AIR LINE VALVES AND GAUGES

Transcription

1 AIR LINE VALVES AND GAUGES INGERSOLL-RAND AIR LINE VALVES AND GAUGES Maintaining consistent air pressure throughout the entire system is crucial for maximum performance and productivity. Ingersoll-Rand carries a full line of durably built valves, strainers, and pressure gauges that ensure you ve got the power you need when you need it. 1

2 2 INGERSOLL-RAND AIR LINE VALVES AND GAUGES BALL VALVES Provide extended service life and resist failure caused by severe temperature applications Full-flow design assures maximum system efficiency Highly inert PTFE seats provide resistance to chemical corrosion Two Viton o-rings at the stem provide maximum safety with no maintenance Blow-out proof system, chrome-plated brass ball, and specifically designed handle enable increased turning leverage for easy opening and closing Available in female pipe sizes Ball Valves Part Number Size NPT B L M N D Ball Valves /2" 0.98" 5.1" 2.32" 1.69" 0.59" /4" 1.22" 5.98" 2.52" 1.97" 0.75" " 1.57" 6.32" 3.19" 2.13" 0.945" /4" 1.93" 8.05" 3.66" 3.98" 1.18" /2" 2.13" 8.23" 4.02" 4.43" 1.5" " 2.69" 8.58" 4.76" 5.02" 1.89" /2" 3.35" 13.11" 6.14" 5.2" 2.52" " 3.89" 13.52" 6.97" 5.51" 3" Please be aware that ball valves are intended for use in the fully open or closed positions. Depending on application conditions, throttling of the valve may result in premature seal failure and/or inability to turn the valve handle

3 INGERSOLL-RAND AIR LINE VALVES AND GAUGES 3 ARO-STOP VALVE ARO-STOP valves shut off air to pump when material containers are empty or fluid lines are broken. They also feature quick-set and reset capabilities. ARO-STOP Valves Part Air Inlet Number NPT (F) ARO -STOP Valves Air Outlet NPT (F) *Maximum flow rate of psi. Pressure Range psi (bar) * 1/4" 1/4" (1.4 12) /2" 1/2" (1.4 12) Protect Your Investment Pump runaway results when your material container is depleted and the pump cycles fast and needlessly. Protect your pump investment with an ARO -STOP valve. For Use With Thunder Series, Series 200, & 1/2" diaphragm pump (includes connecting hose) Series 425, Series 600, & 1" diaphragm pump LOW LEVEL CUT-OFF Low level cut-off prevents air from entering the fluid line by closing the pump intake when material supply is exhausted. Cut-off also threads to the bottom of siphon tube for immersion in fluid, and serves as a check valve. Low Level Cut-off For Use With Low Level Cut-off* Series 200 and Series 425 pumps with 1-1/2" NPT (F) threads, Thunder Series 3" air motor pumps *Not for pumps that exceed 6 gpm. PRESSURE RELIEF VALVE / VALVE KIT Pressure Relief Valve / Valve Kit Part Description Number Pressure Relief Valve / Valve Kit Pressure relief valve is used on material outlet side of pump to automatically allow bleed-back of material to container in applications where thermal expansion is present Pressure relief valve kit includes relief valve reducing bushing, compression coupling, 3' of plastic drain tubing, & grommet

4 4 INGERSOLL-RAND AIR LINE VALVES AND GAUGES PIPE LINE VALVE A sturdy, quick-acting valve that goes from full flow to off with only a 1/4 turn. Pipe Line Valve NPT Description Pipe Line Valve C /4" 4-way shut-off valve PIPE LINE AIR STRAINERS Our strong and efficient air strainers are designed to permit free passage of air. They can be cleaned quickly by removing the plug from the strainer cap and turning air on momentarily. Pipe Line Air Strainers Female NPT Pipe Line Air Strainers EU-A267 3/4" HU-A267AT 1" K4U-A267AT 1-1/4" ST /2" ST "

5 INGERSOLL-RAND AIR LINE VALVES AND GAUGES 5 PRESSURE GAUGES Pressure Gauges NEEDLE PRESSURE GAUGE Pressure Rating psi kpa Port Size Dial Size Mounting Type Pressure Gauges " 2.5" Center back mount " 2.5" Center back mount " 2.5" Center back mount " 2.5" Center back mount " 2.5" Center back mount " 2.5" Lower mount " 4" Lower mount , " 2.5" Center back mount , " 2.5" Center back mount , " 2.5" Lower mount , " 4" Lower mount , " 2.5" Center back mount , " 2.5" Lower mount , " 4" Lower mount , " 2.5" Center back mount , " 4" Lower mount ,000 7, " 2.5" Center back mount ,000 7, " 4" Lower mount ,500 10, " 2.5" Center back mount ,000 14, " 2.5" Center back mount ,000 20, " 2.5" Center back mount ,000 60, " 2.5" Center back mount Pressure gauges are critical to any installation. Ingersoll-Rand offers a full range (15 psi 10,000 psi) of liquid-filled pressure gauges. Ingersoll-Rand gauges are built in a durable stainless steel case with a vent plug and copper alloy fittings. Needle Pressure Gauge Needle Pressure Gauge NPG-A1 NPG-2 Description Gauge kit Needle & cleaning wire kit Utilizing our needle pressure gauge is one of the simplest ways to check actual air pressure of the equipment while it is operating, determining whether or not the equipment is receiving adequate air pressure. The hypodermic needle easily pierces any size rubber air hose, and, if properly inserted, will not cause a leak when withdrawn. The Ingersoll-Rand needle pressure gauge kit consists of a convenient carrying pouch, an easy-to-read pressure gauge, a needle guard, two hypodermic needles, and two cleaning wires.