VCR Metal Gasket Face Seal Fittings
|
|
- Doreen Allison
- 8 years ago
- Views:
Transcription
1 Metal Gasket Face Seal Fittings 1/16 to 1 in. and 6 to 18 mm sizes High-purity stainless steels The original design, the authentic brand
2 2 Metal Gasket Face Seal Fittings ontents Typical ssemblies... 2 Features... 3 Materials of onstruction... 3 Pressure Ratings... 3 Temperature Ratings... 3 Testing... 3 leaning... 4 Ultrahigh-Purity Processing... 4 Information, Pressure Ratings, and.. 4 Glands utt Weld... 5 Socket Weld... 6 Male Weld... 7 dapter... 7 lind... 7 odies Male onnectors... 8 Female onnector... 9 Swagelok Fitting onnector... 9 Male Unions utt Weld ulkhead onnector oupling Reducers lbows, Tee, ross Welded ssemblies Male NPT onnector Female NPT onnector Swagelok Fitting onnector Rotating Female Union Nuts, aps, and Plugs High-Flow onnections H Type Glands odies Nuts Gaskets Options and ccessories Flow Restrictors Lock and Tag evices Side-Load Installation Tool and Tray Installation Instructions Typical ssemblies Female nut Gland Side-load retainer gasket Gland Male nut OR Female nut Gland Gasket ody
3 Metal Gasket Face Seal Fittings 3 Features Swagelok fittings offer the high purity of a metalto-metal seal, providing leak-tight service from vacuum to positive pressure. The seal on a assembly is made when the gasket is compressed by two beads during the engagement of a male nut or body hex and a female nut. Minimal clearance required for removal Side-load retainer gasket for easy installation and minimal clearance for removal Standard surface finish on glands and bodies is a roughness average of 10 µin. ( µm) R a Test port at two locations for easy leak testing Markings identify manufacturer, material, and when applicable, the appropriate process designator, in accordance with Swagelok Ultrahigh-Purity Process Specification (S 01), MS No virtual leak zones Precision manufactured gasket for maximum performance Female threads are silver plated to prevent galling, ensure easy, consistent assembly Material heat code is stamped on glands and all shapes to ensure raw material traceability Materials of onstruction Material esignator Specification Glands, odies, and Nuts ar stock: SM S479 STM stainless steel SS Forged shapes: SM S182 STM 314 S17400 SS Split-nut assemblies: MPIF Standard L stainless steel 316L ar stock: SM S479 STM 276 Forged shapes: SM L VR stainless steel 6LV SMI F High-Purity➀ Gaskets Nickel NI STM F3 316L stainless steel SS STM 240 opper U STM 152 ➀ 20 % minimum elongation allowed. Plating female nuts are silver plated. void chemical processes used for cleaning, electropolishing, and passivation that will remove plating. If the plating is damaged or removed, thread galling may occur, damaging fitting components and preventing a proper seal. Pressure Ratings ll ratings comply with calculations in accordance with SM ode for Pressure Piping 31.3, Process Piping, and SM 31.1, Power Piping. Working pressure ratings determined at room temperature with gasket materials shown. Temperature Ratings omponents Material Temperature, F ( ) Fittings 316 stainless steel 316L stainless steel 316L VR stainless steel 1000 (537) 316L stainless steel 1000 (537) Gaskets Nickel 600 (315) opper 400 (204) Testing The fitting design has been helium leak tested to a maximum leak rate of std cm 3 /s with silver-plated and copper gaskets and to a maximum leak rate of std cm 3 /s with unplated gaskets.
4 4 Metal Gasket Face Seal Fittings leaning omponents are cleaned to remove oil, grease, and loose particles. For more information, see Swagelok Standard leaning and Packaging (S-10), MS Ultrahigh-Purity Processing variety of face seal glands and bodies is available with controlled surface finishes, electropolished, and specially cleaned to meet ultrahigh-purity system requirements. For more information, see Swagelok Ultrahigh- Purity Process Specification (S-01), MS Information, Pressure Ratings, and are for reference only and are subject to change. The dimension refers to the smallest nominal inside diameter of the part. To order fittings manufactured in accordance with Swagelok Ultrahigh-Purity Process Specification (S-01), MS-06-61, add P to the ordering number. xample: 6LV T7P Glands Short utt Weld Nominal Wall Thickness 1/ / in /8 6LV-2--3S-2T7➀ (27.4) /4 6LV-4--3S-2T7 (27.9) 1/4 3/ /2 1/ /2 6LV-4--3S-4T2 6LV-4--3S-4T3 6LV-4--3S-4T7 1/2 6LV-8--3S-4T7 6LV-8--3S-6T2 6LV-8--3S-6T7 6LV-8--3S-8T2 6LV-8--3S-8T3 6LV-8--3S-8T7 Ni SS u 0.60 (15.2) 0.72 (18.3) 1.10 (27.9) 1.12 (28.4) 1.12 (28.4) 0.74 (18.8) 1.12 (28.4) 0.38 (9.6) 0.06 (1.5) 0.31 (7.9) 0.38 (9.6) 8500 (585) 8500 (585) 6800 (468) 2600 (179), mm (in.) /4 6LV-4--3S-6MT /4 6LV-4--3S-8MT /2 6LV-8--3S-10MT /2 6LV-8--3S-12MT /4 6LV-12--3S-18MT (1.16) 29.5 (1.16) 29.5 (1.16) 29.5 (1.16) 31.0 (1.22) 19.1 () 4.0 (0.16) 6.0 (0.24) 8.0 (0.31) 10.0 (0.39) 15.0 (0.59) 468 (6800) 337 (4900) 241 () 213 (3100) 206 () bar (psig) 468 (6800) 337 (4900) 241 () 213 (3100) 206 () 372 (5400) 337 (4900) 192 () 165 () 165 () ➀ Not designed for gasket retainer assembly.
5 Metal Gasket Face Seal Fittings 5 Glands Long utt Weld Nominal Wall Thickness in. 1/ /8 6LV T7➀ 1/ /4 3/ /2 1/ /2 6LV T2 6LV LV T3 6LV T7 1/2 6LV T7 6LV T2 6LV T7 6LV T2 6LV T3 6LV T7 3/ /4 6LV T LV T7 Ni SS u 1.42 (36.1) 1.20 (30.5) 1.31 (33.3) 1.32 (33.5) 1.70 (43.2) 1.80 (45.7) 1.29 (32.8) 1.79 (45.5) 1.29 (32.8) 1.41 (35.8) 1.79 (45.5) 2.03 (51.6) 2.32 (58.9) 0.36 (9.1) 0.38 (9.6) (1.5)➁ (585) 0.31 (7.9) 0.38 (9.6) 0.65 (16.5) 0.87 (22.1) 8500 (585) 6800 (468) 2600 (179), mm (in.) /4 6LV MT /4 6LV MT /2 6LV MT /2 6LV MT /4 6LV MT (1.70) 43.2 (1.70) 45.5 (1.79) 45.5 (1.79) 51.6 (2.03) 19.1 () 4.0 (0.16) 6.0 (0.24) 8.0 (0.31) 10.0 (0.39) 15.0 (0.59) 468 (6800) 337 (4900) 241 () 213 (3100) 206 () bar (psig) 468 (6800) 337 (4900) 241 () 213 (3100) 206 () 372 (5400) 337 (4900) 192 () 165 () 165 () ➀ Not designed for gasket retainer assembly. ➁ May contain internal diameter transitions. Short utomatic utt Weld Nominal Wall Thickness in. 1/ /4 316L-4--3S 3/ /2 316L-8--3S6 1/ /2 316L-8--3S Ni SS u 1.12 (28.4) 1.15 (29.2) 1.16 (29.5) 0.02 (0.5) 0.03 (0.8) 0.04 (1.0) 0.31 (7.9) 0.29 (7.4) 0.41 (10.4) 0.55 (14.0) 2600 (179) 6, mm (in.) 1/4 316L MS 8 1/4 316L MS /2 316L MS 12 1/2 316L MS 30.0 (1.18) 30.2 (1.19) 31.0 (1.22) 30.5 (1.20) 19.1 () 0.5 (0.02) 0.8 (0.03) 0.8 (0.03) 1.0 (0.04) 4.0 (0.16) 6.0 (0.24) 8.0 (0.31) 10.0 (0.39) 6.8 (0.27) 8.9 (0.35) 10.9 (0.43) 13.2 (0.52) 468 (6800) 337 (4900) 241 () 213 (3100) bar (psig) 468 (6800) 337 (4900) 241 () 213 (3100) 372 (5400) 337 (4900) 192 () 165 ()
6 6 Metal Gasket Face Seal Fittings Glands Long utomatic utt Weld Nominal Wall Thickness 1/ in. 1/4 316L /2 316L / /2 316L / /2 316L / /4 316L L Ni SS u 1.72 (43.7) 1.82 (46.2) 1.82 (46.2) 1.83 (46.5) 2.07 (52.6) 2.57 (65.3) 0.96 (24.4) 0.02 (0.5) 0.03 (0.8) 0.04 (1.0) 0.04 (1.0) 0.04 (1.0) 0.31 (7.9) 0.65 (16.5) 0.87 (22.1) 0.29 (7.4) 0.41 (10.4) 0.55 (14.0) 0.80 (20.3) 1.06 (26.9) 2600 (179), mm (in.) /4 316L M /2 316L M /4 316L M 43.7 (1.72) 46.5 (1.83) 52.6 (2.07) 19.1 () 0.5 (0.02) 1.0 (0.04) 1.0 (0.04) 4.0 (0.16) 10.0 (0.39) 15.0 (0.59) 6.8 (0.27) 13.2 (0.52) 19.3 (0.76) 468 (6800) 213 (3100) 206 () bar (psig) 468 (6800) 213 (3100) 206 () 372 (5400) 165 () 165 () Socket Weld Socket /16 1/8 SS-1--3➀➁ (17.8) /8 1/8 SS-2--3➁ (17.8) /4 1/4 SS-4--3 (33.3) /8 1/2 SS-6--3➂ (38.1) /2 1/2 SS-8--3 (38.1) SS /4 3/4 SS SS Ni SS u 1.56 (39.6) 2.00 (50.8) 2.22 (56.4) 0.10 (2.5) 0.10 (2.5) (7.1) 0.31 (7.9) 0.38 (9.6) 0.41 (10.4) (11.2) 0.05 (1.3) (7.1) 0.50 (12.7) 0.87 (22.1) 0.13 (3.3) 0.20 (5.1) 0.35 (8.9) 0.60 (15.2) 0.60 (15.2) 0.72 (18.3) 0.88 (22.4) 1.19 (30.2) 9000 (620) 7100 (489) 5500 (378) 9000 (620) 7100 (489) 5500 (378) 7200 (496) 7100 (489) 5500 (378) 2200 (151) 2200 (151) ➀ Uses 1/8 in. gasket and nut. ➁ Not designed for gasket retainer assembly. ➂ Uses 1/2 in. gasket and nut. Short Socket Weld Socket 1/4 1/4 SS LG 0.50 (12.7) SS LG (7.1) Ni SS u 0.35 (8.9) 5500 (378) 5500 (378) 5500 (378)
7 Metal Gasket Face Seal Fittings 7 Glands Reducing Socket Weld Socket 1/8 1/4 SS TSW 1.31 (33.3) 1/4 1/2 SS TSW 1.50 (38.1) Ni SS u 0.10 (2.5) (7.1) ➀ 0.35 (8.9) 0.60 (15.2) ➀ May contain internal diameter transitions. Male Weld Ni SS u 1/8 1/ /8 SS MTW➀ (17.8) 1/4 SS MTW 1.31 (7.1) (33.3) 1/4 SS MTW 1.31 (33.3) /2 SS MTW 1.50 (10.4) (38.1) 3/8 1/2 SS MTW 1/2 1/2 SS MTW 3/4 3/4 SS MTW 1 1 SS MTW 1.50 (38.1) 1.50 (38.1) 2.00 (50.8) 2.22 (56.4) 0.41 (10.4) 0.50 (12.7) 0.81 (20.6) 0.06 (1.5)➁ 0.12 (3.0) (7.1) 0.53 (13.5) 9000 (620) (771) 3700 (254) 7200 (496) ➀ Not designed for gasket retainer assembly. ➁ May contain internal diameter transitions. dapter Ni SS u 1/4 1/4 SS T 1.62 (41.0) 3/8 1/2 SS T 1.81 (46.0) 1/2 1/2 SS T 1.94 (49.3) 0.64 (16.2) 0.70 (17.8) 0.96 (24.4) 0.17 (4.3) 0.27 (6.8)➀ 0.37 (9.4) ➀ May contain internal diameter transitions. lind (Undrilled) Gland 1/8 SS-2--3-L➀ 0.70 (17.8) 1/4 SS-4--3-L 1.31 (33.3) 1/2 SS-8--3-L 1.50 (38.1) 3/4 SS L 2.00 (50.8) 1 SS L 2.22 (56.4) ➀ Not designed for gasket retainer assembly.
8 8 Metal Gasket Face Seal Fittings odies Male NPT onnector➀ NPT /16 1/8 SS ➁ (27.2) 1/8 1/4 F Ni SS u 0.38 (9.6) /8 SS ➁ (27.2) /4 SS (9.6) (33.3) 1/4 SS (37.8) /2 SS (14.2) (41.9) 3/8 1/2 SS /2 1/2 SS /4 3/4 SS SS (41.9) 1.84 (46.7) 2.19 (55.6) 2.47 (62.7) 0.56 (14.2) 0.94 (23.9) /8 ➂ (620) (620) ➂ 7/ (620) (620) (7.1)➂ 15/ /16 (9.6) 15/ /16 (254) (22.1) 7200 (496) 7200 (496) Select male connectors are available with ISO/SP tapered thread (RT) ends. ontact your authorized Swagelok representative. ➀ components with fixed threads must remain stationary during installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts. ➁ Not designed for gasket retainer assembly. ➂ May contain internal diameter transitions. F 1 flat Male NPT ulkhead onnector ➀ 1 L NPT 1/4 1/4 SS M 2.21 (56.1) 1/2 SS M 2.34 (59.4) 1 F F 1 L 0.56 (14.2) (7.1) 13/16 15/16 13/ (31.5) Panel Hole ia 21/32 (16.8) Max Panel Thickness Ni SS u 0.38 (9.7) 4370 (301) ➀ components with fixed threads must remain stationary during installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts. Straight Thread O-Ring Seal Male onnector ➀ 1 Straight Thread Uniform O-Ring➁ 9/ /4 906 SS (33.8) 7/8-14 1/2 910 SS (42.2) 9/ /2 906 SS (37.6) 1 F Ni SS u 0.39 (9.9) 0.50 (12.7) 0.39 (9.9) (7.1) (7.1) (7.1) 0.59 (15.0) (7.1) 3/ (310) 15/ (310) ➀ components with fixed threads must remain stationary during installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts. ➁ Fluorocarbon FKM is standard, other materials are available. O-rings are assembled with a silicone vacuum grease (310)
9 Metal Gasket Face Seal Fittings 9 odies Female NPT onnector ➀ NPT /16 1/8 SS ➁ (27.9) 1/ /8 SS ➁ (30.2) /4 SS (35.8) 1/4 1/4 SS (39.1) 3/8 1/2 SS (44.7) 1/2 1/2 SS (50.5) 3/4 3/4 SS (59.9) 1 1 SS (63.8) F Ni SS u 0.87 (22.1) 7/16 9/16 3/4 15/16 1 1/16 1 5/ (461) 6500 (447) 6600 (454) 6700 (461) 6500 (447) 6600 (454) 3700 (254) 6700 (461) 6500 (447) 5200 (358) ➀ components with fixed threads must remain stationary during installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts. ➁ Not designed for gasket retainer assembly. Swagelok Fitting onnector ➀ G flat 1/8 1/4 SS /4 1/4 SS /8 1/2 SS /2 1/2 SS F G Ni SS u 1.53 (38.9) 1.62 (41.1) 1.84 (46.7) 1.95 (49.5) 0.60 (15.2) 0.70 (17.8) 0.76 (19.3) 0.86 (21.8) 0.50 (12.7) 0.60 (15.2) 0.66 (16.8) 0.90 (22.9) 7/16 ➁ 9/16 (7.1)➁ 15/16 11/16 15/16 7/8,, and are typical finger-tight. Swagelok nuts and ferrules are provided assembled, as shown. For tubing maximum pressure ratings for use with Swagelok tube fittings, see Swagelok Tubing ata, MS ➀ components with fixed threads must remain stationary during installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts. ➁ May contain internal diameter transitions. F 1 flat G flat Swagelok Fitting ulkhead onnector ➀ 1/4 1/4 SS SS-4--1S-400 3/8 1/2 SS /2 1/2 SS F F 1 G 2.25 (57.2) 1.88 (47.8) 2.54 (64.5) 2.74 (69.6) 1.32 (33.5) (15.2) (26.7) 1.45 (36.8) 1.65 (41.9) 0.66 (16.8) 0.90 (22.9) (7.1) 9/16 15/16 3/4 11/16 15/16 15/16 7/8 Panel Hole Max Panel Thickness Ni SS u,, and are typical finger-tight. Swagelok nuts and ferrules are provided assembled, as shown. For tubing maximum pressure ratings for use with Swagelok tube fittings, see Swagelok Tubing ata, MS ➀ components with fixed threads must remain stationary during installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts. 15/32 (11.9) 19/32 (15.0) 25/32 (19.8) 0.13 (3.3) (11.2) 0.50 (12.7)
10 10 Metal Gasket Face Seal Fittings odies Male Union➀ /8 SS-2--6-M➁ (28.7) 1/4 SS-4--6-M 1.55 (39.4) 1/2 SS-8--6-M 1.84 (46.7) 3/4 SS M 2.44 (62.0) 1 SS M 2.59 (65.8) F Ni SS u 0.87 (22.1) 3/8 15/16 1 5/ (620) (771) 3700 (254) 7200 (496) ➀ components with fixed threads must remain stationary during installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts. ➁ Not designed for gasket retainer assembly. Male Reducing Union ➀ 1 1 F Ni SS u /4 1/8 SS-4--6-M-2➁ (34.8) /2 1/4 SS-8--6-M-4 (43.4) 15/16 ➀ components with fixed threads must remain stationary during installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts. ➁ Not designed for gasket retainer assembly. Male ulkhead Union➀ F 1 flat 1/4 1/2 F F 1 Hole ia Panel SS (56.6) (33.0) 3/4 3/4 SS-4--61S (46.2) (25.1) SS (65.3) (37.6) SS-8--61S 2.14 (54.4) 1.11 (28.2) 1 1/16 1 1/16 19/32 (15.0) 29/32 (23.1) Max Panel Thickness Ni SS u (11.2) 0.13 (3.3) 0.50 (12.7) 0.13 (3.3) ➀ components with fixed threads must remain stationary during installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts. utt Weld ulkhead onnector ➀ 1 1 F Panel Hole ia Max Panel Thickness Ni SS u LV T7 (59.9) (33.0) /32 (11.2) 1/4 1/4 3/ (5.6) (15.0) LV-4--61S-4T7 (49.5) (25.1) (3.3) ➀ components with fixed threads must remain stationary during normal installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts.
11 Metal Gasket Face Seal Fittings 11 odies oupling port 1/8 SS-2--G 0.66 (16.8) 7/16 1/4 SS-4--G 1.19 (30.2) 3/4 1/2 SS-8--G 1.31 (33.3) 1 1/16 3/4 SS-12--G 1.68 (42.7) 1 1/2 1 SS-16--G 2.04 (51.8) 1 3/4 F Female Reducing Union ➀ ports F Y Ni SS u Y 1/4 1/8 SS-4--6-F (29.5) 1/2 1/4 SS-8--6-F (35.8) 0.13 (3.3) 3/4 1 1/ (9.1) 0.35 (8.9) ➀ components with fixed threads must remain stationary during normal installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts. Reducing dapter ➀ port Y /8 1/4 SS F➁ (30.2) /4 1/2 SS F (35.8) F Y Ni SS u 3/4 1 1/ (17.5) 0.85 (21.6) ➀ components with fixed threads must remain stationary during normal installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts. ➁ Not designed for gasket retainer assembly. Reducing ushing ➀ port F Y Ni SS u Y 1/4 1/8 SS F 1.06 (26.9) 1/2 1/4 SS F 1.41 (35.8) 0.13 (3.3) 15/ (19.3) 0.91 (23.1) ➀ components with fixed threads must remain stationary during normal installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts. Male NPT lbow ➀ NPT 1/8 1/4 SS /4 1/4 SS /8 1/2 SS /2 1/2 SS F Ni SS u 1.07 (27.2) 1.07 (27.2) 1.45 (36.8) 1.45 (36.8) 0.87 (22.1) 1.05 (26.7) 1.26 (32.0) 1.45 (36.8) 0.38 (9.6) 0.56 (14.2) 0.56 (14.2) 1/2 1/2 13/16 13/16 ➀ components with fixed threads must remain stationary during normal installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts.
12 12 Metal Gasket Face Seal Fittings odies Union lbow ➀ F Ni SS u 1/8 SS-2--9➁ 0.89 (22.6) 1/4 SS (27.2) 1/2 SS (36.8) 3/4 SS (48.8) 1 SS (50.8) 0.87 (22.1) 7/16 1/2 13/16 1 1/4 1 11/ (620) (771) 3700 (254) 7200 (496) ➀ components with fixed threads must remain stationary during normal installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts. ➁ Not designed for gasket retainer assembly. Union Tee ➀ F Ni SS u 1/8 SS-2--T➁ 1.78 (45.2) 1/4 SS-4--T 2.14 (54.4) 1/2 SS-8--T 2.90 (73.7) 3/4 SS-12--T 3.84 (97.5) 1 SS-16--T 4.00 (102) 0.89 (22.6) 1.07 (27.2) 1.45 (36.8) 1.92 (48.8) 2.00 (50.8) 0.87 (22.1) 7/16 1/2 13/16 1 1/4 1 11/ (620) (771) 3700 (254) 7200 (496) ➀ components with fixed threads must remain stationary during normal installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts. ➁ Not designed for gasket retainer assembly. Union ross ➀ F Ni SS u 1/8 SS-2--S➁ 1.78 (45.2) 1/4 SS-4--S 2.14 (54.4) 1/2 SS-8--S 2.90 (73.7) 3/4 SS-12--S 3.84 (97.5) 1 SS-16--S 4.00 (102) 0.89 (22.6) 1.07 (27.2) 1.45 (36.8) 1.92 (48.8) 2.00 (50.8) 0.87 (22.1) 7/16 1/2 13/16 1 1/4 1 11/ (620) (771) 3700 (254) 7200 (496) ➀ components with fixed threads must remain stationary during normal installation. These fitting connections should be assembled only to glands with rotating male or female threaded nuts. ➁ Not designed for gasket retainer assembly.
13 Metal Gasket Face Seal Fittings 13 Welded ssemblies G flat port Male NPT onnector NPT 1/8 1/4 SS-4-W-1-2 1/4 1/4 SS-4-W-1-4 3/8 1/2 SS-8-W-1-6 1/2 1/2 SS-8-W-1-8 F G Ni SS u 1.58 (40.1) 1.79 (45.5) 1.89 (48.0) 2.09 (53.1) 0.38 (9.6) 0.56 (14.2) 0.56 (14.2) 0.95 (24.1) 0.92 (23.4) 1.00 (25.4) 1.01 (25.6) 7/16 3/4 9/16 3/4 11/16 1 1/16 7/8 1 1/16 Female NPT onnector port NPT F G Ni SS u G flat 1/4 1/4 SS-4-W-7-4 3/8 1/2 SS-8-W-7-6 1/2 1/2 SS-8-W (45.0) 1.95 (49.5) 2.18 (55.4) 0.92 (23.4) 1.06 (26.9) 1.04 (26.4) 3/4 3/4 7/8 1 1/16 1 1/16 1 1/ (454) 6600 (454) 5200 (358) Swagelok Fitting onnector port G 1 flat F G G 1 Ni SS u G flat 1/4 1/4 SS-4-W /8 1/4 SS-4-W /2 1/2 SS-8-W (49.3) 1.97 (50.0) 2.23 (56.6) 0.70 (17.8) 0.76 (19.3) 0.86 (21.8) 0.60 (15.2) 0.66 (16.8) 0.90 (22.9) 1/2 3/4 9/16 3/4 11/ (447) 13/16 1 1/16 7/ (447) 5200 (358),, and are typical finger-tight. Swagelok nuts and ferrules are provided assembled, as shown. For tubing maximum pressure ratings for use with Swagelok tube fittings, see Swagelok Tubing ata, MS Rotating Female Union ports G Ni SS u G flat G flat 1/4 SS-4-W-6-F 1.71 (43.4) 1/2 SS-8-W-6-F 1.84 (46.7) 3/4 1 1/16 lbows, crosses, Micro-Fit fittings, and tees are available with welded male and female ends. For more information, contact your authorized Swagelok sales and service representative. Female lbow port 1.00 (25.4) Female Tee 1.00 (25.4) port number: 6LV-4-W-9-F number: 6LV-4-W-T-FFF
14 14 Metal Gasket Face Seal Fittings Nuts, aps, and Plugs port Female Nut F 1/8 SS /4 SS /2 SS-8--1 SS /4 SS SS (13.5) 0.81 (20.6) 0.88 (22.4) 0.88 (22.4) 1.12 (28.4) 1.34 (34.0) 7/ (5.3) 3/ (9.1) 1 1/ (15.5) 1 3/ (18.8) 1 1/ (22.6) 1 3/ (30.5) ap with Lanyard Lanyard material is 302 SS. Lanyard length is 6 in. (15.2 cm). 1/4 SS-4--P-P 0.94 (23.9) 1/2 SS-8--P-P 1.01 (25.6) Plug F (11.2) 0.45 (11.4) 3/4 1 1/16 Male Nut F F /8 SS /8 (12.7) 1/4 SS-4--4➀ 0.71 (18.0) 1/2 SS-8--4 SS /4 SS SS (20.6) 0.81 (20.6) 1.00 (25.4) 1.19 (30.2) 0.21 (5.3) 0.36 (9.1) 15/ (15.5) 1 1/ (18.8) 1 5/ (22.6) (30.5) ➀ taper at the hex end allows the nut to move around 90 tube bends. Short Male Nut For use with short gland. 1/4 F SS N 0.54 (13.7) SS N 0.65 (16.5) 0.36 (9.1) 1/8 SS-2--P➀ 0.68 (17.3) 3/8 1/4 SS-4--P➁ 0.92 (23.4) 1/2 SS-8--P 1.08 (27.4) 15/16 3/4 SS-12--P 1.43 (36.3) 1 5/16 1 SS-16--P 1.52 (38.6) 1 ➀ Not designed for gasket retainer assembly. ➁ lso available as a rotatable plug. number: SS-4--RP Plug with Lanyard Lanyard material is 302 SS. Lanyard length is 6 in. (15.2 cm). 1/4 SS-4--P 0.92 (23.4) 1/2 SS-8--P 1.08 (27.4) F 15/16 ap port F 1/8 SS-2--P 0.63 (16.0) 1/4 SS-4--P 0.94 (23.9) 1/2 SS-8--P 1.01 (25.6) 3/4 SS-12--P 1.29 (32.8) 1 SS-16--P 1.54 (39.1) 0.30 (7.6) (11.2) 7/16 3/ /16 (11.4) 0.54 (13.7) 0.63 (16.0) 1 1/2 1 3/4
15 Metal Gasket Face Seal Fittings 15 Nuts, aps, and Plugs Split-Nut ssemblies Female Male Split Nut Type 1/4 Female SS-4--1-SN 3/ (9.1) 1/4 Male SS-4--4-SN 0.36 (9.1) Material is S (20.6) 0.60 (15.2) 0.63 (16.0) 0.68 (17.4) High-Flow onnections H Type H Type connections are compatible with 1/4 in. connections and are designed for use with Swagelok high-flow diaphragm valves and gas regulators. For uniform flow, use 1/4 in. sideload retainer style gasket. See page 17. Glands utt Weld Nominal Wall Thickness 1 Ni SS u 1 3/ /4 6LV-4-H-3-.60SR 6LV-4-H SR 6LV-4-H SR 0.60 (15.2) 1.19 (30.2) 1.31 (33.3) 0.41 (10.4) 1.00 (25.4) 1.12 (28.4) 0.31 (7.9) odies utt Weld 1 F Ni SS u 1 3/8 1/4 6LV-4-H-1-6T (42.7) 0.31 (7.9) utomatic Weld 1 3/8 1/4 316L-4-H (43.4) 1 F Ni SS u 0.03 (0.8) 0.31 (7.9) 0.41 (10.4)
16 16 Metal Gasket Face Seal Fittings High-Flow onnections H Type odies ulkhead onnector F 1 flat 1 1 F F 1 Hole ia Panel Max Panel Thickness Ni SS u 3/8 1/4 6LV-4-H-61-6T (59.9) 1.30 (33.0) 0.31 (7.9) 3/4 3/4 19/32 (15.0) (11.2) Union lbow F Ni SS u 1/4 SS-4-H (27.2) 1/2 Union Tee F Ni SS u 1/4 SS-4-H-T 2.14 (54.4) 1.07 (27.2) 1/2 Nuts Female port F 1/4 SS-4-H-1SR SS-4-H (20.6) 3/ (9.9) 0.46 (11.7) Male /4 SS-4-H-4SR (18.0) F 0.39 (9.9)
17 Gaskets Information Specify gasket material by adding a material designator to the basic ordering number. Material esignator xample Nickel NI NI-4--2-VS 316L stainless steel SS SS-4--2-VS opper U➀ U-4--2 Nickel and copper gasket retainer assemblies use a 316 stainless steel retainer. ➀ opper gaskets are unplated. However, to order, add U to a basic ordering number for silver-plated gaskets. xample: U Side-load retainer style gaskets are not available in copper. Options Metal Gasket Face Seal Fittings 17 lind Gaskets lind (undrilled) gaskets are available in nonretained and retainer assembly styles. lind gaskets have a maximum differential pressure rating ( p) of 100 psi (6.8 bar). To order, add -L to a basic ordering number. xample: SS-4--2-VS-L Snubber Gaskets Snubber gaskets in 0.5 to 60 µm sizes for 1/4 through 1 in. fittings are available. ontact your authorized Swagelok representative for more information. Silver Plated Unplated (VS) Nonretained annot be used in a gasket retainer assembly (0.7) asic 1/ / / / (5.6) (11.2) 0.58 (14.7) 0.66 (16.8) 0.89 (22.6) 0.26 (6.6) 0.47 (11.9) 0.78 (19.8) 0.91 (23.1) 1.14 (29.0) 1.40 (35.6) Nonretained (0.7) asic 1/ VS 1/ VS 1/ VS VS 3/ VS VS 0.22 (5.6) (11.2) 0.58 (14.7) 0.66 (16.8) 0.89 (22.6) 0.26 (6.6) 0.47 (11.9) 0.78 (19.8) 0.91 (23.1) 1.14 (29.0) 1.40 (35.6) Gasket Retainer ssembly Retainer and gasket must be used as an assembly (0.7) asic 1/ GR 0.24 (6.1) 1/ GR (11.2) 3/ GR 0.66 (16.8) GR 0.89 (22.6) 0.50 (12.7) 0.79 (20.1) 1.14 (29.0) 1.40 (35.6) Gasket Retainer ssembly (0.7) asic 1/ GR-VS 0.24 (6.1) 1/ GR-VS (11.2) 3/ GR-VS 0.66 (16.8) GR-VS 0.89 (22.6) 0.50 (12.7) 0.79 (20.1) 1.14 (29.0) 1.40 (35.6) Side-Load Retainer (0.7) asic 1/ Z-VS 1/ Z-VS 0.24 (6.1) 0.43 (11.0) 0.45 (11.4)
18 18 Metal Gasket Face Seal Fittings Flow Restrictors This product can be used in liquid or gas delivery systems where repeatable flow reduction or limiting is required. One piece, compact design saves space Standard orifice sizes drilled through a 1/4 in. male union No dead volume for clean operation Identification of orifice and heat code marked clearly on the body lectropolished, cleaned, and packaged in accordance with Swagelok Ultrahigh-Purity Process Specification (S-01), MS Working pressure psig (689 bar) Information and x 1.55 (39.4) in. flat x, in. (mm) (4) 6LV-4--6-M-010P (0.305) 6LV-4--6-M-012P (0.381) 6LV-4--6-M-015P (0.432) 6LV-4--6-M-017P (0.508) 6LV-4--6-M-020P (0.584) 6LV-4--6-M-023P (0.635) 6LV-4--6-M-025P (0.660) 6LV-4--6-M-026P (0.686) 6LV-4--6-M-027P (0.762) 6LV-4--6-M-030P (0.889) 6LV-4--6-M-035P (1.016) 6LV-4--6-M-040P (1.143) 6LV-4--6-M-045P components with fixed threads must remain stationary during normal installation. These fitting connections should be assembled only to glands with rotating female nuts. x, in. (mm) (1.270) 6LV-4--6-M-050P (1.397) 6LV-4--6-M-055P (1.529) 6LV-4--6-M-060P (1.651) 6LV-4--6-M-065P (1.778) 6LV-4--6-M-070P (1.905) 6LV-4--6-M-075P (2.032) 6LV-4--6-M-080P (2.159) 6LV-4--6-M-085P 0 (2.286) 6LV-4--6-M-090P 3 (2.362) 6LV-4--6-M-093P 5 (2.413) 6LV-4--6-M-095P (2.540) 6LV-4--6-M-100P Lock and Tag evices These devices help prevent unintentional disassembly of connections. dditionally, both devices include a wire hole to allow for a tag to support identification and quality verification programs. Fitting Lock evice This device is intended for use on Swagelok metal gasket face seal assemblies with standard male and female nuts. 1/4 in. SS-4--FL 1/2 in. SS-8--FL Fitting Lock evice for Valves This device is intended for use on Swagelok valves with integrally machined male metal gasket face seal end connections. Side-Load Installation Tool and Tray Tool Makes gasket handling easy, preserves cleanliness nables gasket installation where space is limited Is used to easily remove gasket from storage tray Material: Polyethersulfone (PS) Tray (includes 30 gaskets; order in multiples of 30) Keeps gaskets secure Keeps gaskets aligned for easy removal with side-load gasket tool leaned and packaged in accordance with Swagelok Ultrahigh-Purity Process Specification (S-01), MS Material: Tray polypropylene Lid polycarbonate Valve Series L3, L3T, N4, L, S, P, PH, H, 4K, 1/4 in. 4MG, 4MRG, 4MW, 4MRW, 4UG, 4UK SS-4--VL escription Installation tool Tray (nickel gaskets) Tray (SS gaskets) MS-4--Z-TL NI-4--2-ZT-VS SS-4--2-ZT-VS 1/2 in. 8G, 8K, 8UG, 8UK, 8UW SS-8--VL For fitting lock devices for valves not listed, contact your authorized Swagelok representative.
19 Fitting Installation Instructions Metal Gasket Face Seal Fittings GTW 2 3 GTW 7 Finger-tight 4 8 1/8 turn SS, Ni 5 1/4 turn u 5a 5b 5c
20 Split-Nut Installation Instructions Male Female Swagelok Orbital Welding System See the Swagelok Welding System M200 Power Supply catalog, MS , for more information. Safe Product Selection When selecting a product, the total system design must be considered to ensure safe, trouble-free performance. Function, material compatibility, adequate ratings, proper installation, operation, and maintenance are the responsibilities of the system designer and user. aution: o not mix or interchange parts with those of other manufacturers. Warranty Information Swagelok products are backed by The Swagelok Limited Lifetime Warranty. For a copy, visit swagelok.com or contact your authorized Swagelok representative. Swagelok,, Micro-Fit TM Swagelok ompany Swagelok ompany Printed in U.S.., GS February 2015, R15 MS-01-24
Compact, High-Flow Gas Regulators
www.swagelok.com Compact, High-Flow Gas Regulators HF Series Precise pressure control Tamper-free design High-purity design Preset and adjustable dome-loaded models 2 Compact, High-Flow Gas Regulators
More informationMultipurpose Ball Valves
www.swagelok.com Multipurpose Ball Valves 33 Series Working pressures up to 6000 psig (413 bar) High flow capacity in a compact design Available with PEEK and UHMWPE seats Variety of end connections Low
More informationStainless Steel Valves For the Sanitary Industries
www.swagelok.com Stainless Steel Valves For the Sanitary Industries Sanitary ball valves Manual and pneumatically actuated butterfly valves Disk and ball check valves ir blow check valves ir relief valves
More informationCajon VCR Fittings. Flanges, Fittings, & Components. Cajon & Swagelok Fittings. Cajon VCR Fittings. Nuts, Caps, & Plugs. Socket Weld Glands
Cajon VCR Fittings Cajon VCR Fittings Make excellent low-pressure gas connections Ideal for lecture bottle gas cylinders, standard helium checks, and general gas plumbing Withstand bakeout to 58º C (with
More informationFittings, Tubing & Nipples
s, Tubing & Nipples P Series Pipe s s to 15,000 psi (1034 bar) Since 1945 Parker utoclave Engineers has designed and built premium quality valves, fittings and tubing. This commitment to engineering and
More informationProportional Relief Valves
www.swagelok.com Proportional Relief Valves R Series Liquid or gas service Set pressures from 10 to psig (0.7 to 413 bar) 1/4 and 1/2 in. and 6 to 12 mm end connections 2 Proportional Relief Valves Spring
More informationFITTINGS 5-01. 82A series Aluminium (light weight) compression fittings Ø 6... 42 mm tube size, BSPP and BSPT thread
FITTINS 82 series luminium (light weight) compression fittings Ø 6... 42 mm tube size, SPP and SPT thread 82 series rass compression fittings Ø 6... 42 mm tube size, SPP and SPT thread 83 series luminium
More informationPipe threads for tubes and fittings where pressure-tight joints are not made on the threads. (requires PTFE sealing tape or liquid sealant).
Fittings for CO 2 Pipe Threads Pipe thread references quoted in this catalogue conform with the requirements specified in the latest issue and amendments of the following ISO Standards: ISO 7-1 (BS21)
More informationPTU Series Ultrahigh-Purity Pressure Transducers
PTU Series UltrahighPurity Pressure Transducers User s Manual The Swagelok PTU series pressure transducer provides electronic monitoring of system pressure for ultrahighpurity applications. The PTU series
More informationTY-FLO Needle Valves
Design/Features Hard (Vee) or Delrin Soft Seat/Tip Orifice sizes from.17 to.438 in. Flow Coefficients (C V ) from.37 to.7 Straight or angle flow patterns Optional panel mount Handle options available Non-wetted
More informationNeedle Valves. NB, NBH, ND, NDH, NF, NFH, NG, NGH, NR, NRG, NT, NU, NUH, NY and NYH Series. www.fitokgroup.com
Needle Valves NB, NBH, N, NH, NF, NFH, NG, NGH, NR, NRG, NT, NU, NUH, NY and NYH Series www.fitokgroup.com ontents Bar Stock Needle Valves NB Series and NBH Series Nonrotating-stem Needle Valves N Series
More informationFRL/AirCare Air Controls & Accessories
FRL/irare ir ontrols & ccessories Lincoln Regulators, Filters & Lubricators well-planned compressed air system ensures minimum pressure loss in the system, and the removal of contaminants: water, compressor
More informationHose and Flexible Tubing
www.swagelok.com and Flexible Tubing ssemblies, ulk, Flexible Tubing, and s Core materials include metal, PTFE, PF, vinyl, nylon, polyethylene, and rubber hose sizes 1/8 to 2 Wide range of fractional and
More informationLimit Switches/ Receptacle Assembly... For Nuclear Environments
180-302/402 Series Inside ontainment reas TM Limit Switches/ Receptacle ssembly... or Nuclear nvironments eatures: Qualified to I s 344-1975, 323-1974, and 382-1972. Manufactured to a quality assurance
More informationGAS DISTRIBUTION PRODUCTS STEEL SERVICE TEES
GAS DISTRIBUTION PRODUCTS STEEL SERVICE TEES CONTINENTAL INDUSTRIES ABOUT US THE ULTIMATE CONNECTION Our Company Continental Industries, headquartered in Tulsa, Oklahoma, was formed in 1958 and is today
More informationRated Burst Pressure 200 Series: 2.5 : 1 H200 Series: 4 : 1
200 Series 0 to 3000 psig heck Valves H200 Series 0 to 6000 psig heck Valves Features & enefits Quick opening/positive closing Provides a wide range of adaptability Large flow capacity The patented sealing
More informationGaugeable Tube Fittings and Adapter Fittings
www.swagelok.com Gaugeable Fittings and dapter Fittings vailable in tube sizes from / to 2 and 2 to 50 mm Consistent gaugeability upon initial installation asy to disconnect and retighten Wide variety
More informationFittings and Tubing. Low Pressure. Fittings and Tubing - Low Pressure. Low Pressure Fittings and Tubing Features: Pressures to 15,000 psi (1034 bar)
ittings and Tubing - Low Pressure ittings and Tubing Low Pressure Pressures to 15,000 psi (1034 bar) Since 1945 utoclave ngineers has designed and built premium quality valves, fittings and tubing. This
More informationSevere-Ser vice Union-Bonnet Needle Valves
www.swagelok.com Severe-Ser vice Union-onnet Needle Valves N Series and N Series Working pressures up to 10 000 psig (689 bar) Temperatures from 65 to 450 F ( 53 to 232 C) with PTFE packing; up to 1200
More informationNeedle Valves. Needle Valves Part Matrix. Flow Coefficient (C v ) belgas.net < 129 >
Needle Valves elgs Standard Needle Valves offer four choices in 316 stainless steel as well as one piece forged carbon plated steel; soft seat and hard seat, angle and globe styles. The Mini Valve offers
More informationFlare Fittings. The World Standard. SAE 45 Flared Fittings... D4. Inverted Flared Fittings... D14. Access Valves... D18
Flare Fittings SAE 45 Flared Fittings... 4 Inverted Flared Fittings... 14 Access Valves... 18 The World Standard Flare Fittings Flare to ale PT 48F ale Connector 481FH ale Connector AVU1 ale Connector
More informationCheck Valves & Actuated Valves
heck Valves & ctuated Valves & U Series Piston non-return valves rated 6,000 psi & 10,000 psi X Series Piston non-return valves rated 20,000 psi Pneumatic ctuators Pneumatically actuated valves Electric
More informationFittings, Tubing & Nipples
Fittings, Tubing & Nipples High Pressure Pressures to 150,000 psi (10342 bar) Since 1945 Parker utoclave Engineers has designed and built premium quality valves, fittings and tubing. This commitment to
More informationball valves Flomite 71 Series 2-way Integral Panel Mount Ball Valves
2-way Integral Panel Mount Ball Valves Used for quick on-off service with a visual indication of flow, HOKE s 2-way ball valves offer orifice sizes up to 0.25 (6.4mm). Flomite valves feature a floating
More informationThese features have made Lo Torc valves the choice of high pressure plug value users, worldwide:
LO TORC Plug Valve The high value, dependable performance, and low maintenance requirements of Halliburton Lo Torc valves can help reduce overall operating costs and help cut downtime. These features have
More informationFittings, Tubing & Nipples
Fittings,Tubing & Nipples - Medium Pressure Fittings, Tubing & Nipples Medium Pressure Pressures to 20,000 psi (1379 bar) Since 1945 utoclave Engineers has designed and built premium quality valves, fittings
More informationBaumann 87000 Flexsleev Sanitary Control Valve
Product Bulletin D103345X012 Baumann 87000 Flexsleev Sanitary Control Valve The Baumann 87000 control valve (figures 1 and 2) is excellent for throttling high purity liquid or gaseous media commonly found
More informationneedle valves Needle Valves Index At a Glance 1
Needle Valves Index At a Glance 1 1700 Series 5 Forged Body, Integral Bonnet Needle Valves 2100 Series 8 Bar Stock, Screwed Bonnet Needle Valves 2200 Series 12 Bar Stock, Screwed Bonnet Needle Valves 2219
More informationSeries M Applicable Tubing: ø2 Connection Thread: M3, M5
iniature Fittings Series pplicable Tubing: ø2 onnection Thread:, RoHS ade to Order (Refer to page for details.) pplicable O.D. x I.D.: ø2 x ø.2 onnection thread: / One-touch fitting size: ø.2 / ø Tubing
More informationFittings, Tubing & Nipples
Fittings, Tubing & Nipples Medium Pressure Pressures to 20,000 psi (1379 bar) Since 1945 utoclave Engineers has designed and built premium quality valves, fittings and tubing. This commitment to engineering
More informationVe-Lock manufactures Needle Valves from Solid bar stock Materials & all parts details are as below:
Needle Valves : - Needle valves have a slender, tapered point at the end of the valve stem that is lowered through the seat to restrict or block flow. Fluid flowing through the Needle valve turns 90 degrees
More informationThread and End Connection
www.swagelok.com and End Connection Identification Guide 2 Contents Introduction and End Connection Terminology.. 4 General Terminology... 5 Step-by-Step Identification Procedure for s and End Connections...
More informationPipe Valves, Fittings and Nipples Pressures to 15,200 psi
Pipe Valves, Fittings and Nipples MAXIMATOR has been designing and manufacturing high pressure equipment for more than thirty years and has a worldwide reputation for quality and reliability, backed by
More informationVariable Area Flowmeters
www.swagelok.com Variable Area Flowmeters G Series and M Series Glass and metal (armored) tube models, including miniature armored model Highly accurate measurement with individually calibrated scales
More informationHigh Pressure Equipment High Pressure Valves, Fittings and Tubing
igh quipment igh Valves, ittings and Tubing 0,000, 40,000 and psi service igh quipment Company has developed a line of igh products to assure safe and easy plumbing for 0,000, 40,000 and psi. These needle
More information60.12. Depend-O-Lok FxE Expansion Coupling. System No. Submitted By Spec Sect Para Location Date Approved Date. DEPEND-O-LOK FxE EXPANSION COUPLING
60.1 D-O-L FxE expansion couplings are a bolted, split-sleeve design that provides for expansion and contraction at the coupled joint. These couplings are furnished with restraint rings that, when affixed
More informationSubmersion/Insertion Toroidal Sensor
Instruction Sheet PN 51A-228/rev.P December 2010 Model 228 Submersion/Insertion Toroidal Sensor For additional information, please visit our website at www.emersonprocess.com/raihome/liquid/. CAUTION SENSOR/PROCESS
More informationTYPE E Main Valve Sizes 3 /8 through 12
SD 3001F PRINTED IN U.S.A. SD 3001F/0707 A B TYPE E MAIN VALVE C D E TYPE E Main Valve Sizes 3 /8 through 12 The Spence Type E Main Valve is of normally closed, single seat design featuring packless construction,
More informationMicrowave Components. J & N Microwave and Engineering. Product Catalogue 2010 Version 2.0
Product Catalogue 2010 Version 2.0 Contents Contact Details i Waveguide Loads/Terminations 1 Low Power Short Waveguide Terminations 2 Medium Power Short Waveguide Terminations 3 Higher Power Waveguide
More informationTubing Data. Contents. Tubing Selection. Tubing Handling. Tubing Material. Tubing Outside Diameter Hardness. Tubing Wall Thickness
www.swagelok.com Tubing Data Contents Tubing Selection... 1 Tubing Handling.... 1 Gas Service... 2 Tubing Installation.... 2 Suggested Allowable Working Pressure Tables Carbon Steel Tubing... 3 Stainless
More informationStainless Steel Single and Dual Circulation Kits
Instruction Sheet P/N 160780 01 Stainless Steel Single and Dual Circulation Kits Introduction The single and dual high-pressure circulation kits allow you to vary and control the circulation rate of coating
More informationCaps STANDARD WEIGHT Inches / Pounds
Standard Caps you are here: Home > Weldbend Catalog > Fittings > Caps Caps STANDARD WEIGHT Inches / Pounds For Metric Units >Click Here Nominal Pipe Size Outside Inside Wall Thickness (T) Length (E) Pipe
More informationNEW SIX-SEALS CUTTING RING. INTERNATIONAL INDUSTRIAL PATENT Nr. 864061 of the 10/03/99 FLANKS AND DOES NOT REPLACE THE STANDARD RING CURRENTLY IN USE
B4 NEW SIX-SEALS CUTTING RING. INTERNATIONAL INDUSTRIAL PATENT Nr. 864061 of the 10/03/99 FLANKS AND DOES NOT REPLACE THE STANDARD RING CURRENTLY IN USE AVAILABLE IN CARBON AND STAINLESS STEEL 23 THEORY
More informationMultijacketed Tubing, Single-Jacketed Tubing, and Insulated Tubing
www.swagelok.com Multijacketed Tubing, Single-Jacketed Tubing, Insulated Tubing Features 1/4 to 6 to 12 tubing sizes available in 316/316L stainless steel copper Seamless welded tubing available in stainless
More informationFittings, Tubing & Nipples
Fittings, Tubing & Nipples High Pressure Pressures to 150,000 psi (10342 bar) Since 1945 utoclave Engineers has designed and built premium quality valves, fittings and tubing. This commitment to engineering
More informationJames M. Pleasants Company
James M. Pleasants Company SUBMITTAL DATA GAINESVILLE MECHANICAL DECEMBER 20, 2013 PROJECT: GSU: J-183 HUMANITIES LAW BLDG. QUOTE NO:12116 ENGINEER: STEVENS & WILKINSON GASKETED PLATE HEAT EXCHANGER Tag:
More informationSevere-Service Union-Bonnet Needle Valves
www.swagelok.com Severe-Service Union-Bonnet Needle Valves N Series and HN Series Working pressures up to 10 000 psig (689 bar) Temperatures from 65 to 450 F ( 53 to 232 C) with PTFE packing; up to 1200
More informationHome. News. Products. Contact Us. Treated Swagelok Fittings--for better inertness!
New GC Accessories New GC Accessories New GC Accessories Fittings: Swagelok : Home Brass & Stainless Steel News Also available: Products Silco Fittings : Siltek & Sulfinert Also available: Info & Support
More informationHose and Tube Fittings Series 1-3
Embracing Challenge Hose and Tube Fittings Series 1-3 out of plastics PP, PVDF, PTFE Series 1 Special Features Corrosion resistant Gas tight Easy to handle Different connection threads Application Hose
More informationGYROLOK to Tube Union
GYROLOK HOKE manufactured GYROLOK tube fittings have been carefully designed and manufactured to provide a wide range of outstanding leak-tight application capabilities. GYROLOK to Tube Union MANUFACTURED
More informationBaumann 24003 3 Way Bronze or Stainless Steel Control Valve
Product Bulletin D1039X012 24003 Valve Baumann 24003 3 Way Bronze or Stainless Steel Control Valve 3 Way Rugged Industrial Control Valve For Mixing and Diverting Applications The Baumann 24003 3 way control
More informationMany Products...One Source
PRESSURE GAUGES Dedicated Sales Rep for Your Area 97%Fill Rate Shipping within 24 Hours State of the Art Warehouse System Technical Support Quality Control Program 25 Whaley Avenue Milverton, Ontario N0K
More informationHose Clamps & Fittings
All Stainless Steel Marine or Underground Hose Clamps 5/16 HEX HEAD SCREW 60000 SERIES Highly corrosion resistant Use for marine or underground applications Stainless Steel Band, Housing Plated Steel Screw
More informationNow Available in Black Zinc Nickel
847/848 Series Power Supply up to 63 Now vailable in lack Zinc Nickel The 847/848 bayonet Series has been especially designed for light and harsh environment. Its physical characteristics and performances
More informationStream Selector System
www.swagelok.com Selector System For Process Analyzer Applications SSV Series Provides double-block-and-bleed (DBB) operation in a single compact module Conventional NPT and ANSI/ISA 76.00.02 compatible
More informationSolenoid valves 2/2-way direct-operated Type EV210A
Solenoid valves 2/2-way direct-operated Type EV210A Features EV210A NC and NO Very compact valves for industrial application, such as control and dosage For water, oil, compressed air and similar neutral
More informationDuolok Tube Fittings QUALITY INSTRUMENTATION FITTINGS. Made in USA. www.sspfittings.com
Made in US uolok ube Fittings www.sspfittings.com QULIY INSRUMNION FIINS 1 SSP Fittings orp. / SSP Instrumentation able of ontents How to Order... 3 ube Fittings Selection uide... 4-6 uolok ube Fittings
More informationSERIES ASM NEOPRENE/EPMD FLANGED SINGLE SPHERE CONNECTOR CONNECTORS. Pressures to 225 PSIG (15.51 barg) Temperatures to 230ºF (110ºC)
APPLICATIONS Process Industry Weak Acids Alkalies Compressed Air Pulp & Paper MODELS ASM - Flanged Connection OPTIONS Control Rods Oil & Gas Water & Waste Pump suction & discharge Sea water Chemical lines
More informationMass Flow Meters & Controllers
HFM-D-3A & 305A Mass Flow Meters HFC-D-3A & 307A Mass Flow Controllers FEATURES Range 0-25 slm to 0-2500 slm (N 2 Equivalent) Excellent Accuracy ±(0.5% of Reading + 0.2% of Full Scale) 0-5 VDC or 4-20
More informationQuick Connect. RTDs, Cordsets and Transmitter with M12 Connections
Quick Connect RTDs, Cordsets and Transmitter with M12 Connections 1 Temperature Measurement Experts Since 1960, urns Engineering has been an industry leader in the design and manufacture of temperature
More informationMIL-PRF-39012 QPL Connectors MIL-PRF-55339 QPL Adapters Online Catalog Volume 1
MIL-PRF-39012 QPL onnectors MIL-PRF-55339 QPL dapters Online atalog Volume 1 Delta QPL connectors and adapters meet or exceed all requirements of MIL-PRF-39012 and MIL-PRF-55339. ecause these specifications
More informationProduct Manual. CVS Type 67AFR Filter Regulator. Introduction. Installation. Description
Product Manual CVS Type 67AFR Filter Regulator Introduction This CVS Controls product manual includes instructions for the installation, adjustment, maintenance and parts ordering of the CVS Type 67AFR
More informationMueller. Pipe Repair Products. Saddles Tapping Sleeves Pipe Repair Clamps A complete selection for all types of pipe... all from a single source.
Mueller Pipe Repair Products Saddles Tapping Sleeves Pipe Repair Clamps A complete selection for all types of pipe... all from a single source. SERVICE SADDLES Mueller service saddles, available in bronze,
More informationSTC 3S012-020-A Series Solenoid Valves
STC 3S012-020-A Series Solenoid Valves 3S012-020-A Series Solenoid Valve Specifications Valve Model 3S012-1/8-A 3S012-1/4-A 3S020-1/8-A 3S020-1/4-A Port Size (NPT) 1/8 1/4 1/8 1/4 Valve Type Action 3 Way,
More information37 JIC Flare (Nuts) 304C (070112) 306 (070118) 318 (070110) Pg. 22-75-160 Bulkhead Locknut (Use with #2700) Pg. 23 Tube Nut (Use with #319)
37 JIC Flare (Nuts) Components Assembled The 37 JIC (Joint Industrial Council) Flare is a reliable, straight thread, single-flare design that is used world-wide. It is popular in many applications and
More informationVolkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 17 Engine-Lubrication system (Page GR-17)
17 Engine-Lubrication system (Page GR-17) Lubrication system components, removing and installing Oil pan, removing and installing Oil pressure and oil pressure switch, checking Dynamic oil pressure warning
More informationComplete Systems & Parts Automatic Oiler & Grease Bank
MADE IN THE USA Complete Systems & Parts Automatic Oiler & Grease Bank www.gosuburban.com 2 Lubrication Systems Lubrication Systems, a division of Suburban Manufacturing, manufactures a complete line of
More informationControl Stations Made of Polyester Resin Series 8146
ontrol Stations Made of Polyester Resin www.stahl.de > s made of glass-fibre reinforced polyester resin > 8 basic enclosure sizes with various enclosure heights > an be combined to larger units > Equipped
More informationBaumann 24000SB Barstock Control Valve
Instruction Manual 24000SB Valve Baumann 24000SB Barstock Control Valve Contents Introduction... 1 Scope of Manual... 1 Safety Precautions... 2 Maintenance... 3 Installation... 3 Air Piping... 4 Disassembly...
More informationReplacement parts. WM97+ gas-fired water boiler Boiler Manual. OBTAIN PARTS ONLY THROUGH WEIL-McLAIN THE BOILER CONTAINS CERAMIC FIBER MATERIALS
Replacement parts DO NOT SERVICE THE BOILER WITHOUT A WM97+ MAINTENANCE KIT AVAILABLE Failure to adhere to these guidelines can result in severe personal injury, death or substantial property damage. The
More informationwww.swagelok.com An Installer s Pocket Guide Tube Fit tings
www.swagelok.com An Installer s Pocket Guide for Swagelok Fit tings CONTENTS Intermixing/Interchanging............... 8 Metric Swagelok Fittings........... 8 Installation Instructions Safety Precautions.......................
More informationKF Needle & Gauge Valves
KF Needle & Gauge Valves Superior Fluid Control Products KF O-Ring & Packed Stem Style Needle Valves KF Needle Valves combine rugged construction, dependability and leak-free performance at high and low
More informationVALVES FOR REFRIGERATING SYSTEMS
VALVES FOR REFRIGERATING SYSTEMS FROM QUALITY OUR NATURAL DEVELOPMENT Achieved the goal of fi fty years working in the industry of Refrigeration and Air Conditioning, Castel Quality Range of Products is
More informationwww.swagelok.com An Installer s Pocket Guide for Swagelok Tube Fittings
www.swagelok.com An Installer s Pocket Guide for Swagelok Fittings 2 CONTENTS Intermixing/Interchanging... 8 Metric Swagelok Fittings... 8 Installation Instructions Safety Precautions... 9 Up to /25 mm
More informationgyrolok tube fittings
The Facts About Interchangeability and Intermixability Index History of HOKE Gyrolok 1 Background 1 Commitment to Customer 1 Intermixability 2 Interchangeability 2 Positions 2 Guarantee 3 Features & Benefits
More information4 Posiflow Proportional Solenoid Valves
4 Posiflow Solenoid Brass or Stainless Steel Bodies 1/4" to 1/2" NPT 2/2 Features Flow rates adjustable between 0% and 100% of rating Flow rate can also be regulated by a range of electrical inputs (sensors,
More informationMueller B-101 and A-3 Drilling and Tapping Machines
TM TM Mueller and Drilling and Tapping Machines A guide to selecting Mueller Equipment Mueller TM TM and Drilling and Tapping Machines When it comes to line stopping and drilling and tapping technology
More information14 PHOENIX CONTACT Courtesy of Power/mation. 1310 Energy Lane, Saint Paul, MN 55108. info@powermation.com - 800-843-9859 - www.powermation.
14 PHOENIX CONTACT PLUSCON circular is a circular connector for use in industrial automation. The range of design sizes available is varied, starting with the design sizes M5 to M8 and M1, for sensor/actuator
More informationDouble-Headed Screw 1. 3/4" FIP x 3/4" MIP x 1/4" hole 2. 3/4" Fip x 3/4" MIP. Feed Water Connector 1. 1/2" FIP x 1/2" MIP x 1/4" OD 2. 3.
Picture Item No. Description RO- 0010 Brass Water Feed 1. 3/4" FIP with 1/4" hole 2. Using on R.O. tank RO- O020 Double-Headed Screw 1. 3/4" FIP x 3/4" MIP x 1/4" hole 2. 3/4" Fip x 3/4" MIP RO- 0030 Brass
More informationToroidal Conductivity Sensor
Instruction Sheet PN 51A-/rev.C June 2012 Toroidal Conductivity Sensor For additional information, please visit our website at www.emersonprocess.com/rosemountanalytical.com SPECIFICATIONS Wetted Materials:
More informationHigh Pressure Equipment Pressure Vessels and Reactors Index
Pressure Vessels and Reacrs High Pressure Equipment Company designs and manufactures a broad range of pressure vessels and reacrs for both bench-scale and pilot plant applications. We have over 0 standard
More informationMTI10 Insertion and MTL10 In-line Thermal Mass Flowmeter and Temperature Transmitter
Thermal Mass meter and Temperature Transmitter Description The MTI10 insertion thermal mass flowmeter and the MTL10 in-line thermal mass flowmeter provide accurate mass flow measurement of clean, dry gases
More informationAMERICAN FITTINGS. Corporation. SPEC-grade. Rigid-IMC Connectors Compression Type - (No Thread)
Connectors / Compression Type Size Range: 1/2 to 5 Rigid-IMC Connectors Compression Type - (No Thread) Industrial specification grade, screw machined steel, zinc plated UL Listed RIN TIGHT and Concrete
More informationUniversal Installation and Maintenance Instructions Double Wall Spill Containment Bucket (5 and 15 gal)
Universal Installation and Maintenance Instructions Double Wall Spill Containment Bucket (5 and 15 gal) IMPORTANT: It is imperative that the user read these warnings and use of the assembly instructions
More informationGEET Fuel Processor Plans
GEET Fuel Processor Plans This is a greatly simplified Proof of Concept version of the GEET Fuel Processor that just about anyone can build from parts from a local Hardware store in a weekend for very
More informationDMP 331. Industrial Pressure Transmitter for Low Pressure. Stainless Steel Sensor
DMP Industrial Pressure Transmitter for Low Pressure Stainless Steel Sensor accuracy according to IEC 60770: standard: 0.5 % FSO option: 0.5 / 0. % FSO from 0... 00 mbar up to 0... 40 bar Output signals
More informationPOSEIDON 2-29, 2-25 & 2-22 POSEIDON 2-29, 2-25 & 2-22 XT
POSEION 2-29, 2-25 & 2-22 POSEION 2-29, 2-25 & 2-22 XT Repair Manual Index A. Safety precautions 3 B. Technical data 4 C. Structure 5-6. Service / Repair 7-23 E. Tools 24 F. Function 25-26 G. Electric
More informationMueller. Pipe Repair Products. A complete selection for all types of gas lines... all from a single source. GAS PRODUCTS DIVISION
Mueller Pipe Repair Products A complete selection for all types of gas lines... all from a single source. GAS PRODUCTS DIVISION MUELLER STAINLESS STEEL REPAIR CLAMPS Mueller offers a full line of stainless
More informationQLM and QLD Series Three-port Control Valves
Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without
More informationPowers Controls TH 192 HC Heating/Cooling Room Thermostat
Powers Controls TH 192 HC Heating/Cooling Room Thermostat Technical Instructions Document No. 155-066P25 TH 192-2 50 60 70 80 70 TH0356R1 60 80 POWERS Description The TH 192 HC thermostats are proportional
More informationGriplok. Tube Fittings. Quality Instrumentation Fittings
ube ittings Quality Instrumentation ittings ompany Information 1926 SSP ittings orp. is founded in leveland, Ohio, U.S.. SSP begins as a contract manufacturer of screw machine products in brass and carbon
More informationInstallation and Operating Instructions Installation Instructions for SS EPE-316L Series
INSTR3010 0406 Installation and Operating Instructions Installation Instructions for SS EPE-316L Series Congratulations on your purchase of this Aqua-Pure high flow, single housing filtration system. This
More informationSelf Purging Liquid Trap (SPLT ) User s Manual
Self Purging Liquid Trap (SPLT ) User s Manual High pressure liquids and gases are potentially hazardous. Energy stored in these liquids and gases can be released unexpectedly and with extreme force. High
More informationFilter/Regulators Compressed air, general purpose, and Instrument Filter/Regulators 1/8" to 1-1/2" port sizes
Section 12 Filter/Regulators Compressed air, general purpose, and Instrument Filter/Regulators 1/8" to 1-1/2" port sizes B7 Miniature eneral Purpose Filter/Regulator 1/8" and 1/" ports...................................le-12-2
More informationFLEXWELL Safety Pipe. Pipe systems for installations Technical details
Pipe systems for installations Technical details Notes 08.04.2013 T page 2 Contents 4.0 4.0 Contents 4.1 System description 4.100 System description FLEXWELL Safety Pipe 4.105 System description FLEXWELL
More information5.2. Overview. The better method to install solderless compression connectors on power cable
5.2 Overview The better method to install solderless compression connectors on power cable The Thomas & Betts method of installing compression connectors on power cables is designed to provide a high degree
More information2 H OW TO ORDER 2 D ESIGN FEATURES 3 P RODUCTS INDEX 35 O VAL FLANGES 35 B LEED 35 C ONDENSING POTS 36 S YPHONS 36 A IR FEED HEADERS
MEK PIPING srl www.mekpiping.com Sede legale/headquarter : Via San Giovanni osco zona P.I.P. Poggiorsini, () 70020 Tel / Fax + 39 080 37063 - Mob. +39 346 3438582 - E-MIL: mekpiping@mekpiping.com P.IV
More informationPowers Controls Free Energy Band TH 193 HC Heating/Cooling Room Thermostat
Document No. 155-068P25 TH 193-4 Powers Controls Free Energy Band TH 193 HC Heating/Cooling Room Thermostat 50 60 70 80 70 TH0356R1 60 80 POWERS Description The TH 193 HC thermostats are proportional dual
More informationOPTIMIZE UPTIME WITH TIMKEN LUBRICATORS
OPTIMIZE UPTIME WITH TIMKEN LURITORS 1 Discover a better way to choose the right lubricators pplying lubrication exactly where and when it s needed will help keep your operations running smoothly. Timken
More informationHYDRAULIC PIPING STANDARD HANDBOOK. Revision 1
HYDRAULIC PIPING STANDARD HANDBOOK Revision 1 Preface We aim to fill a gap in technical literature. At this moment there are no hydraulic piping standards available which cover different pressure classes
More information