Blind rivet VENTILATION

Transcription

1 Length Sheet thread Self-drilling screws DIN 7504, with hexagonal head, for the attachment of air pipes, ducts, spiral-seam pipes, without pre-drilling, galvanised Screw head Ø Spanner size S pieces carton* *) 12 boxes of 500 pieces in a carton. Length Sheet thread Screw head Ø Self-drilling screws with building regulation approval, for attachment on trapezoid sheet according to approval Z , galvanised Spanner size S pieces VENTILATION Blind rivet For the attachment of duct fixing angles and brackets on air ducts and spiral-seam tubes respectively Blind rivet with large surface in order to secure various materials No surface damaging after riveting No loosening by dynamic influences (vibration resistant) Good behaviour at temperature fluctuations High-quality, simple and quick mounting Type Material sleeve Material mandrel Dimensions D1 L E D2 K W flat round head aluminium steel pieces 3, ,5 5, , ,0 6, , ,0 9, /10

2 ACCESSORIES Punched tapes galvanised or plastic coated Efficient punched tape for simple fastening jobs Easy to handle due to versatile mounting accessories Can be fitted with DÄMMGULAST Junior vibration control lining Type Tape width b Tensile breaking strength Max. recommended load Straight edges, galvanised 17 2, Corrugated edges, galvanised 12 1, ,200 1, ,750 2,250 Plastic coated 19 3,300 1, ,900 1,300 Type Tape width b Hole diameter D Hole spacing C Length of roll [m] Straight edges, galvanised roll Corrugated edges, galvanised Plastic coated ! Rolls of 50 m are supplied in a practical dispenser case. Connecting thread Screw length Bolts with nuts M pieces M M For thread Washers M pieces M Bolts with nuts and washers for punched tapes, galvanised 5/17

3 ACCESSORIES Distance angles galvanised Leg length L pieces For attachment of flat and ribbed radiators Fast and secure installation Can also be used as bracket and holder Height adjustment up to 30 mm Horizontal adjustment of 45 to 65 mm Horizontally adjustable from 65 to 85 mm, if the bracket legs are reversed Vibration isolated due to rubber inlay Radiator mounting angle galvanised Produktleistungen Montagestellung Mounting position Verformung Deformation bei at Breaking Bruchfestigkeit strength Langer Long bar Steg on the an der wall, Wand, slider Schieber is retracted eingefahren ,100 Langer Long bar Steg on the an der wall, Wand, slider Schieber is extended ausgefahren Kurzer Short bar Steg on an the der wall, Wand, slider Schieber is retracted eingefahren Kurzer Short bar Steg on an the der wall, Wand, slider Schieber is extended ausgefahren pieces 5/23

4 HOT-DIP GALVANISED PRODUCTS DÄMMGULAST Channel sections for MPC-Profiles Ideal for the decoupling of traverses for air duct fixtures For secure vibration-decoupling of MPC-Support channels Easy installation by inserting into MPC-Support channels and/or screwing onto threaded rods Prevents structure-borne noise coupling by avoiding contact between the air duct and the threaded rods Interlocking profile prevents channel section being pushed out Prevents fluttering and other vibration noises in the air ducts Small contact surface, large absorption mass Vibration control Design For support channels Suitable for 27/18, 28/30 Channels with slot widths of mm, roll M8 threaded rods 38/40, 39/52, 40/60, Channels with slot widths of mm, /80, 38/80, 40/120 M8 and M10 threaded rods pieces DÄMMGULAST Channel section roll of 30 m DÄMMGULAST Channel sections section of 50 mm DÄMMGULAST Channel sections section of 100 mm ! When installing air conditioning and ventilation equipment, MPC-Support channels can be used as load-bearing traverses. Structure-borne vibration coupling bridges resulting from direct metal contact between the air duct and the traverse or threaded rods can be prevented by the use of DÄMMGULAST Channel section as intermediate layer. The DÄMMGULAST Channel section was developed especially for these application areas and provides the optimum solution from a practical installation point of view. 12/12

5 SUPPORT CHANNELS MPC-Wall hanger supports without vibration control, galvanised For wall mounting of air-conditioning units where no vibration damping is required Galvanised version for use in dry interiors Efficient mounting due to preassembled parts MPC-Support channels cut-to length and with holes on the rear side including MPC-Protection caps Various bracket lengths available (depending on device type) Simple height adjustment of the brackets due to sliding MPC- Hammer head bolts Variable adjustment of the mounting spaces on the bracket due to MPC-Rail nuts Length L Max. recommended load (set) 480 1, , ,900 Complete kit consists of: 2 MPC-Support channels 38/40, length 520 mm 2 MPC-Wall hanger brackets 38/40 6 MPC-Protection caps for 38/40 profile 4 MPC-Hammer-head bolts M10/30 4 Washers 8.5 x 36 x 2 mm 4 MPC-Rail nuts M8 for 38/40 profile 4 Hexagon head bolts M8/20 4 MPC-Clamp brackets M10 for 38/40 profile Length L set /13

6 VENTILATION Duct fixing bracket For vibration-isolated suspension of round and rectangular air ducts Versatile application options, e. g. on trapezoidal corrugated metal sheeting for the suspension of MPC-Support channels DÄMMGULAST Spring element integrated in the duct fixing bracket Average vibration reduction of 16 db(a) Ideal adaptation to all duct diameters and cross-sections due to pre-determined bending points Simple attachment to the air duct with rivets or self-drilling screws Suspension of the duct fixing bracket from threaded rods or direct attachment to the structure Max. recommended load 230 Vibration control pieces 9/6

7 VENTILATION Duct fixing bracket Rectangular duct attached to the ceiling with duct fixing brackets, threaded rods and steel anchors Air duct suspended from the ceiling with duct fixing bracket, steel tape or punched tape Direct attachment to trapezoidal corrugated steel sheet with a duct fixing bracket Vibration damped attachment of a MPC-Support channel to a wide trapezoidal corrugated sheet with a duct fixing bracket! The highly-elastic DÄMMGULAST Spring element is essential for efficient prevention of structure-borne vibration. The installation is carried out with threaded rods. This prevents vibration coupling between air pipe or air duct and the structure. The duct fixing bracket is attached to the air pipe or duct section with rivets or selfdrilling screws. 9/7

8 VENTILATION Easy to install suspension for air ducts Incorporated highly-elastic vibration-isolating element Excellent alignment and height adjustment via the threaded rods Design as angle and twin-angle Various attachment options to air duct with rivets, self-drilling screws or bolts up to M8 in the oblong hole Direct attachment to building structure possible Average vibration reduction of 17 db(a) Duct fixing twin-angles Vibration control Type Max. recommended load Average vibration reduction [db(a)] I II Type I Type II Duct fixing twin-angles Type I Duct fixing twin-angles Type II Duct fixing twin-angles Type I pieces II I II Rubber washers, single 12 x 24 x 4 mm x 24 x 6 mm ! and twin-angles are also available in other lengths. 9/8