24/24-W/48/48-W/88/168

Transcription

1 Istallatio Maual Premier Elite 24/24-W/48/48-W/88/168 & 640 Revisio 9 INS176

2 Cotets Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Cotets Cotets... 2 Trouble-Shootig Reset ad Service Messages Sstem Overview... 4 Sstem Architecture Programmig the Cotrol Pael Cotrol Pael... 4 Itroductio Remote Kepads... 5 Copig ad Pastig Zoe Expaders... 6 Log Off Egieer Output Expaders... 6 Resettig the Egieers Code (User 00) Commuicators Zoe Setup Other Devices... 6 Ricochet Devices MT Istallatio... 7 Zoe Tpes Istallatio Sequece... 7 Zoe Attributes Cotrol Pael... 7 Zoe Attributes Power Suppl Ratigs Attributes for Momet or Latch Kes Coectig AC Mais Attributes for Custom Zoes Coectig Batteries Zoe Areas 24/48/88/ Coectig Devices to the Network Zoe Areas Remote Kepads Zoe Text XP-W & 32XP-W V2.xx> Zoe Chime Sstem Desig Cosideratios Remote Test Eable Ricochet MT2 Expader Addressig Zoe Wirig XE Zoe Expader (24 Ol) Zoe Groups XP Zoe Expader DD Star ad Dais Jumper Optio Area Programmig iprox Module Timers iXD Zoe Expader Armig Modes OP16 Output Expader Area Arm Suites 24/48/88/ RM8 Rela Module Area Arm Suites Zoe ad Output Numberig 24/48/88/ Area Suite Text Zoe ad Output Numberig Suite Arm Modes Zoe Coectios Area Optios 24/48/88/ IXD Zoe Expader Area Optios Auxiliar/Fault Coectios Time Arm Area Speaker Coectios Area Text Exteral Souder Coectios Global Optios Pael Outputs Sstem Timers Digicom Outputs Sstem Cofig Wire Smoke Detector Sstem Optios Expader Auxiliar Iput Moitor Hardware Plug-o Commuicators Cotrol Timers Com GSM Sstem Text SIM Card Tpes Part Arm Text Premier Elite ComGSM Laout Holida Dates Aerial Sitig Speaker Toes Istallatio PC Output Text Pael Cofiguratio Custom O/P Text Usig the SMS Cotrol Commads What will be set i the Text Message Kepad Setup AV Module Kepad Areas ComIP Module Kepad Zoe Mappig Commissioig Kepad Optios USB-Com Kepad Speaker Volume PC-Com Kepad Souder Optios PRINT-Com Expader Setup Coectig a Computer Expader Areas Coectig a Priter Expader Locatio Text Commissioig ad Troubleshootig Expader Auxiliar Iput Commissioig INS176-9

3 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Cotets Expader Speaker Volume Chage Eg. Code Expader Souder Optios Adjust Volumes Sstem Outputs Default NVM Data Locatio Text Available Outputs Prit Log Data Programmig Outputs Soak Test Areas 24/48/88/ Output Group - Not Used Soak Test Areas Output Group - Sstem View id Data Output Group - Area Cofigure Radio Output Group - Zoe Ricochet Diagostics (MT2 Ol) Output Group - User Code Etered Output Group - Cotrol Timer Programmig Part Arms Output Group - PC Cotrol Alter Part Arms Output Group - Door Cotrol Specificatios Cotrol Paels Output Attributes Remote Kepads X-10 Outputs Zoe Expaders Custom Outputs Output Expaders Zoe Group Outputs Stadards UDL/Digi Optios Warrat Reset Digi Notes: Start Test Call Notes MSN/Pre-Dial No Program Digi Digi Optios Area Accouts 24/48/88/ Area Accouts UDL Optios Setup Modules Com Port Setup DualCom Iside (48 Ol) EMIZON 21 TCD WebWaOe Chiro IRIS Zoe Alarm Reportig Codes Setup Users Default User Codes Programmig New Users User Tpes User Fuctios ad Optios User Optios User Optios User Cofig User Time Lock User Name Text Door Cotrol Addig Tags Deletig Users Addig SmartKe Egieer Utilities View Evet Log Do Bell Test Do Walk Test 24/48/88/ Do Walk Test View Zoe Status Do Sstem Tests Cofirm Devices View RKP Status View Exp. Status Set Sstem Time Set Sstem Date INS

4 Sstem Overview Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 1. Sstem Overview Sstem Architecture 8 to 24 zoes ( Premier 24) 8 to 4 8 Zoe s ( Premier 48) 8 to 8 8 Zoe s ( Premier 88) 8 to 16 8 Zoe s ( Premier 168) 0 to 64 0 Zoe s ( Premier 640) 8 Zoe Iputs 2 Zoe I pu ts 4 ke pads ( Premier 24) 4 K e pa ds ( P remi er 48 ) 8 K e pa ds ( P remi er 88 ) 16 K e pa ds ( P remi er 16 8) 64 K e pa ds ( P remi er 64 0) 1Programmable 100mA Output 2 Zoe I pu ts 1Programmable 100mA Output 1 Output Module ( Premier 24) 2 O utput Modules ( P remier 48) 4 O utput Modules ( P remier 88) 8 Output Modules ( Premier 168) 32 O utput Modules ( P remier 640) 16 Programmable 100mA Outputs 2 E xpade rs ( Premier 24) 4 E xpade rs ( Premier 48) 8 E xpade rs ( Premier 88) 16 Expaders ( Premier 168) 64 Expaders ( P remier 640) 8 Zoe Iputs 8 Programmable 100mA Outputs Premier 24/48/88/168/640* S pea ker Output 8 Programmable 100mA Outputs Speaker Output Auxiliar Iput 5 Programmable Outpu ts (4 x 500mA & 1 R ela) ( Premie r 8 8,168 & 640 o l) 4 Wire Data Netwo rk 1 Add itio al 4 Wire Data Ne two rk Premi er LC D/LC DP Wire a s Network 1 Premier LC DL /LC DLP Premier O P16 Premier 8XP Bell/S trobe Outputs Bell Ta mper Iput Auxiliar Ta mper Iput P lug o D igimode m (Com30 0, Com24 00) GSM Module We bwao e, E mizo or C hiro Iris P C ad Modem for R emote Upload/Dowload Modem PC ad PC -Com for Local Uploa d/dowload PC-Com Alarm Receivig Cetre * No Oboard Zoes Cotrol Pael Premier Elite 24 8 full programmable Double Pole or Ed Of Lie zoes Expadable to 24 zoes via kepads ad zoe expaders 1 x 4-wire data etwork (stadard 7/0.2 alarm cable) Up to 4 kepads ad 2 zoe expaders Up to 1 output module 2 idepedet areas each with 3 part arms 2 area arm suites 25 programmable User codes 500 Evet Log (time & date stamped) 1 programmable pael outputs (1 x 100mA ) 1.5 Amp power suppl (plastic Case) Premier Elite 48 8 full programmable Double Pole or Ed Of Lie zoes Expadable to 48 zoes via kepads ad zoe expaders 1 x 4-wire data etwork (stadard 7/0.2 alarm cable) Up to 4 kepads ad 4 zoe expaders Up to 2 output modules 4 idepedet areas each with 3 part arms 4 area arm suites 50 programmable User codes 500 Evet Log (time & date stamped) 2 programmable pael outputs (2 x 1A ) 2.5 Amp power suppl Premier Elite 24-W & 48-W 4 Oboard Zoes 8 wireless device Ricochet eabled receiver oboard (24-W) 32 wireless device Ricochet eabled receiver oboard (48-W) Expadable to 24/48 zoes via kepads ad zoe expaders 1 x 4-wire data etwork (stadard 7/0.2 alarm cable) Up to 4 kepads ad 2/3 zoe expaders Up to 2 output modules 2 or 4 idepedet areas each with 3 part arms 2 or 4 area arm suites 25 or 50 programmable User codes 500 Evet Log (time & date stamped) 1 or 2 programmable pael outputs (2 x 500mA ) 1.5 Amp power suppl Premier Elite 88 8 full programmable Double Pole or Ed Of Lie zoes Expadable to 88 zoes via kepads ad zoe expaders 1 x 4-wire data etwork (stadard 7/0.2 alarm cable) Up to 8 kepads ad 8 zoe expaders Up to 4 output modules 8 idepedet areas each with 3 part arms 8 area arm suites 100 programmable User codes 1000 Evet Log (time & date stamped) 5 programmable pael outputs (4 x 1A & 3A rela) 4 INS176-9

5 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 2.5 Amp power suppl Premier Elite full programmable Double Pole or Ed Of Lie zoes Expadable to 168 zoes via kepads ad zoe expaders 2 x 4-wire data etwork (stadard 7/0.2 alarm cable) Up to 16 kepads ad 16 zoe expaders (8 per etwork) Up to 8 output modules (4 per etwork) 16 idepedet areas each with 3 part arms 16 area arm suites 200 programmable User codes 2000 Evet Log (time & date stamped) 5 programmable pael outputs (4 x 1A & 3A rela) 2.5 Amp power suppl Premier Elite full programmable Double Pole or Ed Of Lie zoes Expadable to 640 zoes via kepads ad zoe expaders 8 x 4-wire data etwork (stadard 7/0.2 alarm cable) Up to 64 kepads ad 64 zoe expaders (8 per etwork) Up to 64 output modules (8 per etwork) 64 idepedet areas each with 3 part arms 64 area arm suites 500 programmable User codes 5000 Evet Log (time & date stamped) 5 programmable pael outputs (4 x 1A & 3A rela) 2.5 Amp power suppl Premier Elite 24, 24-W, 48, 48-W, 88, 168 & Evet Alarm Log 500 Evet Madator Log 8 programmable digicom outputs (100mA each) 32 character zoe text Facilit for Plug-o Digimodem (Com300/2400/) Facilit for Plug-o IP Module (ComIP/Chiro/WebWaOe/Emizo) Facilit for a plug-o RedCARE/RM8 Rela Module (Not Premier 24) PC-Com/priter port Remote Kepads LCD 32 character text displa 2 full programmable DP or EOL zoes 1 full programmable output (100mA -ve applied) Full adjustable back-lightig, ormall bright, dim or off, chagig to bright durig etr or followig a ke press Built i piezo souder Programmable Ifo. LED LCDL ALL the features of the LCD plus: Larger 32 character text displa Speaker output LCDP LCD with a built i Proximit Tag Reader LCDLP LCDL with a built i Proximit Tag Reader FMK/SMK LCDLP Metal Flush or Surface Mout Various fiishes available RKP8/16Plus LED Armig kepad 2 full programmable EOL zoes CANNOT be used for Programmig Ico Guide Eglish UK Kepad Omit PR X F PR X F Icoic Kepad S ervice Sstem Overview Po wer Ifo. Read O R C PA e B C s A Eglish Kepad e B C s A N P b R N P b R N INS

6 Sstem Overview Kes ICONS UK Eglish Eglish = = = = = = = = = = = = = = = = = = LED's Zoe Expaders 8XP = Power = Read = Armed/Ifo OK = Read = Omit = Service 8 full programmable DP or EOL zoes 8 full programmable outputs (100mA -ve applied each) Speaker output Programmable auxiliar iput Remotel wired 60iXD 2 loops x 30 full programmable id zoes id biscuit techolog Plug-o id is a registered trade mark of Chloride Safet Sstem Limited. Output Expaders OP16 16 full programmable outputs (100mA each) 1 fault output (100mA -ve applied) Ca be coected to mimic paels to give zoe idicatio Ca be coected to relas ad souders RM8 Rela Module Plug-o rela card (RedCARE footprit) 8 separate iputs for stadaloe operatio 8 x 3Amp rela outputs (/o, /c, com) Output ON LED idicatio Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual For use with a aalogue telephoe lie (REN = 1) Com2400 Multi-protocol commuicator supportig Fast Format, Cotact ID, SIA Level II ad EasCom Pager ad SMS Messagig protocols 2400-baud modem for remote uploadig ad dowloadig usig the Witex UDL software ad a PC Seds SMS text messages to mobile phoes For use with a aalogue telephoe lie (REN = 1) ComIP Multi-protocol commuicator supportig Fast Format, Cotact ID ad SIA Level II protocols via TCP/IP High speed modem for remote uploadig ad dowloadig usig the Witex UDL software ad a PC For use with ADSL/DSL/Broadbad/WAN/LAN etc. ComGSM Provides a GSM telephoe path for Com300 & Com2400 Digital Commuicators Seds SMS text messages to mobile phoes Arm, Disarm, Reset the alarm, tur outputs o ad off, omit zoes ad sed messages to the cotrol pael usig SMS text messages 9600-baud modem for remote uploadig ad dowloadig usig the Witex UDL software ad a PC Other Devices PC-Com For coectig a PC to the cotrol pael via a RS232 Serial port allowig local uploadig ad dowloadig usig Witex UDL software USB-Com For coectig a PC to the cotrol pael via a USB 1.0 or 2.0 port allowig local uploadig ad dowloadig usig Witex UDL software PRINT-Com For coectig a serial priter to the cotrol pael Memor Module (ot 640) Fits oto the expasio port to provide a 10,000 evet log. Batter Splitter Allows two backup batteries to be coected to a sigle set of batter termials, ad will provide appropriate moitorig ad chargig for each. Exteral Souders Texecom suppl a rage of exteral souders Commuicators Com300 Multi-protocol commuicator supportig Fast Format, Cotact ID, SIA Level II ad EasCom Pager protocols 300-baud modem for remote uploadig ad dowloadig usig the Witex UDL software ad a PC 6 INS176-9

7 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Istallatio 3. Istallatio Istallatio Sequece Before attemptig to istall the alarm sstem, read this sectio. Oce ou have a overall uderstadig of the istallatio sequece, carefull work through each step. 1: Desig the Laout Make a rough sketch of the premises to get a idea of where the alarm detectio devices, kepads, zoe expaders etc. are to be located. 2: Moutig the Pael The cotrol pael should be mouted i a dr area close to a uswitched AC power source ad the icomig telephoe lie (if usig a commuicator). You must complete all wirig before coectig the batter or applig AC mais to the cotrol pael. 3: Istall the Kepads ad Zoe Expaders Mout ad coect the kepads, zoe expaders ad output modules to the cotrol pael (see page 20 for wirig details). 4: Istall the Alarm Detectio Devices Istall the detectio devices, PIR s, Cotacts, PA Buttos etc. ad coect them to the cotrol pael (see page 31 for wirig details). 5: Istall the Exteral Souder Istall the exteral souder ad coect to the cotrol pael (see page 33 for wirig details). 6: Other Wirig Complete all other wirig icludig speakers, telephoe lie ad output coectios etc. (see pages for details). 7: Applig Power to the Cotrol Pael Oce steps 1 to 6 are completed, power ca be applied to the cotrol pael. Whe applig power for the first time, the factor default settigs must be loaded (see page 42 for details). Power should alwas be coected i the followig order: Coect the red batter lead to the positive termial of the batter ad the coect the black batter lead to the egative termial The pael will ol become live whe the AC Mais is coected or the Batter Kick-start butto is pressed. Cotrol Pael Moutig Mout the cotrol pael o a flat, plumb wall usig at least three screws of appropriate size. It is essetial to esure that oe of the fixig slots or cable etries are accessible after fixig. Mais cablig must be secured (e.g. with a cable tie) to oe of the achor poits provided. Wirig the Cotrol Pael WARNING: ELECTRICITY CAN KILL BEFORE coectig the cotrol pael ALWAYS discoect the suppl at the cosumer uit. If i ANY doubt cosult a qualified electricia. IMPORTANT SAFETY INFORMATION. HAZARDOUS VOLTAGES INSIDE, NO USER SERVICEABLE PARTS, NO USER ACCESS. ONLY coect the mais suppl to the mais termial block, NEVER coect the mais suppl directl to the PCB. ALWAYS refer to Natioal Wirig Regulatios whe coductig istallatio. A appropriate ad readil accessible discoectio device (e.g. a uswitched fused spur) MUST be provided as part of the istallatio. The discoectio device must NOT be fitted i a flexible cord. Where idetificatio of the eutral i the mais suppl is NOT possible a two-pole discoectio device MUST be used. Use mais cable of adequate carrig capacit for the rated curret (i.e. at least 0.75mm 2 ). Coect the AC mais For a complete list of factor default settigs, see the Quick Referece Guide supplied with our pael. 8: Programmig the Cotrol Pael Please refer to sectio 5 for istructio o programmig the cotrol pael. 9: Testig the Sstem Test the sstem thoroughl to esure that all features ad fuctios operate as required (see page 112 for details). INS

8 T R T R Istallatio Premier Elite 24 Cotrol Pael Laout Polmer Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual E x pas io L/M R /R C om 1 Audio Cotrol Pael C ircuit B oard F6 F2! USE WITH T E XE C O M P S U O NLY K ic k S tar t B att DC B ell 0.75A 0.3A B att C h ar ge Network Aux 12V F3 L oad D e faults Com1 F las h P ort F9 B AR CODE Digi Mode m Com2 Plug-o Digimodem (Com300, Com2400 ) F4 F1 + B a tt - DC + DC - 2 Wire S m oke B ell + 12V E able E a b le Egieer Remote Tx Rx N et w o rk F8 + T R Aux Tamp Z1 Z2 Z3 Z6 - Z4 Z5 Z7 + - Aux/F aul t S trb 0V B ell+ 1 2V P g 1 S pk - 12V Z8 R1 T1 Mais Termial Block & Cable Etr C able E tries 1.5 Amp Mais PSU No user serviceable part s iside. Do ot ope! Rated Iput: 100V 50/60Hz; 1A Rated Output Curret@ 55 C: 1.5A MAX Ra ted Output Volt age: 13.7Vdc +/- 2% Mais Termial Block Fuse: 250Vac; 3A-3. 15A Slow/Me dium Blow LAB A POWER SUPPLY DANGER HIGH VOLTAGE S pace for 1 x 7Ah B atter Premier Elite 24-W & 48-W Cotrol Pael Laout Ta mpe r D is abl e J p1 B AR Di gi Modem F2 Cotrol Pael C ircuit B oard + Ba tt- L/M R /R DC + DC Di gic om O /P s F1 F8 Ki ck Start F3 Egieer R EM Tx R x 0.75A 0.3A L E D1 J p2 B a tt C h arg e C om 1 J p3 C om 2 E x pas io J p9 N et wo r k Aux 1 2V Bell 12V F4 F5 F6 L oad De fa ult s F7 E a ble S mok e R i co c h e t M o i to r J p4 J p6 Tx R x F it f or Comm is sio Mode ON J p OPTIONS! US E W ITH TEXECOM PSU O NLY R1 T1 Plug-o Digimodem (Com300, Com2400 ) + - T R AUX 12 V AUX 0V S tr b 0V Tam p B e ll + 1 2v AUX F au lt S pk+ S pk- O P 1- O P 2- Z1 Z2 Z3 Z4 Mais Termial Block & Cable Etr C able E tries 1.5 Amp Mais PSU No user ser viceable parts iside. Do ot ope! Rate d Iput: 1 00 V 24 50/ 60Hz; 1A Rated Output 55 C: 1.5A M AX R ate d O ut pu t V o ltag e: Vdc +/ - 2% Ma is Ter mi al B lo ck Fu se: 250Vac; 3A-3.15A Slow/M edium Blow LAB A POWER SUPPLY DANGER HIGHVOLTAGE S pace for 1 x 7Ah B atter 8 INS176-9

9 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Istallatio Cotrol Pael Laout Metal All Models (168 show) Ta mper Mais Termial S witch Block & Cable Etr 2.5 Amp Mais PSU 2. 3A / 2.5A POWER SUPPLY No user serviceable part s iside. Do ot ope! T R BT C able E tr R ate d Iput : 22 0V 50/60Hz; 1A Rated Output 40 C: 2.5AMAX Aud io T1 DANGER HIGHVOLTAGE R ate d Iput : 10 0V 50/60Hz;1A Rated Output 40 C: 2.3AMAX Rated Output Voltage: 13.7Vdc +/- 2% Ma is Termial Block Fuse: 250Vac; 3A- 3.15ASlow/ MediumBlow Com 1 R1 Plug-o Digimodem (Com300, Com2400)! P rog ra mmig P ort L/M R /R + - B AT T F6 F2 F7 E able S m ok e N /O C OM N /C OP5 O P 4+ O P 3+ DC+ O P 2- DC- O P 1-1 F9 S pk - Cotrol Pael C ircuit B oard DIGIC OM OUTPUTS F3 C om 2 C om 1 F5 F1 BAR CODE F8 S pk + A u x/ F ault + 12 v B ell - Ta mp 0v E xpas io V S trb - Tx 1 R x1 Tx 2 R x2 + - T R + - T R NE TWOR K 1 NE TWOR K 2 + Au x - 12v A T Zo e 1 A T Zo e 2 A T Zo e 3 A T Zo e 4 A T Zo e 5 A T Zo e 6 A T Zo e 7 A T Zo e 8 F4 Be ll/s trb - 1A mp C able E tries S pace for 1 x 7Ah Batter 2 x 7Ah B atteries or 1 x 17Ah B atter C able E tries INS

10 Istallatio Premier Elite 24 PCB Laout Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Expasio Tamper Dis able Tamper L /M R /R! USE WITH TEXE CO M PS U ON LY Kick Start 0.75A 0.3A Batt C harge Load Defaults C om1 Flash Port F9 BAR CODE Digi Modem F6 F2 B att DC B ell N etwork F3 Aux 12V C om2 F4 F1 + B att - DC+ DC- 2 Wire S moke E able B ell + 12V E able E gie er R emote Tx Ne twork Rx F8 Tamp + - Aux S trb 0V Bell+ 12V T R Op1 S pk Aux/Fa ult Z1 Z2 Z3 Z4 Z5 Z6 Z7 12V Z8 1: Texecom PSU Coectio Coected to the Texecom Switch Mode Power Suppl. DO NOT CONNECT THE MAINS SUPPLY TO ANY TERMINALS ON THE PCB. 2: Batter Kick-start Butto Whe powerig up the pael without AC Mais preset, this butto must be pressed i order to coect the batter. If AC Mais is preset this butto does ot eed to be pressed. 3: Earth Coectio Coects the PCB to earth 4: Batter Coectios A 12V rechargeable batter must be coected to these termials i order to provide cotiuous sstem operatio i the evet of a AC Mais failure (see page 19 for details). 5: Digicom Power These termials provide power; ad are ormall used for coectig a stad-aloe commuicator to the cotrol pael (see page 34 for details). 6: Exteral Souder Coectios These termials are used for coectig to a exteral souder uit (see page 33 for details). 7: Network Data Coectios & LED s Networks provide coectio for the kepads ad zoe expaders The + ad termials provide power whilst the T trasmits data ad R receives data (see page 20 for details). The red LED idicates that data is flowig out of the cotrol pael ad ormall flashes ver quickl. The gree LED idicates that data is flowig ito the cotrol pael ad ormall flashes slowl, the gree LED flashes faster as more devices are coected (see page 20 for details). 8: Pael Output 1 OP1 is a low curret (500mA -ve applied) output (see page 34 for wirig details). The output is also full programmable (see page 77 for programmig details). 9: SPK- Loudspeaker Coectio These termials ca be used for coectig up to oe 16Ω or two 8Ω loudspeakers (see page 33 for wirig details). 10: Auxiliar 12V Power These termials are for coectig devices that require 12V power (protected b a 1A fuse). 11: Auxiliar/ Fault Coectios These termials ca be used for moitorig the tamper loop of a auxiliar device (see page 33 for details). 12: Programmable Zoes 1-8 These termials provide the coectios for the zoes (see page 31 for wirig details). Each zoe is full programmable (see page 48 for details). 13: Expader Port The expasio port is used for pluggig o a local zoe expader (see page 23 for details). 14: Com Port 2 Com Port 2 is a serial commuicatios port ad ca be used for coectig a PC ruig Witex or a supported serial device to the cotrol pael (see page 94 for details). 15: Plug-o Commuicator Coectios This socket provides coectio for the plug-o commuicator (see page 36 for details). 16: Digicom Outputs Outputs 1 to 8 are low curret (100mA -ve applied) ad would ormall be used whe coectig a stad-aloe commuicator to the cotrol pael (see page 34 for details). Each output is full programmable (see page 77 for details). A remote reset iput ad a lie fault iput are also provided. 17: Flash Upgrade Port For use with the Flasher iterface to update pael firmware. 18: Box Tamper Coectio The micro switch provides tamper protectio for the mai cotrol pael i case of uauthorised access. 19: Com Port 1 Com Port 1 is a serial commuicatios port ad ca be used for coectig a PC ruig Witex or a supported serial device to the cotrol pael (see page 94 for details). 20: Tamper Disable Lik This ca be used to disable the box tamper whe workig with the box lid removed. 10 INS176-9

11 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Istallatio 21: Load Defaults Butto Press ad hold this butto whilst applig power to the cotrol pael to load the factor default settigs. Press ad hold this butto for 7 secods with power alread o the pael to restore just the Egieer code to the factor settig of. Loadig the factor defaults ca take up to 30 secods to complete. Loadig defaults will ol be possible if the NVM has ot bee locked (see page 64 for details). For a complete list of factor defaults, see the Quick Referece Guide sectio of this maual. 22: Expasio The Expasio Port ca be used for coectig a 60XiD Zoe Expader (see page 32 for details) or a AV Module (see page 40 for details), X-10 Module or a Memor Module. 23: Heartbeat LED/Power Light Flashes steadil to idicate that the cotrol pael is fuctioig correctl. If the light is ON or OFF all the time, the there could be a problem (see page 42 for details). 24: Batter Charge Curret Selector Whe usig a 7Ah stadb batter the charge curret selector should be set to 300mA. If a 17Ah batter is coected (metal cabiet ol) the selector should be set to the 750mA positio. 25: Egieers Kepad A portable Egieers kepad ca be plugged o here to allow easier access for programmig ad testig. Whe usig a kepad as a Egieers kepad, the address must be set to 10 (see page 22 for details). The kepad zoes ad lid tamper are ot moitored. F1 F6: Protectio Fuses (electroic PTC) The followig fuses are provided: F1 (900mA) Auxiliar 12V Power fuse (electroic PTC) F2 (900mA) Digicom Power (electroic PTC) F3 (900mA) Network 1 fuse (electroic PTC) F4 (900mA) Bell/Strobe fuse (electroic PTC) F6 (1.6 Amp) Batter fuse (electroic PTC) INS

12 Istallatio Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Premier Elite 24-W & 48-W PCB Laout F2 Ta m per D is a ble J p1 B AR C ODE D igi Modem B at t- L/M R /R DC + DC Digicom O/P s F1 F8 K i ck S ta r t F3 Egi eer REM Tx Rx 0.7 5A 0. 3A J p2 LED1 B a tt Ch a rge C om 1 J p3 C om 2 E x pas io J p9 N et w or k Aux 12V Bell 12V F4 F5 F6 Load Defaults F7 E a ble S m oke J p4 R icochet Moitor Wireless Eg Kpd Tx J p6 Rx Fit for C omm is si o M ode ON J p OPTIONS! US E W IT H TEXECOM PSU O NLY T R AUX 12V AUX 0V S trb 0V Tam p Be ll + 1 2v AU X F ault Spk+ Spk- OP1- OP2- Z1 Z2 Z3 Z : Batter Coectios A 12V rechargeable batter must be coected to these termials i order to provide cotiuous sstem operatio i the evet of a AC Mais failure. (protected b 1.6 Amp PTC Fuse) 2: Digicom Power & Iputs These termials provide u-fused power; remote reset ad lie fault iputs ad are ormall used for coectig a stad-aloe commuicator to the cotrol pael. 3: Digicom Outputs Outputs 1 to 8 are low curret (100mA -ve applied) ad would ormall be used whe coectig a stad-aloe commuicator to the cotrol pael. Each output is full programmable. 4: Egieers Kepad A portable Egieers kepad ca be plugged o here to allow easier access for programmig ad testig. Whe usig a kepad as a Egieers kepad, the address must be set to 10. The kepad zoes ad lid tamper are ot moitored. 5: Network Data Coectios Network 1 provides coectio for the kepads ad zoe expaders. The + ad termials provide power whilst the T trasmits data ad R receives data. 6: Network Data Idicators The red LED idicates that data is flowig out of the cotrol pael ad ormall flashes ver quickl. The gree LED idicates that data is flowig ito the cotrol pael ad ormall flashes slowl, the gree LED flashes faster as more devices are coected. 7: Commuicatio Ports Com Port 1 is a serial commuicatios port ad ca be used for coectig a PC ruig Witex or a supported serial device to the cotrol pael. Com Port 2 is a serial commuicatios port ad ca be used for coectig a PC ruig Witex or a supported serial device to the cotrol pael. 8: Auxiliar 12V Power These termials are for coectig devices that require 12V power (protected b a 0.9A PTC fuse). 9: Expasio The Expasio Port ca be used for coectig a 60XiD Zoe Expader (see page 32 for details) or a AV Module (see page 40 for details), X-10 Module or a Memor Module. 10: Exteral Souder Coectios These termials are used for coectig to a exteral souder uit. 11: Load Defaults Butto Press ad hold this butto whilst applig power to the cotrol pael to load the factor default settigs. Press ad hold this butto for 7 secods with power alread o the pael to restore just the Egieer code to the factor settig of. 12 INS176-9 Loadig the factor defaults ca take up to 30 secods to complete. Loadig defaults will ol be possible if the NVM has ot bee locked. For a complete list of factor defaults, see the Quick Referece Guide supplied o the eclosed CD. 12: Auxiliar/Fault Coectios These termials ca be used for moitorig the tamper loop of a auxiliar device (see page 33 for details). 13: Loudspeaker Coectios These termials ca be used for coectig up to oe 8Ω or two 16Ω loudspeakers. 14: Pael Outputs Outputs 1 & 2 are 500mA -ve. These outputs are all full programmable. (24-W ol output 1) 15: Zoe Coectios 4 Full programmable zoe iputs 16: Ricochet Network LED s Gree LED = Data received b the expader from the pael Red LED = Data trasmitted b the expader to the pael. (The flash rate depeds o the mode ad RF activit) 17: Eable 2 wire smoke Pael Output 1 ca be used for coectig up to 10, 12V 2-Wire smoke detectors. 18: Optios Switch Use to select the receiver fuctioalit. Switch 1 OFF =ot used o 48-W. Switch 2 OFF = 24-W & 48-W RICOCHET Mode ON = Not Used Switch 3 ON = Impaq Cotact-W Wired Iput 2 will report as Tamper (default) OFF = iput 2 will report as a Alarm. Switch 4 OFF Walk test

13 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Istallatio 19: RICOCHET Eg kepad coectio A egieer s kepad (LCD kepad ad iterface lead) ca be temporaril plugged oto this coector to allow sstem programmig ad testig. Set the kepad address switches to all ON. 20: RICOCHET Firmware Flash Port Coectios for flasher iterface to update RICOCHET receiver firmware. 21: Commissio Mode Jumper Fit whe learig ad placig devices, remove oce complete. 22: Atea RF atea 23: RF LED s Left = RED Trasmit, Middle = GREEN Receive, Right = RED Wireless Network Tick. 24: Plug-o Commuicator Coectios This socket provides coectio for COM300/COM2400 plug-o commuicators via the lead provided. 25: Ricochet Comm. Port Coectio Serial commuicatios port for coectig to a PC via PC Com/USB Com or Com IP for use with RICOCHET Moitor Software. 26: Cover Tamper Provides tamper protectio for the cotrol pael. 27: Heartbeat LED/Power Light Flashes steadil to idicate that the cotrol pael is fuctioig correctl. If the light is ON or OFF all the time, the there could be a problem. 28: Cover Tamper Disable Disables the lid tamper 29: Flash Programmig Port For upgradig the pael firmware. 30: Batter Charge Selectio Select.03A or 0.75A batter chargig curret 31: Curret Readig Pads To calculate the curret draw of the cotrol pael, measure the voltage across the two pads ad multipl b 10 i.e. Readig = 34mV (x10) = 340mV = 340mA. 32: Batter Kick-start Butto Whe powerig up the pael without AC Mais preset, this butto must be pressed i order to coect the batter. If AC Mais is preset this butto does ot eed to be pressed. 33: Power Suppl Coectio Ol for use with the Texecom PSU. DO NOT CONNECT ANY OTHER MAINS SUPPLY TO THESE TERMINALS PTC Protectio Fuses The followig fuses are provided: F6 PTC (0.9A) Auxiliar 12V Power fuse F4 PTC (0.9 A) Network 1 fuse F5 PTC (0.9 A) Bell/Strobe fuse INS

14 Istallatio Premier Elite 48/88/168 PCB Laout Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Box Tamp + - B AT T L /M R/R! US E W IT H TEXECOM PSU O NLY F6 F2 F7 Programmig Po rt E able S moke JP10 N/ O C O M N /C O P5 O P4+ O P3+ DC+ O P2- DC- O P1-1 F9 S pk - E g K e pa d DIGIC OM OUTP UTS F3 Network 1 1Am p C om 1 C om 2 F5 Network 2 1Am p Tx1 R x1 Tx2 R x2 + - T R + - T R NET WOR K 1 NET WOR K 2 F1 + Aux 12v 1Am p - Aux 12v A T Zoe 1 A T Zoe 2 E xp as io JP7 A T Zoe 3 He ar tbe at A T Zoe m V = 1 Am p V BAR CODE A T Zoe 5 A T Zoe 6 A T Zoe 7 F8 A T Zoe 8 F4 S pk+ Aux/ Fault + 12v Bell - Tamp 0v S trb - Be ll/s trb - 1Amp 1: Texecom PSU Coectio Coected to the Texecom Switch Mode Power Suppl. DO NOT CONNECT THE MAINS SUPPLY TO THE AC INPUT TERMINALS ON THE PCB. 2: Batter Coectios A 12V rechargeable batter must be coected to these termials i order to provide cotiuous sstem operatio i the evet of a AC Mais failure (see page 19 for details). 3: Digicom Power & Iputs These termials provide ufused power; remote reset ad lie fault iputs ad are ormall used for coectig a stad-aloe commuicator to the cotrol pael (see page 34 for details). 4: Digicom Outputs Outputs 1 to 8 are low curret (100mA -ve applied) ad would ormall be used whe coectig a stad-aloe commuicator to the cotrol pael (see page 34 for details). Each output is full programmable (see page 77 for details). 5: Egieers Kepad A portable Egieers kepad ca be plugged o here to allow easier access for programmig ad testig. Whe usig a kepad as a Egieers kepad, the address must be set to 10 (see page 22 for details). The kepad zoes ad lid tamper are ot moitored. 6: Network Data Coectios Networks provide coectio for the kepads ad zoe expaders. The + ad termials provide power whilst the T trasmits data ad R receives data (see page 20 for details). 7: Auxiliar 12V Power These termials are for coectig devices that require 12V power (protected b a 1A fuse). 8: Programmable Zoes 1-8 These termials provide the coectios for the zoes (see page 31 for wirig details). Each zoe is full programmable (see page 48 for details). 9: Exteral Souder Coectios These termials are used for coectig to a exteral souder uit (see page 33 for details). 10: Auxiliar/Fault Coectios These termials ca be used for moitorig the tamper loop of a auxiliar device (see page 33 for details). 11: Loudspeaker Coectios These termials ca be used for coectig up to oe 16Ω or two 8Ω loudspeakers (see page 33 for details). 12: Pael Outputs Outputs 1 & 2 are 500mA -ve applied, outputs 3 & 4 are 500mA +ve applied ad output 5 is a clea cotact rela (see page 34 for wirig details). These outputs are all full programmable (see page 76 for details). Pael outputs 3, 4 ad 5 are ol available o the 88 ad : Plug-o Commuicator Coectios This socket provides coectio for the plug-o commuicator (see page 36 for details). 14: Box Tamper Coectio The box tamper micro switch is coected here. The micro switch provides tamper protectio for the mai cotrol pael i case of uauthorised access. To disable the box tamper, remove the micro switch lead ad fit a jumper lik across the two pis. 15: Plug-o RedCARE/Dualcom Coectios These pis provide coectios for a plug-o RedCARE, Dualcom, Digicom or RM8 Rela module. Each output is full programmable (see page 77 for details). Whe a device is plugged o to these pis, ot all outputs ma be available, please refer to the relevat documetatio for details. 16: Flash Upgrade Port For use with the Flasher iterface to update pael firmware. 17: Batter Kick-start Butto Whe powerig up the pael without AC Mais preset, this butto must be pressed i order to coect the batter. If AC Mais is preset this butto does ot eed to be pressed. 14 INS176-9

15 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Istallatio 18: Commuicatio Ports Com Port 1 is a serial commuicatios port ad ca be used for coectig a PC ruig Witex or a supported serial device to the cotrol pael (see page 94 for details). Com Port 2 is a serial commuicatios port ad ca be used for coectig a PC ruig Witex or a supported serial device to the cotrol pael (see page 94 for details). 19: Network Data Idicators The red LED idicates that data is flowig out of the cotrol pael ad ormall flashes ver quickl. The gree LED idicates that data is flowig ito the cotrol pael ad ormall flashes slowl, the gree LED flashes faster as more devices are coected (see page 20 for details). For a complete list of factor defaults, see the Quick Referece Guide supplied with our pael. 20: Load Defaults Butto Press ad hold this butto whilst applig power to the cotrol pael to load the factor default settigs. Press ad hold this butto for 7 secods with power alread o the pael to restore just the Egieer code to the factor settig of. Loadig the factor defaults ca take up to 30 secods to complete. Loadig defaults will ol be possible if the NVM has ot bee locked (see page 64 for details). 21: Expasio The Expasio Port ca be used for coectig a 60XiD Zoe Expader (see page 32 for details) or a AV Module (see page 40 for details), X-10 Module or a Memor Module. 22: Heartbeat LED/Power Light Flashes steadil to idicate that the cotrol pael is fuctioig correctl. If the light is ON or OFF all the time, the there could be a problem (see page 42 for details). 23: Curret Readig Pads To calculate the curret draw of the cotrol pael, measure the voltage across the two pads ad multipl b 10 i.e. Readig = 34mV (x10) = 340mV = 340mA. 24: NVM 1 & 2 All sstem programmig data ad the evet log is stored i oe or two o-volatile memor devices. F1 - F5: Protectio Fuses (48, 88 ad 168) The followig fuses are provided: F1 (1Amp) Auxiliar 12V Power fuse F2 (1.6 Amp) Batter fuse (electroic PTC) F3 (1 Amp) Network 1 fuse F4 (1 Amp) Bell/Strobe fuse F5 (1 Amp) Network 2 fuse (168 ol) INS

16 Istallatio Premier Elite 640 PCB Laout Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual C om 3 Box Tamp 13.7V DC 2.5A max L /M + - B AT T F3 F15 F2! US E W IT H TEXECOM PSU O NLY BAR C ODE 100mV = 1Amp V F1 J p1 J p2 N/ O C O M N /C O P5 O P4+ O P2- R/R DC+ DC- 1 DIGIC OM OUTP UTS F5 F ault He ar tbe at K ick S ta rt Load Defaul ts Tx F9 Rx E xp as io F ault Tx C om 1 C om 2 Jp9 Rx F ault Tx Rx P rogrammig Po rt F ault Tx Rx F ault Tx Rx F ault Tx Rx F ault Tx Rx F ault F6 Tx E able S moke F4 JP10 Bell 12V E a ble Rx O P3+ O P Aux 12V S pk - S pk+ Aux/ Fault + 12v Bell - Tamp 0v S trb - E g i e ers K e pa d F T R NET WOR K 1 F7 + - T R NET WOR K 2 F8 + - T R NET WOR K 3 F9 + - T R NET WOR K 4 F T R NET WOR K 5 F T R NET WOR K 6 F T R NET WOR K 7 F T R NET WOR K 8 Bell/S pk Aux 12V Fa ult Fa ult 1: Texecom PSU Coectio Coected to the Texecom Switch Mode Power Suppl. DO NOT CONNECT THE MAINS SUPPLY TO THE AC INPUT TERMINALS ON THE PCB. 2: Batter Coectios A 12V rechargeable batter must be coected to these termials i order to provide cotiuous sstem operatio i the evet of a AC Mais failure (see page 19 for details). 3: Digicom Power & Iputs These termials provide ufused power; remote reset ad lie fault iputs ad are ormall used for coectig a stad-aloe commuicator to the cotrol pael (see page 34 for details). 4: Digicom Outputs Outputs 1 to 8 are low curret (100mA -ve applied) ad would ormall be used whe coectig a stad-aloe commuicator to the cotrol pael (see page 34 for details). Each output is full programmable (see page 77 for details). 5: Egieers Kepad A portable Egieers kepad ca be plugged o here to allow easier access for programmig ad testig. Whe usig a kepad as a Egieers kepad, the address must be set to 10 (see page 22 for details). The kepad zoes ad lid tamper are ot moitored. 6: Network Data Coectios Networks 1-8 provide coectio for the kepads ad zoe expaders. The + ad termials provide power whilst the T trasmits data ad R receives data (see page 20 for details). 7: Exteral Souder Coectios These termials are used for coectig to a exteral souder uit (see page 33 for details). 8: Auxiliar/Fault Coectios These termials ca be used for moitorig the tamper loop of a auxiliar device (see page 33 for details). 9: Loudspeaker Coectios These termials ca be used for coectig up to oe 16Ω or two 8Ω loudspeakers (see page 33 for details). 10: Auxiliar 12V Power These termials are for coectig devices that require 12V power (protected b a 1A fuse). 11: Pael Outputs Outputs 1 & 2 are 500mA -ve applied, outputs 3 & 4 are 500mA +ve applied ad output 5 is a clea cotact rela (see page 34 for wirig details). These outputs are all full programmable (see page 76 for details). 12: Plug-o Commuicator Coectios This socket provides coectio for the plug-o commuicator (see page 36 for details). 13: Box Tamper Coectio The box tamper micro switch is coected here. The micro switch provides tamper protectio for the mai cotrol pael i case of uauthorised access. To disable the box tamper, remove the micro switch lead ad fit a jumper lik across the two pis. 14: Com Port 3 Com Port 3 is a serial commuicatios port ad ca be used for coectig a PC ruig Witex or a supported serial device to the cotrol pael (see page 94 for details). 15: Plug-o RedCARE/Dualcom Coectios These pis provide coectios for a plug-o RedCARE, Dualcom, Digicom or RM8 Rela module. Each output is full programmable (see page 77 for details). Whe a device is plugged o to these pis, ot all outputs ma be available, please refer to the relevat documetatio for details. 16: NVM 1 & 2 All sstem programmig data ad the evet log is stored i oe or two o-volatile memor devices. 17: Flash Upgrade Port For use with the Flasher iterface to update pael firmware. 16 INS176-9

17 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 18: Commuicatio Ports 1&2 Com Port 1 is a serial commuicatios port ad ca be used for coectig a PC ruig Witex or a supported serial device to the cotrol pael (see page 94 for details). Com Port 2 is a serial commuicatios port ad ca be used for coectig a PC ruig Witex or a supported serial device to the cotrol pael (see page 94 for details). 19: Expasio The Expasio Port ca be used for coectig a 60XiD Zoe Expader (see page 32 for details) or a AV Module (see page 40 for details), X-10 Module or a Memor Module. 20: Load Defaults Butto Press ad hold this butto whilst applig power to the cotrol pael to load the factor default settigs. Press ad hold this butto for 7 secods with power alread o the pael to restore just the Egieer code to the factor settig of. Loadig the factor defaults ca take up to 60 secods to complete. Loadig defaults will ol be possible if the NVM has ot bee locked (see page 64 for details). 21: Heartbeat LED/Power Light Flashes steadil to idicate that the cotrol pael is fuctioig correctl. If the light is ON or OFF all the time, the there could be a problem (see page 42 for details). Istallatio 22: Batter Kick-start Butto Whe powerig up the pael without AC Mais preset, this butto must be pressed i order to coect the batter. If AC Mais is preset this butto does ot eed to be pressed. 23: Curret Readig Pads To calculate the curret draw of the cotrol pael, measure the voltage across the two pads ad multipl b 10 i.e. Readig = 34mV (x10) = 340mV = 340mA. F1 F14: Protectio Fuses The followig electroic fuses are provided: F3 (1600 ma) Batter F4 (250mA) Speaker F5 (900mA) Network 1 F6 (900mA) Bell/Strobe F7 (900mA) Network 2 F8 (900mA) Network 3 F9 (900mA) Network 4 F10 (900mA) Network 5 F11 (900mA) Network 6 F12 (900mA) Network 7 F13 (900mA) Network 8 F14 (900mA) Auxiliar 12V INS

18 Istallatio Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Power Suppl Ratigs If istallig to EN50131 or PD6662, the sstem stadb times i the evet of a mais power failure var depedig o the grade ad how AC fail is sigalled: Whe calculatig the curret cosumptio of the sstem ou must iclude the curret take b the cotrol pael ad all the devices that it powers. If the total curret exceeds the Rated Output for the grade ou are istallig to the a additioal power suppl is required Premier Elite 24 (Metal) Curret Curret Cosumptio 95mA Maximum Curret Available 0.75A charge 1.0A 0.3A charge 1.9A Rated Output Batter Arragemet Batter Rated Output (Amps) Charge 12h 24h 30h 60h 1 x 7Ah 0.3A 0.48A 0.19A 0.13A 0.021A 1 x 17Ah Stadb ad Recharge Times 0.3A 1.32A 0.61A 0.47A 0.18A 0.75A 1.0A 0.61A 0.47A 0.18A EN Grade 1 Grade 2 Grade 3 Miimum Stadb 12h 12h 30h * Period Maximum Recharge 72 Hrs 72 Hrs 24 Hrs Time PD6662 Grade 1 Grade 2 Grade 3 Stadb Period 12 Hrs 12 Hrs 24 Hrs ** Maximum Recharge 72 Hrs 72 Hrs 24 Hrs Time *30h if MAINS FAIL is reported to ARC, otherwise 60h **This time ma be halved if mais failure is sigalled to a ARC Jumper Settigs Batter Arragemet Recharge Time Batter Charge Selector 1 x 7Ah < 24Hrs 0.3 A < 24Hrs 0.75 A 1 x 17Ah < 72Hrs 0.3 A Premier Elite 24 (Polmer) Curret Curret Cosumptio 95mA Maximum Curret Available 0.3A charge 1.1A Rated Output Batter Rated Output (Amps) 12h Batter Arragemet Charge 1 x 7Ah 0.3A 0.48A Stadb ad Recharge Times EN Grade 1 Grade 2 Miimum Stadb Period 12h 12h Maximum Recharge Time 72 Hrs 72 Hrs PD6662 Grade 1 Grade 2 Stadb Period 12 Hrs 12 Hrs Maximum Recharge Time 72 Hrs 72 Hrs Premier Elite 48/88/168 Curret Curret Cosumptio 125mA Maximum Curret Available 0.75A charge 1.0A 0.3A charge 1.9A Rated Output Batter Rated Output (Amps) 12h 24h 30h 60h Batter Arragemet Charge 1 x 7Ah 0.3A 0.458A 0.166A 0.108A 1 x 17Ah 0.3A 1.29A 0.583A 0.441A 0.158A 0.75A 1.0A 0.583A 0.441A A Stadb ad Recharge Times EN Grade 1 Grade 2 Grade 3 Miimum Stadb 12h 12h 30h * Period Maximum Recharge 72 Hrs 72 Hrs 24 Hrs Time PD6662 Grade 1 Grade 2 Grade 3 Stadb Period 12 Hrs 12 Hrs 24 Hrs ** Maximum Recharge 72 Hrs 72 Hrs 24 Hrs Time *30h if MAINS FAIL is reported to ARC, otherwise 60h **This time ma be halved if mais failure is sigalled to a ARC Jumper Settigs Batter Arragemet Recharge Time Batter Charge Selector 1 x 7Ah < 24Hrs 0.3 A < 24Hrs 0.75 A 1 x 17Ah < 72Hrs 0.3 A Premier Elite 640 Curret Curret Cosumptio 125mA Maximum Curret Available 0.75A charge 1.0A Rated Output Batter Batter Rated Output (Amps) Arragemet Charge 12h 24h 30h 60h 1 x 17Ah 0.75A 1.0A 0.558A 0.416A 0.133A Stadb ad Recharge Times EN Grade 1 Grade 2 Grade 3 Miimum Stadb 12h 12h 30h * Period Maximum Recharge 72 Hrs 72 Hrs 24 Hrs Time PD6662 Grade 1 Grade 2 Grade 3 Stadb Period 12 Hrs 12 Hrs 24 Hrs ** Maximum Recharge 72 Hrs 72 Hrs 24 Hrs Time *30h if MAINS FAIL is reported to ARC, otherwise 60h **This time ma be halved if mais failure is sigalled to a ARC Premier Elite 24-W & 48-W Curret Curret Cosumptio 150mA Maximum Curret Available 0.3A charge 1.0A Rated Output Batter Rated Output (Amps) 12h Batter Arragemet Charge 1 x 7Ah 0.3A 0.433A Stadb ad Recharge Times EN Grade 1 Grade 2 Miimum Stadb Period 12h 12h Maximum Recharge Time 72 Hrs 72 Hrs PD6662 Grade 1 Grade 2 Stadb Period 12 Hrs 12 Hrs Maximum Recharge Time 72 Hrs 72 Hrs 18 INS176-9

19 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Istallatio Coectig AC Mais The AC Mais suppl is coected to a 3 wa Euro Tpe fused termial block, which is fitted with a 3.15A medium/slow blow fuse. All other wirig MUST be carried out before AC mais is coected to the cotrol pael. After coectig the AC Mais, fit the mais cover, this ca be foud i the spares bag. FUS E 3.15A To P S U L E N Coectig Batteries If istallig to PD6662: 2004 the ol Oe 12V 7Ah batter or 12V 17Ah batter ca be fitted iside the cotrol pael to provide cotiued operatio i the evet of a AC mais failure, otherwise, two 12V 7Ah batteries ca be coected. All other wirig MUST be carried out before the batter is coected to the cotrol pael. Coect the red batter lead to the positive termial of the batter ad the coect the black batter lead to the egative termial. The pael will ol become live whe the AC Mais is coected or the Batter Kick-start butto is pressed. Two batteries ca be fitted ad still compl with PD6662:2004 if the Batter Splitter is used. INS

20 Istallatio Coectig Devices to the Network Before coectig kepads, zoe expaders ad output modules, isolate ALL power from the cotrol pael (AC Mais & Batter). Do ot cotiue if there is still power preset o the cotrol pael. Coectig devices with power still preset o the cotrol pael ma damage the device or cotrol pael ad ivalidate a warrat. Kepads, zoe expaders ad output modules are all coected to the same etwork termials located at the bottom left had corer of the cotrol pael ad ma be coected seriall (dais chai), i parallel (star) or a combiatio of the two (see Figure 1, page 21 for details). No more tha 8 zoe expaders, 8 kepads ad 4 output modules ca be coected to each etwork. The maximum umber of devices that ca be coected i total will deped o the cotrol pael fitted. Wheever ew devices are coected to the etworks, the must be cofirmed oto the sstem usig the Cofirm Devices meu optio (see page 117 for details). Wirig the Network The etworks are made up of four termials icorporatig power ad data. To esure correct operatio, all four termials o the device must be coected to the correspodig termials o the cotrol pael, or previous device (see Figure 1, page 21 for details). The table below shows each termial ad its descriptio: Termial Descriptio + +12V Suppl - 0V Suppl T Trasmit Data R Receive Data Devices ca be coected usig 4-core cable. However, it is recommeded that 6 or 8-core cable is used as the spare cores ca be used to Double Up o the power coectios if eeded. Stadard 7/0.2 alarm cable ca be used for most istallatios. However, uder certai coditios it ma be ecessar to use screeed cable. Cable Distaces The maximum recommeded distace for devices whe usig stadard 7/0.2 alarm cable is: 250m for each brach whe usig the star (parallel) cofiguratio Whe usig a dais chai (series) cofiguratio the maximum distace will deped o the umber of devices coected o the chai. The more devices that are coected, the shorter the distace to the last device (this is due to voltage drop i the cable) Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Whichever method of wirig cofiguratio is used, esure that the voltage betwee the + ad termials at each device is o lower tha 10.0V whe the sstem is ruig o the stadb batter. The table below shows maximum cable rus whe oe kepad or expader is istalled usig stadard 7/0.2 alarm cable with various loads: Cofiguratio Max. Cable Ru 1. Kepad + 2 PIR 250m 2. Expader + 2 PIR 250m 3. Expader + 8 PIR 100m 4. As No Ω Speaker 30m Distaces of up to 1km ca be achieved betwee the cotrol pael ad a device. However, a power suppl must be istalled close to the device to power it locall, this will help to overcome voltage drop caused b the log cable ru. Overcomig Voltage Drop There are several was to overcome voltage drop: Use thicker lower resistace cable. Stadard 7/0.2 alarm cable has a resistace of 8Ω per 100m Double up o the power coectios this will require usig a 6 or 8-core cable rather tha a 4-core cable Istall a power suppl to power the device locall, remember to commo the two egative coectios Istallig a Power Suppl Whe a power suppl is istalled, the 0V coectios o the power suppl must be coected through to 0V o the cotrol pael ad the +12V coectio betwee the cotrol pael ad the device must be discoected (see Figure 2, page 21 for details). Network Diagostics Each etwork has two LED s to idicate data flow. The red LED idicates data flowig out of the T termial ad the gree LED idicates data flowig ito the R termial. The table below shows each LED status ad its meaig: LED Status T Wire OUT T Wire IN Red LED Flashig Normal Normal Red LED O Pael Fault Cable Short Red LED Off Pael Fault Pael Fault LED Status R Wire OUT R Wire IN Gree LED Flashig Pael Fault Normal Gree LED O Pael Fault Cable Short Gree LED Off Normal No Data From Devices The LED s are provided as a aid for fault fidig ad therefore should ot be completel relied upo to idicate that there is a fault. 20 INS176-9

21 + Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Istallatio Figure 1: Network Coectios (250m without additioal power suppl). Premier K epad C otrol P a el Network 1 or 2 Ne tw or k T R m Premier K epad Premier Zoe E xpader T Ne tw or k + R T Ne tw or k + R - T R Premier K epad T R Ne tw or k T - R T R Ne tw or k Premier Output Module To a dditioal Kepa ds, Zoe E xpa ders or Output Modules 25 0 m Figure 2: Network Coectios (1km with additioal power suppl). 1 km C otrol P a el Network 1 or 2 Ne tw or k T R - Premier K epad Premier K epad T Ne tw or k + R T Ne tw or k + R - Premier Zoe E xpader Premier K epad T N ET WO R K IN + R NET WOR K OUT T R - Ne tw or k T - R D iscoe ct + 12 V fro m c otrol pael + - T R Ne tw or k Premier Output Module + - P ower S u ppl To a dditioal Kepa ds, Zoe E xpa ders or Output Modules INS

22 Istallatio Remote Kepads Kepad Laout Addres s S witc h Ta mp er S witc h S peaker Ou tput Coectig Kepads Ou tput - N etwor k Termia ls P ie z o S oud er Zo es Kepads are coected to the etwork termials located at the bottom left had corer of the cotrol pael (see pages 20 & 21 for details). Kepad Addressig Each kepad must be assiged a differet address usig the DIL switches located o the left had side of the PCB. The table below shows the kepad addressig: 2 Address DIL 1 DIL 2 DIL 3 DIL 4 1 O or off Off Off Off Off O Off Off 3 Off Off O Off 4 Off Off Off O Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Zoe Numberig The table below shows the zoe allocatio whe the kepads are istalled: Address Zoes (Network 1) Zoes (Network 2) 1 Umapped Umapped 2 Umapped Umapped 3 Umapped Umapped 4 Umapped Umapped 5 * Umapped Umapped 6 * Umapped Umapped 7 * Umapped Umapped 8 * Umapped Umapped Address Zoes (Network 3,4 & 5) Zoes (Network 6 7 & 8) 1-8 ** Umapped Umapped The zoes iside the kepads are ot see b the sstem util the have bee mapped to a zoe umber (see page 73 for details). * ol ** 640 ol Kepad Output The remote kepad has oe programmable output, which ca be used to drive auxiliar devices such as LED s, souders or relas etc. Wire as per Pael Outputs show o page 34 (see page 76 for details). The electrical characteristics for the output are show below: Output Max Curret Tpe 1 100mA Switched -ve 5 * O Off Off O * Off O Off O * Off Off O O * O Off O O Egieers O O O O Never set two kepads o the same etwork to the same address. Whe usig a kepad as a Egieer s kepad, the DIL switches must all be O. * & 640 ol Kepad Zoes The kepad has two programmable zoes (see page 31 for details). Each zoe is also full programmable (see page 48 for details). Kepad Speaker Output (LCDL/LCDLP Ol) The LCDL ad LCDLP kepads have a output that ca be used for drivig up to oe 16Ω or two 8Ω loudspeakers (see page 33 for details). The speaker volume is also full adjustable (see page 73 for details). Programmable Ifo. LED The Ifo. LED o the frot of the kepad ca be programmed to mimic the kepad output or show the armed status of a area (see page 73 for details). Adjustable Backlightig To adjust the kepad backlightig press the YES ke for 5 secods, the with the YES ke still pressed use to icrease or decrease the backlightig util the required brightess is achieved, the release both kes. The backlight ca ol be adjusted whe the kepad is ot i a meu. Kepad Lid Tamper The lid tamper of each kepad ca be disabled if required usig the relevat kepad optio i the Kepad Setup meu (see page 73 for details). 22 INS176-9

23 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 8XP-W & 32XP-W V2.xx> Ricochet MT2 The Premier Elite Series of cotrol paels have bee upgraded to V2.xx firmware which ow cotais Ricochet MT2 capabilit. This ew techolog adds additioal features ad fuctios for Ricochet eabled securit sstems. The Expaders used must be Premier Elite XP-W V2.xx. DO NOT mix V1 & MT2 expaders o the same Premier Elite pael Multiple Expader Support It is ow possible to add multiple expaders to the sstem allowig for greater flexibilit i sstem desig, ad also takig wireless capabilit to ew levels. Additioal device modes ad diagostics fuctios also give more iformatio about the sstem status, ad allow greater cotrol over devices modes of operatio. Cotrol Pael Capacit The table below details the maximum umber of expaders, devices ad Premier Elite SmartKe that ma be used o the differet cotrol paels, other cofiguratios ma be possible b mixig Premier Elite 32XP-W & Premier Elite 8XP-W. Pael Expaders Devices 32XP-W Premier Elite SmartKe Expaders Devices 8XP-W Premier Elite SmartKe Premier Elite Premier Elite Premier Elite N/A 48-W N/A N/A N/A Premier Elite Premier Elite Premier Elite Istallatio established correctl. Please refer to the relevat sectio i this documet to Lear Devices to the sstem. Learig Premier Elite SmartKe O Ricochet MT2 sstems Premier Elite SmartKe should ol be leared AFTER all devices ad expaders are i their fial locatio, this is critical o larger sstems where multiple expaders are beig used Devices should be at least 30cm s awa from the receiver whe beig leared. Placig Devices Oce all of the devices have bee leart, the will eed placig i their desired locatio, this should be doe b istallig devices closest to the expader first ad the workig outwards so that the last devices istalled are those furthest awa from the expader. Make sure to istall devices with the expader i Commissio mode. See INS467 for details Devices also have a commissio mode which will idicate a secure ad valid path of commuicatio to the receiver. See INS467 for details You should wait at least 15 miutes after istallig the last device to make sure routig has bee correctl established betwee all sstem devices. For maximum reliabilit ad sstem itegrit avoid log ad thi set-ups. Devices are capable of hoppig through up to two other devices, or a maximum of three hops. PCB Laout Premier Elite 32XP-W take 4 address slots o the etwork, Premier Elite 8XP-W take oe address To eable all of the advaced fuctioalit ad diagostics capabilit Ricochet MT2 the followig are miimum requiremets:- Witex Versio 6 Build 16 or later Ricochet Moitor or later Premier Elite Series V2.xx or later Premier Elite 32XP-W & 8-W Expaders V2.xx or later ON ON Sstem Desig Cosideratios To esure correct setup ad operatio of the Wireless Network it is importat that the followig procedures are used whe learig ad placig devices. Multiple Expader Sstems Ricochet MT2 Whe usig multiple expaders great care should be take whe desigig the sstem. Each expader should be treated as its ow wireless etwork; it is ot possible for devices to hop from oe wireless etwork to the other, it is also ot possible for expaders to pass wireless sigals from devices ot assiged to them ad or ca the expaders talk to each other. Learig Devices All devices should be leart before the are placed i their fial locatio. The expader should be i commissio mode, please see INS467 for details. This will esure that the are registered o the receiver or cotrol pael, ad that Mesh Networks ad routig are INS

24 Istallatio 1: Egieers Kepad Coectio A egieer s kepad (Premier/Elite LCD kepad ad iterface lead) ca be temporaril plugged oto this coector to allow sstem programmig ad testig. (Fuctios depedet o Pael firmware versio) Set the kepad address switches to all o. 2: Network Coectio The + ad termials provide power whilst the T ad R termials are trasmit ad receive data. 3: For Future Use 4: Comm. Port Coectio Serial commuicatios port for coectig the 8 XP-W & 32XP-W to a PC via PC Com/USB Com or Com IP for use with RICOCHET Moitor Software. 5: Lid Tamper Whe ope puts the sstem ito commissio mode ad digitall atteuates the receiver sigal b 15Db. 6: Programmig LED s Allows programmig of devices directl to the receiver, i cojuctio with the lear switch. 7: Atea RF Atea. Premier 32XP-W = 2 x Atea Premier 8XP-W = 1 x Atea 8: Network LED's Gree LED = Data received b the expader from the pael Red LED = Data trasmitted b the expader to the pael. (The flash rate depeds o the mode ad RF activit) Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 9: Heartbeat LED Flashes steadil to idicate that the receiver is fuctioig correctl. If the light is ON or OFF all the time, the there could be a hardware problem. 10: Lear Switch To be used with programmig LED s to lear devices directl to the receiver. 11: Optios Switch Use to select the receiver fuctioalit depedig o pael firmware. Switch 1 ON =firmware depedat, please see the relevat programmig sectio. Switch 2 ON = Legac Mode OFF = RICOCHET Switch 3 ON = Impaq Cotact-W Wired Iput 2 will report as Tamper (default) OFF = iput 2 will report as a Alarm. Switch 4 Walk test 12: Address Switch Used to assig the address of the receiver o the premier etwork 13: RF LED Flashes whe trasmittig or receivig RF data 14: Tamper Disable Disables the lid ad rear tamper 15: Egieer s Kepad LED's Red LED flashes costatl, the flash rate icreases whe data is beig trasmitted. 16: Flash Programmig Port Variat depedet, for flashig the expader with updated firmware. Ricochet MT2 Expader Addressig Itroductio The address rage ad switch positio will deped o which combiatio of expaders are beig used. Each 32XP-W takes up 4 address slots o the cotrol pael etwork, however the etwork slots are virtual util devices are assiged to available zoes. It is possible that if a 32XP-W is beig used at Address 1, but ol 16 devices have bee used, Address 3 & 4 are available for hardwired 8XP's or 8XP-W's. Please see some examples of mixig differet tpes of Expaders o various Elite paels ad the addressig requiremets. Example 1 Totall wireless sstem(s) Pael Expaders (Max) Premier Elite 88 Expader Address Premier Elite 168 Expader Address Premier Elite 640 Expader Address 32XP-W Network 1 Network 2 Network 3 Network 4 Network 5 Network 6 Network 7 Network Exp 1 Exp 2 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 1 5 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Exp 1 Exp 2 Exp 1 Exp 2 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Exp 1 Exp 2 Exp 1 Exp 2 Exp 1 Exp 2 Exp 1 Exp 2 Exp 1 Exp 2 Exp 1 Exp 2 Exp 1 Exp 2 Exp 1 Exp Example 2 Premier Elite 168, + 32XP-W, 8XP-W's & 8XP's mix Pael Network 1 Network 2 Expaders (Wireless) Expaders (Mixed) Premier Elite XP-W 2 x 8XP-W 8XP-W 8XP-W 8XP 8XP Expader Address 1 5 & Devices (Max) Premier Elite SmartKe (Max) N/A N/A Example 3 Premier Elite 48, 32XP-W + 8XP's Pael Network 1 Expaders (Mixed) Premier Elite 48 32XP-W 2 x 8XP Expader Address 1 5 & 6 Devices Used Premier Elite SmartKe (Max) 16 N/A 24 INS176-9

25 + Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Istallatio 8XE Zoe Expader (24 Ol) The 8XE Zoe Expader has: 8 full programmable zoes Aux 12V Output Expader Laout 8XP Zoe Expader Expader Laout Ta mper S wi tc h E gieers Kepad Ite rfa c e Network Termials Power LED Z9 Z10 Z11 Z12 Z13 Z14 Z15 Z A ux12 Zoes 9-16 or Tampers 1-8 Coectig Expaders Aux 12V (1 Amp) C oector for pluggig o J P5 cotrol pael The 8XE local zoe expader plugs directl o to the termials located o the right had side of the cotrol pael (see below for details). To istall the local zoe expader proceed as follows: 1. Esure that all power is removed from the cotrol pael (mais ad batter) before attemptig to fit the expader. 2. Push the four support pillars (supplied) ito the four locatig holes o the cotrol pael PCB. 3. Alig the local expader coector with the 8 wa plug (JP5) o the cotrol pael. Push expader ito place, esurig that all four pillars clip ito the four locatig holes o the local expader. Zoes 1 & 2 Aux 12V Zoes 3 & 4 A T A T - A T A T Z o e 1 Z o e 2 Z o e 3 Z o e 4 Com Port Aux Iput + - T R + - T R D S - - S peaker Output Coectig Expaders O utputs 1 to 8 A T A T - A T A T Z o e 8 Z o e 7 Z o e 6 Z o e 5 Addres s S wi tc h Zoes 5 & 6 Aux 12V Zoes 7 & 8 Expaders are coected to the etwork termials located at the bottom of the cotrol pael (see pages 20 & 21 for details). Expader Addressig Each Expader must be assiged a differet address usig the DIL switches located i the cetre of the PCB. The table below shows the expader addressig: Address DIL 1 DIL 2 DIL 3 DIL 4 1* O or off Off Off Off 2* Off O Off Off 3** Off Off O Off 4** Off Off Off O Zoe Numberig The table below shows the zoe allocatio whe the expaders are istalled: Cofiguratio Pael Zoes Expader Zoes 8XE = Zoes 1 to 8 9 to 16 8XE= Tampers 1 to 8 Tampers 1 to 8 Expader Zoes The expader has eight programmable zoes (see page 31 for wirig details). Each zoe is also full programmable (see page 48 for programmig details). 5*** O Off Off O *** Off O Off O *** Off Off O O *** O Off O O Never set two expaders o the same etwork to the same address. * 24/48/88/168/640 ** 48/88/168/640 ol *** & 640 ol Expader Zoes The expader has eight programmable zoes (see page 31 for wirig details). Each zoe is also full programmable (see page 48 for details). INS

26 Istallatio Star ad Dais Jumper Optio The PCB has a jumper JP3 which allows ou to select either STAR (S) or DAISY (D) wirig cofiguratio. The jumper should be set as follows: If the etwork IN coectio is wired i parallel with a other device the jumper MUST be set to the S positio. All previous versios of the expader operated i this mode ad for backward compatibilit the uit is supplied with the jumper i this positio. If the etwork IN coectio is ol wired to oe device the jumper should be set to the D positio. Whe the jumper is set to the STAR positio the etwork data sigals are ot boosted betwee expader ad the previous device. I this mode the etwork cablig MUST ot exceed 100m betwee devices. Whe the jumper is set to the DAISY positio the etwork data sigals are boosted betwee the expader ad the previous device. This mode will allow expaders o the etwork to be coected up to 250m apart ad MUST ol be selected if the expader has oe device coected to the etwork IN coectios. Star wirig example Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Zoe Numberig (24/48/88/168) The table below shows the zoe allocatio whe the expaders are istalled: Address Zoes (Network 1) Zoes (Network 2) 1* * ** ** *** *** *** *** Network 2 ca ol be used o the 168. For 640 see page 30 * 24/48/88/168/640 ** 48/88/168/640 ol *** & 640 ol Expader Auxiliar Iput The expader has oe programmable iput. This auxiliar iput ca be used to moitor auxiliar devices such as tamper loops etc. Wire as per Aux Tamper show o page 32 (see page 75 for details). The sstem will respod as follows: Dais chai wirig example Combied Wirig example Iput Status Sstem Respose 0V Applied Iput Secure 0V Removed Iput Active EOL Various * For further details o how the iput status affects the sstem please refer to page 75. * For wirig details, see page 35. Expader Outputs The zoe expader has eight programmable outputs, which ca be used to drive auxiliar devices such as LED s, souders or relas etc. Wire as per Pael Outputs show o page 34 (see page 76 for details). The electrical characteristics for the outputs are show below: Outputs Max Curret Tpe 1 to 8 100mA Switched -ve Expader Speaker Output The expader has a output that ca be used for drivig up to oe 16Ω or two 8Ω loudspeakers (see page 33 for details). Expader Com Port The Com Port ca be used to coect a PSU200 or amoitored power suppl. Expader Lid Tamper The lid tamper of each expader ca be disabled if required b fittig a jumper lik across the cetre ad right had pis of the Eable Tamper pis (JP2) leavig the left had pi free. These pis are located to the left of the address DIL switch just beeath the fuse. 26 INS176-9

27 + Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Istallatio iprox Module iprox Laout O ptio & Addre ss S witches OP16 Output Expader Output Module Laout Tamper Iteral Souder Off O Networ k Termials Aux 12V ad Tamper Ou tput Networ k Termials ON S pe aker Termi als W ieg ad I terfa c e C o ectio s Ne tw ork Termi als D0 Spk + D1 + T R Address ON Optios Ext It Ext It P IP Ext Coil L1- L2- L+ RTE N/C N/O Com C1 C2 Remote LED s Rela 1 Do or S trike R ela Request to E xit I p ut R emo te Prox Coil C o ectio s Eg ieers Kepad Iterfa c e B a k 1 O utputs 1 to 8 Ta mp er S witc h T R + - T R BAR C ODE B a k 2 O utputs 1 to 8 Coectio S pe aker Volume Adj The iprox Module is coected to the etwork termials located at the bottom of the cotrol pael (see pages 20 & 21 for details). Addressig The iprox Module is addressed as a kepad ad will occup a kepad slot o the etwork. The uit must have a uique address, which must ot coflict with kepad or a other iprox Module o the same etwork The followig table shows the addressig: Address DIL 1 DIL 2 DIL 3 DIL O or off Off Off Off 2 Off O Off Off 3 Off Off O Off 4 Off Off Off O * O Off Off O * Off O Off O * Off Off O O * O Off O O Coectig Output Modules Po wer L E D Output modules are coected to the etwork termials located at the bottom left had corer of the cotrol pael (see pages 20 & 21 for details). Output Module Addressig Each output module must be assiged a differet address usig the DIL switches located i the cetre of the PCB. The table below shows the expader addressig: Address DIL 1 DIL 2 DIL 3 DIL 4 1 O or off Off Off Off 2 2 Off O Off Off 2 3* Off Off O Off 2 4* Off Off Off O Never set two modules o the same etwork to the same address. *88/168 & 640 ol Refer to the iprox Module maual for programmig ad operatig istructios. 60iXD Zoe Expader The 60iXD expader provides the followig facilities: Two id loops each supportig up to 30 biscuits Fused 12V output for powerig detectors Egieer s kepad port for local id diagostics 5 ** O Off Off O ** Off O Off O ** Off Off O O ** O Off O O * 88 ad 168 ol ** 168 ol I order for a output module to mimic zoe expader outputs, the output module must be addressed the same as the zoe expader that it is mimickig. A combiatio of addresses ca be used o each output module i.e. Bak 1 ca be addressed to mimic expader 3 ad Bak 2 ca be addressed to mimic expader 8. Bak 1 switch sets the address of the device that Bak 1 outputs 1 to 8 will mimic. Bak 2 switch sets the address of the device that Bak 2 outputs 1 to 8 will mimic. INS

28 Istallatio Output Module Numberig The table below shows the output allocatio whe the output modules are istalled, Address Outputs (Network 1) Outputs (Network 2) ** 1 Expader 1, 1-8 Expader 1, Expader 2, 1-8 Expader 2, * Expader 3, 1-8 Expader 3, * Expader 4, 1-8 Expader 4, ** Expader 5, 1-8 Expader 5, ** Expader 6, 1-8 Expader 6, ** Expader 7, 1-8 Expader 7, ** Expader 8, 1-8 Expader 8, 1-8 Network 2 ca ol be used o the 168 * 88 ad 168 ol ** 168 ol for 640 see page 30 Outputs The output module has 16 programmable outputs, which ca be used to drive auxiliar devices such as LED s, souders or relas etc. Wire as per Pael Outputs show o page 34 (see page 76 for details). The electrical characteristics for the outputs are show below: Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Istallatio Before attemptig to istall the RM8 Rela Module, isolate ALL power from the cotrol pael (AC Mais ad Batter). Do ot cotiue if there is power still preset o the cotrol pael. Pluggig o the Rela Module with power still preset o the cotrol pael ma damage the Rela Module, cotrol pael or both ad ivalidate a warrat. Pluggig o the Rela Module 1. Esure that the Rela Module is the correct wa up (see page Error! Bookmark ot defied.). 2. Getl press dow o the Rela Module util the rela Module is seated correctl. 3. Recoect power to the cotrol pael. Testig o the Rela Module 1. For plug o operatio, test the Rela Module i accordace with the cotrol pael istructios. 2. To test the auxiliar iputs, appl 0V to each iput i tur ad esure that the correct LED illumiates ad a click is heard from the rela. Coectig Outputs The RM8 Rela Module has 8 outputs. These outputs ca be used to drive auxiliar devices such as LED s, souders or commuicators etc. Each output is a clea cotact rela rated at 12V. The diagram below shows tpical wirig examples for the outputs: Premier RM8 R ela Module Bak Outputs Max Curret Tpe 1 1 to 8 100mA Switched -ve 2 1 to 8 100mA Switched -ve Tamper Output The tamper switch o the output module is coected to the tamper output at the top of the module. If moitorig of the lid tamper is required, this output must be coected to a suitable iput o the cotrol pael or zoe expader. RM8 Rela Module The Premier Elite RM8 Rela Module is compatible with a cotrol paels that have a plug o RedCARE/Dualcom footprit. Features 8 rela outputs (12V, 3Amp each) 8 Auxiliar iputs (-ve applied) Auxiliar 12V output (protected b a 1 Amp fuse) Rela ON idicatio via LED s Coectig Iputs The RM8 Rela Module has 8 auxiliar iputs. These iputs ca be used to activate the relas from a exteral source. Each iput is -Ve applied ad draws up to 30mA. The diagram below shows tpical wirig examples for the iputs: P remier R M8 R ela Module Ve Outputs from exteral S ource Outputs PCB Laout Auxiliar Iputs 1-8 (-ve applied) F1 Rela ON Idicators LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 1 Amp Aux 12V Fuse 1 Amp R LY1 R LY2 R LY3 R LY4 R LY5 R LY6 R LY7 R LY8 R ela Outputs 1-8 Aux 12V 28 INS176-9

29 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Istallatio Zoe ad Output Numberig 24/48/88/168 Expader Zoes Kepad Zoes Address Zoes (Network 1) Zoes (Network 2) Address Zoes Network 1 Zoes Network Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped Kepad Zoes Address Zoes Network 1 Zoes Network 2 Zoes Network 3 Zoes Network 4 Zoes Network 5 Zoes Network 6 Zoes Network 7 Zoes Network 8 1 Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped 2 Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped 3 Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped 4 Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped 5 Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped 6 Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped 7 Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped 8 Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped Expader/OP16 Outputs Address Outputs Network 1 Outputs Network 2 Outputs Network 3 Outputs Network 4 Outputs Network 5 Outputs Network 6 Outputs Network 7 Outputs Network 8 1 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8 INS

30 Istallatio Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Zoe ad Output Numberig 640 Expader Zoes Address Zoes Network 1 Zoes Network 2 Zoes Network 3 Zoes Network 4 Zoes Network 5 Zoes Network 6 Zoes Network 7 Zoes Network Kepad Zoes Address Zoes Network 1 Zoes Network 2 Zoes Network 3 Zoes Network 4 Zoes Network 5 Zoes Network 6 Zoes Network 7 Zoes Network 8 1 Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped 2 Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped 3 Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped 4 Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped 5 Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped 6 Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped 7 Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped 8 Umapped Umapped Umapped Umapped Umapped Umapped Umapped Umapped Expader/OP16 Outputs Address Outputs Network 1 Outputs Network 2 Outputs Network 3 Outputs Network 4 Outputs Network 5 Outputs Network 6 Outputs Network 7 Outputs Network 8 1 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, INS176-9

31 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Zoe Coectios A zoes that are ot beig used must be liked out or programmed as Not Used (see page 48 for details). Whe usig Ed Of Lie wirig, ol 1 device should ormall be coected to each zoe. Triple Ed Of Lie (TEOL) Istallatio Use this wirig cofiguratio whe coectig PIR devices with that require Ati Mask ad Fault detectio. Several zoe wirig programmig optios are available for this, Triple EOL is illustrated below. See Zoe Wirig o page 53. A zoe short ca be programmed for Active or Tamper respose (see page 64 for details). Ed Of Lie (EOL) Use this wirig cofiguratio whe coectig ormall closed detectio devices to the zoe usig 2-Wires. Zoe wirig should be programmed as Double Pole/EOL (see Zoe Wirig page 53) Whe usig this cofiguratio, o more tha 3 detectors ca be coected to each zoe. Double Pole Use this wirig cofiguratio whe coectig ormall closed or ormall ope detectio devices to the zoe usig 4-Wires. Zoe wirig should be programmed as Double Pole/EOL (see Zoe Wirig page 53) Whe usig this cofiguratio, ol 1 detector ca be coected to each zoe. Alterative resistor values are available see Zoe Wirig o page 53 for more details. Normall Ope Or Normall Closed Circuits This wirig cofiguratio is ormall used for ke switches with a N/O or N/C cotact. Zoe wirig optios are provided for each. Whe usig this cofiguratio, o more tha 10 detectors ca be coected to each zoe. Testig Zoes To test zoes prior to commissioig, use the View Zoe Status optio i Egieers Utilities see page 116. INS

32 Istallatio 60IXD Zoe Expader The 60iXD expader provides the followig facilities: Two id loops each supportig up to 30 biscuits Fused 12V output for powerig detectors Egieer s kepad port for local id diagostics Istallatio Before coectig the 60iXD expader module, isolate ALL power from the cotrol pael (AC mais ad batter), do ot cotiue if there is still power preset o the cotrol pael. 1. Coect the id expader to the cotrol pael, see 60iXD istallatio maual (INS261) for details. 2. Coect the id devices to the expader module, see id Coectios. 3. Reappl power to the cotrol pael ad program the ecessar optios o the pael see 60IXD istallatio maual (INS261) for details. id Coectios Each id biscuit is coected across a two-wire detector loop. Apart from observig the correct polarit, a wirig cofiguratio ca be used, as show i the diagram below: LOOP iXD LOOP As LOOP 1 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Cable Legth Maximum Number of Biscuits 100m m m 7 800m 3 If a differet tpe of cable is used, the distaces should be recalculated. e.g., if 7/0.4mm cable is used, a sigle ru of 200m would support 30 devices o the ed as the resistace of the cable is halved. Whe istallig the id loop it is usuall more practical to ru several cables from the expader module to the differet areas of protectio. This effectivel reduces a distace problems ad makes fault fidig much easier. To reduce the risk of iduced iterferece ad wherever possible, cables should ot be positioed alog side mais power, telephoe or other data trasmissio cables, or ru withi the same ductig or trukig as a other cables. The wirig for the sstem s iteral souders (loudspeakers) should ot be coected i the same multi-core as the id loop. Biscuit Coectios Each id biscuit is idetified b its ow umber 01 to 30 ad cotais its ow iteral sesor that is cotiuousl moitored b the expader module. The diagram below shows the coectios to the biscuit for moitorig both tamper ad alarm cotacts. LOOP + id Biscuit Tamper 01 Biscuit id 08 Yellow White 07 Blue Alarm LOOP - * The 60iXD expader module is supplied with 4 off 10F capacitors i the spares pack. It is recommeded that ou coect a 10F capacitor approximatel at the half wa poit of each id spur. It is especiall importat to do this o id spurs that are less tha 30 metres. Cablig Cosideratios The id loop ca be wired usig stadard 4-core alarm cable, this allows 2 cores to be used for the id biscuit ad 2 cores for supplig 12V power for PIR's etc. Whe the tamper switch is opeed, the id biscuit is take offlie ad a tamper coditio is geerated b the cotrol pael. If the alarm switch is opeed the biscuit's iteral sesor chages state ad the cotrol pael will see this as a active coditio ad will respod as appropriate. The diagram below shows the tpical wirig of a biscuit to a stadard PIR. The umber of biscuits that ca be coected per cable ru is determied b the impedace of the cable used. Stadard 4-core alarm cable (7/0.2mm) has a resistace of approximatel 8 Ohms per 100 metres. The followig table shows the maximum umber of biscuits that ca be coected at the ed of a sigle cable ru usig stadard 4-core alarm cable: id is a registered trade mark of Chloride Safet Sstem Limited. 32 INS176-9

33 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Auxiliar/Fault Coectios The Aux/Fault termials allow the cotrol pael to moitor the tamper & fault loops of exteral devices such as power supplies etc. Istallatio (S) Strb Strobe output, switches to 0V i alarm ad is rated at 500mA. Normall coected to strobe -ve o the souder (where applicable, coect the strobe +ve to +12V). For EN50131 & INCERT istallatios the Bell & Aux Tamper must be wired to a zoe. Au x/ Fault Au x/ Fault Grade 2 Istallatio C otrol Pael Texecom Premier S ouder (A) + 12V - (B) Bell (C ) Tamp (D ) 0V (S ) S trb V (A) Trigger -ve (B ) Tamper (C ) 0V (D) S trobe -ve (S ) 2 Normall C los ed Co ta cts 1 Normall Closed Cotact If the Aux/Fault termials are ot beig used the must be liked out. Speaker Coectios This output ca be used for drivig up to oe 16Ω or two 8Ω loudspeakers as show below: Grade 3 Istallatio F ault Tamper Rela Rela Made I Eglad T S C B T S C B A Cotrol Pael (A) + 12V - (B) Bell (C) Tamp (D) 0V (S) Strb - Aux/ Fault OP? + 12V Bell T mp 0V D S trb MS W 2 1 Test Texecom P remier E lite S ouder C TEXEC OM 2010 = O ptioal B AT T LC ON S AB ON OFF SCB OFF JP1 JP2 JP3 For details o testig Speaker outputs, see page 113. Exteral Souder Coectios The followig termials have bee provided for coectio to a exteral souder: (A)+12V 12V suppl (protected b a 1A fuse F4). Normall coected to +12V o the souder. (B) Bell Souder output, switches to 0V i alarm (SAB) ad is rated at 500mA. Normall coected to Trigger -ve o the souder. This output ca also be programmed for SCB operatio (see page 63 for details). (C) Tamp Negative tamper retur. Normall coected to Tamper Out o the souder. If this termial is ot beig used, it must be coected to 0V. (D) 0V 0V suppl. Normall coected to 0V o the souder. The Aux/Fault rela should be programmed as Fault Grade 3 Istallatio (Usig a Zoe) Texecom Cotrol P remier E lite Pael S ouder INS (A) + 12V - (B) Bell (C) Tamp (D) 0V (S) Strb - Aux/ Fault OP? T A Zoe? = O ptioal Aux/Fault Wire the Souder Tamper Rela to these termials Zoe? Wire the Souder Fault Rela to a Zoe, loopig out the Tamper coectio. The zoe should be programmed as Auxiliar see page 50 ad the wirig tpe set as WD Moitor see page 53 OP? (Optioal) Use a pael output wired to the Test termial ad programmed as WD Test Active see page 78.This will allow activatio of the Test Mode remotel from the Diagostics fuctio i Witex. For details o testig the Bell outputs, see page V A Bell T mp 0V D S trb MS W 2 1 Test Tamper Rela F ault Rela LC ON B AT T ON S AB OFF JP3 SCB JP2 OFF JP1 C TEXEC OM 2010 Made I Eglad

34 Istallatio Pael Outputs The cotrol pael has five programmable outputs, which ca be used to drive auxiliar devices such as LED s, souders or relas etc. (see page 76 for details). The table below shows the electrical characteristics for each output: No Max Curret Tpe 1 500mA Switched -ve 2 500mA Switched -ve 3 ** 500mA Switched +ve 4 ** 500mA Switched +ve 5 ** 3A Rela ** 88/168 & 640 ol Wirig Outputs The diagram below shows some tpical wirig examples: Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Digicom Outputs 1-8 The cotrol pael has eight programmable outputs, which ca be used for coectig to a stad-aloe commuicator (see page 77 for details). The table below shows the electrical characteristics for each output: Termial Max Curret Operatio 1 100mA Switched 0V 2 100mA Switched 0V 3 100mA Switched 0V 4 100mA Switched 0V 5 100mA Switched 0V 6 100mA Switched 0V 7 100mA Switched 0V 8 100mA Switched 0V L/M N/A 12V applied = Lie Fault * R/R N/A 0V applied to reset DC+ N/A +12V Power (ufused) DC- N/A 0V Power * Cotrol Pael Lie Fault Iput (L/M) I accordace with BSIA form 175, the lie fault iput o the cotrol ca detect a sigle or a dual lie fault for use with the ATS Remote Test output tpe Wirig a Stad Aloe Commuicator The diagram below shows a tpical wirig example: S tad Aloe C ommuicator Lie Fa ult Power Chael Iputs Progra mmed as Positive Removed NC C NO 12 V 0V C otrol P ael L / M R / R DC + DC Digic om 5 Outputs For details o testig outputs, see page 113 For details o testig the digicom outputs, see page INS176-9

35 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Istallatio 2-Wire Smoke Detector Pael Output 1 ca be used for coectig up to 10, 12V 2-Wire smoke detectors. C otrol Pael Remote LED (Optioal) + V I + V I + V I -RLED -RLED -RLED E able S moke + V Out + V Out + V Out OV OV 1k EOL OV To eable 2-Wire smoke detectio o pael output 1, a jumper lik must be fitted across the bottom two pis of JP10. The Area Optio 2-Wire Smoke also eeds to be eabled (see page 60). 2-Wire smoke detectors ca ol be coected to pael output 1 Expader Auxiliar Iput This iput ca be used for moitorig a remote power suppl that has a voltage free output for the followig three coditios: AC Mais Fail, Batter Fail, 12V Fail ad Tamper. Aux Iput Whe the Auxiliar Iput is programmed as PSU Moitor the sstem will respod as follows: Tamper 12V Fail Batter Fail A/C Fail Resistace Respose Closed Closed Closed Closed 0R No Faults Closed Closed Closed Ope 2K2 AC Fail Closed Closed Ope Closed 4K7 Batter Fail Closed Closed Ope Ope 6K9 Batter Fail + AC Fail Closed Ope Closed Closed 10K 12V Fail Closed Ope Closed Ope 12K2 AC Fail + 12V Fail Closed Ope Ope Closed 14K7 Batter Fail + 12V Fail Closed Ope Ope Ope 16K9 AC Fail + Batter Fail + 12V fail Ope O/C Lid Tamper INS

36 T R T R Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Plug-o Commuicators The Com300 is a multi format 8-chael digital commuicator/300- baud modem for use with a stadard aalogue telephoe lie. The Com2400 is a multi format 8-chael digital commuicator/2400- baud modem for use with a stadard aalogue telephoe lie i additio, this modem ca also sed Short Message Service (SMS) text messages to a mobile phoe. These Commuicators ca be used to report sstem evets to a Alarm Receivig Cetre usig Fast Format, Cotact ID or SIA Level II or to upload/dowload cotrol pael iformatio usig the Witex UDL software ad a PC. Pluggig o the Commuicator Esure that the board is the correct wa up (see below). Locate the plug ito the commuicator socket o the cotrol pael ad lie up the moutig holes with the pillars i the base. Oce all the holes lie up, press dow getl util the pillars sap ito the holes. Istallatio The cotrol pael ed of the coector should be attached with the red lead o the left most pi of the digi modem coector. Stadard Telephoe Lie Coectios A stadard telephoe lie must be coected to the Com300 or Com2400 commuicator as show below: R1 T1 Mas ter Socket T = 5 or A - White/Blue rig R = 2 or B - B lue/white rig Telephoe cable Tpe 1/0.5mm CW1308 Box Ta m p C om300 T or R Com2400 T1 R1 This termial must be coected to the icomig AC Mais earth suppl To other telephoe extesio sockets Com GSM 48-W Coectio Carefull lift the cotrol pael PCB ad fix the COM uit ito the space provided with the coectio lead attached. C om 1 R1 Audio T1 The red lead should be positioed o the uppermost pi of the COM uit. The Premier Elite Com GSM is a 2G module that ca be coected to a Premier Elite cotrol pael; however fuctioalit differs depedig o the tpe of Premier pael istalled ad the tpe of SIM card that is used. The tables below show which features are available ad the tpe of SIM card required to eable the services. Premier Elite 24/48/88/168 & 640 SIM Tpe Pael Port Tpe Feature Damic GSM Fixed IP IP Module Com IP Report sstem evets (alarms, arm, disarm etc.) via text messagig to mobile telephoes Remotel arm, disarm ad obtai curret status of the alarm sstem via text messagig Upload/Dowload Via GSM Alarm reportig to IP eabled receivers (Motex for example) GPRS Upload/Dowload Via IP GPRS A secodar form of commuicatios should be used as back up where possible. Whe usig Alarm reportig over IP with Motex, SIA, Cotact ID or, Fast Format ma be used, however if usig Texbase SIA is NOT supported. Some receivers ma require a Fixed IP address, please check with our provider. The Com port tpe must be programmed as oe or the other, it is ot possible to use both GSM ad GPRS (IP Ol) fuctioalit at the same time. INS

37 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Istallatio SIM Card Tpes SIM cards are split ito two tpes: Premier Elite ComGSM Laout Damic IP SIM cards the everda kid of SIM card used i mobile phoes. GSM uits that use this kid of SIM card ca access a data o the iteret but caot be cotacted from the iteret. This tpe of SIM card should be used for SMS text messagig & Upload/Dowload via GSM. A data umber will be required to uses Upload/Dowload. Fixed IP SIM cards specialist SIM cards that have a fixed, iteret public IP address which meas that i additio to beig able to access a data o the iteret the ca be cotacted from the iteret. For Premier Elite ComGSM this meas the ca be used for both alarm reportig ad upload/dowload via IP (GPRS) If a data umber is also available, it is possible to use upload/dowload via the data umber (GSM) istead of the IP address. SIM cards ca have two differet phoe umbers: Voice Number: used for voice calls ad SMS Data Number: used for GSM data calls (Upload/Dowload) Either of these facilities ca be eabled/disabled b the operator. Care should be take whe usig Pa as ou go SIM cards, make sure ou have the abilit to Top Up. Pa as You Go SIM cards geerall DO NOT have data umbers, please check with our service provider. SIM cards purchase Texecom DO NOT suppl SIM cards. These will eed to be sourced locall, ad care should be take to source SIM cards i the coutr where the uit is to be used. This will help reduce costs ad avoid excessive data charges. Whe usig GSM as the commuicatio method, Data services will eed to be eabled for upload/dowload, this ma or ma ot be the same Telephoe umber. GPRS SIM card setup I order to use GPRS, the Premier Elite ComGSM must be programmed with certai parameters which are dictated b the SIM card used. This is o differet from mobile phoes (ofte called the GPRS Setup ) except that mobile phoes are ofte supplied precofigured. The cofiguratio cosists of the followig: APN (Access Poit Name) Userame Password These parameters are etered ito the Premier Elite ComGSM usig a Texecom PC program called APNProgrammer (o the Texecom CD supplied with the pael) with the Premier Elite ComGSM powered ad coected to a PC via a Texecom USBCom. To power the Premier Elite ComGSM whilst programmig coect the supplied haress to the cotrol pael com port, ad the other ed to the Egieers Kepad port o the Premier Elite ComGSM. The Texecom USBCom should be coected to the com port o the Premier Elite ComGSM. Use APNProgrammer to upload the required iformatio to the Premier Elite ComGSM. The supplier of the SIM card should provide the iformatio required. Atea coectio Tamper switch Com1 data coectio to Premier cotrol pael Egieer kepad coector (ol used to power the Premier Elite ComGSM whe usig APNProgrammer) Optio switches (see table below) Status LED s (see table below) Audio coector (for future use) Heartbeat LED SIM card socket Optio Switches The optio switches () fuctio as follows: Switch Fuctio Off O 1 Tamper GSM will ot commuicate GSM will commuicate Comms if the uit is i tamper. regardless of the tamper. 2 GPRS server Normal GSM operatio Accepts coectios o port ad allows reportig over GPRS 3 GSM/IP IP mode (19200 baud) V1.65 ad earlier ol GSM mode (9600 baud) V1.65 ad earlier ol 4 N/A For future use leave i OFF positio Status LEDs The three status LED s () idicate the followig: LED Off O Flashig 1 GSM NOT Read GSM Read GSM Commuicatig 2 Pael NOT Read Pael Read Pael Commuicatig 3 No Sigal (less tha 40% Sigal Stregth or - 88dBm) Good (better tha 66% Sigal Stregth or - 77dBm or better) Margial (betwee 40%-66% or -88 ~ - 77dBm) The sigal stregth LED works for both GSM ad GPRS modes; however the dbm readig is ol see o the kepad i GSM mode. INS

38 Istallatio Aerial Sitig ALWAYS do a site surve to fid a area of strog sigal before istallatio. Istallig a Com GSM with a weak sigal is bad istallatio practice. The aerial should be mouted verticall at the poit of strogest sigal. This is usuall the highest poit i the buildig (ofte the loft area). Avoid istallig the aerial directl uder metal roofs or withi metal skied buildigs because this will reduce the sigal stregth ad ma ihibit operatio completel. If this is uavoidable, the strogest sigal will be foud awa from the metal roof or close to large exteral widows or sklights. Avoid istallig the aerial close (2 metres) to cable rus, ductig, structural metalwork, metal pipes, water taks ad electroic equipmet, e.g. photocopiers, fax machies etc. These ca have similar effects to metal roofs. Reliable operatio is ulikel with a low sigal stregth. If the displa shows that the sigal stregth is 40% (-88dBm) or lower, ou should improve the sigal stregth. This ma be achieved b repositioig the aerial. The GPRS aerial lead should ot be cut, therefore repositioig the aerial ma require that the Com GSM is also repositioed. A mobile phoe ma be used to locate the poit of strogest sigal. The sigal stregth idicator is ormall a bar or lie at the side of the displa o the mobile telephoe. The mobile phoe method caot provide iformatio o the availabilit, sigal stregth ad iterferece status of all radio Base Statios i the surroudig area. The sigal stregth readig is idicated o the Com GSM uit b use of LED's ad ca also be read from the kepad i the "Setup Modules" meu of UDL/Digi Optios. Whe ou have idetified the poit of the strogest sigal, make a ote of this poit ad use it whe istallig the Premier Elite Com GSM aerial. Istallatio The Premier Elite Com GSM module should be istalled as close to the cotrol pael as possible, so that the haress lead supplied with the uit is able to plug oto the cotrol pael commuicatio port. The coectio haress caot be exteded. Route the haress lead ito the module housig usig the top left cable etr ad plug the coector oto COM1 () 1. Istall the module i the required locatio usig suitable fixigs. 2. Route the other ed of the haress lead ito the cotrol pael housig. DO NOT CONNECT at this poit. 3. Coect the GSM atea to the atea coector o the module () ad site the atea as high as possible. 4. Ulock the SIM socket b slidig the lockig tab dowwards. Isert the SIM card ito the holder with the chamfered corer to the top left. Push the holder back ito positio ad lock the SIM b slidig the lockig tab upwards. The SIM card must be iserted before coectig the Premier Elite ComGSM module to the cotrol pael, ad must ot be removed util after the power suppl to the Premier Elite ComGSM module has bee deactivated. 5. Set the optio switches as required, see page 37. Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual You should check ad cofirm that the sigal stregth is still the same as recorded durig the site surve. Pael Cofiguratio Text Messagig ad Upload Dowload via GSM GSM Mode (pael port programmed as GSM Module, Damic IP SIM card) 1. Eter Egieers Programmig mode ad select UDL/Digi Optios, the select Com Port Setup. Esure Com Port is programmed as GSM Module. 2. Now select the Digi Optios meu ad make sure that Digi Optio 1 is programmed for Digi is Eabled. 3. Now select Program Digi ad esure the followig optios are programmed for oe of the ARC optios: a) Protocol: SMS Messagig. b) Primar No: The umber of the recipiet s mobile telephoe. c) Secodar No: Secodar mobile telephoe umber (if required). d) Accout No: Leave blak. e) Diallig Attempts: Program as required. f) Report Areas: Program as required. g) Reports: Program as required. h) Cofig.: Program as required. i) Protocol Optios : Program as required. j) UDL Optios : Chage rigs before aswer to 1 if usig GSM Upload/Dowload. 4. All three status LED s should ow be o, if status LED 3 is off or flashig, this idicates a low GSM sigal level. If the sigal level is low, tr movig the atea to improve the receptio. Usig the SMS Cotrol Commads Cotrol commads ca be set to allow remote cotrol ad iterrogatio of the alarm sstem. 1. Select the sed text message optio o our mobile telephoe. 2. Eter the telephoe umber of the Premier Elite ComGSM module. 3. Eter the text commad, see SMS Cotrol Commads. 4. Select sed o our mobile telephoe. Whe usig the SMS Cotrol Commads show i the tables below the followig should be oted:???? = User code, this must proceed all commads. [areas] = Areas 1 to 8 or A to P. If the areas are ot specified the all areas will be selected. [s] = Sed back status report (zoes) = List of zoes, each zoe must separated b a space e.g etc. (outputs) = List of outputs, e.g etc. (message) = A maximum of 32 characters. 6. Now coect the haress lead oto the cotrol pael commuicatio port (COM 1 or 2 ). The module should ow be powered ad the heartbeat LED () should be flashig. 38 INS176-9

39 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Premier 48/88/168/640 & Premier Elite 24/48/88/168/640 SMS Cotrol Commads Operatio Commad Example Arm Sstem???? arm [areas][s] 5678 arm s = arm all areas ad report back status. Part Arm Sstem???? parm (1/2/3)[s] 5678 parm 1 = part arm 1 all areas (o status) Disarm Sstem???? darm [areas][s] 5678 darm abcs = disarm areas abc ad report back status. Reset Sstem???? reset [areas] 5678 reset = reset all areas Omit Zoe(s)???? omit (zoes) 5678 omit = omit zoes 1, 5 ad 12 Uomit Zoe(s)???? uomit (zoes) 5678 uomit 12 = reistate zoe 12 Tur Outputs O???? op o 5678 op o 134 = tur PC outputs 1, 3 (outputs)[s] ad 4 o. Tur Outputs Off???? op off 5678 op off 4s = tur PC output 4 off ad (outputs)[s] report back status. Pulse Outputs O???? op o (outputs) 5678 op o p = pulse PC output 2 o. [p] Pulse Outputs Off???? op off (outputs) 5678 op off p = pulse PC output 2 off. [p] Sed Message???? mess (message) 5678 mess How Are You = Displas How Are You o all kepads. Sstem Status???? status 5678 status = Armed: (1-8 or A - P) Alarm: (1-8 or A - P) Output: (1-8) Mais: (OK or Fault) Batter: (OK or Fault) Phoe Lie: (OK or Fault) Output Status???? status O 5678 status O = Armed: (1-8 or A - P) Alarm: (A - P) Chaels: (1-8) Digi: (1-8) Pael: (1-5) Mais: (OK or Fault) Batter: (OK or Fault) Phoe Lie: (OK or Fault) 5678 status R = Serial: ####### (ol if Radio-Pad fitted) NUA: ###### (ol if Radio-Pad fitted) GSM/Radio-Pad FSS: ### (ol if Radio-Pad fitted)???? status R Status RSS: ### (ol if Radio-Pad fitted) BER: ### (ol if Radio-Pad fitted) CRC: ### (ol if Radio-Pad fitted) GSM-Sigal: ### GSM-BER: ### Istallatio h) For Upload/Dowload via Witex edit the Accout/Pael Details ad fill i the IP address ou have bee give ad Port umber. All three status LED s should ow be o, if status LED 3 is dim, this idicates a low GSM sigal level. If the sigal level is low, tr movig the atea to improve the receptio. What will be set i the Text Message The followig iformatio will be received i the text message: M Home 3 Wester Road 12: /12 Zoe 003 Alarm The Detector i the Louge Area: A... Name programmed ito phoe Up to 16 c harac ters of text (this is the P riter Header) Time ad Date E v e t T p e Zoe/User ame text Area that caused the evet Alarm Reportig & Upload/Dowload via IP IP Mode (pael port programmed as ComIP, fixed IP SIM card) 1. Eter Egieers Programmig mode ad select UDL/Digi Optios, the select Com Port Setup. Esure Com Port is programmed as ComIP. Leave the IP address, port & gatewa blak. 2. Now select the Digi Optios meu ad make sure that Digi Optio 1 is programmed for Digi is Eabled. 3. Now select Program Digi ad esure the followig optios are programmed for oe of the ARC optios: a) Protocol:Program as required. b) Accout No: Program as required c) Diallig Attempts: Program as required. d) Report Areas: Program as required. e) Reports: Program as required. f) Cofig.: Program as required. g) Protocol Optios : Program as required. INS

40 Istallatio AV Module Before coectig the AV Module, isolate ALL power from the cotrol pael (AC mais ad batter), do ot cotiue if there is still power preset o the cotrol pael. To istall the AV Module oto the cotrol pael: Coect oe ed of the patch lead o to the Expasio Port of the AV Module Coect oe other ed of the patch lead o to the Expasio Port of the cotrol pael Programmig the AV Module Program the Expasio Port for AV Module operatio (see page 94 for details) Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Istallatio Geeral The istallatio of the ComIP module requires a basic uderstadig of etworkig ad TCP/IP protocol. If ou are ot familiar with these cocepts, ou ma require assistace from a IT professioal before attemptig to istall the module. The ComIP module is desiged to be fitted iside the cotrol pael ad is powered via the haress coectio. A suitable etwork cable should be fed ito the cotrol pael to allow coectio the module. PCB Laout Refer to the AV Module istallatio guide for full programmig details. ComIP Module The ComIP module allows the Premier Elite cotrol paels to be coected to either a Local Area Network (LAN) or Wide Area Network (WAN). The iteret is cosidered as a WAN. Oce the cotrol pael is coected to a etwork the followig features ca be achieved: Upload/Dowload via Witex UDL Sigal alarms to a Alarm Receivig Cetre High securit pollig b Alarm Receivig Cetre Tpical LAN cofiguratio 5-wa haress coectio to cotrol pael ComIP Status LEDs Network status LED (Left) Network status LED (Right) RJ45 etwork Coectio MAC address Istallatio 1. Select Egieers mode o the cotrol pael the remove the cotrol pael lid. 2. Choose a suitable locatio for the module. Remember to allow eough space to plug i the etwork cable ad coect the haress lead (supplied). 3. Fit the 4 self adhesive feet supplied to the four moutig holes. Remove the self adhesive backig paper ad secure to the base of the cotrol pael. 4. Coect the 5-wa ed of the haress to the 5-wa coector o the module. 5. Coect the other ed oto a cotrol pael commuicatio port. 6. Coect the etwork cable to the RJ45 coectio o the module. The etwork status LED s idicate the followig: Left LED Right LED Meaig Tpical WAN cofiguratio Off Off No Lik Off Solid Amber 100BASE-T Half Duplex Lik Off Blikig Amber 100BASE-T Half Duplex; Activit Off Solid Gree 100BASE-T Full Duplex Lik Off Blikig Gree 100BASE-T Full Duplex; Activit Solid Amber Off 10BASE-T Half Duplex Lik Blikig Amber Off 10BASE-T Half Duplex; Activit Solid Gree Off 10BASE-T Full Duplex Lik Blikig Gree Off 10BASE-T Full Duplex; Activit 40 INS176-9

41 E g K e pa d F3 Kic k S ta rt Ne two r k 1 1A m p F6 F2 F9 C om 2 C o m 1 F5 Ne two r k 2 1A m p Tx 1 R x1 Tx 2 R x2 F1 Au x 1 2v 1A mp F7 L o ad D e f a ul t s E xpa s io J P7 Hear tbeat 100mV = 1A mp V Box T am p J P 1 0 F8 F4 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Commissioig The cotrol pael must be programmed correctl i order for the module to fuctio as expected. The followig sectio covers the items that eed to be cofigured o the cotrol pael i order to make the ComIP module operate correctl. The actual details o how to program the followig items ca be foud i the relevat cotrol pael istallatio maual. PRINT-Com Istallatio The PRINT-Com has two coectors. The 25-wa D-tpe coector coects to a Serial Priter ad the Molex coector plugs oto Com 1 o the cotrol pael. ComIP Address Each TCP/IP ode o a etwork host has a uique IP address. This address provides the iformatio eeded to forward packets o the local etwork ad across multiple etworks if ecessar. IP addresses are specified as x.x.x.x, where each x is a umber from 1 to 254; for example, The ComIP must be assiged a uique IP address to use o a TCP/IP etwork. If the address is left blak or is programmed as the ComIP module will tr to automaticall obtai a IP address from a DHCP server (if oe is ruig o the etwork). ComIP Port The port umber used to idetif the chael for remote iitiated coectios. The default settig is The rage for port settigs is: except for the followig reserved ports: Coectig a Computer The 24, 48, 88, 168 & 640 all support local uploadig ad dowloadig betwee the cotrol pael ad a PC ruig Witex UDL software. Uploadig ad Dowloadig ca be used to program ad iterrogate the cotrol pael. I order for the computer to work correctl, esure that it is set to the followig: UDL Password (see page 91 for details)! US E W IT H TEXE CO M PSU O NL Y Port Numbers Reserved for Reserved (well kow ports) B ell/s trb - 1Am p PC -C om 9999 Telet setup Reserved Reserved Recommeded for raw socket coectios ComIP Gatewa The gatewa address, or router, allows commuicatio to other LAN/WAN segmets. The gatewa address should be the IP address of the router coected to the same LAN segmet as the ComIP. The gatewa address must be withi the local etwork. ComIP Netmask A etmask defies the umber of bits take from the IP address that are assiged for the host sectio. The default mask is (8 bits). USB-Com The USB-Com has two coectors. The USB coector is for coectio to a USB port o a computer ad the Molex coector plugs oto a Com port o the cotrol pael. PC-Com The PC-Com has two coectors. The 9-wa D-tpe coector is for coectio to a serial port o a computer ad the Molex coector plugs oto a Com port o the cotrol pael. I order to upload ad dowload to the cotrol pael locall, a USB/PC-Com lead is required. Coectig a Priter The 24, 48, 88,168 & 640 all support priter facilities. The priter is coected to the Com 1 coector located o the cotrol pael ad ca be used to prit the cotrol pael evet log. I order for the priter to work correctl, esure that it is set to the followig: Baud Rate = 4800 Parit = Noe Start Bits = 1 Stop Bits = 2 Data Bits = 8 DTR = Normal Colums = 40 or 80 (see page 65) I order to coect a priter to the cotrol pael, a PRINT-Com lead is required. PRINT-Com RS232 Data Coect to COM1 DATAC or RS232 priter INS

42 Commissioig ad Troubleshootig Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 4. Commissioig ad Troubleshootig Commissioig Oce ALL coectios have bee made to the cotrol pael ad power is read to be applied, ou should read this sectio before cotiuig. Whe applig power for the first time, the factor default settigs must be loaded. The default settigs esure that the cotrol pael software is reset ad all programmig iformatio is loaded ito memor. For a complete list of factor default settigs, see separate Quick Referece Guide. The factor default settigs are loaded b applig power to the cotrol pael whilst at the same time, holdig dow the Factor Default butto. To default the cotrol pael, proceed as follows: Coect the black batter lead to the egative ( ) termial of the stadb batter ad the red batter lead to the positive (+) termial of the stadb batter Press ad hold the Factor Default butto Press the batter kick-start butto to coect the batter ad esure that the gree heartbeat light illumiates After the heartbeat light has illumiated, let go of the Factor Default butto (the heartbeat light will cotiue to flash whilst the factor default settigs are beig loaded, this ca take up to 30 secods) If the sstem goes ito alarm, eter the default Egieer code, ad the alarm toe will stop To access the Egieer Programmig Meu, eter the default Egieer code The "Cofirm Devices" meu will appear check ad make sure all istalled Kepads ad Expaders are showig, press Yes ad Yes agai to cofirm. Program the sstem as described i sectio 5 (Programmig the Cotrol Pael) Perform a zoe test as described o page 115. Remember that some powered detectors (e.g. PIR s ad combied techolog detectors) take up to 180 secods to warm up ad become operatioal Test the iteral souder, exteral souder ad strobe as described o page 115 Replace the lid ad secure with the lid screw supplied Press followed b YES to leave the programmig meu, the sstem will retur to ormal The displa will be showig that there is a Mais Power Off coditio. Switch o the AC mais suppl to the cotrol pael The ormal baer message (if programmed) will ow be displaed Istallatio is ow complete ad the sstem is read for use. Trouble-Shootig Cotrol Pael No Power to uit (mais ol) Check the mais block fuse ad replace if blow Check for loose wires at the mais block, the trasformer ad the AC termials o the PCB Check the mais block is coected correctl; live to live (brow), eutral to eutral (blue) No Power to uit (batter ol) Do t forget to press the batter kick-start butto Check for loose wires at the BATT termials o the PCB Check that the batter wires are coected correctl; red from BATT+ to the batter positive (+), black from BATT- to the batter egative (-) Heartbeat LED is ot flashig Remove ALL power (AC Mais ad Batter) ad the reappl power agai Network Data LED s are ot flashig Remove ALL power (AC Mais ad Batter) ad remove ALL wires from the etwork termials. The re-appl power agai before referrig to the Network Diagostics table o page 20 Kepads Kepad does ot operate Check that the kepad is wired correctl from the cotrol pael (see page 20 for wirig details) Check the etwork fuses F3 ad F5 ad replace if blow* Use the etwork diagostics (see page 20 for details) *Ol o 48/88/168 Kepad does ot accept codes If the sstem has more tha oe kepad check that each kepad is addressed differetl, see page 22 for details If the kepad is o a log cable ru, check the voltage betwee the + ad termials at the kepad ad esure that it measures o less tha 10.0V Check that ou are usig the correct User codes. The default Egieer code is ad the default Master User code is Check that the User code ou are usig is ot Time Locked, if the User code is time locked the the access code will ol be accepted whe Cotrol Timer 1 is off (see pages 68 ad 110 for details) Kepad zoes do ot operate Each kepad zoe has to be mapped oto the sstem before it ca be used (see page 73 for details) The zoe is ot programmed (see page 48 for details) Kepad emergec kes do ot operate Each kepad ca be cofigured so that the emergec kes PA, FIRE ad MEDICAL ca be eabled or disabled. Check that the kepad has bee programmed correctl (see page 73 for details) 42 INS176-9

43 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Commissioig ad Troubleshootig Expader Expader does ot operate at all Check that the expader is wired correctl from the cotrol pael (see page 20 for wirig details) Check the etwork fuses F3 ad F5 ad replace if blow* *Ol o 48/88/168 Sstem does ot recogise zoes If the expader is o a log cable ru, check the voltage betwee the + ad termials at the expader ad esure that it measures o less tha 10.0V The speaker output does ot work The expader ca be cofigured so that Alarm, Etr, Exit, Chime toes etc. ca be eabled or disabled. Check that the expader has bee programmed correctl (see page 75 for details) The speaker volume o the expader is electroicall adjustable. Check the volume is set to the desired level (see page 75 for details) Zoes Operatio The sstem will ot allow me to arm Check that there are o outstadig problems (see page 44 for details) Check that there are o outstadig alarms that require resettig Check that the User code has bee programmed to allow armig (see page 110 for details) Check that the User code has bee assiged to the correct areas (see page 107 for details) If a Local User code is beig used (see page 110 for details) esure that the kepad beig used is assiged to the correct area (see page 72 for details) The sstem will ot allow me to disarm Check that the User code has bee programmed to allow disarmig (see page 110 for details) Check that the User code has bee assiged to the correct area(s) (see page 107 for details) If a Local User code is beig used (see page 110 for details) esure that the kepad beig used is assiged to the correct area (see page 72 for details) Oe or more zoes show a alarm Check that the zoe is wired correctl (see page 31 for wirig details) Commuicator The Commuicator will ot dial B default the commuicator is disabled, check that the commuicator is eabled (see page 88 for details) Check that the telephoe lie has bee correctl wired to the commuicator (see page 36 for wirig details) Check that the telephoe umbers are programmed correctl (see page 84 for details) Check that the accout umbers are programmed correctl (see page 84 for details) Check that the dial attempts are ot programmed as zero (see page 84 for details) Check that the reportig areas have bee programmed correctl (see page 78 for details) Check that the reportig optios have bee programmed correctl (see page 78 for details) Commuicator dials but does ot commuicate Check that the telephoe umbers are programmed correctl (see page 87 for details) Check that the correct protocol is programmed (see page 87 for details) INS

44 Commissioig ad Troubleshootig Premier Elite 24, 48, 88, 168 & 640 Istallatio Maual Reset ad Service Messages Whe the sstem requires attetio because of a potetial problem, the displa will show oe of three service messages. These messages ca also be accessed at a time, allowig the user to view istaller iformatio. These messages would ormall be programmed with the telephoe umbers of the istaller or the Alarm Receivig Cetre (see page 69 for details). To displa the service messages, proceed as follows: The displa will ormall show the time ad date: Press followed b for the Service message: Press followed b for the Reset message: Press followed b for the Ati-code message: Press to exit from the message, the displa will the retur to ormal. Whe alarm iformatio is beig displaed, pressig the SCROLL ke will slow dow the displa ad also allow maual scrollig through the evets. Fault Warig Toes Whe a fault coditio occurs i.e. mais fail, lie fault etc. the iteral souders will chime ever 30 secods for 3 miutes. The chimig will automaticall stop whe a valid User code is etered, whe is pressed or after 3 miutes (whichever occurs first). The fault idicatio will ol be cleared from the displa whe the fault has bee rectified i.e. power, telephoe lie has bee restored. Fault Messages There are sstem faults waitig to be viewed, eter a valid user code to view the faults. After eterig a code faults will be displaed for 30 secods. If the fault is ot reset withi 30 secods, this message will be displaed agai. The umber of devices coected to the etworks has chaged from the last time a Cofirm Devices was doe. Egieer access is programmed for Egieer code + User code (see page 64 for details). The Egieers code was etered whe the sstem was full armed (access to the programmig meu ca ol be gaied whe the sstem is ot full armed. There are o ATS (Alarm Trasmissio Sstem) paths available. The Stadb Batter has ot bee coected, There is a fault with the cotrol pael stadb batter or it is ot coected. Zoes that have bee placed o test have failed the test. There is a fault with the cotrol pael lid tamper. There is a fault with the bell tamper o the cotrol pael. There is a fault with the auxiliar tamper o the cotrol pael. The bell fuse o the cotrol pael has blow. The Auxiliar fuse o the cotrol pael has blow. There is a fault with the lid tamper of Kepad X,X. Kepad X,X has bee lost off of the sstem. There is a fault with the lid tamper of Expader X,X Expader X,X has bee lost off of the sstem. The voltage at expader X,X is ver low. The expader s Auxiliar iput (that is programmed as bell tamper) is i fault. The expader s Auxiliar iput (that is programmed as aux tamper) is i fault. The service timer has expired idicatig that the sstem requires a service (the sstem ca ormall still be used). The user code is locked out (ormall durig etr). The sstem must be disarmed usig a Prox TAG. To ma ivalid code attempts have caused the kepad to lock out. The kepad will remai like this for 5 miutes. The kepad has bee disabled to prevet uauthorised access. The displa will automaticall clear whe it is re-eabled. Areas are beig armed usig oe of the cotrol timers (eter a valid User code to defer the armig for 30 miutes). The alarm egieer has logged ito the programmig meu ad is workig o site (this message will clear whe the egieer logs off or the sstem is armed). There has bee a AC Mais failure. There is a fault with the ATS (Alarm Trasmissio Sstem). 44 INS176-9

45 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Programmig 5. Programmig the Cotrol Pael Itroductio All egieers should read this sectio carefull so as to familiarise themselves with the programmig of the cotrol pael. Sat 01 Ja 2000 E ter Egieers C ode To access the Programmig meu, eter the factor default Egieer code. 1 Zoe Setup If a mistake is made whilst eterig the Egieer code, simpl re-eter the correct code. 2 Area Programmig WARNING Whe a Egieers code is etered to gai access to the Programmig meu, b default ALL zoes ad tampers are disabled Global Optios Kepad Setup Expader Setup Sstem Outputs A meu optio ca the be selected b pressig oe of the kes show or b usig the ke to search. Oce selected, press YES to access that optio. To leave the selected meu optio ad retur to the mai programmig meu, press. To exit from the Mai Programmig meu but still remai Logged oto the sstem (zoes ad tampers still disabled), press ad the displa will show Alarm Egieer Workig O Site UDL/Digi Optios Setup Users Egieer Utils Log off ENGINEER To log the Egieer off the sstem, press followed b YES ad the sstem will revert to its ormal coditio. P Part Arm Zoes The table below shows the meu optios available: N Do ou wat to EXIT & LOGOFF Ke Meu Optio Page Zoe Setup 48 Area Programmig 54 Global Optios 62 Kepad Setup 72 Expader Setup 74 Sstem Outputs 76 UDL/Digi Optios 83 Setup Users 107 Egieer Utils 112 Alter Part Arms 123 The Armig Meu - The User Meu - Log Off Egieer 47 Exit programmig mode 47 N N R R Do ou wat Armig Meu? Do ou wat User Meu? Log off ENGINEER Alarm Egieer Workig O Site. O ut of P rogramm i g Meu ( Eg ieer S till Lo gg ed O ) INS

46 Programmig the Cotrol Pael Programmig Meu Guide Ke Mai Meu Ke Sub Meu Zoe Setup Lear/Delete Ricochet Device Zoe Tpes Zoe Attributes 1 Zoe Attributes 2 Zoe Areas Zoe Text Zoe Chime Remote Test Zoe Wirig Ricochet Device Mode Area Programmig Timers Armig Modes Area Arm Suites Area Suite Text Suite Arm Modes Area Optios Time Arm Areas Area Text Global Optios Sstem Timers Sstem Cofig. Sstem Optios Moitor Hardware Cotrol Timers Sstem Text Part Arm Text Holida Dates Speaker Toes PC Output Text Custom O/P Text Kepad Setup Areas Zoe Mappig Optios Speaker Volume Souder Optios Expader Setup Areas Locatio Text Auxiliar Iput Speaker Volume Souder Optios Sstem Outputs Pael Outputs Digi Outputs Com? Chaels RedCARE Pis Kepad Outputs Expader Outputs Custom Outputs X-10 Outputs UDL/Digi Optios Reset Digi Test Com? Set Call Waitig Program Digi Digi Optios UDL Optios Area Accouts Radio/SMS Optios Com Port Setup Setup Users Lear/Delete SmartKe Assig SmartKe Routig User Code User Areas User Tpe (ot alwas available) User Optios (ot alwas available) User Cofig. User Time Lock User Text (ot alwas available) Door Cotrol Add TAG Add SmartKe Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Ke Mai Meu Ke Sub Meu Egieer Utils View Evet Log Do Bell Test Do Walk Test View Zoe Status Sstem Tests Cofirm Devices View RKP Status View Exp. Status Set Sstem Time Set Sstem Date Locatio Text Prit Log Data Soak Test Areas Chage Eg. Code Adjust Volumes Default NVM Data View id Data Cofigure Radio Ricochet Diag Part Arms Part Arm 1 Part Arm 2 Part Arm 3 Armig Meu Exit Meu Arm Sstem Part Arm Sstem Silet Armig Omit Zoes Cacel Exit Disarm Areas Use Ati-code View Zoe Status Omit 24Hr Zoes Set Chime Areas View Act. Faults View Act. Couts Sed SMS Text Defer Armig User Meu Exit Meu View Evet Log Chage Code Edit Chime Zoes Sstem Tests Walk Test Eable Egieer Set Sstem Time Set Sstem Date Override Timers Alter Timers Setup Users Alter Part Arms Call Remote PC Alter Hol. Dates Adjust Volumes Prit Evet Log Edit Phoe No s Exit programmig meu (egieer still logged o) Log Off Egieer 46 INS176-9

47 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Programmig Text Text is programmed i a similar wa to mobile phoes. Characters are selected b pressig the correspodig ke the appropriate umber of times (to select a character o the same ke, press to move the cursor alog). The table below shows the kes to use ad the characters that are assiged to them: Ke Character _ 0.,?! - & % / + = $ : ; A B C 2 a b c D E F 3 d e f G H I 4 g h i J K L 5 j k l M N O 6 m o P Q R S 7 p q r s T U V 8 t u V W X Y Z 9 w x z Move Cursor Backspace (delete) Cop Text Paste Text Predictive Text Upper/Lowercase, Predictive text ad Clear Scree The cotrol pael also features Predictive text. This ca be used to make isertig words easier, i.e. whe spellig the word PIR, istead of tpig , all that ou eed to do is tpe 747 ad the word is automaticall selected. This feature ca be tured o ad off as required b pressig the ke ad ca also be automaticall selected ever time text mode is etered (see page 64 for details). Copig ad Pastig Whe programmig a items i.e. Zoes, Timers, Optios etc. pressig CHIME at a poit will Cop the iformatio that has just bee programmed ito memor. To program aother item usig the iformatio i memor, select the item ad press PART to Paste the iformatio. Copig ad Pastig ca ol be performed whilst i the same optio i.e. if a zoe has just bee programmed as Guard 1/Omit/Access/Areas-ABC, ALL of that iformatio ca be copied ito memor so that whe aother zoe is selected, the same iformatio ca the be quickl pasted to the other zoe. The iformatio held i memor after programmig a item ca ol be pasted ito a item of the same tpe ad caot be used oce aother optio is selected i.e. Zoe programmig iformatio caot be pasted ito Timers etc. Log Off Egieer Programmig the Cotrol Pael Wheever the Egieer Programmig meu is exited b pressig twice, the displa will look like this: This message will remai o the displa util the Egieer logs out of the Programmig meu. To log out of Egieer Programmig meu, proceed as follows: Eter a Egieer code, the displa should look like this: Press or, the displa should look like this: Press to retur to ormal, the displa will look somethig like this: The Egieer is ow logged out of the Programmig meu. The Egieer will be automaticall logged out whe the Egieer Logoff Dela Timer Expires (See Page 63) Resettig the Egieers Code (User 00) If the Egieer code (User 00) has bee lost or forgotte, it ca ormall be reset back to the factor default of. However, this ca ol be doe if the NVM has ot bee locked (see page 64 for details). To Reset the Egieer code (User 00): ENSURE THAT THE LID TAMPER IS CLOSED Hold dow the Factor Default butto for 6 secods (with the cotrol pael still powered), after 6 secods, the souders/kepads will bleep to idicate that the Egieer code has bee reset. NO other codes/programmig will be affected, it is just the User 00 Egieer code that will be reset. The Egieer (User 00) code ca ol be reset, if the NVM has ot bee locked (see page 64 for details). Other Thigs to Kow The ke will alwas retur to the previous meu level. This is ofte the ol wa to exit a optio after programmig it. Pressig several times will alwas retur to the top level meu ad the logout scree. The,,, ad kes ofte provide shortcuts or exteded fuctios, refer to idividual programmig optios for details. INS

48 Zoe Setup Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 5.1 Zoe Setup Zoe Setup Zoe 001 Pael 1 Etr/Exit 1? Zoe 004 Pael 4 Etr/Exit 1 R Zoe 004 Attrib1 * * * * * * * * R Zoe 004 Attrib2 * * * * * * * * Eter zoe umber e.g. 004 = Zoe 004 Pre s s NO to edit the zoe tpe Press NO to edit the zoe attributes 1 Use hotkes 1-8 to s e lec t a zoe tpe or us e the S C R OL L ke to s e arc h e.g. 3 = Guard 3 Zoe 004 Pael 4 Zoe 004 Pael 4 Etr/Exit 1 < Guard < Use kes 1-8 to selec t a a ttri bute o r u s e th e S C R OL L ke to s e arc h >* OMITTABLE * * * * * * * ENTRY/EXIT * * * * * *>* 2 U * Press NO to edit the zoe attributes 2 Use kes 1-8 to selec t a a ttri bute o r u s e th e S C R OL L ke to s e arc h Press NO to select/deselect the attribute Press NO to select/deselect the attribute DOUBLE KNOCK AUTO RE-ARM >* * * * * * * * U * * * * *>* * * ENTRY/EXIT 2 * * * * * *>E * AUTO RE-ARM * * * * *>A * * R Press NO to e dit the zoe areas Use kes 1-8 to select a a rea e.g. 2 = B. Use the ARE A ke to toggle betwee a reas A to H ad I to P. For Premier 640 see below Zoe 004 Areas: A... Zoe 004 Areas: > A******* < 2 Zoe 004 Areas: > AB****** < R Zoe 004 R Text: Zoe 004 Chime: Silet R Zoe 004 Test: Remote Test O Press NO to edit the zoe text Us e kes 0-9 to progra m te xt the sa me wa tha t a mobile phoe works e.g. 7, 444, 777 = P IR ^ 7 Press NO to Chage the Chime tpe Press NO to Chage the Test tpe Zoe 004 Chime: Chime ^ 1 Zoe 004 Test: Remote Test Off PIR^ Zoe 001 Areas1 A... Zoe 001 Areas1 ABCDEFGH< ******* A Zoe 001 Areas1 *******>IJKLMNOP A CP / Use the A k e to switch betwee Area G roups 1,2,3 & 4 U se the C hime & Part kes to sc roll betwe e Are a G roups 1, 2, 3 & 4 Use the Area ke to select either A-H or I-P a rea s. Us e the ume ric buttos 1-8 to toggle the required areas o or off 48 INS176-9

49 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Zoe Setup Ricochet Devices MT2 Optio Switches I this mode ol optio switch 3 should be o. Itroductio The firmware upgrade ow requires that Ricochet devices are leared through the Zoe Setup Meu, ad Premier Elite SmartKe are leared through the User Setup meu, the "Cofigure Radio" meu i Egieer's Utilities is ow redudat ad should ot be used o MT2 sstems. Learig Devices To lear a device to a Zoe select the Zoe from the Zoe Setup Meu, Zoes that are capable of havig a Ricochet device leart to them will be displaed as follows:- Fig 1 Fig 1idicates the pre-assiged zoe umber, the expader beig used ad the device slot o the expader. Oce a device has bee leart the displa will be as Fig 2:- Fig 2 If ou are usure if a zoe alread has a device leared to it, ou ca go to the meu as i Fig 1, press ad the if a device is alread leart the displa will look like Fig 2, if ot the it will look like Fig 3 Fig 3 Deletig Devices To delete devices from the expader is the same as learig them; choose the zoe ou wish to delete, ad follow the procedure to lear the device, whe the scree shows Learig press. Learig Devices Yes to Select:- Zoe Setup Zoe 001 Pael01 Not Used? Zoe 009 XP01,01 Not Used * R Zoe 009 Lear: Learig... 20s R Zoe 009 Lear: PIR XP-W01,01 Zoe 009 XP01,01 Not Used Eter zoe umber e.g 009 = Zoe 009 * Zoe 009 Attrib1 * * * * * * * * * Zoe 009 Attrib2 * * * * * A * * * Zoe 009 Areas: A... * Zoe 009 Text: * Zoe 009 Chime: Silet * Zoe 009 Test: Remote Test Off * Zoe 009 Mode: Hbrid * Zoe 009 Group: 00 * Zoe 009 Lear: PIR XP-W01,01 R U Zoe 010 Lear: Free XP-W01,02 R Use the scroll ke to select the ext zoe to lear a device too * Please refer to previous page for details o programmig these optios INS

50 Zoe Setup Zoe Tpes Each zoe must be programmed before it is recogised b the sstem. Zoe umbers are etered as a three digit umber i.e. Zoe 1 would be etered as 001. Each zoe cosists of a zoe tpe, attributes, areas ad zoe text. Whe programmig zoes, first select a zoe tpe the select a required attributes, assig the zoe to a area ad the program a required zoe text. Zoe Tpe + Zoe Attributes + Zoe Areas + Zoe Text = Zoe Programmed. The followig zoe tpes are available: 0 - Not used A zoe that is ot moitored b the sstem, uused zoes should be programmed as Not Used or liked out. 1 - Etr/Exit 1 Normall used for the mai etr/exit door i.e. Frot Door. The zoe ca be activated durig the exit mode without causig a Fault. Oce the sstem/area is armed, activatio of the zoe will start the Etr 1 Dela timer for the selected area. 2 - Etr/Exit 2 Normall used for aother etr/exit door that requires a differet etr dela i.e. Back Door, Garage Door etc. The zoe ca be activated durig the exit mode without causig a Fault. Oce the sstem/area is armed, activatio of the zoe will start the Etr 2 Dela timer for the selected area. If a Etr/Exit zoe remais active at the ed of the etr time, it will automaticall be omitted util the sstem has bee uset ad re-set. If a Etr/Exit zoe tpe is locked out, Guard Access zoes i the same area as the omitted Etr/Exit zoe will automaticall become Etr/Exit 1 zoes to allow access ito the premises without causig a alarm. If a Etr/Exit 1 or 2 zoe tpe is assiged the Etr/Exit 2 attribute (see page 51), whe a zoe with the Guard attribute activates ad causes a alarm (whe the area is full armed), the zoe will become a Guard zoe for the duratio of the Abort timer. 3 - Guard Normall used for detectio devices such as PIR s, Door Cotacts etc. This zoe tpe will cause a Itruder alarm if it is activated whe the sstem/area is armed. This zoe tpe will also activate a output programmed as Guard Alarm. 4 - Guard Access Normall used for detectio devices alog the etr/exit route. This zoe tpe will allow the user to walk past the detector without causig a Fault durig the exit mode or a Itruder alarm durig the etr mode, however, the zoe will cause a immediate Itruder alarm if activated at a other time. This zoe tpe will also start the etr mode whe the sstem/area is part armed ad activate a output programmed as Guard Access Alarm. 5-24Hr Audible This zoe tpe will cause a iteral alarm if it is activated whe the sstem/area is disarmed ad will cause a Itruder alarm whe the sstem/area is armed. The pael will also report a 24-Hour alarm to the Alarm Receivig Cetre whe usig Cotact ID reportig. 6-24Hr Silet This zoe tpe will cause a silet alarm if it is activated whe the sstem/area is disarmed ad will cause a Itruder alarm whe the sstem/area is armed. The pael will also report a 24-Hour Alarm to the Alarm Receivig Cetre whe usig Cotact ID reportig. 7 - PA Audible Normall used for moitorig Paic or hold-up alarms. This zoe tpe will cause a Paic alarm if it is activated whe the sstem/area is armed or disarmed. 8 - PA Silet Normall used for moitorig Paic or hold-up alarms. This zoe tpe will cause a silet Paic alarm if it is activated whe the sstem/area is armed or disarmed. Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 9 - Fire Normall used for moitorig smoke detectors. This zoe tpe will cause a Fire alarm with distictive fire toe if it is activated whe the sstem/area is armed or disarmed. I additio, the bell output will pulse Medical This zoe tpe will cause a Silet alarm if it is activated whe the sstem/area is armed or disarmed. The pael will also report a Medical alarm to the Alarm Receivig Cetre whe usig Cotact ID reportig Hr Gas This zoe tpe will cause a Audible alarm if it is activated whe the sstem/area is armed or disarmed. The pael will also report a 24- Hour Gas alarm to the Alarm Receivig Cetre whe usig Cotact ID reportig Auxiliar This zoe tpe will cause a Silet alarm if it is activated whe the sstem/area is armed or disarmed. The pael will also report a Auxiliar alarm to the Alarm Receivig Cetre whe usig Cotact ID reportig Tamper This zoe tpe will cause a Iteral alarm if it is activated whe the sstem/area is disarmed ad will cause a Itruder alarm whe the sstem/area is armed Exit Termiator This zoe tpe is used to fialise the armig procedure whe armig the sstem/area (see page 55 for details) Momet Ke This zoe tpe ca be used to arm ad disarm oe or more areas. Whe the zoe is activated ad the secured the areas assiged to the zoe will arm. Whe the zoe is subsequetl activated ad the secured the sstem will disarm the areas assiged to the zoe. Tamper faults will ot arm or disarm athig, but will cause a Tamper alarm Latch Ke This zoe tpe ca be used to arm ad disarm oe or more areas. Whe the zoe is activated, the areas assiged to the zoe will arm. Whe the zoe is secured, areas assiged to the zoe will disarm. Tamper faults will ot arm or disarm athig, but will cause a Tamper alarm Securit This zoe tpe ca be used to Lockout kepads. Whe the zoe is activated, kepads assiged to the same area will ot accept a ke presses. Whe the zoe is secured, all kepads respod as ormal Omit Ke This zoe tpe will isolate a zoe assiged to the same area as log as it has the Omit attribute Custom This zoe tpe ca be programmed to operate as required usig its ow set of attributes (see page 52 for details) Cof PA audible This zoe tpe is for use with multi actio PA buttos, or where a cofirmed PA is required, ad will activate local souders Cof PA silet This zoe tpe is for use with multi actio PA buttos, or where a cofirmed PA is required, ad will ot activate local souders. 50 INS176-9

51 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Zoe Attributes 1 Attributes ca be assiged to a zoe to alter its operatio i.e. a Guard zoe with the Access attribute will allow the user to walk past the detector without causig a Fault durig the exit mode or a Itruder alarm durig the etr mode. Select attributes b pressig kes 1 to 8 (a letter o the displa meas the attribute is selected, a Dot o the displa meas the attribute is ot selected). The followig attributes are available: O - OMITTABLE Zoes with this attribute ca be mauall omitted. Zoes without this attribute caot be mauall omitted. F - FORCE OMIT Zoes with this attribute will be omitted if the are ot secure at the ed of the exit mode. Zoes without this attribute will cause a Arm Fail if the are ot secure at the ed of the exit mode. 1 - PART 1 OMIT Zoes with this attribute will be omitted whe Part Arm 1 is selected. Zoes without this attribute will respod as ormal. 2 - PART 2 OMIT Zoes with this attribute will be omitted whe Part Arm 2 is selected. Zoes without this attribute will respod as ormal. 3 - PART 3 OMIT Zoes with this attribute will be omitted whe Part Arm 3 is selected. Zoes without this attribute will respod as ormal. A - ACCESS Zoes with this attribute will ot cause a Fault durig the exit mode or a Itruder alarm durig the etr mode. However, if the zoe is activated at a other time a Itruder alarm will occur. Zoes without this attribute will respod as ormal. E - ENTRY/EXIT 2 Zoes with this attribute will start the Etr Dela 2 timer for the selected area whe the area is part armed. Etr/Exit 1 or 2 zoes with this attribute will become a Guard zoe for the duratio of the Abort timer if a zoe with the Guard attribute activates ad cause a alarm (whe the area is full armed). Zoes without this attribute will respod as ormal. G - GUARD Zoes with this attribute will cause a Itruder alarm whe the area is part armed (this would ormall be used o Etr/Exit 1 or 2 zoe tpes). Whe the area is full armed, activatio of a zoe with this attribute will cause a Etr/Exit 1 or 2 zoe with the Etr/Exit 2 attribute to become a Guard zoe for the duratio of the Forced Etr timer. Zoes without this attribute will respod as ormal. Zoe Attributes 2 Zoe Setup Select attributes b pressig kes 1 to 8 (a letter o the displa meas the attribute is selected, a Dot o the displa meas the attribute is ot selected). The followig attributes are available: D - DOUBLE KNOCK Zoes with this attribute will ol cause a alarm if it is activated twice withi the Double Kock time widow or for the duratio of the time widow. Zoes without this attribute will respod as ormal. B - BEAM PAIR Zoes with this attribute will ol cause a alarm if two zoes (assiged to the same area) with this attribute are activated withi the Beam Pair time widow. Zoes without this attribute will respod as ormal. T - ON TEST Zoes with this attribute will be put o soak test for the duratio of the soak test timer (see page 62), whe the area soak test optio is selected (see page 120) Zoes without this attribute will respod as ormal. A - ACTIVITY Zoes with this attribute will cause a activit fault to be displaed at the time of armig if the have ot bee activated durig the Activit Dela period. If Cofig. optio 14 (see page 64 for details) has bee set to Activit Fault Bar the sstem/area caot be armed util the zoe has bee activated (forced walk test). Zoes without this attribute will respod as ormal. R - RESET Zoes with this attribute will ot be moitored durig the Detector Reset period i.e. whe the exit mode is started ad power is removed from certai detectors (to reset them) the Fault o the zoe is igored. Zoes without this attribute will be moitored as ormal. A - AUTO RE-ARM Zoes with this attribute will ol re-arm at the ed of the bell duratio providig that the Re-arm limit has ot bee reached (see page 67 for details). Oce this limit has bee reached, the zoe will lock out ad ot cause a further Itruder alarms. Zoes without this attribute will alwas re-arm at the ed of the bell duratio. Q - QUICK RESPONSE. The respose time of the zoes with this attribute is govered b the Zoe Loop respose Timer (see page 62 for details). The respose time of a zoe without this attribute is fixed at 250mS. E ENGINEER ALARM Zoes with this attribute will cause a Itruder alarm whe activated if the egieer arms the sstem/area. Zoes without this attribute will ot cause a Itruder alarm whe activated if the egieer arms the sstem/area. INS

52 Zoe Setup Attributes for Momet or Latch Kes Select attributes b pressig kes 1 to 8 (a letter o the displa meas the attribute is selected, a Dot o the displa meas the attribute is ot selected). The followig attributes are ol available for Momet Ke or Latch Ke zoe tpes. I - INSTANT ARM Whe usig a ke switch, the area will arm istatl. P - PART ARMING Whe usig a ke switch, the area will Part arm. F FULL ARM DISABLE Whe usig a ke switch to Full arm a area, the ke switch is disabled oce the area is armed. D - DISARM ONLY The ke switch caot be used for Armig (it ca ol be used for Disarmig ). F - SILENTARMING Whe armig usig a ke switch, the selected areas will arm siletl. T - TIME ARM DISABLE Activatio of the ke switch will override the Time Armig feature o the cotrol pael ad prevet it from operatig util the zoe is reistated. K - KEY TUBE A ke switch zoe tpe with this attribute will log whe the zoe is activated ad also whe the zoe is restored. Attributes for Custom Zoes Select attributes b pressig kes 1 to 8 (a letter o the displa meas the attribute is selected, a Dot o the displa meas the attribute is ot selected). The followig attributes are ol available for Custom zoe tpes. I - INTERNAL Activatio of this zoe (whe armed) will cause the iteral souders to activate. B - BELL/STROBE Activatio of this zoe (whe armed) will cause the exteral souder/strobe to activate. M - MONITOR 24Hr The zoe is armed at all times. C - ENABLE COMS Activatio of this zoe (whe armed) will cause the area Alarm output to activate. A Custom zoe with this attribute will activate both the iteral ad exteral souders eve if the are ot eabled above. W - WARNING REQ. If the zoe remais Active for the duratio of the Warig Dela timer (see page 63), a warig toe will occur ever 30 secods for 3 miutes (or util a code is etered or is pressed). If MONITOR 24Hr is eabled, a iteral alarm will occur after the Warig Dela. Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Zoe Areas 24/48/88/168 The 24 ca be divided ito two separate areas of protectio, the 48 ca be divided ito four separate areas of protectio, the 88 ca be divided ito eight separate areas of protectio, ad the 168 ca be divided ito sixtee separate areas of protectio. This allows differet parts of a buildig to be armed ad disarmed idepedetl from each other. B default all zoes are assiged to area A, but if required, a zoe ca be assiged to a umber of areas. If a zoe is assiged to more tha oe area, it will ol be recogised b the sstem whe all areas it is assiged to, are armed. Zoe Areas 640 The 640 ca be divided ito sixt four separate areas of protectio. This allows differet parts of a buildig to be armed ad disarmed idepedetl from each other. B default all zoes are assiged to area A, but if required, a zoe ca be assiged to a umber of areas. If a zoe is assiged to more tha oe area, it will ol be recogised b the sstem whe all areas it is assiged to, are armed. Programmig of Zoe Areas for the 640 has additioal requiremets. Areas o the 640 are divided ito 4 sets of 16 areas idetified b the table below. Area Groups Area's 1 A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P, 2 A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P, 3 A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P, 4 A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P, Zoe 001 Areas1 A... Zoe 001 Areas1 ABCDEFGH< ******* A Zoe 001 Areas1 *******>IJKLMNOP Zoe Text A CP / Use the A ke to switch betwee Area G roups 1,2,3 & 4 Use the C hime & Part kes to s croll betwe e Area G roups 1,2,3 & 4 Use the Area k e to select either A-H or I-P a rea s. Us e the ume ric buttos 1-8 to toggle the required areas o or off Each zoe ca have up to 32 characters of descriptive text assiged to it. Text is programmed i a similar wa to mobile phoes. Select characters b pressig the correspodig ke the appropriate umber of times (to select a character o the same ke, press to move the cursor alog). For a more iformatio, see page 47. The cotrol pael also features Predictive text. This ca be used to make isertig words easier, i.e. whe spellig the word PIR, istead of tpig , all that ou eed to do is tpe 747 ad the word is automaticall selected. This feature ca be tured off if required b pressig the ke ad ca also be automaticall selected ever time text mode is etered. Zoe Chime Each zoe ca be programmed to chime the iteral souders usig oe of the available chime toes whe activated. 52 INS176-9

53 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Remote Test Eable A zoe with this attribute will be tested whe the remote test fuctio is iitiated from Witex. A detector o a zoe with the remote test attribute will be expected to go ito alarm durig the remote test, if it does ot go ito alarm, the detector will be reported as fault. This facilit is ol to be used i cojuctio with sstem output tpe 47 Detector Test see page 78. Zoe Wirig Zoe wirig coectios are show o page 31 the followig programmig optios are available. 0 - Normall Closed For use o ormall closed devices without tamper protectio. Normall used for keswitches. See Normall Closed wirig diagram o page Normall Ope For use o ormall closed devices without tamper protectio. Normall used for keswitches. See Normall Ope wirig diagram o page Double Pole/EOL Default zoe wirig cofiguratio. 3 - Triple EOL Stadard Texecom TEOL, use this wirig tpe for all Texecom ati maskig detectors. 4-1K/1K/(3K) Alterative TEOL cofiguratio with 1K alarm resistor, 3K fault resistor ad 1K EOL resistor 5-4K7/6k8/(12K) Alterative TEOL cofiguratio with 6K8 alarm resistor, 12K fault resistor ad 4K7 EOL resistor. 6-2K2/4K7/(6k8) Alterative TEOL cofiguratio with 4K7 alarm resistor, 6K8 fault resistor ad 2K2 EOL resistor 7-4K7/4k7 Alterative EOL cofiguratio with 4K7 alarm resistor ad 4K7 EOL resistor. 8 - WD Moitor Specialised wirig cofiguratio for moitorig warig devices with fault reportig capabilit. Ol use this wirig tpe o zoes tpes programmed as Auxiliar. Normall wired as a Normall Closed circuit. Ricochet Device Mode Ricochet Device Mode determies how wireless devices will operate o the sstem. This optio ol appears i the meu after a device has bee leared to the zoe, ad replaces the wirig tpe optios. Exp O/P 1-2* Exp O/P 3-4* Exp O/P 5-6* Exp O/P 7-8* Exp O/P 1-3* Exp O/P 4-6* * For Future Use Zoe Groups Zoe Setup Zoe groups allow multiple zoes to be assiged to a Zoe Group Output. Oce assiged triggerig a of the zoes assiged to the group will trigger the output. The default optio for each Zoe is 0 ad meas the Zoe is ot assiged to a group. Please see page 82 for the programmig optios for the Zoe Group Output Tpe. Pael DD 243 Output Groups To compl with DD 243, durig the ormal etr dela, the cotrol pael must prevet a Cofirmed Itruder Alarm from beig reported to the Alarm Receivig Cetre. WARNING Owig to the abilit to disable ALL of the cofirmatio facilities, the customer should be advised i writig b the alarm compa that ALL meas of alarm cofirmatio are disabled whe the iitial etr door is opeed. The alarm compa should the obtai writte acceptace from the customer of the disablig of the meas of alarm cofirmatio. Alwas Awake o This mode should ol be used o devices which are required to sigal at all times ad is the default settig for the Impaq Cotact-W ad Impaq Plus-W. Hbrid o Hbrid mode is used to cotrol the reportig fuctios for devices. Whe i the mode devices are asleep whe the sstem is set, ad are woke up b the cotrol pael at the poit of armig. Whe the sstem is disarmed the devices will be put back to sleep. This mode of operatio is the default mode for XT-W, QD- W & DT-W. Auto o Whe i Auto Mode, devices poll at 15 miute itervals. Followig activatio, devices will ot trasmit the same activatio agai for a period of 3 miutes. INS

54 Area Programmig Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 5.2 Area Programmig Timers Area Programmig Area Programmig Timers A> Exit Dela 030 Secod(s) U B> Exit Dela 030 Secod(s) R B> Etr 1 Dela 020 Secod(s)? B> Etr 1 Dela >025 Secod(s) 1A> Exit Dela 030 Secod(s) Use the S CROLL ke to select a area F or 640 see below Pres s YE S to move to the required timer group or press RE SET to move backwards e.g. YES E ter a e w timer value e.g. 025 = 25 Secods Use the SCR OLL ke to select areas betwee 1A - 4P These groups of Area timers cotrol timig ad dela fuctios for areas A - B (24) A - D (48), A - H (88) ad A - P (168) & groups 1-4 Area A-P (640) Each timer ca be programmed for a value betwee 000 ad 999. The area bell timers i optios 5, 6 ad 8 below are ol active whe sstem cofig optio 5 is switched to Area Bell Time. Timers listed are for Areas A to B (A to D) (A to H) (A to P) (1,2,3,4, A-P) depedig o the pael beig used. 1 - Exit Dela Whe the area exit mode is programmed as Timed this timer cotrols the dela betwee the user iitiatig the exit mode for the selected area ad the area actuall. 2 - Etr 1 Dela If the area is armed ad a Etr/Exit 1 zoe is activated, this timer will start ad the etr toe will be heard. If the area is ot disarmed before this timer expires, the 2 d Etr Dela timer will start. 3 - Etr 2 Dela If the area is armed ad a Etr/Exit 2 zoe is activated, this timer will start ad the etr toe will be heard. If the area is ot disarmed before this timer expires, the 2 d Etr Dela timer will start. 4-2 d Etr Dl Whe the area Etr Dela 1 or 2 timer expires, this timer will start ad a Iteral alarm will occur. If the area is still ot disarmed before this timer expires, a Itruder alarm will the occur. 5 - Bell Dela This timer cotrols the dela betwee a Itruder alarm occurrig i the selected area ad the Bell/Strobe output activatig. 6 - Bell Duratio This timer cotrols the duratio of the Bell output after a Itruder alarm has occurred i the selected area ad a programmed Bell Dela has expired. 7 - Coms Dela. This timer cotrols the dela betwee a Itruder alarm occurrig i the selected area ad the commuicator reportig to the Alarm Receivig Cetre. 8 - Part Bell Dl. for Areas A to D (A to H) (A to P) Whe the selected area is Part Armed this timer cotrols the dela betwee a Itruder alarm occurrig i the selected area ad the Bell/Strobe output activatig, the iteral souders will also soud durig this time as a warig. 9 Cofirm PA Timer, for Areas A to B (A to D) (A to H) (A to P) (1A to 4P) Whe a Paic Alarm is raised i a area a cofirm PA timer is started for that specific area. If a secod PA alarm (icludig tamper from a other device i the same area) is raised while the PA timer is active a Cofirmed PA Alarm is raised. 54 INS176-9

55 P Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Armig Modes Area Arm Suites 24/48/88/168 Area Programmig Area Programmig Area Programmig Timers 1 Area Programmig Armig Modes Area A Arm b: Timed exit U Area B Arm b: Timed exit 1 Area B Arm b: > Etr/Exit Use the SCR OLL ke to s ele ct a area Use kes 1-5 to select a armig mode e.g. 1 = Etr/Exit The wa that a area arms ca be cofigured for a of the followig optios: 1 - Etr/Exit The area will arm after the Etr/Exit door has bee closed ad the Exit Settle timer has expired. 2 - Exit Term. The area will arm after the Etr/Exit door has bee closed, the Exit Termiator butto has bee pressed ad the Exit Settle timer has expired. 3 - Timed Exit The area will arm after the programmed Exit Time has expired. If a Exit Termiator zoe is activated at a poit durig the exit mode, a remaiig exit time is cacelled ad the area will arm immediatel. 4 - Istat The area will arm istatl. 5 - Deferred The area will arm after the programmed Exit Time has expired. However, if a zoes ot o the exit route are activated durig the exit mode, the Exit Time is restarted. Area Programmig Area Programmig Timers 2 Area Programmig Area Arm Suites Area Arm Suite 1 A... 4 Area Arm Suite 4...D... Area Arm Suite 4 > ***D**** < 3 Area Arm Suite 4 > **CD**** < Us e kes 1-8 to se le ct a Area Arm S uite or us e the SCROLL ke to search e.g. 4 Pre s s NO to edit the Pa rt Arm S uite Us e kes 1-8 to se le ct a a rea e.g. 3 = C. Use the AREA ke to toggle betwee area s A to H a d I to P The 24 has 2 Area Arm Suites the 48 has 4 Area Arm Suites the 88 has 8 Area Arm Suites the 168 has 16 Area Arm Suites. A umber of areas ca be assiged to each suite. Areas assiged to a Area Arm Suite will be armed whe the suite is selected, makig it easier for the user to select multiple areas if required. Example Area Arm Suites could be useful i a domestic situatio where the user wats to arm areas A ad B at ight but does ot wat to select each area idividuall. Areas A ad B would be assiged to Area Arm Suite 1 Whe the user wats to arm the sstem at ight, Area Arm Suite 1 would be selected Areas A ad B are automaticall selected for armig Descriptive text ma also be assiged to the Area Arm Suite (see page 56 for details). Area Arm Suite Cotroller The suites ca be assiged to kepads so that differet combiatios of areas ca be armed or disarmed depedig o which kepad is used (see page 73 for details) ad operates as follows: Kepad 1 = Area Arm Suite 1, Kepad 2 = Area Arm Suite 2, Kepad 3 = Area Arm Suite 3 etc. Whe a User code is etered at a kepad, oe of the Area Arm Suites is selected (depedig o which kepad was used) ad the areas cotaied withi that suite arm usig the armig mode for that suite, the kepad souder will also follow the areas defied b the suite. INS

56 Area Programmig Area Arm Suites 640 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Area Suite Text Area Programmig Area Programmig Timers 2 Area Programmig Area Arm Suites Area Programmig Area Programmig Timers 3 Area Programmig Area Suite Text Suite01 ArmArea1... A Use the Area ke to select the A rm Area 1-4 SUITE 1 Area Arm Suite 1 4 Use kes 1-8 to selec t a Area Arm S uite or us e the SCROLL ke to search e.g. 4 Suite01 ArmArea4... Press NO to edit the Part Arm S uite SUITE 4 Area Arm Suite 4 P res s NO to edit th e Area Arm S u ite te xt Suite01 ArmArea4 ABCDEFGH<...? Suite01 ArmArea4 ABCDEFG>... Use the C hime & Pa rt kes to s elect the Arm Area. Use the Area ke to toggle betwee Areas A to H ad I to P. Us e the 1-8 kes to toggle the Areas o & off SUITE 1 ^Edit Text >ABC? Bedtime Settig Edit Text >A^C Us e kes 0-9 to progra m te xt the sa me wa tha t a mobile phoe works The 640 has 4 groups of 16 Arm suites. A umber of areas ca be assiged to each suite. Areas assiged to a Area Arm Suite will be armed whe the suite is selected, makig it easier for the user to select multiple areas if required. Example Area Arm Suites could be useful i a domestic situatio where the user wats to arm areas A ad B at ight but does ot wat to select each area idividuall. Areas A ad B would be assiged to Area Arm Suite 1 Whe the user wats to arm the sstem at ight, Area Arm Suite 1 would be selected Areas A ad B are automaticall selected for armig Descriptive text ma also be assiged to the Area Arm Suite (see page 56 for details). Area Arm Suite Cotroller The suites ca be assiged to kepads so that differet combiatios of areas ca be armed or disarmed depedig o which kepad is used (see page 73 for details) ad operates as follows: Kepad 1 = Area Arm Suite 1, Kepad 2 = Area Arm Suite 2, Kepad 3 = Area Arm Suite 3 etc. Whe a User code is etered at a kepad, oe of the Area Arm Suites is selected (depedig o which kepad was used) ad the areas cotaied withi that suite arm usig the armig mode for that suite, the kepad souder will also follow the areas defied b the suite. Text ma be assiged to the Area Arm Suites to allow the user to select the suites b descriptio istead of umber. Up to 16 characters of text ca be programmed for each suite. Example Text descriptios for the Area Arm Suites could be useful where more tha oe suite has bee defied. The user wishes to arm areas A ad B at ight but is ot too sure which suite to select. Areas A ad B would be assiged to Area Arm Suite 1 (see page 55 for details) Whe the user wats to arm the sstem at ight, Area Arm Suite 1 would be selected Text will be displaed to cofirm that the selected suite is correct i.e. Bedtime Settig Areas A ad B are automaticall selected for armed Text is programmed i a similar wa to mobile phoes. Select characters b pressig the correspodig ke the appropriate umber of times (to select a character o the same ke, press to move the cursor alog). 56 INS176-9

57 P Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Area Programmig Suite Arm Modes Area Optios 24/48/88/168 Area Programmig Area Programmig Timers 4 Area Programmig Suite Arm Modes Area Programmig Area Programmig Timers 5 Area Programmig Area Optios Suite 1 Arm b: Timed exit U Use the SCR OLL ke to s ele ct a suite Auto Part Arm A... U Use the S CROLL ke to select a area optio Suite 2 Arm b: Timed exit 1 Use kes 1-5 to select a armig mode e.g. 1 = Etr/Exit Remote Arm A... Press NO to cha ge the a rea optio Suite 2 Arm b: > Etr/Exit The wa that a Area Arm Suite arms whe selected, ca be cofigured for a of the followig optios: 1 - Etr/Exit The suite will arm after the Etr/Exit door has bee closed ad the Exit Settle timer has expired. 2 - Exit Term. The suite will arm after the Etr/Exit door has bee closed, the Exit Termiator butto has bee pressed ad the Exit Settle timer has expired. 3 - Timed Exit (Default for All Areas) The suite will arm after the programmed Exit Time has expired. If a Exit Termiator zoe is activated at a poit durig the exit mode, a remaiig exit time is cacelled ad the area will arm immediatel. 4 - Istat The suite will arm istatl. 5 - Deferred The suite will arm after the programmed Exit Time has expired. However, if a zoes ot o the exit route are activated durig the exit mode, the Exit Time is restarted. Remote Arm > A******* < 4 Remote Arm > A**D**** < Area Optios 640 Area Programmig Area Programmig Timers 5 Area Programmig Area Optios Auto Part Arm 1 A...? Auto Part Arm 1 A... Auto Part Arm 1 A...<... 4 Auto Part Arm 1 ABC... Use kes 1-8 to s ele ct a a rea e.g. 4 = D Us e the S c roll Ke to s ele ct the optio. Use the Area ke to select th e A rm Ar ea 1-4 Pre s s NO to edit the optio Use the C hime & Part kes to select the Arm Area. Us e the Area ke to toggle betwee Areas A to H ad I to P. Us e the 1-8 kes to toggle the Areas o & off INS

58 Area Programmig Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual These optios cotrol how various features affect each area. A umber of areas ca be assiged to each optio. 1 - Auto Part Arm Areas assiged to Auto Part Arm will full arm if a Etr/Exit zoe is activated durig the exit mode ad will Part Arm 1 if a Etr/Exit zoe is ot activated durig the exit mode. Areas ot assiged to Auto Part will alwas full arm. 2 - Part Arm Istat Areas assiged to Part Arm Istat will arm istatl whe part armig. Areas ot assiged to Part Arm Istat will use the area exit timer whe part armig. 3 - Part Arm Silet Areas assiged to Part Arm Silet will ever geerate Exit toes whe part armig. Areas ot assiged to Part Arm Silet will alwas geerate Exit toes whe part armig. 4 - Remote Arm Areas assiged to Remote Arm ca be armed remotel usig the Witex UDL software ad a PC. Areas ot assiged caot be armed remotel. 5 - Remote Disarm Areas assiged to Remote Disarm ca be disarmed remotel usig the Witex UDL software ad a PC. Areas ot assiged to Remote Armig caot be disarmed remotel. 6 - Pael Tamper Areas assiged to Pael Tamper will cause a Tamper alarm whe the cotrol pael cover is removed. Areas ot assiged to Pael Tamper will ever cause a Tamper alarm whe the cotrol pael cover is removed. 7 - Bell Tamper Areas assiged to Bell Tamper will cause a Tamper alarm whe the Bell tamper loop is broke. Areas ot assiged to Bell Tamper will ever cause a Tamper alarm whe the bell tamper loop is broke. 8 - Auxiliar Tamper Areas assiged to Auxiliar Tamper will cause a Tamper alarm whe the Auxiliar tamper loop is broke. Areas ot assiged to Auxiliar Tamper will ever cause a Tamper alarm whe the auxiliar tamper loop is broke. 9 - Pael Speaker Areas assiged to Pael Speaker will cause the cotrol pael speaker to activate whe those areas are i alarm, etr ad exit etc. Areas ot assiged to Pael Speaker will ever cause the cotrol pael speaker to activate whe those areas are i alarm, etr ad exit etc Bell & Strobe op Areas assiged to Bell & Strobe op will cause the Bell/Strobe output o the cotrol pael to activate whe a alarm occurs i those areas. Areas ot assiged to Bell & Strobe op will ever cause the Bell/Strobe output o the cotrol pael to activate whe a alarm occurs i those areas Alarms Eg Reset Each area ca be programmed for Egieer or User reset followig a Itruder alarm. Areas Assiged to Alarms Eg Reset will respod as follows: The assiged areas ca ol be reset usig a Egieer code If Ati-code Reset is eabled (optio 14) the assiged areas ca also be reset usig the Ati-code Areas ot assiged to Alarms Eg Reset ca be reset with a User code that is valid for those areas Cofirmed Reset Each area ca be programmed for Egieer or User reset followig a Cofirmed alarm. Areas Assiged to Cofirmed Reset will respod as follows: If Ati-code Reset is eabled (optio 14) the assiged areas ca also be reset usig the Ati-code Areas ot assiged to Cofirmed Reset ca ol be reset with a User code that is valid for those areas providig that Alarms Eg Reset (optio 14) is also programmed for user reset Tamper Eg Reset Each area ca be programmed for Egieer or User reset followig a Tamper alarm (whe the area is uarmed). Areas assiged to Tamper Eg Reset will respod as follows: The assiged areas ca ol be reset usig a Egieer code If Ati-code Reset is eabled (optio 14) the assiged areas ca also be reset usig the Ati-code Areas ot assiged to Tamper Eg Reset ca be reset with a User code that is valid for those areas Ati-code Reset Each area ca be programmed for Ati-code Reset followig a Itruder or Tamper alarm. Areas assiged to Ati-code Reset will respod as follows: The assiged areas ca be reset usig the Ati-code as well as a Egieer code Areas ot assiged to Ati-code Reset ca ol be reset usig a Egieer code or User code. The assiged areas ca ol be reset usig a Egieer code 58 INS176-9 Areas ca ol be assiged to Ati-code Reset if the are also assiged to Alarms Eg Reset ATS Path Faults Areas assiged to ATS Path Faults (ATS = Alarm Trasmissio Sstem) will respod as follows whe a ATS fault occurs. All kepads will displa ATS Path Fault All kepads ad speakers assiged to the same area as the ATS Path Fault will geerate a Service toe ever 30 Secods util the fault is ackowledged b the User eterig a valid code for that area A assiged area ca be armed, as log as Arm With No ATS is also assiged to that area (see optio 16). However, a warig will be give to idicate the problem Areas ot assiged to ATS Path Faults will ever be affected b a ATS fault Arm With No ATS Areas assiged to Arm With No ATS (ATS = Alarm Trasmissio Sstem) ca be armed whe a ATS fault occurs i those areas (see optio 15). Areas ot assiged to Arm With No ATS ca ever be armed whe a ATS fault occurs i those areas (see optio 15) AC Mais Fail Areas assiged to AC Mais Fail will respod as follows whe a AC mais failure occurs. All kepads will displa AC Mais Fail All kepads ad speakers assiged to the same area as the AC Mais Fail will geerate a Service toe ever miute util the fault is ackowledged b the User eterig a valid code for that area A assiged area ca be armed, as log as Arm With AC Fail is also assiged to that area (see optio 18). However, a warig will be give to idicate the problem Areas ot assiged to AC Mais Fail will ever be affected b a AC mais failure Arm with AC Fail Areas assiged to Arm With AC Fail ca be armed whe a AC Mais fail occurs i those areas (see optio 17). Areas ot assiged to Arm With AC Fail ca ever be armed whe a AC Mais fail occurs i those areas (see optio 17) Full Arm Coms Areas assiged to Full Arm Coms will respod as follows:

59 P Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual If the selected area is full armed ad a Itruder alarm occurs i that area, Itruder alarm evets (for that area) are reported to the Alarm Receivig Cetre after a programmed Digi dela has expired Areas ot assiged to Full Arm Coms will ever report Itruder alarm evets to the Alarm Receivig Cetre whe the are full armed Part Arm Coms Areas assiged to Part Arm Coms will respod as follows: If a assiged area is part armed ad a Itruder alarm occurs i that area, Itruder alarm evets (for that area) are reported to the Alarm Receivig Cetre after a programmed Digi dela has expired Areas ot assiged to Part Arm Coms will ever report Itruder alarm evets to the Alarm Receivig Cetre whe the area is Part armed Uarm Fire Coms Areas assiged to Uarm Fire Coms will respod as follows: If a assiged area is uarmed ad a Fire alarm occurs i that area, Fire alarm evets (for that area) will be reported to the Alarm Receivig Cetre Areas ot assiged to Uarm Fire Coms will ever report Fire alarm evets to the Alarm Receivig Cetre whe the area is uarmed. Fire alarm evets are alwas reported to the Alarm Receivig Cetre whe the area is armed regardless of whether the area is assiged to this optio or ot Uarm Tamp. Coms Areas assiged to Uarm Tamp. Coms will respod as follows: If a assiged area is uarmed ad a 24Hr or Tamper alarm or reportable fault occurs i that area, the evet will be reported to the Alarm Receivig Cetre Areas ot assiged to Uarm Tamp. Coms will ever report 24Hr or Tamper alarm evets or faults to the Alarm Receivig Cetre whe the area is uarmed. 24Hr ad Tamper alarm evets are alwas reported to the Alarm Receivig Cetre whe the area is armed regardless of whether the area is assiged to this optio or ot Auto Arm Areas Areas assiged to Auto Arm Areas will respod as follows: Whe a assiged area is disarmed, the Auto Arm Dela timer will start (see page 62 for details) Ever time a detector i that area is activated, the timer is restarted If the timer is allowed to expire i.e. o detectors i the assiged area are activated, the area will arm itself Areas ot assiged to Auto Arm Areas will ever tr to arm themselves Area A Foer Area A ca be used as a commo area (automaticall arms last ad disarms first). Areas assiged to Area A Foer will cause the pael to respod as follows: Whe all assiged areas are armed, Area A will automaticall arm itself Whe a oe assiged area is disarmed, Area A will automaticall disarm itself Areas ot assiged to Area A Foer will ot affect the automatic armig of area A Log Part Omits Areas assiged to Log Part Omits respod as follows: Whe a assiged area is part armed, all the zoes that are omitted for that area are logged i the evet log Areas ot assiged to Log Part Omit will ever log the zoes that are omitted i the evet log whe the area is part armed Multi Kock Area Areas assiged to Multi Kock Area will respod as follows: Area Programmig Zoes with the Double Kock attribute will use the multiple kock value set up i sstem optios for zoe activatios (see page 67 for details) Areas ot assiged to Multi Kock Area will use the stadard 2 kocks for zoe activatios. For the Multi Kock Area feature to work, the zoe must be programmed with the Double Kock attribute (see page 51 for details) UDL Kepad Areas assiged to UDL Kepad ca be cotrolled i.e. armed, disarmed, reset etc. from the O Lie Kepad whe usig the Witex software ad a PC. Areas ot assiged to UDL Kepad caot be cotrolled i.e. armed, disarmed, reset etc. from the O Lie Kepad whe usig the Witex software ad a PC Auto Chime (C2A) Areas assiged to Auto Chime will respod as follows: Zoes assiged to the selected areas that have bee programmed for Chime will ol chime whe Custom Output 1, Stage A is o Areas ot assiged to Auto Chime will ol chime whe chime for that area is mauall eabled b the user. DD 243 Optios To compl with DD 243, durig the ormal etr dela, the cotrol pael must prevet a Cofirmed Itruder Alarm from beig reported to the Alarm Receivig Cetre. If a Portable ACE i.e. Electroic Keswitch, Ke Fob, Tag, Swipe Card etc is beig used for disarmig, it is permissible for the Cofirmed Itruder Alarm sigal to be re-eabled after the etr dela has expired. The followig two optios have bee provided to esure that the cotrol pael ca be programmed to compl with this stadard if required. WARNING Owig to the abilit to disable ALL of the cofirmatio facilities, the customer should be advised i writig b the alarm compa that ALL meas of alarm cofirmatio are disabled whe the iitial etr door is opeed. The alarm compa should the obtai writte acceptace from the customer of the disablig of the meas of alarm cofirmatio Cofirm i Etr Areas assiged to Cofirm i Etr will respod as follows: If the etr mode is started for the selected area ad a Cofirmed Itruder alarm occurs i that area, Cofirmed Itruder alarm evets (for that area) are reported to the Alarm Receivig Cetre Areas ot assiged to Cofirm i Etr will ever report Cofirmed Itruder alarm evets to the Alarm Receivig Cetre durig the etr mode. To compl with DD 243, areas must NOT be assiged to this optio, thus prevetig Cofirmed Itruder Alarms from beig reported to the Alarm Receivig Cetre durig the etr mode Cof. after Etr Areas assiged to Cof. After Etr will respod as follows: Alarm cofirmatio is ONLY disabled for the duratio of the Etr Time ad is RE-ENABLED oce the Etr Time has expired, after INS

60 Area Programmig which activatio of a further two zoes that are ot o the etr route must occur before the Alarm Cofirmatio output will activate Areas ot assiged to Cof. After Etr will ever report Cofirmed Itruder alarm evets to the Alarm Receivig Cetre after the etr dela has expired. To compl with DD 243, areas must NOT be assiged to this optio, thus prevetig Cofirmed Itruder Alarms from beig reported to the Alarm Receivig Cetre after the etr dela has expired. If a Portable ACE i.e. Electroic Keswitch, Ke fob, Tag, Swipe Card etc. is used to disarm the sstem, it is permissible for the Cofirmed Itruder Alarm sigal to be re-eabled after the etr dela has expired. I this case, areas CAN be assiged to Cof. After Etr Part Arm Eabled Areas assiged to Part Arm Eabled ca be Part Armed. Areas ot assiged to Part Arm Eabled caot be Part Armed Bell Squawk Areas assiged to Bell Squawk will respod as follows: Whe all of the assiged areas are full armed, the bell will activate oce for 2 secods, whe a oe of the assiged areas are disarmed, the bell will activate twice for 2 secods ad whe a oe of the assiged areas are disarmed followig a alarm, the bell will activate five times for 2 secods. Areas ot assiged to Bell Squawk will ot activate the Bell output whe armig or disarmig FOB After Etr Areas assiged to FOB After Etr ca ol be disarmed with a Radio FOB oce the Etr procedure has bee started. Areas ot assiged to FOB After Etr ca be disarmed with a Radio FOB at a time Armed = Coms Whe Areas are assiged to Armed = Coms the sstem will respod as follows: Commuicatios ad outputs (Alarm, Cofirmed etc.) for ALL areas will ol operate whe all of the assiged areas are armed. Whe No Areas are assiged to Armed = Coms the sstem will respod as follows: Commuicatios ad outputs (Alarm, Cofirmed etc.) for ALL areas will operate as ormal Wire Smoke Areas assiged to 2-Wire Smoke will register a Fire Alarm whe a 2-Wire Smoke detector activates. Areas ot assiged to 2-Wire Smoke will ot register a Fire Alarm whe a 2-Wire Smoke detector activates Faults Eg Reset Each area ca be programmed for Egieer or User reset followig a Fault. Areas Assiged to Faults Eg Reset will respod as follows: The assiged areas ca ol be reset usig a Egieer code If Ati-code Reset is eabled (optio 14) the assiged areas ca also be reset usig the Ati-code Areas ot assiged to Faults Eg Reset ca be reset with a User code that is valid for those areas No ATS Eg Reset Each area ca be programmed for Egieer or User reset followig a No ATS Available fault (ATS = Alarm Trasmissio Sstem). Areas Assiged to No ATS Eg Reset will respod as follows: The assiged areas ca ol be reset usig a Egieer code If Ati-code Reset is eabled (optio 14) the assiged areas ca also be reset usig the Ati-code Areas ot assiged to No ATS Eg Rst ca be reset with a User code that is valid for those areas. Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 38 - AC Fail Eg Reset Each area ca be programmed for Egieer or User reset followig a AC Mais Fail. Areas assiged to AC Fail Eg Reset will respod as follows: The assiged areas ca ol be reset usig a Egieer code If Ati-code Reset is eabled (optio 14) the assiged areas ca also be reset usig the Ati-code Areas ot assiged to AC Fail Eg Reset ca be reset with a User code that is valid for those areas Mask Whe Armed Areas assiged to Mask Whe Armed will register a Maskig fault whe the selected areas are armed ad a Maskig Fault occurs. Areas ot assiged Mask Whe Armed will ever register a Maskig fault whe the selected areas are armed ad a Maskig Fault occurs 60 INS176-9

61 P Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Area Programmig Time Arm Area Area Text Area Programmig Area Programmig Timers 6 Area Programmig Time Arm Areas Area A Armed b timer U Area B Armed b timer 5 Area B Armed b timer > 5 Area B Armed b timer 5 ad Disarm B b timer 3 ad Disarm B b timer > 3 ad Disarm B b timer 3 Use the SCR OLL ke to select a area or Group & Area Use kes 1-8 to selec t a time r e. g. 5 = T ime r 5 Press YES to select the disa rmed b timer Use kes 1-8 to selec t a time r e. g. 3 = T ime r 3 Area Programmig Area Programmig Timers 7 Area Programmig Area Text Text for Area A 4 Text for Area D ^Edit Text >ABC? Receptio Edit Tex^ >ABC Use kes 1-8 to selec t a Area or use the SCROLL ke to search e.g. 4 Pre s s NO to edit the Are a text Us e kes 0-9 to program te xt the s a me wa tha t a mobile phoe works Text ma be assiged to each of the areas o the sstem. This allows the user to select the areas b descriptio istead of a letter. A maximum of 16 characters ca be programmed for each of the areas. Text is programmed i a similar wa to mobile phoes. Select characters b pressig the correspodig ke the appropriate umber of times (to select a character o the same ke, press to move the cursor alog). The alarm sstem as a whole or a umber of idividual areas ca be automaticall armed or disarmed usig the built i cotrol timers. The 24 has 2 idepedet cotrol timers, the 48 has 4 idepedet cotrol timers the have 8 idepedet cotrol timers, ad the 640 has 8 idepedet cotrol timers for each of the 4 Area groups. These ma be cofigured to switch o ad off at differet poits of the da ad operate o differet das of the week (see page 68 for programmig details). INS

62 Global Optios Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 5.3 Global Optios Sstem Timers Global Optios Global Optios Sstem Timers Exit Settle Time 005 Secod(s) Global Bell Dl. 000 Miute(s)? Global Bell Dl. > 005 Miute(s) Us e the YE S ke to move to the ext timer or use the SC ROLL ke to search Eter a ew timer value e.g. 005 = 5 Miutes These timers cotrol various timig ad dela fuctios. Each timer ca be programmed for a value betwee 000 ad Exit Settle Time Whe usig the Etr/Exit or Exit Termiator armig mode, some detectors alog the exit route ca remai active for a umber of secods followig activatio. This timer esures that the detectors are give time to deactivate before the sstem/area arms. 1 - Global Bell Dl. This timer cotrols the dela betwee a Itruder alarm occurrig ad the Bell/Strobe output activatig. 2 - Global Bell Dur. This timer cotrols the duratio of the Bell output after a alarm has occurred ad a programmed Global Bell Dela time has expired. 3 - Double Kock Dl If a zoe has the Double Kock attribute a alarm will ol occur if the zoe activates twice withi this time widow or oce for the duratio of this time widow. If multi kocks has bee set up (see page 67 for details) the zoe ma have to be activated more tha twice. 4 - Beam Pair Time If a zoe has the Beam Pair attribute, a alarm will ol occur if aother zoe with the Beam Pair attribute (assiged to the same area) is activated withi this time widow. 5 - Activit Dela If a zoe has the Activit attribute ad it is ot activated durig this timer ad Cofig. optio 14 has bee set to View Act. Fault (see page 64 for details), it will be idicated to the user whe the tr to arm the sstem/area. 6 - Abort Dela Whe a Itruder alarm occurs this timer is started, if the area is disarmed withi this time widow a Abort evet will be reported to the Alarm Receivig Cetre. If the sstem is disarmed after this period the Abort evet is ot reported. 7 - Courtes Time This timer cotrols the duratio of the Courtes output tpe. The courtes output activates wheever a kepad is beig used ad durig the etr mode. 8 - Defer Armig B If a area tries to Time Arm ad a valid User code is etered, this timer is started ad the Time Armig procedure is postpoed. Whe this timer expires, the sstem/area will tr to arm itself agai. 9 - Auto Arm Dela Whe a area assiged to Auto Arm Areas is disarmed (see page 59 for details) this timer is started. Ever time a detector i that area is activated, the timer is restarted. If the timer is allowed to expire i.e. o detectors i the assiged area are activated, the area will arm itself Meu Time Out This timer cotrols the legth of time that a user ca remai i a meu before the sstem automaticall returs to the ormal da mode Pulse Period 1 This timer cotrols how log a output with the Pulse Period 1 attribute assiged to it will activate for Pulse Period 2 This timer cotrols how log a output with the Pulse Period 2 attribute assiged to it will activate for Pulse Period 3 This timer cotrols how log a output with the Pulse Period 3 attribute assiged to it will activate for ATS Fault Dela This timer cotrols the dela betwee a lie fault occurrig ad a audible idicatio beig geerated b the sstem AC Off Dela This timer cotrols the dela betwee a AC Mais failure occurrig ad a audible idicatio beig geerated b the 16 - Batt Test Period This timer cotrols the frequec of the damic batter test Batt Test Time This timer cotrols how log the damic batter test is carried out for Soak Test Time This timer cotrols the umber of das a zoe with the Test attribute will remai o test for Service Iterval This timer cotrols the frequec of the Service Required coditio occurrig Test Call Ever This timer cotrols how ofte a test call is made to the moitorig statio. 024 = dail etc Mi. Radom Time This timer cotrols the miimum legth of time that the Radom output attribute will activate for Max. Radom Time This timer cotrols the maximum legth of time that the Radom output attribute will activate for Door Strike Time This timer cotrols the legth of time that the Door Strike output will activate for wheever a code with the Door Strike attribute is etered Zoe Respose This timer cotrols the legth of time that a zoe with the Quick Resp. attribute, has to be activated for, i order to be recogised b the cotrol pael. 62 INS176-9

63 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 25 - Kepad PA Dela Whe kepad optio 6 is programmed as PA Delaed (see page 73 for details), ad a kepad PA alarm (1 & 3) is activated, this timer starts. If a User code is etered before this timer expires, o PA alarm will occur. However, if a User code is ot etered before this timer expires, a PA alarm will occur Cofirmatio Dl Whe a Itruder alarm occurs, this timer starts. If a secod (differet) zoe is activated withi this time widow, the Cofirmed output will activate. Whe this timer expires, the Cofirmed output will o loger activate Warig Dela Whe a Custom zoe with the Warig Req attribute (see page 52 for details) activates, this timer is started. If the zoe is still active whe this timer expires a warig toe or alarm will occur ad the Warig Output (see page 80 for details) will activate Kepad Lock Time Whe code tampers are programmed to lockout the kepad (see page 64 for details), the kepad will lock out for the duratio of this timer Eg. log off Dl This timer starts whe a Egieers code is etered. Whe the timer expires the egieer is automaticall logged out of egieer s mode. This timer is suspeded if there are tamper faults o the sstem allowig the egieer to remai i egieer s mode idefiitel whilst o site Fire Bell Dela This timer starts whe a fire alarm is geerated i a particular area. Whe the timer expires souders are activated i ALL areas Forced Etr Dl Whe a zoe with the Guard attribute (see page 51 for details) activates, this timer is started. For the duratio of this timer, a Etr/Exit 1 or 2 zoe with the Etr/Exit 2 attribute (see page 51 for details) will become a Guard zoe. Whe this timer expires, the Etr/Exit 1 or 2 zoe will revert back to its ormal mode of operatio Supervisio Time This timer cotrols the frequec at which the RadioPLUS detectors are required to report i to the cotrol pael Poll IP Ever This timer cotrols the frequec that the ComIP Polls the ARC. Sstem Cofig. Global Optios Global Optios Sstem Timers 1 Global Optios Sstem Cofig. Cofiguratio 00 No Bell Set Fail? Cofiguratio 09 NVM is Ulocked Cofiguratio 09 NVM is Locked Eter a cofiguratio umber or us e the S C R OL L ke to s e arc h e.g. 09 = NVM Ulocked Press NO to cha ge the cofig. optio Global Optios These optios cotrol how various sstem fuctios work No Bell Arm Fail If a area fails to arm, a Iteral alarm will occur ad the Strobe output will activate. Bell o Arm Fail If a area fails to arm, a Iteral alarm will occur ad the Bell output will activate for 10 secods. The Strobe output will also activate for 5 secods to idicate that the sstem has armed/disarmed Bell is a SAB The Bell output o the cotrol pael applies 0V whe active. Bell is a SCB The Bell' output o the cotrol pael removes 0V whe active Clock is 24Hr The sstem time is displaed i the 24-Hour format. Clock is 12Hr (Default) The sstem time is displaed i the 12-Hour format Auto BST/GMT The sstem clock will adjust itself at the begiig ad the ed of the summer (the clock will automaticall gai 1Hr o the last Suda i March ad lose 1Hr o the last Suda i October. Maual BST/GMT The sstem clock will ot adjust itself at the begiig ad the ed of the summer (the clock will have to be adjusted mauall) View Armed Areas Whe the sstem is part armed, the areas that are armed are displaed ad alarm iformatio is displaed before a valid User code is etered. Hide Armed Areas Whe the sstem is part armed, the areas that are armed are ot displaed ad alarm iformatio is ol displaed after a valid User code has bee etered. INS

64 Global Optios 05 Global Bell Time Whe all areas are armed, the sstem uses the Global Bell Dela ad Global Bell Duratio timers (see page 62 for details). Area Bell Time Whe all areas are armed, the sstem uses the Area Bell Dela ad Area Bell Duratio timers (see page 54 for details) Hr Omit Global 24-Hour tpe zoes ca be omitted from a kepad. 24Hr Omit Local Ol kepads assiged to the same area as the 24-Hour tpe zoes ca be used to omit the zoe Remove Omits Whe zoes have bee Omitted b a user, the zoes will be automaticall reistated b the sstem whe the area the are assiged to is ext disarmed. Leave Omits Whe zoes have bee Omitted b a user, the zoes will remai omitted util the user reistates them Override Com Dl If a area is Full armed ad a Itruder alarm occurs i that area, Itruder alarm evets (for that area) are reported to the Alarm Receivig Cetre immediatel. Eforce Com Dl If a area is Full armed ad a Itruder alarm occurs i that area, Itruder alarm evets (for that area) are reported to the Alarm Receivig Cetre after a programmed Coms dela has expired (see page 54 for details) NVM is Ulocked The factor default settigs ca be reloaded b pressig the Factor Restart butto durig power up. NVM is Locked The factor default settigs caot be reloaded b pressig the factor default butto durig power up. If the NVM is locked ad the Egieer User code has bee lost or forgotte, the PCB will have to be replaced Egieer Ol Access to the Egieers Programmig meus ca be obtaied b just eterig the Egieer User code. User + Egieer Access to the Egieers Programmig mode ca ol be obtaied, if a User (with the Egieer Access attribute) has authorised egieer access (see page 110 for details) Chime Audible Zoes programmed with the Chime 2 or 3 attribute will ol geerate a Chime toe. Chime Visible (Default) Zoes programmed with the Chime 2 or 3 attribute will geerate a Chime toe. The kepad will also displa the umber of the zoe that was activated Omit Tampers No A user caot omit Tamper faults o a zoe. Omit Tampers Yes A user ca omit Tamper faults o a zoe Offlie Pritig If a priter is plugged oto the cotrol pael, othig will be prited uless a pritout is requested (see page 120 for details). Olie Pritig If a priter is plugged oto the cotrol pael, athig that is logged i the evet log is also prited at the same time Hide Act. Fault If a zoe with the Activit attribute is ot activated durig the Activit Dela time widow, the area that the zoe is assiged to ca still be armed. However, this fault will be idicated to the user whe the tr to arm the area. View Act. Fault If a zoe with the Activit attribute is ot activated durig the Activit Dela time widow, the area that the zoe is assiged to caot be armed. This situatio ca ol be overcome b activatig the zoe. Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 15 - Hide Exit Errors If a user tries to arm a area ad there are zoes activated, the exit mode will cotiue (givig a visual ad audible idicatio that there is a problem). View Exit Error If a user tries to arm a area ad there are zoes activated, the exit mode is suspeded util all of the zoes are secure Eable Code Tampers 24 ivalid ke presses o a kepad will cause a Code Tamper coditio (see optio 17). No Code Tampers A Code Tamper coditio will ever occur whe the kes o a kepad are pressed more tha 24 times Code Tamper Alarm A Code Tamper coditio will cause a Tamper alarm i the areas that the kepad is assiged to. Code Tamper Lockout A Code Tamper coditio will cause the kepad to lockout for the duratio of the kepad lockout timer (see page 62). Optio 16 above must be set to eable code tampers i order for this optio to work Areas A-H & I-P The first 8 areas will be displaed as letters A through to H ad the last 8 areas will be displaed as letters I through to P. Areas 1-8 & I-P The first 8 areas will be displaed as umbers 1 through to 8 ad the last 8 areas will be displaed as letters I through to P Auto Area Select Whe a Egieers code is etered to gai access to the programmig mode, ALL Zoes ad Tampers are disabled i.e. if a Tampers, PA, Fire or Medical Alarms are activated - NOTHING WILL HAPPEN. Ma. Area Select Whe a Egieers code is etered to gai access to the programmig mode, the Egieer will have to select which areas are goig to be worked o. Zoes ad Tampers are ol disabled for the selected areas all other areas will respod to zoe activatios ad tampers as ormal Predictive Text Whe i text editig mode, the cotrol pael will automaticall select predictive text. Maual Text Edit Whe i text editig mode, the cotrol pael will automaticall select ormal text Short = Tamper The cotrol pael will see a zoe that is i the short circuit coditio as a Tamper. Short = Active The cotrol pael will see a zoe that is i the short circuit coditio as Active R/R=Reset Ol Whe 0V is applied to the cotrol pael R/R iput, a areas programmed for ati-code reset (see page 58 for details) that are i alarm, will be reset. R/R=Silece/RST Whe 0V is applied to the cotrol pael R/R iput a areas programmed for ati-code reset (see page 58 for details) that are i alarm, will be sileced. Whe 0V is applied to the R/R iput a secod time, the areas will be reset (this would ormall be used whe Audio Verificatio is required). 64 INS176-9

65 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 23 - User Code Pulse Eterig a user code which has a associated user output will cause the output to activate for the duratio of the door strike timer. User Code Latch Eterig a user code which has a associated user output will cause the output to toggle from off to o or from o to off Timed Test Call A test call to the Alarm Receivig Cetre will occur ever time the Test Call Ever timer expires. Test Call = CT4 A test call to the Alarm Receivig Cetre will occur ever time Cotrol Timer 4 activates Batt Test Timed A batter test will occur ever time the Batt Test Period timer expires. Batt Test = Disarm A batter test will occur ever time the sstem is disarmed or after the Batt Test Period timer has expired (whichever occurs first) Bell = 1st Alarm The Bell ad Strobe outputs will activate after a Itruder alarm (1st Alarm) occurs. Bell = 2d Alarm The Bell ad Strobe outputs will activate after a Cofirmed alarm (2d Alarm) occurs SNDR = 1st Alarm The iteral souders will soud after a Itruder alarm (1st Alarm) occurs. SNDR = 2d Alarm The iteral souders will soud after a Cofirmed alarm (2d Alarm) occurs Cof. = Istat Followig the armig of the sstem/area, if two zoes activate (causig a Cofirmed alarm), the sigal will be reported to the Alarm Receivig Cetre immediatel. Cof. = Delaed Followig the armig of the sstem/area, if two zoes activate (causig a Cofirmed alarm), the sigal will ol be reported to the Alarm Receivig Cetre after the Abort time has expired Abort=Eg.Reset A Itruder alarm that is aborted ca ol be reset b a Egieer/Ati-code. Abort=User Reset A Itruder alarm that is aborted ca be reset b a User. 30 Auto AV Output Whe usig the AV Module, if a microphoe is remotel selected, the correspodig output automaticall activates. Maual AV Output Whe usig the AV Module, if a microphoe is remotel selected, the correspodig output must be activated mauall Clock = 50Hz The iteral clock o the cotrol pael rus from the 50Hz mai frequec. Clock = Crstal The iteral clock o the cotrol pael rus from the built-i crstal Colum Prit Select this optio whe coectig a 80 Colum priter to the cotrol pael. 40 Colum Prit Select this optio whe coectig a 40 Colum priter to the cotrol pael Disable Text Areas that are armed are displaed as letters o the bottom lie of the displa i.e. Armed: AB.D Eable Text Areas that are armed are displaed usig their assiged text o the bottom lie of the displa i.e. Armed: Garage, Office etc. (a differet area is displaed ever secod). Global Optios EN50131 Eabled Kepad displa blakig is eabled i.e. the kepad will ol displa the time, date ad the baer message. If iformatio is available to be viewed i.e. AC Mais Fail, Lie Fault, Sstem Faults etc. the kepad will bleep ever 30 secods ad displa Sstem Alerts, this iformatio ca ol be viewed after a valid user code has bee etered. The kepad displa will the blak agai 30 secods after. The bell output will ot activate, if a alarm occurs durig the etr mode. Duress Codes ca ol be programmed b a egieer 35-2d Zoe = Cofirm After the etr timer has expired, activatio of 2 more zoes is required to geerate a Cofirmed alarm 1st Zoe = Cofirm After the etr timer has expired, activatio of 1 more zoe is required to geerate a Cofirmed alarm 36 - Kepads Global Kepads show iformatio for all areas. Kepads Local Kepads ol show iformatio that is relative to the area that the kepad is assiged to Pael Grade 3 All optios relatig to PD6662: 2004/EN Grade 3 are eabled automaticall. Also, the Ati-code reset becomes a 6-digit umber ad all user codes ca ol be programmed as 5 or 6 digits. Pael Grade 2 All optios relatig to PD6662: 2004/EN Grade 3 that are ot required for Grade 2 are disabled automaticall. Also, the Ati-code reset becomes the stadard 4 digit umber ad all user ad egieer codes ca be 4, 5 or 6 digits Disable FOB PA Whe a Smartke Trasmitter FOB is beig used with the alarm sstem, the Paic Alarm (PA) fuctio i.e. Pressig buttos 1 ad 2 together, is disabled. Eable RF FOB PA Whe a Smartke Trasmitter FOB is beig used with the alarm sstem, the Paic Alarm (PA) fuctio i.e. Pressig buttos 1 ad 2 together, is eabled Armed Mask=Fault If a Ati-maskig sigal is detected whe the sstem is armed, the cotrol pael will geerate a Fault respose. Armed Mask=Alarm If a Ati-maskig sigal is detected whe the sstem is armed, the cotrol pael will geerate a Alarm respose. 40 Silet RF FOB PA PA alarms geerated from a wireless FOB will cause a silet alarm. Audible FOB PA PA alarms geerated from a wireless FOB will cause a Audible alarm. 41 Moitor PSU Batter Batter faults from the PSU200XP are moitored. No PSU Batt Flts Batter faults from the PSU200XP are ot moitored. 42 Exp Loss Tamp A expader lost evet will geerate a tamper alarm. No Exp Loss Tamp A expader lost evet will geerate a fault coditio. 43 Soak Test War If zoes have bee placed o Soak Test, a warig will be show to the user at the time of armig. No Soak Test War If zoes have bee placed o Soak Test, o warig will be show to the user at the time of armig EN50131 Disabled The Cotrol Paels EN50131 optios are disabled. INS

66 Global Optios 44 FOB Batt War Whe durig armig if a low fob batter evet is received the armig will be cacelled ad the kepad will geerate a warig, the user will have to affirm the Arm with faults o the kepad before armig will proceed. Both the low batter ad the user ackowledgemet will be logged. No FOB Batt War Whe durig armig if a low fob batter evet is received the armig will proceed but the low fob batter will be logged i the evet log. 45 Etr Stra Eables Etr Stra to compl with BS8243 or EN This flag is selectable b cofigurig optio 46. No Etr Stra Disables Etr Stra 46 BS Etr Stra A secod alarm coditio durig the alarm otificatio period will immediatel expire the alarm otificatio timer. This will cause a cofirmed alarm message to be set to the arc ad logged i the evet log. No BS Etr Stra Secod ad subsequet alarm coditios durig the alarm otificatio period have o effect o the timer. 47 Tamp No Cofirm If a device has caused a ucofirmed alarm the a tamper from that same device will ot cause a cofirmed alarm. Tamper Cofirm If a device has caused a ucofirmed alarm the a tamper from that same device will cause a cofirmed alarm. 48 Radio 2 Step Arm Whe armig usig a wireless FOB. The armig procedure requires two steps. Radio 1 Step Arm Whe armig usig a wireless FOB. The armig procedure requires oe step. 49 Radio Step 1 Zoe Whe cofiguratio optio 48 is programmed as Radio 2 Step Arm the secod step of the armig procedure is the activatio of a zoe programmed as Guard Access. Radio Step 2 RKP Whe cofiguratio optio 48 is programmed as Radio 2 Step Arm the secod step of the armig procedure is cofirmatio via the kepad. 50 Cof Hold Up EN Oce a PA zoe is activated the hold-up timer is started (See Global Sstem Timers for Cofirmed PA Timer), the cofirmed alarm will geerate if oe of the followig happes, aother PA Zoe activated or a tamper from a device, multi-actio PA or a global tamper withi the timer period. No Cof Hold Up No cofirmed hold-up will be geerated. 51 Max Log msgs 3 Log evets from idividual sources are limited to 3. No Max Log msgs Log evets from idividual sources are ot limited to Code Etr Timed Whe 10 failed code attempts have bee made, the kepad will lock out for 90 secods. If the pael is grade 2 a further 10 failed code etr attempts the will kepad will locked out for 90 secods. If the pael is grade 3 the after ever sigle failed code etr attempt the kepad will lock out for 90 secods. After 21 failed code etr attempts the code tamper alarm is geerated ad logged. No code Et Time Failed code etr attempts will ot lock out kepads or geerate a code tamper Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 53 Eable PD6662:2010 The pael will be defaulted to operate accordig to PD6662:2010 Disable PD6662:2010 The pael will operate accordig to the requiremets of PD6662: INS176-9

67 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Sstem Optios Global Optios Global Optios Sstem Timers Global Optios Sstem Optios Advisor Volume Level = 5 Chime Volume Level = 2 Chime Volume Level =>2 8 Chime Volume Level = 8 Us e the YE S ke to move to the ext optio or use the SC ROLL ke to search Pre s s NO to edit the volume level These optios cotrol various sstem fuctios. E te r a value or use th e SCR OLL ke to ic rease or dec rease the value e. g. 8 = F ull Volume 0 - Advisor Volume Cotrols the volume of advisor toes (etr/exit etc.) from loudspeakers coected to the cotrol pael (Alarm toes are alwas full volume). 1 = mi, 8 = max. 1 - Chime Volume Cotrols the volume level of Chime toes from ALL loudspeakers. 1 = mi, 8 = max. 2 - No. Of Re-Arms Cotrols the umber of times that a zoe will re-arm. Oce the re-arm limit has bee reached, the zoe is Locked Out ad will ot cause a further Itruder alarms. 3 - Ati-code Resets Limits how ma times a user ca perform a Ati-code reset. Oce this limit is bee reached, the sstem ca ol be reset usig a Egieer code. This couter is reset ever moth or wheever a Egieers code is etered. 4 - Multiple Kocks Cotrols how ma times, a zoe with the Double Kock attribute, must be activated, before a alarm occurs. The multiple kock cout ca be applied to zoes o a area basis, see page 59 for details. 5 - Clock Adjustmet Adjusts the accurac of the clock b subtractig or addig time i secods at midight ever ight. 0 = -50, 50 = 0 (o correctio), 100 = Quick Cout Set the umber of 10milli Secod pulses that are required withi 30 Secods i order for a zoe with the Quick Respose attribute to activate. 7 - Modem Level Whe usig a Com2400 this optio allows adjustmet to the atteuatio of the modem. Modem Level Atteuatio (db) Laguage Selectio Various laguages are available for the cotrol paels. Listed below are the laguage sets, ad the laguages available. The Laguage set Global Optios umber is defied o the product label where applicable b LS1, LS2 or LS3. The 640 has all laguages listed available i the cotrol pael. 24/48/88/168 LS1 LS2 LS3 Eglish UK Eglish UK Eglish UK Eglish Eglish Eglish Swedish Spaish Russia Frech Italia Sloveia Belgia Dutch Polish Czech Text Daish Hugaria Germa Norwegia Estoia Fiish Eglish UK Eglish Swedish Frech Belgia Dutch Daish Norwegia Fiish Spaish 640 Italia Polish Hugaria Russia Sloveia Czech Germa Estoia 9 - Coutr Codes & Defaults Coutr codes are used to defie Telecoms requiremets, ad defaults are loaded if available whe the coutr code is chose. The followig coutr codes are available ad show the associated defaults loaded b the pael. Coutr Code Defaults Export 0 UK Russia 7 UK South Africa 27 South Africa Netherlads 31 UK Belgium 32 Norwa Frace 33 Frace Spai 34 UK Hugar 36 UK Ital 39 UK Czech 42 UK UK 44 UK Demark 45 Demark Swede 46 Swede Norwa 47 Norwa Polad 48 UK Germa 49 UK Filad 58 Norwa Australia 61 Australia Test 97 UK Themes 98 UK Chi 99 UK Estoia 172 (372) UK INS

68 Global Optios Moitor Hardware Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Cotrol Timers Global Optios Global Optios Sstem Timers 3 Global Optios Moitor Hardware Moitor Hardware P A O B A L * ATS Path Faults >P A O B A L * U Bell Tamper P A O>B A L * Bell Tamper P A O>* A L * Press NO to edit the optios Use kes 1-8 to selec t a a ttr ibute o r u se th e SCR OLL ke to searc h Press NO to select/deselect the optio The cotrol pael moitors ma iputs for fault coditios i.e. the pael lid tamper, bell tamper, aux fuse etc. Each oe of these optios ca be disabled to overcome problems related to the devices beig moitored. P - ATS Path Faults The Alarm Trasmissio Sstem is moitored for faults. A - AC Power Failure The AC Mais is moitored for faults. O - Power Outputs/Charger The Power outputs ad charger are moitored for faults. see page 106 for the list of Power Outputs moitored) B - Bell Tamper The exteral souder tamper loop is moitored for faults. A - Aux Tamper The auxiliar tamper loop is moitored for faults. L - Pael Lid Tamper The cotrol pael lid tamper is moitored for faults. B - Batter Faults The batter is moitored for faults. Global Optios Global Optios Sstem Timers 4 Global Optios Cotrol Timers Cotrol Timer 1a is O at >13:00 U Cotrol Timer 2a is O at >13:00? Cotrol Timer 2a is O at >11:52 Timer 2a O Das... 1 Timer 2a O Das Su... Cotrol Timer 2a is Off at >12:00? Cotrol Timer 2a is Off at >21:34 Timer2a Off Das... 1 Timer2a Off Das...Tu... Use the S C RO LL k e to s ele ct c otrol time r 1-8 E te r the a O time for e.g = 11:52 a m Press YES to select the a O T ime DAYS OF OPERATION Use kes 1-8 to selec t the das 1 = Suda through to 7 = Saturda (8 = Holida Date) e. g. 1 = S uda Press YES to select th e a O ff Ti me E ter the a Off Time for e.g = 9:34 pm Press YES to select th e a O ff Ti me DAYS OF OPERATION Us e k es 1-8 to s elect the da s e.g. 3 = Tuesda The 48 has 4 cotrol timers ad the 88,168 ad 640 have 8 cotrol timers. Each timer has two ON ad OFF times (a & b), ad ca be programmed to operate o a da of the week. Oce cofigured, the timers ca be used to arm or disarm areas, lockout users ad cotrol outputs. Whe programmig the Cotrol Timers ON time, pressig will brig a * up o the displa. This * idicates that the iteral souders will chime ever time the Cotrol Timers ON time is reached. Whe programmig the Cotrol Timers DAYS of operatio, pressig will brig HO up o the displa. This HO idicates that the cotrol timer will operate o a programmed Holida date. 68 INS176-9

69 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Global Optios Sstem Text Part Arm Text Global Optios Global Optios Sstem Timers 5 Global Optios Sstem Text YES to EDIT: Reset Message 4 YES to EDIT: Baer Message ^Edit Text >ABC? ABC A Edit T^xt ^ABC Edit Text >CLR? ABC Alarms 2001 Edit Text >12^ Use kes 1-6 to select a te xt optio or us e the SCR OLL ke to search i.e. 5 = B aer Message Press YES to edit the text The sstem has 7 programmable messages. Us e kes 0-9 to progra m te xt the sa me w a tha t a mobile phoe works P res s NO followe d b YE S to clear the scree or keep pressig NO to chage betwee upper case, lower case, umerica l ad predictive text 1 - Reset Message This 32-character message is displaed wheever the cotrol pael requires a Egieer reset. 2 - Ati-code Msg. This 32-character message is displaed wheever the cotrol pael requires a Ati-code Reset. 3 - Service Message This 32-character message is displaed wheever the cotrol pael requires Datime reset. 4 - Locatio Text This 32-character message is displaed wheever the egieer views the locatio text i Egieer Utils. 5 - Baer Message This 16-character message is displaed above the time ad date wheever the cotrol pael is uarmed or full armed. 6 - Part Arm Baer This 16-character message is displaed above the time ad date wheever the cotrol pael is part armed. 7 - Priter Header This 16-character header will be prited wheever a log pritout is take from the cotrol pael or a Short Message Service (SMS) text message is set to a mobile phoe. Global Optios Global Optios Sstem Timers 6 Global Optios Sta Arm Text Eveig Arm Text for Sta 1 3 Bedtime Arm 2 Text for Sta 3 ^Edit Text >TXT Bedtime Arm 2 ^Edit Text ^CLR ^Edit Text >TXT? Nightime settig ^Edit Text >TXT Use kes 1-3 to selec t a s ta arm group or us e the SCR OL L ke to searc h e.g. 3 = Sta Arm 3 Press No to edit the text Press NO to select clear scree Press YES to clear scree Us e kes 0-9 to progra m te xt the sa me wa tha t a mobile phoe works Text ma be assiged to Part Arm 1, 2 or 3 to allow the user to select the correct Part Arm b descriptio istead of umber. A maximum of 16 characters ca be programmed for each of the Part Arms. The 3 Part Arm messages are global messages ad will appear wheever oe of the part arms are selected regardless of which area is beig part armed. Text is programmed i a similar wa to mobile phoes. Select characters b pressig the correspodig ke the appropriate umber of times (to select a character o the same ke, press to move the cursor alog). INS

70 Global Optios Holida Dates Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Speaker Toes Global Optios Global Optios Global Optios Sstem Timers 7 Global Optios Sstem Timers 8 Global Optios Holida Dates Global Optios Speaker Toes Holida Date 1> 00/00/00 U Use the SCR OLL ke to s ele ct a Holida Date Speaker Toes F A F S E X C Pre s s No to edit the souder optio Holida Date 3> 00/00/00 Holida Date 3> > 00/00/00? Eter ew date > 03/05/01 Us e ke s 0-9 to eter the ew date DD/MM/YY e.g = 3rd Ma 2001 Fire Toes >F A F S E X C U Etr Toes F A F S>E X C Etr Toes F A F S>* X C Use kes 1-8 to select/deselec t the souder optio or use the SCR OLL ke to searc h Press No to select/deselect the souder optio The sstem has 8 programmable holida dates. The holida dates are pre-defied dates o which the Cotrol Timers will ot operate. Example Cotrol Timer 1 is programmed to operate betwee the hours of 8pm ad 8am o Moda through to Frida (for the purpose of armig the cotrol pael). Because Bak Holidas ormall fall o Modas the pael would disarm itself leavig the premises uprotected. Christmas da 2001 falls o a Tuesda Uder ormal coditios the Cotrol Timer will operate o a Tuesda The 25/12/01 is programmed as a Holida Date The Cotrol Timer does ot operate o Tuesda 25 th December 2001 ad the premises remais protected at all times The speaker output o the cotrol pael ca be programmed so that certai tpes of toes are ot geerated. Whe deselected, Fire, Alarms, Fault, Service, Etr, Exit ad Chime toes will ot be heard. Select toes b pressig kes 1 to 8 (a letter o the displa meas the toe is selected, a Dot o the displa meas the toe is ot selected). F - Fire Toes O Fire alarm toes will be geerated b the cotrol pael souder/speaker. A - Alarm Toes O Itruder alarm, Tamper alarm ad PA alarm toes will be geerated b the cotrol pael souder/speaker. F - Fault Toes O Fault toes will be geerated b the cotrol pael souder/speaker. S - Service Toe O Service ad Warig toes will be geerated b the cotrol pael souder/speaker. E - Etr Toes O Etr toes will be geerated b the cotrol pael souder/speaker. X - Exit Toes O Exit toes will be geerated b the cotrol pael souder/speaker. C - Chime Toes O Chime 1, 2 ad 3 toes will be geerated b the cotrol pael souder/speaker. 70 INS176-9

71 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Global Optios PC Output Text Custom O/P Text Global Optios Global Optios Global Optios Sstem Timers 9 Global Optios Sstem Timers 9 Global Optios PC Output Text Global Optios Custom O/P Text PC Output 1 Text 4 Use kes 1-8 to selec t a text optio or us e the SCR OL L ke to searc h i. e. 4 = PC O utput 4 Text Custom O/P1 Text 3 Use kes 1-4 to selec t a text optio or us e the SCR OL L ke to searc h i. e. 3 = C ustom O/P 3 Text PC Output 4 Text Press NO to edit the text Custom O/P3 Text Press NO to edit the text ^Edit Text >ABC? Cetral Heatig Edit Text ^AB^ Edit Text >CLR? Cetral Heatig Edit Text >12^ Us e kes 0-9 to progra m te xt the sa me wa tha t a mobile phoe works P res s NO followe d b YE S to clear the scree or keep pressig NO to chage betwee upper case, lower case, umerica l ad predictive text Text ma be assiged to PC Cotrol Outputs 1 to 8 to allow the user to select the correct Output b descriptio istead of umber. A maximum of 16 characters ca be programmed for each of the PC Outputs. ^Edit Text >ABC? Co mm s Act i ve Edit Text ^AB^ Us e kes 0-9 to progra m te xt the sa me wa tha t a mobile phoe works Text ma be assiged to Custom Outputs 1 to 4 to allow idicatio o the kepads displa whe the output is active (see page 82 for details). Outputs 1 & 2 are silet ad outputs 3 & 4 give a audible warig ever 30 secods for 3 miutes or util a code is etered or RESET is pressed. Text is programmed i a similar wa to mobile phoes. Select characters b pressig the correspodig ke the appropriate umber of times (to select a character o the same ke, press to move the cursor alog). Text is programmed i a similar wa to mobile phoes. Select characters b pressig the correspodig ke the appropriate umber of times (to select a character o the same ke, press to move the cursor alog). INS

72 Kepad Setup Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 5.4 Kepad Setup Kepad Setup RKP*1,1 Areas: A... RKP*2,3 Areas: A... R? Use kes 1-8 to s elec t a k epad ad press 0 to toggle betwee etworks e.g. 0, 3 = Network 2, Kepad 3 (a * to the left of the device umber idicates that the device is fitted) Press NO to edit the kepad areas RKP*2,3 Areas: > A******* < 2 Use kes 1-8 to select a area e.g. 2 = B. Use the a re a ke to toggle betwe e are as A to H ad I to P s ee be low for 640 RKP*2,3 Areas: > AB****** < RKP*2,3 Mappig Z1-000, Z2-000 R Press NO to map the kepa d zoes E ter a zoe umber or pre ss YE S to move to zoe B Eter a zoe umbe r e.g. 011 Z1->000, RKP*2,3 Z2- Mappig 000 Z1- RKP*2,3 000, Z2->000 Mappig? Press No to edit the kepad optios Use kes 1-8 to selec t a kepad optio or use the S C R OL L ke to s e arc h Press No to select/deselect the kepad optio RKP*2,3 Mappig Z1-000, Z2->011 RKP*2,3 Optios: * * * T * * * * R PA Disabled >* * * T * * * * U PA is Silet * * * T>* * * * PA is Silet * * * T>S * * * Press NO to edit the volume level Use the SCR OLL ke to adjust the volume level up & dow or eter a va lue RKP*2,3 Volume: Level = 4 R Press No to edit the souder optios RKP*2,3 Volume: Level =>4 U Use kes 1-8 to selec t a souder optio or use the S C R OL L ke to s e arc h RKP*2,3 Volume: Level =>5 Press No to select/deselect the souder optio RKP*2,3 Souds: F A F S E X C * Fire Toes >F A F S E X C * U Etr Toes F A F S>E X C * Etr Toes F A F S>* X C * RKP*2,3 Areas:1 A... RKP*2,3 Areas:1 ABCDEFGH< ******* A CP / Use the A k e to switch betwee Area Groups 1,2,3 & 4 Use the C hime & Part kes to sc roll betwe e Are a G roups 1, 2, 3 & 4 A RKP*2,3 Areas:1 *******>IJKLMNOP U se the Area ke to select either A-H or I-P a rea s. Use the umeric buttos 1-8 to toggle the require d are as o or off 72 INS176-9

73 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Kepad Areas Kepads ca be assiged to a umber of areas, assigig a kepad to a area determies: Which areas the souder ad speaker output i the kepad will geerate toes for i.e. if the kepad is assiged to areas A ad C, the souder/speaker will ol operate whe areas A or C are i alarm, etr, exit etc. Which areas ca be armed or disarmed from that kepad whe usig codes that have the Local Armig or Local Disarmig attributes (see page 110 for details) Which areas will cause a Tamper alarm whe the kepad cover is removed Kepad Zoe Mappig The zoes i the kepad eed to be mapped to a valid zoe umber before the ca be used as part of the sstem i.e. Kepad 1 Zoe 1 could be mapped to Zoe 5 (pael) ad Zoe 2 could be mapped to Zoe 25 (expader 3) etc. Util mapped, the zoes i the kepads will ot work. A kepad zoe ca be mapped to a zoe umber o the sstem, however, whe mapped to a zoe umber that alread exists i.e. Zoe 5 (pael), that zoe ca o loger be used. If a zoe is mapped to a zoe umber ot alread o the sstem i.e. Zoe 25 (expader 3) ad expader 3 is the added, that zoe o the expader (Zoe 25) caot be used. If ou wish to use the zoe o the expader, the kepad zoe must be remapped to a differet umber. If a zoe is remapped to a differet umber, the ew zoe umber must be treated as a ew zoe o the sstem ad therefore eeds to be programmed accordigl (the zoe programmig will NOT automaticall follow the mappig). Kepad Optios These 8 optios cotrol various kepad fuctios: Select optios b pressig kes 1 to 8 (a letter o the displa meas the optio is selected, a Dot o the displa meas the optio is ot selected). P - PA Eabled Pressig kes 1 & 3 together will cause a PA alarm. F - Fire Eabled Pressig kes 4 & 6 together will cause a Fire alarm. M - Medical Eabled Pressig kes 7 & 9 together will cause a Medical alarm. T - Tamper Eabled Removig the kepad cover will cause a Tamper alarm. A - PA is Audible A kepad PA (1 & 3) will cause a audible PA alarm. D - PA is Delaed Whe the kepad PA buttos (1 & 3) are pressed, the Kepad PA Dela timer starts, if a User code is etered before the timer expires, o PA alarm will occur. If a User code is ot etered before the timer expires, a PA alarm will occur (see page 63 for details). Q - Quick Arm is Eabled Pressig the Area or Part kes will Arm or Part Arm the areas that the kepad is assiged to without the eed to eter a User code first. O - Ifo.LED> Output The Ifo. LED o the kepad comes o whe the kepad output activates ad goes off whe the kepad output deactivates. Kepad Speaker Volume Kepad Setup This optio cotrols the volume level of advisor toes from loudspeakers coected to the kepads. Advisor toes cosist of Etr/Exit ad Warig tpe toes. 1 = miimum; 8 = maximum. Alarm toes are alwas full volume. Kepad Souder Optios The souder ad speaker output i the kepad ca be programmed so that certai tpes of toes are ot geerated. Whe deselected, Fire, Alarms, Fault, Service, Etr, Exit ad Chime toes will ot be heard. Select toes b pressig kes 1 to 8 (a letter o the displa meas the toe is selected, a Dot o the displa meas the toe is ot selected). F - Fire Toes O Fire alarm toes will be geerated b the kepad souder/speaker. A - Alarm Toes O Itruder alarm, Tamper alarm ad PA alarm toes will be geerated b the kepad souder/speaker. F - Fault Toes O Fault toes will be geerated b the kepad souder/speaker. S - Service Toe O Service ad Warig toes will be geerated b the kepad souder/speaker. E - Etr Toes O Etr toes will be geerated b the kepad souder/speaker. X - Exit Toes O Exit toes will be geerated b the kepad souder/speaker. C - Chime Toes O Chime 1, 2 ad 3 toes will be geerated b the kepad souder/speaker. K - Use Kepad Areas Whe selected, the kepad souder ad armig cotrol is determied b the area that the kepad is assiged to. Whe deselected, the kepad becomes a Area Arm Suite cotroller (see page 55 for details). This allows differet combiatios of areas to be armed or disarmed depedig o which kepad is used ad operates as follows: Kepad 1 = Area Arm Suite 1, Kepad 2 = Area Arm Suite 2, Kepad 3 = Area Arm Suite 3 etc. Whe a User code is etered at a kepad, oe of the Area Arm Suites is selected (depedig o which kepad was used) ad the areas cotaied withi that suite arm usig the armig mode for that suite, the kepad souder will also follow the areas defied b the suite. INS

74 Expader Setup Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 5.5 Expader Setup Expader Setup Exp.*1,1 Areas: A... Exp.*1,5 Areas: A... Exp.*1,5 3 R R Text: Exp.*1,5>Aux I/P Not Used R Exp.*1,5 Volume: Volume = 4 R Us e kes 1-8 to se le ct a expader a d press 0 to toggle betwee etworks e.g., 3 = Network 1, Kepad 5 (a * to the left of the device umber idicates that the device is fitted) Press NO to edit the expader areas Press NO to edit the expader text Press NO to edit the Auxiliar Iput Pre s s NO to edit the expader Volume level Press No to edit the souder optios Exp.*1,5 Areas: > A******* < ^Edit Text >ABC Exp.*1,5>Aux I/P Not Used Exp.*1,5 Volume: Volume =>4 Use kes 1-8 to select a area e.g. 2 = B. Use the area ke to toggle betwee areas A to H ad I to P. F or 640 s ee below 2 Use the ke pa d to program te xt the s a me wa tha t a mobile phoe works? U s e th e S CROLL ke to select a iput tpe U U s e th e S CROLL ke to adjust the volume level U Use kes 1-8 to selec t a souder optio or use the S C R OL L ke to s e arc h Exp.*1,5 Areas: > AB****** < I Receptio Edit Text ^>ABC Exp.*1,5>Aux I/P Auxiliar Tamper Exp.*1,5 Volume: Volume =>5 Press No to select/deselect the souder optio Exp.*1,5 Souds: F A F S E X C Fire Toes >F A F S E X C U Etr Toes F A F S>E X C Etr Toes F A F S>* X C EXP. 1,1 Areas1 A... EXP. 1,1 Areas1 ABCDEFGH< ******* A CP / Use the A k e to switch betwee Area Groups 1,2,3 & 4 Use the C hime & Part kes to sc roll betwe e Are a G roups 1, 2, 3 & 4 A EXP. 1,1 Areas1 *******>IJKLMNOP U se the Area ke to select either A-H or I-P a rea s. Use the umeric buttos 1-8 to toggle the require d are as o or off 74 INS176-9

75 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Expader Areas Expaders ca be assiged to a umber of areas, assigig a expader to a area determies: Which areas the speaker output o the expader will geerate toes for i.e. if the expader is assiged to areas A ad C, the speaker will ol operate whe areas A or C are i alarm, etr, exit etc. Which areas will cause a Tamper alarm whe the expader cover is removed Expader Locatio Text Each expader ca be assiged up to 16 characters of text. This text ca be used to describe where the expader is located withi the buildig. Text is programmed i a similar wa to mobile phoes. Select characters b pressig the correspodig ke the appropriate umber of times (to select a character o the same ke, press the ke to move the cursor alog). Expader Auxiliar Iput Each expader has a iput that ca be programmed for oe of the followig optios. If ot beig used, the iput must be programmed as Not Used (Default = Not Used). Not Used Never moitored b the sstem. Auxiliar Tamper Normall used for moitorig the box tamper of auxiliar devices such as power supplies etc (remove 0V for Tamper alarm). Bell Tamper Normall used for moitorig Bell Tamper returs (remove 0V for Tamper alarm). Remote Reset Normall used to reset the sstem/area followig a Itruder alarm (the area must also be programmed for Ati-code reset) see page 58 for details (appl 0V to reset). Lie Fault +ve Normall used to idicate a telephoe lie fault (remove 0V for Lie Fault). Lie Fault -ve Normall used to idicate a telephoe lie fault (appl 0V for Lie Fault). Silece Souders Normall used to silece the Iteral souders followig a Itruder alarm ad would be used i cojuctio with Audio Verificatio uits (appl 0V to silece). Global Omit Ke Normall wired to a ke switch. Whe the ke switch is activated, all zoes (with the Omit attribute) assiged to the same area as the expader, will be omitted (0V removed for omit). Local Omit Ke Normall wired to a ke switch. Whe the ke switch is activated, all zoes (with the Omit attribute) wired to the expader, will be omitted (0V removed for omit). PSU Moitor Normall used to moitor a Power Suppl for faults, see page 35 for wirig details. Defer Auto Armig Normall used to defer the automatic armig of a area (appl 0V to defer). Expader Speaker Volume Expader Setup This optio cotrols the volume level of advisor toes from loudspeakers coected to the expaders. Advisor toes cosist of Etr/Exit ad Warig tpe toes. 1 = miimum; 8 = maximum. Alarm toes are alwas full volume. Expader Souder Optios The speaker output o the expader ca be programmed so that certai tpes of toes are ot geerated. Whe deselected, Fire, Alarms, Fault, Service, Etr, Exit ad Chime toes will ot be heard. Select toes b pressig kes 1 to 8 (a letter o the displa meas the toe is selected, a Dot o the displa meas the toe is ot selected). F - Fire Toes O Fire alarm toes will be geerated b the expader souder/speaker. A - Alarm Toes O Itruder alarm, Tamper alarm ad PA alarm toes will be geerated b the expader speaker. F - Fault Toes O Fault toes will be geerated b the expader speaker. S - Service Toe O Service ad Warig toes will be geerated b the expader speaker. E - Etr Toes O Etr toes will be geerated b the expader speaker. X - Exit Toes O Exit toes will be geerated b the expader speaker. C - Chime Toes O Chime 1, 2 ad 3 toes will be geerated b the expader speaker. INS

76 Sstem Outputs Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 5.6 Sstem Outputs Sstem Outputs Sstem Outputs Pael Outputs 1 Sstem Outputs Digi Outputs Use kes 1-8 to select a output tpe or use the SCR OL L ke to searc h e.g. 1 = Digi Outputs Area:64. 1 ABCDEFGHIJKLMNOP Area:64. 1 ABCDEFGH< ******* CP / U se the C hime & Part kes to sc roll betwe e Are a G roups 1, 2, 3 & 4 Digi Output 1 Not Used (off) 3 Digi Output 3 Not Used (off) Eter Output Number e.g. 3 A Area:64. 1 *******>IJKLMNOP Use the Area ke to select either A-H or I-P a rea s. Us e the ume ric buttos 1-8 to toggle the require d are as o or off Digi Output 3 > Not Used Press YES to edit the selected optio 0 Digi Output 3 > Not Used 1 2 Digi Output > Sstem Tpe Digi Output 3 > Area Tpe Eter Output Tpe e.g. 13 Eter Output Tpe e.g. 06 Sstem output>13 Sstem Ope Area:11<A******* Fire Alarm Use kes 1-8 to selec t a area, use the AR EA ke to toggle betwee areas A to H ad I to P ( 168 ol) for 640 s ee a bove Area:1>A**D**** Fire Alarm 3 Digi Output 3 > Zoe Tpe Eter Zoe Number e.g. 011 Digi Output 3 Zoe011<Mimic Eter Zoe Tpe e.g. 2 (alarm) Digi Output 3 Zoe011>alarm 4 Digi Output 3 > User Tpe Eter User Code Number e.g. 016 Digi Output 3 016<Code Etered 5 Digi Output 3 > Cotrol Timer E te r Timer Number e.g. 7 Digi Output 3 Cotrol Timer 7< 6 Digi Output 3 > PC Cotrol Eter PC Cotrol Number e.g. 4 Digi Output 3 PC Cotrol 4< 7 Digi Output 3 > Door Cotrol E ter Door Cotrol Number e.g. 4 Digi Output 3 Door Cotrol>1,4 Digi Output 3 Sstem Ope To P rogram the Output Attributes (if R equired) Press NO to edit the a ttribute s Use kes 1-8 to selec t a a ttri bute o r u s e th e SCR OL L ke to searc h Press No to select/deselect the attribute Digi O/P 3 Att: * * * * * * * * User Test >* * * * * * * * U Iverted *>* * * * * * * U Iverted *>I * * * * * * If X-10 Outputs are beig programmed X-10 Output 3 House A Uit 01 X-10 Output 3 Press NO to edit the H ouse & Uit Numbers Use kes 0-9 to selec t a Hous e N umber or us e the SCR OL L ke to searc h P res s YE S to Acce pt a d move to the Uit Numbe r, T he use kes 0-9 to s ele ct a Hous e N umber or us e the SCR OL L ke to searc h X-10 Output 3 X-10 Output 3 House >A Uit 01 U House >F Uit 01 Press NO to edit the expader text ^Edit Text >ABC Use the ke pa d to program te xt the sa me wa tha t a mobile phoe works? I Receptio Edit Text ^>ABC X-10 Output 3 House F Uit>14 76 INS176-9

77 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Sstem Outputs Available Outputs Various sets of programmable outputs ca be foud o the cotrol pael, kepads, expaders ad output modules. Pael Outputs Pael outputs 1-5 are located o the top right had corer of the cotrol pael ad ca be programmed to a of the output tpes listed (see page 34 for wirig details). Digi Outputs Digi outputs 1-8 are located o the left had side of the cotrol pael ad ca be programmed to a of the output tpes listed (see page 34 for wirig details). Digi Chaels Digi chaels 1-8 are for the Com300 ad Com2400 plug-o commuicators ad ca be programmed to a of the output tpes listed. RedCARE/Rela Pis RedCARE or Rela Pis 1-8 are for a plug o RedCARE or RM8 Rela module ad ca be programmed to a of the output tpes listed. Kepad Outputs Kepad outputs are for the outputs o the remote kepads (see page 22 for details) ad ca be programmed to a of the output tpes listed. Wire as per Pael Outputs show o page 34. Expader Outputs Expader outputs are for the outputs o the zoe/output expaders (see page 23 for details) ad ca be programmed to a of the output tpes listed. Wire as per Pael Outputs show o page 34. Custom Outputs Custom outputs are NOT phsical outputs the are Software outputs that ca be cofigured to operate uder certai coditios (see page 81 for details). Oce cofigured these outputs ca the be assiged to a phsical output (see sstem outputs 22-27). X-10 Outputs X-10 outputs are NOT phsical outputs the are Software outputs that ca be cofigured to operate devices that are coected to a X- 10 cotroller. These outputs ca also be assiged a house ad uit umber alog with descriptive text. (see page 81 for details). Programmig Outputs Whe programmig outputs, select a output group ad a output tpe from that group s list (each output group has its ow output tpes) the select attributes (if required). Output Group + Output Tpe + Output Attributes = Output Programmed. Output Group - Not Used Ol the followig output tpe is available: Not Used (off) This output tpe ever activates. Output Group - Sstem Select a output tpe from the followig optios: 00 - ATS Path Fault This output tpe activates whe a fault is detected with the Alarm Trasmissio Sstem ad deactivates whe the fault is cleared Mais Power Off This output tpe activates whe o AC Mais is detected o the cotrol pael ad deactivates whe mais is detected Aux Fuse Blow This output tpe activates whe the Auxiliar fuse (F1) fails ad deactivates whe the sstem is reset Bell Tamper This output tpe activates whe the cotrol pael Bell tamper or a expader iput (programmed as Bell tamper) is activated, causig a Tamper alarm o the sstem, ad deactivates whe the Tamper alarm is reset Auxiliar Tamper This output tpe activates whe the cotrol pael Aux tamper or a expader iput (programmed as Auxiliar tamper) is activated, causig a Tamper alarm o the sstem, ad deactivates whe the Tamper alarm is reset Pael Lid Tamper This output tpe activates wheever the pael cover is removed, causig a Tamper alarm o the sstem, ad deactivates whe the Tamper alarm is reset Egieer Workig This output tpe activates wheever a Egieer code is etered to access the programmig meu ad deactivates whe the egieer logs off Cofirm Devices This output tpe activates whe the cotrol pael requires devices to be cofirmed ad deactivates whe the devices are cofirmed (see page 117 for details) Service Required This output tpe activates whe the Service Iterval timer expires ad deactivates whe a Egieer code is etered (see page 62 for details) Bell Fuse Blow This output tpe activates whe the cotrol pael bell fuse (F4) fails ad deactivates whe the sstem is reset Batter Fault This output tpe activates whe the sstem detects a fault with the stadb batter, ad deactivates whe the fault clears Batter Test O This output tpe activates whe the Batter Test starts, ad deactivates whe the test expires (see page 62 for details) Courtes Light This output tpe activates whe the Courtes timer starts, ad deactivates whe the timer expires (see page 62 for details) Sstem Ope This output tpe activates whe all areas are uarmed, ad deactivates whe a area is armed Full Arm This output tpe activates whe the sstem is full armed ad deactivates whe the sstem is disarmed Digi Failed This output tpe activates whe the plug-o commuicator fails to report to the Alarm Receivig Cetre (after 3 diallig attempts), ad deactivates the ext time the commuicator successfull reports to the Alarm Receivig Cetre Digi Successful This output tpe activates whe the plug-o commuicator successfull reports to the Alarm Receivig Cetre ad deactivates the ext time the commuicator is triggered Digi Active This output tpe activates whe the plug-o commuicator is triggered ad deactivates whe the commuicator shuts dow. INS

78 Sstem Outputs 18 - UDL Lockout This output tpe activates whe a attempt is made to upload/dowload with icorrect site details more tha three times ad deactivates after 4 hours or after a valid User code is etered UDL Call Active This output tpe activates whe a upload/dowload is started ad deactivates whe the upload/dowload fiishes UDL Eabled This output tpe activates whe Eable UDL/Egieer is eabled ad deactivates whe Eable UDL/Egieer is disabled (see page 110 for details) Cofirmed Alarm If the sstem is alread i alarm, this output tpe activates whe a differet zoe (ot o the etr route) is activated ad deactivates at the ed of the Cofirmatio time, whe a code is etered withi the Abort time or whe the alarm is reset Custom1 Stage A This output tpe operates whe Custom Output 1 Stage A activates ad deactivates whe Custom Output 1 Stage A deactivates Custom1 Stage B This output tpe operates whe Custom Output 1 Stage B activates ad deactivates whe Custom Output 1 Stage B deactivates Custom1 Stage AB This output tpe operates whe Custom Output 1 Stage A or B activates ad deactivates whe Custom Output 1 Stage A deactivates Custom2 Stage A This output tpe operates whe Custom Output 2 Stage A activates ad deactivates whe Custom Output 2 Stage A deactivates Custom2 Stage B This output tpe operates whe Custom Output 2 Stage B activates ad deactivates whe Custom Output 2 Stage B deactivates Custom2 Stage AB This output tpe operates whe Custom Output 2 Stage A or B activates ad deactivates whe Custom Output 2 Stage A deactivates Radio-Pad Failed This output tpe activates whe the radio pad fails to commuicate with the Alarm Receivig Cetre ad deactivates whe the radio pad successfull commuicates Radio Successful This output tpe activates whe the radio pad successfull commuicates with the Alarm Receivig Cetre ad deactivates whe the radio pad fails to successfull commuicate No Radio Sigal This output tpe activates whe the Radio-Pads forward sigal is lost ad deactivates whe the sigal is regaied Radio-Pad Lost This output tpe activates whe the Radio-Pad stops commuicatig with its base statio or the cotrol pael ad deactivates whe commuicatio starts agai. 32 Custom3 Stage A This output tpe operates whe Custom Output 3 Stage A activates ad deactivates whe Custom Output 3 Stage A deactivates Custom3 Stage B This output tpe operates whe Custom Output 3 Stage B activates ad deactivates whe Custom Output 3 Stage B deactivates Custom3 Stage AB This output tpe operates whe Custom Output 3 Stage A or B activates ad deactivates whe Custom Output 3 Stage A deactivates Custom4 Stage A This output tpe operates whe Custom Output 4 Stage A activates ad deactivates whe Custom Output 4 Stage A deactivates Custom4 Stage B This output tpe operates whe Custom Output 4 Stage B activates ad deactivates whe Custom Output 4 Stage B deactivates. Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 37 - Custom4 Stage AB This output tpe operates whe Custom Output 4 Stage A or B activates ad deactivates whe Custom Output 4 Stage A deactivates Com 1 Fault This output tpe activates whe whatever is coected to Com Port 1 stops commuicatig with the cotrol pael ad deactivates whe commuicatio starts agai Com 2 Fault This output tpe activates whe whatever is coected to Com Port 2 stops commuicatig with the cotrol pael ad deactivates whe commuicatio starts agai Com 3 Fault This output tpe activates whe whatever is coected to Com Port 3 stops commuicatig with the cotrol pael ad deactivates whe commuicatio starts agai Com 1 No Sigal This output tpe activates whe whatever is coected to Com Port 1 loses its sigal ad deactivates whe its sigal is regaied Com 2 No Sigal This output tpe activates whe whatever is coected to Com Port 2 loses its sigal ad deactivates whe its sigal is regaied Com 3 No Sigal This output tpe activates whe whatever is coected to Com Port 3 loses its sigal ad deactivates whe its sigal is regaied Coms Fault This output tpe activates wheever a tpe of commuicatio fault occurs i.e. No Sigal, Com Port Fault, lie fault etc. ad deactivates whe commuicatio starts agai Radio Jammig This output tpe activates wheever the wireless radio receiver detects a jammig sigal ad deactivates whe the jammig sigal is removed Radio RX Tamper This output tpe activates whe the wireless radio receiver lid is removed, causig a Tamper alarm o the sstem, ad deactivates whe the Tamper alarm is reset Detector Test This output tpe is activated via Witex to iitiate a diagostics check o a PD6662: 2004/EN Grade 3 detector ad deactivates after 10 secods ATS Remote Test This output tpe coforms to the BSIA Form 175 Specificatio. Whe a Lie Fault is ot preset it ca be activated remotel b Witex, or b usig the Test Call Timer or Start Test Call optio o the cotrol pael to iitiate a test o ATE equipmet that have a ATS test iput. NOTE: Ol the RedCare Lie Fault ad Cotrol pael Lie Fault iputs ca be used with the output tpe No ATS Available This output tpe activates whe o Alarm Trasmissio paths are available ad deactivates whe the fault is cleared CIE Fault This output tpe activates whe a fault occurs o the CIE ad deactivates whe the fault is cleared PSU Fuse Blow This output tpe activates whe the Auxiliar iput tpe PSU Moitor detects a 12V failure ad deactivates whe the fault is reset PSU Batter Flt This output tpe activates whe the Auxiliar iput tpe PSU Moitor detects a batter fault ad deactivates whe the fault is reset. 53 WD Test Active This output is activated via remote maiteace software to iitiate a diagostics check o a exteral souder with remote test capabilit ad will deactivate after 1 miute. 78 INS176-9

79 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Output Group - Area A umber of areas ca be assiged to each output tpe. Select a output tpe from the followig optios: 00 - Alarm This output tpe activates whe a tpe of Itruder alarm occurs i the selected area, ad deactivates whe the Itruder alarm is reset Guard Alarm This output tpe activates whe a zoe programmed as Guard causes a Itruder alarm i the selected area ad deactivates whe the alarm is reset Guard Access Alarm This output tpe activates whe a zoe programmed as Guard Access causes a Itruder alarm i the selected area ad deactivates whe the alarm is reset Etr Alarm This output tpe activates whe a zoe programmed as Etr/Exit 1 or 2 causes a Itruder alarm i the selected area ad deactivates whe the alarm is reset Cofirmed Alarm If a area is alread i alarm, this output tpe activates whe a differet zoe (ot o the etr route) is activated i the selected area ad deactivates at the ed of the Cofirmatio time, whe a code is etered withi the Abort time or whe the alarm is reset Hr Audible This output tpe activates whe a zoe programmed as 24Hr Audible causes a Iteral alarm or Itruder alarm i the selected area ad deactivates whe the alarm is reset Hr Silet This output tpe activates whe a zoe programmed as 24Hr Silet causes a silet alarm or Itruder alarm i the selected area ad deactivates whe the alarm is reset Hr Gas This output tpe activates whe a zoe programmed as 24Hr Gas causes a Silet alarm or Itruder alarm i the selected area ad deactivates whe the alarm is reset PA Alarm This output tpe activates whe a tpe of PA alarm i.e. PA audible, PA silet or Duress causes a PA alarm i the selected area ad deactivates whe the alarm is reset PA Silet This output tpe activates whe a zoe programmed as PA Silet or a kepad PA (1 & 3) causes a silet PA alarm i the selected area ad deactivates whe the alarm is reset Duress This output tpe activates whe a User code with the Duress attribute causes a silet PA alarm i the selected area ad deactivates whe the alarm is reset Fire Alarm This output tpe activates whe a zoe programmed as Fire or a kepad Fire (4 & 6) causes a Fire alarm i the selected area ad deactivates whe the alarm is reset Medical This output tpe activates whe a zoe programmed as Medical or a kepad Medical (7 & 9) causes a Medical alarm i the selected area ad deactivates whe the alarm is reset Auxiliar Alarm This output tpe activates whe a zoe programmed as Auxiliar causes a Silet alarm i the selected area ad deactivates whe the alarm is reset Tamper Alarm This output tpe activates whe a tpe of Tamper alarm occurs i the selected area ad deactivates whe the alarm is reset Alarm Abort If the selected area is i alarm, this output tpe activates whe a User code is etered to cacel the alarm i the selected area ad deactivates after 10 secods. Sstem Outputs 16 - Read This output tpe activates whe all zoes i the selected area are secure ad deactivates whe a zoe i the selected area is activated Etr Mode This output tpe activates whe the selected area is i the etr mode ad deactivates whe the area is ot i the etr mode d Etr Mode This output tpe activates whe the 2 d etr timer for the selected area starts ad deactivates whe the 2 d etr timer expires Exit Mode This output tpe activates whe the selected area is i the exit mode ad deactivates whe the area is ot i the exit mode Etr/Exit Mode This output tpe activates whe the selected area is i the etr or exit mode ad deactivates whe the area is o loger i the etr or exit mode Armed This output tpe activates whe the selected area is armed ad deactivates whe the selected area is disarmed Full Armed This output tpe activates whe the selected area is full armed ad deactivates whe the selected area is disarmed Part Armed This output tpe activates whe the selected area is part armed ad deactivates whe the selected area is disarmed Part Armig This output tpe activates whe the selected area is part armig ad deactivates whe the selected area arms Force Armable This output tpe activates whe the selected area has at least oe zoe with the Force Omit attribute, ad the area is able to be force armed. It will deactivate whe the area caot be force armed Force Armed This output tpe activates whe the selected area is forced to arm with zoes active, ad deactivates whe all zoes are reistated Arm Failed This output tpe activates whe the selected area fails to arm because a zoe is i fault, ad deactivates whe a valid User code is etered Bell SAB This output tpe activates whe a Exteral alarm occurs i the selected area, ad deactivates whe area is disarmed or the Bell Duratio timer expires Bell SCB This output tpe deactivates whe a Exteral alarm occurs i the selected area, ad activates whe area is disarmed or the Bell Duratio timer expires Strobe This output tpe activates whe a Exteral alarm (or Arm Fail) occurs i the selected area, ad deactivates whe area is disarmed (or a valid User code is etered) Detector Latch This output tpe activates for 5 secods whe the selected area is i the exit mode the activates agai whe the area arms ad deactivates whe a Itruder alarm occurs or the selected area is disarmed Detector Reset This output tpe is ormall active, ad deactivates for 5 secods whe the selected area is i the exit mode Walk Test Active This output tpe activates whe the Walk Test procedure is selected, ad deactivates whe the Walk Test procedure is cacelled Zoes Omitted This output tpe activates whe a zoe i the selected area with the Omit attribute, is omitted b the user, ad deactivates whe the zoe is reistated. INS

80 Sstem Outputs 35-24Hr Zoes Omit This output tpe activates whe a zoe programmed as 24Hr Audible or 24Hr Silet (with the Omit attribute) is omitted b the user, ad deactivates whe the zoe is reistated Reset Required This output tpe activates whe the selected area requires a reset followig a alarm, ad deactivates whe the alarm is reset Door Strike This output tpe activates for the 4 secods whe a User code with the Door Strike attribute is etered for the selected area Chime Mimic This output tpe activates for 2 secods whe a zoe i the selected area with the Chime attribute is activated Chime Eabled This output tpe activates whe Chime is eabled for the selected area, ad deactivates whe Chime is disabled for the selected area DK First Kock This output tpe activates whe a zoe i the selected area with the Double Kock attribute is activated for the first time, ad deactivates whe the zoe causes a alarm or the Double Kock Dela timer expires BP First Kock This output tpe activates whe a zoe i the selected area with the Beam Pair attribute is activated for the first time ad deactivates whe aother zoe with the Beam Pair attribute, causes a alarm or the Beam Pair Time expires O Test This output tpe activates whe a zoe i the selected area with the Test attribute is placed o test ad deactivates whe the Soak Test Time expires Test Fail This output tpe activates whe a zoe i the selected area with the Test attribute is placed o test (ad fails) ad deactivates whe a Egieer code is etered or the Soak Test Time expires Iteral Alarm This output tpe activates whe a Iteral alarm occurs i the selected area, ad deactivates whe the alarm is cacelled Auto Armig This output tpe activates whe the selected area Auto Arms, ad deactivates whe the selected area is disarmed Time Armig This output tpe activates for 5 miutes prior to the selected area beig armed usig the Cotrol Timers st Code Etered This output tpe activates for 30 secods whe a User code with the Dual Code attribute is etered for the selected area d Code Etered This output tpe activates for 30 secods whe two User codes with the Dual Code attribute are etered for the selected area Area Secured This output tpe activates wheever a Securit Ke zoe tpe is used to lock kepads out ad deactivates whe the kepads are ulocked agai Part Armed 1 This output tpe activates whe a Part Arm 1 is selected for the selected area ad deactivates whe part arm 1 is disarmed Part Armed 2 This output tpe activates whe a Part Arm 2 is selected for the selected area ad deactivates whe part arm 2 is disarmed Part Armed 3 This output tpe activates whe a Part Arm 3 is selected for the selected area ad deactivates whe part arm 3 is disarmed Custom Alarm This output tpe activates whe a Custom zoe tpe causes a alarm i the selected area ad deactivates whe a valid user code is etered. Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 54 - Zoe Warig This output tpe activates whe Custom zoe tpe i the selected area with the Warig Req attribute (see page 52 for details) is activated for the duratio of the Warig Dela timer (see page 63 for details) ad deactivates whe the zoe activit is cleared Arm Fail Warig This output tpe activates whe the selected area fails to arm after a period of time (cotrolled b the area exit time) whe usig Etr/Exit or Exit Term. armig ad deactivates whe the area arms Forced Etr This output tpe activates for the duratio of the Forced Etr timer (see page 63 for details) whe a Guard or Custom zoe with the Guard attribute is activated (see page 51 for details), Zoes Locked Out This output tpe activates whe a zoe is locked out followig a Itruder Alarm activatio ad deactivates whe all zoes are clear ad reistated All Areas Armed This output tpe activates whe all of the selected areas are armed ad deactivates whe a oe of those areas is disarmed Time Arm Disabled This output tpe activates whe the timed armig procedure is disabled (see page 52 for details) ad deactivates whe timed armig is reistated Armed/Alarm This output tpe activates whe the selected area is armed ad deactivates whe the selected area is disarmed This output tpe also pulses whe a Itruder alarm occurs i the selected area, ad deactivates whe the selected area is disarmed Itruder Alarm This output tpe activates whe a Itruder alarm occurs, ad deactivates whe the Itruder alarm is cacelled. Tamper alarms will ot activate this output 62 - Speaker Mimic This output tpe activates wheever the iteral speaker output is o, ad deactivates whe the speaker output is off Full Armed/Exit This output tpe activates whe the selected area is i the full arm exit mode ad the arms ad deactivates whe the area is disarmed Detector Fault This output tpe activates whe a detector fault occurs ad deactivates whe the fault is reset Detector Masked This output tpe activates whe a detector mask occurs ad deactivates whe the mask is reset Fault Preset This output tpe activates whe a geeral fault occurs i.e. Lie Fault, AC Mais Fail, Detector Fault etc. ad deactivates whe the fault is cleared LED Cotrol This output tpe is alwas activate ad deactivates whe a User or Egieers code is etered to gai access to a meu. The output activates agai 30 secods after the user/egieer exits the meu. This output tpe is for use with detectors that require 0V applied to disable their LED s Full Arm Etr This output tpe activates whe the etr mode is started ad deactivates whe the etr mode fiishes wheever the sstem i Full Armed. 69 Fire Souder This output tpe activates whe a Zoe programmed as Fire, or a Kepad Fire (4&6) causes a Fire Alarm i the selected area ad deactivates whe the alarm is reset. 80 INS176-9

81 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 70 Cofirmed PA If a area is i PA alarm this output tpe activates whe oe of the followig happes. aother PA zoe is activated A tamper is detected from a differet device A secod sigal from a multi actio PA A global tamper withi the timer period 71 Cofirmed Itruder If a area is i Alarm, this output tpe activates whe a differet zoe (ot the etr route) is activated i the same area. This output tpe deactivates at the ed of the cofirmatio time whe a valid code is etered withi the Abort time, or whe the alarm is reset. Output Group - Zoe A zoe ca be assiged to this output tpe. Select a zoe umber.the select a output tpe from the followig optios: Mimic This output tpe activates whe the selected zoe is activated ad deactivates whe the zoe is secure. This output will work if the zoe is armed or disarmed. MimicArm This output tpe activates whe the selected zoe is activated ad deactivates whe the zoe is secured. This output will ol work if the zoe is armed. Alarm This output tpe activates whe the selected zoe causes a alarm ad deactivates whe the alarm is reset. This output will ol work if the zoe is armed. Tamper This output tpe activates whe the selected zoe causes a Tamper alarm ad deactivates whe the tamper is reset. This output will work if the zoe is armed or disarmed. MimicLat This output tpe activates whe the selected zoe is activated ad deactivates whe the ext time the zoe is activated. This output will work if the zoe is armed or disarmed. Omitted This output tpe activates whe the selected zoe is omitted ad deactivates whe the zoe is reistated. Output Group - User Code Etered A user ca be assiged to this output tpe. This output tpe activates for 5 secods whe the selected User code is etered. Output Group - Cotrol Timer Select a Cotrol Timer. These output tpes activate whe the respective cotrol timer turs o ad deactivate whe the timer turs off. Sstem Outputs These output tpes activate for the duratio of the Door Strike timer whe a valid User code (assiged to the same door) is etered ad deactivates whe the timer expires. These output tpes are used i cojuctio with the Door Cotrol User optio (see page 111 for details). Output Attributes Assigig a attribute to a output will alter how the output works. The followig attributes ca be assiged to a of the various tpes listed. Select attributes b pressig kes 1 to 8 (a letter o the displa meas the attribute is selected, a Dot o the displa meas the attribute is ot selected). U - User Test The output will activate whe a user performs a User test (see page 117 for details). I - Iverted The output is iverted (a output that applies 0V whe active will become a output that applies 12V whe active). L - Latchig Whe activated, the output will remai o util a valid User code is etered. 1 - Use Pulse Period 1 Whe activated, the output will remai o for the duratio of the Pulse Period 1 timer (see page 62 for details). 2 - Use Pulse Period 2 Whe activated, the output will remai o for the duratio of the Pulse Period 2 timer (see page 62 for details). 3 - Use Pulse Period 3 Whe activated, the output will remai o for the duratio of the Pulse Period 3 timer (see page 62 for details). C - Ol Active With Custom Output 1 Stage A The output will ol operate whilst Custom Output Stage A is O (see page Custom Outputs for details). R - Radom The output will activate radoml. A miimum ad maximum O time ca also be programmed (see page 62 for details). X-10 Outputs X-10 Outputs are outputs that ca be cofigured to operate devices that are coected to a X-10 cotroller. These outputs ca be assiged a house ad uit umber. To Program a output for X-10, proceed as follows: Program the output tpe to esure correct operatio whe the programmed coditio occurs i.e. a output programmed as Etr/Exit will activate whe the selected area is i the etr or exit mode ad deactivate whe the area is o loger i the etr or exit mode. Assig a attributes i.e. Pulsed 1 would cause the output to be timed for the duratio of the Pulse 1 timer. Assig a House ad Uit umber i.e. this is the phsical address of the X-10 Uit ad esures that the correct uit i the correct area operates whe the output coditio is met i.e the correct uit switches o ad off durig Etr/Exit. Output Group - PC Cotrol Select a PC Cotrol. These output tpes ca be activated ad deactivated usig a PC ruig the Witex UDL software. Output Group - Door Cotrol Select a Door Cotrol from 1,1 to 1,4 (48), 1,1 to 1,8 (88), 1,1 to 2,8 (168) 1,1 to 8-8 (640). INS

82 Sstem Outputs Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Custom Outputs Custom outputs are NOT phsical outputs the are Software outputs that ca be cofigured to operate uder certai coditios. Oce cofigured these outputs ca the be assiged to a phsical output (see sstem outputs ad 32-37, page 78 for details). Custom Output 1-4, Stage A Will activate whe switches 1 or 2 ad 3 ad 4 are active. Custom Output 1-4, Stage B Will activate whe switches 5 or 6 ad 7 ad 8 are active. Custom Output 1-4, Stage AB Will activate whe switches 1 or 2 ad 3 ad 4 are active OR switches 5 or 6 ad 7 ad 8 are active A 5 AB B Example Switch 1 is programmed as: Zoe 1 Mimic Switch 2 is programmed as: Zoe 2 Mimic Switch 3 is programmed as: Armed Switch 4 is programmed as: Never Active (ad iverted) Custom Output 1 Stage A will ol activate whe switches 1 OR 2 AND 3 AND 4 are closed. i.e. if ZONE 1 or ZONE 2 ACTIVATES whilst the sstem is ARMED (switch 4 is alwas closed). Assig up to 16 Characters of text to each uit to allow eas idetificatio whe the output eeds to be mauall triggered directl from the kepad usig the commad i.e. Etrace Light. Zoe Group Outputs Zoe Group Outputs will activate whe oe or more zoes o the cotrol pael are assiged to a Zoe Group. Zoe Group Mimic This output tpe will become active whe a zoe assiged to the group goes active or chages state. Zoe Group Armed This output tpe will become active whe a zoe assiged to the group goes active whe the area the zoes is assiged too is armed. 82 INS176-9

83 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual UDL/Digi Optios 5.7 UDL/Digi Optios Reset Digi MSN/Pre-Dial No. UDL/Digi Optios UDL/Digi Optios Reset Digi Press RESET to reset th e digimodem - a cofimatio toe will be he ard This optio should be used wheever a plug-o commuicator is plugged o or removed from the cotrol pael. UDL/Digi Optios UDL/Digi Optios Reset Digi 2 UDL/Digi Optios MSN/Pre-Dial No. Start Test Call UDL/Digi Optios UDL/Digi Optios Reset Digi 1 UDL/Digi Optios Start Test Call Do Test Call = 0 Call PC= 1,2 or 3 0 Com300 is Idle Wait Dial Toe Wait Dial Toe Diallig No. 1P Press 0 to sed a test call or 1, 2 or 3 to iitiate a upload to a remote computer ^ >123 Use kes 0-9 to eter umbers,? *44# ^ >123 O mit = *, C hime = # Part = 3 secod Pause Area = 10 Sec od Pause Whe a ComISDN is coected to a extesio of a ISDN lie with more tha 1 umber, the direct dial umber should be programmed i here, this esures that the ComISDN will ol aswer a call whe the direct dial umber is dialled. This umber ca be up to 24 digits. The Use MSN/Pre-Dial optio must also be eabled (see page 88 for details). Whe eterig the telephoe umber the followig extra kes ca be used: Diallig No. 1P Lookig 1st H/S Lookig 1st H/S Sedig Data Sedig Data Wait Clear Dela Wait Clear Dela Com300 is Idle N Whe a plug-o commuicator has bee fitted to the cotrol pael. This optio ca be used to sed a test call to the Alarm Receivig Cetre or to iitiate a remote Upload/Dowload call to oe of the programmed call-back umbers. INS

84 UDL & Digi Optios Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Program Digi S ta rt Select the required Alarm Receivig Cetre Set e.g. 2 = Set 2 UDL/Digi Optios UDL/Digi Optios Reset Digi 3 UDL/Digi Optios Program Digi ARC 1 Protocol: Disabled 2 ARC 2 Protocol: Disabled Press NO to select the protocol Use kes 0-4 to s elect a protoc ol or use the S C R O LL ke to s earch > ARC Disabled 2 Protocol: 2 ARC 2 Protocol: > Fast Format Primar No.: Pre s s NO to edit the Primar telephoe umber ^ >123 Us e k es 0-9 to e ter the telephoe umber O mit = *, C hime = # Part = 3 secod Pause Area = 10 Secod Pause? 9, ^ >123 Pre s s NO to edit the S ec odar telephoe umber Us e k es 0-9 to e ter the telephoe umber O mit = *, C hime = # Part = 3 secod Pause Area = 10 Secod Pause Secodar No.: ^ >123? 9, ^ >123 Accout Number: P res s NO to edit the ac cout umber or press AR E A to e dit the area accout umbers Us e k es 0-9 to e ter the acc out umber e.g = Accout 1234 ^ >123? Accout Number: 1234 Pre s s NO to edit the umber of diallig attempts E ter the umber of dia llig atte mpts e.g. 3 = 3 a tte mpts Diallig Attempts 00 Diallig Attempts > 00 3 Diallig Attempts > 03 Please refer to ext page 84 INS176-9

85 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual UDL & Digi Optios From previous page if Fast Format protocol is selected Reportig o:... Pre s s NO to edit the reportig chaels Use kes 1-8 to selec t the R eportig chaels e.g. 2 & 3 = chaels 2, 3 Reportig o: > Reportig o: > Restorig o:... Pre s s NO to edit the reportig chaels Restorig o: >... Use kes 1-8 to selec t the Restorig chaels e.g. 2 & 3 = chaels 2, 3 23 Restorig o: > Ope/close o:... Pre s s NO to edit the Ope/Close chaels Ope/close o: >... Use kes 1-8 to selec t the Ope/Close chaels e.g. 2 & 3 = chaels 2, 3 23 Ope/Close o: > Press NO to edit the reports optios Press NO to chage the reports optio Cofig: Use Area Acc > Use Area Acc >A B ack to the s tart INS

86 UDL & Digi Optios Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual From previous page if Cotact ID, S IA L evel II, EasC om Pager or S MS Messagig protocols are selected Press NO to edit the report areas Use kes 1-8 to select the R eport areas e.g. 1 = area A for 640 s ee below Report Areas :... Report Areas : >... < 1 Report Areas : > A... < Press NO to edit the reports optios Use the SCROLL ke to select the required R eports optio Press NO to chage the reports optio Reports: >. Priorit.... Alm... Normal.>... Alarm U.... Normal Alarm.>A Press NO to edit the reports optios Use the SCROLL ke to select the required R eports optio Press NO to chage the reports optio Cofig: Use Area Acc Use SIA I > U.> Use SIA I.>S..... B ack to the s tart Report Areas : 1 ABCDEFGHIJKLMNOP Report Areas : 1 ABCDEFGH< JKLMNOP CP / Use the C hime & Part kes to sc roll betwe e Are a G roups 1, 2, 3 & 4 A Report Areas : 1 ABCDEFGH>JKLMNOP U se the Area ke to select either A-H or I-P a rea s. Use the umeric buttos 1-8 to toggle the require d are as o or off 86 INS176-9

87 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual The plug-o commuicator ca be programmed to dial up to 3 sets of Alarm Receivig Cetre (ARC) iformatio. Each Set cosists of the followig optios: Protocol This is the reportig protocol that is used to commuicate with the Alarm Receivig Cetre. The followig 4 protocols are supported: Fast Format: The pael will report usig Fast Format. If this optio is selected the Reportig Chaels must be programmed (see below) Cotact ID: The pael will report usig Cotact ID. If this optio is selected, the Reportig Areas must be programmed (see below) SIA Level II: The pael will report usig SIA Level II EasCom Pager: The pael will report to a EasCom tpe pager SMS Messagig: The pael will sed Short Message Service (SMS) text messages to a mobile phoe Primar Telephoe Number This is the first telephoe umber that the commuicator will dial for the Alarm Receivig Cetre or the first mobile telephoe umber to sed SMS to. Each telephoe umber ca be up to 24 digits. Secodar Telephoe Number This is the secod telephoe umber that the commuicator will dial for the Alarm Receivig Cetre or the secod mobile telephoe umber to sed SMS to. Each telephoe umber ca be up to 24 digits. Accout Number This is the accout umber that will be reported to the Alarm Receivig Cetre. Each accout umber ca be up to 6 digits. Each area ca also have its ow accout umber (see page 88 & 81 for details). Diallig Attempts This is the umber of times the commuicator will tr to dial the Alarm Receivig Cetre or Pager telephoe umber. The umber of diallig attempts is limited to 9. If this value is set to 0, the commuicator will ever dial out. The followig optio is ol displaed if the Fast Format protocol is selected Reportig o This optio defies which chaels report to the selected Alarm Receivig Cetre. Restorig o This optio defies which chaels report a restore to the selected Alarm Receivig Cetre. Ope/Close o This optio defies which chaels report Ope/Close to the selected Alarm Receivig Cetre. The followig optio is ol displaed if Cotact ID or SIA Level II protocols are selected Reportig Areas This optio defies which areas report evets to the selected Alarm Receivig Cetre. UDL & Digi Optios The followig optio is ol displaed if Cotact ID, SIA Level II or EasCom Pager protocols are selected Reports This optio defies which evets report to the Alarm Receivig Cetre whe usig Cotact ID or SIA Level II. P - Priorit Alarm ad Cacel Evets The sstem will report Priorit alarm ad cacel evets to the selected Alarm Receivig Cetre. A - Normal Alarm ad Cacel Evets The sstem will report alarm ad cacel evets to the selected Alarm Receivig Cetre. O - Ope ad Close Evets The sstem will report ope ad close evets to the selected Alarm Receivig Cetre. B - Omit ad Reistate Evets The sstem will report omit ad reistate evets to the selected Alarm Receivig Cetre. M - Maiteace Alarm Evets The sstem will report maiteace alarm evets to the selected Alarm Receivig Cetre. T - Tamper Alarm Evets The sstem will report tamper alarm evets to the selected Alarm Receivig Cetre. C - Test Call Evets The sstem will report test call evets to the selected Alarm Receivig Cetre. R - Restore Evets The sstem will report restore evets to the selected Alarm Receivig Cetre. The followig optio is ol displaed if Fast Format Cotact ID or SIA Level II protocols are selected Cofig. This optio defies which secodar optios are eabled. A - Area Accout Evets are reported to the Alarm Receivig Cetre usig the area accout umbers (see page 88 for details). S - SIA Level I / UCP Evets are reported to the Alarm Receivig Cetre usig SIA Level I or or to a SMS Messagig Server usig UCP. R - Eable Radio-Pad The sstem will use the Paket radio-pad to report evets to the selected Alarm Receivig Cetre. G - Eable GSM Module The sstem will use the GSM Module to report evets to the selected Alarm Receivig Cetre. A - AV Module The AV Module will dial the Alarm Receivig Cetre. F - Use GSM First The GSM module is the primar path whe this is eabled I - Coect Via IP The sstem will use the IP Module to report evets to the selected Alarm Receivig Cetre. T - Sed SIA Text Text is set to the Alarm Receivig Cetre whe usig SIA II (this makes the protocol SIA III) INS

88 UDL & Digi Optios Digi Optios Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Area Accouts 24/48/88/168 UDL/Digi Optios UDL/Digi Optios Reset Digi 4 UDL/Digi Optios Digi Optios UDL/Digi Optios UDL/Digi Optios Reset Digi 6 UDL/Digi Optios Area Accouts Digi Optios Press NO to edit the Digi optio Area A Accout: Us e kes 1-8 to se le ct a area or use the S C RO LL k e to sea rch e.g. 2 = Area B. Digi is Eabled > U Use kes 1-8 to selec t a optio or use the SCR OLL ke to searc h Area B Accout: Pre s s NO to edit the acc out umber Blid Diallig...>... Blid Diallig...>B.. Press NO to select/deselect the optio ^ >123? Area B Accout: Us e k es 0-9 to e ter the acc out umber e.g = Accout 1234 There are 6 optios that cotrol how the plug-o commuicator works. Select optios b pressig kes 1 to 8 (a letter o the displa meas the optio is selected, a Dot o the displa meas the optio is ot selected). E - Digi is Eabled The plug-o commuicator will report all sstem evets to the Alarm Receivig Cetre. P - Pulse Diallig The plug-o commuicator will alwas dial telephoe umbers usig pulse diallig. 3 - Pulse After 3 The plug-o commuicator will alwas dial telephoe umbers usig toe diallig. However, if the Commuicator fails to dial the umber three times i a row, it will revert to pulse diallig for the remaiig attempts. B - Blid Diallig The plug-o commuicator will ot look for a dial toe before diallig a telephoe umber. U - Use MSN/Pre-Dial The ComISDN will ol aswer a call whe the programmed MSN/Pre-Dial telephoe umber is dialled. A - Dial All Numbers If the commuicator is ackowledged b the first ARC, it will cotiue to dial a other programmed ARC. This is ormall used whe a secod or third ARC is programmed with SMS Messagig. Whe usig Fast Format, Cotact ID or SIA, each area ca have its ow accout umber to idetif evets. Accout Numbers A to H (I to P) This is the accout umber that will be reported to the Alarm Receivig Cetre. Each accout umber ca be up to 6 digits. I order for the cotrol pael to use the area accout umbers, the area accout Cofig. optio must be eabled (see page 87 for details). 88 INS176-9

89 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual UDL & Digi Optios Area Accouts 640 UDL/Digi Optios UDL/Digi Optios Reset Digi 6 UDL/Digi Optios Area Accouts Area 1A Accout: Area 1B Accout: Use the SCR OLL ke to search for areas. Pre s s NO to edit the acc out umber ^ >123? Us e k es 0-9 to e ter the acc out umber e.g = Accout 1234 Area 1B Accout: Whe usig Fast Format, Cotact ID or SIA, each area ca have its ow accout umber to idetif evets. Accout Numbers A to H (I to P) This is the accout umber that will be reported to the Alarm Receivig Cetre. Each accout umber ca be up to 6 digits. I order for the cotrol pael to use the area accout umbers, the area accout Cofig. optio must be eabled (see page 87 for details). INS

90 UDL & Digi Optios Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual UDL Optios UDL/Digi Optios UDL/Digi Optios Reset Digi 5 UDL/Digi Optios UDL Optios Call Back No. 1 P res s NO to edit the C all B ack umber Us e k es 0-9 to e ter the telephoe umber O mit = *, C hime = # Part = 3 secod Pause Area = 10 Secod Pause ^ >123? 9, ^ >123 Call Back No. 2 Call Back No. 3 Follow Call B ac k No. 1 Istructios Follow Call B ac k No. 1 Istructios UDL Password is: P res s NO to edit the UDL Password ^Edit Text >ABC U s e ke s 0-9 to pro g ram te xt the sa me wa tha t a mobile phoe work s? ABC123 Edit^Text >123 UDL Optios. M D... Press NO to edit the UDL Optios Use kes 1-8 to selec t a optio or use the SCR OL L ke to searc h Press NO to select/deselect the optio DL Atteded Call Defeat ON >. M D... U. M>D... Call Defeat O. M>.... Rigs required: 000 Press NO to edit the R igs required Rigs required: > 000 E ter the umber of rigs required e.g. 3 = 6 rigs 6 Rigs required: > 006 Diallig Attempts 00 Press NO to edit the Diallig Attempts Diallig Attempts > 00 E ter the umber of dia llig atte mpts e. g. 3 = 3 a tte mpts 3 Diallig Attempts > INS176-9

91 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual The sstem has the followig UDL dowload optios: Dowload Call Back Number 1 This is the telephoe umber that is dialled b the modem whe Callback Number 1 is requested b the remote UDL computer. This telephoe umber ca be up to 24 digits. Dowload Call Back Number 2 This is the telephoe umber that is dialled b the modem whe Callback Number 2 is requested b the remote UDL computer. This telephoe umber ca be up to 24 digits. Dowload Call Back Number 3 This is the telephoe umber that is dialled b the modem whe Callback Number 3 is requested b the remote UDL computer. This telephoe umber ca be up to 24 digits. UDL Password is: Whe the remote dowloadig computer dials ito the sstem, the cotrol pael compares the UDL password set b the computer with UDL password stored i the cotrol pael. If the passwords match, access to the cotrol pael is grated, if the do t match, access is deied. If more tha three attempts at reportig are made with a wrog password, the modem will lock out for 4 hours or util a Master User code is etered. The UDL password programmed i this optio must also be programmed i the customer accout o the remote dowloadig computer. This password ca be up to 16 characters (umbers ad letters). If o UDL Password has bee programmed, access to the cotrol pael ca be gaied b usig the egieers code as the UDL Password. UDL Optios There are 6 UDL optios that affect how ad whe access to the cotrol pael via the Witex UDL software is allowed. Select optios b pressig kes 1 to 6 (a letter o the displa meas the optio is selected, a Dot o the displa meas the optio is ot selected). The followig UDL optios are available: A - DL Atteded The sstem will ot allow the remote dowloadig computer access without user authorisatio first. M - Ma Call-Back The sstem will ot use the automatic call back feature. The user must istruct the pael to call back the remote dowloadig computer. The Auto Call-Back feature operates as follows: D - Call Defeat The modem will aswer icomig calls as follows: UDL & Digi Optios The modem must detect oe or more rigs ad the umber of rigs must NOT exceed the value set up i Rigs Required Whe the rigig stops, the pael will start a 30 secod dela timer If the modem detects rigig before the timer expires it will aswer the call immediatel L - Armed DL Limited The pael will ot allow dowload access whe the sstem is armed (also see below). A - A Area Armed The pael will ot allow dowload access whe a areas are armed. K - Olie RKP = Off The cotrol pael caot be accessed usig the O-lie kepad feature of the Witex UDL software. Rigs Required This couter cotrols the umber of rigs the modem eeds to see before it will aswer the call (Default = 003). UDL Dial Attempt If a Call-Back is started, this optio cotrols how ma times the modem will tr to call the remote dowloadig computer before givig up (Default = 003). Eter the umber of diallig attempts. This umber is limited to 9. If this value is set to 0, the commuicator will ever dial out. This ol affects the modem for dowload access ad does ot affect the operatio of the commuicator i a wa. The remote dowloadig computer calls the cotrol pael ad establishes a coectio The UDL password is verified ad the remote dowloadig computer istructs the pael to call it back usig oe of the 3 call back umbers The pael hags up ad dials the requested umber ad reestablishes the coectio with the remote dowloadig computer INS

92 UDL & Digi Optios Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Setup Modules UDL/Digi Optios UDL/Digi Optios Reset Digi 7 UDL/Digi Optios Radio/SMS Optio Setup Radio-Pad? U Setup AV Module? U Setup IP Data? U Press YES to setup the Radio-Pad N Press YES to setup the Radio-Pad Pad ARC 1 Pri No Use kes 0-9 to selec t a optio or use the SCR OL L ke to searc h Pres s NO to e dit the AR C Primar R adio-pa d telephoe umber Us e k es 0-9 to e ter the telephoe umber Omit = *, Chime = # Part = 3 secod Pause Area = 10 Secod Pause Pad ARC 3 Pri No U ^ >123? Use kes 0-9 to selec t a optio or use the SCR OL L ke to searc h P ress NO to eter the umber of diallig attempts E ter the umber of dia llig atte mpts e.g. 5 = 5 a tte mpts AV No.1> AV Dial Attempts AV Dial Attempts U 03 > 03 5 N Press YES to setup the ComIP Module N Press YES to setup the IRIS Module ComIP Adress P res s No to edit the Access Poit Name Use kes 0-5 to selec t a optio or use the SCR OL L ke to searc h U Pollig Address P res s No to edit the User N ame Press NO to edit the optio ^ >123 P res s No to edit the User Password Use kes 0-9 to eter text? 123^ > ^ > ^ >123 Setup GPRS Data? Chiro IRIS U SMS Cetre Pri. U SMS Cetre Sec. U Modem Setup Stg. U Modem Speed: 2400 U N P res s NO to edit the SMS Cetre Primar telephoe umber P res s NO to edit the SMS Cetre Secodar telephoe umber ^ >123 Us e k es 0-9 to e ter the telephoe umber Omit = *, Chime = # Part = 3 secod Pause Area = 10 Secod Pause Us e k es 0-9 to e ter the telephoe umber Omit = *, Chime = # Part = 3 secod Pause Area = 10 Secod Pause ^ >123? Press NO to edit the Modem setup strig ^ >123? Pres s NO to cha ge the Modem speed Access Pt Name Modem Speed: > 4800? U s e ke s 0-9 to pro g ram te xt th e same wa that a mobile phoe works Us e the S C RO LL k e to select the required speed U User Name ^ > ^ >123 +CHSN=3,0,0,0 ^123 Modem Speed: > 9600 Password Pre ss R E S E T to reset Com 1 Pre ss R E S E T to reset Com 2 The followig 6 optios will ol be s e e is a R adio-pad or G SM Module is fitted Pad Serial No.: U Pad NUA: U Last Call From: aaaaaaa U FSS:016 (>=03) RSS:089 (>=50) U CRC:000 (<=10) BER:003 (<=10) U Sigal: -85 dbm GSM BER:00 (<4) U U Com1 Com2 92 INS176-9

93 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual The followig optios are used whe a Paket Radio-Pad is coected to the cotrol pael i order to achieve DUAL SIGNALLING to a Alarm Receivig Cetre, whe a MODEM (Exteral PC or Com2400) is used to coect to the cotrol pael or sed SMS messages to mobile phoes, whe a AV Module is coected to the cotrol pael i order to achieve AUDIO VERIFICATION to a Alarm Receivig Cetre or whe a TCP/IP Module is coected for commuicatios over a Broadbad/ADSL/DSL Lie. Setup Radio-Pad Pad ARC 1 Pri No This is the first umber that is used b the Radio-Pad for reportig evets to ARC 1. Pad ARC 1 Sec No This is the secod umber that is used b the Radio-Pad for reportig evets to ARC 1. Pad ARC 1 Prefix This umber will prefix the accout umber for ARC 1. Pad ARC 2 Pri No This is the first umber that is used b the Radio-Pad for reportig evets to ARC 2. Pad ARC 2 Sec No This is the secod umber that is used b the Radio-Pad for reportig evets to ARC 2. Pad ARC 2 Prefix This umber will prefix the accout umber for ARC 2. Pad ARC 3 Pri No This is the first umber that is used b the Radio-Pad for reportig evets to ARC 3. Pad ARC 3 Sec No This is the secod umber that is used b the Radio-Pad for reportig evets to ARC 3. Pad ARC 3 Prefix This umber will prefix the accout umber for ARC 3. Radio-Pad Attempts This is the umber of times the Radio-Pad will tr to dial the Alarm Receivig Cetre telephoe umber before givig up. The umber of diallig attempts is limited to 9. If this value is set to 0, the Radio-Pad will ever dial out. Setup AV Module AV No. 1> This is the first umber that is dialled b the AV Module. AV No. 3> This is the secod umber that is dialled b the AV Module. AV No. 3> This is the third umber that is dialled b the AV Module. AV Dial Attempts This is how ma times the AV Module will attempt to dial before givig up. The umber of diallig attempts is limited to 9. If this value is set to 0, the AV Module will ever dial out. AV Re-Dial Dela This is the amout of dela that the AV Module uses betwee rediallig telephoe umbers. Setup IP Module ComIP Address This is the IP Address of the IP Module. ComIP Port This is the Port umber of the IP Module. UDL & Digi Optios ComIP Gatewa This is the Gatewa IP Address that the IP Module commuicates through. ComIP Mask This is the Subet Mask umber for the IP Module. Pollig/SMG Address This is the IP address of a dedicated Pollig or SMG Server that the IP Module might eed to coect to. Name/SMG Port This is a descriptive ame for the IP Module or SMG Port ad might be used for autheticatio purposes. Chiro Iris GPRS Data Access Pt Name This is the GPRS Access poit Name provided b Chiro User Name This is the APN User Name provided b Chiro Password This is the APN password provided b Chiro. SMS Cetres SMS Cetre Pri. This is the first SMS cetre telephoe umber that is used b for sedig SMS to mobile phoes. (Default = ). SMS Cetre Sec. This is the secod SMS cetre telephoe umber that is used b for sedig SMS to mobile phoes. (Default = ) Modem Modem Setup Stg. If a stadard PC modem is coected to Com1 or Com2, it ma require a cofiguratio strig to make it work properl (please refer to istructio maual of modem beig used for details of required AT commads). The Setup strig is programmed the same wa that TEXT would be programmed ad has a maximum legth of 16 characters. The setup strig does NOT require AT to be etered at the begiig as this is doe automaticall. Modem Speed This optio allows the speed of a stadard PC modem coected to Com1 or Com2 to be adjusted. Radio-Pad Ifo Pad Serial No. This scree displas the Serial umber of the Radio-Pad that is coected. Pad NUA This scree displas the NUA umber of the Radio-Pad that is coected. Last Call From This scree displas the NUA umber of the last Radio-Pad that commuicated with the Radio-Pad that is coected to the cotrol pael. FSS:??? (>=004), Forward Sigal Stregth RSS:??? (>=050), Reverse Sigal Stregth This scree displas the Radio-Pad Forward (FSS) ad Reverse (RSS) Sigal Stregth of the Radio-Pad that is coected to the cotrol pael. The FSS value should be greater tha or equal to 4 ad the RSS value should be greater tha or equal to 50. INS

94 UDL & Digi Optios CRC:??? (<=009), Cclic Redudac Check BER:??? (<=009), Bit Error Rate This scree displas the Cclic Redudac Check (CRC) ad Bit Rate Error (BER) of the Radio-Pad that is coected to the cotrol pael. The CRC ad BER values should be less tha 10. GSM Ifo Sigal =??? dbm (<=080), GSM Sigal GSM BER:??? (<=004), GSM Bit Error Rate This scree displas the sigal stregth (GSM) ad Bit Rate Error (BER) of a GSM Module that is coected to the cotrol pael. The GSM value should be greater tha or equal to 80 ad the BER value should be less tha 9. Com1 Moitor Scree This scree allows ou to view the data activit of Com1. Press RESET to reset the device coected to this port. Com2 Moitor Scree This scree allows ou to view the data activit of Com2. Press RESET to reset the device coected to this port. Com Port Setup UDL/Digi Optios UDL/Digi Optios Reset Digi 8 UDL/Digi Optios Com Port Setup Oboard Digicom Com300 Module Com Port 1 No Module Fitted Com Port 1 No Module Fitte< 7 Com Port 1 GSM Module < Use the S CROLL ke to s e le ct the required Com Port Pre s s NO to edit the C om Port Use kes 0-8 to selec t a device or use the S C R OL L ke to s e arc h e.g. 7 = G S M Module The cotrol pael must be programmed with the tpe of device that are coected to each of its coms ports. Oboard Digicom, Com Port 1 ad 2 The followig devices are available for fittig to the various ports: Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 0: No Module Fitted - No Devices/PC-Com/ USB-Com 1: Com300 - Com300 Commuicator. 2: Com Com2400 Commuicator. 3: ComISDN - ComISDN Commuicator. 4: ComIP - ComIP TCP/IP Commuicatio Module. 5: Modem Uit - Stadard Serial PC Modem. 6: Radio Pad - Paket RP9 Radio-Pad. 7: GSM Module - GSM Module/Mobile Phoe. 8: Crestro Sstem - Crestro Home Automatio Sstem. 9: SIP - Serial IP Protocol. 10: RadioPlus - Serial Wireless Receiver. 11: Iovoics Radio - Iovoics Serial Wireless Receiver. 12: WebWaOe/Emizo - WebWaOe/Emizo UDP Module. 13: X-10 Cotrol - X-10 Home Automatio Module. 14: IRIS IP - Chiro IRIS Serial TCP/IP Module. Oboard Digicom This optio determies what tpe of device is coected to the plugo digmodem coector o the top right had corer of the cotrol pael. (Default = Com300). The followig devices are available from the above list: 0 / 1 / 2 / 3 Com1 This optio determies what tpe of device is coected to the Com1 coector o the left had side of the cotrol pael. (Default = No Module Fitted). The followig devices are available from the above list: 0 / 2 / 3 / 4 / 5 / 7 / 8 / 9 / 10 / 12 / 13 / 14 If a of the above devices are coected to the cotrol pael o Com1 ad a PC eeds to be coected (for uploadig/dowloadig) the device must be discoected from Com 1 ad the Factor Default butto pressed for 3 secods to allow the PC to talk to the cotrol pael. If the PC is ot coected to the cotrol pael (or is removed) the Com port will automaticall revert back to ormal operatio after 1 miute. Com2 This optio determies what tpe of device is coected to the Com2 coector o the left had side of the cotrol pael. (Default = No Module Fitted). The followig devices are available from the above list: 0 / 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 Com3* This optio determies what tpe of device is coected to the Com3 coector o the left had side of the cotrol pael. (Default = No Module Fitted). The followig devices are available from the above list: 0 / 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 *640 ol Expasio Port This optio determies what tpe of device is coected to the Expasio Port coector (Default = No Module Fitted). Available Device Tpes: 0: No Module Fitted - No Devices 1: AV Module - Audio Verificatio Module 2: id Module - 60IXD id Module 3: X10 Module - X10 Cotroller 4:Memor Module Memor Module (24/48/88/168 ol) Selectig memor module whe oe is fitted will prevet evets beig recorded to the log. 94 INS176-9

95 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual DualCom Iside (48 Ol) Aerial Sitig ALWAYS do a site surve to fid a area of strog sigal before istallatio. Istallig a Com GSM with a weak sigal is bad istallatio practice. The aerial should be mouted verticall at the poit of strogest sigal. This is usuall the highest poit i the buildig (ofte the loft area). Avoid istallig the aerial directl uder metal roofs or withi metal skied buildigs because this will reduce the sigal stregth ad ma ihibit operatio completel. If this is uavoidable, the strogest sigal will be foud awa from the metal roof or close to large exteral widows or sklights. Avoid istallig the aerial close (2 metres) to cable rus, ductig, structural metalwork, metal pipes, water taks ad electroic equipmet, e.g. photocopiers, fax machies etc. These ca have similar effects to metal roofs. Reliable operatio is ulikel with a low sigal stregth. If the displa shows that the sigal stregth is 40% or lower, ou should improve the sigal stregth. This ma be achieved b repositioig the aerial. The GPRS aerial lead should ot be cut, therefore repositioig the aerial ma require that the Com GSM is also repositioed. The DualCom CS2366 Radio Test Set is ideal for surveig a site. This hadheld uit ca check the availabilit, sigal stregth ad iterferece status of all surroudig Base Statios. I additio, it will idetif the best locatio for a DualCom GPRS aerial withi the buildig, help to avoid sources of iterferece ad ca cofirm the availabilit of a GPRS service at the proposed site. Where a Nokia Net Mo phoe is available ad a Vodafoe SIM Card is fitted, it ma be used i the same maer as the CS2366 Radio Test Set. Alterativel, a Vodafoe mobile phoe ma be used to locate the poit of strogest sigal. The sigal stregth idicator is ormall a bar or lie at the side of the displa o the mobile telephoe. Note: The mobile phoe MUST use the Vodafoe etwork. A mobile phoe that uses a differet radio etwork will NOT show the correct sigal stregth. This mobile phoe method caot provide iformatio o the availabilit, sigal stregth ad iterferece status of all radio Base Statios i the surroudig area. Use of the CS2366 Radio Test Set is recommeded. Whe ou have idetified the poit of the strogest sigal, make a ote of this poit ad use it whe istallig the Com GSM aerial. Remember: It is alwas easier to fid the poit of strogest sigal before the equipmet is fitted to a wall. Movig aerials, cables, trukig etc. after istallatio is wasted time ad effort. Iitial Setup UDL & Digi Optios Please follow the istructios i INS176 to istall the equipmet ad iitiate the power up sequece. Whe applig power for the first time, the factor default settigs must be loaded. DualCom Iside caot be setup through Witex, so please follow the diagrams ad istructios to setup DualCom Iside. The process for eablig DualCom Iside is as follows:- 1. Istall Equipmet 2. Plug Com2400 oto cotrol pael PCB 3. Plug Com GSM oto Com port 1 a. Set optio switches 1 & 2 to ON ad 3 & 4 to OFF 4. Eter egieers mode o kepad 5. Select UDL/Digi Optios 6. Com Port Setup 7. Select Com2400 as the Digicom 8. Select ComIP for Com port 1 9. Eable DualCom Iside 10. Choose our ARC 11. Eter our Gemii Accout umber 12. Eter our PSTN umber 13. Test the equipmet The flow diagram o the followig page shows the procedure to eable ad test DualCom Iside. UDL/Digi Optios UDL/Digi Optios Reset Digi 8 UDL/Digi Optios Com Port Setup Oboard Digicom Nothig Fitted 2 Oboard Digicom Com 2400 Module 2 Com Port 1 Nothig Fitted 4 Com Port 1 ComIP Module N 9 UDL/Digi Optios DualCom Iside 1 DualCom Iside Eabled Sigal Stregth CSQ:40% BER:0% SIM ICCID???????????????????? ARC 1st Cout Mo U se the U ke to sele ct our ARC If the AR C ou u se is ot listed g o to Us er C o de a d e te r the code ou h ave be e give Gemii Accout?????? E ter our G emii Radio Accout Number PSTN Accout???? E ter ou r P S TN Acc ou t Nu mbe r Auto Set Up No Do ot use Auto S etup util S igal S tregth shows CS Q is > 4 0% & B E R is 0% if the values are icorre ct repositio the atea 1 The sste m will ow dowload th e c o figura tio file s from the C S L se rvers, DO NOT press this optio m ore tha oc e. Test Calls No 1 T he s stem wi ll o w tes t all e able d com muicatio paths ad report PAS S or FAIL for ea ch N N INS

96 UDL & Digi Optios EMIZON 21 TCD Itroductio The EMIZON 21 TCD is compatible with all Premier Elite Cotrol Paels. PCB Laout PSTN Coectio to phoe or pael Primar path LED Power LED TCD serial umber o label Mode Butto Set Butto 1 S/N: pi Iputs icl. BSIA Form 175 RS232 M S Power suppl iputs RS485 SIM Card Rela Outputs Secodar path LED Etheret activit LED Displa GPRS activit LED GPRS aerial Coectio Etheret port PC COM to TCD Coectio The Emizo 21 coects to the paels Via the PC-COM lead*. *Order Part Number JAA-0001 This lead coverts the TTL port to stadard RS232. You will eed to remove the 9 wa D-Tpe serial coector o the PC-COM adaptor ad coect the followig wires to the TCD RS232 termials as show i the table below. C ut Here PC-Com EMiZON 21 Black Wire Yellow Wire Blue Wire TCD GND TCD TX TCD RX Oce ou have coected the wires of the PC-COM to the TCD ou the eed to coect the Molex coector to Com1 or Com 2. Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Select Eable commuicator Pael IP Setup The cotrol pael commuicates to the ARC via the EMIZON TCD. The TCD s primar sigallig path is via a IP etwork; therefore the cotrol pael eed s a IP address so that it ca coect to a local etwork. Esure that the customer has filled i the Customer IT Surve Form provided b EMIZON. This will give ou the iformatio ou eed to set up the IP data o the cotrol. see page 93 (Setup IP Module) Coect the Etheret cable betwee the Etheret port o the TCD uit ad the Network router. Commissioig Now that the programmig for the EMIZON21 is complete ou eed to power up the TCD ad wait 15 secods (approx) ad check the followig Flickerig light o the Etheret path LED. Flashig gree light o the GPRS path LED. These idicate that the sigallig paths are available ad that the TCD is read to be commissioed. Now ou eed to call The ARC ( ) with the TCD serial umber that is prited o the label located o the frot cover, the ARC will the associate the TCD to this specific istallatio o their sstem ad activate it. If this is the first time this TCD is beig istalled, ou will eed to wait for the tl idicatio to appear o the displa ad the press ad hold the set butto for 4 secods. The TCD will cotact EMIZON service platform ad the displa will alterate betwee tl ad 01, the CA (completel Active). Alterate flashig decimal poits idicate ormal operatio followig a successful commissio. The GPRS ad Etheret LED s will tur gree to idicate that the are commuicatig with the service platform. Witex UDL via EMIZON 21 TCD To utilise the UDL optio ou will eed to sig up with the Emizo UDL service. After sigig up ou will be set our securit certificate alog with UDL server logi details. You will also be give the server IP ad port address. You will eed to eter these details i the Network details sectio of Pael details i Witex. You must also istall the Emizo UDL software o to the PC ou ited to use for UDL. Pael Com Port Setup The Com Port speed eeds to be cofigured to19200 baud if usig Com 2 ( Com 1 is set to baud at default ad caot be chaged ). See page 94 (Com Port Setup). Pael ARC Setup To set up the ARC accout ol a few settig eed to be made. see page 84 (Program Digi). Set the reportig Protocol to SIA or Cotact ID. Set a accout umber. Select Coect via IP i the protocol optios. see page 88 (Digi Optios). 96 INS176-9

97 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual WebWaOe WebWaOe itegratio with the cotrol paels provides the followig features 7 fuctios:- Automatic Commissioig ATS Moitorig ad Fault Reportig Alarm ad Fault reportig Remote Support Upload/Dowload Remote Maiteace The coectio is via a TTL lik to a Com Port o the cotrol pael. You will eed the followig to coect ad setup the module:- WebWaOe cable Witex software The WebWa solutio is quick ad eas to istall ad commissio with our chose ARC. A B C ON SIM + PWR A+ A- 1A 1B 2 A 2B 3A 3B P ower RT N BF MF TMP R-T T L-T B-48 5-A R T A B R TN P a el The Auto Take O process completes the istallatio. The WebWa servers automaticall programme the module to work seamlessl with the pael to eable SIA alarms, Upload Dowload ad secure remote access usig the Texecom Witex software. Automatic SIA 3 with text eriched messages All alarms geerated b the Alarm Sstem are automaticall set to the AMS usig SIA. SIA messages provide a full audit trail of a evet - which detector, locatio, time ad date, ad a permaet record of ever alarm. Messages for set ad uset iclude who, where, time, ad date, all recorded. Serial Pael Coectio Coect the coector cable to the Texecom oto Com Port 1. Com port 2 usuall has a local PC or other peripheral equipmet coected. Programmig the Cotrol Pael Digi Optios Eable commuicator must be ticked UDL passcode (set i the pael) must match. Dial attempts 1, rig before aswer 3 See page 88 I ARC s 1. Accout umber (site ID) 2. SIA Level 2/3 3. Coect Via IP - ticked 4. Sed SIA text ticked See page 84 I Radio-Pad ad Com Port optios 1. Com Port 1 WebWaOe module 2. Local IP address Local IP port Gatewa Subet Mask Name/SMG port See page 93 UDL & Digi Optios Witex Programmig All other settigs are doe b the Witex Comms meu This ca be cofigured o a local PC plugged o to Com Port 2 with the Module ruig o Com Port 1 or vice versa. Digi Optios Texecom TTL Cable WebWa SPT T - Red R - Gree RTN - Blue Texecom Com Port 1 Eter the optios show icludig the callback umber. Coect the WebWa PWR + ad - to a relevat Power (+12V/+24V) ad Groud (0V) termials. The Texecom pael cofiguratio is uploaded via the Witex software ad dowloaded to the pael o com port 2 from a local PC. The followig requires cofigurig i the pael. INS

98 UDL & Digi Optios Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual ARC's Accout No: should match the ARC Site/Chip ID ad tick the relevat trigger evet boxes relevat to the premises. Coect Via IP Checked Protocol SIA Level2/3 Radio Pad ad Com Port Optios If the SMS call cetre is utilised the egieer should eter the appropriate umber ad it should be cofigured uder: SMS Call Cetre 1&2 The SMS cetre telephoe umber is used to sed SMS text messages to mobile phoes. (Default = ). Com-IP Details if the pael is beig programmed with a laptop o com port 2, ad the WebWa is coected to com port 1 the SPT will be lost from the pael util the Witex sessio is closed. 98 INS176-9

99 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Chiro IRIS The Chiro IRIS Touch rage of commuicators offers a wa of trasmittig alarm sigals to a Alarm Receivig Cetre (ARC) over a Etheret (IP) path, GPRS path, ad PSTN path or a Combiatio as opposed to usig a traditioal PSTN lies. To coect to the cotrol pael a RS232 Iterface is required. For the IRIS 400 series this is a modified PC-Com JAA-0001 ad for the IRIS 600 series is a Chiro Tex 600 lead. UDL & Digi Optios Programmig For both Alarms ad Witex upload/dowload the followig should be programmed. UDL/DIGI Optios For full details o the optios listed please see page 84 to 94 Program Digi Arc 1 Protocol i.e. Fast Format, Cotact ID, or SIA level 2/3. Primar No Set this to the IP address of the Moitorig Cetre i a 12 digit format = The TTL coectio is made to either Com1 or Com 2 o the Cotrol pael. Secodar No Leave blaks as the IRIS Sstem will receive the secodar umber from the Moitorig Cetre Secure Apps platform. PCB Laout 0V for Pi Iputs Dial C a pture Chiro IR IS 400 Series Pi Iputs A-A B -B C -C D -D V FOR INP UTS INP UTS INP UTS Rela Outputs Aux Voltag e P O WE R Accout Number Eter i the accout umber from the Moitorig Cetre, 4or 6 digits. Dialler Attempts Leave as the default 3 Report optios The Reportig Optios will chage depedig o the alarm format selected, please set up the various reportig optio for the Alarm evet ou wish to sed to the Moitorig Cetre Cofig Eable the Coect via IP (Ke press 7). Serial RS232 R s 485 D- D+ T- T+ S IM C ard E theret Atea Digi Optios Eable the Digi UDL Optios UDL Password (ke press 1) ou should ow see E o optio scree ow. Must match the UDL password i Witex Setup Modules Setup IP Data 1 = ComIP Address for the IRIS e.g S YS P OLL DIAL US B S ER IAL RF GP R S E TH P STN T AMP E R 2 = ComIP Port Chiro IR IS 600 S eries Aux Voltag e 12V 0V A B 3 = ComIP Gatewa e.g To use DHCP leave the ComIP Address & Gatewa blak ComIP Netmask Eter the etwork subet mask i.e E theret S erial R S 232 Pollig/SMG IP Set this to the IP address of the Moitorig Cetre i a 12 digit format i.e = Com Port Setup Com Port 1 Set to IRIS IP Module Aux Voltag e INP UT S E TH SER GPRS POLL SYS A-A B-B R E L AYS S IM C a rd Atea GPRS Ifo To programme the APN ad the User Name & Password please see page 93 To programme ad commissio a other features of the IRIS uits please refer to the Chiro IRIS istallatio maual. PC Com Modificatio Cut the DB9 Male ed of off the PC Com ad wire as follows IRIS RS232 (DB9 Female) Pi 2 Pi 3 Pi 5 PC Com Yellow Blue Black Tex600 Lead 300mm INS

100 UDL & Digi Optios Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Zoe Alarm Reportig Codes The Reportig codes for Cotact ID ad SIA are full cofigurable, however these codes ca ol be chaged usig Witex dowloadig software. The followig tables show the default codes for each evet o the sstem: Default Zoe Evet Codes No Zoe Tpe Evet Reportig Group Cotact ID SIA 00 Etr/Exit 1 Alarm Alarm 134 BA Alarm Restore Restore 134 BH Omit Omit/Reistate 573 BB Reistate Omit/Reistate 573 BU 01 Etr/Exit 2 Alarm Alarm 134 BA Alarm Restore Restore 134 BH Omit Omit/Reistate 573 BB Reistate Omit/Reistate 573 BU 02 Guard Alarm Alarm 132 BA Alarm Restore Restore 132 BH Omit Omit/Reistate 573 BB Reistate Omit/Reistate 573 BU 03 Guard Access Alarm Alarm 132 BA Alarm Restore Restore 132 BH Omit Omit/Reistate 573 BB Reistate Omit/Reistate 573 BU 04 24Hr Audible Alarm Tamper 133 BA Alarm Restore Restore 133 BH Omit Omit/Reistate 572 BB Reistate Omit/Reistate 572 BU 05 24Hr Silet Alarm Tamper 133 BA Alarm Restore Restore 133 BH Omit Omit/Reistate 572 BB Reistate Omit/Reistate 572 BU 06 Audible PA Alarm Priorit Alarm 123 PA Alarm Restore Restore 123 PH Omit Omit/Reistate 573 PB Reistate Omit/Reistate 573 PU 07 Silet PA Alarm Priorit Alarm 122 HA Alarm Restore Restore 122 HH Omit Omit/Reistate 573 HB Reistate Omit/Reistate 573 HU 08 Fire Alarm Alarm Priorit Alarm 110 FA Alarm Restore Restore 110 FH Omit Omit/Reistate 571 FB Reistate Omit/Reistate 571 FU 09 Medical Alarm Priorit Alarm 100 MA Alarm Restore Restore 100 MH Omit Omit/Reistate 572 MB Reistate Omit/Reistate 572 MU 10 24Hr Gas Alarm Alarm Tamper 151 GA Alarm Restore Restore 151 GH Omit Omit/Reistate 572 GB Reistate Omit/Reistate 572 GU 100 INS176-9

101 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual UDL & Digi Optios No Zoe Tpe Evet Reportig Group Cotact ID SIA 11 Auxiliar Alarm Alarm Tamper 150 UA Alarm Restore Restore 150 UH Omit Omit/Reistate 572 UB Reistate Omit/Reistate 572 UU 12 24Hr Tamper Alarm Alarm Tamper 137 TA Alarm Restore Restore 137 TR Omit Omit/Reistate 572 TB Reistate Omit/Reistate 572 TU 13 Exit Termiator Alarm Ope/Close Alarm Restore Ope/Close Omit Omit/Reistate 570 UB Reistate Omit/Reistate 570 UU 14 Keswitch - Mometar Alarm Ope/Close 409 OP Alarm Restore Ope/Close 409 CL Omit Omit/Reistate 570 UB Reistate Omit/Reistate 570 UU 15 Keswitch - Latchig Alarm Ope/Close 409 OP Alarm Restore Ope/Close 409 CL Omit Omit/Reistate 570 UB Reistate Omit/Reistate 570 UU 16 Securit Ke Alarm Ope/Close 421 DK Alarm Restore Ope/Close 421 DG Omit Omit/Reistate 570 UB Reistate Omit/Reistate 570 UU 17 Omit Ke Alarm Omit/Reistate Alarm Restore Omit/Reistate Omit Omit/Reistate 570 UB Reistate Omit/Reistate 570 UU 18 Custom Alarm Omit/Reistate Alarm Restore Omit/Reistate Omit Omit/Reistate 570 UB Reistate Omit/Reistate 570 UU 19 Cofirmed PA Audible Alarm Priorit Alarm 123 PA Alarm Restore Restore 123 PH Omit Omit/Reistate 573 PB Reistate Omit/Reistate 573 PU 20 Cofirmed PA Silet Alarm Priorit Alarm 122 HA Alarm Restore Restore 122 HH Omit Omit/Reistate 573 HB Reistate Omit/Reistate 573 HU INS

102 UDL & Digi Optios Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual No-Zoe Evet Tpes The default No-Zoe Evet codes are as follows: No Tpe Evet Reportig Group Cotact ID SIA ID 22 Kepad Medical Alarm Priorit Alarm 100 MA Kepad No * Restore Restore 100 MH Kepad No * 23 Kepad Fire Alarm Priorit Alarm 115 FA Kepad No * Restore Restore 115 FH Kepad No * 24 Kepad Audible PA Alarm Priorit Alarm 120 PA Kepad No * Restore Restore 120 PH Kepad No * 25 Kepad Silet PA Alarm Priorit Alarm 122 PA Kepad No * Restore Restore 122 PH Kepad No * 26 Duress Code Alarm Alarm Priorit Alarm 121 HA User No Restore Restore HH User No 27 Alarm Active Alarm Not Reported Restore Not Reported Bell Active Alarm Not Reported Restore Not Reported Zoes Locked Out Alarm Alarm 130 BA Zoe No Restore Not Reported Verified Cross Zoe Alarm Alarm Alarm 130 BV 00 Restore Not Reported User Code Alarm Not Reported - - User No Restore Not Reported Exit Started Alarm Not Reported - - Kepad No Restore Not Reported Exit Error (Armig Failed) Alarm Ope/Close 457 EE 00 Restore Not Reported Etr Started Alarm Not Reported Restore Not Reported Area Arm Suite Alarm Ope/Close - - Suite No 1-8 Restore Ope/Close Armed with Lie Fault Alarm Not Reported - - User No Restore Not Reported Ope/Close (Full Arm) Alarm Ope/Close 401 OP User No Restore Ope/Close 401 CL User No 38 Ope/Close (Part Arm) Alarm Ope/Close 401 OP User No Restore Ope/Close 401 CL User No 39 Auto Ope/Close Alarm Ope/Close 403 OA 00 Restore Ope/Close 403 CA Auto Arm Deferred Alarm Ope/Close 405 CE User No Restore Ope/Close Ope After Alarm (Alarm Abort) Alarm Ope/Close 406 OR 00 Restore Not Reported Remote Ope/Close Alarm Ope/Close 407 OP 00 Restore Ope/Close 407 CL Quick Arm Alarm Not Reported Restore Ope/Close 408 CL Kepad No * 44 Recet Closig Alarm Ope/Close 459 CR 00 Restore Not Reported Reset After Alarm Alarm Restore - - Reset ID **** Restore Not Reported Power Output Fault Alarm Maiteace 300 YP Device ID ** Restore Restore 300 YQ Device ID ** 47 AC Fail Alarm Maiteace 301 AT 00 Restore Restore 301 AR INS176-9

103 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual UDL & Digi Optios No Tpe Evet Reportig Group Cotact ID SIA ID 48 Low Batter Alarm Maiteace 302 YT 00 Restore Restore 302 YR Sstem Power Up Alarm Maiteace 305 RR 00 Restore Not Reported Sstem Over Voltage Alarm Maiteace 321 YA 00 Restore Restore 321 YH ATS Path Fault Alarm Maiteace 351 LT Lie Fault ID *** Restore Restore 351 LR Lie Fault ID *** 52 Fail to Commuicate Alarm Maiteace 354 YC 00 Restore Not Reported Dowload Start Alarm Maiteace 411 RB 00 Restore Not Reported Dowload Ed Alarm Maiteace 412 RS - Restore Not Reported Log Capacit Alert (80%) Alarm Maiteace 623 JL 00 Restore Not Reported Date Chaged Alarm Maiteace 625 JD User No Restore Not Reported Time Chaged Alarm Maiteace 625 JT User No Restore Not Reported Istaller Programmig Start Alarm Maiteace 627 LB User No Restore Not Reported Istaller Programmig Ed Alarm Maiteace 628 LS User No Restore Not Reported Pael Box Tamper Alarm Tamper 145 TA 00 Restore Restore 145 TR Bell Tamper Alarm Tamper 145 TA Device ID ** Restore Restore 145 TR Device ID ** 62 Auxiliar Tamper Alarm Tamper 145 TA Device ID ** Restore Restore 145 TR Device ID ** 63 Expader Tamper Alarm Tamper 145 TA Device ID ** Restore Restore 145 TR Device ID ** 64 Kepad Tamper Alarm Tamper 145 TA Kepad No * Restore Restore 145 TR Kepad No * 65 Expader Trouble (Network Error) Alarm Tamper 333 ET Device ID ** Restore Restore 333 ER Device ID ** 66 Kepad Trouble (Network Error) Alarm Tamper 333 ET Kepad No * Restore Restore 333 ER Kepad No * 67 Fire Zoe Tamper Alarm Tamper 373 FT Zoe No Restore Restore 373 FJ Zoe No 68 Zoe Tamper Alarm Tamper 383 TA Zoe No Restore Restore 383 TR Zoe No 69 Kepad Lockout Alarm Tamper 421 JA Kepad No * Restore Not Reported Code Tamper Alarm Alarm Tamper 421 JA Kepad No * Restore Not Reported Soak Test Alarm Alarm Test - - Zoe No Restore Restore - - Zoe No 72 Maual Test Call Alarm Test 601 RX 00 Restore Not Reported Automatic Test Call Alarm Test 602 RP 00 Restore Not Reported User Walk Test Start/Ed Alarm Test 607 TS User No Restore Restore 607 TE User No INS

104 UDL & Digi Optios Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual No Tpe Evet Reportig Group Cotact ID SIA ID 75 NVM Defaults Loaded Alarm Not Reported - - Zoe No Restore Not Reported - - Zoe No 76 First Kock Alarm Not Reported Restore Not Reported Door Access Alarm Not Reported Restore Not Reported Part Arm 1 Alarm Not Reported Restore Close 401 CL User No 79 Part Arm 2 Alarm Not Reported Restore Close 401 CL User No 80 Part Arm 3 Alarm Not Reported Restore Close 401 CL User No 81 Auto Armig Start Alarm Not Reported Restore Close 401 CL Cofirmed Alarm Alarm Alarm 139 BV Zoe No Restore Not Reported Prox TAG Alarm Not Reported Restore Not Reported Access Code Chaged/Deleted Alarm Not Reported Restore Not Reported Arm Failed Alarm Not Reported Restore Not Reported Log Cleared Alarm Maiteace Restore Not Reported 401 CL id Loop Shorted Alarm Tamper 145 TA 000 Restore Restore 145 TR - 88 Commuicatio Port Alarm Maiteace Restore Restore TAG Sstem Exit (Batt. OK) Alarm Not Reported - - Zoe No Restore Not Reported - - Zoe No 90 TAG Sstem Exit (Batt. LOW) Alarm Not Reported Restore Not Reported TAG Sstem Etr (Batt. OK) Alarm Not Reported Restore Not Reported TAG Sstem Etr (Batt. LOW) Alarm Not Reported Restore Not Reported Microphoe Activated Alarm Not Reported Restore Not Reported AV Cleared Dow Alarm Not Reported Restore Not Reported Moitored Alarm Alarm Alarm 220 BA Zoe No Restore Restore 220 BH Zoe No 96 Expader Low Voltage Alarm Maiteace 143 ET Device No Restore Restore 143 ER Device No 97 Supervisio Fault Alarm Maiteace 355 UT Zoe No Restore Restore 355 UJ Zoe No 98 PA From Remote FOB Alarm Priorit Alarm Zoe No Restore Restore HA HH Zoe No 99 RF Device Low Batter Alarm Maiteace 384 XT Zoe/User No Restore Restore 384 XR Zoe/User No 100 Site Data Chaged Alarm Maiteace Restore Restore Radio Jammig Alarm Maiteace 344 XQ 000 Restore Restore INS176-9

105 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual UDL & Digi Optios No Tpe Evet Reportig Group Cotact ID SIA ID 102 Test Call Passed Alarm Not Reported Restore Not Reported Test Call Failed Alarm Not Reported Restore Not Reported Zoe Fault Alarm Maiteace 380 UT Zoe No Restore Restore 380 UJ Zoe No 105 Zoe Masked Alarm Alarm 380 UT Zoe No Restore Restore 380 UJ Zoe No 106 Faults Overridde Alarm Maiteace Restore Not Reported PSU AC Fail Alarm Maiteace 301 AT Device No Restore Restore 301 AR Device No 108 PSU Low Batter Fail Alarm Maiteace 302 YT Device No Restore Restore 302 YR Device No 109 PSU Low Output Fail Alarm Maiteace 300 YP Device No Restore Restore 300 YQ Device No 110 PSU Tamper Alarm Tamper 333 TA Device No Restore Restore 333 TR Device No 111 Door Access Alarm Ope 422 DG Device No Restore Not Reported CIE Reset Alarm Maiteeace 305 RR 000 Restore Not Reported Remote Commad Via Com Port 114 User Added Alarm Not Reported Restore Not Reported User Deleted Alarm Not Reported Restore Not Reported Cofirmed PA Alarm Priorit Alarm 139 BV Zoe No Restore Not Reported User Ack Alarm Not Reported - - Restore Not Reported Power Uit Failures Alarm Maiteace Alarm - YP - Restore Maiteace Restore - YQ Charger Fault Alarm Maiteace Alarm - YP - Restore Maiteace Restore - YQ - INS

106 UDL & Digi Optios Tamper Fault ID *** Pael ID is trasmitted as follows: Device ID Pael 000 Kepad ID is trasmitted as follows: Network RKP Expader ID is trasmitted as follows: Network EXP ATS Path Fault ID *** Lie Fault ID is trasmitted as follows: Device ID Pael 00 RedCARE 01 Com 300/Com Com IP 002 Expader ID is trasmitted as follows: Network EXP Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Reset ID **** Reset ID is trasmitted as follows: Device ID Pael (RR) 00 Egieer 01 Ati-Code 02 RedCARE 03 Keswitch 04 User 05 Witex 07 Expader ID is trasmitted as follows: Network EXP Power Fault ID **** Reset ID is trasmitted as follows: Device ID Bell Uder Voltage 00 Digi Uder Voltage 01 Sstem Uder Voltage 02 Aux Uder Voltage 03 Batter Uder Voltage 04 Network 1 Uder Voltage 05 Network 2 Uder Voltage* 06 Network 3 Uder Voltage** 07 Network 4 Uder Voltage** 08 Network 5 Uder Voltage** 09 Network 6 Uder Voltage** 10 Network 7 Uder Voltage** 11 Network 8 Uder Voltage** 12 *168 & 640 Ol **640 Ol 106 INS176-9

107 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Setup Users 5.8 Setup Users O User 010 Remote > Activate Device Activate the R adio FOB to assig it to the user Setup Users E ter User Number i.e. 10 = User 10 A Add TAG to User? 1=New, 2=Import 1 2 ASSIGNING TAG Preset TAG Now! IMPORTING TAG Preset TAG Now! P res s NO to exit Add TAG R outie P rese t TAG to assig it to user Setup Users User002:? Setup Users Eter User010: R Do You Wat to DELETE User 010? Pre s s YE S to de lete the User from ths sstem Eter User Code> E ter User code umber 4, 5 or 6 digits log e.g = 1234? Eter User Code> Allow Armig >A D O.... F U Aut o Yes A D O...>. F Use kes 1-8 to selec t a User optio or use the SCR OL L ke to searc h Press NO to select/deselect the User optio Use kes 1-8 to select areas e.g. 2 = B. Use the area ke to toggle betwee areas A to H ad I to P ( P remier 168 ol) F or 640 s ee below Aut o Yes A D O...>Y F User 10 Areas > > A******* < User 10 Tpe > Not I Use 2 Use kes 0-9 to selec t a Us er tpe e.g. 2 = Maager 2 All User tpes E xc e pt C u s tom User 10 Areas > > AB****** < User 10 Tpe > Maager If a Custom User tpe is selected, this User Optios meu will be displaed OPTIONAL If the User meu optio is ot selected If the User Meu optio is selected, the User Cofig meu will be displaed Chage Ow Code >C U Sstem Test C..>..... Sstem Tests C..>T.... Use kes 1-8 to selec t a Us er C ofig. or us e the SCR OL L ke to searc h Press NO to select/deselect the User optio User 10 Locked b Timer Select a Timer Cotrol e. g. 5 = T ime r C otrol 5 5 Press NO to edit the U ser ame text User 10 Locked b Timer 1 Use the ke pa d to program te xt the s a me wa tha t a mobile phoe works This optio is ol available to Users with the Door S trike attribute User 10 Door Ctl > ******** < 5 User 10 Door Ctl > ****5*** < User 10 Name is: ^Edit Text >ABC? Claire Edit Text ^>ABC OPTIONAL Add TAG to User? 1=New, 2=Import ASSIGNING TAG Preset TAG Now! IMPORTING TAG Preset TAG Now! Preset the Proximit TAG to the P r ox s m bol o th e k epad ad a beep will be heard User002 Area > 1 A*******<******* CP / Use the C hime & Part kes to s c roll betwe e Area Groups 1,2,3 & 4 User002 Area > 1 A*******<******* A Use the Area ke to select either A-H or I-P a rea s. Use the umeric buttos 1-8 to toggle the require d are as o or off Zoe 001 Areas1 *******>IJKLMNOP INS

108 Setup Users Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Default User Codes Whe the cotrol pael is first powered up ad the factor default settigs are loaded (see page 42 for details), ol the Egieer code ad the Master User code exist. The Factor default Egieer User code is. The Egieer is alwas User 00. If the Egieer code has bee lost or forgotte, it ca ormall be reset back to the factor default without havig to reprogram the etire sstem (see page 47 for details). Resettig the Egieer code is ol possible if the NVM has ot bee locked (see page 64 for details). The Factor default Master User code is. The Master User is alwas User 01. If the Master User code has bee lost or forgotte, it ca be reprogrammed b the Egieer i this meu. Programmig New Users Each User code o the sstem is made up of the followig elemets. Items 1, 2 or 8, 3 ad 4 which are essetial for the code to fuctio correctl ad items 5, 6, 7, 8 ad 9 which are optioal. 1. User Number Whe users are assiged to the sstem, the eed to be idetified b the cotrol pael. Each user is idetified as Users 01, 02, 03 etc. User 01 is alwas the Master User. 2. User Code This is a uique 4, 5 or 6 digit code umber that is assiged to a user. The sstem will allow a mixture of differet legth User codes. The User code must be etered at a kepad to operate the alarm sstem. There is a programmable Black List of baed user codes which ca be set ad edited via Witex UDL software. 3. User Areas A umber of areas ca be assiged to the selected user. Assigig areas to a user determies which areas ca be armed, disarmed, reset etc. b that user. I additio, assigig areas to a user determies which of the area related fuctios i.e. omittig zoes, silet armig etc. will be available to that user. 4. User Tpes The User tpe determies which fuctios are available to the user i.e. armig, disarmig, resettig etc. I additio, the User tpe also determies which optios the user ca access i.e. Setup Users, Sstem Tests etc. 5. User Time Lock This optio allows the selected user to be deied access to the sstem at differet times of the da ad das of the week. Whe a Cotrol Timer is assiged to a user, the User code will ot allow access to a fuctios durig the timers O period. 6. User Name Text Each user ca be assiged up to 8 characters of ame text. The ame text is displaed wheever a code is etered ad also whe readig the log, makig idetificatio of people usig the alarm easier. 7. Door Cotrol This optio would ormall be used for access cotrol. Users are able to ope/ulock doors that are assiged to their user code. 8. Proximit TAG As well as or istead of operatig the alarm sstem with a code umber, it is also possible to operate it b presetig a Proximit TAG to the kepad (this requires a Proximit kepad). User Tpes The User tpe determies which fuctios are available to the user i.e. armig, disarmig etc. I additio, the User tpe also determies which optios the user ca access i.e. Setup Users etc. The followig User tpes are available: 0: Egieer Egieers ca arm, disarm, omit zoes, silece alarms ad reset their assiged areas. I additio, Egieers ca access the Programmig Meu ad all User meu optios. Egieers ca also chage their ow User codes ad assig ew users to the sstem. 108 INS176-9 The default Egieer User tpe (User 00) ca assig a User tpes to the sstem. Egieers ca ol disarm areas that were armed usig a Egieer code. The caot disarm a areas that were armed with aother User code. 1: Master Master users ca arm, disarm, omit zoes, silece alarms ad reset their assiged areas. I additio, Master users ca access all User meu optios. Master users ca also chage their ow User codes ad assig ew users to the sstem. The Master user will also activate a output programmed as Door Strike. 2: Maager Maager users ca arm, disarm, omit zoes, silece alarms ad reset their assiged areas. I additio, Maager users ca access all User meu optios except Setup Users. Maager users ca also chage their ow User codes. 3: Stadard Stadard users ca arm all the areas assiged to the code ad disarm all the areas assiged to the code (eve if ol oe area is i etr or alarm) from a kepad, omit zoes, silece alarms ad reset their assiged areas. I additio, Stadard users ca access all User meu optios except for Setup Users, Sstem Tests, ad Chage Timers. Stadard users ca also chage their ow User codes. 4: Local Local users behave the same wa as Stadard users. However, Local users will ol arm the area that the kepad is assiged to ad disarm the area that is i etr or alarm (provided that the code has that area assiged to it 5: Duress Duress users behave the same wa as Stadard users. However, Duress users will activate a outputs programmed as Paic Alarm or Duress wheever their code is etered. Duress users ca ol be set up b a Egieer if sstem is set to Grade 3 see cofiguratio optio 37. 6: Arm Ol Arm Ol users ca ol arm or reset their assiged areas ad view the evet log. 7: Door Strike Door Strike users have o access to User fuctios or Meu optios. However, Door Strike users will activate a outputs programmed as Door Strike wheever their code is etered (see page 80 for details). 8: Vacatio Vacatio users behave the same wa as Stadard users. However, Vacatio users will automaticall be deleted the first time that the Master User code (User 01) is used to disarm the sstem. Vacatio user ca ol be deleted b the Master user after it has bee used to disarm the sstem at least oce. 9: Custom Custom users ca access a fuctios ad User meu optios that have bee assiged to them i User Optios 1 or 2 ad User Cofig. This flexibilit allows ew User tpes to be created that have their ow uique set of characteristics. A umber of Custom users ca be assiged to the sstem ad each oe will respod differetl, depedig o the fuctios ad features that have bee assiged to them.

109 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Setup Users User Fuctios ad Optios The table below shows the optios that are available to each user. All users that have access to the Armig Meu have the abilit to View Zoe Status, Set Chime Areas, View Act. Faults ad View Act. Couts. All users have access to the User Meu have the abilit to View Evet Log, Adjust Volumes ad Prit Evet Log. User Optios 1 Egieer Master Maager Stadard Local Duress Arm Ol Door Strike Vacatio Custom Armig Armig Armig Armig Armig Armig Armig - Armig - Disarmig Disarmig Disarmig Disarmig Disarmig Disarmig - - Disarmig - Omittig Omittig Omittig Omittig Omittig Omittig - - Omittig - Eg. Reset Local Armig Local Disarm Disarm First Disarm First Disarm First Disarm First Disarm First Disarm First - - Disarm First - User Optios 2 User Meu User Meu User Meu User Meu User Meu - User Meu - User Meu - Eg. Program Vacatio - Door Strike Door Strike Door Strike - - Call Rem. PC Call Rem. PC Call Rem. PC Duress Code Ope/Close Ope/Close Ope/Close Ope/Close Ope/Close Ope/Close Ope/Close - Ope/Close - User Cofig. Egieer Master Maager Stadard Local Duress Arm Ol Door Strike Vacatio Not Used Chage Code Chage Code Chage Code Chage Code Chage Code Chime Zoes Chime Zoes Chime Zoes Chime Zoes Chime Zoes Chage Timer Chage Timer Chage Timer Sstem Tests Sstem Tests Sstem Tests Setup Users Setup Users Eg. Access Eg. Access Eg. Access Eg. Access Eg. Access - Eg. Access - Eg. Access - Add Eg. code NVM Lockig INS

110 Egieer Utilities User Optios 1 This meu defies which optios are available to the user whe their code is etered. Press to scroll through the optios ad press to select them or use kes - ( Letter = optio IS selected, Star = optio is NOT selected). The followig optios are available: A - Armig Areas assiged to the selected user ca be armed. D - Disarmig Areas assiged to the selected user ca be disarmed. O - Omittig Zoes assiged to the same areas as the selected user ca be omitted, providig that the have the omit attribute assiged to them. R - Eg. Reset (Egieers ol) Areas programmed as Egieer reset ca be reset after a Alarm has occurred. a - Local Armig The User ca ol arm areas that the kepad is assiged to. d - Local Disarm The User ca ol disarm areas that the kepad is assiged to, or areas that are i etr or alarm (provided that the code has that area assiged to it). Y - Auto YES After a User code has bee etered, pressig the ke to cofirm the ext actio is ot required. F - Disarm First If a area is alread armed ad the selected user eters their code, the Disarm optio is displaed. User Optios 2 This meu is ol displaed if the Custom User tpe is selected (see page 109 for details). This meu defies which optios are available to the user whe their code is etered. Press to scroll through the optios ad press to select them or use kes - ( Letter = optio IS selected, Star = optio is NOT selected). The followig optios are available: U - User Meu The selected user has access to the User meu. However, the selected user will ol have access to optios assiged i User Cofig. (see page 110 for details). E - Eg. Program (Egieers ol) Ol Available to Egieers. D - Dual Code The selected user ca ol access a area whe a secod User code (with the Dual Code attribute ad also assiged to the same area) is etered. Dual Code users will also activate the 1 st ad 2 d Code output tpe. V - Vacatio The selected user is eabled the first time it is used to disarm the sstem ad ca be used as ma times as required. However, it will be automaticall deleted the first time that the User 01 code is used to disarm. Vacatio users will ol be deleted b the Master user, oce the have bee used o the sstem. S - Door Strike The selected user will activate a outputs programmed as Door Strike, wheever their codes are etered. Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual R - Call Rem. PC The selected user has access to the Call Remote PC optio, allowig them to iitiate a call to a remote upload/dowload PC. C - Duress Code The selected user will activate a outputs programmed as Duress, wheever their codes are etered. O - Ope/Close The selected user will report ope (disarm) ad close (arm) evets to a Alarm Receivig Cetre ever time the arm or disarm. User Cofig. This meu will ol be displaed if a Custom User tpe is selected AND User Meu (User Optio: U) is eabled (see page 110 for details). This meu defies which meu optios are available to the user whe their code is etered. Press to scroll through the optios ad press to select them or use kes - ( Letter = optio IS selected, Star = optio is NOT selected). The followig optios are available: C - Chage Code The selected user ca chage their ow User code. Z - Chime Zoes The selected user ca access the Edit Chime Zoes optio, allowig them to select which zoes chime whe activated. T - Chage Timers The selected user ca access the Override Timers, Alter Timers, Alter Part Arms, Alter Hol. Dates ad Edit Phoe No. meu optios. S - Sstem Tests The selected user ca access the Sstem Tests optio, allowig them to walk test zoes, activate the exteral souder etc.. U - Setup Users The selected user ca access the Setup Users optio, allowig them to alter existig users or assig ew users. However, users caot assig User tpes to the sstem that have a higher access level tha themselves. Also, if a user assigs a Custom User tpe, fuctios that are ot available to them caot be assiged to the Custom user. E - Eg. Access The selected user ca access the Eable Egieer optio, allowig them to authorise Egieer access or Remote UDL access to the sstem. A - Add Eg. Code (Egieers ol) Ol Available to Egieers. N - NVM Lockig (Egieers ol) Ol Available to Egieers. User Time Lock This optio allows the selected user to be deied access to the sstem at differet times of the da ad das of the week. Whe a Cotrol Timer is assiged to a user, the User code will ot allow access to a fuctios durig the timer O period (see page 68 for timer programmig). The first 4 optios (48) or 6 optios (88/168) will lockout the selected user (Code ad TAG) whe the correspodig cotrol timer is active. The last two optios will lock out the selected users TAG (T) whe Custom Output 2 Stage A is active or lock out the selected users Code (C) whe Custom Output 2 Stage B is active. This allows coditios to be set up i the custom outputs ad the the TAG or Code to be locked out durig those coditios i.e. Custom Output 2 Stage B could be programmed to activate durig etr, resultig i the code beig disabled durig the etr period. 110 INS176-9

111 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual User Name Text Each user ca be assiged up to 8 characters of ame text. This ca be beeficial whe readig the log, as idetificatio of people is made easier. See page 47 for details o programmig text. Text is programmed i a similar wa to mobile phoes. Select characters b pressig the correspodig ke the appropriate umber of times (to select a character o the same ke, press the ke to move the cursor alog). Door Cotrol This optio would ormall be used for access cotrol as it ol allows the user to ope/ulock doors that are assiged to that user code. Door cotrol is ol available to users with the Door Strike attribute assiged to it. Addig Tags Whe usig a Proximit Kepad, Tags ca be programmed or imported from aother pael. Whe prompted, select 1 to add ew Tag or 2 to import a Tag from aother sstem. Tags ca be imported from a other pael to a user ad it is possible to import Tags from several other paels. Deletig Users If a User code eeds to be deleted from the sstem, this must be doe, b a user that has access to the Setup Users meu. To delete User codes proceed as follows: Esure that Setup Users is selected, the displa should look like this: Do ou wat to Setup Users? Press, the displa should look like this: Setup Users Eter User -- Select a user from 1 to 24 (48), 1 to 49 (88) or 1 to 199 (168) the press, the displa should look like this: Eter User Code> Egieer Utilities choose which zoes (ad therefore expader) the Premier Elite SmartKe will use for its routeig, LED ad Aux fuctios ca also be chaged withi the Setup Users meu. All users o the sstem ca have a Premier Elite SmartKe a TAG ad a code, or a combiatio of them. This sectio ol deals with Premier Elite SmartKe learig ad routeig, all other user programmable optios ca be foud i INS176-8 Premier Elite Series Istallatio Maual or later. Great care should be take whe usig large umbers of Premier Elite SmartKe, ol oe Premier Elite SmartKe per expader ca be used b the sstem at a oe time, ad o Multiple expaders sstems, or large sites, fuctioalit should be checked i all areas of the site where the device ma be used. Premier Elite SmartKe Routeig Premier Elite SmartKe should ol be leared to the sstem AFTER all devices have bee leared ad placed i their fial locatio. Whilst it is possible to lear at a poit durig the programmig of the sstem, learig ad testig the fuctioalit of the Premier Elite SmartKe after all devices have bee placed will esure that the Premier Elite SmartKe performs as expected, ad works i locatios where the user would expect it too. Route B The Route B fuctio allows ou to select which Zoes (ad therefore expader) the Premier Elite SmartKe will use o the sstem for its routeig. This should be selected BEFORE the device has bee leared. I the examples below Fig 1 shows the zoes associated with Expader 1, which is a 32XP-W, ad Fig 2 shows Expader 2 which is also a 32XP-W, whe usig 8XP-W there willobviousl be less devices that the Premier Elite SmartKe ca use. User001 Route B Zoes User001 Route B Zoes Fig 1 Fig 2 The ke is used to select this meu ad the ke used to select which expader ad associated zoes will be used Oce a Premier Elite SmartKe has bee leared the ke will show which zoes are beig used for routeig. It is ot possible to alter this oce leared. To chage the routeig the Premier Elite SmartKe should be deleted ad the process started from the begiig. Deletig a Premier Elite SmartKe Deletig the Premier Elite SmartKe from the user is a similar process to learig, at the appropriate poit i the meu press followed b, the Premier Elite SmartKe will be removed from the User. To delete all user data see INS176-8 or later. Press, the displa will look somethig like this: Do ou wat to DELETE User 15 Where 15 is the selected User umber. Press to cofirm deletio of the selected User code Press to exit from Setup Users Addig SmartKe Itroductio Premier Elite SmartKe are ow leart ad all fuctioalit maaged through the Setup Users Meu. Ricochet MT2 ad Premier Elite Series V2 firmware upgrades add additioal capabilities to the maagemet of Premier Elite SmartKe. I multiple expader sstems it is ow possible to Setup Users Setup Users User002: O User002 Ricochet Free User002 Ricochet Learig... 20s User002 Ricochet Fob LED Aux? User002 Ricochet Fob --- Aux A * 1 to toggle LED o or off * 2 to toggle Aux o or off R N U Use U scroll to ext us e r Us ig the A ke at this poit allows ou to view the group of zoes, a d therefore the expader that the S martke will use. Us e the U ke to sele ct the group of Zoes ad Expader ou wat to use User002 Route B Zoes User002 Route B Zoes U INS

112 Egieer Utilities Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 5.9 Egieer Utilities View Evet Log Egieer Utils Egieer Utils View Evet Log 1=Evet,2 =Alarm 3=Madator Log 1 PROG. START 12: /03 U Code 01 David 12: /03 C Code 12 Joh 12: /03 A Code 01 David Area: A... P Code 01 David Area: A... N Use kes 1, 2 or 3 to select the Sstem, Alarm or Madator log i.e. 1= Sstem Log Use the S C R O LL ke to move up ad dow through the log. DO WN moves to the previous evet ( backwards i time) ad UP moves forwards agai. Or use oe of the available hotkes Pre ss C HIME. to fid a precedig evets relatig to the displaed evet i.e. User codes beig etered Press AREA. to toggle the displa betwee the Area iformatio ad the time /date Press PART to displa a programmed zoe text etc. The cotrol pael has three Evet Logs, which are time ad date stamped. The first log which is a sstem log, records all evets that occur o the sstem, i.e. Users eterig their codes to arm or disarm areas, alarm evets, failures to arm etc. The secod log which is a alarm log, ol records alarm evets that occur o the sstem. The third log is the Madator Evet log which records ol evets defied as madator b EN The Sstem Log records the last 500 (48), 1000 (88) or 2000 (168) evets. The Alarm Log records the last 32 alarm evets. The Madator Log records the last 500 madator evets. Evet Log Hotkes Whe viewig the sstem log there are 9 hotkes available. These hotkes allow certai evets to be foud easier without the eed for searchig. The followig hotkes are available: = Priorit Alarms (PA, Fire etc.) = Normal Alarms (Guard, 24hr, Etr/Exit etc.) = Opes ad Closigs (Arm, Disarm etc.) = Omits ad Reistates (Zoe Omits etc.) = Maiteace (Sstem Tests, Egieer Program etc.) = Tampers (Zoe, Bell, Aux etc.) = Test Calls (Commuicator Active, successful etc.) = Etr/Exit (Etr ad Exit Procedures) = User Codes (User codes beig used) 112 INS176-9

113 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Evet Log Descriptios Egieer Utilities Log Evet Descriptio ### ARM FAILED A exit fault from Zoe ### has caused the sstem to fail to arm ### Flt Alarm Zoe ### has detected a Fault coditio ### Mask Alarm Zoe ### has detected a Mask coditio ### Test Failed Zoe ### has activated whilst it has bee o soak test ### Tested OK Zoe ### has activated durig the walk test #,# RESET AREAS - Area have bee reset usig kepad #,# followig a Itruder alarm AC Off Alarm The cotrol pael has detected a AC Mais failure ALARM ABORT A Ope After Alarm-Abort has occurred for area? ALARM Active A Itruder alarm sigal has bee activated for area? Ati-Code Reset A reset has bee performed usig the Ati-code reset procedure AREA Armed Area? has bee armed AREA Disarmed Area? has bee disarmed ARMED WITH L/F The sstem has bee armed with a Lie Fault coditio preset ARMING FAILED A Exit Error-Arm Fail has occurred o area? ARMING SUITE # Area Arm Suite # was used to arm the sstem ATS FAILED The Commuicator has failed to report to the Alarm Receivig Cetre ATS FLT Alarm There is a problem with the telephoe lie AUTO TEST CALL A Automatic test call has bee iitiated AUX #,# Tamper A Auxiliar Tamper iput from device #,# has bee activated AV CLEARED b ## The Audio Verificatio uit has bee cleared dow b user ## BELL #,# Tamper A Bell Tamper iput from device #,# has bee activated BELL Active The Bell output has bee activated for area? BELL FUSE Alarm The cotrol pael Bell Fuse has failed BOX LID Tamper The cotrol pael lid has bee removed causig a Tamper alarm CHARGER FAULT Batter Charge Curret has Failed CIE Reset The iteral processor has failed its self checks. CODE #,# Tamper Too ma ivalid ke presses have caused a tamper alarm from kepad #,# Com??? Lie Fault The Com300, 2400 or ISDN has detected a lie fault COM PORT Alarm A com port has geerated a alarm CONFIRMED ALARM Two or more detectors have activated, resultig i a cofirmed alarm coditio CONFIRMED PA Two or more PA zoes have activated, resultig i a cofirmed PA alarm coditio CONFIRMED INTRUDER Two or more detectors have activated, resultig i a cofirmed Itruder coditio CORRUPT EVENT No evet has bee stored i memor CROSS ### Alarm A Verified Cross Zoe (Beam Pair) Alarm has occurred from zoe ### DATA CHANGED Programmig data has bee chaged DATE CHANGED The cotrol pael Time has bee chaged DEFAULTS LOADED The factor default values have bee loaded ito memor DEFERRED The armig mode was deferred for area? DOOR #,# Door #,# has bee opeed b a user with Door Cotrol DOWNLOAD START A Upload/Dowload has bee iitiated DOWNLOAD END The Upload/Dowload has fiished DURESS User ## has etered a Duress Code at a kepad Egieer Reset A reset has bee performed usig a Egieers code ENTRY Area ## The Etr mode has bee started for area? EXIT Area ## The Exit mode has bee started for area? EXP #,# Reset A reset has bee performed usig the iput o expader #,# (programmed as reset) EXP #,# Lie Fault The Iput o expader #,# (programmed as lie fault) has bee activated EXP #,# LOST Expader ## has bee lost from the etwork EXP #,# Tamper The cover of expader #,# has bee removed EXP ## Low Voltage Expader #,# has detected that its suppl voltage is low F_PA ## A Paic Alarm from a Radio FOB has bee geerated Fault Override The sstem has bee armed with a Fault coditio preset b a user FIRE ### Active Zoe ### (programmed as Fire Alarm) has caused a alarm FIRE ### Tamper Zoe ### (programmed as Fire Alarm) has caused a Tamper alarm FIRST KNOCK ### Zoe ### (which is programmed as double kock) has activated for the first time FUSE #,# Alarm The Auxiliar 12V Fuse i device #,# has failed GSM MODULE LOST The GSM Module has lost commuicatios with the cotrol pael id Loop# Tamper There is a short circuit o id loop # o the id expader Ke switch Reset A reset has bee performed usig a ke switch KSW ### Disarmed A Keswitch zoe tpe has bee activated (zoe umber ###) LOG ALERT 80% of the Evet Log has filled (sice the last Upload/Dowload) LOG CLEARED The evet log has bee erased LOW BAT Alarm The cotrol pael has registered a low batter coditio LOW V #,# Alarm Expader #,# has detected that s its suppl voltage is low MANUAL TEST CALL A Maual test call has bee iitiated MIC ## TESTED Microphoe ## o the Audio Verificatio Module has bee tested Moitored Alarm A zoe programmed as ke tube has caused a alarm No RF Sigal ### The Wireless receiver has detected a sigal loss from zoe ### PA From Remote FOB A PA has bee geerated from a Remote Fob Pael Lie Fault The cotrol pael lie fault iput has bee activated PART Armed Area? has bee Part Armed PART 1 Armed Part Arm 1 has bee selected PART 2 Armed Part Arm 2 has bee selected PART 3 Armed Part Arm 3 has bee selected POWERED UP Sstem Power Up (without doig a factor restart) POWER O/P FAULT The sstem has geerated a Power Output Fault see Table Power ID Fault o Page 98 POWER UNIT FAILURE The sstem has geerated a rate of voltage failure PROG. END The Egieer has logged out of the Programmig meu PROG. START A Egieer code has bee etered PSUac ## Alarm A expader iput programmed as PSU Moitor cotrol pael has detected a AC Mais failure PSUbat## Alarm A expader iput programmed as PSU Moitor cotrol pael has detected a Batter fault PSUvol## Alarm A expader iput programmed as PSU Moitor cotrol pael has detected a 12V Output failure INS

114 Egieer Utilities Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Log Evet Descriptio PSUTam## Alarm A expader iput programmed as PSU Moitor cotrol pael has detected a Tamper coditio QUICK Armed Quick Arm from kepad #,# R/Bat ## Alarm The Wireless receiver has detected a low batter sigal from device ## Radio Jammig The Wireless receiver has detected a attempt to jam its radio sigal RADIO PAD LOST The Radio-Pad has o sigal or has lost commuicatios with the cotrol pael REARM LOCK ### Zoe ### has locked out after reachig its re-arm limit (after causig a alarm) RECENT Armed Area? has bee armed recetl Redcare Lie Fault The Redcare has detected a lie fault REMOTE Armed Area? was armed usig the Witex UDL software REMOTE Disarmed Area? was disarmed usig the Witex UDL software Remote PC Reset A reset has bee performed b the remote dowload PC Remote Reset A reset has bee performed usig the Remote Reset iput Redcare Reset A reset has bee performed b the Redcare RF Device ###Low Batter RF Device ### has registered a low batter coditio RKP #,# MEDICAL A Medical alarm (7 & 9) has occurred from kepad umber #,# RKP #.# FIRE A Fire alarm (4 & 6) has occurred from kepad umber #,# RKP #,# AUD PA A Audible PA alarm (1 & 3) has occurred from kepad umber #,# RKP #,# SIL PA A Silet PA alarm (1 & 3) has occurred from kepad umber #,# RKP #,# Tamper The cover of kepad #,# has bee removed RKP #,# LOST Kepad ## has bee lost from the etwork RKP LOCKED #,# Kepad #,# has bee locked out from too ma ivalid ke presses Site Data Chaged Site Data has bee chaged e.g. zoe ### has bee chaged Supervisio Fault A Radio device has failed to poll back to the pael withi the Supervisio Time Sstem Over Voltage The cotrol pael Bell Fuse has failed TAG ## User ## has preseted their Prox TAG Test Call Passed Maual or Periodical Test Call has passed Test Call Failed Maual or Periodical Test Call has failed TESTED ### Zoe ### has bee tested TEST FAIL ###) Zoe ### has failed its Soak test TAG Sstem Exit (Batt. OK) The sstem has bee put i to exit via tag ad batter voltage is ok TAG Sstem Exit (Batt. Low) The sstem has bee put i to exit via tag ad batter has low voltage TAG Sstem Etr (Batt. OK) The sstem has bee put i to etr via tag ad batter voltage is ok TAG Sstem Etr (Batt. Low) The sstem has bee put i to etr via tag ad batter has low voltage TIME Armed Area? was armed automaticall usig oe of the cotrol timers TIME CHANGED The cotrol pael Date has bee chaged TIME Disarmed Area? was disarmed automaticall usig oe of the cotrol timers TUBE ### Alarm Zoe ### (programmed as Ke Tube) has caused a alarm USER ## User ## has etered their code User Ack A user has ackowledged a fault to set sstem USER CODE CHANGED A User code has bee altered USER ADDED A User code has bee added USER DELETED A User code has bee deleted User Reset A reset has bee performed usig a User code WALK Test Start The Walk Test mode has bee iitiated Zoe ### Alarm Zoe ### has bee activated Zoe ### Tamper Zoe ### has caused a Tamper alarm Zoe ### Restore Zoe ### has restored to its ormal coditio Zoe ### Omitted Zoe ### has bee omitted Zoe ### U-Omit Zoe ### has bee reistated Zoe ### Test Start Zoe ### has bee put o test Zoe ### Test Ed Zoe ### has bee removed from test Zoe ### Fault Zoe ### has geerated a Fault Coditio Zoe ### Masked Zoe ### has bee Masked 114 INS176-9

115 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Egieer Utilities Do Bell Test Do Walk Test 24/48/88/168 Egieer Utils Egieer Utils View Evet Log 1 Egieer Utils Do Bell Test Push YES to test Bell is >Off O Push YES to test Bell Disabled U Push YES to test Digi > ******** Push YES to test Digi > ******** 3 Push YES to test Digi > ******** N Pres s O MIT to ivoke the Egieers Hold Off mode of a Texecom B ellbox Use the S CROLL ke to select the required test Pres s YE S to tes t ALL chaels or use kes 0-8 to select idividual chaels e.g. 3 = C ha el 3 Press YE S agai to clear ALL chaels or use kes 0-8 to clear idividual c haels e.g. 3 = C ha el 3 This optio allows the Bell, Speaker ad various cotrol pael outputs to be tested. The followig outputs ca be idividuall tested: Test Bell Test Strobe Test Speaker Test Digi Test Pael Test RedCARE Test Com???? LCD Displa User Outputs The Bell output The Strobe output The Speaker output The Hardwired digicom outputs The pael outputs The plug o RedCARE outputs The plug o Com 300/2400 digi chaels The LCD kepad displa A outputs that have the User Test attribute (see page 81 for details). Pressig OMIT at the Bell or Strobe Test will cause the Strobe output to pulse 3 times, ivokig Egieers Hold Off mode if a Texecom bell box is coected. Egieer Utils Egieer Utils View Evet Log 2 Egieer Utils Do walk test? Walk test Areas> > ABCDEFGH < * NONE * C Zoe 005 Louge PIR A Zoes that eed testig are :? Zoe 001 >007 Frot Door N P res s YE S to walk tes t all areas or use kes 1-8 to select/deselect areas Press CHIME to select: Chime Oce the lockout zoe Chime o ever ac tivatio or No Chime at all Press ARE A. to toggle the displa betwee the zoes that have bee tested ad the zoes that still eed testig To view zoes that ha ve ot activated recetl, eter the umber of das required i.e. 007 will s how zoes that have o t ac ti va te d i the las t 7 das A of the zoes o the sstem ca be walk tested to esure that the operate correctl. A walk test ca ol be performed whe the sstem or area is disarmed. Oce a zoe has bee activated it will ot geerate a chime toe agai. If however the ke is pressed, a zoe will chime ever time it is activated. The Walk test meu also icludes a last activatio log that ca be recalled whe doig a walk test. This log shows zoes that have NOT bee activated over a period of das. Pressig the ke will firstl show the zoes that still eed testig, pressig the ke a secod time will displa the zoes that have ot bee activated that da, to view zoes that have ot bee activated for 3 das, tpe i 003 the maximum umber of das that ca be recalled is 255, pressig the ke a third time will revert back to the stadard walk test displa. INS

116 Egieer Utilities Do Walk Test 640 Egieer Utils Egieer Utils View Evet Log 2 Egieer Utils Do walk test? Walk test Areas1> ABCDEFGH<JKLMNOP CP / Walk test Areas4> ABCDEFGH<JKLMNOP A Walk test Areas4> ABCDEFG>******** * NONE * C Zoe 005 Louge PIR A Zoes that eed testig are :? Zoe 001 >007 Frot Door N Use the C hime & Part kes to s c roll betwe e Are a G roups 1, 2, 3 & 4 Use the Area ke to select either A-H or I-P a rea s. Us e the ume ric buttos 1-8 to toggle the re quired areas o or off Press CHIME to select: Chime Oce the lockout zoe Chime o ever activatio or N o C him e a t al l Press AREA. to toggle the displa betwee the zoes that have bee tested ad the zoes that still eed testig To view zoes that have ot activated recetl, eter the umber of das required i. e will s how zoe s that ha ve ot activa te d i the las t 7 das Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual View Zoe Status Egieer Utils Egieer Utils View Evet Log 3 Egieer Utils View Zoe Status Zoe 001 Pael 1 Secure 2k2? Zoe 064 N1,E7,8 Secure 2k2 Zoe 064 N1,E7,8 Active 6k9 O ZoeX064 N1,E7,8 Zoe Disabled N Use kes 0-9 to eter the required zoe umber or use the S C RO LL k e to sea rch e.g. 064 = Zoe 64 To disable the zoe, Press OMIT. To make the zoe C hime, Press CHIME To view the zoe text, Press AREA This optio ca be used to view the status of a zoe o the sstem to see whether it is Active, Secure, Tampered or Shorted. The selected zoe ca also be temporaril disabled (zoe ad tamper) to allow the zoe to be worked o or made to chime ever time it is activated. Whe leavig the View Zoe Status meu, all zoes will be automaticall reistated ad cleared of Chime. A of the zoes o the sstem ca be walk tested to esure that the operate correctl. A walk test ca ol be performed whe the sstem or area is disarmed. Oce a zoe has bee activated it will ot geerate a chime toe agai. If however the ke is pressed, a zoe will chime ever time it is activated. The Walk test meu also icludes a last activatio log that ca be recalled whe doig a walk test. This log shows zoes that have NOT bee activated over a period of das. Pressig the ke will firstl show the zoes that still eed testig, pressig the ke a secod time will displa the zoes that have ot bee activated that da, to view zoes that have ot bee activated for 3 das, tpe i 003 the maximum umber of das that ca be recalled is 255, pressig the ke a third time will revert back to the stadard walk test displa. 116 INS176-9

117 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Egieer Utilities Do Sstem Tests Cofirm Devices Egieer Utils Egieer Utils View Evet Log 4 Egieer Utils Sstem Tests Do ou wat to View Ss. Status Ss Voltage>13.7 Ss Curret>0689 Use kes 1-4 to select a optio or use the SCR OLL ke to searc h e.g. YES = View Ss. Status This optio allows various cotrol pael features to be tested or reviewed. 1 - View Ss. Status Allows the sstem voltage ad curret to be viewed. 2 - View Batt Status Allows the batter voltage ad chargig status to be viewed. 3 - Test Outputs Allows the Bell, Speaker ad sstem outputs to be tested. 4 - View Versio No. This optio allows the cotrol pael software versio ad serial umber to be viewed. Egieer Utils Egieer Utils View Evet Log 5 Egieer Utils Cofirm Devices Net RKP> Exp>... U Net RKP> Exp>1... Press YES agai to Cofirm. Net RKP> Exp>1... A Net Errors> Last RKP> 1 R Net Errors> Last RKP> 1 Us e the S C RO LL k e to select the required etwork Pres s YE S if the umbe r of devices fitted is correct. A X o the displa idicates that a device was previous fitted Press YES to cofirm the devic es fitted (a cofirmatio toe will be heard) P res s AR E A to vie w the etwork errors ( the total umber of errors o the e twork ad the la s t devic e to cause a error is beig displaed) Press RESET to clea r the etwork errors This optio allows the etworks to be viewed to see what devices are coected ad whether there are a problems. Wheever ew devices are added to the sstem, the etworks must be checked ad cofirmed. If a devices are removed from the sstem, the etworks must be rechecked ad recofirmed. A X o the displa idicates that device that was previous fitted is o loger beig see b the cotrol pael. INS

118 Egieer Utilities View RKP Status Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Set Sstem Time Egieer Utils Egieer Utils View Evet Log 6 Egieer Utils View RKP Status N1,R1 Z1=. Z2=. *NOT Fitted*? N2,R3 Z1=H Z2=H Tamp=H Output=0 Use kes 1-8 to select a kepad ad press 0 to toggle betwee etworks e.g. 0, 3 = Network 2, Kepad 3 Press AREA to displa errors P res s N O to te s t o u tpu t Press OMIT to test souder This optio allows the status of the kepad, the zoes ad the output to be viewed. View Exp. Status Egieer Utils Egieer Utils View Evet Log 7 Egieer Utils View Exp. Status N1,E *Not Fitted*? N2,E Zoes HHHHHHHH N2,E Outputs... N Use kes 1-8 to selec t a expader a d press 0 to toggle betwee etworks e.g. 0, 2 = Network 2, E xpa der 2 Press AREA to chage betwee zoes /volta ge/outputs /errors (ad PS U status if PS U200XP fitted) Press CHIME to test zoes Press OMIT to test souder Pres s 1-8 to te s t outputs If P SU 200 XP Fitted AA N2,E2-PSU V:13.5 I:0656mA: S:... N This optio allows the status of the expader, the zoes, voltage/iputs ad outputs ad a moitored power suppl to be viewed. The PSU status shows the followig codes:. A: AC Mais Fail 1: Batter 1 Fault 2: Batter 2 Fault F: Mais Fuse Blow T: PSU Box Tamper Egieer Utils Egieer Utils View Evet Log 8 Egieer Utils Set Sstem Time? Eter ew time > 00:00? Eter ew time > 16:45 Use kes 0-9 to eter the ew time (24-Hour format) e.g = 4:45 pm The cotrol pael has a real time clock that is used to date ad time stamp evets that are recorded withi the sstem log. The optio allows ou to set the cotrol pael time. Set Sstem Date Egieer Utils Egieer Utils View Evet Log 9 Egieer Utils Set Sstem Date? Eter ew date > 01/01/01? Eter ew date > 03/05/01 Use kes 0-9 to eter the ew date DD/MM/YY e.g = 3rd Ma 2001 The cotrol pael has a real time clock that is used to date ad time stamp evets that are recorded withi the sstem log. The optio allows ou to set the cotrol pael date. 118 INS176-9

119 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Egieer Utilities Chage Eg. Code Default NVM Data Egieer Utils Egieer Utils Egieer Utils View Evet Log U Egieer Utils View Evet Log U Egieer Utils Chage Eg. Code Egieer Utils Default NVM Data Eter New Code > ? Eter New Code > Eter User code umber 4, 5 or 6 digits log e.g = 1234 Press YES Reset: Pael Outputs 3 Press YES Reset: Kepad Outputs Use kes 0-9 to selec t a optio or use the S C R OL L ke to s e arc h e.g. 3 = K epad O utputs Press YES to default the optio This optio allows the Egieer code (User 00) to be chaged. This code ca be 4, 5 or 6 digits i legth. The sstem will allow a mixture of differet legth User codes. Kepad Outputs * Please Wait! * Adjust Volumes This optio allows various parts of the NVM to be defaulted without havig to Factor Default the sstem. Egieer Utils Egieer Utils View Evet Log U Locatio Text Egieer Utils Egieer Utils Adjust Volumes Pael Volume Level = 6 U Kepad 03 Volume Level = 4 Kepad 03 Volume Level =>4 8 Kepad 03 Volume Level =>7 Use the SCR OLL ke to selec t a Pael, Kepad or Expader Speaker E te r a value or us e th e SCR OLL ke to ic rease or dec rease the value e.g. 8 = Full Volume Egieer Utils View Evet Log U Egieer Utils Locatio Text No Locatio Text Has Bee Setup This optio allows the Pael Locatio text that has bee programmed i Sstem Text to be displaed (see page 69 for programmig details). The displa will automaticall clear after 5 secods. This optio is used to adjust the volume level of speakers that are coected to the cotrol pael, kepads ad expaders. Pressig the CHIME ke will cause the speaker that is beig programmed to geerate the exit toe at the selected volume level. INS

120 Egieer Utilities Prit Log Data Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Soak Test Areas 640 Egieer Utils Egieer Utils Egieer Utils View Evet Log U Egieer Utils Prit Log Data Number of Evets: > 0000? Number of Evets: > 0050 E te r a value or use th e SCR OLL ke to ic rease or dec rea se the value e.g. 50 = Las t 50 E vets Press YES to prit This optio allows the Evet Log to be prited to a stadard RS232 priter (see page 41 for details). Egieer Utils View Evet Log U Egieer Utils Soak Test Areas Soak Test Areas1...<... CP / Soak Test Areas1...<... A Soak Test Areas1 ABCDEFGH<... Use the C hime & Part kes to sc roll betwe e Are a G roups 1, 2, 3 & 4 U se the Area ke to select either A-H or I-P a rea s. Use the umeric buttos 1-8 to toggle the require d are as o or off Press YES to default the optio Soak Test Areas 24/48/88/168 Egieer Utils Egieer Utils View Evet Log U Egieer Utils Soak Test Areas Soak Test Areas: > A*... < 2 Soak Test Areas: > AB... < Use kes 1-8 to selec t area s e.g. 2 = B. Use the area ke to toggle betwee area s A to H a d I to P Press YES to default the optio Whe a area is selected for soak test, the soak test timer is started. A zoes i the selected area with the soak test attribute will be put o soak test for the duratio of the soak test timer (see page 62). If the area soak test optio is subsequetl deselected before the ed of the test, all zoes are retured to ormal operatio. Whe a zoe is o soak test, it will ot cause a alarm whe activated. However the sstem will log the evet ad will otif the user that the zoe has failed soak test. A test failure will ot prevet the user armig the sstem ad will be cleared whe the egieers code is etered. At the ed of the soak test all zoes that have passed the test will be retured to ormal operatio. Whe a area is selected for soak test, the soak test timer is started. A zoes i the selected area with the soak test attribute will be put o soak test for the duratio of the soak test timer (see page 62). If the area soak test optio is subsequetl deselected before the ed of the test, all zoes are retured to ormal operatio. Whe a zoe is o soak test, it will ot cause a alarm whe activated. However the sstem will log the evet ad will otif the user that the zoe has failed soak test. A test failure will ot prevet the user armig the sstem ad will be cleared whe the egieers code is etered. At the ed of the soak test all zoes that have passed the test will be retured to ormal operatio. 120 INS176-9

121 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Egieer Utilities View id Data Cofigure Radio Egieer Utils Egieer Utils View Evet Log U Egieer Utils View id Data N N A Q A id Loop 1,01 Mapped Zoe 000 U id Loop 1,01 Mapped Zoe>000? id Loop 1,01 Mapped Zoe>010 O id Loop 1,01 Mapped Zoe>010* id Loop 1,01 Mapped Zoe 010* N Press 0 to toggle betwee id L oop 1 a d 2 The status of the zoes will be displaed Press Are a to toggle betwee Normal loop sca Q uick loop sca ad B iscuit Mappig Press 0 to toggle betwee id Loop 1 ad 2. Use S croll kes to select the required id biscuit. Press No to edit the zoe mappig ad wirig optios. Us e k es 0-9 to e ter the zoe umber Press O mit to toggle betwee N ormall Ope ad Normall C losed wirig. * = Normall Ope. Viewig the id Data This optio allows the 60IXD expader the id bis cuit data to be viewed to diagostic purposes. There are two wa of viewig the data from the expader: Normal S ca Mode This is the ormal operatio mode of the expader ad the data beig displaed is the average result of 4 successive scas of the id loop. Quick Sca Mode I this mode the data beig displaed is the result of each sca of the id loop. This mode is useful for idetifig problems with biscuits due to iterferece, high resistace coectios etc. id is a registered trade mark of Chloride Safet Sstem Limited. Egieer Utils Egieer Utils View Evet Log U Egieer Utils Cofigure Radio 01: ID OK SL:000 Zoe 000 U 23: No Device 20, YES, To Lear 23: No Device 18 Activate Device P ress Lear s witch ad is ert batter/po wer up S martke. 23: ID4DD3C3 TAMP SL:085 Zoe : ID4DD3C3 OK SL:085 Zoe>000? 23: ID4DD3C3 OK SL:085 Zoe>018 23: ID4DD3C3 OK SL:085 Zoe 018 N Use kes 0-9 to eter the required device umber or use the SC ROLL ke to search e.g. 23 = Device 23 If Device alread programmed ID will show here Pres s YE S to lear Radio Device If Device alread programmed ID will s how here Press RE SE T to Delete Radio Device Pres s N O to map the device to a zoe/user Use kes 0-9 to eter the required zoe/user umber or use the SC ROLL ke to search e.g. 18 = Zoe 18 Top Lie = Serial umber ad status of device Bottom Lie = Sigal stregth ad zoe/user umber Cofigurig Radio devices (NOT MT2 Sstems) Up to 32 wireless devices ca be leart o to the sstem this ca be a combiatio of detectors, mag cotacts ad remote FOBs. The umber of remote FOBs is limited to the maximum umber of devices the expader ca accept. Wireless devices ca the be mapped o to the sstem alog with covetioal detectors. The top lie o the displa shows the serial umber of the device ad also the status i.e. Active, Tamper etc. The bottom lie of the displa shows the sigal stregth ad also which zoe/user the device is mapped to. Sigal stregth should be greater tha 30. The sigal rage is betwee 0 ad 90 Deletig Devices To delete radio devices, select the device umber to be deleted the follow the procedure for learig a ew device but press the butto o the kepad whe prompted to activate device istead of activatig the tamper switch. INS

122 Egieer Utilities Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Ricochet Diagostics (MT2 Ol) This meu displas iformatio about the live sstem, ad is split ito Premier Elite SmartKe ad Ricochet devices via Zoes ad Users. Example Zoe 009 _OEB Shock I this example Zoe 9 ca see the devices as detailed below, use the scroll ke to view iformatio about other devices:- Devices For Devices the followig iformatio ca be viewed:- Routeig RSSI Alarms ad Status Device visibilit Time sice last message Premier Elite SmartKe For Premier Elite SmartKe the followig iformatio ca be viewed:- Routeig RSSI Premier Elite SmartKe Butto Status Iterpretig Kepad Displas Routeig The image below shows that Zoe 009 is routeig through 14 ad the 7 to the expader, for Premier Elite SmartKe this ma var depedig o where & whe the readig is take. If questio marks appear i the displa it meas the iformatio is ot available. Zoe 009 PIR ->014->007->XP RSSI Each value i the image below represets the RSSI levels i dbm at each of the hops. If questio marks appear o the displa it meas the iformatio is ot available. Zoe 009 PIR 69>> 80>> XP If questio marks appear it could be because either the sstem has just bee powered up ad iformatio has ot bee collected et, or o large sstems the iformatio is ot i memor. To populate the displa activate the device ad the iformatio should appear. Device Messages Zoe 001 Not Ricochet Zoe 009 PIR Msg??? mis ago Zoe 009 PIR >1hr sice msg Zoe 009 PIR No msg recvd et Sigal Securit Zoe 009???? Shock The chose zoe does ot have a Ricochet device leared to it. shows the last time the device commuicated this represets the last message ad could be a poll, activatio or tamper etc... This is a warig showig that the last commuicatio from the device was over a hour ago. This displa shows that o message has bee received et, this would ormall be see o a recetl powered up sstem, wait 15 miutes from power up before checkig the diagostics iformatio. This displa shows iformatio relatig to sigal securit o a 8XP-W. 4 widows are available to show iformatio; each widow represets two devices, (Odd & Eve device slots). Each widow could show a of the iformatio detailed i the table below Displa Device Ca see O the 32XP-W there are 16 widows to show iformatio from the 32 devices of the sstem; the format is the same. Device Status Zoe 009 Shock Status: aaaspdtt Secure/OK Active/Fault Tpe a A Mag1 a A Mag2/Sho a A Reed/PIR s S Poll/Supervisio p P Power/Batter d D Device t T Rear t T Frot Premier Elite SmartKe Messages User000 Ricochet Not Ricochet User002 Ricochet Not coected User002 Ricochet Logo Bat OK User002 Ricochet Partarm Bat OK User002 Ricochet Disarm Bat OK User002 Ricochet Fullarm Bat OK User002 Ricochet Aux? Bat OK User002 Ricochet Paic Bat OK YES to erase ukow kefobs The chose user does ot have a Premier Elite SmartKe associated with them. The Premier Elite SmartKe is ot switched o Shows the batter is OK ad the fob has logged oto the sstem. Shows the differet messages displaed whe the relevat buttos are pressed. Shows which Aux butto has bee pressed whe i Fuctio Mode. Shows the Paic fuctio has bee activated Use this optio ONLY if the pael has bee replaced ad ot all Premier Elite SmartKe are recogised b the ew pael, or if the error toe is heard whe learig ew Premier Elite SmartKe This optio DOES NOT remove kow Premier Elite SmartKe, use the Delete optio i Setup Users.? No iformatio is available _ The chose device caot see either of the devices O The chose device ca see the ODD device(s) E The chose device ca see the EVEN device(s) B The chose device ca see BOTH devices 122 INS176-9

123 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Egieer Utilities Ricochet Diagostics Meu Egieer Utils Egieer Utils View Evet Log U Zoe 001 Not Ricochet? Use U to scroll to R ic oc he t Diag O Eter the Zoe/User Number to view User000 Ricochet Not Ricochet? R YES to erase ukow kefobs Zoe 009 Shock ->???->???->XP C Zoe 009 Shock??>>??>>??@ XP C Zoe 009 Shock Status: aaaspdtt C Zoe 009 Shock???????????????? C User002 Ricochet Not coected User002 Ricochet ->XP C User002 Ricochet -99>>@ XP C User002 Ricochet Logo Bat OK C Tur o S ma rtke Zoe 009 Shock >1hr sice msg C INS

124 Programmig Part Arms Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 5.10 Programmig Part Arms Alter Part Arms Zoe Setup P Alter Part Arms P For Part Arm 1 Zoe 001 is > ON C For Part Arm 2 Zoe 001 is > ON? For Part Arm 2 Zoe 010 is > ON For Part Arm 2 Zoe 010 is >OFF Pre s s O MIT to s e lect Part Arm 1 Press CHIME to select Part Arm 2 Press PART to select Part Arm 3 e.g. CHIME = Part Arm 2 Use kes 0-9 to eter the required zoe umber or use the S C RO LL k e to sea rch e.g. 064 = Zoe 10 Pre s s N O to tur the zoe O or Off for the selected Part Arm Each area o the sstem ca have up to 3 Part Arms. Whe Part Arm 1, 2 or 3 is selected, pre-programmed zoes are omitted to allow access to certai parts of the buildig. 124 INS176-9

125 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Stadards 6. Specificatios Cotrol Paels Idetifig the Cotrol Pael Tpe Code Descriptio AEO Premier 24 AEJ Premier 48 AFG Premier 48-W 868MHz AFN Premier 48-W 433MHz AEK Premier 88 AEL Premier 168 AEZ Premier 640 Premier Elite 24 (Polmer) Curret Curret Cosumptio 95mA Maximum Curret Available 0.3A charge 1.1A Rated Output Batter Rated Output (Amps) 12h Batter Arragemet Charge 1 x 7Ah 0.3A 0.48A Stadb ad Recharge Times EN Grade 1 Grade 2 Miimum Stadb Period 12h 12h Maximum Recharge Time 72 Hrs 72 Hrs PD6662 Grade 1 Grade 2 Stadb Period 12 Hrs 12 Hrs Maximum Recharge Time 72 Hrs 72 Hrs Power Suppl Rated Iput: Rated Output 55 C:: Tpe A 100V - 50/60Hz; 1A 1.5A MAX Rated Output Voltage: 13.&Vdc +/- 2% Mais Termial Block Fuse: 250Vac; A Slow/Medium Blow Maximum ratig of each power output (ote that these are ot cosidered to be "idepedet power outputs" accordig to EN Aux 12V 1.0A Bell/Strobe 1.0A Network 1 1.0A Batter 1.6A DC+/DC- 1.0A Stadb Curret 95mA Output Voltage Rage: 13.0V to 13.9V Maximum Ripple Voltage: 0.5V pk-pk Batter tpe: sealed lead acid, up to 7Ah, Maximum recharge time 72h Batter Low Voltage Sigal: 9.5V Power Output Fault sigal: 10.5V (with mais preset) Deep Discharge protectio: 8.1V Over voltage protectio trigger: 16V Fuses F1 (900mA) Auxiliar 12V Power fuse (electroic PTC) F2 (900mA) Digicom Power (electroic PTC) F3 (900mA) Network 1 fuse (electroic PTC) F4 (900mA) Bell/Strobe fuse (electroic PTC) F6 (1.6 Amp) Batter fuse (electroic PTC) Housig Dimesios (W x H x D) Batter Compartmet Packed Weight Premier Elite 24 (Metal) Curret Curret Cosumptio 3mm Polcarboate 305mm x 263mm x 98mm Oe 12V 7.0Ah batter 1.5 Kg (Approx) 95mA Maximum Curret Available 0.75A charge 1.0A 0.3A charge 1.9A Rated Output Batter Batter Rated Output (Amps) Arragemet Charge 12h 24h 30h 60h 1 x 7Ah 0.3A 0.48A 0.19A 0.13A 0.021A 1 x 17Ah 0.3A 1.32A 0.61A 0.47A 0.18A 0.75A 1.0A 0.61A 0.47A 0.18A Stadb ad Recharge Times EN Grade 1 Grade 2 Grade 3 Miimum Stadb Period 12h 12h 30h * Maximum Recharge Time 72 Hrs 72 Hrs 24 Hrs PD6662 Grade 1 Grade 2 Grade 3 Stadb Period 12 Hrs 12 Hrs 24 Hrs ** Maximum Recharge Time 72 Hrs 72 Hrs 24 Hrs *30h if MAINS FAIL is reported to ARC, otherwise 60h **This time ma be halved if mais failure is sigalled to a ARC Jumper Settigs Batter Arragemet Recharge Time Batter Charge Selector 1 x 7Ah < 24Hrs 0.3 A 1 x 17Ah < 24Hrs 0.75 A < 72Hrs 0.3 A Power Suppl Tpe A Rated Iput: Rated Output Curret@40 C: 220V - 1A 2.5A MAX Rated Iput: Rated Output Curret@40 C: 100VV - 1A 2.3A MAX Rated Output Voltage: 13.&Vdc +/- 2% Mais Termial Block Fuse: 250Vac; A Slow/Medium Blow Maximum ratig of each power output (ote that these are ot cosidered to be "idepedet power outputs" accordig to EN Aux 12V Bell/Strobe Network 1 Batter DC+/DC- 1.0A 1.0A 1.0A 1.6A 1.0A Stadb Curret 95mA Output Voltage Rage: 13.0V to 13.9V Maximum Ripple Voltage: 0.5V pk-pk Batter tpe: sealed lead acid, up to 18Ah, Maximum recharge time 24h (0.75A charge rate) 72h (0.3A charge rate) Batter Low Voltage Sigal: 9.5V Power Output Fault sigal: 10.5V (with mais preset) Deep Discharge protectio: 8.1V Over voltage protectio trigger: 16V Fuses F1 (900mA) Auxiliar 12V Power fuse (electroic PTC) F2 (900mA) Digicom Power (electroic PTC) F3 (900mA) Network 1 fuse (electroic PTC) F4 (900mA) Bell/Strobe fuse (electroic PTC) F6 (1.6 Amp) Batter fuse (electroic PTC) Housig Dimesios (W x H x D) Batter Compartmet Packed Weight Premier Elite 48-W Curret Curret Cosumptio Maximum Curret Available 1mm Mild Steel 315mm x 415mm x 100mm Up tp oe 18Ah batter 4.5 Kg (Approx) INS mA

126 Specificatios Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual 0.3A charge 1.0A Rated Output Batter Rated Output (Amps) 12h Batter Arragemet Charge 1 x 7Ah 0.3A 0.433A Stadb ad Recharge Times EN Grade 1 Grade 2 Miimum Stadb Period 12h 12h Maximum Recharge Time 72 Hrs 72 Hrs PD6662 Grade 1 Grade 2 Stadb Period 12 Hrs 12 Hrs Maximum Recharge Time 72 Hrs 72 Hrs Power Suppl Rated Iput: Rated Output 55 C:: Tpe A 100V - 50/60Hz; 1A 1.5A MAX Rated Output Voltage: 13.&Vdc +/- 2% Mais Termial Block Fuse: 250Vac; A Slow/Medium Blow Maximum ratig of each power output (ote that these are ot cosidered to be "idepedet power outputs" accordig to EN Aux 12V 1.0A Bell/Strobe 1.0A Network 1 1.0A Batter 1.6A DC+/DC- 1.0A Stadb Curret 150mA Output Voltage Rage: 13.0V to 13.9V Maximum Ripple Voltage: 0.5V pk-pk Batter tpe: sealed lead acid, up to 7Ah, Maximum recharge time 72h Batter Low Voltage Sigal: 9.5V Power Output Fault sigal: 10.5V (with mais preset) Deep Discharge protectio: 8.1V Over voltage protectio trigger: 16V Fuses F6 PTC (0.9A) Auxiliar 12V Power fuse F4 PTC (0.9 A) Network 1 fuse F5 PTC (0.9 A) Bell/Strobe fuse Housig Dimesios (W x H x D) Batter Compartmet Packed Weight Premier Elite 48/88/168 Curret Curret Cosumptio 125mA Maximum Curret Available 0.75A charge 1.0A 0.3A charge 1.9A Rated Output Batter 3mm Polcarboate 305mm x 263mm x 98mm Oe 12V 7.0Ah batter 1.7 Kg (Approx) Rated Output (Amps) 12h 24h 30h 60h Batter Arragemet Charge 1 x 7Ah 0.3A 0.458A 0.166A 0.108A 1 x 17Ah 0.3A 1.29A 0.583A 0.441A 0.158A 0.75A 1.0A 0.583A 0.441A A Stadb ad Recharge Times EN Grade 1 Grade 2 Grade 3 Miimum Stadb Period 12h 12h 30h * Maximum Recharge Time 72 Hrs 72 Hrs 24 Hrs PD6662 Grade 1 Grade 2 Grade 3 Stadb Period 12 Hrs 12 Hrs 24 Hrs ** Maximum Recharge Time 72 Hrs 72 Hrs 24 Hrs *30h if MAINS FAIL is reported to ARC, otherwise 60h **This time ma be halved if mais failure is sigalled to a ARC Jumper Settigs Batter Arragemet Recharge Time Batter Charge Selector 1 x 7Ah < 24Hrs 0.3 A 1 x 17Ah < 24Hrs 0.75 A < 72Hrs 0.3 A Power Suppl Tpe A Rated Iput: Rated Output Curret@40 C: 220V - 1A 2.5A MAX Rated Iput: Rated Output Curret@40 C: 100VV - 1A 2.3A MAX Rated Output Voltage: 13.&Vdc +/- 2% Mais Termial Block Fuse: 250Vac; A Slow/Medium Blow Maximum ratig of each power output (ote that these are ot cosidered to be "idepedet power outputs" accordig to EN Aux 12V Bell/Strobe Network 1 & 2 Batter DC+/DC- 1.0A 1.0A 1.0A 1.6A 1.0A Stadb Curret 125mA Output Voltage Rage: 13.0V to 13.9V Maximum Ripple Voltage: 0.5V pk-pk Batter tpe: sealed lead acid, up to 18Ah, Maximum recharge time 72h Batter Low Voltage Sigal: 9.5V Power Output Fault sigal: 10.5V (with mais preset) Deep Discharge protectio: 8.1V Over voltage protectio trigger: 16V Fuses F1 (1Amp) Auxiliar 12V Power fuse F2 (1.6 Amp) Batter fuse (electroic PTC) F3 (1 Amp) Network 1 fuse F4 (1 Amp) Bell/Strobe fuse F5 (1 Amp) Network 2 fuse (168 ol) Housig Dimesios (W x H x D) Batter Compartmet Packed Weight Premier Elite 640 Curret Curret Cosumptio 125mA Maximum Curret Available 0.75A charge 1.0A Rated Output Batter 1mm Mild Steel 315mm x 415mm x 100mm Up tp oe 18Ah batter 4.5 Kg (Approx) Batter Rated Output (Amps) Arragemet Charge 12h 24h 30h 60h 1 x 17Ah 0.75A 1.0A 0.558A 0.416A 0.133A Stadb ad Recharge Times EN Grade 1 Grade 2 Grade 3 Miimum Stadb Period 12h 12h 30h * Maximum Recharge Time 72 Hrs 72 Hrs 24 Hrs PD6662 Grade 1 Grade 2 Grade 3 Stadb Period 12 Hrs 12 Hrs 24 Hrs ** Maximum Recharge Time 72 Hrs 72 Hrs 24 Hrs *30h if MAINS FAIL is reported to ARC, otherwise 60h **This time ma be halved if mais failure is sigalled to a ARC Power Suppl Tpe A Rated Iput: 220V - 1A Rated Output Curret@40 C: 2.5A MAX Rated Iput: 100VV - 1A Rated Output Curret@40 C: 2.3A MAX Rated Output Voltage: 13.&Vdc +/- 2% Mais Termial Block Fuse: 250Vac; A Slow/Medium Blow Maximum ratig of each power output (ote that these are ot cosidered to be "idepedet power outputs" accordig to EN Aux 12V 1.0A Bell/Strobe 1.0A Network 1 & 2 1.0A Batter 1.6A DC+/DC- 1.0A Stadb Curret 150mA Output Voltage Rage: 13.0V to 13.9V 126 INS176-9

127 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Maximum Ripple Voltage: 0.5V pk-pk Batter tpe: sealed lead acid, up to 18Ah, Maximum recharge time 72h Batter Low Voltage Sigal: 9.5V Power Output Fault sigal: Deep Discharge protectio: 8.1V Over voltage protectio trigger: Fuses (Electroic PTC) Housig Dimesios (W x H x D) Batter Compartmet Packed Weight Geeral (All Models) Data Network Remote Kepads 24 &48 & 48-W Expaders & 48-W Output Modules & 48-W Zoes W EOL Resistor Values EOL Resistor Cotact Resistor Fault Resistor 0-1k 1k1 to 4k 4k1 to 5k6 5k7 to 8k 8k1 to 20k (30k) 21k+ (30k+) Digicom Outputs Outputs 1 to 8 Pael Outputs PG1 (24 ol) Outputs 1 & 2 (48/88/168) Outputs 3 & 4 (88/168) Output 5 (88/168) 10.5V (with mais preset) 16V F3 (1600 ma) Batter F4 (250mA) Speaker F5 (900mA) Network 1 F6 (900mA) Bell/Strobe F7 (900mA) Network 2 F8 (900mA) Network 3 F9 (900mA) Network 4 F10 (900mA) Network 5 F11 (900mA) Network 6 F12 (900mA) Network 7 F13 (900mA) Network 8 F14 (900mA) Auxiliar 12V 1mm Mild Steel 315mm x 415mm x 100mm Up tp oe 18Ah batter 4.5 Kg (Approx) 4-wire stadard 7/0.2 alarm cable up to 500m Star, Dais Chai or a combiatio of the two Up to 4 Up to 8 Up to 16 Up to 64 Up to 2 Up to 4 Up to 8 Up to 16 Up to 64 1 Up to 2 Up to 4 Up to 8 Up to 32 8 expadable to 24 8 expadable to 48 4 expadable to 48 8 expadable to 88 8 expadable to expadable to 640- (Alteratives Available) 2k2 (3k3) 4k7 (3k3) 2k2 Zoe Short Zoe Secure Zoe Fault Zoe Active Zoe Mask Zoe Tamper 100mA switched to 0V 100mA -ve 500mA switched to 0V 500mA switched to 12V 3 Amp Rela Sire Outputs Bell Trigger Strobe Trigger Speaker Output Evirometal (All Models) Operatig Temperature Storage Temperature Maximum Humidit EMC Eviromet Ihibit Fuctios 1A switched to 0V 1A switched to 0V Miimum load 8Ω -10 C to +40 C -20 C o +60 C 95% o-codesig Residetial Commercial Light Idustrial Idustrial Stadards For Alarms ad Tamper is cotrolled b the Swiger shutdow couter which is programmable ad is defaulted to 3.Please see page 46 ad 69. Miimum Logical Kes 10,000 for 4 digit code* 100,000 for 5 digit code* 1,000,000 for 6 digit code* The umber of disallowed codes = 0* User codes must be programmed as a 6 digit code to compl with INCERT. Depedat o the use of the Black Listed codes fuctio available via Witex, a maximum of 16 codes ma be Black Listed Calibratio Checks & Adjustmets There are o calibratio checks or adjustmets available o the cotrol pael. Sigal & Message Processig Idicatios First alarm idicatios followed b a other evets durig the set period will scroll ad ca be cotrolled b the ke o the kepad. Memor Support A memor support batter is ot required. Compliace Label If the alarm sstem is programmed to NOT coform with EN or EN or is istalled to Grade 1 the compliace label MUST be removed. Egieer Access Global Optios/Sstem Cofiguratio Optio 10 see page 64 set to Egieer ol EN50131 ad User + Egieer for PD6662. Microprocessor Idetificatio Premier Elite 24/48/88/168 Premier Elite LC256I/P 25LC1024I/P INS

128 Specificatios Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Remote Kepads Electrical Operatig Voltage VDC ACE Tpe B Curret Cosumptio without Prox Quiescet (Not Backlit) 25mA Alarm (Not Backlit) 45mA Full Backlit 100mA Alarm + Full Backlit 145mA Curret Cosumptio with Prox Quiescet (Not Backlit) 85mA Alarm (Not Backlit) 105mA Full Backlit 185mA Alarm + Full Backlit 205mA Data Network 4-wire stadard 7/0.2 alarm cable up to 500m Star, Dais Chai or a combiatio of the two Kepad Tpe LCD 32 Character LCD LCDL 32 Character large LCD LCDP LCD + Prox Reader LCDLP LCDL + Prox Reader Zoes 2 EOL Resistor Values (Alteratives Available) EOL Resistor 2k2 (3k3) Cotact Resistor 4k7 (3k3) Fault Resistor 2k2 0-1k Zoe Short 1k1 to 4k Zoe Secure 4k1 to 5k6 Zoe Fault 5k7 to 8k Zoe Active 8k1 to 20k (30k) Zoe Mask 21k+ (30k+) Zoe Tamper Output 100mA switched to 0V Back Lightig Full adjustable Speaker Output (LCDL/LCDLP) Miimum load 8Ω Speaker Volume (LCDL/LCDLP) Full adjustable Proximit Reader (LCDP/LCDLP) Tag Evirometal Operatig Temperature Storage Temperature Maximum Humidit EMC Eviromet -10 C (+14 F) to +55 C (+131 F) -20 C (-4 F) to +60 C (+140 F) 95% o-codesig Residetial Commercial Light Idustrial Idustrial Zoes 8XP 60IXD EOL Resistor Values EOL Resistor Cotact Resistor Fault Resistor 0-1k 1k1 to 4k 4k1 to 5k6 5k7 to 8k 8k1 to 20k (30k) 21k+ (30k+) Outputs Outputs 1 & 2 (4XP) Outputs 1-8 (8XP) Speaker Output (4XP & 8XP) Evirometal Operatig Temperature Storage Temperature Maximum Humidit EMC Eviromet Phsical Dimesios (W x H x D) Packed Weight Output Expaders Electrical Operatig Voltage ACE Tpe Curret Cosumptio Quiescet Alarm (Nothig Coected) Network Bak 1 Outputs Outputs 1 to 8 Bak 2 Outputs Outputs 1 to 8 a combiatio of the two 8 DP or EOL zoes 60 id zoes (2 loops) (Alteratives Available) 2k2 (3k3) 4k7 (3k3) 2k2 Zoe Short Zoe Secure Zoe Fault Zoe Active Zoe Mask Zoe Tamper 100mA switched to 0V 100mA switched to 0V Miimum load 8Ω -10 C (+14 F) to +55 C (+131 F) -20 C (-4 F) to +60 C (+140 F) 95% o-codesig Residetial Commercial Light Idustrial Idustrial 170mm x 140mm x 35mm 200g Approx VDC B 65mA 65mA 4-wire stadard 7/0.2 alarm cable up to 250m Star, Dais Chai or a combiatio of the two 100mA switched to 0V 100mA switched to 0V Phsical Evirometal Dimesios (W x H x D) Packed Weight Zoe Expaders Electrical Operatig Voltage ACE Tpe 145mm x 115mm x 30mm 260g Approx VDC B Operatig Temperature Storage Temperature Maximum Humidit EMC Eviromet -10 C (+14 F) to +55 C (+131 F) -20 C (-4 F) to +60 C (+140 F) 95% o-codesig Residetial Commercial Light Idustrial Idustrial Curret Cosumptio 4XP 8XP Quiescet Alarm (Nothig Coected) Data Network 65mA 65mA 4-wire stadard 7/0.2 alarm cable up to 500m Star, Dais Chai or Phsical Dimesios (W x H x D) Packed Weight 170mm x 140mm x 35mm 200g Approx. 128 INS176-9

129 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Stadards Stadards 2004/108/EC (CE directive): Hereb, Texecom declares that this device is i compliace with the essetial requiremets ad other relevat provisios of Directive 2004/108/EC. Weee Directive: 2002/96/EC (WEEE directive): Products marked with this smbol caot be disposed of as usorted muicipal waste i the Europea Uio. For proper recclig, retur this product to our local supplier upo the purchase of equivalet ew equipmet, or dispose of it at desigated collectio poits. For more iformatio see: RoHs Directive: 2002/95/EC RoHS Compliat. Hereb, Texecom declares that this device does ot cotai lead, mercur, cadmium, hexavalet chromium, polbromiated biphels (PBB) or polbromiated dephe ethers (PBDE) i more tha the percetage specified b EU directive 2002/95/EC, except exemptios stated i EU directive 2002/95/EC aex. This product is suitable for use i sstems desiged to compl with EN , EN ad PD6662 at Grade 3 ad Evirometal Class II. Warrat All Texecom products are desiged for reliable, trouble free operatio. Qualit is carefull moitored b extesive computerised testig. As a result the cotrol pael is covered b a two-ear warrat agaist defects i materials or workmaship. As the cotrol pael is ot a complete alarm sstem but ol a part thereof, Texecom caot accept resposibilit or liabilit for a damages whatsoever based o a claim that the cotrol pael failed to fuctio correctl. Due to our polic of cotiuous improvemets Texecom reserve the right to chage specificatio without prior otice. Kepads ad Expaders are protected b UK & Iteratioal Registered Desig. Registered Desig Numbers: ad Premier & Premier Elite are trademarks of Texecom. INS

130 Notes Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Notes: 130 INS176-9

131 Premier Elite 24,24-W, 48,48-W, 88, 168 & 640 Istallatio Maual Notes Notes INS

132 Texecom Limited, Bradwood Court, St. Crispi Wa, Hasligde, Lacashire BB4 4PW, Eglad. Techical Support: UK Customers Tel: (Calls charged at local rate from a BT ladlie. Calls from other etworks ma var.) Iteratioal Customers Tel: [email protected] Texecom Limited 2012 INS176-9