable with RO's 210 series couplings. See Table of ontents. Push to onnect design for easy one hand operation. H Series couplings utilize a tubular valve for maximum flow and a built-in sleeve guard to minimize accidental disconnect. The H Series is only available in 1/4" body size. H Series couplings have all brass bodies. Standard seal material is Nitrile. See the oupling Selection and Ordering Information Guide at the beginning of Section and the Fluid ompatibility hart at the end of this catalog for optional materials. Other port options available contact the division. Formerly the 50 Series. ouplers Female Pipe Thread ir Flow in SFM /4" How To Order H FP - * Pressure rop in PSI 100 PSI Inlet Pressure 80 PSI Inlet Pressure Seal Options lank - Nitrile F - Fluorocarbon E - Ethylene Propylene Port onfiguration FP - Female Pipe MP - Male Pipe Port Size (1/16 of an inch) Unit 1 - Valved oupler ody Size 25-1/4" H Series ody NEW OL Thread imensions (in.) Size Part No. Part No. Size Overall Hex Largest Wt. (L) (in.) rass rass NPSF Length Size iameter P/Piece 1/4 H-251-4FP / Male Pipe Thread ody NEW OL Thread imensions (in.) Size Part No. Part No. Size Overall Hex Largest Wt. (L) (in.) rass rass NPSF Length Size iameter P/Piece 1/4 H-251-4MP / * See page -15 for Nipples -25

29 Pneumatics Pneumatic Quick ouplings Specifications ody Size (in.) 1/4 Rated Pressure (PSI) 150 Temperature Range (Nitrile seal) -40 to +250 F. Locking evice 4 balls Vacuum Service Not Recommended How to Order U FP - * Seal Options lank - Nitrile F - Fluorocarbon E - Ethylene Propylene Port onfiguration FP - Female Pipe MP - Male Pipe H - Standard Hose arb* PL - Push-Lok Hose arb* Port Size (1/16 of an inch) Unit 1 - Valved oupler ody Size 25-1/4" U Series * ontact the ivision for availability General Purpose Push-To-onnect U Series Features The 1/4" U Series oupler will accept the industrial interchange, [(MIL--4109F) and (NSI/(NFP) T )], 10 Series (Tru-Flate) and the 50 series (RO 210) style nipples. The coupler features automatic push-to-connect operation, high flow machined window valve, corrosion resistant solid brass construction and a sleeve guard which helps prevent accidental disconnects and protects the sleeve from damage. While the best quick coupling performance is obtained by matching like series couplers and nipples, the universal coupler permits multiple series nipples to mate with one coupler. Performance ir Flow in SFM U Series oupler (1/4" size) 1/4" Pressure rop in PSI 100 PSI Inlet Pressure 80 PSI Inlet Pressure ouplers Female Pipe Thread ody New Old Thread imensions (in.) Size Part No. Pat No. Size Overall Hex Largest Wt. (L) (in.) rass rass NPSF Length Size iameter P/Piece 1/4 U-251-4FP U304F-4 1/ /4 U-251-6FP U304F-6 3/ Male Pipe Thread ody New Old Thread imensions (in.) Size Part No. Part No. Size Overall Hex Largest Wt. (L) (in.) rass rass NPTF Length Size iameter P/Piece 1/4 U-251-4MP U304M-4 1/ /4 U-251-6MP U304M-6 3/ ontact the ivision for Hose arb and Push-Lok port availability -26

30 Pneumatic Quick ouplings 7 General Purpose Push-To-onnect 30 Series Industrial Interchange 6 Pneumatics omponent Part Features 1. Precision machining, hardened wear points* and solid bar stock construction provide long life even in rugged applications. 2. Tubular valve with large flow passages delivers high flow with minimum pressure drop for efficient performance. The tubular design provides 360 support for both the valve seal and the mating nipple for long service life. 3. Precision molded seals form a bubble tight seal for reliable operation within rated working pressures. Standard seal material is Nitrile. Ethylene Propylene, Fluorocarbon and Neoprene are available as options. 4. Locking pawls (pins) constructed of stainless steel create a durable locking mechanism that provides alignment and evenly distributes loads. 5. Push-to-connect design permits one-handed connection when the coupler half is rigidly mounted. 6. Knurling on the sleeve provides a gripping surface for ease of operation. 7. Wide range of end terminations are available to meet specific needs. Parker push type couplings are available with male pipe thread, female pipe thread, standard hose barb, and Push-Lok hose barb**. 8. Parker 30 Series couplings mate with industrial interchange design nipples. See Table of ontents. * steel nipples only ** Push-Lok hose barbs are designed for use with Parker Push-Lok hose and do not require clamps. -27

31 Pneumatics Pneumatic Quick ouplings Features Parker 30 Series couplers are designed for rigid mounting that allows a simple push-to-connect operation. onstructed of a solid brass body and a steel valve, 30 Series couplers are noted for their high flow capability, reliability and rugged design. Parker 30 Series couplers accept industrial interchange nipples manufactured by Parker and other manufacturers. Standard seal material is Nitrile. See Ordering Information at the beginning of Section and the Fluid ompatibility hart at the end of this catalog for optional materials. Specifications ody Size (in.) 1/4 3/8 1/2 3/4 Rated Pressure (PSI) Temperature Range (Std. seals)* -40 to +250 F. Locking evice 3 pawls 4 pawls 5 pawls 6 pawls Vacuum ata (inches Hg) isconnected (coupler only) Not recommended onnected * See oupling Selection and Ordering Guide for Optional Seals. Repair Kits ody Seal Part Size Material No. 1/4 Nitrile 21K 1/4 Ethylene Propylene 21KW 1/4 Fluorocarbon 21KY 3/8 Nitrile 14K 3/8 Ethylene Propylene 14KW 3/8 Fluorocarbon 14KY 1/2 Nitrile 16K 1/2 Ethylene Propylene 16KW 1/2 Fluorocarbon 16KY 3/4 Nitrile 38K 3/4 Ethylene Propylene 38KW 3/4 Fluorocarbon 38KY General Purpose Push-To-onnect 30 Series Industrial Interchange How to Order Information vailable with Sleeve-Lok (See oupler Options Section). To order, add the suffix -SL to part number, Example: 33-SL. rass valves are available for extra corrosion resistance. To specify a brass valve, add the suffix N to the regular part number. Example: 33N. brass valve should be used for corrosive applications where steel parts are not suitable. onsult the factory for specific recommendations. Operation Push type couplings feature one handed automatic connection by pushing the nipple into the coupler provided the coupler half is firmly mounted. The locking mechanism of Parker 30 Series couplers consists of pawls (or pins) which act directly on the sleeve, thereby causing the sleeve to automatically retract when the mating nipple is inserted. Sleeve must be manually retracted to remove the nipple. 30 Series couplings are push type Single Shut-Off couplings. Performance ir Flow in SFM ir Flow in SFM Series (1/4" & 3/8" sizes) Pressure rop in PSI 100 PSI Inlet Pressure 80 PSI Inlet Pressure 30 Series (1/2" & 3/4" sizes) 3/4" 1/4" 1/2" 3/8" Pressure rop in PSI 100 PSI Inlet Pressure 80 PSI Inlet Pressure -28

32 Pneumatic Quick ouplings ouplers Female Pipe Thread General Purpose Push-To-onnect 30 Series Industrial Interchange ody Part Thread imensions (in.) Size No. Size Overall Hex Largest Wt. (L) (in.) rass NPTF Length Size iameter P/Piece 1/4 33 1/ /4 33 1/ /4 33E 3/ /8 35 1/ /8 35 3/ /8 35F 1/ /2 37E 3/ /2 37 1/ /2 37G 3/ /4 39F 1/ /4 39 3/ /4 39J / Pneumatics Male Pipe Thread ody Part Thread imensions (in.) Size No. Size Overall Hex Largest Wt. (L) (in.) rass NPTF Length Size iameter P/Piece 1/4 32 1/ /4 32 1/ /4 32E 3/ /8 34 1/ /8 34 3/ /8 34F 1/ /2 36E 3/ /2 36 1/ /2 36G 3/ /4 38 3/ /4 38J /

33 Pneumatics Pneumatic Quick ouplings ouplers Standard Hose arb General Purpose Push-To-onnect 30 Series Industrial Interchange ody Part imensions (in.) Size No. Hose Overall Hex Largest Wt. (L) (in.) rass I.. Length Size iameter P/Piece 1/ / / / / / / / / / / / / / / / / Push-Lok Hose arb* ody Part imensions (in.) Size No. Hose Overall Hex Largest Wt. (L) (in.) rass I.. Length Size iameter P/Piece 1/4 30-3P 1/ /4 30-5P 3/ /8 34-5P 3/ /2 36-6P 1/ * Push-Lok hose barbs are designed for use with Parker Push-Lok hose and do not require clamps. -30

34 Pneumatic Quick ouplings General Purpose Push-To-onnect Twist-Lock Specification ody Size (in.) 1/4 1/2 Rated Pressure (PSI) Temperature Range (Nitrile seal) -40 F to +250 F. Locking evice M Vacuum Service Not Recommended Pneumatics Performance 35 Twist-Lock Series (1/4" size) 30 Features Push-to-onnect design for easy one hand operation. variety of port configurations are available to meet specific needs. Standard Seals are Nitrile. Zinc bodies with hromium-6 Free plated steel sleeves and nipples. Interchanges with Schrader Twist-Lock style couplings. Operation Engineered for speedy coupling and uncoupling. To lock push in; to unlock give the coupler sleeve a 1/8 turn. esigned to protect against accidental uncoupling. ir Flow in SFM /4" Pressure rop in PSI 100 PSI Inlet Pressure 80 PSI Inlet Pressure How To Order TL-251-4FP TL Series Port onfiguration FP - Female Pipe MP - Male Pipe H - Standard Hose arb PL - Push-Lok Hose arb Port Size (1/16 of an inch) Unit 1 - Valved oupler 4 - Unvalved Nipple ody Size 25-1/4" 50-1/2" -31

35 Pneumatics Pneumatic Quick ouplings ouplers Female Thread General Purpose Push-To-onnect Twist-Lock Male Thread ody NEW OL Thread imensions (in.) Size Part No. Part No. Size Overall Hex Largest Wt. (L) (in.) Steel Steel NPT Length Size iameter P/Piece 1/4 TL-251-4FP / /2 TL-501-6FP / /2 TL-501-8FP / /2 TL FP / ody NEW OL Thread imensions (in.) Size Part No. Part No. Size Overall Hex Largest Wt. (L) (in.) Steel Steel NPT Length Size iameter P/Piece 1/4 TL-251-4MP / /4 TL-251-6MP / /2 TL-501-6MP / /2 TL-501-8MP / Nipples Female Thread ody NEW OL Thread imensions (in.) Size Part No. Part No. Size Overall Hex Largest Wt. (L) (in.) Steel Steel NPT Length Size iameter P/Piece E F E F 1/4 TL-254-2FP / /4 TL-254-4FP / /2 TL-504-4FP / /2 TL-504-6FP / Male Thread E F ody NEW OL Thread imensions (in.) Size Part No. Part No. Size Overall Hex Largest Wt. (L) (in.) Steel Steel NPT Length Size iameter P/Piece E F 1/4 TL-254-2MP / /4 TL-254-4MP / /2 TL-504-4MP / /2 TL-504-6MP / /2 TL-504-8MP / /2 TL MP / Standard Hose arb ody NEW OL Thread imensions (in.) Size Part No. Part No. Size Overall Largest Wt. (L) (in.) Steel Steel NPT Length iameter P/Piece F F 1/4 TL-254-4H / /4 TL-254-6H / /2 TL-504-4H / /2 TL-504-6H / /2 TL-504-8H /

36 Pneumatic Quick ouplings Special Purpose Standard - Non Marring Tool-Mate Series Features Standard style Tool-Mate couplers are lightweight, easy to operate, and non-marring with easy, push-to-connect action. ouplers are constructed of Polyamide material; springs, balls, and pins are stainless steel; and locking fingers are made of polyacetate. PH Tool-Mate Series is built to the Industrial Interchange profile identifiable with a Yellow ring around the body. PER Tool-Mate Series is designed to use with Parker's high flow RF Series nipples and is indentifiable with a Green ring around the body. Grey body designates standard non-venting style coupler. Pneumatics Operation Push-to-onnect design for easy one hand operation. Pull in the direction of the arrow indicated on the body of the coupler to release the nipple. Specifications ody Size 1/4 3/8 Rated Pressure Temperature Range ( F) 0 to to 160 Vacuum Service Not Recommended How To Order Performance PH FP Port onfiguration FP - Female Pipe MP - Male Pipe Port Size (1/16 of an inch) 4-1/4 6-3/8 8-1/2 Unit 1 - Valved oupler ody Size 25-1/4 37-3/8 Tool-Mate Series (Non-venting) PH - Industrial Interchange PER - RF Interchange ir Flow in SFM Tool-Mate Series Standard (1/4 & 3/8 sizes) 3/8" PH 1/4" PER 1/4" PH Pressure rop in PSI 100 PSI Inlet Pressure -33

37 Pneumatics Pneumatic Quick ouplings Industrial Interchange Special Purpose Standard - Non Marring Tool-Mate Series Female Pipe Thread ody Size (in.) Part No. Thread Size NPTF Overall Length Hex Size Largest iameter Wt. (L) P/Piece 1/4" 1/4" 3/8" 3/8" 3/8" PH-251-4FP PH-251-6FP PH-371-4FP PH-371-6FP PH-371-8FP 1/4-18 3/8-18 1/4-18 3/8-18 1/ Male Pipe Thread ody Size (in.) Part No. Thread Size NPTF Overall Length Hex Size Largest iameter Wt. (L) P/Piece 1/4" 1/4" 3/8" 3/8" PH-251-4MP PH-251-6MP PH-371-4MP PH-371-6MP 1/4-18 3/8-18 1/4-18 3/ RF Interchange Female Pipe Thread ody Size (in.) Part No. Thread Size NPTF Overall Length Hex Size Largest iameter Wt. (L) P/Piece 1/4" 1/4" PER-251-4FP PER-251-6FP 1/4-18 3/ Male Pipe Thread ody Size (in.) Part No. Thread Size NPTF Overall Length Hex Size Largest iameter Wt. (L) P/Piece 1/4" 1/4" PER-251-4MP PER-251-6MP 1/4-18 3/

38 Pneumatic Quick ouplings Special Purpose Exhaust - Non Marring Tool-Mate Series Features Exhaust style Tool-Mate couplers are lightweight, easy to operate, and non-marring with easy, push-to-connect action and one-handed disconnection. ouplers are constructed of black Polyamide material; springs, balls, and pins are stainless steel in the PES series and 1/2" PS series; and locking fingers in the PS series are made of polyacetate. End ports are galvanized steel. PS Tool-Mate Series is built to the Industrial Interchange profile identifiable with a Yellow ring around the body. PES Tool-Mate Series is designed for use with high flow RF Series nipples and is identifiable with a Green ring around the body. Exhaust style Tool-Mate couplers meet the ISO 4414 specification to allow trapped air pressure to be vented prior to disconnection. lack body designates exhaust style coupler. Pneumatics Specifications ody Size 1/4 3/8 1/2 Rated Pressure Temperature Range ( F) 0 to to to 160 Vacuum Service Not Recommended Operation Push-to-onnect design for easy one hand operation. Pull the body in the direction of the arrow marked 1, this will safely vent the downstream pressure. Push the body in the direction of arrow 2 to disconnect at 0 pressure. How To Order PS FP Port onfiguration FP - Female Pipe MP - Male Pipe Port Size (1/16 of an inch) 4-1/4 6-3/8 8-1/2 12-3/4 Unit 1 - Valved oupler ody Size 25-1/4 37-3/8 50-1/2 Tool-Mate Series (Exhaust) PS - Industrial Interchange PES - RF Interchange ir Flow in SFM Performance Tool-Mate Series Exhaust (1/4, 3/8 & 1/2 sizes) /2" PS /8" PS 1/4" PES /4" PS Pressure rop in PSI 100 PSI Inlet Pressure -35

39 Pneumatics Pneumatic Quick ouplings Exhaust Industrial Interchange Special Purpose Exhaust - Non Marring Tool-Mate Series Female Pipe Thread ody Size (in.) Part No Thread Size NPTF Overall Length Hex Size Largest iameter Wt. (L) P/Piece 1/4" 1/4" 3/8" 3/8" 1/2" 1/2" 1/2" PS-251-4FP PS-251-6FP PS-371-6FP PS-371-8FP PS-501-6FP PS-501-8FP PS FP 1/4-18 3/8-18 3/8-18 1/2-14 3/8-18 1/2-14 3/ Male Pipe Thread ody Size (in.) Part No. Thread Size NPTF Overall Length Hex Size Largest iameter Wt. (L) P/Piece 1/4" 1/4" 3/8" 3/8" 1/2" PS-251-4MP PS-251-6MP PS-371-6MP PS-371-8MP PS-501-8MP 1/4-18 3/8-18 3/8-18 1/2-18 1/ Exhaust RF Interchange Female Pipe Thread ody Size (in.) Part No. Thread Size NPTF Overall Length Hex Size Largest iameter Wt. (L) P/Piece 1/4" PES-251-6FP 3/ Male Pipe Thread ody Size (in.) Part No. Thread Size NPTF Overall Length Hex Size Largest iameter Wt. (L) P/Piece 1/4" PES-251-4MP 1/

40 Pneumatic Quick ouplings Operation Parker E-z-mate couplings combine push-to-connect, exhaust-style action with a self-locking valve sleeve to guard against accidental disconnection. Simply follow the direction of the On-Off arrow stamped on the yellow chromate valve sleeve. It s that easy. To connect, push the nipple into the coupler. The black locking sleeve automatically slides forward securely locking the nipple in place. No air is allowed to flow through the coupling at this point. The yellow chromate valve sleeve is then rotated clockwise (when viewed from the coupler port end) to open flow and automatically engage the sleeve-lock mechanism. To disconnect, rotate the valve sleeve counter clockwise (when viewed from the coupler end). The flow of air through the coupling will be shut off and all downstream air is vented to the atmosphere. The locking sleeve may now be retracted and the nipple removed. Lubricate sleeve as part of periodic maintenance to coupler. Specifications ody Size (in.) 1/4 3/8 1/2 3/4 Rated Pressure (PSI) Temperature Range (std seals) -40 to +250 F. Locking evice 4 balls 4 balls 6 balls 8 balls Force required to onnect (lbs) Less than 10 Vacuum Service Not recommended How To Order EZ FP Port onfiguration FP - Female Pipe MP - Male Pipe H - Standard Hose arb PL - Push-Lok Hose arb Port Size (1/16 of an inch) Unit 1 - Valved oupler 4 - Unvalved Nipple ody Size 25-1/4" 37-3/8" 50-1/2" 75-3/4" E-z-mate Series Special Purpose Exhaust - Steel E-z-mate Series Industrial Interchange Features Parker's E-z-mate is an exhaust type coupler that is designed to exhaust air pressure prior to the disconnection process. The valve sleeve acts as an integral shut-off valve that allows connection and disconnection at zero pressure. When the sleeve is moved to shut off air flow, it automatically vents downstream allowing for disconnection at zero pressure and eliminating the risk of hose whip. Meets ISO 4414 requirements for a controlled pressure release system. uilt-in sleeve-lok mechanically locks the valve sleeve to help prevent accidental disconnects. Proven ball locking mechanism evenly distributes load to resist wear and provide positive connections. The ball locking mechanism also provides accurate alignment and allows a swiveling action to reduce hose torque. O-ring interface seal assures bubble tight seal and long service life. E-z-mate Series couplers use industrial interchange nipples. rass versions available. ontact the division for availability. Performance ir Flow in SFM ir Flow in SFM E-z-mate Series (1/4" & 3/8" sizes) Pressure rop in PSI 100 PSI Inlet Pressure 80 PSI Inlet Pressure E-z-mate Series (1/2" & 3/4" sizes) 3/4" 3/8" 1/2" 1/4" Pressure rop in PSI Pneumatics PSI Inlet Pressure 80 PSI Inlet Pressure

41 Pneumatics Pneumatic Quick ouplings ouplers Female Pipe Thread OFF ON Special Purpose Exhaust - Steel E-z-mate Series Industrial Interchange ody New Old Thread imensions (in.) Size Part No. Part No. Size Overall Hex Largest Wt. (L) (in.) Steel Steel NPTF Length Size iameter P/Piece 1/4 EZ-251-4FP EZ304F-4T 1/ /4 EZ-251-6FP EZ304F-6T 3/ /8 EZ-371-6FP EZ306F-6T 3/ /8 EZ-371-8FP EZ306F-8T 1/ /2 EZ-501-8FP EZ308F-8T 1/ /2 EZ FP EZ308F-12T 3/ /4 EZ FP EZ312F-12T 3/ /4 EZ FP EZ312F-16T / Male Pipe Thread OFF ON ody New Part Thread imensions (in.) Size Part No. No. Size Overall Hex Largest Wt. (L) (in.) Steel Steel NPTF Length Size iameter P/Piece 1/4 EZ-251-4MP EZ304M-4T 1/ /4 EZ-251-6MP EZ304M-6T 3/ /8 EZ-371-6MP EZ306M-6T 3/ /2 EZ-501-8MP EZ308M-8T 1/ /4 EZ MP EZ312M-12T 3/ Standard Hose arb OFF ON ody New Old imensions (in.) Size Part No. Part No. Hose Overall Hex Largest Wt. (L) (in.) Steel Steel I.. Length Size iameter P/Piece 1/4 EZ-251-4H EZ304H-4T 1/ /4 EZ-251-6H EZ304H-6T 3/ /8 EZ-371-6H EZ306H-6T 3/ /2 EZ-501-8H EZ308H-8T 1/ Push-Lok Hose arb* OFF ON ody New Old imensions (in.) Size Part No. Part No. Hose Overall Hex Largest Wt. (L) (in.) Steel Steel I.. Length Size iameter P/Piece 1/4 EZ-251-4PL EZ304PL-4T 1/ /4 EZ-251-6PL EZ304PL-6T 3/ /8 EZ-371-6PL EZ306PL-6T 3/ /2 EZ-501-8PL EZ308PL-8T 1/ * Push-Lok hose barbs are designed for use with Parker Push-Lok hose and do not require clamps. Note: See Table of ontents for Industrial Interchange nipples used with E-z-mate Series couplers. -38

42 Pneumatic Quick ouplings Features Parker ontrolled Pressure low Guns meet OSH requirements (section 29 FR paragraph b), and directive # ompressed air shall not be used for cleaning purposes except where reduced to less than 30 psi, and then only with effective chip guarding and personal protective equipment. escription 410-S Parker ontrolled Pressure low Guns features thumb lever valve actuator and brass nozzle. Inlet port is 1/4" NPT. ccessories low Guns (ontrolled Pressure) Parker ontrolled Pressure low Guns have a black epoxy coated zinc body and vented nozzles to prevent pressure build-up when dead ending occurs up to 150 psi. Specifications Part Maximum Wt. (L) No. Pressure P/Piece 410-S 150 PSI SV 150 PSI S 150 PSI 0.48 Pneumatics 410-SV Parker Venturi Nozzle ontrolled Pressure low Gun with thumb lever valve and large venturi side ports for high volume flow. Inlet port is 1/4" NPT. 415-S Parker ontrolled Pressure low Guns features push button valve actuator and brass nozzle. Inlet port is 1/4" NPT. Part No. 400-S-TIP low Gun Replacement Tip ccessories low Guns (Full Pressure) The following Parker low Guns must have a pressure regulator setting below 30 psi to conform to OSH safety requirements 29 FR Paragraph b. escription 410 Parker two way thumb lever valve has an zinc body with 1/4" NPT inlet and 1/8" NPSF outlet. Note: Standard Gun without nozzle. 410-N Parker thumb lever style low Gun features a zinc body, brass nozzle, and 1/4" NPT female inlet. Specifications Part Maximum Wt. (L) No. Pressure P/Piece PSI N 150 PSI N 150 PSI N Parker low Gun features a push button style actuator, zinc body with a brass nozzle and 1/4" NPT female inlet. -39

43 Pneumatic Quick ouplings ccessories G Series Part Meets OSH Number Nozzle Requirements G441-NL Extended No Part Meets OSH Number Nozzle Requirements G442-SL Extended Yes Part Meets OSH Number Nozzle Requirements G443-NL 1/8 Female NPT No escription Made from impact resistant plastic, G Series blow guns are durable and versatile. Extended nozzles allow air to be directed where it is required. The pistol grip trigger allows greater control over the amount of air delivered. ombined, these two features provide superior performance in a light weight, ergonomically designed package. Nozzles are available in short and extended versions and most models meet OSH directives on the use of compressed air for cleaning purposes. OSH directive #100-1 states that "when dead ending occurs a static pressure at the main orifice shall not exceed 30 psi." For those blow guns that do not meet this requirement, OSH requires that "compressed air shall not be used for cleaning purposes except where reduced to less than 30 psi, and then only with effective chip guarding and personal protective equipment" (section 29 FR paragraph b). Please refer to the blow gun descriptions below for compatibility with OSH directive # Nozzle configurations are designed for maximum flexibility. pplications with special requirements may find the G443- NL with a 1/8" NPT fitting convenient for adapting existing nozzles or extra-long extensions. For information on specials or made-to-order blow gun nozzles, please contact the Quick oupling ivision. Features Easy to control variable flow pistol grip trigger. Nozzles available that meet OSH requirements. Lightweight ergonomical design. odies are constructed of impact resistant plastic. Specifications Part Meets OSH Number Nozzle Requirements G444-SL Vortec Yes Rated Pressure (PSI) Temperature Range Inlet Port How to Order 175 psi to 120 F 1/4 NPTF G Part Number: G SL olor L - lack Meets OSH Requirement S - Yes N- No Nozzle Style 41 - Extended 42 - Extended (Meets OSH Requirement) 43-1/8" FNPT 44 - Short (Meets OSH Requirement) Inlet Port in 16ths G Series low Gun -40

44 Pneumatic Quick ouplings Features Parker two-way valves are designed for use in air or liquid service. ccessories Two-Way Valves escription Pneumatics odies are constructed of black molded polypropylene. The valve cartridge components are machined from brass and stainless steel for corrosion resistance and long life. Nitrile stem seals are standard. dd suffix Y for optional fluorocarbon seal. onsult factory for price and delivery. P410 Two way valve with forward positioned lever handle. Inlet and outlet ports are 1/4" NPT. Specifications Rated Pressure (PSI) 70 F 180 F Temperature Range -20 to 180 F P415 Two way valve features push button style valve actuator. Inlet and outlet ports are 1/4" NPT. P420 Reverse oriented lever handle is used in carpet cleaning applications which utilize tube mounted valves. Inlet and outlet ports are 1/4". -41

45 Hydraulic Hydraulics Quick ouplings -1

46 Hydraulic Quick ouplings Introduction Hydraulics ouble Shut-Off and Straight-Thru ouplings Parker hydraulic couplings have a wide variety of designs, each tailored to a particular application or use. This catalog is arranged according to those categories. In each section the construction of a specific design will be detailed. However, based on the valving of the coupling, hydraulic couplings generally fall into one of two groups, either ouble Shut-Off or Straight-Thru. ouble Shut-Off couplings are used extensively when it is important to minimize fluid loss upon disconnection. oth halves of the coupler, the body and the nipple, contain shutoff valves. These valves open automatically when the body and nipple are connected, and close automatically when the two halves are disconnected keeping fluid loss to a minimum. Parker Straight-Thru couplings have no valves in either half and are ideal for maximum flow application. Their smooth, open bore offers the lowest pressure drop of any quick disconnect coupling, and allows them to be thoroughly cleaned. Since there are no valves in either half, fluid flow should be shut off before the coupling is disconnected. Rated Pressure Rated pressure for the Parker hydraulic couplings range from 30 to 15,000 psi, depending on the coupling series, size and materials. Rated pressures as shown in this catalog are defined by ISO 5598, as the qualified operating pressures which are recommended for a component or a system by the manufacturer. Parker Rated Pressures have been established on the basis of laboratory tests which include, but are not limited to, static burst tests and multiple cycle impulse tests. System characteristics such as high cycling rates and high amplitude shocks either hydraulic or mechanical, can reduce the functioning life of a coupling, even if the system s nominal pressure falls within the rated pressure range of the coupling. For assistance in analyzing your application, contact your nearest Parker sales office or the in Minneapolis. Refer to the Safety Guide at the end of this catalog for considerations when selecting a Quick oupling. Refer to the Fluid ompatibility hart (note Table of ontents) for seal selection assistance for both ouble Shut-Off and Straight-Thru couplings. hecklist for Selecting Quick ouplings q What are the functional requirements of the coupling? q What is the maximum working pressure of the application? q Which seals and body material are compatible with the system s fluid? q Is the application static or dynamic? q What size coupler is required? q What is the maximum pressure drop suitable for the application? q oes the application require the ability to connect and disconnect under pressure? q What is the media temperature and ambient temperature? q What end configurations are required? q Is an industry interchange coupler required? q Is air inclusion and fluid loss a concern in the application? -2

47 Hydraulic Quick ouplings Table of ontents Introduction...-2 oupling Selection Guide...-4 General Purpose ouplings 60 Series ouplers Nipples Repair Kits & Replacement Parts Series Steam...-9 ouplers...-9 Nipples Series ouplers Nipples SM Series ouplers Nipples HP Series ouplers Nipples Series ouplers Nipples Series ouplers Nipples Non-Spill ouplings NS Series ouplers Nipples dapters FF Series ouplers Nipples FEM Series ouplers Nipples F Series Nipples FE Series Nipples FH Series ouplers Nipples FS Series ouplers Nipples Repair Kits onnect Under Pressure ouplings 6100 Series ouplers Nipples Series ouplers Nipples Series ouplers Nipples Series ouplers Nipples High Pressure ouplings 3000 Series ouplers Nipples T Series ouplers Nipples Series Mold oolant Line ouplings Moldmate Series ouplers Sub ssemblies & Replacement Parts Nipples High Flow ouplings ST Series ouplers Nipples Water Service HO Series Special Purpose - Miniature M Series ust Plugs and ust aps Ordering Information Promotional Products-Keychains Hydraulics -3

48 Hydraulic Quick ouplings oupling Selection & Ordering Guide Hydraulics Valving ody Material* Locking Std. Seal Temp Rated Size r S S3 S6 Mechanism Material** Range** Pressure General Purpose 60 Series Poppet 1/8-2 1/2" l l l l all Nitrile -40 to +250 F 1000 to 5000 PSI 60 Series Steam Poppet 1/4 to 1" l all Ethylene Propylene -65 to +400 F 6600 Series Poppet 1/4 to 1" l all Nitrile -40 to +250 F 4000 to 5000 PSI SM Series Poppet 1/4 to 3/4" l all Nitrile -40 to +250 F 4500 to 6000 PSI HP Series Poppet 1 to 1 1/2" l all Nitrile -40 to +250 F 5000 PSI 4000 Series Poppet/all 1/4 to 1" l all Nitrile -40 to +250 F 3000 PSI 4200 Series Poppet/all 3/8 to 1/2" l all Nitrile -40 to +250 F 3000 PSI Non-Spill NS Series Flush Face 3/8 to 1" l all Nitrile -40 to +250 F 2500 PSI dapter Flush Face/Poppet 1/2" l all Nitrile/Polyurathane -40 to +250 F 3000 to 3625 PSI FF Series Flush Face 1/4 to 1" l all Nitrile/Polyurathane -40 to +250 F 3000 to 5000 PSI FEM Series Flush Face 1/4 to 1" l all Nitrile/Polyurathane -40 to +250 F 3000 to 5000 PSI FS Series Flush Face 1/4 to 1" l all Fluorocarbon -15 to +400 F 2000 PSI Non-Spill onnect Under Pressure F Series Flush Face 3/8 to 3/4" l all Nitrile/Polyurathane -40 to +250 F 3000 PSI FE Series Flush Face 1/2 to 3/4" l all Nitrile/Polyurathane -40 to +250 F 3000 PSI 6100 Series Flush Face 3/4 to 1 1 /2" l Threads Nitrile -40 to +250 F 2000 to 3000 PSI onnect Under Pressure 8200 Series Poppet 1/2" l all Nitrile -40 to +250 F 3000 PSI 9200 Series Poppet 1/2" l all Nitrile -40 to +250 F 3000 PSI 5000 Series all 1/2" l Threads Nitrile -40 to +250 F 2500 PSI High Pressure FH Series Flush Face 3/8" l all Nitrile -40 to +250 F 10,000 PSI 3000 Series all 1/4 to 3/8" l Threads Polyurethane -22 to +230 F 10,000 PSI T Series Poppet 3/8" l all Fluorocarbon -15 to +400 F 10,000 PSI 1141 Series Poppet 1/4" l Threads Polyurethane -40 to +180 F 10,000 PSI Mold oolant Moldmate Valved & Unvalved 1/4 to 1/2" l all Silicone -20 to +400 F 200 PSI High Flow ST Series Unvalved 1/8 to 1 1/2" l l l all Nitrile -40 to +250 F 2500 to 6700 PSI HO Series Unvalved 1/4 to 1/2" l all Nitrile -40 to +250 F 10,000 to 15,000 PSI Water Service Unvalved 3/4" l all Nitrile -40 to +250 F 200 PSI Special Purpose - Miniature M Series Poppet 1/8 l all Fluorocarbon -15 to +400 F 250 PSI See Fluid ompatibility chart and/or consult factory for questions regarding proper material for specific applications. * Material ode: r = rass; S = Steel; S3 = 303 Stainless Steel; S6 = 316 Stainless Steel **Optional Seals Seal Material Specific oupling Series Using Optional Seal Suffix esignator at left W Ethylene Propylene 60, 6600, 4000, 4200, 6100, 5000, 8200, 9200, ST Y Fluorocarbon 60, 6600, 4000, 4200, 6100, 5000, 8200, 9200, ST, Moldmate (if used wih oil based media only) Z Neoprene 60, 6600, 4000, 4200, 6100, 5000, 8200, 9200, ST E5 Ethylene Propylene SM, HP, NS, FF, FEM, FH, FS, HO E4 Fluorocarbon SM, HP, NS, FF, FEM, FH, FS (ST-no suffix needed), HO, T (Fluorocarbon only-no suffix needed) E12 Neoprene SM, HP, NS, FF, FEM, FH, FS,HO E47 Perfluoroelastomer SM, HP, NS, FF, FEM, FH, FS (ontact the division re: Perfluoroelastomer options) 3000 and 1141 with Polyurethane only (no suffix needed) Water Service (Nitrile only) To select proper Seal Materials, see Fluid ompatibility chart in ppendices, or contact your Parker Quick oupling istributor. -4

49 Hydraulic Quick ouplings General Purpose ouplings 60 Series pplications Parker general purpose couplings, are used across the spectrum of hydraulic applications. These ouble Shut-Off couplings can be found anywhere that fluid transfer lines need to be connected and disconnected for operation or maintenance of equipment, and a loss of fluid is undesirable. Primarily used with hydraulic fluid, general purpose ouble Shut-Off couplings are also used with chemicals, water, steam, and some gases. Special Order Information 60 Series couplings are available in hromium-6 Free plated steel, brass, 303 stainless steel, and 316 stainless steel. rass couplings have double O-Ring seals and stainless locking balls. Standard seal material is Nitrile; optional seal materials are available. For 316 stainless steel products, standard seal material is Fluorocarbon, and other seal materials are available upon request. See Fluid ompatibility hart at end of this catalog. ll sizes of 60 Series can be furnished with locking sleeves. Place suffix letters -SL (Sleeve-Lok) after regular catalog numbers. Example H3-62-SL. Parker 60 Series heavy duty nipples are recommended where high cycle rates and pressure surges are encountered. Machined from high tensile steel and induction hardened, they are hromium-6 Free plated. To specify a heavy duty nipple, add the prefix H to the steel part number; thus: H-H2-63. Note Protective dust plugs and caps play a crucial role in the life of a quick coupling and no purchase of a hydraulic quick coupling is complete without the selection of an appropriate dust plug and cap. See pages noted in Table of ontents for dust plugs and caps for the Parker full line of hydraulic couplings. Hydraulics Specifications Industry Standard: Parker 60 Series couplings comply with ISO 7241 Series Standard. NSI/ISO Pressure Rating: ynamic applications with normal to moderate hydraulic shocks such as general industrial equipment, hydraulic presses, agricultural equipment, etc. Impulse tested at a multiple (125% to 133%) of rated pressure. Low ycle, Non-pulsating Pressure Rating: pplications with lower cycle life and no severe cyclic pressure fluctuations, essentially steady pressure during an operating cycle. Typical applications include hydraulic jacks, mine roof support systems, and high pressure fluid transfer (pumping water or slurry in oil wells). Minor pump ripple is considered non-pulsating. Impulse tested at rated pressure. ody Size (in.) 1/8 1/4 3/8 1/2 3/ /2 2 1/2 Rated Pressure (PSI) rass Stainless steel Steel Steel w / H nipple N/ N/ N/ 1/8 1/4 3/8 1/2 3/ /2 2 1/2 Rated Pressure (PSI) N/ N/ Seal Temperature Range: Nitrile: -40 F to +250 F (Standard seal for rass, Steel, & 303 Stainless Steel couplings). Fluorocarbon: -15 F to +400 F (Standard seal for 316 Stainless Steel couplings). Other Seal materials: ontact the ivision for availability. Vacuum ata: 27.4 inches Hg. both connected and disconnected (1-1/2" and 2-1/2" body size 60 Series couplings are not recommended for service in disconnected mode) Note: Read the Safety Guide for Selecting and Using Quick ction ouplings and Related ccessories before making a coupling selection. It may be found in Parker Hannifin Quick oupling ivision catalogs and is available as Parker Publication No ody Size (in.) 1/8 1/4 3/8 1/2 3/ /2 2 1/2 Rated Flow (GPM)

50 Hydraulic Quick ouplings General Purpose ouplings 60 Series Hydraulics Features Large flow areas machined into the body of the coupler and nipple facilitate flow around the valve, for a high flow capacity. 2. Positive valve stop. The perch maintains valve alignment and provides metal to metal valve stop to ensure that the valves open fully, every time. 3. aptive valve seal assures bubble tight poppet sealing. The valve seal is positively captured by the metal poppet to minimize seal washout or damage from high velocity fluid Hardened nipples and sleeves (steel) and solid barstock construction make for a quality coupling with maximum resistance to damage from hydraulic and mechanical shock. 5. The seal is designed to withstand high pressures and provide reliable sealing. wide selection of optional seal materials are available, see Fluid ompatibility hart at end of this catalog for selection assistance. Steel versions feature PTFE back-up rings that support mating seals for high pressure applications. rass couplers have a double O- ring seal for redundancy in low pressure, vacuum and steam applications. 6. urable ball-locking mechanism assures reliable connection, every time. large number of locking balls distributes the work load evenly while providing alignment and swiveling action to reduce hose torque and prolong hose life. 7. Manufactured from brass, steel and stainless steel as standard materials. wide range of seals allow these couplings to be used with a broad range of media. 8. lso available with a Straight Thread (OR) end configuration available as standard. 9. Industrial Standard: Parker 60 Series couplings comply with ISO 7241, Series Standard. Performance 60 Series (1/8" & 1/4") Test Fluid: Oil SUS Series (3/8" & 1/2") Test Fluid: Oil SUS Pressure rop in PSI /8" 1/4" Pressure rop in PSI /8" 1/2" Flow in USGPM Flow in USGPM Series (3/4" & 1") Test Fluid: Oil SUS Series (1-1/2" & 2-1/2") Test Fluid: Oil SUS Pressure rop in PSI /4" 1" Pressure rop in PSI /2" 2-1/2" Flow in USGPM Flow in USGPM -6

51 Hydraulic Quick ouplings General Purpose ouplings 60 Series ouplers Female Thread ody Part Part Part No. Part No. Thread Thread imensions (in.) Size No. Wt. (L.) No. Wt. (L.) Type 303 Wt. (L.) Type 316 Wt. (L.) Size Size Overall Wrench Largest (in.) rass P/Piece Steel P/Piece Stainless P/Piece Stainless P/Piece NPTF OR Length Flats iameter 1/8 H H SH SSH1-62Y / /8 H1-62-T SH1-62-T SSH1-62Y-T / /4 H H SH SSH2-62Y / /4 H2-62-T SH2-62-T SSH2-62Y-T / /8 H H SH SSH3-62Y / /8 H3-62-T SH3-62-T SSH3-62Y-T / /2 H H SH SSH4-62Y / /2 H4-62-T SH4-62-T SSH4-62Y-T / /4 H6-60 H SH SSH6-62Y / /4 H6-62-T SH6-62-T SSH6-62Y-T / H8-60 H SH SSH8-62Y / H8-62-T SH8-62-T SSH8-62Y-T / Hydraulics Nipples Female Thread E G F ody Part Part Part No. Part No. Thread Thread imensions (in.) Size No. Wt. (L.) No. Wt. (L.) Type 303 Wt. (L.) Type 316 Wt. (L.) Size Size Overall Exposed Wrench Largest (in.) rass P/Piece Steel P/Piece Stainless P/Piece Stainless P/Piece NPTF OR Length Length* Flats iameter E F G 1/8 H H SH SSH1-63Y / / H1-63-T SH1-63-T4 SSH1-63Y-T / /4 H H SH SSH2-63Y / / H2-63-T SH2-63-T SSH2-63Y-T / /8 H H SH SSH3-63Y / / H3-63-T SH3-63-T SSH3-63Y-T / /2 H H SH SSH4-63Y / / H4-63-T SH4-63-T SSH4-63Y-T / /4 H H SH SSH6-63Y / / H6-63-T SH6-63-T SSH6-63Y-T / H H SH SSH8-63Y / H8-63-T SH8-63-T SSH8-63Y-T / * * This dimension represents the portion that is exposed when the nipple is inserted into the mating Parker oupler. Optional Seals 60 Series Optional Seals Suffix W Ethylene Propylene (EPR) Y Fluorocarbon Z Neoprene Perfluoroelastomer (ontact factory for Seal options) -7

52 Hydraulic Quick ouplings General Purpose ouplings 60 Series ouplers Female Thread Hydraulics ody Part Part Part No. Part No. Thread Thread imensions (in.) Size No. Wt. (L.) No. Wt. (L.) Type 303 Wt. (L.) Type 316 Wt. (L.) Size Size Overall Wrench Largest (in.) rass P/Piece Steel P/Piece Stainless P/Piece Stainless P/Piece NPTF OR Length Flats iameter 1 1/2 H12-60L 4.58 H12-62L 4.70 SH12-62L 4.68 SSH12-62LY /4-11 1/ /2 H12-60N 4.58 H12-62N 4.70 SH12-62N 4.68 SSH12-62NY /2-11 1/ / H12-62-T SH12-62-T SSH12-62Y-T / / H12-62-T SH12-62-T SSH12-62Y-T / /2 H H SH SSH Y / /2 H H SH SSH Y 2 1/ /2 H H SH SSH Y Wrench Flat on 303 Stainless is 2.50 in. Nipples E Female Thread G ody Part Part Part No. Part No. Thread Thread imensions (in.) Size No. Wt. (L.) No. Wt. (L.) Type 303 Wt. (L.) Type 316 Wt. (L.) Size Size Overall Exposed Wrench Largest (in.) rass P/Piece Steel P/Piece Stainless P/Piece Stainless P/Piece NPTF OR Length Length* Flats iameter F E F G 1 1/2 H12-61L 2.96 H12-63L 3.10 SH12-63L 3.06 SSH12-63LY 1 1/4-11 1/ /2 H12-61N 2.96 H12-63N 3.10 SH12-63N 3.06 SSH12-63NY 1 1/2-11 1/ /2 H12-63-T SH12-63-T SSH12-63Y-T20 1 5/ /2 H12-63-T SH12-63-T SSH12-63Y-T24 1 7/ /2 H H SH SSH Y / /2 H H SH SSH Y 2 1/ /2 H H SH SSH Y * This dimension represents the portion that is exposed when the nipple is inserted into the mating Parker oupler. Largest diameter on rass is 2.96" across Hex orners Hex on 303 Stainless is 2.50 in. Replacement Parts 60 Series ouplers ody Size (in.) O-Rings - Nitrile ack-up Rings 1/ H / H / / / / (Valve) (Fitting) (ody 2 req.) 2-1/ (Valve) (Fitting) (ody) Repair Kits ouplers Nipples ody Repair Kit Used For Repair Kit Used For Size (in.) Part No. Part No. Part No. Part No. 3/8 H67E-62K H3-62 H67E-63K H3-63 H67E-60K H3-60 H67E-61K H3-61 SH67E-62K SH3-62 SH67E-63K SH3-63 SSH67-62KY SSH3-62Y SSH67E-63KY SSH3-63Y 1/2 H67F-62K H4-62 H67F-63K H4-63 H67F-60K H4-60 H67F-61K H4-61 SH67F-62K SH4-62 SH67F-63K SH4-63 SSH67F-62KY SSH4-62Y SSH67F-63KY SSH4-63Y 3/4 H67G-62K H6-62 H67G-63K H6-63 H67G-60K H6-60 H67G-61K H6-61 SH67G-62K SH6-62 SH67G-63K SH6-63 SSH67G-62KY SSH6-62Y SSH67G-63KY SSH6-63Y 1 H67J-62K H8-62 H67J-63K H8-63 H67J-60K H8-60 H67J-61K H8-61 SH67J-62K SH8-62 SH67J-63K SH8-63 SSH67J-62KY SSH8-62Y SSH67J-63KY SSH8-63Y -8

53 Hydraulic Quick ouplings General Purpose ouplings 60 Series Steam ouplings Specifications ody Size (in.) 1/4 to 1 Standard Seal Material Ethylene Propylene Temperature Range up to +400 Hydraulics oupler Female Pipe Thread ody Part Thread imension (in.) Size No. Size Overall Wrench Largest Wt. (L.) (in.) rass NPTF Length Flats iameter P/Piece 1/4 H2-60-STM 1/ /8* H3-68 3/ /2 H4-60-STM 1/ /4 H6-60-STM 3/ H8-60-STM / * See Photo and rawing below for 3/8 inch size coupler configuration. oupler - 3/8 Inch onfiguration Female Pipe Thread Nipple Female Pipe Thread E ody Part Thread imension (in.) Size No. Size Overall Exposed* Hex Largest Wt. (L.) (in.) rass NPTF Length Length Size iameter P/Piece E F G 1/4 H2-61-STM 1/ /8 H3-69 3/ /2 H4-61-STM 1/ /4 H6-61-STM 3/ H8-61-STM / G * This dimension represents the portion that is exposed when the nipple is inserted into the mating Parker oupler. Repair Kits Steam oupling F ody Repair Kit Used For Size Part No. Part No. 3/8 H68E-67K H3-68 3/8 H69E-67K H

54 Hydraulic Quick ouplings General Purpose ouplings 6600 Series Performance 6600 Series (1/4") Test Fluid: Oil SUS 25 Hydraulics Pressure rop in PSI /4" 5 Features Poppet valves are mated with a solid metal perch that maintains valve alignment and prevents flow checking. oth the coupler's sleeve and the nipple's body are hardened to make the 6600 Series couplings resistant to damage from brinelling and mechanical shock. The durable-ball-locking mechanism ensures a reliable connection every time Series couplings have female pipe and straight thread end configurations as standard. Parker 6600 Series couplings interchange with couplings meeting ISO , Series. pplications Versatile Parker 6600 Series couplings are used in a wide range of hydraulic applications including construction equipment, manufacturing machinery, and in-plant systems. They can be found anywhere the fluid transfer lines need to be connected and disconnected for operation or maintenance of equipment. Rugged construction makes the 6600 Series a good choice for mobile applications including dump trucks, snow plows, refuse hauling, mining, asphalt paving, truck trailer connections and many more. In-plant machinery applications include hydraulic fluid, chemicals and gas lines for paper mills, steel production, and many varieties of plant maintenance and production equipment. Note: Protective dust plugs and caps play a crucial role in the life of a quick coupling and no purchase of a hydraulic quick coupling is complete without the selection of an appropriate dust plug and cap. See pages noted in Table of ontents for dust plugs and caps for the Parker full line of hydraulic couplings. Specifications ody Size (in.) 1/4 3/8 1/2 3/4 1 Rated Pressure (PSI) Rated Flow (GPM) Temperature Range (Nitrile seals) -40 to +250 F Pressure rop in PSI Pressure rop in PSI Flow in USGPM 3/8" 6600 Series (3/8"& 1/2") Test Fluid: Oil SUS Flow in USGPM Series (3/4" & 1") Test Fluid: Oil SUS 3/4" Flow in USGPM 1/2" 1" -10

55 Hydraulic Quick ouplings General Purpose ouplings 6600 Series ouplers Female Thread ody Part Thread Thread imensions (in.) Size No. Size Size Overall Hex Largest Wt. (L.) (in.) Steel NPTF OR Length Size iameter P/Piece 1/ / / / / / / / / / / / / / / / / / / / / / / / Hydraulics Nipples Female Thread E F G ody Part Thread Thread imensions (in.) Size No. Size Size Overall Exposed* Hex Largest Wt. (L.) (in.) Steel NPTF OR Length Length Size iameter P/Piece E F G 1/ / / / / / / / / / / / / / / / / / / / / / / / * This dimension represents the portion that is exposed when the nipple is inserted into the mating parker oupler. Replacement Parts 6600 Series ody Size (in.) 1/4 3/8 1/2 3/4 1 O-Rings - Nitrile ack-up Rings

56 Hydraulic Quick ouplings General Purpose ouplings SM Series Features Hydraulics The SM Series couplings feature: Poppet valves with captive valve seals: the valve seal is positively captured by the metal poppet to minimize seal washout. oupler and nipple are precision machined from solid barstock. SM Series are available in female pipe (NPTF), SE O-Ring oss and ritish Pipe (SPP) as standard. pplications SM Series couplings are used across the spectrum of hydraulic applications. These ouble Shut-Off couplings can be found anywhere that fluid transfer lines need to be connected and disconnected for operation or maintenance of equipment, and a loss of fluid is undesirable. esigned for use with commercial grades of hydraulic fluids. These couplings are ideally suited for all mobile or industrial applications. Specifications ody Size (in.) 1/4 1/2 3/4 Rated Pressure (PSI) 6,000 6,000 4,500 Rated Flow (GPM) Temperature Range (Nitrile Seals) -40 to +250 F Note: Protective dust plugs and caps play a crucial role in the life of a quick coupling and no purchase of a hydraulic quick coupling is complete without the selection of an appropriate dust plug and cap. See pages noted in Table of ontents for dust plugs and caps for the Parker full line of hydraulic couplings. Performance SM Series (1/4") Test Fluid: Oil SUS SM Series (1/2" & 3/4") Test Fluid: Oil SUS Pressure rop in PSI /4" Pressure rop in PSI /2" 3/4" Flow in USGPM Flow in USGPM -12

57 Hydraulic Quick ouplings General Purpose ouplings SM Series ouplers Female Thread ody Part imensions (in.) Size No. Thread Overall Hex Largest Wt. (L.) (in.) Steel Size Length Size iameter P/Piece 1/4 SM-251-4FP 1/4-18 NPTF /4 SM-251-4F G1/4 SPP /4 SM-251-6FP 3/8-18 NPTF /4 SM-251-6F G3/8 SPP /4 SM-251-6FO 9/16-18OR /2 SM-501-8FP 1/2-14 NPTF /2 SM-501-8F G1/2 SPP Hydraulics 1/2 SM FP 3/4-14 NPTF /2 SM F G3/4 SPP /2 SM-501-8FO 3/4-16OR /4 SM FO 1 1/16-12OR /4 SM FP 3/4-14 NPTF /4 SM F G3/4 SPP /4 SM FP /2 NPTF /4 SM F G 1 SPP /4 SM FO 1-5/16-12OR Nipples Female Thread ody Part imensions (in.) Size No. Thread Overall Exposed* Hex Largest Wt. (L.) (in.) Steel Size Length Length Size iameter P/Piece E F G 1/4 SM-252-4FP 1/4-18 NPTF /4 SM-252-4F G1/4 SPP /4 SM-252-6FP 3/8-18 NPTF /4 SM-252-6F G3/8 SPP /4 SM-252-6FO 9/16-18OR /2 SM-502-8FO 3/4-16OR /2 SM-502-8FP 1/2-14 NPTF /2 SM-502-8F G1/2 SPP G 1/2 SM FP 3/4-14 NPTF /2 SM F G3/4 SPP E F 3/4 SM FO 1 1/16-12OR /4 SM FP 3/4-14 NPTF /4 SM F G3/4 SPP /4 SM FP /2 NPTF /4 SM F G 1 SPP /4 SM FO 1-5/16-12OR * This dimension represents the portion that is exposed when the nipple is inserted into the mating parker oupler. Optional Seals Optional Seals Suffix (Standard seals are Nitrile) E4 Fluorocarbon E5 Ethylene Propylene (EPR) E12 Neoprene Perfluoroelastomer (ontact Factory for Seal Options) -13

58 Hydraulic Quick ouplings General Purpose ouplings HP Series (High Pressure oupling) Features Hydraulics Operating pressures up to 5,000 PSI (350 ar). Soft seat valving prevents leakage when coupler and nipple are disconnected. Made of arbon Steel. Exterior is hromium-6 Free plated for corrosion resistance. Smooth Flow Path Minimizes Pressure rop. Nitrile ody Seal supported by PTFE washer. ackup washer keeps seal from extruding at high pressures. Heat Treated Nipple and Heavy uty Locking ollar withstands high pressure surges, hose twist and repeated pressure pulses. Nitrile Seals for General Purpose Hydraulic pplications. Specifications ody Size (in.) 1 1-1/2 Rated Pressure (PSI) 5,000 5,000 Rated Flow (GPM) Temperature Range (std seals) -40 to +250 F Performance HP Series (1" & 1-1/2") Test Fluid: Oil SUS Pressure rop in PSI " 1-1/2" Flow in USGPM -14

59 Hydraulic Quick ouplings General Purpose ouplings HP Series (High Pressure oupling) ouplers ody Part Thread Overall Wrench Largest Wt. (L.) Size (in.) No. Size Length Flats iameter P/Piec 1 HP FP /2 NPSF HP FO 1 15/16-12OR /2 HP FP 1 1/2-11 1/2 NPTF /2 HP FO 1 7/8-12 OR Hydraulics Nipples G ody Part Thread Overall Wrench Largest Exposed Wt. (L.) Size (in.) No. Size Length Flats iameter Length* P/Piece E F G 1 HP FP /2 NPSF HP FO 1 15/16-12OR /2 HP FP 1 1/2-11 1/2 NPTF /2 HP FO 1 7/8-12 OR * This dimension represents the portion that is exposed when the nipple is inserted into the mating Parker oupler. F E ust Plugs and aps Protective Plugs for oupler Protective aps for Nipple P/N Material Fits oupler P/N Material Fits Nipple HPP 100 luminum HP 1001 HP 100 luminum HP-1002 HPP 150 luminum HP 1501 HP 150 luminum HP

60 Hydraulic Quick ouplings General Purpose ouplings 4000 Series Hydraulics Features Parker 4000 Series couplings feature: Poppet valves available to prevent uncoupled leakage. all valves available for rugged dependability in heavyduty hydraulic applications, within rated working pressures. ritical parts are induction hardened for durability. ependable ball-locking mechanism holds the mating halves together. ouplers and nipple are precision machined from solid bar stock. For applications with residual trapped pressure use connect-under-pressure nipples designated by the - option. The mating 8010 series nipples meet ISO 5675 requirements. pplications The 4000 Series brings to the industry a proven design for use on construction equipment, forestry equipment, agricultural machinery, oil tools, steel mill machinery, and other demanding hydraulic applications. Performance Series (1/4", 3/8", 1/2") Test Fluid: Oil SUS Note: Protective dust plugs and caps play a crucial role in the life of a quick coupling and no purchase of a hydraulic quick coupling is complete without the selection of an appropriate dust plug and cap. See pages noted in Table of ontents for dust plugs and caps for the Parker full line of hydraulic couplings. Pressure rop in PSI /4" 3/8" 1/2" Special Order Information Standard seal material is Nitrile, other seal options are available. See Ordering Information at end of Section and Fluid ompatibility hart at end of this catalog for assistance in making seal selection. Note: The part numbers for the 4000 Series Poppet Valve design are designated with a -P. For example P Flow in USGPM 4000 Series (3/4" & 1") Test Fluid: Oil SUS 80 Specifications ody Size (in.) 1/4 3/8 1/2 3/4 1 Rated Pressure (PSI) Rated Flow (GPM) Temperature Range (std seals) -40 to +250 F Pressure rop in PSI /4" 1" Flow in USGPM -16

61 Hydraulic Quick ouplings General Purpose ouplings 4000 Series ouplers Female Thread ody Part Thread Thread Thread imensions (in.) Size No. Size Size Size Overall Wrench Largest Wt. (L.) (in.) Steel* NPTF OR SPP Length Flats iameter P/Piece 1/ P 1/ / P-T8M 3/4-16 (Male) / T6 9/ /4 4050P-T6** 9/ / P 3/ / / / P 1/ / / / P 3/ / / / P 3/ / / / P 7/ / SPP 1/ / / P / Hydraulics Nipples Female Thread E G F onnect-under-pressure * P in part number designates Poppet design ** Push-to-onnect design. ody Part Thread Thread Thread imensions (in.) Size No. Size Size Size Overall Exposed Hex Largest Wt. (L.) (in.) Steel* NPTF OR SPP Length Length Size iameter P/Piece E F G 1/ P 1/ / T6 9/ / P 3/ / / / P 1/ / / / P 3/ / / / P 3/ / / / P 7/ / SPP 1/ / / P / * P in part number designates Poppet design This dimension represents the portion that is exposed when the nipple is inserted into the mating Parker oupler. E ody Part Thread Thread Thread imensions (in.) Size No. Size Size Size Overall Exposed Hex Largest Wt. (L.) (in.) Steel* NPTF OR SPP Length Length Size iameter P/Piece E F G 1/ P- 1/ / P- 3/ G F Replacement Parts Series ody Size (in.) 1/4 3/8 1/2 3/4 1 O-Rings - Nitrile

62 Hydraulic Quick ouplings General Purpose ouplings 4200 Series Hydraulics Features Parker 4200 Series couplings feature: ouble acting sleeve for one handed push-to-connect operation when coupler is clamp or bulkhead mounted. Poppet valves available to prevent uncoupled leakage. all valves available for rugged dependability in heavy-duty hydraulic applications, within rated working pressures. ritical parts are induction hardened for durability. ependable ball-locking mechanism holds the mating halves together. ouplers and nipple are precision machined from solid bar stock. For applications with residual trapped pressure use connect-under-pressure nipples designated by the - option. pplications The 4200 Series brings to the industry a proven design for use on construction equipment, forestry equipment agricultural machinery, and oil tools. Note: Protective dust plugs and caps play a crucial role in the life of a quick coupling and no purchase of a hydraulic quick coupling is complete without the selection of an appropriate dust plug and cap. See pages noted in Table of ontents for dust plugs and caps for the Parker full line of hydraulic couplings. Specifications ody Size (in.) 3/8 1/2 Rated Pressure (PSI) Rated Flow (GPM) 6 12 Temperature Range (std seals) Performance 4200 Series (3/8" & 1/2") Test Fluid: Oil SUS -40 to +250 F Special Order Information 60 Standard seal material is Nitrile. For other seal options see Table of ontents. See Ordering Information at end of Section and Fluid ompatibility hart at end of this catalog for assistance in making seal selection. Note: The part numbers for the 4200 Series Poppet Valve design are designated with a -P. For example P. Pressure rop in PSI /8" 1/2" Flow in USGPM -18

63 Hydraulic Quick ouplings General Purpose ouplings 4200 Series ouplers Female Thread ody Part Thread Thread imensions (in.) Size No. Size Size Overall Wrench Largest Wt. (L.) (in.) Steel* NPTF OR Length Flats iameter P/Piece 3/ P 3/ / / / P 1/ / / / P 3/ Hydraulics * P in part number designates Poppet design Nipples Female Thread E G ody Part Thread Thread imensions (in.) Size No. Size Size Overall Exposed Hex Largest Wt. (L.) (in.) Steel* NPTF OR Length Length** Size iameter P/Piece E F G 3/ P 3/ / / / P 1/ / / / P 3/ * P in part number designates Poppet design ** This dimension represents the portion that is exposed when the nipple is inserted into the mating Parker oupler. F onnect-under-pressure E ody Part Thread Thread Thread imensions (in.) Size No. Size Size Size Overall Exposed Hex Largest Wt. (L.) (in.) Steel* NPTF OR SPP Length Length** Size iameter P/Piece E F G 1/ P- 1/ / P- 3/ G ** This dimension represents the portion that is exposed when the nipple is inserted into the mating Parker oupler. F Replacement Parts Series ody Size (in.) Part Number escription Material 1/ O-Rings Nitrile 3/ O-Rings Nitrile -19

64 Hydraulic Quick ouplings Non-Spill ouplings NS Series Hydraulics Pressure rop in PSI Pressure rop in PSI pplications Non-Spill couplings by Parker are widely used in the public utility market where hydraulic oil spillage can constitute a serious safety hazard, particularly in overhead bucket hoists that are used for maintenance of high-voltage power transmission lines. These couplings are also used for quick change of hydraulic hand tools in the construction, railway maintenance and mining industries. They are also ideal for inplant use where excess oil spillage can create a hazard. Note: See pages noted in Table of ontents for dust plugs and caps for the Parker full line of hydraulic couplings. Performance NS Series (3/8"& 1/2") Test Fluid: Oil SUS 3/8" Flow in USGPM NS Series (3/4" & 1") Test Fluid: Oil SUS 3/4" Flow in USGPM 1" 1/2" Features 1. Positive valve stop. The perch maintains valve alignment and provides metal to metal valve stop to ensure that the valves open fully, every time. 2. aptive valve seal assures bubble tight poppet sealing. The valve seal is positively captured by the metal poppet to minimize seal washout or damage from high velocity fluid. 3. Steel construction, hromium-6 Free plated. Hardened nipples and sleeves and solid barstock construction for maximum resistance to damage from hydraulic and mechanical shock. 4. The seal is designed to withstand high pressures and provide reliable sealing. 1/2" and above sizes feature PTFE back-up rings that support mating seals for high pressure applications. 5. urable ball-locking assure reliable connection, every time. large number of locking balls distribute the work load evenly while providing alignment and swiveling action to reduce hose torque and prolong hose life. UTION: these products are not to be used as swivels, rotation under pressure will result in excessive and premature wear. 6. Female pipe (NPSF), SE O-Ring oss and ritish pipe (SPF) are available as standard. 7. ry-isconnect Series couplings employ flush valving when connecting or disconnecting. This means that the valves are mated together so that only small amounts of fluid can be lost during disconnection or air included during reconnection. 8. Sleeve locking mechanism prevents accidental disconnection when the coupling is dragged along the ground. Sleeve is rotated to engage the lock. The sleevelock feature is standard on this product. Specifications ody Size (in.) 3/8 1/2 3/4 1 Rated Pressure (PSI) Rated Flow (GPM) Temperature Range (std seals) -40 to +250 F Spillage (ML) (max. per disconnect) ir Incl. (ML) (max. per disconnect) -20

65 Hydraulic Quick ouplings Non-Spill ouplings NS Series ouplers ody Part imensions (in.) Size No. Thread Overall Hex Largest Wt. (L.) (in.) Steel Size Length Size iameter P/Piece 3/8 NS-371-6FP 3/8-18 NPSF /8 NS-371-6F G3/8 SPP /8 NS-371-8FO 3/4-16UNF /2 NS-501-8FP 1/2-14 NPSF /2 NS-501-8F G1/2 SPP /2 NS FO* 7/8-14UNF /4 NS FP 3/4-14 NPSF /4 NS F G3/4 SPP /4 NS FO 1 1/16-12UN NS FP /2 NPSF NS F G 1 SPP NS FO 1 5/16-12UN * ontact factory for onnect-under-pressure option availability in the 1/2 size. Hydraulics Nipples E F G ody Part imensions (in.) Size No. Thread Overall Exposed* Hex Largest Wt. (L.) (in.) Steel Size Length Length Size iameter P/Piece E F G 3/8 NS-372-6FP 3/8-18 NPSF /8 NS-372-6F G3/8 SPP /8 NS-372-8FO 3/4-16UNF /2 NS-502-8FP 1/2-14 NPSF /2 NS-502-8F G1/2 SPP /2 NS FO 7/8-14UNF /4 NS FP 3/4-14 NPSF /4 NS F G3/4 SPP /4 NS FO 1 1/16-12UN NS FP /2 NSPF NS F G 1 SPP NS FO 1 5/16-12UN * This dimension represents the portion that is exposed when the nipple is inserted into the mating Parker oupler. Standard Port onfigurations FP - Female Pipe Thread FO - Female Straight Thread F - Female ritish Standard Pipe Parallel Optional Seals Optional Seals Suffix E4 Fluorocarbon E5 Ethylene Propylene (EPR) E35 Perfluoroelastomer (ontact factory for Seal options) -21

66 Hydraulic Quick ouplings Non-Spill dapters Hydraulics pplications Parker Non-Spill dapters were designed due to the widespread use of several coupling types in the construction market. These adapters help the user adapt between poppet style couplings and non-spill type couplings. dapters are widely available with Parker FEM and FF Series to Parker 6600 Series coupling connections. This product is especially useful where multiple hydraulic attachments are being used with skid steer loaders. Materials Of onstruction ody: Finish: Steel hromium-6 Free plating Specifications ody Size (in.) 1/2 Rated Pressure (PSI) ES/SE 3625 Temperature Range -40 to F Max Spillage Per isconnect (ml.).020 (Flush Face End) Max ir Inclusion Upon onnect (ml.).070 (Flush Face End) Rated Flow (GPM) 12 dapters ES-500 How To Order dapter Part Number E S 500 1/2" ody Size Male Half of dapter E FEM Series (ISO Standard) S 6600 Series dapter Series Female Half of dapter E FEM Series (ISO Standard) S 6600 Series ody Part Thread Overall Hex Largest Size Number Size Length Size iameter 1/2 ES-500 N /2 SE-500 N SE-500 Performance 60 FEM/FF to 6600 dapter (1/2") Test Fluid: Oil SUS 50 Pressure rop in PSI /2" Flow in USGPM -22

67 Hydraulic Quick ouplings Non-Spill ouplings FF Series Hydraulics 8 6 pplications Parker FF Series couplings are widely used in the public utility market where hydraulic oil spillage can constitute a serious safety hazard, particularly in overhead bucket hoists that are used for maintenance of high-voltage power transmission lines. These couplings are also used for quick change of hydraulic tools in construction, railway maintenance and mining industries. The ease of cleaning makes them ideal for use in these types of hostile environments. Note: See pages noted in Table of ontents for dust plugs and caps for the Parker full line of hydraulic couplings. Performance Pressure rop in PSI Pressure rop in PSI /4" FF Series (1/4", 3/8", 1/2") Test Fluid: Oil SUS 3/8" Flow in USGPM 3/4" FF Series (3/4" & 1") Test Fluid: Oil SUS Flow in USGPM 1/2" 1" Features 1. Sleeve locking mechanism is engaged by rotating sleeve after connection. It prevents accidental disconnection when, for example, the coupling is dragged along the ground during use. 2. Sleeve mechanism is designed to help prevent dirt from entering the internal mechanism and thus causing faulty operation when connecting or disconnecting. The sleeve covers the retaining ring and also incorporates a dust seal in the spring area. 3. Steel construction, with hromium-6 Free plating. Hardened nipples and sleeves and solid barstock construction for maximum resistance to damage from hydraulic and mechanical shock. 4. The blow-out resistant seal is designed to prevent damage during severe service conditions. 5. urable ball-locking mechanism assures reliable connections, every time. large number of locking balls distributes the work load evenly while providing alignment and swiveling action to reduce hose torque and prolong hose life. UTION: These products are not to be used as swivels. Rotation under pressure will result in excessive and premature wear. 6. Female pipe (NPSF), ritish pipe (SPP) and SE O-Ring oss are available as standard. 7. FF Series couplings employ flush valving when connecting or disconnecting. This means that the valves are mated together so that only small amounts of fluid can be lost during disconnection or air inclusion during reconnection. 8. The 3/8" size conforms to HTM (Hydraulic Tool Manufactures ssociation) standards. ll sizes incorporate flush face mating surfaces which greatly facilitate cleaning of the product when disconnected. HTM couplings (3/8" only)-coupler and nipple are marked with a directional flow arrow as per specifications. However, couplings are bi-directional. Specifications ody Size (in.) 1/4 3/8 1/2 3/4 1 Rated Pressure (PSI) Rated Flow (GPM) Temperature Range -40 to F Spillage (ML) (max. per disconnect) ir Inclusion (ML) (max. per connect) -23

68 Hydraulic Quick ouplings Non-Spill ouplings FF Series Hydraulics ouplers ody Part imensions (in.) Size No. Thread Overall Hex Largest Wt. (L.) (in.) Steel Size Length Size iameter P/Piece 1/4 FF-251-4FP 1/4-18 NPSF /4 FF-251-4MP 1/4-18 NPTF /4 FF-251-6FO 9/16-18 UNF /8 FF-371-6FP 3/8-18 NPSF /8 FF-371-8FP 1/2-14 NPSF /8 FF-371-6F G3/8 SPP /8 FF-371-8F G1/2 SPP /8 FF-371-8FO 3/4-16 UNF /2 FF-501-8FP 1/2-14 NPSF /2 FF FO 7/8-14 UNF /4 FF FP 3/4-14 NPSF /4 FF FO 1 1/16-12 UNF FF FP /2NPSF FF FO 1 5/16-12UNF Nipples E F G ody Part imensions (in.) Size No. Thread Overall Exposed* Hex Largest Wt. (L.) (in.) Steel Size Length Length Size iameter P/Piece E F G 1/4 FF-252-4FP 1/4-18 NPSF /4 FF-252-4MP 1/4-18 NPTF /4 FF-252-6FO 9/16-18 UNF /8 FF-372-6FP 3/8-18 NPSF /8 FF-372-8FP 1/2-14 NPSF /8 FF-372-6F G3/8 SPP /8 FF-372-8F G1/2 SPP /8 FF-372-8FO 3/4-16 UNF /2 FF-502-8FP 1/2-14 NPSF /2 FF FO 7/8-14 UNF /4 FF FP 3/4-14 NPSF /4 FF FO 1 1/16-12 UNF FF FP /2NPSF FF FO 1 5/16-12UNF * This dimension represents the portion that is exposed when the nipple is inserted into the mating Parker oupler. Standard Port onfigurations FP - Female Pipe Thread MP - Male Pipe Thread FO - Female Straight Thread F - Female ritish Standard Pipe Parallel Optional Seals FF Series Repair Kits Optional Seals Suffix* E4 Fluorocarbon E5 Ethylene Propylene (EPR) E35 Perfluoroelastomer (ontact Factory for Seal Options). * Optional seals include O-ring & ack-up Ring, not nti-low Out bonded seal. 1/4" Nipple 3/8" Nipple 1/2" Nipple 3/4" Nipple 1" Nipple 1/4" oupler 3/8" oupler 1/2" oupler 3/4" oupler 1" oupler FF-252-KIT FF-372-KIT FF-502-KIT FF-752-KIT FF-1002-KIT FF-251-KIT N/ N/ FF-751-KIT FF-1001-KIT FF-252-KIT-E4 FF-372-KIT-E4 FF-502-KIT-E4 FF-752-KIT-E4 FF-1002-KIT-E4 FF-251-KIT-E4 N/ N/ FF-751-KIT-E4 FF-1001-KIT-E4 FF-252-KIT-E5 FF-372-KIT-E5 FF-502-KIT-E5 FF-752-KIT-E5 FF-1002-KIT-E5 FF-251-KIT-E5 N/ N/ FF-751-KIT-E5 FF-1001-KIT-E5 FF/FS-251-TOOL N/ N/ FF/FS-751-TOOL FF/FS-1001-TOOL -24

69 FEM Series Non-Spill ouplings FEM Series FEM Series couplings are designed to meet the stringent design and pressure requirements of ISO The FEM modular design also facilitates wider variations in fitting options. Parker FEM couplers are designed for use in the construction, utility and agricultural equipment markets. s with all Parker flush-face designs the non-spill feature eliminates hydraulic spillage and air inclusion when connecting or disconnecting hydraulic attachments. The FEM Series is also ideal for many other applications where hydraulic spillage is a concern and global interchangeability with other manufacturers is important. Hydraulics Materials of onstruction ody: Steel Finish: hromium-6 Free plating Valve: Flush face valving Seal: Polyurethane or Nitrite; size dependant Features Meets or exceeds ISO specification design and test requirements. Wider size variations and increased pressures. ISO Interface for universal interchangeability. Modular design for increased flexibility with fitting port options. rinell relief on male half to increase life and resist wear. Induction hardened locking surface to resist brinelling, damage and abuse. Heat Treated components to resist scratches and wear. Smooth flow path for low pressure drop. Heavy locking collar to resist damage and abuse. low-out resistant seal on male half seal prevents damage and premature failure with residual system pressure. Push-to-connect locking mechanism. Sleeve lock is a non-standard item. Pressure rop in PSI Performance /4" FEM Series (1/4", 3/8", 1/2") Test Fluid: Oil SUS 3/8" Flow in USGPM 1/2" 50 FEM Series (5/8", 3/4", 1") Test Fluid: Oil SUS Specifications ody Size (in.) 1/4 3/8 1/2 5/8 3/4 1 Rated Pressure (PSI) Rated Flow (GPM) Temperature Range (std.seals) -40 to +250 F Spillage (ML) (max. per disconnect) ir Inclusion (ML) (max. per connect) Pressure rop in PSI 35 1" /4" 20 5/8" Flow in USGPM Lewis Road Minneapolis, MN

70 FEM Series Non-Spill ouplings FEM Series ouplers ody Size Part Thread Overall Hex Largest Wt. (L) (in.) Number Size Length Size iameter P/Piece 1/4 FEM-251-4FP-NL NPSF /4 FEM-251-6FO-NL UNF Hydraulics 3/8 FEM-371-6FP-NL NPSF /8 FEM-371-8FO-NL UNF /2 FEM-501-8FP-NL NPSF /2 FEM-501-8FO-NL UNF /2 FEM MS-NL UNS /2 FEM MF-NL UNF /2 FEM FO-NL UNF /2 FEM FO-NL UN /8 FEM FO-NL UNF /4 FEM FP-NL NPSF /4 FEM FO-NL UNF FEM FP-NL NPSF FEM FO-NL UNF Nipples ody Size Part Thread Overall Exposed Hex Largest Wt. (L) (in.) Number Size Length Length* Size iameter P/Piece E F G 1/4 FEM-252-4FP NPSF /8 FEM-372-6FP NPSF /8 FEM-372-8FO UNF /2 FEM-502-8FP NPSF /2 FEM FO UNF /2 FEM MS UNS E F G 1/2 FEM MF UNF /2 FEM FO UN /8 FEM FO UN /4 FEM FP NPSF /4 FEM FO UN FEM FP NPSF FEM FO UN * This dimension represents the portion that is exposed when the nipple is inserted into the mating Parker oupler. Standard Port onfigurations FP - Female Pipe Thread FO - Female Straight Thread MF- ulkhead Male Flare 37 JI MS - ulkhead Male Seal-lok Other Fitting Port onfigurations available upon request Lewis Road Minneapolis, MN

71 Hydraulic Quick ouplings Non-Spill ouplings F Series (onnect-under-pressure) Pressure rop in PSI escription F Series products operate slightly different from traditional non-spill couplings. With no pressure in the coupler and up to 3000 PSI of trapped pressure in the nipple, begin to couple the mating halves. elay momentarily during connection to allow trapped pressure to equalize with the mating half before completing the connection. Performance /8" F Series (3/8", 1/2", 3/4") Test Fluid: Oil SUS 1/2" 3/4" pplications Parker F Series nipple provides connect-under-pressure capability with up to 3000 PSI of trapped pressure in the nipple and are ideal for applications where residual pressure makes reconnect difficult. Utilized primarily in the construction equipment market, F Series products are commonly found on hydraulic attachments used in skid steer applications. The F Series mates with the FF Series Parker interface. Features onnect-under-pressure nipple only. Hardened locking surface. Steel construction, hromium-6 Free plating for corrosion resistance. low-out resistant seal in male nipple. Flush Face Valving Note: Protective dust plugs and caps play a crucial role in the life of a quick coupling and no purchase of a hydraulic quick coupling is complete without the selection of an appropriate dust plug and cap. See pages noted in Table of ontents for dust plugs and caps for the Parker full line of hydraulic couplings. Specifications ody Size (in.) 3/8 1/2 3/4 Rated Pressure (PSI) Rated onnect-under-pressure apability Rated Flow (GPM) Spillage (ML) (max. per disconnect) ir Inclusion (ML) (max. per connect) Hydraulics Flow in USGPM Nipples ody Part imensions (in.) Size No. Mating Thread Overall Exposed Hex Largest Wt. (L.) (in.) Steel Half Size Length Length Size iameter P/Piece E F G 3/8 F-372-6FP FF-371 3/8-18 NPSF E F G 3/8 F-372-8FO FF-371 3/4-16 UNF /8 F-372-8FP FF-371 1/2-14 NPSF /2 F-502-8FP FF-501 1/2-14 NPSF /2 F FO FF-501 7/8-14 UNF /4 F FO FF /16-12 UNF /4 F FP FF-751 3/4-14 NPSF Standard Port onfigurations FP - Female Pipe Thread FO - Female Straight Thread -27

72 Hydraulic Quick ouplings Non-Spill ouplings FE Series (onnect-under-pressure) pplications Hydraulics escription FE Series products operate slightly different from traditional non-spill couplings. With no pressure in the coupler and up to 3000 PSI of trapped pressure in the nipple, begin to couple the mating halves. elay momentarily during connection to allow trapped pressure to equalize with the mating half before completing the connection. Performance Pressure rop in PSI FE Series (1/2", 5/8", 3/4") Test Fluid: Oil SUS 1/2" 5/8" 3/4" Parker FE Series nipple provide connect-under-pressure capability with up to 3000 PSI of trapped pressure in the nipple and are ideal for applications where residual pressure makes reconnect difficult. Utilized primarily in the construction equipment market, FE Series products are commonly found on hydraulic attachments used in skid steer applications. The FE Series mates with the FEM Series interface ISO couplers. Features onnect-under-pressure nipple. Hardened locking surface. Steel construction, hromium-6 Free plating for corrosion resistance. nti blowout Nitrile/PTFE bonded nipple seal. Flush face valving. Note: Protective dust plugs and caps play a crucial role in the life of a quick coupling and no purchase of a hydraulic quick coupling is complete without the selection of an appropriate dust plug and cap. See pages noted in Table of ontents for dust plugs and caps for the Parker full line of hydraulic couplings. Specifications ody Size (in.) 1/2 5/8 3/4 Rated Pressure (PSI) Rated onnect-under-pressure apability Rated Flow (GPM) Spillage (ML) (max. per disconnect) ir Inclusion (ML) (max. per connect) Flow in USGPM Nipples ody Part imensions (in.) Size No. Mating Thread Overall Exposed Hex Largest Wt. (L.) (in.) Steel Half Size Length Length Size iameter P/Piece E F G 1/2 FE-502-8FP FEM-501 1/2-14 NPSF E G 1/2 FE FO FEM-501 7/8-14 UNF /2 FE FO FEM /16-12 UNF /8 FE FO FEM /16-12 UN /4 FE FO FEM /16-12 UN F Standard Port onfigurations FP - Female Pipe Thread FO - Female Straight Thread -28

73 Hydraulic Quick ouplings Non-Spill ouplings FH Series Features 10,000 PSI operating pressure (700 bar). Flush face, non-spill valving, both halves. Sleeve on coupler and nipple body have a RE finish for identification purposes. Simple Push-To-onnect operation. Sleeve-Lock to prevent accidental disconnect. Non interchangeable with low pressure flush face couplings. Meets performance and dimensional specifications of HTM requirements, 10,000 PSI (700 bar). nti low-out Nitrile/PTFE bonded nipple seal. Hydraulics Pressure rop in PSI escription Parker FH Series high pressure couplings are an innovative product combining the advantages of a flush-face design with a highly technical performance of a rated pressure of 10,000 PSI. For safety purposes, this product does not interchange with flush-face couplings having a lower pressure rating. Performance FH Series (3/8") Test Fluid: Oil SUS 3/8" Flow in USGPM pplications Hydraulic rimpers, utters, Jacks, enders, lamps, Wedges Rescue Equipment High Pressure Test Equipment Note: Protective dust plugs and caps play a crucial role in the life of a quick coupling and no purchase of a hydraulic quick coupling is complete without the selection of an appropriate dust plug and cap. See pages noted in Table of ontents for dust plugs and caps for the Parker full line of hydraulic couplings. Materials of onstruction ody: Steel Finish: hromium-6 Free plating Valve: Flush Face Valves Seal: nti blow-out Nitrile/PTFE bonded seal ( nipple only) Specifications ody Size (in.) 3/8 Rated Pressure (PSI) 10,000 Rated Flow (GPM) 6 Temperature Range -40 to +250 F Spillage (ML).020 (max. per disconnect) ir Inclusion (ML).070 (max. per connect) -29

74 Hydraulic Quick ouplings Non-Spill ouplings FH Series ouplers Hydraulics ody Part imensions (in.) Size No. Thread Overall Wrench Largest Wt. (L.) (in.) Steel Size Length Flats iameter P/Piece 3/8 FH-371-6FP 3/8-18 NPTF /8 FH-371-6MP 3/8-18 NPTF /8 FH-371-6F G3/8 -SPP Nipples ody Part imensions (in.) Size No. Thread Overall Wrench Largest Wt. (L.) (in.) Steel Size Length Flats iameter P/Piece E F 3/8 FH-372-6FP 3/8-18 NPTF /8 FH-372-6F G3/8 -SPP F E Standard Port onfigurations FP - Female Pipe Thread MP -Male Pipe Thread F - Female ritish Standard Parallel -30

75 Hydraulic Quick ouplings Non-Spill ouplings FS Series pplications Features Simple to operate: Push to connect, pull on knurled sleeve to disconnect. Flush face valves exhibit minimal spillage upon disconnect and minimal air inclusion upon connect. Superior locking ball design a large number of locking balls distribute the workload better and allow for some rotation between the male and female halves of the coupling under pressure. Excellent flow vs pressure drop characteristics when compared with other low spill quick couplings. Material construction is 316 stainless steel with fluorocarbon seals as standard. Wide range of seal materials available. Repair kits available to replace critical elastomer seals (all sizes). Hydraulics Parker FS Series couplings virtually eliminate fluid loss upon disconnection, and minimize air inclusion during connections. They are ideal for use where spillage may cause undesirable conditions or constitute a safety hazard. The FS Series couplings have double shut-off flush mating valves that are suitable for sealing off media in chemical processing, chemical dispensing, food processing, and other corrosive applications. Working pressures to 2000 PSI. Note: Protective dust plugs and caps play a crucial role in the life of a quick coupling and no purchase of a hydraulic quick coupling is complete without the selection of an appropriate dust plug and cap. See pages noted in Table of ontents for dust plugs and caps for the Parker full line of hydraulic couplings. Materials of onstruction Machined Parts: Stainless Steel, ISI type 316 Springs: Stainless Steel, ISI type 316. Locking alls: 1/4" SS; 3/8" - 1" - Tungsten arbide ackup Washers: PTFE Elastomer Seals: Fluorocarbon is standard. Wide range is available. Performance Flow ata 30 FS Series (1/4", 3/8", 1/2") Test Fluid: Water Specifications ody Size (in.) 1/4 3/8 1/2 3/4 1 Rated Pressure (PSI) Rated Flow (GPM) Spillage (ML) (max. per disconnect) ir Inclusion (ML) (max. per connect) V Pressure rop in PSI 25 1/2" 20 3/8" 15 1/4" Flow in USGPM Temperature Range (continuous) Part No. Seal Temp F Seal Suffix ompound Rating None* Fluorocarbon -15 to 400 E5 Ethylene Propylene (EPR) -65 to 300 E1 Nitrile -40 to 250 E35 Perfluoroelastomer (ontact Factory) -20 to 600 *Fluorocarbon is standard seal. Pressure rop in PSI /4" FS Series (3/4" & 1") Test Fluid: Water 1" Flow in USGPM -31

76 Hydraulic Quick ouplings Non-Spill ouplings FS Series Hydraulics ouplers Female Pipe Thread ody Part Thread Overall Hex Largest Wt. (L.) Size (in.) No. Size Length Size iameter P/Piece 1/4 FS-251-4FP 1/4-18 NPT /4 FS-251-4MP 1/4-18 NPTF /4 FS-251-6FO 9/16-18UNF /8 FS-371-6FP 3/8-18 NPT /8 FS-371-8FO 3/4-16 UNF /2 FS-501-8FP 1/2-14 NPT /2 FS FO 7/8-14 UNF /4 FS FP 3/4-14 NPT /4 FS FO 1-1/16-12 UNF FS FP /2 NPT FS FO 1-5/16-12 UNF Nipples Female Pipe Thread E F G ody Part Thread Overall Exposed Hex Largest Wt. (L.) Size (in.) No. Size Length Length Size iameter P/Piece E F G 1/4 FS-252-4FP 1/4-18 NPT /4 FS-252-4MP 1/4-18 NPT /4 FS-252-6FO 9/16-18 UNF /8 FS-372-6FP 3/8-18 NPT /8 FS-372-8FO 3/4-16 UNF /2 FS-502-8FP 1/2-14 NPT /2 FS FO 7/8-14 UNF /4 FS FP 3/4-14 NPT /4 FS FO 1-1/16-12 UNF FS FP /2 NPT FS FO 1-5/16 12 UNF Standard Port onfigurations FP - Female Pipe Thread MP - Male Pipe Thread FO - Female Straight Thread FS Series Repair Kits Repair kits are available for both coupler and nipple half of FS coupling. Kits include replacement elastomer seals, valve assembly and instructions to perform rebuild. Spline tool must be ordered separately to accomplish coupler half repair. Other tools required: Vise, llen Wrench and Open End Wrench. FS Repair Kits TOOL Nipple Repair Kits Spline tool for oupler Repair Replacement Seals No Suffix Fluorocarbon Seals E5 Ethylene Propylene (EPR) E35 Perfluoroelastomer (ontact the Factory) 1/4" Nipple 3/8" Nipple 1/2" Nipple 3/4" Nipple 1" Nipple FS-252-KIT FS-372-KIT FS-502-KIT FS-752-KIT FS-1002-KIT FS-252-KIT-E5 FS-372-KIT-E5 FS-502-KIT-E5 FS-752-KIT-E5 FS-1002-KIT-E5 oupler Repair Kits 1/4" oupler 3/8" oupler 1/2" oupler 3/4" oupler 1" oupler N/ FS-371-KIT FS-501-KIT FS-751-KIT FS-1001-KIT N/ FS-371-KIT-E5 FS-501-KIT-E5 FS-751-KIT-E5 FS-1001-KIT-E5 N/ FF/FS-371-TOOL FS-501-TOOL FF/FS-751-TOOL FF/FS-1001-TOOL -32

77 Hydraulic Quick ouplings onnect Under Pressure ouplings 6100 Series pplications Parker s 6100 Series, is a thread-to-connect low spill coupling that can be used in a wide range of industrial applications where connected under pressure is required. The 6100 is ideal for connecting hydraulic lines on oil field equipment like power tongs, swivels and mobile drilling rigs. It is also widely used on dump trailers to connect the tractor to wet-line hydraulic systems. The 6100 Series is suitable for many applications where high flow connect under pressure couplings are required. Other uses include: submersible pumps, engine test stands, and bulk liquid O2 transfer (Special part numbers apply contact the ivision). Hydraulics Note: Protective dust plugs and caps play a crucial role in the life of a quick coupling and no purchase of a hydraulic quick coupling is complete without the selection of an appropriate dust plug and cap. See pages noted in Table of ontents for dust plugs and caps for the Parker full line of hydraulic couplings. Specifications ody Size (in.) 3/4 3/ /4 1-1/2 ash Number *Rated Pressure (PSI) Female Half Male Half omplete oupling ssembly Rated Flow (GPM) Temperature Range (std seals) -40 to +250 F. * Minimum burst pressure is equal to three times the rated pressure. Not recommended for continuous hydraulic impulse applications at rated pressures. Performance Pressure rop in PSI /2" 6100 Series (1/2" & 3/4") Test Fluid: OIL 150 SUS 3/4" Flow in USGPM Series (1", 1-1/4", 1-1/2") Test Fluid: OIL 150 SUS 60 Pressure rop in PSI " 1-1/4" 1-1/2" Flow in USGPM -33

78 Hydraulic Quick ouplings onnect Under Pressure ouplings 6100 Series Hydraulics Features 1. The connection indicator, a Parker innovation, serves as a visual check for complete connection of the 6100 coupling. It helps prevent premature failures and leaks. It assures that the connection is complete and the valves fully open, eliminating unnecessary flow restriction. (see drawing on next page) 2. The Parker heavy-duty wing nut is ruggedly builtspecifically to withstand the hammer blows commonly used to tighten and loosen this coupler. 3. The flange is designed to give a positive no-slip bulkhead mounting to reduce downtime The bonded valve seal permits full pressure connect and disconnect without seal washout. 5. The flush face valve keeps air inclusion and spillage to a minimum. 6. orrosion resistant brass body makes this coupling compatible with a broad range of media and provides versatility Series oupling with Wingnut ody Thread Part No. Part No. Overall Wt. (L.) Size Size With Without onnected P/Piece (in.) NPTF Flange Flange Length 3/4 1/ /4 3/ / /4 1 1/4-11 1/ /2 1 1/2-11 1/ Series oupling with Hex Nut ody Thread Part No. Part No. Overall Wt. (L.) Size Size With Without onnected P/Piece (in.) NPTF Flange Flange Length 3/4 1/ /4 3/ / /4 1 1/4-11 1/ /2 1 1/2-11 1/

79 Hydraulic Quick ouplings onnect Under Pressure ouplings 6100 Series ouplers Wing Nut ody Part Thread imensions (in.) Size No. Size Overall Wrench Wing Wt. (L.) (in.) rass NPTF Length Flats Nut P/Piece 3/ / / / / / /4-11 1/ / /2-11 1/ Hydraulics Hex Nut ody Part Thread imensions (in.) Size No. Size Overall Wrench Hex Wt. (L.) (in.) rass NPTF Length Flats Size P/Piece 3/ / / / / / /4-11 1/ / /2-11 1/ Nipples F G onnection Indicator Line Part No. ody Without With Thread imensions (in.) Size Flange Flange Size Overall Hex Wrench Wt. (L.) (in.) rass rass NPTF Length Size Flats P/Piece G F 3/ / / / / / /4-11 1/ / /2-11 1/ Flanges G ody imensions (in.) Size Part No. olt Hole olt ircle (in.) Steel iameter iameter G H 3/ (1 piece) (1 piece) / (2 piece) / (2 piece) H -35

80 Hydraulic Quick ouplings onnect Under Pressure ouplings 8200 Series Features Hydraulics Parker 8200 Series couplings feature: Unique valve design permits connection while either or both the coupler and nipple are under pressure. ouble acting sleeve for one handed push-to-connect operation when coupler is clamp or bulkhead mounted. ritical parts are hardened for durability. ependable ball locking mechanism holds the mating halves together. ouplers and nipples are precision machined from solid bar stock. The mating 8010 series nipples meet ISO 5675 requirements. pplications The 8200 Series brings to the industry a proven design for use on construction equipment, forestry equipment, agricultural machinery, oil tools, steel mill machinery, and other demanding hydraulic applications. Specifications ody Size (in.) 1/2 Rated Pressure (PSI) 3000 Rated Flow (GPM) 12 Temperature Range (std seals) -40 to +250 F Note: Protective dust plugs and caps play a crucial role in the life of a quick coupling and no purchase of a hydraulic quick coupling is complete without the selection of an appropriate dust plug and cap. See pages noted in Table of ontents for dust plugs and caps for the Parker full line of hydraulic couplings. Special Order Information Standard seal material is Nitrile, other seal options are available. See Ordering Information at end of Section and Fluid ompatibility hart at end of this catalog for assistance in making seal selection. Performance Pressure rop in PSI Series (1/2") Test Fluid: Oil SUS 1/2" Flow in USGPM -36

81 Hydraulic Quick ouplings onnect Under Pressure ouplings 8200 Series ouplers Female Thread ody Part Thread Thread imensions (in.) Size No. Size Size Overall Wrench Largest Wt. (L.) (in.) Steel NPSF OR Length Flats iameter P/Piece 1/ / / / / / Hydraulics Nipples Female Thread ody Part Thread Thread imensions (in.) Size No. Size Size Overall Exposed Hex Largest Wt. (L.) (in.) Steel NPTF OR Length Length Size iameter P/Piece E F G 1/ / / P* 1/ E G 1/ / / P* 3/ / / / P* 7/ * Poppet design F Replacement Parts Series ody Size (in.) Part Number escription Material 1/ Q-Ring Nitrile -37

82 Hydraulic Quick ouplings onnect Under Pressure ouplings 9200 Series Hydraulics Pressure rop in PSI pplications The Parker 9200 lever coupling is designed with a leveroperated cam that opens and closes the valves in both coupling halves, positively locking them into place. This allows the couplings to be easily connected and disconnected while under pressure. The 9200 couplings can functionally replace a ouble Shut-Off quick coupling and two high pressure ball valves. y simply turning the lever to the closed position the hydraulic lines on a piece of machinery or mobile equipment may be disconnected either for maintenance or equipment changeovers. Note: Protective dust plugs and caps play a crucial role in the life of a quick coupling and no purchase of a hydraulic quick coupling is complete without the selection of an appropriate dust plug and cap. See pages noted in Table of ontents for dust plugs and caps for the Parker full line of hydraulic couplings. Performance Series (1/2") Test Fluid: Oil SUS Flow in USGPM 1/2" Features The lever operates a cam that mechanically locks both valves into either the open or closed position. losed, the flow is shut off at the coupler, allowing easy zero-pressure connect and disconnect. Open, the valves are locked in the open position in both coupler and nipple. In this position the valves are unaffected by hydraulic surges. 2. Parker design eliminates back flow-checking. The positive lock of the cam prevents hydraulic surges from forcing the valve closed, which avoids flow checking and disrupting equipment performance. 3. Valves close automatically if coupling is accidentally disconnected. 4. The 8010 Series nipples used with the 9200 coupler is an industry standard that meets ISO 5675 requirements. 5. Rugged, reliable ball valve and induction hardened locking ball groove prevent rinelling and prolong coupling life. 6. Turning the lever without the nipple in place will NOT result in oil flow. 7. The Lever oupler is covered by patent numbers: # and # New easy action sleeve aids connect and disconnect. Specifications ody Size (in.) 1/2 Rated Pressure (PSI) 3000 Rated Flow (GPM) 12 Temperature Range (std seals) -40 to +250 F -38

83 Hydraulic Quick ouplings onnect Under Pressure ouplings 9200 Series ouplers ody Part Thread imensions (in.) Size No. Size Overall Wrench Largest Wt. (L.) (in.) Steel NPTF OR Length Flats iameter P/Piece 1/ / / / / / / / *1/ / Hydraulics * Mates with the 1/4" 60 Series Nipples. Nipples ody Part Thread Thread imensions (in.) Size No. Size Size Overall Exposed Hex Largest Wt. (L.) (in.) Steel NPTF OR Length Length Size iameter P/Piece E F G 1/ / E G 1/ P* 1/ / / / P* 3/ / / / P* 7/ F * Poppet design Replacement Parts 9200 Series ody Size (in.) 1/2 O-Rings - Nitrile

84 Hydraulic Quick ouplings onnect Under Pressure ouplings 5000 Series Features Hydraulics The Parker 5000 Series coupling features: Two-piece coupler body that permits operation while one or both halves are under pressure as well as when there is no pressure in either half. onnect under pressure by unscrewing the valve body until two or three threads are visible. Nipple can be inserted and locked into the coupler without opening either valve. (Use a wrench to thread the valve body back into the coupler, the valves are opened against internal pressure. If internal pressure makes manual disconnect difficult, unscrewing the valve body from the coupler will permit the valves to close, thereby relieving internal pressure and allowing manual operation of the ball-locking sleeve.) The mating 8010 series nipples meet ISO 5675 requirements. pplications The Parker 5000 Series is an economical coupling that is a threaded union and can be connected under pressure with tools. For applications that require a coupling to be connected under-pressure and where tools can be used to make the connection, the 5000 Series coupling should be considered. Note: Protective dust plugs and caps play a crucial role in the life of a quick coupling and no purchase of a hydraulic quick coupling is complete without the selection of an appropriate dust plug and cap. See pages noted in Table of ontents for dust plugs and caps for the Parker full line of hydraulic couplings. Performance 5000 Series (1/2") Test Fluid: Oil SUS Pressure rop in PSI /2" Specifications Flow in USGPM ody Size (in.) 1/2 Rated Pressure (PSI) 2500 Rated Flow (GPM) 12 Temperature Range (std seals) -40 to +250 F -40

85 Hydraulic Quick ouplings onnect Under Pressure ouplings 5000 Series oupler E ody Part Thread imensions (in.) Size No. Size Overall Wrench Wrench Largest Wt. (L.) (in.) Steel NPTF Length Length Flats Flats iameter P/Piece E 1/ / Hydraulics Nipple E ody Part Thread imensions (in.) Size No. Size Overall Exposed Hex Largest Wt. (L.) (in.) Steel NPTF OR Length Length Size iameter P/Piece E F G 1/ / / / / / G F Replacement Parts 5000 Series ody Size (in.) 1/2 O-Rings - Nitrile

86 Hydraulic Quick ouplings High Pressure ouplings 3000 Series Hydraulics pplications Parker 3000 Series couplings with their threaded union locking system and precision ball-type check valves, are designed for extreme high pressure applications such as found on portable hydraulic rams. See pages noted in Table of ontents for dust plugs and caps for the Parker full line of hydraulic couplings. Note: Protective dust plugs and caps play a crucial role in the life of a quick coupling and no purchase of a hydraulic quick coupling is complete without the selection of an appropriate dust plug and cap. See pages noted in Table of ontents for hydraulic couplings dust plugs and caps for the full line of hydraulic couplings. Features 1. Machined from solid steel barstock for durability. 2. The 3000 Series employs a threaded sleeve locking mechanism, mates with matching male threads on the nipple. The two halves must be manually threaded together for connection. 3. Hard, chrome alloy balls are used for valving. They are spring loaded for positive seating of the valve. 4. The valve provides a metal-to-metal seal between the ball and a coined seat. 5. The interface seal is polyurethane which resists high pressure extrusion. 6. threaded valve retainer provides a valve stop that assures positive valve alignment. Performance Specifications ody Size (in.) 1/4 3/8 Rated Pressure (PSI) Static 10,000 10,000 Rated Flow (GPM) 3 6 Temperature Range (std seals) -22 to +230 F Pressure rop in PSI Series (1/4", 3/8") Test Fluid: Oil SUS 1/4" 3/8" Flow in USGPM -42

87 Hydraulic Quick ouplings High Pressure ouplings 3000 Series ouplers ody Thread imensions (in.) Size Part Size Overall Wrench Largest Wt. (L.) (in.) No. NPTF Length Flats iameter P/Piece 1/ /4-18 (Male) / /8-18 (Male) / /8-18 (Female) Hydraulics Nipples E ody Part Thread imensions (in.) Size No. Size Overall Expose Hex Largest Wt. (L.) (in.) Steel NPTF Length Length Size iameter P/Piece E F G 1/ /4-18 (Female) / /8-18(Female) / /8-18 (Male) G F -43

88 Hydraulic Quick ouplings High Pressure ouplings T Series Features Hydraulics Specifications ody Size (in.) 3/8 Rated Pressure (PSI) 10,000 Rated Flow (GPM) 6 Temperature Range (std seals) -15 to +400 F Performance T Series (3/8") Test Fluid: Oil SUS Positive valve stop. The perch maintains valve alignment and provides metal to metal valve stop to insure that the valves open full every time. Precision machined valves with elastomeric seals provide for positive shut-off upon disconnection. Hardened nipples and sleeves and solid barstock construction make for a quality coupling with maximum resistance to damage from hydraulic and mechanical shock. urable ball-locking mechanism assures reliable connection every time. large number of locking balls distributes the work load evenly while providing alignment and swiveling action to reduce hose torque and prolong hose life. UTION: These products are not to be used as swivels, rotation under pressure will result in excessive and premature wear. Female pipe (NPSF) standard. The standard Fluorocarbon seal is designed to withstand extremely high pressures and provide reliable sealing. PTFE back-up ring provides support for the seal in high pressure applications. Sleeve locking mechanism prevents accidental disconnection when the coupling is dragged along the ground. Steel construction, hromium-6 Free plating for corrosion resistance. Pressure rop in PSI /8" pplications Parker T series couplings are found in the construction, railway maintenance and house moving industries. Used on hydraulic jacking equipment, these couplers eliminate costly down time caused by improperly connected threaded types. For use where high pressure capability is required coupled with positive coupling action. onsiderably faster to use than threaded types Flow in USGPM Note: Protective dust plugs and caps play a crucial role in the life of a quick coupling and no purchase of a hydraulic quick coupling is complete without the selection of an appropriate dust plug and cap. See pages noted in Table of ontents for dust plugs and caps for the Parker full line of hydraulic couplings. oupler ody Fitting imensions (in.) Size Part Thread Overall Hex Largest Wt. (L.) (in.) No. Size Length Size iameter P/Piece 3/8 T-371 3/8-18 NPSF Nipple F G ody Fitting imensions (in.) Size Part Thread Overall Exposed Hex Largest Wt. (L.) (in.) No. Size Length Length Size iameter P/Piece E F G 3/8 T-372 3/8-18 NPSF E NPSF National Pipe Straight Fuel -44

89 Hydraulic Quick ouplings High Pressure ouplings 1141 Series oupler ody Thread Size Part Size imensions Wt. (L.) (in.) No. NPTF (in.) P/Piece 1/ / Hydraulics pplications The 1141 Series is a general purpose coupling for high pressure connect-under-pressure applications. Features 303 Stainless steel body. rass locking sleeve Polyurethane seals to resist extrusion and abrasion. Self locking threads help prevent coupling from accidentally disconnecting. Visual makeup when fully coupled the edge of the sleeve will be flush with the end of the male thread giving a visual check for complete coupling. Small diameter mating seal helps keep separation forces to a minimum, allowing for easier connect and disconnect at pressures up to 5,000 PSI. 10,000 PSI working pressure, 17,000 PSI intermittent pressure. ust caps and plugs included. Nipple ody Thread Size Part Size imensions Wt. (L.) (in.) No. NPTF (in.) P/Piece 1/ / Specifications ody Size (in.) 1/4 Rated Pressure (PSI) 10,000 Rated onnect-under-pressure apability (PSI) 5000 Rated Flow (GPM) 3 Temperature Range (Polyurethane seals) -30 to +180 F Vacuum test 20 in/hg Torque to connect at 1000 PSI 47 in/lbs. -45

90 Hydraulic Quick ouplings Mold oolant Line ouplings Moldmate Series pplications Hydraulics Parker moldmate couplings are specifically designed for connecting coolant lines to molds and dies, on injection molding machinery in the plastics and die casting industries. Moldmate couplings significantly reduce machine downtime by providing fast and easy connection of coolant lines during mold changes. Their short nipples can be recessed below the surface of the mold for more efficient storage of molds. Moldmate couplers are available with or without valves in the female half. Non-valved couplers provide maximum flow for efficient cooling. Valved couplers shut off when disconnected. Special Order Information Standard seal material is Silicone and is compatible with water and water glycol fluids commonly used in heat transfer systems. Fluorocarbon seals are available for use only with oil-based media and not with water glycol. To specify a Fluorocarbon seal, add the suffix Y to the standard moldmate part number, thus: P206Y. Selection Guidelines Moldmate couplings are designed for a maximum working pressure of 200 PSI. Most thermoplastic and thermoset heat transfer systems have pumps which provide relatively high flow rates at relatively low pressures. Water and water glycol systems usually have capacities ranging from 10 to 40 gpm, with most from 10 to 15 gpm. Normal medial opening pressures are 20 to 60 PSI for these systems. Heat transfer systems using oil generally operate from 10 to 30 PSI. However, their flow rates are usually much higher, requiring the total volume of oil to be circulated at least once per minute. The number of hose connections in a single mold system results in a cumulative pressure drop. Please note the Pressure rop vs. Flow Rate chart provided, to select the appropriate size. Temperature is another important consideration. Parker moldmate couplings with their standard Silicone seal have a temperature capability of -90 to +400 F. Rapid deterioration of the seal and leakage may result if used beyond these limits. External conditions of temperature, corrosive atmospheres, and other abnormalities may affect coupling performance and must be considered when selection is made. onsult factory with questions. Pressure rop in PSI Specifications ody Size (in.) 1/4 3/8 1/2 Rated Pressure (PSI) Rated Flow (GPM) Material Standard Silicone seal *Optional Fluorocarbon seal * For use with oil based media only Performance /4" Valved Moldmate Series (1/4", 3/8", 1/2") Test Fluid: Water (Straight oupler) 1/4" Non-valved 3/8" Valved Temperature Range -90 to +400 F -15 to +400 F 3/8" Non-valved 1/2" Non-valved Flow in USGPM -46

91 Hydraulic Quick ouplings Mold oolant Line ouplings Moldmate Series Features 3 ouplers Straight 45 egree vailable with or without valves in the coupler. Non-valved couplers have minimum flow resistance for maximum cooling. Valved couplers shut off automatically upon disconnect. Valved couplers can be used with either valved or non-valved nipples. valved nipple, however, must be used with a valved coupler. 2. Nipples are designed to be recessed below mold surfaces to provide more efficient storage of molds and prevent damage to the nipple. 3. Widest choice of end fittings available, including straight, 45 or 90 with standard hose barb or Push-Lok barbs for easy installation. 4. ouplers and nipples are made of corrosion resistant brass, and valved couplers or valved nipple have a Fluorocarbon O-ring on poppet and Silicone interface seal as standard for use with water glycol type fluids commonly used in heat transfer systems. 5. Silver colored sleeve designates valved coupler. ody Part No. Part No. imensions (in.) Size rass Wt. (L.) rass Wt. (L.) Hose Overall Largest Overall Hex Largest (in.) Non-valved P/Piece Valved P/Piece I.d. Length iameter Length Size iameter Non-valved Valved 1/4 P P204V / /4 P204-P* 0.10 P204V-P / /4 P P205V / /4 P P206V / /4 P206-P* 0.11 P206V-P / /8 P P306V / /8 P306-P* 0.26 P306V-P / /8 P P308V / /8 P308-P* 0.25 P308V-P / /2 P N 1/ /2 P504-P* 0.50 N 1/ /2 P N 3/ /2 P506-P* 0.52 N 3/ N = Not vailable ody Part No. Part No. imensions (in.) Size rass Wt. (L.) rass Wt. (L.) Hose Overall Hex Largest Overall Hex Largest (in.) Non-valved P/Piece Valved P/Piece I.. Length Size iameter Length Size iameter Non-valved Valved 1/4 P P224V / /4 P224-P* 0.13 P224V-P / /4 P P226V / /4 P226-P* 0.26 P226V-P / /8 P P326V / /8 P326-P* 0.34 P326V-P / /8 P P328V / /8 P328-P* 0.34 P328V-P / /2 P N 1/ /2 P524-P* 0.78 N 1/ /2 P N 3/ /2 P526-P* 0.80 N 3/ * Suffix P in part number denotes Push-Lok hose barb. Without suffix denotes standard hose barb. Push-Lok hose barbs are designed for use with Parker Push-Lok hose and do not require clamps. Valved ouplers can be used with either non-valved or valved nipples. Hydraulics -47

92 Hydraulic Quick ouplings Mold oolant Line ouplings Moldmate Series Hydraulics 90 egree ody Part No. Part No. imension (in.) imensions (in.) Size rass Wt. (L.) rass Wt. (L.) Hose Overall Hex Largest Overall Hex Largest (in.) Non-valved P/Piece Valved P/Piece I.. Length Size iameter Length Size iameter Non-valved Valved 1/4 P P214V / /4 P214-P* 0.14 P214V-P / /4 P P215V / /4 P P216V / /4 P216-P* 0.16 P216V-P / /8 P P316V / /8 P316-P* 0.37 P316V-P / /8 P P318V / /8 P318-P* 0.37 P318V-P / /2 P N 1/ /2 P514-P* 0.83 N 1/ /2 P N 3/ /2 P516-P* 0.84 N 3/ * Suffix P in part number denotes Push-Lok hose barb. Without suffix denotes standard hose barb. Push-Lok hose barbs are designed for use with Parker Push-Lok hose and do not require clamps. Valved ouplers can be used with either non-valved or valved nipples. Sub ssemblies and Individual Replacement Parts Non-valved Sub-assembly (rass Sleeve) Part No. Thread imensions (in.) ody rass Wt. (L.) Size Overall Hex Largest Size (in.) For No-valving P/Piece NPTF Length Size iameter 1/4 P / /8 P / /8 P HF / /2 P / Valved* Sub-assembly (Silver olored Sleeve) Part No. Thread imensions (in.) ody rass Wt. (L.) Size Overall Hex Largest Size (in.) For Valving P/Piece NPTF Length Size iameter 1/4 P / /8 P / *odies are designed for use with valves retained by a male pipe fitting (i.e. hose barb). Order valves and valve springs seperately. Valves (for Valved Sub-assembly) ody Size (in.) Part No. Material 1/ rass 3/8 P300-11S rass Valve Springs (for Valved Sub-assembly) ody Size (in.) Part No. Material 1/ Stainless 3/8 P300-6 Stainless Replacement Seals (for both Valved and Non-valved) Seal Material ody Size (in.) 1/4 ody Size (in.) 3/8 ody Size (in.) 1/2 * Silicone P200-9 P300-9 P500-9 * Fluorocarbon P200-9Y P300-9Y * Please note: ulk seals are considered to be non-returnable. ssembly Instruction Sheet (for all sizes & configurations) Order Part Number

93 Hydraulic Quick ouplings Mold oolant Line ouplings Moldmate Series Nipples Female Pipe Thread E G ody Part Wt. (L.) Part Wt. (L.) Thread imensions (in.) Size No. P/Piece No. P/Piece Size Overall **Exposed Hex Largest (in.) rass rass Steel Steel NPTF Length Length Size iameter E F G 1/4 PN251F 0.02 PN251F / /4 PN252F 0.05 PN252F / /4 PN253F 0.08 PN253F / /8 PN352F 0.05 PN352F / /8 PN353F 0.07 PN353F / Hydraulics Male Pipe Thread ody Part Wt. (L.) Part Wt. (L.) Thread imensions (in.) Installation Size No. P/Piece No. P/Piece Size Overall **Exposed Hex Largest Recess (in.) rass rass Steel Steel NPTF Length Length Size ia. ia. epth E F G F E Male Nipple Installation G 1/4 PN / /4 PN PN251S / /4 PN PN252S / /4 PN PN253S / /8 PN PN352S / /8 PN PN353S / /8 PN N 1/ /2 PN N 3/ /2 PN N 1/ /2 PN N 3/ Valved Nipple E ody Part Thread imensions (in.) Installation Size No. Size Overall **Exposed Hex Largest Recess Wt. (L.) (in.) rass NPTF Length Length Size ia. ia. epth P/Piece E F G 1/4 PV252* 1/ /8 PV353* 3/ *Valved Nipple must be used with Valved oupler. **This dimension represents the portion of the nipple that is exposed when inserted into a moldmate coupler. G F -49

94 Hydraulic Quick ouplings Mold oolant Line ouplings Moldmate Series Hydraulics Moldmate Extension Nipples E G F ody Part Thread imensions (in.) Wt. Size No. Size Overall Hex Largest (L.) (in.) rass NPTF Length Length Size ia. P/Piece E F G 1/4 PN / / /4 PN / / /4 PN / / /4 PN / / /4 PN / / /4 PN / / /4 PN / / /4 PN / / /4 PN / / /4 PN / / /4 PN / / /4 PN / / /4 PN / / /8 PN / / /8 PN / / /8 PN / / /8 PN / / /8 PN / / /8 PN / / /8 PN / / /8 PN / / /8 PN / / /8 PN / / /8 PN / / /8 PN / / /8 PN / / /8 PN / / /8 PN / /

95 Hydraulic Quick ouplings High Flow ouplings ST Series pplications The Parker ST Series are non-valved couplings for applications where maximum flow is required. Their smooth, open bore offers the lowest pressure drop of any quick coupling design and is ideal for applications such as high-pressure water and steam washers, carpet cleaners and mold coolant lines and many other non-valved applications. Specifications Hydraulics ody Size (in.) 1/8 1/4 3/8 1/2 3/ /4 1 1/2 Rated Pressure (PSI) rass plr/npl rass plr/steel Npl SS plr/npl Rated Flow Temperature Range (std seals) -40 to +250 F Performance 12 ST Series (1/8", 1/4", 3/8", 1/2") Test Fluid: Oil SUS ST Series (3/4", 1", 1-1/4") Test Fluid: Oil SUS 5 Pressure rop in PSI /8" 1/4" 3/8" 1/2" Pressure rop in PSI /4" 1" 1-1/4" Flow in USGPM Flow in USGPM -51

96 Hydraulic Quick ouplings High Flow ouplings ST Series Features Hydraulics The smooth, open bore with no valving in either half offers minimal pressure drop and allows easy cleaning in applications where the same lines are used for more than one media. ST couplers and nipples are machined from solid barstock, providing a quality coupling that is durable. ST couplers are available in brass and 303 stainless steel as standard product materials. ST nipples are available in 303 stainless steel, brass and hromium-6 Free plated steel. The ball locking grooves of the steel ST nipples are case hardened for resistance to brinelling where high cycle rates and pressure surges are encountered. The ST is an "Interchange" coupling since it dimensionally and functionally interchanges with similar couplings made by other manufacturers. Special Order Information ouplers Female Pipe Thread ll sizes of ST Series can be furnished with locking sleeves. Place suffix letters SL (Sleeve-Lok) after regular catalog numbers. Example: SST-4MSL. Standard seal material is Nitrile. Ethylene Propylene, Fluorocarbon, or Neoprene seals are available upon request. See Fluid ompatibility hart for recommendations. ody Part No. Part No. Thread imensions (in.) Size Wt. (L.) Type 303 Wt. (L.) Size Overall Wrench Largest (in.) rass P/Piece Stainless P/Piece NPTF Length Flats iameter 1/8 ST SST / /4 ST SST / /8 ST SST / /2 ST SST / /4 ST SST / ST SST / /4 ST /4-11 1/ /2 ST /2-11 1/ Male Pipe Thread ody Part No. Part No. Thread imensions (in.) Size Wt. (L.) Type 303 Wt. (L.) Size Overall Wrench Largest (in.) rass P/Piece Stainless P/Piece NPTF Length Flats iameter 1/8 ST-1M 0.05 SST-1M / /4 ST-2M 0.16 SST-2M / /8 ST-3M 0.25 SST-3M / /2 ST-4M 0.34 SST-4M / /4 ST-6M SST-6M / ST-8M 0.85 SST-8M /

97 Hydraulic Quick ouplings High Flow ouplings ST Series Nipples Female Pipe Thread E G ody Part Part Part No. Thread imensions (in.) Size No. Wt. (L.) No. Wt. (L.) Type 303 Wt. (L.) Size Overall Exposed Hex Largest (in.) rass P/Piece Steel P/Piece Stainless P/Piece NPTF Length Length Size ia. F E F G 1/8 ST-N ST-N SST-N / /4 ST-N ST-N SST-N / /8 ST-N ST-N SST-N / /2 ST-N ST-N SST-N / /4 ST-N ST-N SST-N / ST-N ST-N SST-N / /4 ST-N /4-11 1/ /2 ST-N /2-11 1/ Hydraulics Nipples Male Pipe Thread E G F ody Part Part Part No. Thread imensions (in.) Size No. Wt. (L.) No. Wt. (L.) Type 303 Wt. (L.) Size Overall Exposed Hex Largest (in.) rass P/Piece Steel P/Piece Stainless P/Piece NPTF Length Length Size ia. E F G 1/8 ST-N1M 0.02 ST-N1M 0.02 SST-N1M / /4 ST-N2M 0.06 ST-N2M 0.05 SST-N2M / /8 ST-N3M 0.08 ST-N3M 0.07 SST-N3M / /2 ST-N4M 0.15 ST-N4M 0.13 SST-N4M / /4 ST-N6M 0.23 ST-N6M 0.21 SST-N6M / ST-N8M 0.46 ST-N8M 0.43 SST-N8M / /4 ST-N10M /4-11 1/ /2 ST-N12M /2-11 1/ Replacement Parts ST Series ody Size (in.) ST Series O-Rings 1/8 1/4 3/8 1/2 Standard Nitrile* ody Size (in.) ST Series O-Rings 3/ /4 1-1/2 Standard Nitrile* * Other compounds available are Ethylene Propylene, Fluorocarbon, Neoprene (ontact the division for compound availability) -53

98 Hydraulic Quick ouplings High Flow ouplings Water Service Series pplications Hydraulics Parker Water Service ouplings are used anywhere water hoses are connected and disconnected frequently. They are used on a wide variety of applications including garden hoses, wash down systems, and mobile water tank lines. The unvalved design permits maximum flow with minimum pressure drop. Specifications ody Size (in.) 3/4" Rated Pressure (PSI) 200 Rated Flow (GPM) 28 Temperature Range (std seals) -40 F to +250 F Features rass and stainless steel construction for heavy duty service. urable 4-ball locking mechanism for secure connections. Quality, temperature-resistant Nitrile seals for a leak-free service life. oupler ody Part Thread Size Overall Length Largest iameter Wt. (L.) Size (in.) No. NH P/Piece 3/ /4-11 1/ Nipple E ody Part Thread Size Overall Length Exposed Length Wt. (L.) Size (in.) No. NH E P/Piece 3/ /4-11 1/

99 Hydraulic Quick ouplings High Flow ouplings HO Series pplications HO Series couplings are used in a wide variety of applications. HO couplings are used in refineries, petrochemical plants and paper and pulp mills for connecting hose lines for high pressure hydro-blasting of boilers and pipe lines. They are also used in oil fields on hose lines for internal and external pressure testing of tubing. Note: Protective dust plugs and caps play a crucial role in the life of a quick coupling and no purchase of a hydraulic quick coupling is complete without the selection of an appropriate dust plug and cap. See pages noted in Table of ontents for hydraulic couplings dust plugs and caps for the full line of hydraulic couplings. Hydraulics Specifications ody Size (in.) 1/4 3/8 1/2 Rated Pressure (PSI) 15,000 15,000 10,000 Rated Flow (GPM) Temperature Range (std seals) -40 to +250 F Features For high pressure applications: working pressures to 15,000 PSI (1,050 ar) for the 1/4 and 3/8 sizes; to 10,000 PSI (700 ar) for the 1/2 size. No internal valving to restrict flow. Made of steel with electroless nickel plating for corrosion resistance. Standard sleeve-lock feature which helps prevent accidental disconnect. Standard Nitrile ody O-Ring. acked up by PTFE washer to prevent seal extrusion. ouplers ody Thread imensions (in.) Size Part Size Overall Hex Largest Wt. (L.) (in.) No. NPSF Length Size iameter P/Piece 1/4 HO-251-4FP 1/ /8 HO-371-6FP 3/ /2 HO-501-8FP 1/ Nipples ody Thread imensions (in.) Size Part Size Overall Exposed Hex Largest Wt. (L.) (in.) No. NPSF Length Length Size iameter P/Piece E F G E F G 1/4 HO-252-4FP 1/ /8 HO-372-6FP 3/ /2 HO-502-8FP 1/ NPSF National Pipe Straight Fuel -55

100 Hydraulic Quick ouplings Special Purpose ouble Shut-Off M Series pplications Typical applications include dental equipment, lubrication equipment, fluid transfer and coolant lines. Hydraulics Specifications ody Size (in.) 1/8" Temperature Range -15 F to +400 F Rated Pressure 250 PSI Locking evice 5 alls Rated Flow (GPM) 0.8 How To Order M FP Features Parker M Series offer double shut-off valving and push-toconnect operation in a small envelope size. They are constructed of nickel plated brass and are available in 1/8" body size only. Standard seals are Fluorocarbon, but other seal material is available upon request. See the oupling Selection and Ordering Information Guide at the beginning of Section and the Fluid ompatibility hart at the end of this catalog for optional materials. Performance 12 M Series (1/8") Test Fluid: Water M Series Port Size (1/16 of a inch) 1= Valved oupler 2= Valved Nipple 1/8" ody Size FP= Female NPT MP= Male MPT 10 Pressure rop in PSI /8" Flow in USGPM -56

101 Hydraulic Quick ouplings Special Purpose ouble Shut-Off M Series ouplers Female Pipe Thread ody New Old Thread imensions (in.) Size Part Part Size Overall Hex Largest Wt. (L) (in.) No. No. NPTF Length Size iameter P/Price 1/8 M-121-2FP M02-2-2Y 1/ /8 M-121-4FP M02-2-4Y 1/ Hydraulics Male Pipe Thread ody New Old Thread imensions (in.) Size Part Part Size Overall Hex Largest Wt. (L) (in.) No. No. NPTF Length Size iameter P/Price 1/8 M-121-2MP M01-2-2Y 1/ /8 M-121-4MP M01-2-4Y 1/ Nipples Female Pipe Thread E G F ody New Old Thread imensions (in.) Size Part Part Size Overall Exposed Hex Largest Wt. (lb) (in.) No. No. NPTF Length Length* Size iameter P/Price E F G 1/8 M-122-2FP NM02-2-2Y 1/ /8 M-122-4FP NM02-2-4Y 1/ * This dimension represents the portion that is exposed when a nipple is inserted into a Parker M Series coupler. Male Pipe Thread F E G ody New Old Thread imensions (in.) Size Part Part Size Overall Exposed Hex Largest Wt. (lb) (in.) No. No. NPTF Length Length* Size iameter P/Price E F G 1/8 M-122-2MP NM01-2-2Y 1/ /8 M-122-4MP NM01-2-4Y 1/ * This dimension represents the portion that is exposed when a nipple is inserted into a Parker M Series coupler. -57

102 Hydraulic Quick ouplings ust Plugs and ust aps pplications Hydraulics Parker offers a selection of dust plugs and caps for their hydraulic quick couplings. Most series shown in this section have a dust plug and cap specifically designed to be used with that style of coupling. ust plugs and caps serve a twofold function. They keep the mating surface clean and free of contamination and protect the critical mating elements of the coupling halves when they are disconnected. In this way the nipple is protected from damage that would make the total coupling unusable. Protective dust plugs and caps play a crucial role in the use of quick couplings and no purchase of a hydraulic quick coupling is complete without the selection of an appropriate dust plug and cap. When ordering the dust cap/plug body size must correspond to that of the coupler or nipple. Parker s full line of dust plugs and caps can be found below and on the following pages. ust Plug: ust ap: Used on oupler (female half) Used on Nipple (male half) ust Plugs 60 Series ody ust Plug ust Plug ust ap ust ap Size Part No. Part No. Part No. Part No. (in.) luminum Rubber luminum Rubber 1/8 H1-65 H1-65M H1-66 H1-66M 1/4 H2-65 H2-65M H2-66 H2-66M 3/8 H3-65 H3-65M H3-66 H3-66M 1/2 H4-65 H4-65M H4-66 H4-66M 3/4 H6-65 H6-65M H6-66 H6-66M 1 H8-65 H8-65M H8-66 H8-66M 1 1/2 H12-65 N H12-66 N 2 1/2 H20P-65 N H20P-66 N N = Not vailable 6600 Series ody ust Plug ust ap Size Part No. Part No. (in.) Rubber Rubber 1/4 H1-65M H1-66M 3/8 TR-37 TR-37 1/ M M 3/ M M M M SM Series ody Size ust Plug ust ap (in.) Part No. Part No. Material 1/4 PL-25 N/ Plastic 1/4 PR-25 R-25 Rubber 1/4 P luminum 1/2 P Rubber 1/2 P luminum 3/4 P luminum -58

103 Hydraulic Quick ouplings ust Plugs and ust aps HP Series 4000 Series & 5000 Series ody ust Plug ust ap Size Part Number Part No. (in.) luminum luminum 1 HPP-100 HP /2 HPP-150 HP-150 ody ust Plug ust Plug ust ap ust ap Size Part No. Part No. Part No. Part No. (in.) Steel Rubber Steel Rubber 1/ M* M* 3/ M* M* 1/ M* M* 3/ M* M* M* M* * esignates all rubber material. (Not shown at left) Hydraulics NS Series ody Size Part Number (in.) Rubber 3/8 NR-37 1/2 NR-50 3/4 NR-75 1 NR-100 Protective cover fits either half. FF Series, F Series, FH Series & FS Series ody ust Plug ust ap Size Part Number Part No. (in.) Rubber Rubber 1/4* FR-25 FR-25 3/8 NR-50 NR-37 1/2 FR-501 FR-502 3/4 FR-751 FR FR-1001 FR-1002 * FR-25 fits both halves FE Series, FEM Series ody ust Plug ust ap Size Part Number Part No. (in.) Rubber Rubber 1/4 FR-25 FR-25 3/8 NR-50 NR-37 1/2 FR-501 FER-502 3/4 FR-751 FER FR Series ody ust Plug ust ap Size Part No. Part No. (in.) rass rass 3/ / /

104 Hydraulic Quick ouplings ust Plugs and ust aps 9200 Series ody ust ap. Size Part No. (in.) Rubber 1/ Hydraulics 3000 Series ody ust Plug ust ap Size Part No. Part No. (in.) Steel Steel 1/ / T Series ody Size Part Number (in.) Rubber 3/8 TR-37 Protective cover fits either half. HO Series TR-37 Plug / ap -50 ody Size Used With ust Plug ust ap (in.) HO Series Part No. Part No. Material oupler/nipple Part No. 1/4 HO-251/252-4FP TR-37 TR-37 Rubber 3/8 HO-371/372-6FP TR-37 TR-37 Rubber 1/2 HO-501-8FP P-50 - Rubber 1/2 HO-502-8FP Rubber -60

105 Hydraulic Quick ouplings Ordering Information When ordering Parker coupler bodies and nipples, please state the part number of each type of coupler body and each type of nipple desired. List coupler bodies and nipples as separate items rather than in combinations. e sure to double check thread or hose sizes of items required. Many of Parker s coupling products are available with unique non-standard options well suited to very specific applications. Examples of unusual end use applications might include: high temperatures (above 250 F), extremely caustic/corrosive solutions passing through the coupling, external/environmental corrosion situations, or other high wear and tear situations such as dragging the product along the ground. Please see the Fluid ompatibility hart at the end of the catalog for a guide in selecting material for various media. It is always recommended that the Quick oupling ivision be contacted with any questions concerning specific product application needs. Typically, a prefix or suffix is added to the base part number to specify a non-standard O-ring seal, or special option such as a sleeve lock. The Optional Seals Suffix chart illustrates the designations. Please Note: ertain couplings series have additional "Special Order Information" which should be referred to in ordering those products. If applicable to the product, "Special Order Information" is found next to the Features and Specifications charts. Operation Prefix H for heavy duty nipple Suffix SL for coupler sleeve-lok Suffix P for poppet valve Suffix P for Push-lok hose barb Suffix V for Valve ctuator Optional Seals Suffix* No suffix is required when ordering products with the standard Nitrile seals. When specifying an optional seal, refer to the following chart to determine the appropriate suffix.** oupling Series Ethylene Fluoro- Neoprene Perfluoro- Propylene carbon elastomer 60 Series W Y Z **** 6600 Series W Y Z **** SM Series E5 E4 E12 **** HP Series E5 E4 E12 **** 4000 Series W Y Z N/ 4200 Series W Y Z N/ NS Series E5 E4 N/ **** FF Series E5 E4 N/ **** Std. is E49 FH Series E5 E4 N/ **** FS Series E5 ST E12 **** 6100 Series W Y Z N/ 5000 Series W Y Z N/ 8200 Series W Y Z N/ 9200 Series W Y Z N/ 3000 Series T Series 1141 Series vailable with Polyurethane only (no suffix needed) vailable with Fluorocarbon only (no suffix needed) vailable with Polyurethane only (no suffix needed) ST Series W Y Z Water Service vailable with Nitrile only HO Series E5 E4 E12 N/ Moldmate Series N/ Y*** N/ N/ Std. is Silicone Hydraulics *To select proper seal materials, see Fluid ompatibility hart in ppendices section, or contact your Parker Quick oupling istributor. **N/ = Not vailable; ST = Standard (No Suffix Needed) *** Fluorocarbon seal available for use only with oil based media, not water glycol. **** ontact the division for Perfluoroelastomer Seal Options. -61

106 Hydraulic Quick ouplings Promotional Products Hydraulics escription These popular coupling key chains are now available from the. The new key chains are an anodized aluminum construction available in an array of colors. Key chains can be ordered using part numbers in the following chart. Part Number KEY-K KEY-U KEY-GR KEY-R KEY-L KEY-NI Sleeve olor lack lue Green Red lear Old style nickel plated -62

107 Thermoplastic ouplings Thermoplastics -1

108 Thermoplastic ouplings Table of ontents Thermoplastics oupling Selection Guide...-3 Spectrum Series...-4 Specifications...-4 ouplers...-5 Nipples - Unvalved...-6 Nipples - Valved...-7 PF Series...-8 Specifications...-8 ouplers...-9 Nipples...-9 ust aps and Plugs...-9 Ordering Information

109 Thermoplastic ouplings oupling Selection Guide PF Series Valving Flush Face Non-Spill ody Size (in.) Material 1/2", 1"& 2 Polypropylene/ Stainless Locking Mechanism Pawl lock oupler Style Push-to- onnect Std. Seal Material Fluorocarbon Temp Range** Rate Pressure +40 to +140 F 30 to 100 PSI Spectrum TM Series Valved or Unvalved Spectrum TM Series Valved or Unvalved Spectrum TM Series Valved or Unvalved Ordering Information Optional Seals Suffix* Push-to- onnect Push-to- onnect Push-to- onnect 1/8" & 3/8" cetal 316 SS Finger Lock Nitrile 0 F to 180 F 0 to 145 PSI 1/8" & 3/8" PVF/SS Finger Lock Fluorocarbon 0 F to 250 F 0 to 115 PSI 316 SS 3/8" PVF/ Finger Lock Fluorocarbon 0 F to 250 F 15 to 115 PSI PEEK TM Thermoplastics No suffix is required when ordering products with the standard Fluorocarbon seals. When specifying an optional seal, refer to the following chart to determine the appropriate suffix.** oupling Series Ethylene Neoprene Perfluoro- Propylene elastomer PF Series E5 E12 E47 *To select proper seal materials, see Fluid ompatibility hart in ppendices section, or contact your Parker Quick oupling istributor. **N/ = Not vailable; ST = Standard (No Suffix Needed) Spectrum Series are available with these materials ody Material cetal/ss PVF/SS PVF/PEEK Seal Material Nitrile Fluorocarbon Fluorocarbon -3

110 Thermoplastic ouplings Push-To-onnect Spectrum Series pplications Parker s Spectrum Series couplers are the most advanced engineered thermoplastic couplings available. Spectrum Series couplings combine compact size, high flow capability, and light weight design to meet a broad range of coupling applications. Three material combinations allow the couplings to be used in markets as diverse as chemical processing, automation equipment, semi-conductor and food processing. Spectrum Series can be used in many applications previously reserved for stainless steel couplings. Thermoplastics Features Excellent hemical ompatibility Three Material ombinations: cetal/ss, PVF/SS and PVF/PEEK High Flow apacity Easy Push-To-onnect Operation vailable Valved and Unvalved Flexible Modular esign Four Point 360 Locking Mechanism Temperatures Up To 250 F Panel Mounting Option Performance Pressure rop in PSI Spectrum Series (1/8") Test Fluid: Water ouble Shut Off Flow in USGPM Specifications Single Shut Off Straight Through Pressure rop in PSI Spectrum Series (3/8") Test Fluid: Water ouble Shut Off Flow in USGPM Single Shut Off Straight Through How To Order S 2 - V FP FP - Female pipe MP - Male pipe H - Standard hose barb H - ulkhead hose barb Port Size 16 ths V - Valved S - Straight thru - oupler N - Nipple P - Panel mount coupler - cetal P - PVF K - PVF/PEEK ody Size 2-1/8 Inch 6-3/8 Inch Spectrum Series Thermoplastic ouplings cetal/ss PVF/SS PVF/PEEK (black with grey sleeve) (translucent with green sleeve) (translucent) ody Size 1/8 3/8 1/8 3/8 3/8 Pressure Range psi psi psi psi psi (0-10 bar) (0-10 bar) (0-8 bar) (0-8 bar) (1-8 bar) Temperature Range 0 F to 180 F 0 F to 180 F 0 F to 250 F 0 F to 250 F 0 F to 250 F (-20 to +80 ) (-20 to +80 ) (-20 to +120 ) (-20 to +120 ) (-20 to +120 ) Rated Flow 1.5 GPM 4.5 GPM 1.5 GPM 4.5 GPM 4.5 GPM (5.6 lpm) (17 lpm) (5.6 lpm) (17 lpm) (17 lpm) ody Material cetal cetal PVF PVF PVF Spring Material 316 SS 316 SS 316 SS 316 SS PEEK Seal Material Nitrile Nitrile Fluorocarbon Fluorocarbon Fluorocarbon -4

111 Thermoplastic ouplings Push-To-onnect Spectrum Series ouplers Female Pipe ody cetal* PVF* PVF/PEEK * Port Overall Hex Largest Size (in.) Part No. Part No. Part No. NPT Length Size iameter 1/8 S2-V-02-FP S2-PV-02-FP 1/ /8 S2-V-04-FP S2-PV-04-FP 1/ /8 S6-V-04-FP S6-PV-04-FP S6-KV-04-FP 1/ /8 S6-V-06-FP S6-PV-06-FP S6-KV-06-FP 3/ /8 S6-V-08-FP S6-PV-08-FP S6-KV-08-FP 1/ Male Pipe ody cetal* PVF* PVF/PEEK * Port Overall Hex Largest Size (in.) Part No. Part No. Part No. NPT Length Size iameter 1/8 S2-V-02-MP S2-PV-02-MP 1/ /8 S2-V-04-MP S2-PV-04-MP 1/ /8 S6-V-04-MP S6-PV-04-MP S6-KV-04-MP 1/ /8 S6-V-06-MP S6-PV-06-MP S6-KV-06-MP 3/ /8 S6-V-08-MP S6-PV-08-MP S6-KV-08-MP 1/ Thermoplastics Hose arb ody cetal* PVF* PVF/PEEK * Hose Overall Hex Largest Size (in.) Part No. Part No. Part No. I.. Length Size iameter 1/8 S2-V-03-H S2-PV-03-H 3/ (4 mm) 1/8 S2-V-04-H S2-PV-04-H 1/ (6 mm) 3/8 S6-V-04-H S6-PV-04-H S6-KV-04-H 1/ (6 mm) 3/8 S6-V-06-H S6-PV-06-H S6-KV-06-H 3/ (9 mm) 3/8 S6-V-08-H S6-PV-08-H S6-KV-08-H 1/ (13 mm) ulkhead Hose arb ody cetal* PVF* PVF/PEEK Hose Overall Hex Largest ulkhead Size (in.) Part No. Part No. Part No. I.. Length Size iameter Hex 1/8 S2-V-03-H S2-PV-03-H 3/ (4 mm) 1/8 S2-V-04-H S2-PV-04-H 1/ (6 mm) Panel Mount ouplers Female Pipe ody cetal* PVF* PVF/PEEK Hose Overall Hex Largest ulkhead Size (in.) Part No. Part No. Part No. I.. Length Size iameter Hex 1/8 S2-PV-02-FP S2-PPV-02-FP 1/ /8 S2-PV-04-FP S2-PPV-04-FP 1/ Hose arb ody cetal* PVF* PVF/PEEK Hose Overall Hex Largest ulkhead Size (in.) Part No. Part No. Part No. I.. Length Size iameter Hex 1/8 S2-PV-03-H S2-PPV-03-H 3/ (4 mm) 1/8 S2-PV-04-H S2-PPV-04-H 1/ (6 mm) * NOTE: To Order Unvalved oupler replace V with an S. -5

112 Thermoplastic ouplings Push-To-onnect Spectrum Series Nipples Unvalved Female Pipe ody cetal PVF PVF/PEEK Port Overall Hex Largest Size (in.) Part No. Part No. Part No. NPT Length Size iameter 1/8 S2-NS-02-FP S2-PNS-02-FP 1/ /8 S2-NS-04-FP S2-PNS-04-FP 1/ /8 S6-NS-04-FP S6-PNS-04-FP 1/ /8 S6-NS-06-FP S6-PNS-06-FP 3/ /8 S6-NS-08-FP S6-PNS-08-FP 1/ Thermoplastics Male Pipe ody cetal PVF PVF/PEEK Port Overall Hex Largest Size (in.) Part No. Part No. Part No. NPT Length Size iameter 1/8 S2-NS-02-MP S2-PNS-02-MP 1/ /8 S2-NS-04-MP S2-PNS-04-MP 1/ /8 S6-NS-04-MP S6-PNS-04-MP 1/ /8 S6-NS-06-MP S6-PNS-06-MP 3/ /8 S6-NS-08-MP S6-PNS-08-MP 1/ Hose arb ody cetal PVF PVF/PEEK Hose Overall Largest Size (in.) Part No. Part No. Part No. I.. Length iameter 1/8 S2-NS-03-H S2-PNS-03-H 3/ (4 mm) 1/8 S2-NS-04-H S2-PNS-04-H 1/ (6 mm) 3/8 S6-NS-04-H S6-PNS-04-H 1/ (6 mm) 3/8 S6-NS-06-H S6-PNS-06-H 3/ (9 mm) 3/8 S6-NS-08-H S6-PNS-08-H 1/ (13 mm) ulkhead Hose arb ody cetal PVF PVF/PEEK Hose Overall Hex Largest ulkhead Size (in.) Part No. Part No. Part No. I.. Length Size iameter Hex 1/8 S2-NS-03-H S2-PNS-03-H 3/ (4 mm) 1/8 S2-NS-04-H S2-PNS-04-H 1/ (6 mm) -6

113 Thermoplastic ouplings Push-To-onnect Spectrum Series Nipples Valved Female Pipe ody cetal PVF PVF/PEEK Port Overall Hex Largest Size (in.) Part No. Part No. Part No. NPT Length Size iameter 1/8 S2-NV-02-FP S2-PNV-02-FP 1/ /8 S2-NV-04-FP S2-PNV-04-FP 1/ /8 S6-NV-04-FP S6-PNV-04-FP S6-KNV-04-FP 1/ /8 S6-NV-06-FP S6-PNV-06-FP S6-KNV-06-FP 3/ /8 S6-NV-08-FP S6-PNV-08-FP S6-KNV-08-FP 1/ Male Pipe ody cetal PVF PVF/PEEK Port Overall Hex Largest Size (in.) Part No. Part No. Part No. NPT Length Size iameter 1/8 S2-NV-02-MP S2-PNV-02-MP 1/ /8 S2-NV-04-MP S2-PNV-04-MP 1/ /8 S6-NV-04-MP S6-PNV-04-MP S6-KNV-04-MP 1/ /8 S6-NV-06-MP S6-PNV-06-MP S6-KNV-06-MP 3/ /8 S6-NV-08-MP S6-PNV-08-MP S6-KNV-08-MP 1/ Thermoplastics Hose arb ody cetal PVF PVF/PEEK Hose Overall Hex Largest Size (in.) Part No. Part No. Part No. I.. Length Size iameter 1/8 S2-NV-03-H S2-PNV-03-H 3/ (4 mm) 1/8 S2-NV-04-H S2-PNV-04-H 1/ (6 mm) 3/8 S6-NV-04-H S6-PNV-04-H S6-KNV-04-H 1/ (6 mm) 3/8 S6-NV-06-H S6-PNV-06-H S6-KNV-06-H 3/ (9 mm) 3/8 S6-NV-08-H S6-PNV-08-H S6-KNV-08-H 1/ (13 mm) ulkhead Hose arb ody cetal PVF PVF/PEEK Hose Overall Hex Largest ulkhead Size (in.) Part No. Part No. Part No. I.. Length Size iameter Hex 1/8 S2-NV-03-H S2-PNV-03-H 3/ (4 mm) 1/8 S2-NV-04-H S2-PNV-04-H 1/ (6 mm) -7

114 Thermoplastic ouplings Non-Spill ouplings PF Series hemical Transfer ouplings Thermoplastics pplications hemical ispensing Systems Spray pplication Equipment Mini ulk Tanks Replacement for anjo Style amlok Fittings & all Valves ulk Transfer arrels Features The Parker PF Series ry isconnect couplings virtually eliminate fluid loss upon disconnection and are designed to help meet the demand for closed system transfer and dispensing of chemicals and fluids with minimal environmental contamination. They can be used with concentrated or diluted industrial chemicals, fertilizers, herbicides, insecticides, fungicides or pesticides when transferring from bulk storage tanks, returnable containers, applicators, etc. The PF Series 2" body size is ideal for large bulk transfer of fluids and eliminating fluid spillage when connecting and disconnecting. dditional features include: Rugged Glass filled Polypropylene construction for chemical compatibility and reduced cost. Push-to-connect design. Flush face valves exhibit minimal spillage upon connect or disconnect and air inclusion on connect, and enables ease of cleaning. PTFE coated Fluorocarbon tank gasket for improved chemical compatiblity. 1" coupler has non-wetted springs. Specifications Performance ody Size 1/2" 1" 2 Materials: ody Polypropylene Springs 316 Stainless Steel Seals Fluorocarbon (1) Rated Pressure (at 68 F) 100 PSI 60 PSI 100 PSI Rated Flow 12 GPM 20 GPM 50 GPM Pressure rop 11.3 PSI 3.4 PSI 4 PSI at Rated Flow Force to onnect 32 lbs. 54 lbs. 41 lbs. Force to isconnect 12 lbs. 17 lbs. 17 lbs. Operating Temp. +40 F to +140 F Storage Temp. -20 F to +140 F Maximum Spillage 0.14 ml 1ml 9 ml per isconnect.01 cu. in..06 cu. in. (1cc).5 cu. in. Vacuum Rating 27.4 Hg ontact Factory ontact Factory1 (1) lso available in EPM, Nitrile, Neoprene, Perfluoroelastomer Pressure rop in PSI /2" PF (1/2", 1", 2") Test Fluid: Water 1" Flow in USGPM 2" -8

115 Thermoplastic ouplings Non-Spill ouplings PF Series Non-Spill hemical Transfer ouplings ouplers 1" NPT ody Part Port* Overall Largest Wrench Wt. (L.) Size (in.) No. Thread Length iameter Flats P/Piece 1/2 PF-501-8FP 1/2"NPT PF FP 1" NPT PF FP 2 NPT * Female NPT Threads standard. For other port options contact the division. Nipples 1" NPT ody Tank Overall Largest Wrench Wt. (L.) Size Part Port* Mount Length iameter Flats P/Piece (in.) No. Thread Thread 1/2 PF-502-8FP 1/2" NPT None PF FP 1" NPT None PF FP 2 NPT None * Female NPT Threads standard. For other port options contact the division. Thermoplastics Nipples - Tank Mount Fluorocarbon Gasket 2 1/2-5 Modified 5 /45 uttress Thread 1" NPT /2 NPS Modified Thread ody Tank Overall Largest WrenchWt. (L.) Size Part Port* Mount Length iameter Flats P/Piece (in.) No. Thread Thread 1 PF M 1" NPT Modified uttress 1 PF MP 1" NPT Modified NPS * Female NPT Threads standard. For other port options contact the division. Fluorocarbon Gasket 1" NPT ust aps and Plugs oupler ust ap FR-501 ody oupler ust ap Nipple ust ap Material Size (in.) Part No. Part No. 1/2 FR-501 FR-502 Synthetic Rubber 1 None PFR-1002 Ethylene Propylene 1 None PFR-1002-NS* Ethylene Propylene * For use with Tank Mount Nipples Nipple ust ap FR-502 Nipple ust ap PFR-1002 Nipple ust ap (Tank Mount) PFR-1002-NS -9

116 Thermoplastic ouplings Ordering Information Thermoplastics When ordering Parker coupler bodies and nipples, please state the part number of each type of coupler body and each type of nipple desired. List coupler bodies and nipples as separate items rather than in combinations. e sure to double check thread or hose sizes of items required. Many of Parker s coupling products are available with unique non-standard options well suited to very specific applications. Examples of unusual end use applications might include: high temperatures (above 250 F), extremely caustic/corrosive solutions passing through the coupling, external/environmental corrosion situations, or other high wear and tear situations such as dragging the product along the ground. Please see the Fluid ompatibility hart at the end of the catalog for a guide in selecting material for various media. It is always recommended that the be contacted with any questions concerning specific product application needs. Please Note: ertain couplings series have additional "Special Order Information" which should be referred to in ordering those products. If applicable to the product, "Special Order Information" is found next to the Features and Specifications charts. Optional Seals Suffix* No suffix is required when ordering products with the standard Fluorocarbon seals. When specifying an optional seal, refer to the following chart to determine the appropriate suffix.** Ethylene Perfluoro- oupling Series Propylene Neoprene elastomer PF Series E5 E12 * To select proper seal materials, see Fluid ompatibility hart in ppendices section, or contact your Parker Quick oupling istributor. ** N/ = Not vailable; ST = Standard (No Suffix Needed) *** Parofluor **** upont Kalrez Spectrum Series are available with these materials ody Material cetal/ss PVF/SS PVF/PEEK Seal Material Nitrile Fluorocarbon Fluorocarbon E35*** E47**** -10

117 Swivels Swivels -1

118 Swivels General Introduction pplications Some common markets and applications for swivels are: Injection Molding ar Washes Pulp and Paper Hose Reels Logging Pressure Washers Refuse Trucks Machine Tools Utility Equipment Steel Mills Mobile Equipment Palletizers Flight Simulators nd many more -2

119 Swivels Table of ontents pplications...-1 PS Series Introduction...-4 How To Order...-5 In-Line Repair Kits Seal Options S Series Introduction How To Order Repair Kits Seal Options Swivels -3

120 Swivels Introduction PS Series Swivels Introduction The design and manufacturing processes vital to a swivel s quality are the cornerstone of the Quick oupling ivision s day to day operations. The PS Series Swivel is designed to meet the application needs and performance requirements of the market. Pressure capabilities up to 5000 psi, 1/4" through 2" body sizes, a variety of port options, hromium-6 Free or nickel plating and a wide range of seal options make the PS Series Swivels ideal for an array of dynamic applications. Specifications Features Hardened bearing races for extended service life. Full flow design minimizes pressure drop for optimum system performance. Sealed bearing design isolates bearing race from media and environment. Reduced bearing load design minimizes wear in the bearing race and extends service life. PTFE back-up rings support primary seal for high-pressure applications. hromium-6 Free plating for maximum corrosion resistance. Variety of seal options available. Three piece swivel design for sizes 1 1/4" through 2" for superior performance and service life. Precision needle bearings and ball bearings sized 1 1/4" through 2" for additional side load resistance. Polyurethane U-up primary seal standard for sizes 1 1/4" through 2". PS Series Swivels eliminate hose twist and torque that may cause premature hose failure. ody Size (in.) 1/4 3/8 1/2 3/ /4 1-1/2 2 Maximum Rated Pressure (PSI) Except the following port options in the noted size 03 (Male JI 37 ) (Male SE O-Ring oss) (Female JI 37 ) 90 Housing Port (Female JI 37 ) In-Line Housing Port (Female NPSM) Temperature Range (std seals) -40 to 250 F -30 to 180 F Performance ata RPM Recommended Max. Speed vs. Pressure /4" 25 3/8" 1/2" 20 3/4" 15 1" 10 2" 5 1-1/2" Pressure (PSI) Torque (in-lbs) Torque vs. Pressure " 3/4" /2" 10 3/8" 5 1/4" Pressure (PSI) Pressure rop (psid) /4" 3/8" 90 PS Swivel 150 SUS Oil Flow vs. Pressure rop 1/2" 3/4" Flow (USGPM) 1" -4

121 Swivels How To Order PS Series In-Line Swivels 90 Swivels Shaft Housing Shaft Housing PS Part Number: PS Y - Seal ode: lank = Nitrile = flas * W = Ethylene Propylene Y = Fluorocarbon Z = Neoprene For Perfluoroelastomer Seal Option ontact the ivision. Housing Port Size (1/16 of an inch) Material and Finish: lank = arbon Steel w/hromium-6 Free Plating (Std.) NI = arbon Steel with Electroless Nickel Plating* S3 = 303 Stainless Steel Passivated* S6 = 316 Stainless Steel Electropolished* Swivels Shaft Port Size (1/16 of an inch) onfiguration: 1 = In-line 9 = 90 degree ody Size (1/16 of an inch) Shaft Port onfiguration: 01 = Male NPTF 02 = Female NPTF 03 = Male JI 37 egree 05 = Male SE O-Ring Straight Thread 10 = Female SE Straight Thread Housing Port onfiguration: 01 = Male NPTF(Non-Standard)* 02 = Female NPTF 03 = Male JI 37 egree 05 = Male SE O-Ring Straight Thread 06 = Female JI 37 egree 07 = Female NPSM Pipe Swivel 10 = Female SE Straight Thread Parker Swivel designator *ontact ivision for price and delivery On -24 and -32 sizes, Polyurethane U-up Seal is standard. For -20 Ports, -24 ody is used. -5

122 Swivels In-Line PS Series Materials Of onstruction Housing*:...arbon Steel Shaft*:...arbon Steel Plating:*...hromium-6 Free earing:*...hrome O-Rings:*...Nitrile ack-up Ring:...PTFE * See How-To-Order for optional material, plating, and seals. Housing O-Ring ack-up Ring ap Screw earing O-Ring Shaft Swivels Male Pipe - Female Pipe Hex 1 Port 1 Hex 2 Port 2 Part Number Hex 1 Hex 2 Port 1 Port 2 PS /4-18 1/ mm 40.6 mm 19.0 mm 30.2 mm NPTF NPTF PS /8-18 3/ mm 41.7 mm 22.2 mm 33.3 mm NPTF NPTF PS /2-14 1/ mm 45.5 mm 28.6 mm 36.5 mm NPTF NPTF PS /4-14 3/ mm 47.0 mm 35.0 mm 42.9 mm NPTF NPTF PS / / mm 53.5 mm 41.3 mm 47.6 mm NPTF NPTF Male Pipe - Male 37 Flare Hex 1 Port 1 Hex 2 Port 2 Part Number Hex 1 Hex 2 Port 1 Port 2 PS /4-18 7/ mm 47.5 mm 19.0 mm 30.2 mm NPTF UNF PS /8-18 9/ mm 48.3 mm mm NPTF UNF PS /2-14 3/ mm 53.1 mm 28.6 mm 36.5 mm NPTF UNF PS / / mm 58.4 mm 35.0 mm 42.9 mm NPTF UN PS /2 1-5/ mm 62.2 mm 41.3 mm 47.6 mm NPTF UN Male Pipe - Female 37 Flare Hex 1 Port 1 Hex 2 Port 2 Part Number Hex 1 Hex 2 Port 1 Port 2 PS /4-18 7/ mm 43.9 mm 19.0 mm 30.2 mm NPTF UNF PS /8-18 9/ mm 44.5 mm 22.2 mm 33.3 mm NPTF UNF PS /2-14 3/ mm 46.0 mm 28.6 mm 36.5 mm NPTF UNF PS / / mm 51.3 mm 35.0 mm 42.9 mm NPTF UN PS /2 1-5/ mm 55.6 mm 41.3 mm 47.6 mm NPTF UN -6

123 Swivels In-Line PS Series Male Pipe - Female SE Straight Thread Part Number Hex 1 Hex 2 Port 1 Port 2 Hex 1 Port 1 Hex 2 Port 2 PS /4-18 7/ mm 43.7 mm 19.0 mm 30.2 mm NPTF UNF PS /8-18 9/ mm 43.7 mm 22.2 mm 33.3 mm NPTF UNF PS /2-14 3/ mm 45.5 mm 28.6 mm 36.5 mm NPTF UNF PS / / mm 52.8 mm 35.0 mm 42.9 mm NPTF UN PS /2 1-5/ mm 55.9 mm 41.3 mm 47.6 mm NPTF UN Female Pipe - Female Pipe Part Number Hex 1 Hex 2 Port 1 Port 2 Hex 1 Port 1 3 Piece esign Port 1 Hex 2 Port 2 Port 2 ia PS /4-18 1/ mm 40.6 mm 19.0 mm 30.2 mm NPTF NPTF PS /8-18 3/ mm 41.7 mm 22.2 mm 33.3 mm NPTF NPTF PS /2-14 1/ mm 45.5 mm 28.6 mm 36.5 mm NPTF NPTF PS /4-14 3/ mm 47.0 mm 35.0 mm 42.9 mm NPTF NPTF PS / / mm 53.5 mm 41.3 mm 47.6 mm NPTF NPTF Part Number Wrench Flats ia. Port 1 Port 2 PS " 3.38" 2.63" 2.88" 1 1/4-11 1/2 1 1/4-11 1/ mm 85.9 mm 66.7 mm 73.0 mm NPTF NPTF PS " 3.38" 2.63" 2.88" 1 1/2-11 1/2 1 1/2-11 1/ mm 85.9 mm 66.7 mm 73.0 mm NPTF NPTF PS " 3.58" 3.06" 3.35" / / mm 90.8 mm 77.6 mm 85.1 mm NPTF NPTF Swivels Wrench Flats Female Pipe - Male 37 Flare Hex 1 Port 1 3 Piece esign Hex 2 Port 2 Part Number Hex 1 Hex 2 Port 1 Port 2 PS /4-18 7/ mm 47.5 mm 19.0 mm 30.2 mm NPTF UNF PS /8-18 9/ mm 48.3 mm 22.2 mm 33.3 mm NPTF UNF PS /2-14 3/ mm 53.1 mm 28.6 mm 36.5 mm NPTF UNF PS / / mm 58.4 mm 35.0 mm 42.9 mm NPTF UN PS /2 1-5/ mm 62.2 mm 41.3 mm 47.6 mm NPTF UN Port 2 Part Number Wrench Flats ia. Port 1 Port 2 Port 1 ia PS " 3.78" 2.63" 2.88" 1 1/4-11 1/2 1 5/ mm 95.9 mm 66.7 mm 73.0 mm NPTF UN PS " 3.78" 2.63" 2.88" 1 1/2-11 1/2 1 7/ mm 95.9 mm 66.7 mm 73.0 mm NPTF UN PS " 4.28" 3.06" 3.35" /2 2 1/ mm mm 77.6 mm 85.1 mm NPTF UN Wrench Flats -7

124 Swivels In-Line PS Series Female Pipe - Female 37 Flare Hex 1 Port 1 Hex 2 Port 2 Part Number Hex 1 Hex 2 Port 1 Port 2 PS /4-18 7/ mm 43.9 mm 19.0 mm 30.2 mm NPTF UNF PS /8-18 9/ mm 44.5 mm 22.2 mm 33.3 mm NPTF UNF PS /2-14 3/ mm 46.0 mm 28.6 mm 36.5 mm NPTF UNF PS / / mm 51.3 mm 35.0 mm 42.9 mm NPTF UN PS /2 1-5/ mm 55.6 mm 41.3 mm 47.6 mm NPTF UN Female Pipe - Female SE Straight Thread Swivels Hex 1 Port 1 Male 37 Flare - Female Pipe Hex 2 Port 2 Part Number Hex 1 Hex 2 Port 1 Port 2 PS /4-18 7/ mm 43.7 mm 19.0 mm 30.2 mm NPTF UNF PS /8-18 9/ mm 43.7 mm 22.2 mm 33.3 mm NPTF UNF PS /2-14 3/ mm 45.5 mm 28.6 mm 36.5 mm NPTF UNF PS / / mm 52.8 mm 35.0 mm 42.9 mm NPTF UN PS /2 1-5/ mm 55.9 mm 41.3 mm 47.6 mm NPTF UN Hex 1 Port 1 3 Piece esign Port 1 Hex 2 Port 2 Port 2 Part Number Hex 1 Hex 2 Port 1 Port 2 PS / / mm 40.6 mm 19.0 mm 30.2 mm UNF NPTF PS / / mm 41.7 mm 22.2 mm 33.3 mm UNF NPTF PS /4-16 1/ mm 45.5 mm 28.6 mm 36.5 mm UNF NPTF PS / / mm 47.0 mm 35.0 mm 42.9 mm UN NPTF PS / / mm 53.5 mm 41.3 mm 47.6 mm UN NPTF Part Number Wrench Flats ia. Port 1 Port 2 PS " 3.38" 2.63" 2.88" 1 5/ /4-11 1/ mm 85.9 mm 66.7 mm 73.0 mm UN NPTF ia PS " 3.38" 2.63" 2.88" 1 7/ /2-11 1/ mm 85.9 mm 66.7 mm 73.0 mm UN NPTF PS " 3.58" 3.06" 3.35" 2 1/ / mm 90.8 mm 77.6 mm 85.1 mm UN NPTF Wrench Flats -8

125 Swivels In-Line PS Series Male 37 Flare - Male 37 Flare Part Number Hex 1 Hex 2 Port 1 Port 2 Hex 1 Port 1 3 Piece esign Hex 2 Port 2 PS / / mm 47.5 mm 19.0 mm 30.2 mm UNF UNF PS / / mm 48.3 mm 22.2 mm 33.3 mm UNF UNF PS /4-16 3/ mm 53.1 mm 28.6 mm 36.5 mm UNF UNF PS /8-14 7/ mm 55.6 mm 28.6 mm 36.5 mm UNF UNF PS / / mm 58.4 mm 35.0 mm 42.9 mm UN UN PS / / mm 62.2 mm 41.3 mm 47.6 mm UN UN Port 1 Port 2 ia Part Number Wrench Flats ia. Port 1 Port 2 PS " 3.78" 2.63" 2.88" 1 5/ / mm 95.9 mm 66.7 mm 73.0 mm UN UN PS " 3.78" 2.63" 2.88" 1 7/ / mm 95.9 mm 66.7 mm 73.0 mm UN UN PS " 4.28" 3.06" 3.35" 2 1/ / mm mm 77.6 mm 85.1 mm UN UN Wrench Flats Male 37 Flare - Female 37 Flare Hex 1 Hex 2 Port 1 Port 2 Part Number Hex 1 Hex 2 Port 1 Port 2 PS / / mm 43.9 mm 19.0 mm 30.2 mm UNF UNF PS / / mm 44.5 mm 22.2 mm 33.3 mm UNF UNF PS /4-16 3/ mm 46.0 mm 28.6 mm 36.5 mm UNF UNF PS / / mm 51.3 mm 35.0 mm 42.9 mm UN UN PS / / mm 55.6 mm 41.3 mm 47.6 mm UN UN Swivels Male 37 Flare - Female SE Straight Thread Part Number Hex 1 Hex 2 Port 1 Port 2 Hex 1 Port 1 3 Piece esign Port 1 Hex 2 Port 2 Port 2 PS / / mm 43.7 mm 19.0 mm 30.2 mm UNF UNF PS / / mm 43.7 mm 22.2 mm 33.3 mm UNF UNF PS /4-16 3/ mm 45.5 mm 28.6 mm 36.5 mm UNF UNF PS / / mm 52.8 mm 35.0 mm 42.9 mm UN UN PS / / mm 55.9 mm 41.3 mm 47.6 mm UN UN Part Number ia. Wrench Flats Port 1 Port 2 ia PS " 4.63" 3.43" 1.27" 2.63" 3.36" 1 5/ / mm mm 87.0 mm 32.3 mm 66.7 mm 85.2 mm UN UN PS " 4.63" 3.43" 1.27" 2.63" 3.36" 17/ / mm mm 87.0 mm 32.3 mm 66.7 mm 85.2 mm UN UN PS " 5.45" 3.93" 1.52" 3.06" 4.19" 2 1/ / mm mm 99.7 mm 38.5 mm 77.6 mm mm UN UN Wrench Flats -9

126 Swivels In-Line PS Series Male SE O-Ring Straight Thread - Female Pipe Part Number Hex 1 Hex 2 Port 1 Port 2 Hex 1 Port 1 Hex 2 Port 2 PS / / mm 40.6 mm 19.0 mm 30.2 mm UNF NPTF PS / / mm 41.7 mm 22.2 mm 33.3 mm UNF NPTF PS /4-16 1/ mm 45.5 mm 28.6 mm 36.5 mm UNF NPTF PS / / mm 47.0 mm 35.0 mm 42.9 mm UN NPTF PS / / mm 53.5 mm 41.3 mm 47.6 mm UN NPTF Male SE O-Ring Straight Thread - Male 37 Flare Part Number Hex 1 Hex 2 Port 1 Port 2 Swivels Hex 1 Port 1 Hex 2 Port 2 PS / / mm 47.5 mm 19.0 mm 30.2 mm UNF UNF PS / / mm 48.3 mm 22.2 mm 33.3 mm UNF UNF PS /4-16 3/ mm 53.1 mm 28.6 mm 36.5 mm UNF UNF PS /8-14 7/ mm 55.6 mm 28.6 mm 36.5 mm UNF UNF PS / / mm 58.4 mm 35.0 mm 42.9 mm UN UN PS / / mm 62.2 mm 41.3 mm 47.6 mm UN UN Male SE O-Ring Straight Thread - Female 37 Flare Hex 1 Port 1 Hex 2 Port 2 Part Number Hex 1 Hex 2 Port 1 Port 2 PS / / mm 43.9 mm 19.0 mm 30.2 mm UNF UNF PS / / mm 44.5 mm 22.2 mm 33.3 mm UNF UNF PS /4-16 3/ mm 46.0 mm 28.6 mm 36.5 mm UNF UNF PS / / mm 51.3 mm 35.0 mm 42.9 mm UN UN PS / / mm 55.6 mm 41.3 mm 47.6 mm UN UN Male SE O-Ring Straight Thread - Female SE Straight Thread Part Number Hex 1 Hex 2 Port 1 Port 2 Hex 1 Port 1 Hex 2 Port 2 PS / / mm 43.7 mm 19.0 mm 30.2 mm UNF UNF PS / / mm 43.7 mm 22.2 mm 33.3 mm UNF UNF PS /4-16 3/ mm 45.5 mm 28.6 mm 36.5 mm UNF UNF PS / / mm 52.8 mm 35.0 mm 42.9 mm UN UN PS / / mm 55.9 mm 41.3 mm 47.6 mm UN UN -10

127 Swivels In-Line PS Series Female SE Straight Thread - Female Pipe Part Number Hex 1 Hex 2 Port 1 Port 2 Hex 1 Port 1 Hex 2 Port 2 PS / / mm 40.6 mm 19.0 mm 30.2 mm UNF NPTF PS / / mm 41.7 mm 22.2 mm 33.3 mm UNF NPTF PS /4-16 1/ mm 45.5 mm 28.6 mm 36.5 mm UNF NPTF PS / / mm 47.0 mm 35.0 mm 42.9 mm UN NPTF PS / / mm 53.5 mm 41.3 mm 47.6 mm UN NPTF Female SE Straight Thread - Male 37 Flare Hex 1 Port 1 Hex 2 Port 2 Female SE Straight Thread - Female 37 Flare Part Number Hex 1 Hex 2 Port 1 Port 2 PS / / mm 47.5 mm 19.0 mm 30.2 mm UNF UNF PS / / mm 48.3 mm 22.2 mm 33.3 mm UNF UNF PS /4-16 3/ mm 53.1 mm 28.6 mm 36.5 mm UNF UNF PS / / mm 58.4 mm 35.0 mm 42.9 mm UN UN PS / / mm 62.2 mm 41.3 mm 47.6 mm UN UN Swivels Part Number Hex 1 Hex 2 Port 1 Port 2 Hex 1 Port 1 Hex 2 Port 2 PS / / mm 43.9 mm 19.0 mm 30.2 mm UNF UNF PS / / mm 44.5 mm 22.2 mm 33.3 mm UNF UNF PS /4-16 3/ mm 46.0 mm 28.6 mm 36.5 mm UNF UNF PS / / mm 51.3 mm 35.0 mm 42.9 mm UN UN PS / / mm 55.6 mm 41.3 mm 47.6 mm UN UN Female SE Straight Thread - Female SE Straight Thread Part Number Hex 1 Hex 2 Port 1 Port 2 Hex 1 Port 1 3 Piece esign Hex 2 Port 2 PS / / mm 43.7 mm 19.0 mm 30.2 mm UNF UNF PS / / mm 43.7 mm 22.2 mm 33.3 mm UNF UNF PS /4-16 3/ mm 45.5 mm 28.6 mm 36.5 mm UNF UNF PS / / mm 52.8 mm 35.0 mm 42.9 mm UN UN PS / / mm 55.9 mm 41.3 mm 47.6 mm UN UN Port 2 Part Number Wrench Flats ia. Port 1 Port 2 Port 1 ia PS " 4.63" 3.43" 1.27" 2.63" 3.36" 1 5/ / mm mm 87.0 mm 32.3 mm 66.7 mm 85.2 mm UN UN PS " 4.63" 3.43" 1.27" 2.63" 3.36" 1 7/ / mm mm 87.0 mm 32.3 mm 66.7 mm 85.2 mm UN UN PS " 5.45" 3.93" 1.52" 3.06" 4.19" 2 1/ / mm mm 99.7 mm 38.5 mm 77.6 mm mm UN UN Wrench Flats -11

128 Swivels 90 PS Series Port 2 Hex 1 Hex 2 Port 1 O-Ring Materials Of onstruction Housing*:...arbon Steel Shaft*:...arbon Steel Plating*:...hromium-6 Free earing*:...hrome O-Rings*:...Nitrile ack-up Ring:...PTFE * See How-To-Order for optional material plating and seals. Housing O-Ring ack-up Ring ap Screw earing O-Ring Shaft Swivels Male Pipe - Female Pipe Port 1 Hex 1 Port 2 I Part Number ia. Hex 1 Port 1 Port 2 PS /4-18 1/ mm 62.0 mm 30.5 mm 19.0 mm NPTF NPTF PS /8-18 3/ mm 64.4 mm 32.8 mm 22.2 mm NPTF NPTF PS /2-14 1/ mm 72.0 mm 37.8 mm 28.6 mm NPTF NPTF PS /4-14 3/ mm 76.1 mm 44.6 mm 35.0 mm NPTF NPTF PS / / mm 90.0 mm 54.9 mm 41.3 mm NPTF NPTF Male Pipe - Male 37 Flare Hex 1 Port 1 Hex 2 Port 2 I Part Number ia Hex 1 Hex 2 Port 1 Port 2 PS /4-18 7/ mm 62.0 mm 35.2 mm 50.5 mm 30.5 mm 19.0 mm 14.3 mm NPTF UNF PS /8-18 9/ mm 64.4 mm 36.6 mm 53.0 mm 32.8 mm 22.2 mm 17.5 mm NPTF UNF PS /2-14 3/ mm 72.0 mm 45.1 mm 67.1 mm 44.0 mm 28.6 mm 22.2 mm NPTF UNF PS / / mm 76.1 mm 56.9 mm 85.3 mm 55.2 mm 35.0 mm 31.8 mm NPTF UN PS /2 1-5/ mm 90.0 mm 61.3 mm 92.9 mm 63.0 mm 41.3 mm 38.1 mm NPTF UN -12

129 Swivels 90 PS Series Male Pipe - Male SE O-Ring Straight Thread Hex 1 Port 1 Hex 2 Port 2 I Part Number ia. Hex 1 Hex 2 Port 1 Port 2 PS /4-18 7/ mm 62.0 mm 35.0 mm 50.2 mm 30.5 mm 19.0 mm 14.3 mm NPTF UNF PS /8-18 9/ mm 64.4 mm 39.4 mm 55.8 mm 32.8 mm 22.2 mm 17.5 mm NPTF UNF PS /2-14 3/ mm 72.0 mm 47.2 mm 69.2 mm 44.0 mm 28.6 mm 22.2 mm NPTF UNF PS / / mm 76.1 mm 61.0 mm 88.5 mm 55.2 mm 35.0 mm 31.8 mm NPTF UN PS /2 1-5/ mm 90.0 mm 63.4 mm 94.9 mm 63.0 mm 41.3 mm 38.1 mm NPTF UN Male Pipe - Female 37 Flare Hex 1 Port 1 Hex 2 Port 2 I Part Number ia. Hex 1 Hex 2 Port 1 Port 2 PS /4-18 7/ mm 62.0 mm 37.3 mm 52.5 mm 30.5 mm 19.0 mm 14.3 mm NPTF UNF PS /8-18 9/ mm 64.4 mm 39.9 mm 56.3 mm 32.8 mm 22.2 mm 17.5 mm NPTF UNF PS /2-14 3/ mm 72.0 mm 48.4 mm 70.4 mm 44.0 mm 28.6 mm 22.2 mm NPTF UNF PS / / mm 76.1 mm 59.4 mm 87.0 mm 55.2 mm 35.0 mm 31.8 mm NPTF UN PS /2 1-5/ mm 90.0 mm 64.6 mm 96.2 mm 63.0 mm 41.3 mm 38.1 mm NPTF UN Swivels Male Pipe - Female NPSM Pipe Swivel Part Number ia. Hex 1 Hex 2 Port 1 Port 2 Hex 1 Port 1 Hex 2 Port 2 I PS /4-18 1/ mm 62.0 mm 37.5 mm 52.8 mm 30.5 mm 19.0 mm 17.4 mm NPTF NPSM PS /8-18 3/ mm 64.4 mm 38.4 mm 54.8 mm 32.8 mm 22.2 mm 22.2 mm NPTF NPSM PS /2-14 1/ mm 72.0 mm 47.2 mm 69.2 mm 44.0 mm 28.6 mm 25.4 mm NPTF NPSM PS /4-14 3/ mm 76.1 mm 56.9 mm 84.5 mm 55.2 mm 35.0 mm 31.8 mm NPTF NPSM PS / / mm 90.0 mm 63.1 mm 94.6 mm 63.0 mm 41.3 mm 38.1 mm NPTF NPSM Male Pipe - Female SE Straight Thread Hex 1 Port 1 I Port 2 Part Number ia. Hex 1 Port 1 Port 2 PS /4-18 7/ mm 62.0 mm 30.5 mm 19.0 mm NPTF UNF PS /8-18 9/ mm 64.4 mm 32.8 mm 22.2 mm NPTF UNF PS /2-14 3/ mm 72.0 mm 44.0 mm 28.6 mm NPTF UNF PS / / mm 76.1 mm 55.2 mm 35.0 mm NPTF UN PS /2 1-5/ mm 90.0 mm 63.0 mm 41.3 mm NPTF UN -13

130 Swivels 90 PS Series Male Pipe - O-Ring Face Seal Part Number ia. Hex 1 Hex 2 Port 1 Port 2 Hex 1 Port 1 Hex 2 Port 2 I PS4901JM /4-18 9/ mm 62.0 mm 32.5 mm 47.9 mm 30.5 mm 19.0 mm 14.3 mm NPTF UNF PS6901JM / / mm 64.4 mm 35.6 mm 52.0 mm 32.8 mm 22.2 mm 17.5 mm NPTF UN PS8901JM / / mm 72.0 mm 44.1 mm 66.1 mm 44.0 mm 28.6 mm 22.2 mm NPTF UN PS12901JM / / mm 76.1 mm 55.4 mm 83.0 mm 55.2 mm 35.0 mm 31.8 mm NPTF UN PS16901JM /2 1-7/ mm 90.0 mm 59.6 mm 91.1 mm 63.0 mm 41.3 mm 38.1 mm NPTF UN Female Pipe - Female Pipe Part Number ia Hex 1 Port 1 Port 2 Swivels Hex 1 Port 1 3 Piece esign Port 1 Wrench Flats Port 2 I Port 2 ia PS /4-18 1/ mm 51.2 mm 30.5 mm 19.0 mm NPTF NPTF PS /8-18 3/ mm 55.2 mm 32.8 mm 22.2 mm NPTF NPTF PS /2-14 1/ mm 60.3 mm 37.8 mm 28.6 mm NPTF NPTF PS /4-14 3/ mm 70.4 mm 44.6 mm 35.0 mm NPTF NPTF PS / / mm 80.3 mm 54.9 mm 41.3 mm NPTF NPTF Part Number Wrench Flats ia. Port 1 Port 2 PS " 4.63" 3.43" 1.27" 2.63" 3.36" 1 1/4-11 1/2 1 1/4-11 1/ mm mm 87.0 mm 32.3 mm 66.7 mm 85.2 mm NPTF NPTF PS " 4.63" 3.43" 1.27" 2.63" 3.36" 1 1/2-11 1/2 1 1/2-11 1/ mm mm 87.0 mm 32.3 mm 66.7 mm 85.2 mm NPTF NPTF PS " 5.45" 3.93" 1.52" 3.06" 4.19" / / mm mm 99.7 mm 38.5 mm 77.6 mm mm NPTF NPTF Female Pipe - Male 37 Flare Hex 2 Hex 1 Port 1 3 Piece esign Port 2 I Part Number ia Hex 1 Hex 2 Port 1 Port 2 PS /4-18 7/ mm 51.2 mm 35.2 mm 50.5 mm 30.5 mm 19.0 mm 14.3 mm NPTF UNF PS /8-18 9/ mm 55.2 mm 36.6 mm 53.0 mm 32.8 mm 22.2 mm 17.5 mm NPTF UNF PS /2-14 3/ mm 60.3 mm 45.1 mm 67.1 mm 44.0 mm 28.6 mm 22.2 mm NPTF UNF PS / / mm 70.4 mm 56.9 mm 85.3 mm 55.2 mm 35.0 mm 31.8 mm NPTF UN PS /2 1-5/ mm 80.3 mm 61.3 mm 92.9 mm 63.0 mm 41.3 mm 38.1 mm NPTF UN Port 2 Hex Part Number E Hex Wrench Flats ia. Port 1 Port 2 Port 1 ia E PS " 4.63" 3.43" 2.85" 4.53" 1.88" 2.63" 3.36" 1 1/4-11 1/2 1 5/ mm mm 87.0 mm 72.4 mm mm 47.6 mm 66.7 mm 85.2 mm NPTF UN PS " 4.65" 3.43" 3.05" 4.73" 2.13" 2.63" 3.36" 1 1/2-11 1/2 17/ mm mm 87.0 mm 77.6 mm mm 54.0 mm 66.7 mm 85.2 mm NPTF UN PS " 5.51" 3.93" 3.70" 5.80" 2.75" 3.06" 4.19" /2 2 1/ mm mm 99.7 mm 94.0 mm mm 69.8 mm 77.6 mm mm NPTF UN Wrench Flats -14

131 Swivels 90 PS Series Female Pipe - Male SE O-Ring Straight Thread Hex 1 Port 1 Hex 2 Port 2 I Part Number ia. Hex 1 Hex 2 Port 1 Port 2 PS /4-18 7/ mm 51.2 mm 35.0 mm 50.2 mm 30.5 mm 19.0 mm 14.3 mm NPTF UNF PS /8-18 9/ mm 55.2 mm 39.4 mm 55.8 mm 32.8 mm 22.2 mm 17.5 mm NPTF UNF PS /2-14 3/ mm 60.3 mm 47.2 mm 69.2 mm 44.0 mm 28.6 mm 22.2 mm NPTF UNF PS / / mm 70.4 mm 61.0 mm 88.5 mm 55.2 mm 35.0 mm 31.8 mm NPTF UN PS /2 1-5/ mm 80.3 mm 63.4 mm 94.9 mm 63.0 mm 41.3 mm 38.1 mm NPTF UN Female Pipe - Female 37 Flare Port 2 I Hex 2 Hex 1 Port 1 Female Pipe - Female NPSM Pipe Swivel Part Number ia. Hex 1 Hex 2 Port 1 Port 2 PS ".56 1/4-18 7/ mm 51.2 mm 37.3 mm 52.5 mm 30.5 mm 19.0 mm 14.3 mm NPTF UNF PS /8-18 9/ mm 55.2 mm 39.9 mm 56.3 mm 32.8 mm 22.2 mm 17.5 mm NPTF UNF PS /2-14 3/ mm 60.3 mm 48.4 mm 70.4 mm 44.0 mm 28.6 mm 22.2 mm NPTF UNF PS / / mm 70.4 mm 59.4 mm 87.0 mm 55.2 mm 35.0 mm 31.8 mm NPTF UN PS /2 1-5/ mm 80.3 mm 64.6 mm 96.2 mm 63.0 mm 41.3 mm 38.1 mm NPTF UN Swivels Hex 1 Port 1 Hex 2 Port 2 I Part Number ia. Hex 1 Hex 2 Port 1 Port 2 PS /4-18 1/ mm 51.2 mm 37.5 mm 52.8 mm 30.5 mm 19.0 mm 17.4 mm NPTF NPSM PS /8-18 3/ mm 55.2 mm 38.4 mm 54.8 mm 32.8 mm 22.2 mm 22.2 mm NPTF NPSM PS /2-14 1/ mm 60.3 mm 47.2 mm 69.2 mm 44.0 mm 28.6 mm 25.4 mm NPTF NPSM PS /4-14 3/ mm 70.4 mm 56.9 mm 84.5 mm 55.2 mm 35.0 mm 31.8 mm NPTF NPSM PS / / mm 80.3 mm 63.1 mm 94.6 mm 63.0 mm 41.3 mm 38.1 mm NPTF NPSM Female Pipe - Female SE Straight Thread Hex 1 Port 1 3 Piece esign Port 2 I Part Number ia. Hex 1 Port 1 Port 2 PS /4-18 7/ mm 51.2 mm 30.5 mm 19.0 mm NPTF UNF PS /8-18 9/ mm 55.2 mm 32.8 mm 22.2 mm NPTF UNF PS /2-14 3/ mm 60.3 mm 44.0 mm 28.6 mm NPTF UNF PS / / mm 70.4 mm 55.2 mm 35.0 mm NPTF UN PS /2 1-5/ mm 80.3 mm 63.0 mm 41.3 mm NPTF UN Port 1 Port 2 ia Part Number Wrench Flats ia. Port 1 Port 2 PS " 4.63" 3.43" 1.27" 2.63" 3.36" 1 1/4-11 1/2 1 5/ mm mm 87.0 mm 32.3 mm 66.7 mm 85.2 mm NPTF UN PS " 4.63" 3.43" 1.27" 2.63" 3.36" 1 1/4-11 1/2 1 5/ mm mm 87.0 mm 32.3 mm 66.7 mm 85.2 mm NPTF UN PS " 5.45" 3.93" 1.52" 3.06" 4.19" /2 2-1/ mm mm 99.7 mm 38.5 mm 77.6 mm mm NPTF UN Wrench Flats -15

132 Swivels 90 PS Series Male 37 Flare - Female Pipe Part Number ia. Hex 1 Port 1 Port 2 Hex 1 Port 1 3 Piece esign Port 2 I PS / / mm 62.0 mm 30.5 mm 19.0 mm UNF NPTF PS / / mm 64.4 mm 32.8 mm 22.2 mm UNF NPTF PS /4-16 1/ mm 68.7 mm 37.8 mm 28.6 mm UNF NPTF PS / / mm 78.8 mm 44.6 mm 35.0 mm UN NPTF PS / / mm 90.0 mm 54.9 mm 41.3 mm UN NPTF Port 1 Port 2 Part Number Wrench Flats ia. Port 1 Port 2 Wrench Flats ia PS " 4.63" 3.43" 1.27" 2.63" 3.36" 1 5/ /4-11 1/ mm mm 87.0 mm 32.3 mm 66.7 mm 85.2 mm UN NPTF PS " 4.63" 3.43" 1.27" 2.63" 3.36" 1 7/ /2-11 1/ mm mm 87.0 mm 32.3 mm 66.7 mm 85.2 mm UN NPTF PS " 5.45" 3.93" 1.52" 3.06" 4.19" 2 1/ / mm mm 99.7 mm 38.5 mm 77.6 mm mm UN NPTF Male 37 Flare - Male 37 Flare Swivels Hex 1 Hex 2 Port 1 3 Piece esign Port 2 I Part Number ia. Hex 1 Hex 2 Port 1 Port 2 PS / / mm 62.0 mm 35.2 mm 50.5 mm 30.5 mm 19.0 mm 14.3 mm UNF UNF PS / / mm 64.4 mm 36.6 mm 53.0 mm 32.8 mm 22.2 mm 17.5 mm UNF UNF PS /4-16 3/ mm 68.7 mm 45.1 mm 67.1 mm 44.0 mm 28.6 mm 22.2 mm UNF UNF PS /8-14 7/ mm 71.2 mm 48.4 mm 70.4 mm 44.0 mm 28.6 mm 22.2 mm UNF UNF PS / / mm 78.8 mm 56.9 mm 85.3 mm 55.2 mm 35.0 mm 31.8 mm UN UN PS / / mm 90.0 mm 61.3 mm 92.9 mm 63.0 mm 41.3 mm 38.1 mm UN UN Port 1 ia Port 2 E Hex Part Number E Hex Wrench Flats ia. Port 1 Port 2 PS " 4.63" 3.43" 2.85" 4.53" 1.88" 2.63" 3.36" 1 5/ / mm mm 87.0 mm 72.4 mm mm 47.6 mm 66.7 mm 85.2 mm UN UN PS " 4.65" 3.43" 3.05" 4.73" 2.13" 2.63" 3.36" 1 7/ / mm mm 87.0 mm 77.6 mm mm 54.0 mm 66.7 mm 85.2 mm UN UN PS " 5.51" 3.93" 3.70" 5.80" 2.75" 3.06" 4.19" 2 1/ / mm mm 99.7 mm 94.0 mm mm 69.8 mm 77.6 mm mm UN UN Wrench Flats Male 37 Flare - Male SE O-Ring Straight Thread Hex 1 Port 1 Hex 2 Port 2 I Part Number ia. Hex 1 Hex 2 Port 1 Port 2 PS / / mm 62.0 mm 35.0 mm 50.2 mm 30.5 mm 19.0 mm 14.3 mm UNF UNF PS / / mm 64.4 mm 39.4 mm 55.8 mm 32.8 mm 22.2 mm 17.5 mm UNF UNF PS /4-16 3/ mm 68.7 mm 47.2 mm 69.2 mm 44.0 mm 28.6 mm 22.2 mm UNF UNF PS / / mm 78.8 mm 61.0 mm 88.5 mm 55.2 mm 35.0 mm 31.8 mm UN UN PS / / mm 90.0 mm 63.4 mm 94.9 mm 63.0 mm 41.3 mm 38.1 mm UN UN -16

133 Swivels 90 PS Series Male 37 Flare - Female 37 Flare Port 2 Part Number ia. Hex 1 Hex 2 Port 1 Port 2 Hex 1 Port 1 Hex 2 I PS / / mm 62.0 mm 37.3 mm 52.5 mm 30.5 mm 19.0 mm 14.3 mm UNF UNF PS / / mm 64.4 mm 39.9 mm 56.3 mm 32.8 mm 22.2 mm 17.5 mm UNF UNF PS /4-16 3/ mm 68.7 mm 48.4 mm 70.4 mm 44.0 mm 28.6 mm 22.2 mm UNF UNF PS / / mm 78.8 mm 59.4 mm 87.0 mm 55.2 mm 35.0 mm 31.8 mm UN UN PS / / mm 90.0 mm 64.6 mm 96.2 mm 63.0 mm 41.3 mm 38.1 mm UN UN Male 37 Flare - Female NPSM Pipe Swivel Hex 1 Port 1 Hex 2 Port 2 Male 37 Flare - Female SE Straight Thread I Part Number ia. Hex 1 Hex 2 Port 1 Port 2 PS / / mm 62.0 mm 37.5 mm 52.8 mm 30.5 mm 19.0 mm 17.4 mm UNF NPSM PS / / mm 64.4 mm 38.4 mm 54.8 mm 32.8 mm 22.2 mm 22.2 mm UNF NPSM PS /4-16 1/ mm 68.7 mm 47.2 mm 69.2 mm 44.0 mm 28.6 mm 25.4 mm UNF NPSM PS / / mm 78.8 mm 56.9 mm 84.5 mm 55.2 mm 35.0 mm 31.8 mm UN NPSM PS / / mm 90.0 mm 63.1 mm 94.6 mm 63.0 mm 41.3 mm 38.1 mm UN NPSM Swivels Part Number ia. Hex 1 Port 1 Port 2 Hex 1 Port 1 Port 2 I PS / / mm 62.0 mm 30.5 mm 19.0 mm UNF UNF PS / / mm 64.4 mm 32.8 mm 22.2 mm UNF UNF PS /4-16 3/ mm 68.7 mm 44.0 mm 28.6 mm UNF UNF PS / / mm 78.8 mm 55.2 mm 35.0 mm UN UN PS / / mm 90.0 mm 63.0 mm 41.3 mm UN UN Male SE O-Ring Straight Thread - Female Pipe Part Number ia. Hex 1 Port 1 Port 2 Hex 1 Port 1 Port 2 I PS / / mm 58.3 mm 30.5 mm 19.0 mm UNF NPTF PS / / mm 59.8 mm 32.8 mm 22.2 mm UNF NPTF PS /4-16 1/ mm 65.9 mm 37.8 mm 28.6 mm UNF NPTF PS / / mm 74.0 mm 44.6 mm 35.0 mm UN NPTF PS / / mm 84.3 mm 54.9 mm 41.3 mm UN NPTF -17

134 Swivels 90 PS Series Male SE O-Ring Straight Thread - Male 37 Flare Part Number ia. Hex 1 Hex 2 Port 1 Port 2 Hex 1 Port 1 Hex 2 Port 2 I PS / / mm 58.3 mm 35.2 mm 50.5 mm 30.5 mm 19.0 mm 14.3 mm UNF UNF PS / / mm 59.8 mm 36.6 mm 53.0 mm 32.8 mm 22.2 mm 17.5 mm UNF UNF PS /4-16 3/ mm 65.9 mm 45.1 mm 67.1 mm 44.0 mm 28.6 mm 22.2 mm UNF UNF PS /8-14 7/ mm 67.5 mm 48.4 mm 70.4 mm 44.0 mm 28.6 mm 22.2 mm UNF UNF PS / / mm 74.0 mm 56.9 mm 85.3 mm 55.2 mm 35.0 mm 31.8 mm UN UN PS / / mm 84.3 mm 61.3 mm 92.9 mm 63.0 mm 41.3 mm 38.1 mm UN UN Male SE O-Ring Straight Thread - Male SE O-Ring Straight Thread Part Number ia. Hex 1 Hex 2 Port 1 Port 2 Swivels Hex 1 Port 1 Hex 2 Port 2 I PS / / mm 58.3 mm 35.0 mm 50.2 mm 30.5 mm 19.0 mm 14.3 mm UNF UNF PS / / mm 59.8 mm 39.4 mm 55.8 mm 32.8 mm 22.2 mm 17.5 mm UNF UNF PS /4-16 3/ mm 65.9 mm 47.2 mm 69.2 mm 44.0 mm 28.6 mm 22.2 mm UNF UNF PS / / mm 74.0 mm 61.0 mm 88.5 mm 55.2 mm 35.0 mm 31.8 mm UN UN PS / / mm 84.3 mm 63.4 mm 94.9 mm 63.0 mm 41.3 mm 38.1 mm UN UN Male SE O-Ring Straight Thread - Female 37 Flare Part Number ia. Hex 1 Hex 2 Port 1 Port 2 Hex 1 Port 1 Hex 2 Port 2 I PS / / mm 58.3 mm 37.3 mm 52.5 mm 30.5 mm 19.0 mm 14.3 mm UNF UNF PS / / mm 59.8 mm 39.9 mm 56.3 mm 32.8 mm 22.2 mm 17.5 mm UNF UNF PS /4-16 3/ mm 65.9 mm 48.4 mm 70.4 mm 44.0 mm 28.6 mm 22.2 mm UNF UNF PS / / mm 74.0 mm 59.4 mm 87.0 mm 55.2 mm 35.0 mm 31.8 mm UN UN PS / / mm 84.3 mm 64.6 mm 96.2 mm 63.0 mm 41.3 mm 38.1 mm UN UN Male SE O-Ring Straight Thread - Female NPSM Pipe Swivel Part Number ia. Hex 1 Hex 2 Port 1 Port 2 Hex 1 Port 1 Hex 2 Port 2 I PS / / mm 58.3 mm 37.5 mm 52.8 mm 30.5 mm 19.0 mm 17.4 mm UNF NPSM PS / / mm 59.8 mm 38.4 mm 54.8 mm 32.8 mm 22.2 mm 22.2 mm UNF NPSM PS /4-16 1/ mm 65.9 mm 47.2 mm 69.2 mm 44.0 mm 28.6 mm 25.4 mm UNF NPSM PS / / mm 74.0 mm 56.9 mm 84.5 mm 55.2 mm 35.0 mm 31.8 mm UN NPSM PS / / mm 84.3 mm 63.1 mm 94.6 mm 63.0 mm 41.3 mm 38.1 mm UN NPSM -18

135 Swivels 90 PS Series Male SE O-Ring Straight Thread - Female SE Straight Thread Part Number ia. Hex 1 Port 1 Port 2 Hex 1 Port 1 Port 2 I PS / / mm 58.3 mm 30.5 mm 19.0 mm UNF UNF PS / / mm 59.8 mm 32.8 mm 22.2 mm UNF UNF PS /4-16 3/ mm 65.9 mm 44.0 mm 28.6 mm UNF UNF PS / / mm 74.0 mm 55.2 mm 35.0 mm UN UN PS / / mm 84.3 mm 63.0 mm 41.3 mm UN UN Female SE Straight Thread - Female Pipe Hex 1 Port 1 Port 2 Female SE Straight Thread - Male 37 Flare I Part Number ia. Hex 1 Port 1 Port 2 PS / / mm 51.2 mm 30.5 mm 19.0 mm UNF NPTF PS / / mm 55.2 mm 32.8 mm 22.2 mm UNF NPTF PS /4-16 1/ mm 60.3 mm 37.8 mm 28.6 mm UNF NPTF PS / / mm 70.4 mm 44.6 mm 35.0 mm UN NPTF PS / / mm 80.3 mm 54.9 mm 41.3 mm UN NPTF Swivels Hex 1 Port 1 Hex 2 Port 2 I Part Number ia. Hex 1 Hex 2 Port 1 Port 2 PS / / mm 51.2 mm 35.2 mm 50.5 mm 30.5 mm 19.0 mm 14.3 mm UNF UNF PS / / mm 55.2 mm 36.6 mm 53.0 mm 32.8 mm 22.2 mm 17.5 mm UNF UNF PS /4-16 3/ mm 60.3 mm 45.1 mm 67.1 mm 44.0 mm 28.6 mm 22.2 mm UNF UNF PS / / mm 70.4 mm 56.9 mm 85.3 mm 55.2 mm 35.0 mm 31.8 mm UN UN PS / / mm 80.3 mm 61.3 mm 92.9 mm 63.0 mm 41.3 mm 38.1 mm UN UN Female SE Straight Thread - Male SE O-Ring Straight Thread Part Number ia. Hex 1 Hex 2 Port 1 Port 2 Hex 1 Port 1 Hex 2 Port 2 I PS / / mm 51.2 mm 35.0 mm 50.2 mm 30.5 mm 19.0 mm 14.3 mm UNF UNF PS / / mm 55.2 mm 39.4 mm 55.8 mm 32.8 mm 22.2 mm 17.5 mm UNF UNF PS /4-16 3/ mm 60.3 mm 47.2 mm 69.2 mm 44.0 mm 28.6 mm 22.2 mm UNF UNF PS / / mm 70.4 mm 61.0 mm 88.5 mm 55.2 mm 35.0 mm 31.8 mm UN UN PS / / mm 80.3 mm 63.4 mm 94.9 mm 63.0 mm 41.3 mm 38.1 mm UN UN -19

136 Swivels 90 PS Series Female SE Straight Thread - Female 37 Flare Hex 1 Port 1 Hex 2 Port 2 I Part Number ia. Hex 1 Hex 2 Port 1 Port 2 PS / / mm 51.2 mm 37.3 mm 52.5 mm 30.5 mm 19.0 mm 14.3 mm UNF UNF PS / / mm 55.2 mm 39.9 mm 56.3 mm 32.8 mm 22.2 mm 17.5 mm UNF UNF PS /4-16 3/ mm 60.3 mm 48.4 mm 70.4 mm 44.0 mm 28.6 mm 22.2 mm UNF UNF PS / / mm 70.4 mm 59.4 mm 87.0 mm 55.2 mm 35.0 mm 31.8 mm UN UN- PS / / mm 80.3 mm 64.6 mm 96.2 mm 63.0 mm 41.3 mm 38.1 mm UN UN Female SE Straight Thread - Female NPSM Pipe Swivel Part Number ia. Hex 1 Hex 2 Port 1 Port 2 Swivels Hex 1 Port 1 Hex 2 Port 2 I PS / / mm 51.2 mm 37.5 mm 52.8 mm 30.5 mm 19.0 mm 17.4 mm UNF NPSM PS / / mm 55.2 mm 38.4 mm 54.8 mm 32.8 mm 22.2 mm 22.2 mm UNF NPSM PS /4-16 1/ mm 60.3 mm 47.2 mm 69.2 mm 44.0 mm 28.6 mm 25.4 mm UNF NPSM PS / / mm 70.4 mm 56.9 mm 84.5 mm 55.2 mm 35.0 mm 31.8 mm UN NPSM PS / / mm 80.3 mm 63.1 mm 94.6 mm 63.0 mm 41.3 mm 38.1 mm UN NPSM Female SE Straight Thread - Female SE Straight Thread Part Number ia. Hex 1 Port 1 Port 2 Hex 1 Port 1 3 Piece esign Port 2 I PS / / mm 51.2 mm 30.5 mm 19.0 mm UNF UNF PS / / mm 55.2 mm 32.8 mm 22.2 mm UNF UNF PS /4-16 3/ mm 60.3 mm 44.0 mm 28.6 mm UNF UNF PS / / mm 70.4 mm 55.2 mm 35.0 mm UN UN PS / / mm 80.3 mm 63.0 mm 41.3 mm UN UN Port 1 Wrench Flats Port 2 ia Part Number Wrench Flats ia. Port 1 Port 2 PS " 4.63" 3.43" 1.27" 2.63" 3.36" 1 5/ / mm mm 87.0 mm 32.3 mm 66.7 mm 85.2 mm UN UN PS " 4.63" 3.43" 1.27" 2.63" 3.36" 1 7/ / mm mm 87.0 mm 32.3 mm 66.7 mm 85.2 mm UN UN PS " 5.45" 3.93" 1.52" 3.06" 4.19" /2 2-1/ mm mm 99.7 mm 38.5 mm 77.6 mm mm UN UN -20

137 Swivels Repair Kits Repair Kits/Seal Options Repair Kits come complete with O-Rings, PTFE ack-up Ring, ap Screws, Locking alls, Retaining Ring and grease fitting. Repair kits are suitable for both current and previous design 90 PS Series Swivels. 1/4" Swivel 3/8" Swivel 1/2" Swivel 3/4" Swivel 1" Swivel PS4-RPR PS6-RPR PS8-RPR PS12-RPR PS16-RPR PS4Y-RPR PS6Y-RPR PS8Y-RPR PS12Y-RPR PS16Y-RPR PS4-RPR PS6-RPR PS8-RPR PS12-RPR PS16-RPR PS4W-RPR PS6W-RPR PS8W-RPR PS12W-RPR PS16W-RPR H2-PS = earing Removal Pneumatic Nipple Seal Options Nitrile (standard unless otherwise designated) = flas W = Ethylene Propylene Y = Fluorocarbon Z = Neoprene For Perfluoroelastomer seal option contact the division. Swivels -21

138 Swivels Introduction S Series S Series Swivels Introduction The S Series Swivel product line complements the Quick oupling ivision s PS Series swivel line by offering a pressure balanced, compact forged body design. s a result of the pressure balanced design, the S Series Swivel does not experience a significant increase in torque as pressure rises. The housing body is forged to provide superior performance and durability in tough applications. This product is great for eliminating hose twist, torque and stress caused by the movement of the hydraulic components where side load to the swivel can be minimized. Specifications ody size 1/4" 3/8" 1/2" 3/4" 1 Maximum Rated Pressure (PSI) * Temperature Range (standard seals) -40 to 250 F Maximum RPM * 07 ports on 1 S Series maximum rated pressure is 2600 psi. Performance ata S Series Swivel (1/4, 3/8, 1/2, 3/4, 1 ) Test Fluid: Oil SUS vs. Pressure rop 3/8" Features 30 1/2" 3/4" Swivels 3000 psi working pressure rating for all sizes. Variety of seal options. Torque value does not significantly increase with pressure. ust seals protect the swivel from damaging environmental contaminants. Field service kits are available for quick and reliable repairs. 360 swivel eliminates long radius bends, hose twist and stress that can cause premature hose failure. Pressure rop in PSI /4" 1" One piece forged housing eliminates a brazed 90 adapter connection. 10 ase hardened for enhanced service life. ompact design to fit into tight areas Flow in USGPM -22

139 Swivels How to Order S Series Port 1 Port 2 ack-up Ring O-Ring Flow Holes Housing O-Ring ack-up Ring O-Ring Retainer Retaining Ring O-Ring Shaft S Part Number: S V -8-8 NI Material and Finish: lank = arbon Steel (12L14) w/hromium-6 Free Plating NI = arbon Steel (12L14)* Nickel Plating Swivels Housing Port Size (1/16 of an inch) Shaft Port Size (1/16 of an inch) Housing Port onfiguration: 01 = Male NPTF 02 = Female NPTF 03 = Male JI 37 egree 05 = Male SE O-Ring Straight Thread 07 = Female NPSM Pipe Swivel 10 = Female SE Straight Thread Seal ode: lank = Nitrile (Standard) E = Ethylene Propylene V = Fluorocarbon Shaft Port onfiguration: 21 = Male NPTF 22 = Female NPTF 23 = Male JI 37 egree 25 = Male SE O-Ring Straight Thread Parker S Series Swivel designator * ontact the ivision for Price and vailability -23

140 Swivels 90 S Series Male Pipe - Male Pipe Port 1 Hex 1 Part Number HEX 1 HEX 2 PORT 1 PORT 2 S " 1.51" 2.19" 1.50".88".88" 1/4-18 NPTF 1/4-18 NPTF 58.7 mm 38.4 mm 55.5 mm 38.0 mm 22.2 mm 22.2 mm S " 1.51" 2.19" 1.50".88".88" 3/8-18 NPTF 3/8-18 NPTF 58.7 mm 38.4 mm 55.5 mm 38.0 mm 22.2 mm 22.2 mm S " 1.84" 2.59" 1.84" 1.06" 1.00" 1/2-14 NPTF 1/2-14 NPTF 69.6 mm 46.8 mm 65.8 mm 46.7 mm 27.0 mm 25.4 mm S " 2.1 2" 3.00" 2.11" 1.38" 1.38" 3/4-14 NPTF 3/4-14 NPTF 85.1 mm 53.9 mm 76.2 mm 53.5 mm 34.9 mm 34.9 mm Port 2 Hex 2 Male Pipe - Female Pipe Port 2 Port 1 Hex 2 Hex 1 Part Number HEX 1 HEX 2 PORT 1 PORT 2 S " 1.51" 1.78" 1.09".88".88" 1/4-18 NPTF 1/4-18 NPTF 58.7 mm 38.4 mm 45.1 mm 27.6 mm 22.2 mm 22.2 mm S " 1.51" 1.78" 1.09".88".88" 3/8-18 NPTF 3/8-18 NPTF 58.7 mm 38.4 mm 45.1 mm 27.6 mm 22.2 mm 22.2 mm S " 1.84" 2.10" 1.35" 1.06" 1.00" 1/2-14 NPTF 1/2-14 NPTF 69.6 mm 46.8 mm 53.3 mm 34.3 mm 27.0 mm 25.4 mm S " 2.12" 2.39" 1.50" 1.38" 1.38" 3/4-14 NPTF 3/4-14 NPTF 85.1 mm 53.9 mm 60.7 mm 38.0 mm 34.9 mm 34.9 mm Swivels Male Pipe - Male 37 Flare Port 1 Port 2 Hex 2 Hex 1 Part Number HEX 1 HEX 2 PORT 1 PORT 2 S " 1.51" 2.19" 1.50".88".88" 1/4-18 NPTF 7/16-20UNF 58.7 mm 38.4 mm 55.5 mm 38.0 mm 22.2 mm 22.2 mm S " 1.51" 2.19" 1.50".88".88" 3/8-18 NPTF 9/16-18UNF 58.7 mm 38.4 mm 55.5 mm 38.0 mm 22.2 mm 22.2 mm S " 1.84" 2.59" 1.84" 1.06" 1.00" 1/2-14 NPTF 3/4-16UNF 69.6 mm 46.8 mm 65.8 mm 46.7 mm 27.0 mm 25.4 mm S " 2.12" 3.07" 2.17" 1.38" 1.38" 3/4-14 NPTF 1-1/16-12UN 85.1 mm 53.9 mm 77.9 mm 55.2 mm 34.9 mm 34.9 mm S " 2.54" 3.01" 2.11" 1.63" 1.69" /2 NPTF 1-5/16-12UN mm 64.5 mm 76.5 mm 53.6 mm 41.4 mm 42.9 mm Male Pipe - Female NPSM Pipe Swivel Port 2 Port 1 Hex 2 Hex 1 Part Number HEX 1 HEX 2 PORT 1 PORT 2 S " 1.51" 2.05" 1.36".88".69" 1/4-18 NPTF 1/4-18 NPSM 58.7 mm 38.4 mm 52.0 mm 34.5 mm 22.2 mm 17.5 mm S " 1.51" 2.07" 1.38".88".88" 3/8-18 NPTF 3/8-18 NPSM 58.7 mm 38.4 mm 52.5 mm 35.1 mm 22.2 mm 22.2 mm S " 1.84" 2.32" 1.57" 1.06" 1.00" 1/2-14 NPTF 1/2-14 NPSM 69.6 mm 46.8 mm 59.0 mm 39.9 mm 27.0 mm 25.4 mm S " 2.12" 2.74" 1.85" 1.38" 1.25" 3/4-14 NPTF 3/4-14 NPSM 85.1 mm 53.9 mm 69.5 mm 46.9 mm 34.9 mm 31.8 mm S " 2.54" 3.14" 2.23" 1.63" 1.69" /2 NPTF /2 NPSM mm 64.5 mm 79.8 mm 56.6 mm 41.4 mm 42.9 mm Male Pipe - Female SE Straight Thread Port 1 Hex 1 Part Number HEX 1 HEX 2 PORT 1 PORT 2 S " 1.51" 1.78" 1.09".88".88" 3/8-18 NPTF 9/16-18UNF 58.7 mm 38.4 mm 45.1 mm 27.6 mm 22.2 mm 22.2 mm S " 1.84" 2.10" 1.35" 1.06" 1.00" 1/2-14 NPTF 3/4-16UNF 69.6 mm 46.8 mm 53.3 mm 34.3 mm 27.0 mm 25.4 mm S " 2.12" 2.54" 1.65" 1.38" 1.38" 3/4-14 NPTF 1-1/16-12UN 85.1 mm 53.9 mm 64.5 mm 41.9 mm 34.9 mm 34.9 mm Port 2 Hex 2-24

141 Swivels 90 S Series Female Pipe - Male Pipe Port 2 Port 1 Hex 2 Hex 1 Part Number HEX 1 HEX 2 PORT 1 PORT 2 S " 1.39" 2.19" 1.50".88".88" 1/4-18 NPTF 1/4-18 NPTF 55.6 mm 35.4 mm 55.5 mm 38.0 mm 22.2 mm 22.2 mm S " 1.39" 2.19" 1.50".88".88" 3/8-18 NPTF 3/8-18 NPTF 55.6 mm 35.4 mm 55.5 mm 38.0 mm 22.2 mm 22.2 mm S " 1.57" 2.59" 1.84" 1.06" 1.00" 1/2-14 NPTF 1/2-14 NPTF 62.7 mm 40.0 mm 65.8 mm 46.7 mm 27.0 mm 25.4 mm S " 1.92" 3.00" 2.11" 1.38" 1.38" 3/4-14 NPTF 3/4-14 NPTF 80.0 mm 48.8 mm 76.2 mm 53.5 mm 34.9 mm 34.9 mm Female Pipe - Female Pipe Hex 1 Part Number HEX 1 HEX 2 PORT 1 PORT 2 Port 2 Port 1 Hex 2 S " 1.39" 1.78" 1.09".88".88" 1/4-18 NPTF 1/4-18 NPTF 55.6 mm 35.4 mm 45.1 mm 27.6 mm 22.2 mm 22.2 mm S " 1.39" 1.78" 1.09".88".88" 3/8-18 NPTF 3/8-18 NPTF 55.6 mm 35.4 mm 45.1 mm 27.6 mm 22.2 mm 22.2 mm S " 1.57" 2.10" 1.35" 1.06" 1.00" 1/2-14 NPTF 1/2-14 NPTF 62.7 mm 40.0 mm 53.3 mm 34.3 mm 27.0 mm 25.4 mm S " 1.92" 2.39" 1.50" 1.38" 1.38" 3/4-14 NPTF 3/4-14 NPTF 80.0 mm 48.8 mm 60.7 mm 38.0 mm 34.9 mm 34.9 mm Female Pipe - Male 37 Flare Port 1 Port 2 Hex 2 Hex 1 Part Number HEX 1 HEX 2 PORT 1 PORT 2 S " 1.39" 2.19" 1. 50".88".88" 1/4-18 NPTF 7/16-20UNF 55.6 mm 35.4 mm 55.5 mm 38.0 mm 22.2 mm 22.2 mm S " 1.39" 2.19" 1.50".88".88" 3/8-18 NPTF 9/16-18UNF 55.6 mm 35.4 mm 55.5 mm 38.0 mm 22.2 mm 22.2 mm S " 1.57" 2.59" 1.84" 1.06" 1.00" 1/2-14 NPTF 3/4-16UNF 62.7 mm 40.0 mm 65.8 mm 46.7 mm 27.0 mm 25.4 mm S " 1.92" 3.07" 2.17" 1.38" 1.38" 3/4-14 NPTF 1-1/16-12UN 80.0 mm 48.8 mm 77.9 mm 55.2 mm 34.9 mm 34.9 mm S " 2.13" 3.01" 2.11" 1.63" 1.69" /2 NPTF 1-5/16-12UN 90.2 mm 54.1 mm 76.5 mm 53.6 mm 41.4 mm 42.9 mm Swivels Female Pipe - Female SE Straight Thread Port 1 Hex 1 Part Number HEX 1 HEX 2 PORT 1 PORT 2 S " 1.39" 1.78" 1.09".88".88" 3/8-18 NPTF 9/16-18UNF 55.6 mm 35.4 mm 45.1 mm 27.6 mm 22.2 mm 22.2 mm S " 1.57" 2.10" 1.35" 1.06" 1.00" 1/2-14 NPTF 3/4-16UNF 62.7 mm 40.0 mm 53.3 mm 34.3 mm 27.0 mm 25.4 mm S " 1.92" 2.54" 1.65" 1.38" 1.38" 3/4-14 NPTF 1-1/16-12UN 80.0 mm 48.8 mm 64.5 mm 41.9 mm 34.9 mm 34.9 mm Port 2 Hex 2 Female Pipe - Female NPSM Pipe Swivel Port 2 Port 1 Hex 2 Hex 1 Part Number HEX 1 HEX 2 PORT 1 PORT 2 S " 1.39" 2.05" 1.36".88".69" 1/4-18 NPTF 1/4-18 NPSM 55.6 mm 35.4 mm 52.0 mm 34.5 mm 22.2 mm 17.5 mm S " 1.39" 2.07" 1.38".88".88" 3/8-18 NPTF 3/8-18 NPSM 55.6 mm 35.4 mm 52.5 mm 35.1 mm 22.2 mm 22.2 mm S " 1.57" 2.32" 1.57" 1.06" 1.00" 1/2-14 NPTF 1/2-14 NPSM 62.7 mm 40.0 mm 59.0 mm 39.9 mm 27.0 mm 25.4 mm S " 1.92" 2.74" 1.85" 1.38" 1.25" 3/4-14 NPTF 3/4-14 NPSM 80.0 mm 48.8 mm 69.5 mm 46.9 mm 34.9 mm 31.8 mm S " 2.13" 3.14" 2.23" 1.63" 1.69" /2 NPTF /2 NPSM 90.2 mm 54.1 mm 79.8 mm 56.6 mm 41.4 mm 42.9 mm -25

142 Swivels 90 S Series Male 37 Flare - Male Pipe Port 2 Port 1 Hex 2 Hex 1 Part Number HEX 1 HEX 2 PORT 1 PORT 2 S " 1.61" 2.19" 1.50".88".88" 7/16-20UNF 1/4-18 NPTF 61.2 mm 40.9 mm 55.5 mm 38.0 mm 22.2 mm 22.2 mm S " 1.61" 2.19" 1.50".88".88" 9/16-18UNF 3/8-18 NPTF 61.2 mm 40.9 mm 55.5 mm 38.0 mm 22.2 mm 22.2 mm S " 1.73" 2.59" 1.84" 1.06" 1.00" 3/4-16UNF 1/2-14 NPTF 66.8 mm 44.0 mm 65.8 mm 46.7 mm 27.0 mm 25.4 mm S " 2.10" 3.00" 2.11" 1.38" 1.38" 1-1/16-12UN 3/4-14 NPTF 84.6 mm 53.4 mm 76.2 mm 53.5 mm 34.9 mm 34.9 mm Male 37 Flare - Female Pipe Port 2 Port 1 Hex 2 Hex 1 Part Number HEX 1 HEX 2 PORT 1 PORT 2 S " 1.61" 1.78" 1.09".88".88" 7/16-20UNF 1/4-18 NPTF 61.2 mm 40.9 mm 45.1 mm 27.6 mm 22.2 mm 22.2 mm S " 1.61" 1.78" 1.09".88".88" 9/16-18UNF 3/8-18 NPTF 61.2 mm 40.9 mm 45.1 mm 27.6 mm 22.2 mm 22.2 mm S " 1.73" 2.10" 1.35" 1.06" 1.00" 3/4-16UNF 1/2-14 NPTF 66.8 mm 44.0 mm 53.3 mm 34.3 mm 27.0 mm 25.4 mm S " 2.10" 2.39" 1.50" 1.38" 1.38" 1-1/16-12UN 3/4-14 NPTF 84.6 mm 53.4 mm 60.7 mm 38.0 mm 34.9 mm 34.9 mm Swivels Male 37 Flare - Male 37 Flare Port 1 Port 2 Hex 2 Hex 1 Part Number HEX 1 HEX 2 PORT 1 PORT 2 S " 1.61" 2.19" 1.50".88".88" 7/16-20UNF 7/16-20UNF 61.2 mm 40.9 mm 55.5 mm 38.0 mm 22.2 mm 22.2 mm S " 1.61" 2.19" 1.50".88".88" 9/16-18UNF 9/16-18UNF 61.2 mm 40.9 mm 55.5 mm 38.0 mm 22.2 mm 22.2 mm S " 1.73" 2.59" 1.84" 1.06" 1.00" 3/4-16UNF 3/4-16UNF 66.8 mm 44.0 mm 65.8 mm 46.7 mm 27.0 mm 25.4 mm S " 1.73" 2.59" 1.84" 1.06" 1.00" 7/8-14UNF 7/8-14UNF 66.8 mm 44.0 mm 65.8 mm 46.7 mm 27.0 mm 25.4 mm S " 2.10" 3.07" 2.17" 1.38" 1.38" 1-1/16-12UN 1-1/16-12UN 84.6 mm 53.4 mm 77.9 mm 55.2 mm 34.9 mm 34.9 mm S " 2.64" 3.01" 2.11" 1.63" 1.69" 1-5/16-12UN 1-5/16-12UN mm 67.1 mm 76.5 mm 53.6 mm 41.4 mm 42.9 mm Male 37 Flare - Female NPSM Pipe Swivel Port 2 Port 1 Hex 2 Hex 1 Part Number HEX 1 HEX 2 PORT 1 PORT 2 S " 1.61" 2.05" 1.36".88".69" 7/16-20UNF 1/4-18 NPSM 61.2 mm 40.9 mm 52.0 mm 34.5 mm 22.2 mm 17.5 mm S " 1.61" 2.07" 1.38".88".88" 9/16-18UNF 3/8-18 NPSM 61.2 mm 40.9 mm 52.5 mm 35.1 mm 22.2 mm 22.2 mm S " 1.73" 2.32" 1.57" 1.06" 1.00" 3/4-16UNF 1/2-14 NPSM 66.8 mm 44.0 mm 59.0 mm 39.9 mm 27.0 mm 25.4 mm S " 2.10" 2.74" 1.85" 1.38" 1.25" 1-1/16-12UN 3/4-14 NPSM 84.6 mm 53.4 mm 69.5 mm 46.9 mm 34.9 mm 31.8 mm Male 37 Flare - Female SE Straight Thread Port 1 Hex 1 Part number HEX 1 HEX 2 PORT 1 PORT 2 S " 1.61" 1.78" 1.09".88".88" 9/16-18UNF 9/16-18UNF 61.2 mm 40.9 mm 45.1 mm 27.6 mm 22.2 mm 22.2 mm S " 1.73" 2.10" 1.35" 1.06" 1.00" 3/4-16UNF 3/4-16UNF 66.8 mm 44.0 mm 53.3 mm 34.3 mm 27.0 mm 25.4 mm S " 2.10" 2.54" 1.65" 1.38" 1.38" 1-1/16-12UN 1-1/16-12UN 84.6 mm 53.4 mm 64.5 mm 41.9 mm 34.9 mm 34.9 mm Port 2 Hex 2-26

143 Swivels 90 S Series Male SE O-Ring Straight Thread - Male Pipe Port 1 Hex 1 Part number HEX 1 HEX 2 PORT 1 PORT 2 S " 1.33" 2.19" 1.50".88".88" 9/16-18UNF 3/8-18 NPTF 54.1 mm 33.8 mm 55.5 mm 38.0 mm 22.2 mm 22.2 mm S " 1.50" 2.59" 1.84" 1.06" 1.00" 3/4-16UNF 1/2-14 NPTF 61.0 mm 38.2 mm 65.8 mm 46.7 mm 27.0 mm 25.4 mm S " 2.17" 3.00" 2.11" 1.38" 1.38" 1-1/16-12UN 3/4-14 NPTF 86.4 mm 55.2 mm 76.2 mm 53.5 mm 34.9 mm 34.9 mm Port 2 Hex 2 Male SE O-Ring Straight Thread - Female Pipe Port 2 Port 1 Hex 2 Hex 1 Part number HEX 1 HEX 2 PORT 1 PORT 2 S " 1.33" 1.78" 1.09".88".88" 9/16-18UNF 3/8-18 NPTF 54.1 mm 33.8 mm 45.1 mm 27.6 mm 22.2 mm 22.2 mm S " 1.50" 2.10" 1.35" 1.06" 1.00" 3/4-16UNF 1/2-14 NPTF 61.0 mm 38.2 mm 53.3 mm 34.3 mm 27.0 mm 25.4 mm S " 2.17" 2.39" 1.50" 1.38" 1.38" 1-1/16-12UN 3/4-14 NPTF 86.4 mm 55.2 mm 60.7 mm 38.0 mm 34.9 mm 34.9 mm Male SE O-Ring Straight Thread - Male 37 Flare Port 2 Port 1 Hex 2 Hex 1 Part number HEX 1 HEX 2 PORT 1 PORT 2 S " 1.33" 2.19" 1.50".88".88" 9/16-18UNF 9/16-18UNF 54.1 mm 33.8 mm 55.5 mm 38.0 mm 22.2 mm 22.2 mm S " 1.50" 2.59" 1.84" 1.06" 1.00" 3/4-16UNF 3/4-16UNF 61.0 mm 38.2 mm 65.8 mm 46.7 mm 27.0 mm 25.4 mm S " 1.64" 2.59" 1.84" 1.06" 1.00" 7/8-14UNF 7/8-14UNF 64.5 mm 41.7 mm 65.8 mm 46.7 mm 27.0 mm 25.4 mm S " 2.17" 3.07" 2.17" 1.38" 1.38" 1-1/16-12UN 1-1/16-12UN 86.4 mm 55.2 mm 77.9 mm 55.2 mm 34.9 mm 34.9 mm S " 2.33" 3.01" 2.11" 1.63" 1.69" 1-5/16-12UN 1-5/16-12UN 95.3 mm 59.2 mm 76.5 mm 53.6 mm 41.4 mm 42.9 mm Swivels Male SE O-Ring Straight Thread - Female NPSM Pipe Swivel Port 2 Port 1 Hex 2 Hex 1 Part number HEX 1 HEX 2 PORT 1 PORT 2 S " 1.33" 2.07" 1.38".88".88" 9/16-18UNF 3/8-18 NPSM 54.1 mm 33.8 mm 52.5 mm 35.1 mm 22.2 mm 22.2 mm S " 1.50" 2.32" 1.57" 1.06" 1.00" 3/4-16UNF 1/2-14 NPSM 61.0 mm 38.2 mm 59.0 mm 39.9 mm 27.0 mm 25.4 mm S " 2.17" 2.74" 1.85" 1.38" 1.25" 1-1/16-12UN 3/4-14 NPSM 86.4 mm 55.2 mm 69.5 mm 46.9 mm 34.9 mm 31.8 mm S " 2.33" 3.14" 2.23" 1.63" 1.69" 1-5/16-12UN /2 NPSM 95.3 mm 59.2 mm 79.8 mm 56.6 mm 41.4 mm 42.9 mm Male SE O-Ring Straight Thread - Female SE Straight Thread Port 1 Hex 1 Part number HEX 1 HEX 2 PORT 1 PORT 2 S " 1.33" 1.78" 1.09".88".88" 9/16-18UNF 9/16-18UNF 54.1 mm 33.8 mm 45.1 mm 27.6 mm 22.2 mm 22.2 mm S " 1.50" 2.10" 1.35" 1.06" 1.00" 3/4-16UNF 3/4-16UNF 61.0 mm 38.2 mm 53.3 mm 34.3 mm 27.0 mm 25.4 mm S " 2.17" 2.54" 1.65" 1.38" 1.38" 1-1/16-12UN 1-1/16-12UN 86.4 mm 55.2 mm 64.5 mm 41.9 mm 34.9 mm 34.9 mm Port 2 Hex 2-27

144 Swivels Swivels Repair Kits Repair Kits/Seal Options Repair Kits come complete with primary O-Rings, PTFE backup rings, external and internal dust seals, retaining ring and instruction sheet. Nitrile Seals EP Seals Fluorocarbon Seals Size Kit Number Size Kit Number Size Kit Number -4/-6 RK-4/6N -4/-6 RK-4/6E -4/-6 RK-4/6V -8/-10 RK-8N -8/-10 RK-8E -8/-10 RK-8V -12 RK-12N -12 RK-12E -12 RK-12V -16 RK-16N -16 RK-16E -16 RK-16V -28

145 heck Valves E heck Valves E-1

146 E heck Valves heck Valves Introduction Multiple Hydraulic System pplications Parker heck Valves are unidirectional flow control devices used primarily in hydraulic systems to eliminate potential damage caused by fluid back pressure. Offered in many configurations, Parker can satisfy most hydraulic system applications. Parker's in-line style of heck Valves are available in a variety of sizes, pressure ratings, flow capacities and crack pressures. E-2

147 heck Valves Table of ontents Introduction...E-2 Selection Guide...E-4 Features & General Technical Information...E-4 T Series...E-5 E-7 Ordering Information...E-8 V Series...E-9 E-11 Ordering Information...E-11 E heck Valves E-3

148 heck Valves Technical Information Pressure at inlet port. Poppet is moved off seat. Flow is allowed through valve. Selection Guide Seat Poppet Rated rack ody Size Material Pressure Pressure V Series 1/4-1" Steel 3000 PSI PSI T Series 1/4-1 1/4" Steel 5000 PSI PSI Inlet Port Outlet Port Features Parker s heck Valves employ several unique features that insure years of trouble-free operation. Specific features for each series of check valves are listed within this section. Inlet Port Seat Poppet Pressure at outlet port. Poppet is against seat. Flow is blocked at seat. Outlet Port rack Pressure rack pressure refers to the amount of fluid pressure in the free flow direction required to move the poppet off the seat. The normal crack pressure setting is 5 PSI; however, other crack pressures are available to allow the check valve to perform special circuit functions, or operate under unique conditions. heck valves are not field repairable or adjustable. rack pressure settings are made at the factory only. E heck Valves pplications TYPIL HYRULI IRUIT. THE HEK VLVE IS USE TO PROTET THE PUMP Y PREVENTING PRESSURE FROM RETURN- ING TO THE OUTLET PORT OF THE PUMP. HEK VLVE PUMP TNK RELIEF VLVE TNK ONTROL VLVE YLINER Oil cooler bypass circuit. If return line pressure becomes excessive due to resistance through oil cooler (such as startup in cold weather). heck valve opens and allows oil to bypass the cooler and flow to the tank. The graphic symbol for a check-valve is: E-4

149 heck Valves T Series Parker T Series heck Valves Offer the Features of a ompact ody Size, and 5000 PSI Maximum Operating Pressure. The T Series check valves utilize the dependable, internal design features found in Parker check valves, but with the added benefit and convenience of compact design. Sizes are available from 1/4" to 1-1/4" with six different Fitting Styles. The T Series expands Parker's high quality product line of versatile and efficient check valves. Features: 1. ompact esign. Easy to plumb into tight circuits. 2. ll steel construction. No internal gaskets or seals to wear out. 3. One-piece body eliminates threads and seals that may be potential leakage points. 4. Smooth flow stream. Poppet spring is isolated from flow stream. 5. Heat treated poppet to resist damage from shocks and surges. 6. Variety of end fittings. 7. Optional crack pressures available from 1 to 200 PSI. 8. hromium-6 Free plated exterior finish. 9. Nitrile O-Ring included on MO and MS fittings. 10. aptive O-Ring Groove is standard on MS end fittings. FLOW T-MFMF Male Flare 37 JI Inlet to Male Flare 37 JI Outlet FLOW T-MFMO Male Flare 37 JI Inlet to Male O-Ring oss Outlet FLOW T-MOMF Male O-Ring oss Inlet to Male Flare 37 JI Outlet E heck Valves FLOW FLOW FLOW T-MOMS Male O-Ring oss Inlet to Male Seal-Lok Outlet T-MSMO Male Seal-Lok Inlet to Male O-Ring oss Outlet T-MSMS Male Seal-Lok Inlet to Male Seal-Lok Outlet E-5

150 heck Valves T Series Specifications The T Series check valves have a Maximum Operating Pressure of 5000 PSI. Standard crack pressures are 1, 5, and 65 PSI depending on the port size and configuration. Other crack pressures up to 200 PSI in 5 PSI increments are available upon request. T-MFMF Male Flare 37 JI Inlet to Male Flare 37 JI Outlet Valve Hex ** Std rack Size Inlet Port Outlet Port Size Pressures (inch) Part Number Thread imensions (in) Thread (inch) (PSI) FLOW E F 3/8 T-370-MFMF-** 9/16-18 UNF /16-18 UNF.75 1, 5, 65 1/2 T-500-MFMF-** 3/4-16 UNF /4-16 UNF.88 5, 65 5/8 T-620-MFMF-** 7/8-14 UNF /8-14 UNF /4 T-750-MFMF-** 1-1/16-12 UN /16-12 UN , 5, 65 F Hex E 1 T-1000-MFMF-** 1-5/16-12 UN /16-12 UN , /4 T-1250-MFMF-** 1-5/8-12 UN /8-12 UN , 5 T-MFMO Male Flare 37 JI Inlet to Male O-Ring oss Outlet Valve Hex ** Std rack Size Inlet Port Outlet Port Size Pressures (inch) Part Number Thread imensions (in) Thread (inch) (PSI) E F E heck Valves FLOW F Hex E 1/4 T-250-MFMO-** 7/16-20 UNF /16-20 UNF /8 T-370-MFMO-** 9/16-18 UNF /16-18 UNF.75 1, 5, 65 1/2 T-500-MFMO-** 3/4-16 UNF /4-16 UNF.88 5, 65 5/8 T-620-MFMO-** 7/8-14 UNF /8-14 UNF /4 T-750-MFMO-** 1-1/16-12 UN /16-12 UN , 5, 65 1 T-1000-MFMO-** 1-5/16-12 UN /16-12 UN , /4 T-1250-MFMO-** 1-5/8-12 UN /8-12 UN , 5 T-MOMF Male O-Ring oss Inlet to Male Flare 37 JI Outlet Valve Hex ** Std rack Size Inlet Port Outlet Port Size Pressures (inch) Part Number Thread imensions (in) Thread (inch) (PSI) E F 1/4 T-250-MOMF-** 7/16-20 UNF /16-20 UNF.62 5 FLOW 3/8 T-370-MOMF-** 9/16-18 UNF /16-18 UNF.75 1, 5, 65 1/2 T-500-MOMF-** 3/4-16 UNF /4-16 UNF.88 5, 65 5/8 T-620-MOMF-** 7/8-14 UNF /8-14 UNF /4 T-750-MOMF-** 1-1/16-12 UN /16-12 UN , 5, 65 F Hex E 1 T-1000-MOMF-** 1-5/16-12 UN /16-12 UN , /4 T-1250-MOMF-** 1-5/8-12 UN /8-12 UN , 5 E-6

151 heck Valves T Series T-MOMS Male O-Ring oss Inlet to Male Seal-Lok Outlet Valve Hex ** Std rack Size Inlet Port Outlet Port Size Pressures (inch) Part Number Thread imensions (in) Thread (inch) (PSI) E F FLOW 1/4 T-250-MOMS-** 7/16-20 UNF /16-18 UNF /8 T-370-MOMS-** 9/16-18 UNF /16-16 UN.75 1, 5, 65 1/2 T-500-MOMS-** 3/4-16 UNF /16-16 UN.88 5, 65 5/8 T-620-MOMS-** 7/8-14 UNF UNS /4 T-750-MOMS-** 1-1/16-12 UN /16-12 UN , 5, 65 F Hex E 1 T-1000-MOMS-** 1-5/16-12 UN /16-12 UN , /4 T-1250-MOMS-** 1-5/8-12 UN /16-12 UN , 5 T-MSMO Male Seal-Lok Inlet to Male O-Ring oss Outlet FLOW F Hex T-MSMS Male Seal-Lok Inlet to Male Seal-Lok Outlet FLOW F Hex E E Valve Hex ** Std rack Size Inlet Port Outlet Port Size Pressures (inch) Part Number Thread imensions (in) Thread (inch) (PSI) E F 3/8 T-370-MSMO-** 11/16-16 UN /16-18 UNF.75 1, 5, 65 1/2 T-500-MSMO-** 13/16-16 UN /4-16 UNF.88 5, 65 5/8 T-620-MSMO-** 1-14 UNS /8-14 UNF /4 T-750-MSMO-** 1-3/16-12 UN /16-12 UN , 5, 65 1 T-1000-MSMO-** 1-7/16-12 UN /16-12 UN , /4 T-1250-MSMO-** 1-11/16-12 UN /8-12 UN , 5 Valve Hex ** Std rack Size Inlet Port Outlet Port Size Pressures (inch) Part Number Thread imensions (in) Thread (inch) (PSI) E F 3/8 T-370-MSMS-** 11/16-16 UN /16-16 UN.75 1, 5, 65 1/2 T-500-MSMS-** 13/16-16 UN /16-16 UN.88 5, 65 5/8 T-620-MSMS-** 1-14 UNS UNS /4 T-750-MSMS-** 1-3/16-12 UN /16-12 UN , 5, 65 1 T-1000-MSMS-** 1-7/16-12 UN /16-12 UN , /4 T-1250-MSMS-** 1-11/16-12 UN /16-12 UN , 5 E heck Valves E-7

152 heck Valves T Series Flow ata 110 T Series (1/4" & 3/8") Test Fluid: Oil SUS 100 T Series (1/2", 5/8" & 3/4") Test Fluid: Oil SUS Pressure rop in PSI /4" (T-250) 3/8" (T-370) Flow in USGPM Pressure rop in PSI /2" & 5/8" (T-500 / T-620) 3/4" (T-750) Flow in USGPM 200 T Series (1" & 1-1/4") Test Fluid: Oil SUS E heck Valves Pressure rop in PSI " (T-1000) 1-1/4" (T-1250) Flow in USGPM Ordering Information T- - - SERIES SIZE 0-1/ /8" 0-1/2 50 " 0-5/ /4" -1" /4" RK PRESSURE 01-1 PSI 05-5 PSI PSI Other rack Pressures up to 200 PSI in 5 PSI increments are available. ontact the ivision for price and delivery on non-standard crack pressures FITTING STYLE MFMF - Male Flare to let In Male Flare Outlet MFMO- Male Flare to let In Male O- Ring oss et Outl MOMF - Male O- Ring oss to Inlet Male Flare et Outl MOMS- Male O- Ring oss to Inlet Male Face Outlet Seal MSMO- Male Face to Inlet Seal Male O- Ring oss Outlet MSMS- Male Face to Inlet Seal Male Fac Outlet eseal E-8

153 heck Valves V Series V Series heck Valves Offer Port Thread Options for Special Plumbing Requirements Parker s V Series check valves are a rugged built and versatile product designed to protect hydraulic systems from fluid back pressure. The V Series compliments the T Series by adding the feature of modular design. This two piece body design offers more end configurations than a one piece body. The larger body also results in less pressure drop and increased performance. The V Series are in-line unidirectional valves, available in sizes 1/4 to 1, with a pressure rating of up to 3000 PSI, flow capacities to 100 GPM, and a variety of port options. Standard spring crack pressures are 5 and 65 PSI. Other crack pressures available upon request. Features: 1. Nitrile O-ring is standard in the body assembly. Note port O-rings are included on the MO and MS port options. 2. vailable with variety of thread design options. 3. ll-steel construction 4. Valve seats resist damage from shocks, surges and contamination. 5. Poppet has an oil retention groove that lubricates the bore and eliminates galling. 6. Poppet spring is isolated from the liquid flow stream, minimizing turbulence. 7. Poppet is heat treated to help prevent damage from shocks, surges and galling. 8. lose tolerance fit between poppet and poppet retainer creates a cushion that protects valve from surge shock damage. 9. Optional crack pressures availible upon request E heck Valves V-MFMF Male Flare 37 JI Inlet to Male Flare 37 JI Outlet V-FOFO Female O-ring oss Inlet to Female O-ring oss Outlet V-MOMS Male O-Ring oss Inlet to Male Seal-Lok Outlet V-FPFP Female Pipe Thread Inlet to Female Pipe Thread Outlet E-9

154 heck Valves Specifications V-MFMF Male Flare 37 JI Inlet to Male Flare 37 JI Outlet HEX TYP Max Valve ** Std rack Operating Size Inlet Port imensions Outlet Port Pressures Pressure (inch) Part Number Thread (inch) Thread (PSI) (PSI) Hex 1/4 V-250-MFMF-** 7/16-20 UNF /16-20 UNF 5, /8 V-370-MFMF-** 9/16-18 UNF /16-18 UNF 5, /2 V-500-MFMF-** 3/4-16 UNF /4-16 UNF 5, /8 V-620-MFMF-** 7/8-14 UNF /8-14 UNF 5, /4 V-750-MFMF-** 1-1/16-12 UN /16-12 UN 5, V-1000-MFMF-** 1-5/16-12 UN /16-12 UN 5, V-MOMS Male O-Ring oss Inlet to Male Seal-Lok Outlet E heck Valves HEX TYP V-FOFO Female O-ring oss Inlet to Female O-ring oss Outlet HEX TYP Max Valve ** Std rack Operating Size Inlet Port imensions Outlet Port Pressures Pressure (inch) Part Number Thread (inch) Thread (PSI) (PSI) Hex 1/4 V-250-MOMS-** 7/16-20 UNF /16-18 UNF 5, /8 V-370-MOMS-** 9/16-18 UNF /16-16 UN 5, /2 V-500-MOMS-** 3/4-16 UNF /16-16 UN 5, /8 V-620-MOMS-** 7/8-14 UNF UNS 5, /4 V-750-MOMS-** 1-1/16-12 UN /16-12 UN 5, V-1000-MOMS-** 1-5/16-12 UN /16-12 UN 5, Max Valve ** Std rack Operating Size Inlet Port imensions Outlet Port Pressures Pressure (inch) Part Number Thread (inch) Thread (PSI) (PSI) Hex 1/4 V-250-FOFO-** 7/16-20 UNF /16-20 UNF 5, /8 V-370-FOFO-** 9/16-18 UNF /16-18 UNF 5, /2 V-500-FOFO-** 3/4-16 UNF /4-16 UNF 5, /8 V-620-FOFO-** 7/8-14 UNF /8-14 UNF 5, /4 V-750-FOFO-** 1-1/16-12 UN /16-12 UN 5, V-1000-FOFO-** 1-5/16-12 UN /16-12 UN 5, E-10

155 heck Valves V Series V-FPFP Female Pipe Thread Inlet to Female Pipe Thread Outlet HEX TYP Max Valve ** Std rack Operating Size Inlet Port imensions Outlet Port Pressures Pressure (inch) Part Number Thread (inch) Thread (PSI) (PSI) Hex 1/4 V-250-FPFP-** 1/4-18 NPSF /4-18 NPSF 5, /8 V-370-FPFP-** 3/8-18 NPSF /8-18 NPSF 5, /2 V-500-FPFP-** 1/2-14 NPSF /2-14 NPSF 5, /4 V-750-FPFP-** 3/4-14 NPSF /4-14 NPSF 5, V-1000-FPFP-** /2 NPSF /2 NPSF 5, Flow ata 70 V Series (1/4" & 3/8") Test Fluid: Oil SUS 100 V Series (1/2", 5/8", 3/4" & 1") Test Fluid: Oil SUS Pressure rop in PSI /4" (V-250) 3/8" (V-370) Pressure rop in PSI /2" & 5/8" (V-500 / V-620) 3/4" (V-750) 1" (V-1000) E heck Valves Flow in USGPM Flow in USGPM Ordering Information V- - - SERIES SIZE 250-1/4" 370-3/8" 500-1/2" 620-5/ /4" " RK PRESSURE 05-5 PSI PSI Other rack Pressures up to 200 PSI in 5 PSI increments are available. ontact the ivision for price and delivery on non-standard crack pressures FITTING STYLE FOFO - Female O-Ring oss Inlet to Female O-Ring oss Outlet MFMF - Male Flare Inlet to Male Flare Outlet MOMS - Male O-Ring oss Inlet to Male Seal-Lok Outlet FPFP - Female Pipe Inlet to Female Pipe Outlet E-11

156 Quick oupling iagnostic Products F iagnostic F-1

157 iagnostic Products Introduction Increasing productivity and profitability are the key elements for a company to successfully compete in the world market today. Reduced machine downtime during initial set-up, trouble shooting and maintenance procedures means increased productivity for you. That s why Parker provides the most complete line of hydraulic and pneumatic diagnostic equipment available today. With Parker diagnostic equipment you can take critical measurements from your system with just a push of a button. Parker diagnostic instruments are designed to identify hard-to detect variations and peaks in pressures, temperatures and flow. Parker diagnostic quick couplings and nipples allow quick and easy access into hydraulic or pneumatic systems at remote test points without the use of tools. iagnostic nipples can be permanently installed in threaded test ports in hydraulic components such as valves, cylinders, accumulators, filters or pumps. iagnostic tube ends, used in conjunction with a 37 flare, bite type, or O-ring face seal tube fitting, will allow you to take pressure readings in your systems tubing and hose lines where threaded test ports may not currently be available. From diagnostic nipples to digital monitoring equipment, Parker can provide the tools necessary to increase your productivity through reduced machine downtime. F-2

158 iagnostic Products Table of ontents Introduction...F-2 Table of ontents...f-3 Product Selection Guide...F-4 The ServiceJunior...F-5 The Sensoontrol Serviceman General...F-6 Schematic...F-7 Technical ata...f-8 Test Meter Kits...F-9 omponents and ccessories...f-14 - F-17 The Sensoontrol Service Master General...F-10 Schematic...F-11 Technical ata...f-12 Test Meter Kits... F-13 omponents and ccessories...f-14 - F-17 Sensoontrol Pressure Transducers... F-15 Test Port ouplings P Series...F-18 - F-20 ust ap...f-18 ouplers...f-19 Nipples...F-19 - F-20 Tube End Nipples...F-20 PP Series...F-21 - F-22 ust ap...f-21 ouplers...f-21 Nipples...F-22 EM3 Series...F-23 Nipples...F-23 Gauge dapter & Union...F-24 Transducer dapters...f-25 Flexible Hose...F-25 PFS Series - Fluid Sampling...F-26 ouplers...f-26 Nipples...F-26 Ordering Information...F-27 Sensoontrol Flow Sensors...F-16 F iagnostic F-3

159 iagnostic Products Product Selection Guide Meter Selection Guide The Parker The Parker The Parker Function ServiceJunior Serviceman Service Master 450 Pressure Sensing Flow Sensing 1 1 Temperature Sensing 1 2 Rotational Speed Sensing 1 uxiliary Sensing Pressure ifferential utomatic Sensor Recognition uto Power Off attery Monitoring attery Type (2 req d) Rechargeable Ni-MH Rechargeable Ni-ad P ompatible (Windows) 1 1 Minimum/Maximum Memory Self ontained Memory On-Line ata Transfer Text isplay (Lines) Inputs ata Points (Maximum in Memory) 250,000 Graphic L isplay Hydraulic Power alculations Volume alculations Notes: (1) dditional accessories are required to perform this function. (2) Transducers provide an ambient temperature signal, but additional temperature probes are required for more accurate temperature measurements. Test Port oupling Selection Guide F iagnostic Test Port Valving ody Material* Locking Std. Seal Temp Rated Size r SS S P Mechanism Material Range** Pressure P Series Flush Face 1/8" all Nitrile -40 to +250 F 6000 PSI PP Series all 1/8" all Nitrile -40 to +250 F 6000 PSI EM3 Series Poppet 1/8" Threads Nitrile/Fluorocarbon -15 to +250 F 9000 PSI * See Fluid ompatibility chart and/or consult factory for questions regarding proper material for specific applications. OE: r = rass; SS = Stainless Steel; S = Steel; P = Plastic **Temperature Range for standard seal material. Note: See the Specifications Table for P and PP Series for more information. F-4

160 iagnostic Products The Sensoontrol ServiceJunior Technical ata The new Parker ServiceJunior captures momentary pressure spikes that are invisible to normal liquid-filled gauges. That means the maximum pressure reading it delivers can be trusted as a much truer reflection of the system s actual condition; so you can identify potential problems better and diagnose their causes faster. ll readings are accurate to within +/-0.5%. ServiceJunior Features Easy to connect and test system pressure using Parker iagnostic test port couplings Robust, dirt resistant housing Simple to operate, four key menu Four digit backlit display with easy to read large 0.60" characters Minimum and maximum graphic display shows pressure peak Power status displayed continuously an be used with most hydraulic and pneumatic media Measure PSI, bar, mpa, kpa with one gauge ccuracy +/- 0.5% of full scale Four pressure ranges Operating temperature 14 to 122º F Fluid temperature -4 to 176º F Storage temperature -4 to 140º F uto power off after 5 minutes or "constant on" at the touch of a button Zero adjustment function 10 msec scanning rate Ratings: Environmental Protection: EN60529 (IP 65) Vibration: IE /10 500Hz: 20g Shock: IE /50g 11 msec Measuring ServiceJunior ServiceJunior ServiceJunior Overload Range with P oupler with EM3 oupler with 1/4" NPT Port Pressure Resolution to 250 PSI (-1 to 16 bar) SJR-0250-P SJR-0250-EM SJR MP 580 PSI 0.1 PSI 0 to 1500 PSI (0 to 100 bar) SJR-1500-P SJR-1500-EM SJR MP 2,900 PSI 1 PSI 0 to 5800 PSI (0 to 400 bar) SJR-5800-P SJR-5800-EM SJR MP 11,600 PSI 1 PSI 0 to 8700 PSI (0 to 600 bar) SJR-8700-P 1 SJR-8700-EM 2 SJR MP 17,400 PSI 1 PSI F iagnostic NOTES: 1. P ouplers rated to 6,000 PSI max. 2. EM3 ouplers rated to 9,000 PSI max. ccessories Part Number P240 S-7/16-EM-3 SJ-1/4 PH-19 SM3-400 S-110 S-150 escription P Series diagnostic coupler 7/16-18UNF-2 female to M16X2.0 EM3 female swivel 7/16-18UNF-2 female to 1/4" NPT male adapter 19" P Hose extension to be used with P nipple interface 16 hose assembly for EM M16X2.0 interface Storage case for one gauge and diagnostic adapters Storage case for two gauges and diagnostic adapters F-5

161 iagnostic Products The Sensoontrol Serviceman General Hand-held iagnostic Meter to Measure Pressure, Temperature, Flow and Rotational Speed for Hydraulic and Pneumatic Systems Easy operation Rugged design ompact imensions Two line display uto sensor recognition MIN/MX Memory Pressure differential External power supply ata output for P F iagnostic The Serviceman SM-152 from Parker is a portable diagnostic measuring system an excellent alternative to conventional mechanical pressure gages a very rugged, durable test meter that can withstand even the most demanding environmental conditions. The Serviceman meter uses the latest in sensor recognition technology which eliminates the need for meter adjustment. It s powered by a rechargeable Ni-MH battery system or a 120 volt external power supply for continuous operation Using Serviceman software (compatible with Windows 98 and newer operating systems) the SM-152 quickly interfaces with an Excel spread sheet. The Serviceman field kit is the ideal set of diagnostic tools for maintenance and service personnel in the industrial, mobile and agricultural markets. These units help reduce downtime by recording the best preventative maintenance and diagnostic data available. Parker Hannifin provides the most complete line of hydraulic and pneumatic diagnostic equipment available today. For more information contact the or your local distributor. F-6

162 Sensoontrol Serviceman Measure and ocument Flow, Pressure, iagnostic Temperature Products and Rotation Speed The Sensoontrol Serviceman Schematic Meter SM Meter Power Supply / Recharger SSN-450 INP1 PSI INP2 GPM ON/OFF INP1/2 RESET MX Sensoontrol SSN MIN PRINT ZERO INPT1 Serviceman SM-152 INPT2 RS232 onnector P omputer dapter Software kit SSW-KIT-152 F iagnostic able SK able SK able SK Pressure Transducer P XXXX-XXXX iagnostic Nipple Temperature Sensor Port M10 X 1 M10 x 1 Temperature Sensor ST Tachometer SRPM 220 iagnostic oupler Flow Sensor SFT-XXXX-XX dapter ST-1/4 M10 X 1 To 1/4 NPTF F-7

163 iagnostic Products The Sensoontrol Serviceman Technical ata 1 2 INP1 INP2 PSI GPM ON/OFF RESET INP1/2 MX 1-2 MIN PRINT ZERO Serviceman SM-152 INPT1 INPT2 Function escriptions 1 Two Line Measurement isplay 2 RESET resets minimum and maximum values to zero 3 ON/OFF Switch 4 MX displays maximum value since meter was last reset or turned on 5 INP1/2 selects whether meter will display measurement from Input 1 or Input 2 6 l1-l2 displays the differential value of Input 1 minus Input 2 7 MIN displays minimum value since meter was last reset or turned on 8 PRINT sends displayed measurements to P or printer 9 HOL resets display to zero 10 Two Inputs (5 pin) 11 External Power Supply Socket 12 ata Output via RS232 interface to transmit measured values to P Serviceman Technical ata F iagnostic Meter 2 Line isplay Shows oth Inputs 4 igit L Text isplay isplay of Pressure, Temperature, Flow and Rotational Speed - Pressure in PSI and ar - Temperature in F and - Flow in GPM and l/min. - Rotational Speed in RPM Housing S Plastic Housing Protective Rubber over arrying Strap Integral Stand Inputs Two 5-pin push-pull Inputs 0-3 Volts (R=470 kω) 12 it / onverter utomatic Sensor Recognition 2 ms Scanning Rate mbient onditions Operating Temperatures 32 F to 122 F (0 to 50 ) Storage Temperatures -4 F to 140 F (-20 to 60 ) Output RS232 Interface to transfer measured values to a P. The SSW-KIT-152 software and adapter kit is required for data transfer to a P. Power Requirements 9 Volt Rechargeable Ni-MH attery Recharge circuit for use with external power supply. 5 Hour attery Life F-8

164 iagnostic Products The Sensoontrol Serviceman Test Meter Kits Test Meter Kits Kit ontents: ase s-150 Serviceman Meter SM Transducers (Quantity 1 or 2) (See elow) able (Quantity 1 or 2) SK Power Supply Meter* SSN-450 Instruction Manual* SM-152-TM * Included with Serviceman Meter ode for Ordering Serviceman Meter Kits: PS3 - X - XX - XX iagnostic Style Transducer Pressure Range (hoose one or two) OE ESRIPTION 2 P Style 4 PP Style 6 EM3 Style (Female) OE PRESSURE OLOR PSI lue PSI Green PSI Yellow PSI Orange PSI Red dditional Transducers ode for Ordering Separately: P XXXXXX - XXXX Flow Sensors iagnostic Style ode for Ordering Separately: SFT-XXXX - XXX iagnostic Style Flow Range Pressure Range OE T PT TEM3 ESRIPTION P Style PP Style EM3 Style (Female) OE FLOW RTE GPM (1 15 l/min) GPM (4 60 l/min) GPM ( l/min) GPM ( l/min) OE PRESSURE OLOR PSI lue PSI Green PSI Yellow PSI Orange PSI Red OE ESRIPTION P P Style PP PP Style EM EM Style F iagnostic F-9

165 iagnostic Products The Sensoontrol Service Master General Hand-held iagnostic Meter to Measure Pressure, Temperature, Flow and Rotational Speed for Hydraulic and Pneumatic Systems Easy operation Rugged design Large display uto sensor recognition MIN/MX Memory On-line operation Multiple sensor inputs attery monitoring F iagnostic The Parker Service Master meter is a state-of-the-art instrument with six channels for data collection. The ergonomically designed case and large automatic scaling L display make it very easy to use in even the most demanding environments. They are the perfect tool to capture diagnostic measurements at remote locations. ble to measure pressure, temperature, flow and rotational speed simultaneously, the data can be gathered and stored on a P for later analysis. The SM-450 provides 250,000 data points of storage. These measurements can easily be transferred to your P via an RS232 interface and SensoWin 4.03 software which is compatible with Windows98 and newer operating systems. s with all Sensoontrol equipment, the Parker Service Master offers the latest in sensor recognition technology, eliminating the need for individual sensor setup. It also allows you to program the individual inputs to accept other data collection formats, such as 4-20 ma, or 0-10 Volt. Parker Hannifin provides the most complete line of hydraulic and pneumatic diagnostic equipment available today. For more information contact the Quick oupling Ivision or your local distributor. F-10

166 iagnostic Products The Sensoontrol Service Master Schematic The Sensoontrol Service Master Measure and ocument Flow, Pressure, Voltage, urrent, Temperature and Rotation Speed Meter SM The Service Master ON/OFF SETUP OPTION Meter Power Supply / Recharger SSN-450 T OUTPUT REOR STOP STRT ES ENTER = 2 TEMP MIN/MX TUL RESET Sensoontrol SSN-450 able SK onnect To Serial Port On P With SSW-400 Software able SK able SK able SK F iagnostic Pressure Transducer P XXXX-XXXX iagnostic Nipple Temperature Sensor Port M10 X 1 M10 x 1 Temperature Sensor ST Tachometer SRPM 220 iagnostic oupler Flow Sensor SFT-XXXX-XX dapter ST-1/4 M10 X 1 To 1/4 NPTF F-11

167 iagnostic Products The Sensoontrol Service Master Technical ata Function escriptions The Service Master ON/OFF SETUP OPTION T REOR OUTPUT STOP STRT ES ENTER 1-2 TEMP 1 = 2 MIN/MX TUL RESET ON/OFF Turns meter on or off 2 SETUP/OPTION hange system settings 3/4 RROWS Select line and function values 5 STRT/ENTER hange function values and start measurements 6 STOP/ES Stop or terminate functions 7 I1-I2 ifferential value between input 1 and input 2. 8 TEMP isplays the measured temperature values for all channels 9 T-OUTPUT isplays output to P, printer or graphic display 10 REOR To record and store measurements 11 MIN/MX/TUL isplays the minimum, maximum and actual values. Reset deletes values 12 INPUTS Inputs for up to (6) sensors V Input for external power supply and charging of internal battery 14 T OUTPUT RS232 port for connecting to the P, printer, or external trigger module 15 GRPHI L isplays measured values, adjustment menus and graphics. 16 ITIONL LINE isplays the power or flow runout values. 17 STTUS LINE Shows the designation of the measured value or the menu name. Technical ata F iagnostic Meter igital L Text isplay - 128x64 pixels utomatic haracter Height Scaling isplay of Pressure, Temperature, Flow and Rotational Speed - Pressure in PSI and ar - Temperature in F and - Flow in GPM and l/min. - Rotational Speed in RPM Inputs Six, 5-pin push-pull style connectors utomatic Sensor Recognition 0-3 Volts (R=470 kω) 12 it / onverter 1 ms Scanning Rate (1-3 inputs) 2 ms Scanning Rate (4-6 inputs) Functions ifferential Value Measurement MIN/MX Memory Online data transfer attery level indicator Power calculation (display only) Flow run-out (display only) uto power off Output RS232 interface djustable baud rate up to PS 8 data bits, 1 stop bit Power Requirements Internal 7.2-volt rechargeable Ni-ad battery Recharge circuit for use with external power supply. Operating time (prox. 5 hours) Excitation voltage (12-30 V) Memory Functions Memory capacity 250,000 data points Memory used in 25,000 data point intervals Variable storage rate Variable measuring period up to 100 hours Manual and automatic triggering mbient onditions Operating Temperatures 32 F to 122 F (0 to 50 ) Storage Temperatures -4 F to 140 F (-20 to 60 ) Protection class IP54 Housing Glass reinforced polyamide 11-Key tactile touch membrane EM Protection - Electromagnetic interference (IN/EN 50081, Part 1) - Immunity to emitted interference (IN/EN 50082, Part 2) imensions Length/Height/Width x 4.19 x (235 x 106 x 52 mm) Weight 1.2 lbs (700 grams) F-12

168 iagnostic Products The Sensoontrol Service Master Test Meter Kits Test Meter Kits Kit ontents: ase The Parker Service Master Meter Transducers (Quantity 2) Transducer able, 10 (Quantity 2) Power Supply Meter* SensoWin Software 4.03 omputer Interface able Operating Manual* * Included with the Parker Service Master Meter ode for Ordering the Parker Service Master Meter Kits: PSM 45 - X - XX - XX iagnostic Style The Parker Service Master 450 Meter Kit S-690 SM (See elow) SK SSN-450 SSW-400 SK Transducer Pressure Range (hoose two) OE ESRIPTION 2 P Style 4 PP Style 6 EM3 Style (Female) OE PRESSURE OLOR PSI lue PSI Green PSI Yellow PSI Orange PSI Red Meter Style OE ESRIPTION 45 The Parker Service Master 450 Meter dditional Transducers ode for Ordering Separately: P XXXXXX - XXXX iagnostic Style Pressure Range OE T PT TEM3 ESRIPTION P Style PP Style EM3 Style (Female) OE PRESSURE OLOR PSI lue PSI Green PSI Yellow PSI Orange PSI Red F iagnostic Flow Sensors ode for Ordering Separately: SFT-XXXX - XXX iagnostic Style Flow Range OE FLOW RTE GPM (1 15 l/min) GPM (4 60 l/min) GPM ( l/min) GPM ( l/min) OE ESRIPTION P P Style PP PP Style EM EM Style F-13

169 iagnostic Products The Sensoontrol Serviceman /Service Master omponents and ccessories Overview hart F iagnostic The Parker The Parker escription Serviceman Service Master Part Number Serviceman Hand-held meter, 2 inputs (Includes SSN-450 Power Supply) SM The Parker Service Master Hand-held meter, 6 inputs, 250,000 data points (Includes SSN-450 Power Supply) SM Storage ase S-150 Storage ase S-690 Power Supply 120 Volt SSN-450 onnection able Used between meter and sensors (3m length) SK Extension able Used in series with connection cables (5m length) SK Pressure Transducers Five measurement ranges See page F-15 Flow Sensors Four measurement ranges See page F-16 Temperature Sensor Used with Parker Flow Sensors or ST-1/4 Port dapter (Requires standard connection cable) ST Port dapter onverts M10X1 to 1/4 male NPT thread ST-1/4 Tachometer To measure rotational speed (0 to 10,000 RPM) SRPM-220 ontact dapter For SRPM-220 Tachometer SRPM-001 Focus dapter For SRPM-220 Tachometer SRPM-002 iagnostic Test Hose ssembly Used with P style Parker Transducers and diagnostic nipples PH-19 Voltage dapter Used with auxiliary sensors SM-V-250 ata able and Software To connect the Serviceman meter to a P SSW-KIT-152 SensoWin 4.03 Software For data transfer from the Parker Service Master meter to a P SSW-400 ata able Used between the Parker Service Master meter and a P SK F iagnostic F-14

170 iagnostic Products The Sensoontrol Serviceman /Service Master omponents and ccessories Transducers Pressure Transducer Options Six measurement ranges: Vacuum to 14,500 PSI olor coded for easy identification orrosion resistant stainless steel housing ccuracy of.5% Full Scale (FS) vailable with P, PP or EM style diagnostic couplings Transducer Technical ata P P P P P Measuring Range (Pressure) to 235 PSI 0 to 870 PSI 0 to 2175 PSI 0 to 5800 PSI 0 to 8700 (1) PSI olor ode lue Green Yellow Orange Red Measuring Range (Temp.) -13 F to 221 F -13 F to 221 F -13 F to 221 F -13 F to 221 F -13 F to 221 F Max. Overload Pressure 290 PSI 1450 PSI 3625 PSI PSI PSI Output Signal (Volts) -0.2 to 2 0 to 3 0 to 3 0 to 3 0 to 3 Hysteresis (% FS Typical) Repeatability (%FS Typical) Non-conformity (%FS) Response Time 1 ms 1 ms 1 ms 1 ms 1 ms Excitation Voltage 7-12 V 7-12 V 7-12 V 7-12 V 7-12 V (1) Maximum Rated Pressure for P Series ouplers is 6000 PSI. (2) Maximum Rated Pressure for EM Series ouplers is 9000 PSI. in the Part Number Represents: T = P Style PT = PP Style TEM3 = EM3 Style (Female) Materials of onstruction Transducer Stainless steel iaphragm stainless steel oupler..hromium-6 Free Plated steel Seal Fluorocarbon Temperature Range Working to 185 Fluid to 221 Storage to 257 Output ccuracy % FS Load m ohms Response time <1 ms Output signal to noise %fs Resonant frequency KHz Voltage Requirement 7 to 12 V excitation voltage Permissible ripple ±2% ss urrent requirement m able End (Pin Out) Pin Mark Wire olors 1 P yellow 2 T white 3 + brown 4 green 5 SK grey F iagnostic Special Note: ll Parker Sensoontrol hand-held diagnostic meters are now equipped with the same 5-pin push-pull style connector ports. ccessories such as pressure sensors, temperature sensors, flow meters, tachometers and cables are all interchangeable between Serviceman and the Parker Service Master meters. F-15

171 iagnostic Products The Sensoontrol Serviceman /Service Master omponents and ccessories Flow Sensors These flow sensors are a compact light-weight aluminum diagnostic tool capable of measuring pressure, temperature and flow from a single test point in a hydraulic system. These flow sensors are designed to be used with a wide variety of hydraulic fluids. This design also minimizes the effect of viscosity changes. These units are manufactured from solid aluminum bar stock and are rated to 6000 PSI* and temperatures of 0 F to +350 F. They are available in four sizes with flow measuring ranges from GPM. Flow sensors are provided with a choice of P, PP or EM style diagnostic ports and are designed to be used with Serviceman and the Parker Service Master equipment. Flow Sensors Technical ata Pressure Rating* PSI * SFT 7160 is rated to 5000 PSI Fluid Temperature Range F to +350 F mbient Temperature Range F to +120 F Media/ompatibility Petroleum ased Fluids (ontact factory for use with water based hydraulic fluids) Flow Measurement ccuracy ±1.0% ctual Reading Voltage Input to 12 V (Supplied by Sensoontrol meter) urrent Requirement m Response Time ms Viscosity Range to 50 cst Material Specifications Flow lock nodized luminum Turbine Stainless Steel earings stainless Steel Seal Material Nitrile Electrical onnection Pin Push-Pull Style F iagnostic How to Order Measuring Flow Sensor Flow Sensor Flow Sensor Inlet/Outlet Port Length Height Width Range with P Nipple with PP Nipple with EM Nipple onfiguration inches inches inches GPM (1 15 l/min) SFT-0004-P SFT-0004-PP SFT-0004-EM 3/4-16 OR GPM (4 60 l/min) SFT-0116-P SFT-0116-PP SFT-0116-EM 1 1/16-12 OR GPM ( l/min) SFT-0380-P SFT-0380-PP SFT-0380-EM 1 5/16-12 OR GPM ( l/min) SFT-5160-P SFT-5160-PP SFT-5160-EM 1 5/8-12 OR F-16

172 iagnostic Products The Sensoontrol Serviceman /Service Master omponents and ccessories Special Note ll Parker Sensoontrol hand-held diagnostic meters are now equipped with the same 5-pin push-pull style connector ports. This means accessories such as pressure sensors, temperature sensors, flow meters, tachometers and cables are all interchangeable between the Serviceman and the Parker Service Master meters. Temperature Sensor for Serviceman and the Parker Service Master. an be used with Parker flow sensors or with an ST-1/4 port adapter. ccuracy: + 1.5% Full scale Temperature range: -13 F to 257 F (-25 to 125 ) Part Number ST SRPM Tachometer for Serviceman and the Parker Service Master Meters. isplays a precision measurement of rotational speed. 5-pin push-pull style connector. Part Number SRPM-220 Technical ata Measuring Range ,000 RPM Measuring istance in ccuracy % FS Excitation Voltage V Output Signal V Resolution RPM Tachometer dapters ontact dapter for belt drive/wheel. Part Number SRPM-001 Focus dapter for confined areas. Part Number SRPM-001 Voltage dapter for use with uxiliary Sensors to the Parker Service Master. Input: 0-20 M or 0-10 V ccuracy: 0.25% FS Part Number SM-V pin to 5 pin ables Flow sensor, transducer and temperature probe cables for both Serviceman and the Parker Service Master. Length Part Number 10 ft (3 m) SK Extension able 16.4 ft (5 m) SK SensoWIN 4.03 Software for data transfer from the Parker Service Master Meter to a P (Windows 98 and newer). Part Number SSW-400 F iagnostic ata able/software for use between the Serviceman Meter and a P (Windows 98 and newer). Part Number SSW-KIT-152 F-17

173 iagnostic Products Test Port ouplings P Series pplications P Series couplings provide easy connection for mechanical gauges or specialized diagnostic equipment like Sensoontrol. Typically, P or P nipples are permanently mounted in the system at threaded test ports, in rigid tubing or in hose assemblies. P couplers are attached to test instruments. ouplers align to the mating nipples without threading. This allows gauges, transducers and other test equipment to be snapped into place without difficulty. Note: Protective dust plugs and caps play a crucial role in the life of a quick coupling and no purchase of a hydraulic quick coupling is complete without the selection of an appropriate dust plug and cap. See pages noted in Table of ontents for dust plugs and caps for the Parker full line of hydraulic couplings. F iagnostic Features Flush-face poppet valves minimize air inclusion and spillage, provide easy-to-clean surfaces, and help to prevent contamination. Grip-tight knurled sleeves help to make connecting and disconnecting easy, even while wearing gloves. Nipples are machined from high tensile steel for strength to withstand 6000 PSI continuous operating pressure. P nipples offer features similar to the standard steel P nipples with the added feature of a brass body. P nipples are designed to meet or exceed SE J1502 and ISO design and performance specifications. End connections include pipe, O-ring, metric thread, bulkhead, 37 Flare, ORFS and bite-type. Specifications Ordering information oupler/nipple Material Prefix for rass body Prefix SS for Stainless Steel body Standard body material is Steel ody Size 1/8 escription P oupler P Nipple P Nipple ssembly Part Number P242 P361 P343Y ody Material (Steel) arbon Steel High Tensile rass Steel Rated Pressure (PSI) Temperature Range (ST Seals) Nitrile -40 F to +250 F -15 F to +400 F -40 F to +250 F (Fluorocarbon) Rated Flow (GPM) 0.8 Max. Recommended Flow (GPM) 4.0 urst Pressure (PSI/Min) 23,000 40,000 17,000 Vacuum ata (Inches Hg) Pressure rop at Rated Flow (PSI) with 200 SUS Fluid 56 Spillage at 15 PSI (ml)-ssembly 0.1 per disconnect ir Inclusion (ml)-ssembly 0.02 per connect onnect Force-ssembly 41 Lbs. (100 PSI) isconnect Force-ssembly 20 Lbs. (100 PSI) Optional Seals Suffix* No suffix is required when ordering products with the standard Nitrile seals. When specifying an optional seal, refer to the following chart to determine the appropriate suffix.** oupling Series Ethylene Fluoro- Neoprene Perfluoro- Propylene carbon elastomer P Series W Y Z PP Series W Y Z *To select proper seal materials, see Fluid ompatibility hart in ppendices section, or contact your Parker Quick oupling istributor. **N/ = Not vailable; ST = Standard (No Suffix Needed) P Series UST P ody Size ust ap (in.) Part No. 1/8 P6-285 F-18

174 iagnostic Products Test Port ouplings P Series ouplers Female Thread ody Female Female imensions (in.) Size Part Thread Thread Overall Wrench Largest Wt. (L.) (in.) No. NPTF OR Length Flats iameter P/Piece 1/8 P222 1/ /8 P240 7/ /8 P242 1/ /8 SSP242Y** 1/ /8 P260 9/ Male Thread ody Male Male imensions (in.) Size Part Thread Thread Overall Wrench Largest Wt. (L.) (in.) No. NPTF OR Length Flats iameter P/Piece 1/8 P243 1/ Nipples Female Pipe Thread E G ody Thread imensions (in.) Size Part Size Overall Exposed Hex Largest Wt. (L.) (in.) No. NPTF Length Length Size iameter P/Piece E F G 1/8 P322 1/ /8 P342 1/ Male Pipe Thread F E F G ody Thread imensions (in.) Size Part Size Overall Exposed Hex Largest Wt. (L.) (in.) No. NPTF Length Length Size iameter P/Piece E F G 1/8 P323 1/ /8 P323Y* 1/ /8 P343Y* 1/ /8 P343 1/ /8 SSP343Y** 1/ /8 P363 3/ Metric Thread F E G ody Thread imensions (in.) Size Part Size Overall Exposed Hex Largest Wt. (L.) (in.s) No. Metric Length Length Size iameter P/Piece E F G 1/8 P357 M10 x /8 P3107 M16 x /8 P3127 M18 x /8 P3147 M20 x F iagnostic Male Straight Thread F E G ody Thread imensions (in.) Size Part* Size Overall Exposed Hex Largest Wt. (L.) (in.) No. OR Length Length Size iameter P/Piece E F G 1/8 P331 3/ /8 P341 7/ /8 P351 1/ /8 P361 9/ * Note: dd -6 to part number to include dust cap, for example P343-6 * P designates brass body, Fluorocarbon seal standard ** SSP designates 316SS body, Fluorocarbon seal standard F-19

175 iagnostic Products Test Port ouplings P Series Nipples ulkhead Triple-Lok F E G ody Part imensions (in.) Size No. Thread Tube Overall Exposed Hex Largest Wt. (L.) (in.) Steel Size Size Length Length Size iameter P/Piece E F G 1/8 P345 7/ / /8 P355 1/2-20 5/ /8 P365 9/ / ulkhead Seal-Lok F E G ody Part imensions (in.) Size No. Thread Tube Overall Exposed Hex Largest Wt. (L.) (in.) Steel Size Size Length Length Size iameter P/Piece E F G 1/8 P346 9/ / /8 P366 11/ / /8 P386 13/ / Tube End Nipples* Triple-Lok P TX ody Part imensions (in.) Size No. Tube Overall Exposed Wt. (L.) (in.) Steel Size Length Length P/Piece 1/8 P34TX 1/ /8 P36TX 3/ /8 P38TX 1/ /8 P312TX 3/ * Tube end nipples are designed to meet the performance standards of the tube or hose fitting connection, which may or may not meet SE J1502 Standards. Seal-Lok P TL F iagnostic ody Part imensions (in.) Size No. Tube Overall Exposed Wt. (L.) (in.) Steel Size Length Length P/Piece 1/8 P34TL 1/ /8 P36TL 3/ /8 P38TL 1/ /8 P310TL 5/ * Tube end nipples are designed to meet the performance standards of the tube or hose fitting connection, which may or may not meet SE J1502 Standards. Note: dd -6 to part number to include dust cap, for example P343-6 F-20

176 iagnostic Products Test Port ouplings PP Series Features Made to connect under pressure up to 6000 psi Grip-tight knurled sleeves help to make connecting and disconnecting easy, even while wearing gloves. Nipples are machined from high tensile steel for strength to withstand 6000 PSI continuous operating pressure. End connections include pipe, O-ring, 37º Flare and ORFS urable all Valve Nipple. oupler is unvalved to allow gauges and transducers to return to zero when disconnected. Specifications ody Size 1/8 escription PP oupler PP Nipple ssembly ody Material (Steel) arbon High Tensile Steel Steel Rated Pressure (PSI) Temperature Range (ST Seals) Nitrile -40 F to +250 F onnect Force-ssembly 6 Lbs (0 PSI PSI) isconnect Force-ssembly 7 Lbs (0 PSI PSI) oupler (connect-under-pressure) Female Thread pplications The PP Series couplings provide easy connection for mechanical gauges or specialized diagnostic equipment like Sensoontrol. Typically, PP nipples are permanently mounted in the system at threaded test ports, in rigid tubing or in hose assemblies. PP couplers are attached to test instruments. Locking balls align the couplers to the mating nipples without threading, so gauges, transducers and other test equipment can be snapped into place without difficulty. Parker's PP Series couplings offer the advantages of P couplings, but are designed to connect easily and quickly under full system pressure up to 6000 PSI (operating). PP couplers and nipples push to connect with a constant force of only six pounds. Then the coupler base is turned to open the valve and complete the connection. In the connected position, the coupler base blocks the retracting sleeve to prevent accidental disconnects. Ordering information oupler/nipple Material Standard body material is steel. Optional Seals Suffix* No suffix is required when ordering products with the standard Nitrile seals. When specifying an optional seal, refer to the following chart to determine the appropriate suffix.** oupling Series Ethylene Fluoro- Neoprene Perfluoro- Propylene carbon elastomer P Series W Y Z PP Series W Y Z *To select proper seal materials, see Fluid ompatibility hart in ppendices section, or contact your Parker Quick oupling istributor. **N/ = Not vailable; ST = Standard (No Suffix Needed) ody Part Thread imensions (in.) Size No. Size Overall Wrench Largest Wt. (L.) (in.) Steel NPTF Length Flats iameter P/Piece 1/8 PP242 1/ F iagnostic PP Series UST P ody Size ust ap (in.) Part No. 1/8 P6-285 F-21

177 iagnostic Products Test Port ouplings PP Series Nipples* (connect-under-pressure) Male Pipe E ody Part Thread imensions (in.) Size No. Size Overall Exposed Hex Largest Wt. (L.) (in.) Steel NPTF Length Length Size iameter P/Piece E F G 1/8 PP323 1/ /8 PP343 1/ G F Straight Thread ody Part Thread imensions (in.) Size No. Size Overall Exposed Hex Largest Wt. (L.) (in.) Steel OR Length Length Size iameter P/Piece E G E F G 1/8 PP341 7/ /8 PP361 9/ *dd -6 to part number to include dust cap. F Triple-Lok E ody Part imensions (in.) Size No. Tube Overall Exposed Hex Largest Wt. (L.) (in.) Steel Size Length Length Size iameter P/Piece E F G 1/8 PP34TX 1/ /8 PP36TX 3/ G F iagnostic Seal-Lok F E ody Part imensions (in.) Size No. Tube Overall Exposed Hex Largest Wt. (L.) (in.) Steel Size Length Length Size iameter P/Piece E F G 1/8 PP34TL 1/ /8 PP36TL 3/ G F F-22

178 iagnostic Products Test Port ouplings EM3 Series pplications Features Knurled sleeve allows simple twist-to-connect operation without the use of tools Rugged design allows connect-under-pressure operation up to 5800 psi Maximum rated working pressure of 9000 psi exceeds the requirements of most applications Integral threaded dust cap protects the test point from damage and contamination EM fittings are machined from solid barstock and protected with hromium-6 Free plating. Stainless steel springs for corrosion resistance Elastomeric interface and valve seals provide leak free operation ompact design and optional high pressure hose assemblies provide flexibility for tight space requirements EM couplings provide easy diagnostic connections for Parker Sensoontrol equipment or mechanical gages. EM test points are typically permanently plumbed into a fluid system at locations where pressure measurements are required for maintenance or testing. Integral pressure cap protects the test point from damage and prevents contamination of the fluid system. Proven twist-to-connect design allows the test points to be connected even when the system is in operation and the test points are pressurized. EM s compact design and optional high pressure hose assemblies allow extra flexibility for the location of system test points. lthough designed primarily for diagnostic applications, EM fittings and hose assemblies are idea for a wide range of applications that require compact high pressure connections and limited flow rates. Specifications ody Size 1/8 Rated Pressure (PSI) 9000 PSI Max onnect-under-pressure (PSI) 5800 Rated Flow (GPM) 0.8 ody Material hromium-6 Free Plated Steel Seal Material (std.) Nitrile/Fluorocarbon Temperature Range (std. seals) -15 to +250 F Male Pipe Thread Port Hex Interface Part Thread Size Thread Overall Wt. (L.) No. Size (mm) Size Length P/Piece EM3/1/8NPT 1/8-27NPT 17 M16X EM3/1/4NPT 1/4-18NPT 17 M16X EM3/1/4NPT71 1/4-18NPT 17 M16X Stainless Steel SE Straight Thread Metric Straight Thread Port Hex Interface Part Thread Size Thread Overall Wt. (L.) No. Size (mm) size Length P/Piece EM3/7/16-20UNF-2* 7/16-20UNF-2 17 M16X EM3/9/16-18UNF-2* 9/16-18UNF-2 19 M16X * O-Ring seal on port Port Hex Interface Part Thread Size Thread Overall Wt. (L.) No. Size (mm) Size Length P/Piece EM3/M8X1OR* M8X1 17 M16X EM3/10X1E** M10X1 17 M16X EM3/12X1.5E** M12X M16X EM3/14X1.5E** M14X M16X F iagnostic ritish Parallel Pipe * O-Ring seal on port ** Molded seal on port Port Hex Interface Part Thread Size Thread Overall Wt. (L.) No. Size (mm) Size Length P/Piece EM3/1/8E** 1/8 SPP 19 M16X EM3/1/4E** 1/4 SPP 19 M16X EM3/3/8E** 3/8 SPP 21 M16X ** Molded seal on port F-23

179 iagnostic Products Test Port ouplings EM3 Series EM Gauge dapter Port Hex Port Part Thread Size Thread Overall Wt. (L.) No. Size (mm) Size Length P/Piece MV1/4NPT-M3 1/4-18NPT 19 M16X MV1/4NPT-M3-KM 1/4-18NPT 19 M16X Includes ust ap Port Hex Port Part Thread Size Thread Overall Wt. (L.) No. Size (mm) Size Length P/Piece MVM1/4NPT-M3 1/4-18NPT 19 M16X Union Port Hex Port Part Thread Size Thread Overall Wt. (L.) No. Size (mm) Size Length P/Piece EM3VS M16X M16X F iagnostic F-24

180 iagnostic Products Test Port ouplings Transducer dapters Transducer dapters 1/2-14SPP Thread* Port Interface Part Overall Hex Largest Thread Thread Wt. (L.) No. Length Size iameter Size Size P/Piece E P /2-14SPP 0.35 Port Interface Part Overall Hex Largest Thread Thread Wt. (L.) No. Length Size iameter Size Size P/Piece E PP /2-14SPP 0.35 E Hex Port Interface Part Overall Size Largest Thread Thread Wt. (L.) No. Length Metric iameter Size Size P/Piece E S-1/2-EM mm 1/2-14SPP M16X * Note: For old style M22X1.5 thread contact the division Flexible Hose Length Length Thread Size Part No. (in.) (mm) SM M16x2.0 LENGTH SM M16x2.0 SM M16x2.0 SM M16x2.0 SM M16x2.0 Note: Other lengths available upon request. Maximum pressure rating for test hose is 9000 psi. F iagnostic F-25

181 iagnostic Products Test Port ouplings Fluid Sampling Features These diagnostic fluid sampling products are designed to provide an easy access point for obtaining fluid samples. permanently mounted test point eliminates the need to shut down or break lines when taking samples and reduces the chances of contamination. Fluid analysis is crucial in both engines and hydraulic systems as it can reveal problems with filtration and other internal components. Early detection can prevent costly repairs, unscheduled maintenance and production downtime. These fluid sampling nipples should be installed in either low pressure or return lines. For the most accurate monitoring, fluid samples should be constantly taken from the same location. Specifications ody Size (in.) 1/8 Rated Pressure (psi) 500 Temperature Range (std seals: Fluorocarbon) -40 to +250 F Seal material Fluorocarbon ouplers Female Thread ody Female Female imensions (in.) Size Part Thread Thread Overall Wrench Largest Wt. (L.) (in.) No. NPTF OR Length Flats iameter P/Piece 1/8 PFS242 1/ Nipples F iagnostic Male Straight Thread Male Pipe Thread E F E F G G ody Thread Thread imensions (in.) Size Part Size Size Overall Exposed Hex Largest Wt. (L.) (in.) No. OR or NPTF METRI Length Length Size iameter P/Piece E F G 1/8 PFS341 7/16-20 OR /8 PFS343 1/4-18 NPTF /8 PFS-PROE* N Fluorocarbon seal is standard. ust ap P6-285 is recommended. F-26

182 iagnostic Products Ordering Information When ordering Parker coupler bodies and nipples, please state the part number of each type of coupler body and each type of nipple desired. List coupler bodies and nipples as separate items rather than in combinations. e sure to double check thread or hose sizes of items required. Many of Parker s coupling products are available with unique non-standard options well suited to very specific applications. Examples of unusual end use applications might include: high temperatures (above 250 F), extremely caustic/corrosive solutions passing through the coupling, external/environmental corrosion situations, or other high wear and tear situations such as dragging the product along the ground. Please see the Fluid ompatibility hart at the end of the catalog for a guide in selecting material for various media. It is always recommended that the Quick oupling ivision be contacted with any questions concerning specific product application needs. Typically, a prefix or suffix is added to the base part number to specify a non-standard O-ring seal, or special option. The Optional Seals Suffix chart illustrates the designations. Please Note: ertain couplings series have additional "Special Order Information" which should be referred to in ordering those products. If applicable to the product, "Special Order Information" is found next to the Features and Specifications charts. oupler/nipple Material Prefix for rass body Prefix SS for Stainless Steel body Standard body material is Steel Optional Seals Suffix* No suffix is required when ordering products with the standard Nitrile seals. When specifying an optional seal, refer to the following chart to determine the appropriate suffix.** oupling Series Ethylene Fluoro- Neoprene Perfluoro- Propylene carbon elastomer P Series W Y Z PP Series W Y Z *To select proper seal materials, see Fluid ompatibility hart in ppendices section, or contact your Parker Quick oupling istributor. **N/ = Not vailable; ST = Standard (No Suffix Needed) iagnostic Products Test Port oupling-selection Guide Test Port Valving ody Material* Locking Std. Seal Temp Rated Size r SS S P Mechanism Material Range** Pressure P Series Flush Face 1/8" all Nitrile -40 to +250 F 6000 PSI PP Series all 1/8" all Nitrile -40 to +250 F 6000 PSI EM3 Series Poppet 1/8" Threads Nitrile/Fluorocarbon -15 to +250 F 9000 PSI F iagnostic * See Fluid ompatibility chart and/or consult factory for questions regarding proper material for specific applications. OE: r = rass; SS = Stainless Steel; S = Steel; P = Plastic **Temperature Range for standard seal material. Note: See the Specifications Table for P and PP Series for more information. Sensoontrol diagnostic product s technical information subject to change. F-27

183 ppendices ppendices 1 Parker Hannifin orporation Minneapolis, MN 55427

184 ppendices Fluid ompatibility hart odes The following seal compound and body material compatibility chart is provided as an aid in selecting a specific synthetic rubber compound or body material for a particular application. Operating and environmental conditions must be considered when making the selection of a quick coupling. Refer to the appropriate section of the catalog for Ordering Information for Seal odes for specific products. To indicate a special material just add the appropriate code letter as a suffix to the catalog number of the coupler. It is not necessary to use the code ST as the standard Nitrile seal will be used when another code is not used. For recommendations for media not listed below, please contact your Parker representative or the factory. Note This chart is intended as a guide only and is not be considered as a recommendation to use Parker quick action couplings in a specific application or with a specific fluid, other factors that must be considered include but are not limited to: fluid and ambient temperature, system pressure, both operating and peak, frequency of connect and disconnect, and applicable standards or regulations. ppendices OES: 1 = Satisfactory 2 = Fair 3 = Not Recommended 4 = Insufficient ata vailable OY MTERIL SEL MTERIL MEI rass Steel 316 S.S. 303 S.S. Nitrile E.P. Fluorocarbon Neoprene 3M F ETMIE ETI I (5%) ETONE ETOPHENONE ETYL ETONE ETYL HLORIE ETYLENE IR (200 EGREES F.) IR (300 EGREES F.) IR (400 EGREES F.) LUMINUM ETTE LUMINUM ROMIE LUMINUM HLORIE (10%) LUMINUM HLORIE (100%) LUMINUM FLOURIE LUMINUM NITRTE LUMINUM SLTS LUMINUM SULPHTE LUMS (NH3,r,K) MMONI (NHYROUS) MMONI (OL, GS) MMONI (HOT, GS) MMONIUM RONTE MMONIUM HLORIE MMONIUM HYROXIE MMONIUM NITRTE MMONIUM PERSULFTE SOLUTION MMONIUM PHOSPHTE (MONO-, I-, TRI-SI) MMONIUM SLTS MMONIUM SULFTE MYL ORTE MYL HLORIE MYL HLORONPHTHLENE MYL NPHTHLENE NIML OIL (LR OIL) ROLOR ROLOR ROLOR I-1 Parker Hannifin orporation Minneapolis, MN 55427

185 ppendices Fluid ompatibility hart OES: 1 = Satisfactory 2 = Fair 3 = Not Recommended 4 = Insufficient ata vailable OY MTERIL SEL MTERIL MEI rass Steel 316 S.S. 303 S.S. Nitrile E.P. Fluorocarbon Neoprene ROMTI FUEL - 50% RSENI I SPHLT STM OIL, NO STM OIL, NO STM OIL, NO STM OIL, NO STM REFERENE FUEL STM REFERENE FUEL STM REFERENE FUEL UTOMOTIVE RKE FLUI RIUM HLORIE RIUM HYROXIE RIUM SLTS RIUM SULFIE EER EET SUGR LIQUORS ENZLEHYE ENZENE ENZENESULFONI I (10%) ENZINE ENZOI I ENZYL LOHOL ENZYL HLORIE LEH LIQUOR ORX OREUX MIXTURE ORI I RKE FLUI (NON-PETROLEUM) RINE (SOIUM HLORIE) ROMINE ROMINE WTER UNKER OIL UTIENE (MONOMER) UTNE UTNE (2,2, & 2,3-IMETHYL) UTNOL (UTYL LOHOL) UTTER - NIML FT UTYL UTYRTE UTYL STERTE LINE LIQUORS LIUM ETTE LIUM ISULFITE LIUM RONTE LIUM HLORIE LIUM HYROXIE LIUM HYPOHLORITE LIUM SLTS LIUM SULFIE LIHE LIQUORS NE SUGR LIQUORS RON ISULPHIE RON IOXIE RON ISULFIE RON MONOXIE RON TETRHLORIE RONI I STOR OIL ELLUGUR ELLULUE (NOW FYRQUEL) HIN WOO OIL (TUNG OIL) HLORINTE SLT RINE HLORINTE SOLVENTS HLOROENZENE HLOROUTIENE HLOROFORM ppendices I-2 Parker Hannifin orporation Minneapolis, MN 55427

186 ppendices Fluid ompatibility hart OES: 1 = Satisfactory 2 = Fair 3 = Not Recommended 4 = Insufficient ata vailable ppendices OY MTERIL SEL MTERIL MEI rass Steel 316 S.S. 303 S.S. Nitrile E.P. Fluorocarbon Neoprene HLORPHENOL OONUT OIL OPPER HLORIE OPPER SLTS OPPER SULFTE ORN OIL OTTONSEE OIL REOSOLS REOSOTE RESYLI I RUE OIL UTTING OIL ENE ENTURE LOHOL ETERGENT, WTER SOLUTION IESEL FUEL IETHYLENE GLYOL IMETHYL FORMMIE OW HEMIL H OW ORNING 200, 510, OWTHERM,E ETHNOL ETHYL HLORIE ETHYL HEXNOL ETHYLENE IHLORIE ETHYLENE GLYOL FTTY IS FREON FREON FREON FREON 134a FUEL OIL GLLI I GS, LIQUI, PROPNE (LPG) GS, NTURL GSOLINE GELTIN GLUOSE GLYERINE (GLYEROL) GLYOLS GREEN SULFTE LIQUOR GULF - FR FLUI (EMULSION) GULF - FR FLUI G GULF - FR FLUI P HELIUM HEPTNE HYRULI OIL (PETROLEUM SE) HYRULI OIL (WTER SE) HYRZINE HYROGEN GS HYROLUE ISO OTNE ISOUTYL LOHOL ISOPROPYL LOHOL ISOPROPYL ETHER JP3 N JP KEROSENE LR, NIML FT LINSEE OIL LURITING OIL SE 10, 20, 30, 40, MGNESIUM SLTS MGNESIUM SULPHTE MERURY METHNE METHNOL METHYL ROMIE I-3 Parker Hannifin orporation Minneapolis, MN 55427

187 ppendices Fluid ompatibility hart OES: 1 = Satisfactory 2 = Fair 3 = Not Recommended 4 = Insufficient ata vailable OY MTERIL SEL MTERIL MEI rass Steel 316 S.S. 303 S.S. Nitrile E.P. Fluorocarbon Neoprene METHYL HLORIE (RY) METHYL HLORIE (WET) METHYL ETHER METHYL ETHYL KETONE (MEK) MIL-F (JP-9) MIL-H MIL-H MIL-H MIL-H-8446 (MLO-8515) MIL-L-2104 & MIL-L MILK MINERL OILS MLO-7277 N MLO MOILE HF MONOMETHYL HYRZINE NPHTH (OL OR PETROLEUM) NPHTHLENE NPHTHENI I NETSFOOT OIL NIKEL, ETTE NIKEL HLORIE NIKEL SLTS NIKEL SULFTE NITROGEN NITROUS OXIE OTYL LOHOL OLIVE OIL ORTHO-IHLOROENZENE OXLI I OXYGEN ( EGREES F.) OXYGEN, OL OZONE PLMITI I PR-IHLOROENZENE PRKER O LUE PENUT OIL PENTNE (2-3-METHYL, & 2-4 IMETHYL) PERHLORI I -2N PERHLOROETHYLENE PETROLTUM PETROLEUM OIL, ELOW 250 EGREES F PHENOL PHOSPHORI I (3 MOLR) PHOSPHORI I (ONENTRTE) PHOSPHOROUS TRIHLORIE PIRI I, MOLTEN PIRI I, WTER SOLUTION PINE OIL PLTING SOLUTIONS (HROME) PLTING SOLUTIONS (OTHER) PNEUMTI SERVIE POTSSIUM ETTE POTSSIUM HLORIE POTSSIUM YNIE POTSSIUM IHROMTE POTSSIUM HYROXIE (50%) POTSSIUM NITRTE POTSSIUM SLTS POTSSIUM SULFTE PRL-HIGH TEMP. HYR. OIL PROUER GS PROPNE PROPYL ETTE PROPYL LOHOL PROPYLENE ppendices I-4 Parker Hannifin orporation Minneapolis, MN 55427

188 ppendices Fluid ompatibility hart OES: 1 = Satisfactory 2 = Fair 3 = Not Recommended 4 = Insufficient ata vailable ppendices OY MTERIL SEL MTERIL MEI rass Steel 316 S.S. 303 S.S. Nitrile E.P. Fluorocarbon Neoprene PYRUL 10E PYRUL -200, SERIES PYRUL, 3 SERIES PYROGR 42, 43, 53, 55 (PHOSPHTE ESTER) PYROGR SE WTER (SLT WTER) SHELL IRUS SILIONE GRESES SILVER NITRTE SKYROL 500, TYPE SKYROL 7000, TYPE SOP SOLUTIONS SOIUM ETTE SOIUM IRONTE (KING SO) SOIUM ISULPHTE OR ISULPHITE SOIUM ORTE SOIUM RONTE (SO SH) SOIUM HLORIE SOIUM YNIE SOIUM HYROXIE (USTI SO, LYE) SOIUM HYROXIE, 50% SOIUM METPHOSPHTE SOIUM NITRTE SOIUM PERORTE SOIUM PEROXIE SOIUM PHOSPHTES SOIUM SLTS SOIUM SULFTE SOIUM SULFIE N SULFITE SOIUM THIOSULFTE SOYEN OIL STNNOUS HLORIE (15%) STEM, ELOW 400 EGEEES F * 3 3 STOR SOLVENT SUROSE SOLUTIONS SULFUR SULFUR LIQUORS SULFUR (MOLTEN) SULFUR IOXIE (RY) SULFUR TRIOXIE (RY) SUNSFE TNNI I (10%) TR, ITUMINOUS TRTRI I TERPINEOL TERTIRY UTYL LOHOL TETRHLOROETHNE TETRHLOROETHYLENE TETRETHYL LE TETRETHYL LE (LEN) TITNIUM TETRHLORIE TOLUENE TRNSFORMER OIL TRNSMISSION FLUI (TYPE ) TRIHLOROETHNE TRIHLOROETHYLENE TRIRESYL PHOSPHTE TURINE OIL #15 (MIL-L-7808) TURPENTINE VRNISH WTER WHISKEY WINE WOO OIL XYLENE ZIN SULFTE ontact the division for special EP compound used on 60 Series couplings I-5 Parker Hannifin orporation Minneapolis, MN 55427

189 ppendices Safety Guide SFETY GUIE FOR SELETING N USING QUIK TION OUPLINGS N RELTE ESSORIES NGER: Failure or improper selection or improper use of quick action couplings or related accessories can cause death, personal injury and property damage. Possible consequences of failure or improper selection or improper use of quick action couplings or related accessories include but are not limited to: ouplings or parts thrown off at high speed. angerously whipping hose. High velocity fluid discharge. ontact with conveyed fluids that may be hot, cold, Explosion or burning of the conveyed fluid. toxic, or otherwise injurious. ontact with suddenly moving or falling objects that are Sparking or explosion while paint or flammable to be held in position or moved by the conveyed fluid. liquid spraying. efore selecting or using any Parker quick action couplings or related accessories, it is important that you read and follow the following instructions. 1.1 Scope: This safety guide provides instructions for selecting and using (including installing connecting, disconnecting, and maintaining) quick action couplings and related accessories (including caps, plugs, blow guns, and two way valves). This safety guide is a supplement to and is to be used with, the specific Parker publications for the specific quick action couplings and related accessories that are being considered for use. 1.2 Fail-Safe: Quick action couplings or the hose they are attached to can fail without warning for many reasons. esign all systems and equipment in a failsafe mode, so that failure of the quick action coupling or hose will not endanger persons or property. 1.3 istribution: Provide a copy of this safety guide to each person that is responsible for selecting or using quick action coupling products. o not select or use quick action couplings without thoroughly reading and understanding this safety guide as well as the specific Parker publications for the products considered or selected. 1.4 User Responsibility: ue to the wide variety of operating conditions and uses for quick action couplings, Parker and its distributors do not represent or warrant that any particular quick action coupling is suitable for any specific end use system. This safety guide does not analyze all technical parameters that must be considered in selecting a product. The user, through its own analysis and testing, is solely responsible for: 2.4 Size: Transmission of power by means of pressurized liquid varies with pressure and rate of flow. The size of the quick action couplings and other components of the system must be adequate to keep pressure losses to a minimum and avoid damage due to heat generation or excessive fluid velocity. 2.5 Pressurized onnect or isconnect: If connecting or disconnecting under pressure is a requirement, use only quick action couplings designed for that purpose. The rated operating pressure of a quick action coupling may not be the pressure at which it may be safely connected or disconnected. 2.6 Environment: are must be taken to ensure that quick action couplings are either compatible with or protected from the environment (that is, surrounding conditions) to which they are exposed. Environmental conditions including but not limited to ultraviolet radiation, ozone, moisture, water, salt water, chemicals, and air pollutants can cause degradation and premature failure. 2.7 Locking Means: all locking quick action couplings can unintentionally disconnect if they are dragged over obstructions on the end of a hose or if the sleeve is bumped or moved enough to cause disconnect. Sleeves designed with flanges to provide better gripping for oily or gloved hands are especially susceptible to accidental disconnect and should not be used where these conditions exist. Sleeve lock or union (threaded) sleeve designs should be considered where there is a potential for accidental uncoupling. Making the final selection of the quick action couplings. ssuring that the user s requirements are met and that the use presents no health or safety hazards. Providing all appropriate health and safety warnings on the equipment on which the quick action couplings are used. 1.5 dditional Questions: all the appropriate Parker customer service department if you have any questions or require any additional information. For the telephone numbers of the appropriate customer service department, see the Parker publication for the product being considered or used. 2.0 QUIK TION OUPLING SELETION INSTRUTIONS 2.1 Pressure: Quick action couplings selection must be made so that the published rated pressure of the coupling is equal to or greater than the maximum system pressure. Surge pressures in the system higher than the rated pressure of the coupling will shorten the quick action coupling s life. o not confuse burst pressure or other pressure values with rated pressure and do not use burst pressure or other pressure values for this purpose. 2.2 Fluid ompatibility: Quick action couplings selection must assure compatibility of the body and seal materials with the fluid media used. See the fluid compatibility chart in the Parker publication for the product being considered or used. 2.3 Temperature: e certain that fluid and ambient temperatures, both steady and transient, do not exceed the limitations of the quick action couplings. Use caution and hand protection when connecting or disconnecting quick action couplings that are heated or cooled by the media they are conducting or by their environment. 2.8 Mechanical Loads: External forces can significantly reduce quick action couplings life or cause failure. Mechanical loads which must be considered include excessive tensile or side loads, and vibration. Unusual applications may require special testing prior to quick action couplings selection. 2.9 Specifications and Standards: When selecting quick action couplings, government, industry, and Parker specifications must be reviewed and followed as applicable Vacuum: Not all quick action couplings are suitable or recommended for vacuum service. Quick action couplings used for vacuum applications must be selected to ensure that the quick actions couplings will withstand the vacuum and pressure of the system Fire Resistant Fluids: Some fire resistant fluids require seals other than the standard nitrile used in many quick action couplings Radiant Heat: Quick action couplings can be heated to destruction or loss of sealability without contact by such nearby items as hot manifolds or molten metal. The same heat source may then initiate a fire. This can occur despite the presence of cool air around the quick action couplings Welding and razing: Heating of plated parts, including quick action couplings and port adapters, above 450 F (232 ) such as during welding, brazing, or soldering may emit deadly gases and may cause coupling seal damage. ppendices II-1 Parker Hannifin orporation Minneapolis, MN 55427

190 ppendices Safety Guide 3.0 QUIK TION OUPLING INSTLLTION INSTRUTIONS 3.1 Pre-Installation Inspection: efore installing a quick action coupling, visually inspect it and check for correct style, body material, seal material, and catalog number. efore final installation, coupling halves should be connected and disconnected with a sample of the mating half with which they will be used. 3.2 Quick ction oupling Halves From Other Manufacturers: If a quick action coupling assembly is made up of one Parker half and one half from another manufacturer, the lowest pressure rating of the two halves should not be exceeded. 3.3 Fitting Installation: Use a thread sealant, lubricant, or a combination of both when assembling pipe thread joints in quick action couplings. e sure the sealant is compatible with the system fluid or gas. To avoid system contamination, use a liquid or paste type sealant rather than a tape style. Use the flats provided to hold the quick action coupling when installing fittings. o not use pipe wrenches or a vice on other parts of the coupling to hold it when installing or removing fittings as damage or loosening of threaded joints in the coupling assembly could result. o not apply excessive torque to taper pipe threads because cracking or splitting of the female component can result. 3.4 aps and Plugs: Use dust caps and plugs when quick action couplings are not coupled to exclude dirt and contamination and to protect critical surfaces from damage. 3.5 oupling Location: Locate quick action couplings where they can be reached for connect or disconnect without exposing the operator to slipping, falling, getting sprayed, or coming in contact with hot or moving parts. 3.6 Hose Whips: Use a hose whip (a short length of hose between the tool and the coupling half) instead of rigidly mounting a coupling half on hand tools or other devices. This reduces the potential for coupling damage if the tool is dropped and provides some isolation from mechanical vibration which could cause uncoupling. 4.0 QUIK TION OUPLING MINTENNE INSTRUTIONS 4.1 Even with proper selection and installation, quick action coupling life may be significantly reduced without a continuing maintenance program. Frequency should be determined by the severity of the application and risk potential. maintenance program must be established and followed by the user and must include the following as a minimum: 4.2 Visual Inspection of Quick ction ouplings: ny of the following conditions require immediate shut down and replacement of the quick action coupling: racked, damaged, or corroded quick action coupling parts. Leaks at the fitting, valve or mating seal. roken coupling mounting hardware, especially breakaway clamps. 4.3 Visual Inspection ll Other: The following items must be tightened, repaired or replaced as required: Leaking seals or port connections. Remove excess dirt buildup on the coupling locking means or on the interface area of either coupling half. lamps, guards, and shields. System fluid level, fluid type and any air entrapment. 4.4 Functional Test: Operate the system at maximum operating pressure and check for possible malfunctions and freedom from leaks. Personnel must avoid potential hazardous areas while testing and using the system. 4.5 Replacement Intervals: Specific replacement intervals must be considered based on previous service life, government or industry recommendations, or when failures could result in unacceptable downtime, damage or injury risk. See instruction 1.2 above. dditional copies of the preceding safety information can be ordered by requesting Safety Guide For Selecting and Using Quick ction ouplings and Related ccessories, Parker Publication No ontact The, Minneapolis, MN. ppendices II-2 Parker Hannifin orporation Minneapolis, MN 55427

191 ppendices lpha Numeric Index Note 1. Inclusion of part numbers in this index or elsewhere in the catalog is not necessarily an indication that they are available from stock. Only items listed in the current price list are carried in stock. Parts marked as Semi-Standard, consult factory for price and delivery. 2. atalog numbers ending in the letter W, Y, or Z are not listed in this index, as these suffixes merely designate the use of an optional seal. The item can be located in the catalog by referring to the basic number without the W, Y or Z suffix. This does not apply to SM, HP, NS, N, FF, FS, FH, T, and HO Series. Please see ordering information at the end of Section. Part No. Page Part No. Page Part No. Page Part No. Page P P P E E , , P P E E P P E E P F F P E G E G J F J P P E E G441-NL G442-SL G443-NL G444-SL H12-60L...-8 H12-60N...-8 H12-61L...-8 H12-61N...-8 H H H H H H H H H H2-60-STM...-9 H H2-61-STM...-9 H H2E...-6 H2F...-6 H2G...-6 H H H H3E...-6 H3F...-6 H H4-60-STM...-9 H H4-61-STM...-9 H5G...-7 H H6-60-STM...-9 H H6-61-STM...-9 H67E-60K...-8 H67E-61K...-8 H67F-60K...-8 H67F-61K...-8 H67G-60K...-8 H67G-61K...-8 H67J-60K...-8 H67J-61K...-8 H H8-60-STM...-9 H H8-61-STM...-9 H8P...-7 P323Y...F-19 P343Y...F-19 PFS341...F-26 PFS343...F-26 PN251F PN252F PN253F PN352F PN353F PV PV ST ST ST ST-1M ST ST-2M ST ST-3M ST ST-4M ST ST-6M ST ST-8M ST-N ST-N ST-N10M ST-N ST-N12M ST-N1M ST-N ST-N2M ST-N ST-N3M ST-N ST-N4M ST-N ST-N6M ST-N ST-N8M M01-2-2Y M01-2-4Y M02-2-2Y M02-2-4Y R RF RF RF RF RF RFH RFH RFPL RFPL RFPL V-1000-FOFO...E-10 V-1000-FPFP...E-11 V-1000-MFMF...E-10 V-1000-MOMS...E-10 V-250-FOFO...E-10 V-250-FPFP...E-11 V-250-MFMF...E-10 V-250-MOMS...E-10 V-370-FOFO...E-10 V-370-FPFP...E-11 V-370-MFMF...E-10 V-370-MOMS...E-10 V-500-FOFO...E-10 V-500-FPFP...E-11 V-500-MFMF...E-10 V-500-MOMS...E-10 V-620-FOFO...E-10 V-620-MFMF...E-10 V-620-MOMS...E-10 V-750-FOFO...E-10 V-750-FPFP...E-11 V-750-MFMF...E-10 ppendices * enotes parts that are offered in brass as standard, and are also on page listed. ** Semi Standard, consult factory for price & delivery. III-1 Parker Hannifin orporation Minneapolis, MN 55427

192 ppendices lpha Numeric Index ppendices Part No. Page Part No. Page Part No. Page Part No. Page V-750-MOMS...E-10 M-121-2MP M-121-2FP M-121-4FP M-121-4MP M-122-2FP M-122-2MP M-122-4FP M-122-4MP P , -60 T-1000-MFMF...E-6 T-1000-MFMO...E-6 T-1000-MOMF...E-6 T-1000-MOMS...E-7 T-1000-MSMO...E-7 T-1000-MSMS...E-7 T-1250-MFMF...E-6 T-1250-MFMO...E-6 T-1250-MOMF...E-6 T-1250-MOMS...E-7 T-1250-MSMO...E-7 T-1250-MSMS...E-7 T-250-MFMO...E-6 T-250-MOMF...E-6 T-250-MOMS...E-6 T-370-MFMF...E-6 T-370-MFMO...E-6 T-370-MOMF...E-6 T-370-MOMS...E-7 T-370-MSMO...E-7 T-370-MSMS...E-7 T-500-MFMF...E-6 T-500-MFMO...E-6 T-500-MOMF...E-6 T-500-MOMS...E-7 T-500-MSMO...E-7 T-500-MSMS...E-7 T-620-MFMF...E-6 T-620-MFMO...E-6 T-620-MOMF...E-6 T-620-MOMS...E-7 T-620-MSMO...E-7 T-620-MSMS...E-7 T-750-MFMF...E-6 T-750-MFMO...E-6 T-750-MOMF...E-6 T-750-MOMS...E-7 T-750-MSMO...E-7 T-750-MSMS...E-7 ES EM3/1/4E...F-23 EM3/1/4NPT...F-23 EM3/1/4NPT71...F-23 EM3/1/8E...F-23 EM3/1/8NPT...F-23 EM3/10X1E...F-23 EM3/12X1.5E...F-23 EM3/14X1.5E...F-23 EM3/3/8E...F-23 EM3/7/16-20UNF-2...F-23 EM3/9/16-18UNF-2...F-23 EM3/M8X1OR...F-23 EM3VS...F-24 EZ-251-4FP EZ-251-4H EZ-251-4MP EZ-251-4PL EZ-251-6FP EZ-251-6H EZ-251-6MP EZ-251-6PL EZ304F-4T EZ304F-6T EZ304H-4T EZ304H-6T EZ304M-4T EZ304M-6T EZ304PL-4T EZ304PL-6T EZ306F-6T EZ306F-8T EZ306H-6T EZ306M-6T EZ306PL-6T EZ308F-12T EZ308F-8T EZ308H-8T EZ308M-8T EZ308PL-8T EZ312F-12T EZ312F-16T EZ312M-12T EZ-371-6FP EZ-371-6H EZ-371-6MP EZ-371-6PL EZ-371-8FP EZ FP EZ-501-8FP EZ-501-8H EZ-501-8MP EZ-501-8PL EZ FP EZ MP EZ FP F-372-6FP F-372-8FO F-372-8FP F FO F-502-8FP F FO F FP FE FO FE FO FE-502-8FP FE FO FE FO FEM FO-NL FEM FP-NL FEM FO FEM FP FEM-251-4FP-NL FEM-252-4FP FEM-371-6FP-NL FEM-371-8FO-NL FEM-372-6FP FEM-372-8FO FEM MF-NL FEM MS-NL FEM FO-NL FEM FO-NL FEM-501-8FO-NL FEM-501-8FP-NL FEM MS FEM FO FEM MF FEM FO FEM-502-8FP FEM FO-NL FEM FO FEM FO-NL FEM FP-NL FEM FO FEM FP FER FER FF/FS-1001-TOOL...-24, -32 FF/FS-251-TOOL...-24, -32 FF/FS-371-TOOL...-24, -32 FF/FS-751-TOOL...-24, -32 FF FO FF FP FF-1001-KIT FF-1001-KIT-E FF-1001-KIT-E FF FO FF FP FF-1002-KIT FF-1002-KIT-E FF-1002-KIT-E FF-251-4FP FF-251-4MP FF-251-6F FF-251-KIT FF-251-KIT-E FF-251-KIT-E FF-252-4FP FF-252-4MP FF-252-6F FF-252-KIT FF-252-KIT-E FF-252-KIT-E FF-371-6F FF-371-6FP FF-371-8F FF-371-8FO FF-371-8FP FF-372-6F FF-372-6FP FF-372-8F FF-372-8FO FF-372-8FP FF-372-KIT FF-372-KIT-E FF-372-KIT-E FF FO FF-501-8FP FF FO FF-502-8FP FF-502-KIT FF-502-KIT-E FF-502-KIT-E FF FO FF FP FF-751-KIT FF-751-KIT-E FF-751-KIT-E FF FO FF FP FF-752-KIT FF-752-KIT-E FF-752-KIT-E FH-371-6F FH-371-6FP FH-371-6MP FH-372-6F FH-372-6FP FR FR FR FR , -9 FR , -9 FR FR FS FO FS FP FS-1001-KIT FS-1001-KIT-E FS FO FS FP FS-1002-KIT FS-1002-KIT-E FS-251-4FP FS-251-4MP FS-251-6FO FS-252-4FP FS-252-4MP FS-252-6FO FS-252-KIT FS-252-KIT-E FS-371-6FP FS-371-8FO FS-371-KIT FS-371-KIT-E FS-372-6FP FS-372-8FO FS-372-KIT FS-372-KIT-E FS FO FS-501-8FP FS-501-KIT FS-501-KIT-E FS-501-TOOL FS FO FS-502-8FP FS-502-KIT FS-502-KIT-E FS FO FS FP FS-751-KIT FS-751-KIT-E FS FO FS FP FS-752-KIT FS-752-KIT-E H00E...-6 H H0E...-6 H0F...-6 H12-62L...-8 H12-62N...-8 H12-62-T H12-62-T H12-63L...-8 H12-63N...-8 H12-63-T H12-63-T H III-2 Parker Hannifin orporation Minneapolis, MN 55427

193 ppendices lpha Numeric Index Part No. Page Part No. Page Part No. Page Part No. Page H H H1-62-T H H1-63-T H H1-65M H H1-66M H H1E...-6 H1F...-6 H H H H H H H20P H20P H H2-62-T H H2-63-T H H2-65M H H2-66M H H2-E...-6 H2-PS H2E...-6 H2E-F...-6 H2F...-6 H2F-G...-6, -11 H2G...-6 H2G-F...-6 H2G-J...-6 H H3-62-T H H3-63-T H H3-65M H H3-66M H H H H3-E...-6 H3E...-6 H3E-F...-6 H3F...-6 H3F-G...-6, -11 H3G...-6 H3G-F...-6 H3G-J...-6 H H4-62-T H H4-63-T H H4-65M H H4-66M H4EP...-7 H4F...-7, -11 H4FP...-7, -11 H5E...-7 H5EP...-7 H5F...-7 H5F-G...-7, -11 H5FP...-7, -11 H5G...-7 H5G-F...-7 H5G-J...-7 H H6-62-T H H6-63-T H H6-65M H H6-66M H H H67E-62K...-8 H67E-63K...-8 H67F-62K...-8 H67F-63K...-8 H67G-62K...-8 H67G-63K...-8 H67J-62K...-8 H67J-63K...-8 H68E-67K...-9 H69E-67K...-9 H6E...-7 H6EP...-7 H6FP...-7 H H8-62-T H H8-63-T H H8-65M H H8-66M H H H8P...-7 H H9P...-7 H-251-4FP H-251-4MP HF-121-2FP HF-121-2MP HF-121-4FP HF-121-4MP HF-124-2FP HF-124-2MP HF-124-4FP HF-124-4MP HF-251-4FP HF-251-4FP-S HF-251-4H HF-251-4H-S HF-251-4MP HF-251-4MP-S HF-251-4PL HF-251-4PL-S HF-251-6FP HF-251-6FP-S HF-251-6H HF-251-6H-S HF-251-6MP HF-251-6MP-S HF-251-6PL HF-251-6PL-S HF302F HF302F HF302M HF302M HF304F HF304F HF304H HF304H HF304M HF304M HF304PL HF304PL HF306F HF306F HF306F HF306H HF306H HF306M HF306M HF306M HF306PL HF306PL HF-371-4FP HF-371-4FP-S HF-371-4MP HF-371-4MP-S HF-371-6FP HF-371-6FP-S HF-371-6H HF-371-6H-S HF-371-6MP HF-371-6MP-S HF-371-6PL HF-371-6PL-S HF-371-8FP HF-371-8FP-S HF-371-8H HF-371-8H-S HF-371-8MP HF-371-8MP-S HF-371-8PL HF-371-8PL-S HF404F HF404F HF404H HF404H HF404M HF404M HF404PL HF404PL HF406F HF406F HF406F HF406H HF406H HF406M HF406M HF406M HF406PL HF406PL HF-501-8FP HF-501-8MP HF702F HF702F HF702M HF702M HO-251-4FP HO-252-4FP HO-371-6FP HO-372-6FP HO-501-8FP HO-502-8FP HP FO HP FP HP FO HP FP HP FO HP FP HP FO HP FP HP , -59 HP , -59 HPP , -59 HPP , -59 KEY-K KEY-U KEY-L KEY-GR KEY-NI KEY-R L L MV1/4NPT-M3...F-24 MV1/4NPT-M3-KM...F-24 MVM1/4NPT-M3...F-24 NM01-2-2Y NM01-2-4Y NM02-2-2Y NM02-2-4Y NR NR NR NR NRF S NRF S NRF S NRF S NRFH-4-4-S NRFH-4-6-S NRFPL-4-4-S NRFPL-4-6-S NS F NS FO NS FP NS F NS FO NS FP NS-371-6F NS-371-6FP NS-371-8FO NS-372-6F NS-372-6FP NS-372-8FO NS FO NS-501-8F NS-501-8FP NS FO NS-502-8F NS-502-8FP NS F ppendices III-3 Parker Hannifin orporation Minneapolis, MN 55427

194 ppendices lpha Numeric Index ppendices Part No. Page Part No. Page Part No. Page Part No. Page NS FO NS FP NS F NS FO NS FP P P200-9Y P P P P300-11S P P P300-9Y P P P HF P P P P P P PH-251-4FP PH-251-4MP PH-251-6FP PH-251-6MP PH-371-4FP PH-371-4MP PH-371-6FP PH-371-6MP PH-371-8FP PS-251-4FP PS-251-4MP PS-251-6FP PS-251-6MP PS-371-6FP PS-371-6MP PS-371-8FP PS-371-8MP PS FP PS-501-6FP PS-501-8FP PS-501-8MP P P204V P204V-P P204-P P P205V P P206V P206V-P P206-P P P214V P214V-P P214-P P P215V P P216V P216V-P P216-P P P224V P224V-P P224-P P P225V P P226V P226V-P P226-P P P306-P P306V P306V-P P P308-P P308V P308V-P P P316-P P316V P316V-P P P318-P P318V P318V-P P P326-P P326V P326V-P P P328-P P328V P328V-P P P P504-P P P506-P P P514-P P P516-P P P524-P P P526-P P222...F-19 P240...F-5, F-19 P242...F-19 P243...F-19 P260...F-19 P288...F-9, F-15, F-25 P F-19 P310TL...F-20 P F-19 P312TX...F-20 P F-19 P322...F-19 P323...F-19 P331...F-19 P341...F-19 P342...F-19 P343...F-19 P345...F-20 P346...F-20 P34TL...F-20 P34TX...F-20 P351...F-19 P355...F-20 P357...F-19 P361...F-19 P363...F-19 P365...F-20 P366...F-20 P36TL...F-20 P36TX...F-20 P386...F-20 P38TL...F-20 P38TX...F-20 P F-21 PEM3T-*...F-15 PFS242...F-26 PFS-PROE...F-26 PH-19...F-5, F-14 PP242...F-21 PP288...F-25 PP323...F-22 PP341...F-22 PP343...F-22 PP34TL...F-22 PP34TX...F-22 PP361...F-22 PP36TL...F-22 PP36TX...F-22 PPT-*...F-15 PS3-*...F-9 PSM36-*...F-13 PSM45-*...F-13 PT-*...F-15 PTEM3-*...F-15 PER-251-4FP PER-251-4MP PER-251-6FP PER-251-6MP PES-251-4MP PES-251-6FP PF FP...-9 PF FP...-9 PF M...-9 PF MP...-9 PF FP...-9 PF FP...-9 PF-501-8FP...-9 PF-502-8FP...-9 PFR PFR-1002-NS...-9 PL PN PN PN PN PN PN PN PN PN PN PN251F PN251S PN PN PN PN PN PN PN252F PN252S PN PN253F PN253S PN PN PN PN PN PN PN PN PN PN PN PN352F PN352S PN PN PN PN PN PN PN353F PN353S PN PN PN PN PR PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS III-4 Parker Hannifin orporation Minneapolis, MN 55427

195 ppendices lpha Numeric Index Part No. Page Part No. Page Part No. Page Part No. Page PS PS PS PS PS PS PS PS PS PS PS PS PS PS12-RPR PS12-RPR PS12W-RPR PS12Y-RPR PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS16-RPR PS16-RPR PS16W-RPR PS16Y-RPR PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS4-RPR PS4-RPR PS4W-RPR PS4Y-RPR PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS6-RPR PS6-RPR PS6W-RPR PS6Y-RPR PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS PS ppendices III-5 Parker Hannifin orporation Minneapolis, MN 55427

196 ppendices lpha Numeric Index ppendices Part No. Page Part No. Page Part No. Page Part No. Page PS PS8-RPR PS8-RPR PS8W-RPR PS8Y-RPR RF-251-4FP RF-251-4H RF-251-4MP RF-251-4PL RF-251-6FP RF-251-6H RF-251-6MP RF-251-6PL RF-251-8MP RF-251-8PL RF-254-4FP RF-254-4H RF-254-4MP RF-254-4PL RF-254-6FP RF-254-6H RF-254-6MP RF-254-6PL RF-371-6FP RF-371-6H RF-371-6MP RF-371-6PL RF-371-8FP RF-371-8H RF-371-8MP RF-371-8PL RF-374-6FP RF-374-6H RF-374-6MP RF-374-6PL RF-374-8FP RF-374-8H RF-374-8MP RF-374-8PL RK-12E RK-12N RK-12V RK-16E RK-16N RK-16V RK-4/6E RK-4/6N RK-4/6V RK-8E RK-8N RK-8V S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S2-V-02-FP...-5 S2-V-02-MP...-5 S2-V-03-H...-5 S2-V-03-H...-5 S2-V-04-H...-5 S2-V-04-FP...-5 S2-V-04-H...-5 S2-V-04-MP...-5 S2-NS-02-FP...-6 S2-NS-02-MP...-6 S2-NS-03-H...-6 S2-NS-03-H...-6 S2-NS-04-H...-6 S2-NS-04-FP...-6 S2-NS-04-H...-6 S2-NS-04-MP...-6 S2-NV-02-FP...-7 S2-NV-02-MP...-7 S2-NV-03-H...-7 S2-NV-03-H...-7 S2-NV-04-H...-7 S2-NV-04-FP...-7 S2-NV-04-H...-7 S2-NV-04-MP...-7 S2-PV-02-FP...-5 S2-PV-03-H...-5 S2-PV-04-FP...-5 S2-PV-04-H...-5 S S2-PV-02-FP...-5 S2-PV-02-MP...-5 S2-PV-03-H...-5 S2-PV-03-H...-5 S2-PV-04-H...-5 S2-PV-04-FP...-5 S2-PV-04-H...-5 S2-PV-04-MP...-5 S2-PNS-02-FP...-6 S2-PNS-02-MP...-6 S2-PNS-03-H...-6 S2-PNS-03-H...-6 S2-PNS-04-H...-6 S2-PNS-04-FP...-6 S2-PNS-04-H...-6 S2-PNS-04-MP...-6 S2-PNV-02-FP...-7 S2-PNV-02-MP...-7 S2-PNV-03-H...-7 S2-PNV-03-H...-7 S2-PNV-04-H...-7 S2-PNV-04-FP...-7 S2-PNV-04-H...-7 S2-PNV-04-MP...-7 S2-PPV-02-FP...-5 S2-PPV-03-H...-5 S2-PPV-04-FP...-5 S2-PPV-04-H...-5 S6-V-04-FP...-5 S6-V-04-H...-5 S6-V-04-MP...-5 S6-V-06-FP...-5 S6-V-06-H...-5 S6-V-06-MP...-5 S6-V-08-FP...-5 S6-V-08-H...-5 S6-V-08-MP...-5 S6-NS-04-FP...-6 S6-NS-04-H...-6 S6-NS-04-MP...-6 S6-NS-06-FP...-6 S6-NS-06-H...-6 S6-NS-06-MP...-6 S6-NS-08-FP...-6 S6-NS-08-H...-6 S6-NS-08-MP...-6 S6-NV-04-FP...-7 S6-NV-04-H...-7 S6-NV-04-MP...-7 S6-NV-06-FP...-7 S6-NV-06-H...-7 S6-NV-06-MP...-7 S6-NV-08-FP...-7 S6-NV-08-H...-7 S6-NV-08-MP...-7 S6-KV-04-FP...-5 S6-KV-04-H...-5 S6-KV-04-MP...-5 S6-KV-06-FP...-5 S6-KV-06-H...-5 S6-KV-06-MP...-5 S6-KV-08-FP...-5 S6-KV-08-H...-5 S6-KV-08-MP...-5 S6-KNV-04-FP...-7 S6-KNV-04-H...-7 S6-KNV-04-MP...-7 S6-KNV-06-FP...-7 S6-KNV-06-H...-7 S6-KNV-06-MP...-7 S6-KNV-08-FP...-7 S6-KNV-08-H...-7 S6-KNV-08-MP...-7 S6-PV-04-FP...-5 S6-PV-04-H...-5 S6-PV-04-MP...-5 S6-PV-06-FP...-5 S6-PV-06-H...-5 S6-PV-06-MP...-5 S6-PV-08-FP...-5 S6-PV-08-H...-5 S6-PV-08-MP...-5 S6-PNS-04-FP...-6 S6-PNS-04-H...-6 S6-PNS-04-MP...-6 S6-PNS-06-FP...-6 S6-PNS-06-H...-6 S6-PNS-06-MP...-6 S6-PNS-08-FP...-6 S6-PNS-08-H...-6 S6-PNS-08-MP...-6 S6-PNV-04-FP...-7 S6-PNV-04-H...-7 S6-PNV-04-MP...-7 S6-PNV-06-FP...-7 S6-PNV-06-H...-7 S6-PNV-06-MP...-7 S6-PNV-08-FP...-7 S6-PNV-08-H...-7 S6-PNV-08-MP...-7 SE S F-14 S-1/2-EM-3...F-25 S-7/16-EM-3...F-5 S F-5 III-6 Parker Hannifin orporation Minneapolis, MN 55427

197 ppendices lpha Numeric Index Part No. Page Part No. Page Part No. Page Part No. Page S F-5, F-14 SFT-*...F-16 SJ-1/4...F-5 SJR MP...F-5 SJR-0250-EM...F-5 SJR-0250-P...F-5 SJR MP...F5 SJR-1500-P...F5 SJR-1500-EM...F5 SJR MP...F-5 SJR-5800-EM...F-5 SJR-5800-P...F-5 SJR MP...F-5 SJR-8700-EM...F-5 SJR-8700-P...F-5 SK F-14, F-17 SK F-14, F-17 SK F-14, F-17 SM F-6, F-7, F-8 SM F-10, F-11, F-I2 SM-V F-14, F-17 SRPM F-14, F-17 SRPM F-14, F-17 SRPM F-14, F-17 SSN F-14 SSW F-14, F-17 SSW-KIT F-14, F-17 ST F-14, F-17 ST-1/4...F-14, F-17 SH12-62L...-8 SH12-62N...-8 SH12-62-T SH12-62-T SH12-63L...-8 SH12-63N...-8 SH12-63-T SH12-63-T SH SH1-62-T SH SH1-63-T SH SH SH SH SH SH SH SH2-62-T SH SH2-63-T SH SH2-E...-6 SH SH3-62-T SH SH3-63-T SH SH3-E...-6 SH SH4-62-T SH SH4-63-T SH SH6-62-T SH SH6-63-T SH67E-62K...-8 SH67E-63K...-8 SH67F-62K...-8 SH67F-63K...-8 SH67G-62K...-8 SH67G-63K...-8 SH67J-62K...-8 SH67J-63K...-8 SH SH8-62-T SH SH8-63-T SH SH SM-251-4F SM-251-4FP SM-251-6F SM-251-6FO SM-251-6FP SM-252-4F SM-252-4FP SM-252-6F SM-252-6FO SM-252-6FP SM F SM FP SM-501-8F SM-501-8FO SM-501-8FP SM F SM FP SM-502-8F SM-502-8FO SM-502-8FP SM F SM FO SM FP SM F SM FO SM FP SM F SM FO SM FP SM F SM FO SM FP SM F-25 SM F-25 SM F-5, F-25 SM F-25 SM F-25 SSH12-62LY...-8 SSH12-62NY...-8 SSH12-62Y-T SSH12-62Y-T SSH12-63LY...-8 SSH12-63NY...-8 SSH12-63Y-T SSH12-63Y-T SSH1-62Y...-7 SSH1-62Y-T SSH1-63Y...-7 SSH1-63Y-T SSH Y...-8 SSH Y...-8 SSH Y...-8 SSH Y...-8 SSH Y...-8 SSH Y...-8 SSH2-62Y...-7 SSH2-62Y-T SSH2-63Y...-7 SSH2-63Y-T SSH3-62Y...-7 SSH3-62Y-T SSH3-63Y...-7 SSH3-63Y-T SSH4-62Y...-7 SSH4-62Y-T SSH4-63Y...-7 SSH4-63Y-T SSH6-62Y...-7 SSH6-62Y-T SSH6-63Y...-7 SSH6-63Y-T SSH67E-62KY...-8 SSH67E-63KY...-8 SSH67F-62KY...-8 SSH67F-63KY...-8 SSH67G-62KY...-8 SSH67G-63KY...-8 SSH67J-62KY...-8 SSH67J-63KY...-8 SSH8-62Y...-7 SSH8-62Y-T SSH8-63Y...-7 SSH8-63Y-T SSP242Y...F-19 SSP343Y...F-19 SST SST SST SST SST SST SST-1M SST-2M SST-3M SST-4M SST-6M SST-8M SST-N SST-N1M SST-N SST-N2M SST-N SST-N3M SST-N SST-N4M SST-N SST-N6M SST-N SST-N8M ST-N ST-N1M ST-N ST-N2M ST-N ST-N3M ST-N ST-N4M ST-N ST-N6M ST-N ST-N8M T T TL-251-4FP TL-251-4MP TL-251-6MP TL-254-2FP TL-254-2MP TL-254-4FP TL-254-4H TL-254-4MP TL-254-6H TL FP TL-501-6FP TL-501-6MP TL-501-8FP TL-501-8MP TL MP TL-504-4FP TL-504-4H TL-504-4MP TL-504-6FP TL-504-6H TL-504-6MP TL-504-8H TL-504-8MP TR , -60 U-251-4FP U-251-4MP U-251-6FP U-251-6MP U304F U-304M U-340F U340M E F P F F , , -13 ppendices III-7 Parker Hannifin orporation Minneapolis, MN 55427

198 ppendices lpha Numeric Index ppendices Part No. Page Part No. Page Part No. Page Part No. Page 16-5P...-10, , P...-10, , E...-10, G...-10, , E...-10, G...-10, E F P F F E E F E E F P P...-17, P T P P SPP P P-T8M P P P P P-T T N S SV N S P P P , , ,-19,-39, M M...-58, M M...-58, E EP F M M M M , -19, -37, -39, P...-17, -19, -37, P , , -37, -39, P...-17, -37, SPP , -19, -37, -39, P...-17, -19, -37, P , P P P III-8 Parker Hannifin orporation Minneapolis, MN 55427

199 ppendices Glossary of Terms ir Inclusion: The ambient atmosphere forced into the system during the connection of the quick disconnect halves. reak-way: utomatic disconnection of a coupling when an axial separation force is applied. rinelling: imples or grooves worn into the shoulder of a male half by the locking balls in the female half. urst Pressure: The pressure at which a device loses the capability to retain pressure. ase Hardening: Hardening the surface of low carbon steel.. old Flow: ontinued deformation under load. onnect Under Pressure: bility to connect coupling halves with internal line pressure applied to either both sides or one side. oupling, Female Half: Other nomenclature coupler, socket, body. oupling, Male Half: Other nomenclature nipple, plug, adapter. oupling, Quick isconnect: component which can quickly join or separate a fluid line without the use of tools or special devices. ifferential Pressure ( P): The difference in pressure between any two points of a system or a component. ouble-cting Sleeve: Permits push-to-connect and pull-todisconnect convenience on implement line when female half is clamp mounted and connected with a hose. ust ap: ust or dirt repelling enclosure for both halves. ust Plug: ust or dirt repelling enclosure both halves. Flow hecking: Occurs when a nipple valve closes during flow conditions, such as when quickly lowering a heavy implement. (lso called heck Off, ack hecking or Lock-up.) Flush Position (Valve): When the coupler valve is fully open, allowing maximum oil flow. Force to onnect: xial and/or rotational force required to make a complete connection. Force to isconnect: The reverse of the above. Induction Hardening: Localized hardening of medium carbon steel. Peak Pressure: Maximum momentary pressure encountered in the operation of a component. Pressure ap: ap which incorporates a seal capable of withstanding the rated pressures on the male half. Pressure Impulse Test: Subjecting a component to a specified pressure at a specified rate of increase or decrease for a specified time limit. Pressure Operating: The pressure at which a system is operated. Pressure Plug: Plug which incorporates a seal capable of withstanding the rated pressures on the female half. Proof Pressure: The non-destructive test pressure in excess of the maximum rated operating pressure. Push To onnect (uto Lock): Locking arrangement which permits one handed connection by pushing the nipple into the coupler. Rated Pressure: The maximum pressure at which a product is designed to operate. Single-cting Sleeve: Permits pull-to-disconnect convenience on implement line when female body is clamp mounted. Making connection requires manually pulling female body forward, inserting male tip, then allowing body and tip to return to original position in the clamp. Sleeve Lock: rrangement which provides an additional lock which must be actuated before the locking sleeve can be retracted. Spillage: The fluid removed from the system due to disconnection of a coupling assembly. This is the fluid trapped between the mating seal and the valve seal of the coupling halves. Surge Pressure: The pressure existing from surge conditions. Surge Flows: rapid increase in fluid flow. Thermal uild-up: Hydraulic pressure caused by expansion of the fluid due to heat from an external source such as sunlight. Trapped Pressure: Pressurized hydraulic fluid trapped behind closed coupling valve Twist Lock: locking arrangement which requires a rotational actuation to unlock the mating halves. Types of Quick isconnect oupling Valves Straight-Thru (ST): This provides straight through flow. ouble Shut-off Valve (SO): valve in the female half and a valve in the male half. Single Shut-off Valve (SSO): Generally, a valve in the female half with no valve in the male half. NOTE: Refer to Parker s Publication No : Safety Guide for Selecting and Using Quick ction ouplings and Related ccessories. ppendices IV-1 Parker Hannifin orporation Minneapolis, MN 55427

200 ppendices Offer of Sale The items described in this document are hereby offered for sale at prices to be established by Parker Hannifin orporation, its subsidiaries and its authorized distributors. This offer and its acceptance by any customer ( uyer ) shall be governed by all of the following Terms and onditions. uyer s order for any item described in its document, when communicated to Parker Hannifin orporation, its subsidiary or an authorized distributor ( Seller ) verbally or in writing, shall constitute acceptance of this offer. ppendices 1. Terms and onditions of Sale: ll descriptions, quotations, proposals, offers, acknowledgments, acceptances and sales of Seller s products are subject to and shall be governed exclusively by the terms and conditions stated herein. uyer s acceptance of any offer to sell is limited to these terms and conditions. ny terms or conditions in addition to, or inconsistent with those stated herein, proposed by uyer in any acceptance of an offer by Seller, are hereby objected to. No such additional, different or inconsistent terms and conditions shall become part of the contract between uyer and Seller unless expressly accepted in writing by Seller. Seller s acceptance of any offer to purchase by uyer is expressly conditional upon uyer s assent to all the terms and conditions stated herein, including any terms in addition to, or inconsistent with those contained in uyer s offer. cceptance of Seller s products shall in all events constitute such assent. 2. Payment: Payment shall be made by uyer net 30 days from the date of delivery of the items purchased hereunder. mounts not timely paid shall bear interest of 1% for each month or a portion thereof that uyer is late in making payment. ny claims by uyer for omissions or shortages in a shipment shall be waived unless Seller receives notice thereof within 30 days after uyer s receipt of the shipment. 3. elivery: Unless otherwise provided on the face hereof, delivery shall be made F.O.. Seller s plant. Regardless of the method of delivery, however, risk of loss shall pass to uyer upon Seller s delivery to a carrier. ny delivery dates shown are approximate only and Seller shall have no liability for any delays in delivery. 4. Warranty: Seller warrants that the items sold hereunder shall be free from defects in material or workmanship for a period of 365 days from the date of shipment to uyer. THIS WRRNTY OMPRISES THE SOLE N ENTIRE WRRNTY PERTIN- ING TO ITEMS PROVIE HEREUNER. SELLER MKES NO OTHER WRRNTY, GURNTEE, OR REPRESENTTION OF NY KIN WHTSOEVER. LL OTHER WRRNTIES, INLUING UT NOT LIMITE TO, MERHNTIILITY N FITNESS FOR PURPOSE, WHETHER EXPRESS, IMPLIE, OR RISING Y OPERTION OF LW,TRE USGE, OR OURSE OF ELING RE HEREY ISLIME. NOTWITHSTNING THE FOREGOING, THERE RE NO WRRNTIES WHT- SOEVER ON ITEMS UILT OR QUIRE WHOLLY OR PRTILLY,TO UYER S ESIGNS OR SPEIFITIONS. 5. Limitation Of Remedy: SELLER S LIILITY RISING FROM OR IN NY WY ONNETE WITH THE ITEMS SOL OR THIS ONTRT SHLL E LIMITE EXLUSIVELYTO REPIR OR REPLEMENT OF THE ITEMS SOL OR REFUN OF THE PURHSE PRIE PI Y UYER, T SELLER S SOLE OPTION. IN NO EVENT SHLL SELLER E LILE FOR NY INIENTL, ON- SEQUENTIL OR SPEIL MGES OF NY KIN OR NTURE WHTSOEVER, INLUING UT NOT LIMITE TO LOST PROFITS RISING FROM OR IN NY WY ONNETE WITH THIS GREEMENT OR ITEMS SOL HEREUNER, WHETHER LLEGE TO RISE FROM REH OF ONTRT, EXPRESS OR IMPLIE WRRNTY, OR IN TORT, INLUING WITHOUT LIMITTION, NEGLI- GENE, FILURE TO WRN OR STRIT LIILITY. 6. hanges, Reschedules and ancellations: uyer may request to modify the designs or specifications for the items sold hereunder as well as the quantities and delivery dates thereof, or may request to cancel all or part of this order, however, no such requested modification or cancellation shall become part of the contract between uyer and Seller unless accepted by Seller in a written amendment to this greement. cceptance of any such requested modification or cancellation shall be at Seller s discretion, and shall be upon such terms and conditions as Seller may require. 7. Special Tooling: tooling charge may be imposed for any special tooling, including without limitation, dies, fixtures, molds and patterns, acquired to manufacture items sold pursuant to this contract. Such special tooling shall be and remain Seller s property notwithstanding payment of any charges by uyer. In no event will uyer acquire any interest in apparatus belonging to Seller which is utilized in the manufacture of the items sold hereunder, even if such apparatus has been specially converted or adapted for such manufacture and notwithstanding any charges paid by uyer therefore. Unless otherwise agreed, Seller shall have the right to alter, discard or otherwise dispose of any special tooling or other property in its sole discretion at any time. 8. uyer s Property: ny designs, tools, patterns, materials, drawings, confidential information or equipment furnished by the uyer or any other items which become uyer s property, may be considered obsolete and may be destroyed by Seller after two (2) consecutive years have elapsed without uyer placing an order for the items which are manufactured using such property. Seller shall not be responsible for any loss or damage to such property while it is in Seller s possession or control. 9. Taxes: Unless otherwise indicated on the face hereof, all prices and charges are exclusive of excise, sales, use, property, occupational or like taxes which may be imposed by any taxing authority upon the manufacture, sale or delivery of the items sold hereunder. If any such taxes must be paid by Seller or if Seller is liable for the collection of such tax, the amount thereof shall be in addition to the amounts for the items sold. uyer agrees to pay all such taxes or to reimburse Seller therefore upon receipt of its invoice. If uyer claims exemption from any sales, use or other tax imposed by any taxing authority, uyer shall save Seller harmless from and against any such tax, together with any interest or penalties thereon which may be assessed if the items are held to be taxable. 10. Indemnity For Infringement of Intellectual Property Rights: Seller shall have no liability for infringement of any patents, trademarks, copyrights, trade dress, trade secrets or similar rights except as provided in this Part 10. Seller will defend and indemnify uyer against allegations of infringement of U.S. patents. U.S. trademarks, copyrights, trade dress and trade secrets (hereinafter Intellectual Property Rights ). Seller will defend at its expense and will pay the cost of any settlement or damages awarded in an action brought against uyer based on an allegation that an item sold pursuant to this contract infringes the Intellectual Property Rights of a third party. Seller s obligation to defend and indemnify uyer is contingent on uyer notifying Seller within ten (10) days after uyer becomes aware of such allegations of infringement, and Seller having sole control over the defense of any allegations or actions including all negotiations for settlement or compromise. If an item sold hereunder is subject to a claim that it infringes the Intellectual Property Rights of a third party, Seller may, at its sole expense and option, procure for uyer the right to continue using said item, replace or modify said item so as to make it noninfringing, or offer to accept return of said item and return the purchase price less a reasonable allowance for depreciation. Notwithstanding the foregoing, Seller shall have no liability for claims of infringement based on information provided by uyer, or directed to items delivered hereunder for which the designs are specified in whole or part by uyer, or infringements resulting from the modification, combination or use in a system of any item sold hereunder.the foregoing provisions of this Part 10 shall constitute Seller s sole and exclusive liability and uyer s sole and exclusive remedy for infringement of Intellectual Property rights. If a claim is based on information provided by uyer or if the design for an item delivered hereunder is specified in whole or in part by uyer, uyer shall defend and indemnify Seller for all costs, expenses or judgments resulting from any claim that such item infringes any patent, trademark, copyright, trade dress, trade secret or any similar right. 11. Force Majeure: Seller does not assume the risk of and shall not be liable for delay or failure to perform any of Seller s obligations by reason of circumstances beyond the reasonable control of Seller (hereinafter Events of Force Majeure ). Events of Force Majeure shall include without limitation, accidents, acts of God, strikes or labor disputes, acts, laws, rules or regulations of any government or government agency, fires, floods, delays or failures in delivery of carriers or suppliers, shortages of materials and any other cause beyond Seller s control. 12. Entire greement/governing Law: The terms and conditions set forth herein, together with any amendments, modifications and any different terms or conditions expressly accepted by Seller in writing, shall constitute the entire greement concerning the items sold, and there are no oral or other representations or agreements which pertain thereto.this greement shall be governed in all respects by the law of the State of Ohio. No actions arising out of the sale of the items sold hereunder or this greement may be brought by either party more than two (2) years after the cause of action accrues. V-1 Parker Hannifin orporation Minneapolis, MN 55427

201 Parker Hannifin orporation 6035 Parkland lvd. leveland, Ohio Telephone: (216) Fax: (216) Parker Hannifin orporation bout Parker Hannifin orporation Parker Hannifin is a leading global motion-control company dedicated to delivering premier customer service. Fortune 500 corporation listed on the New York Stock Exchange (PH), our components and systems comprise over 1,400 product lines that control motion in some 1,000 industrial and aerospace markets. Parker is the only manufacturer to offer its customers a choice of hydraulic, pneumatic, and electromechanical motion-control solutions. Our ompany has the largest distribution network in its field, with over 7,500 distributors serving nearly 400,000 customers worldwide. Parker s harter To be a leading worldwide manufacturer of components and systems for the builders and users of durable goods. More specifically, we will design, market and manufacture products controlling motion, flow and pressure. We will achieve profitable growth through premier customer service. Product Information North merican customers seeking product information, the location of a nearby distributor, or repair services will receive prompt attention by calling the Parker Product Information enter at our toll-free number: PRKER ( ). In Europe, call: PRKER-H ( ). The erospace Group is a leader in the development, design, manufacture and servicing of control systems and components for aerospace and related high-technology markets, while achieving growth through premier customer service. The limate & Industrial ontrols Group designs, manufactures and markets system-control and fluid-handling components and systems to refrigeration, air-conditioning and industrial customers worldwide. The Fluid onnectors Group designs, manufactures and markets rigid and flexible connectors, and associated products used in pneumatic and fluid systems. The Seal Group designs, manufactures and distributes industrial and commercial sealing devices and related products by providing superior quality and total customer satisfaction. The Hydraulics Group designs, produces and markets a full spectrum of hydraulic components and systems to builders and users of industrial and mobile machinery and equipment. The Filtration Group designs, manufactures and markets quality filtration and clarification products, providing customers with the best value, quality, technical support, and global availability. The utomation Group is a leading supplier of pneumatic and electromechanical components and systems to automation customers worldwide. The Instrumentation Group is a global leader in the design, manufacture and distribution of high-quality critical flow components for worldwide process instrumentation, ultra-high-purity, medical and analytical applications.

202 Fluid onnectors Group Sales Offices Parker Hannifin orporation 8145 Lewis Road Minneapolis, MN (763) FX (763) Parker Hannifin Rak S.. 17, rue des uchillons Z.I. du Mont-lanc.P nnemasse edex France Tel FX Your complete source for quality tube fittings, hose and hose fittings, brass fittings and valves, quick-disconnect couplings, and asssembly tools, locally-available from a worldwide network of authorized distributors. Fittings & ouplings: vailable in inch and metric sizes covering SE, SP, IN, GZ, JIS and ISO thread configurations, manufactured from steel, stainless steel, brass, aluminum, nylon and thermoplastic. Hose,Tubing and undles: vailable in a wide variety of sizes and materials including rubber, wire-reinforced thermoplastic, hybrid and custom compounds. Worldwide vailability: Parker operates Fluid onnectors manufacturing locations and sales offices throughout North merica, South merica, Europe and sia-pacific. For information, contact the nearest Regional Sales Office listed, or call toll-free PRKER ( ). Great Lakes Region 300 Parker rive Otsego, MI (616) FX (616) leveland Region 6035 Parkland lvd. leveland, OH (216) FX (216) Minneapolis Region 8145 Lewis Road Minneapolis, MN (763) FX (763) Northeast Region 2605 Kruser Rd. P.O. ox 8847 Trenton, NJ (609) FX (609) Pacific Region 6458 N. asin ve. Portland, OR (503) FX (503) Southeast Region 125 East Meadowview Rd. Greensboro, N (336) FX (336) Southwest Region 800 South 4th ve. Mansfield, TX (817) FX (817) N Parker Hannifin (anada), Inc urham Road South P.O. ox 158 Grimsby, Ontario L3M 4G4 (905) FX (905) Parker Hannifin orporation Fluid onnectors Group 8145 Lewis Road Minneapolis, MN atalog 3800/US - 10M. 11/08 GR JR