CREEK Technical Services, LLC

Transcription

1 EVALUATION REPORT 2010 FLORIDA BUILDING CODE Manufacturer: Henry Company Report Issued February 20, North Sepulveda Blvd., Suite 800 El Segundo, CA (800) Manufacturing Plants: Quality Assurance: Bartow, FL Scarbourgh, Ontario PRI Construction Materials Technologies (QUA9110) SCOPE Category: Roofing Subcategory: Cements-Adhesives-Coatings Code Sections: , , Properties: Material Standards REFERENCES Entity Report No. Standard Year PRI Construction Materials Technologies (TST5878) HGC ASTM D e01 PRI Construction Materials Technologies (TST5878) HGC ASTM D (2007) PRI Construction Materials Technologies (TST5878) HGC ASTM D (2007) PRI Construction Materials Technologies (TST5878) HGC ASTM D (2007) PRI Construction Materials Technologies (TST5878) HGC ASTM D PRI Construction Materials Technologies (TST5878) HGC ASTM D PRI Construction Materials Technologies (TST5878) HGC ASTM D PRI Construction Materials Technologies (TST5878) HGC TAS 114(H) 1995 PRI Construction Materials Technologies (TST5878) HGC ASTM D PRI Construction Materials Technologies (TST5878) HGC ASTM D PRI Construction Materials Technologies (TST5878) HGC ASTM D PRI Construction Materials Technologies (TST5878) HGC TAS PRI Construction Materials Technologies (TST5878) HGC ASTM D (2007) PRI Construction Materials Technologies (TST5878) HGC ASTM D PRI Construction Materials Technologies (TST5878) HGC ASTM D PRI Construction Materials Technologies (TST5878) HGC ASTM D PRI Construction Materials Technologies (TST5878) HGC ASTM D PRI Construction Materials Technologies (TST5878) HGC ASTM D PRI Construction Materials Technologies (TST5878) HGC ASTM D PRI Construction Materials Technologies (TST5878) HGC ASTM D PRI Construction Materials Technologies (TST5878) HGC ASTM D PRI Construction Materials Technologies (TST5878) HGC ASTM D HEN13001 FL10889 Page 1 of 5

2 PRODUCT DESCRIPTION & APPLICATION Unless otherwise noted, all surfaces shall be clean, dry, and free of oil, grease, rust, scale, or other debris prior to application. Unless otherwise noted, coatings are not recommended over gravel, rubber or PVC sheet roofing, shingles of any kind, nor old, dry, brittle roofs unable to withstand shrinkage stresses. Consult product data sheets for detailed application instructions. HE505 FLASHMASTER FLASHING HE906 FLASHMASTER PLUS HE208 WET PATCH TM ROOF LEAK REPAIR HE204 PLASTIC ROOF HE554 GOLD MEDAL MB FLASHING HE208R RUBBERIZED WET PATCH ROOF LEAK REPAIR HE107 ASPHALT EMULSION SEALER AND DAMPROOFER HE555 ALUMINUM HE555FR ALUMINUM HE280DC WHITE ELASTOMERIC ASTM D 4586, Type I trowel-grade flashing cement made from heavybodied asphalt reinforced with organic fibers applied 1/8-inch thick at a rate of 1 gal/12.5 ft 2. Use with asphalt coated, SBS modified, metal and masonry ASTM D 4586, Type I and ASTM D 3409 trowel-grade rubber polymer modified mastic compound of asphalt, organic fibers and mineral fillers applied to wet or dry surfaces 1/8-inch thick at a rate of 1 gal/12.5 ft 2. Use with asphalt composition, SBS modified, metal and masonry ASTM D 4586, Type I/II and ASTM D 3409 trowel-grade compound for sealing roof leaks on wet surfaces applied 1/8-inch thick at a rate of 1 gal/12.5 ft 2. Use with asphalt, BUR, SBS modified, metal and masonry ASTM D 4586, Type I trowel-grade sealant made from refined asphalt for dry surfaces. Applied 1/8-inch thick at a rate of 1 gal/12.5 ft 2. ASTM D 4586, Type I Class I, trowel-grade rubberized flashing cement designed for use with SBS modified bituminous roofing and asphalt coated membranes. Applied at a rate of 1 gal/ 12.5 ft 2. ASTM D 4586, Type I Class II and ASTM D 3409, trowel-grade SBS modified bitumen used for repair of roof leaks on wet surfaces. Applied at a rate of 1 gal/ 12.5 ft 2. Use with asphalt, BUR, SBS modified, metal and masonry ASTM D 1227, Type II Class I, brush/spray-grade asphalt emulsion coating used for maintenance of roofing materials applied at a rate of 3-4 gal/ 100 ft 2. Use with composition ASTM D 2824, Type III, fibered aluminum roof coating used for maintenance of roofing materials. Applied at a rate of gal/ 100 ft 2. Use with asphalt, BUR, modified bituminous, and weathered galvanized and tin ASTM D 2824, Type III, applied at a rate of gal/ 100 ft 2. Use with asphalt, BUR, modified bituminous, metal, and primed masonry ASTM D 6083 water-based acrylic latex coating. Application rates are as follows: Smooth Surfaces: 2 to 2-1/2 gal/100 ft 2 applied in two coats Mineral Cap Sheet: 2 to 3 gal/ 100 ft 2 applied in two coats Use with concrete, galvanized steel, SBS modified, BUR, EPDM, and PVC. HEN13001 FL10889 Page 2 of 5

3 HE289 WHITE ROOFING SEALANT HE553 MBA GOLD MODIFIED BITUMEN ADHESIVE HE201 FIBERED BLACK ROOF COATING HE ASPHALT PRIMER PRO-GRADE ALL WEATHER FLASHING #27; PRO-GRADE ALL WEATHER FLASHING #225 PRO-GRADE SILVER MEDAL MB FLASHING #531 ELASTOMERIC PRO-GRADE 226 PLASTIC ROOF PRO-GRADE 812 FIBERED ALUMINUM PRO-GRADE 832 FIBERED ALUMINUM TAS 139, white, elastomeric patching compound used for repair of roof leaks prior to coating. Applied at a rate of 1 gal/ 12.5 ft 2. Use with SBS modified, metal, and masonry ASTM D 3019, Type III, fibrated rubberized adhesive for use with adhering modified bituminous and asphalt coated membranes. Applied at a rate of 1.5 gal/ 100 ft 2. ASTM D 4479, Type I, brush or spray-grade used for maintenance of roof materials. Applied at a rate of 1.5 gal/ 100 ft 2. Use with metal, SBS modified, or composition ASTM D 41 Type II, asphalt primer for use with smooth surface roofs, concrete, masonry, brick, and metal surfaces. Applied at a rate of 1 gal/200 ft 2. ASTM D 4586, Type I Class II and ASTM D 3409, trowel-grade flashing cement for sealing roof leaks on dry or wet surfaces applied at a rate of 1 gal/ 12.5 ft 2. ASTM D 4586, Type I Class I, trowel-grade plastic roof cement applied 1/8-inch thick at a rate of 1 gal/ 12.5 ft 2. Use with asphalt, metal and composition roof surfaces. ASTM D 2824, Type III, coating for use with smooth surface asphalt built-up and modified bitumen membranes applied at a rate of 1 gal/ 75 ft gal/ 100 ft 2. ASTM D 2824, Type I coating for use with smooth surface asphalt built-up and modified SBS and APP bitumen membranes. Application rates are as follows: Smooth Surfaces: gal/ 100 ft 2 Mineral Cap Sheet: gal/ 100 ft 2 Masonry and smooth surface SBS and APP roofs surfaced with hot asphalt must first be coated with fully-cured asphalt emulsion. PRO-GRADE 842 FIBERED ALUMINUM PRO-GRADE 331 COLD PROCESS ROOF ADHESIVE PRO-GRADE 441 FIBERED ROOF COATIING ASTM D 2824, Type III, coating for use with built-up asphalt, prepared roll roofing, smooth surface modified bitumen membranes, weathered galvanized iron or tin applied at a rate of gal/ 100 ft 2. ASTM D 3019, Type III, brush-grade, cold-applied, adhesive for use with asphalt coated or self-adhering modified bitumen products applied at a rate of 2 gal/ 100 ft 2. ASTM D 4479, Type I, heavy-bodied asphalt coating reinforced with fiber applied at a rate of 2 gal/ 100 ft 2. Use with asphalt, metal and composition roofs HEN13001 FL10889 Page 3 of 5

4 PRO-GRADE 535 SILVER MEDAL MBA MODIFIED BITUMEN ADHESIVE PRO-GRADE 162 FIBERED ASPHALT EMULSION BULL 100 PREMIUM ALUMINUM ROOF COATING BULL 900 SPECIAL FLASHING BULL 700 PLASTICE ROOF BULL 200 ASPHALT PRIMER SL1100- SUNNILAND PLASTIC SL1400 SUNNILAND PREMIUM MODIFIED SL1300 SUNNILAND ALL WEATHER FLASHING PR300 PREMIER PLASTIC ROOF PR350 PREMIER WET OR DRY PLASTIC ROOF PR400 PREMIER COLD PROCESS ADHESIVE ASTM D 3019, Type III, fibrated, rubberized adhesive for use with SBS modified bitumen and asphalt-coated membranes applied at a rate of 1.5 gal/ 100 ft 2. Not to be used with SBS membranes single ply with polyethylene backing or APP products. ASTM D 1227, Type II Class I, brush/spray-grade coating of an asphalt base with a clay emulsion that contains mineral fibers for use in damp proofing new or existing asphalt roofs, galvanized or ungalvanized metal, composition roofing or periodic maintenance recoating applied in two coats at a rate of 3-5 gal/ 100 ft 2 /coat. ASTM D 2824, Type III, coating used for smooth surface asphat builtup, modified bitumen membranes and metal applied at a rate of 1 gal/ 75 ft 2-1 gal/ 100 ft 2. compound for roof flashings applied to wet or dry surfaces 1/8-inch thick at a rate of 1 gal/ 12.5 ft 2. ASTM D 4586, Type I Class I, trowel-grade mastic compound applied 1/8-inch thick at a rate of 1 gal/ 12.5 ft 2. Not for use over coal tar. ASTM D 41 Type II, solution of asphalt base in a petroleum solvent applied at a rate of 0.5 gal/ 100 ft 2. ASTM D 4586, Type I Class I, trowel-grade mastic compound for vertical and horizontal applications applied 1/8-inch thick at a rate of 1 gal/ 12.5 ft 2. For use repairing leaks on metal roofs, shingles, composition roofing and asphalt. ASTM D 4586, Type I Class I, trowel-grade mastic compound applied to wet or dry surfaces 1/8-inch thick at a rate of 1 gal/ 12.5 ft 2. For use repairing leaks on metal roofs, shingles, concrete, masonry and brick. Not for use over coal tar. compound for wet or dry surfaces applied 1/8-inch thick at a rate of 1 gal/ 12.5 ft 2. For use repairing leaks on metal roofs, shingles, concrete, masonry and brick. Not for use over coal tar. ASTM D 4586, Type I Class I, trowel-grade mastic applied 1/8-inch thick at a rate of 1 gal/ 12.5 ft 2. For use with asphalt, metal and composition compound for wet or dry surfaces applied 1/8-inch thick at a rate of 1 gal/ 12.5 ft 2. For use repairing leaks in composition, mineral surface cap sheet, asphalt coated, SBS modified, metal, roofs, shingles, concrete, masonry and brick. ASTM D 3019, Type III, cold-applied asphalt roofing adhesive applied at a rate of 2 gal/ 100 ft 2. PR550 PREMIER ALUMINUM ROOF COAT ASTM D 2824, Type III, coating for use on smooth surface asphalt built-up, metal and modified bitumen membranes applied at a rate of gal/ 100 ft 2. HEN13001 FL10889 Page 4 of 5

5 ROOFER S CHOICE ASPHALT EMULSION ASTM D 1227, Type II Class I, brush/spray-grade coating for smooth surfaces applied in one coat or at right angles in two coats at a rate of 3 gal/ 100 ft 2 /coat. LIMITATIONS 1. Fire classification is not within the scope of this evaluation. 2. Structural integrity of the roofing substrate or assembly is not within scope of this evaluation. Refer to the appropriate product approval for installation of these components within an Approved roof assembly. 3. Installation of the evaluated products shall comply with this report and the manufacturer s published application instructions. 4. Applications are valid for new and existing roof systems. COMPLIANCE STATEMENT The products evaluated herein have demonstrated compliance with the 2010 Florida Building Code as evidenced in the referenced documents submitted by the named manufacturer. Zachary R. Priest, P.E. Florida Registration No Organization No. ANE9641 CERTIFICATION OF INDEPENDENCE does not have, nor will it acquire, a financial interest in any company manufacturing or distributing products under this evaluation. is not owned, operated, or controlled by any company manufacturing or distributing products under this evaluation. Zachary R. Priest, P.E. does not have, nor will acquire, a financial interest in any company manufacturing or distributing products under this evaluation. Zachary R. Priest, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the product. END OF REPORT HEN13001 FL10889 Page 5 of 5