BOQ FOR ELECTRICAL WORK OF HLST IN GROUND FLOOR AT S.B.I. LHO BHOPAL.

Transcription

1 BOQ FOR ELECTRICAL WORK OF HLST IN GROUND FLOOR AT S.B.I. LHO BHOPAL. Note: Use of Flexible conduits & Elbows in Circuit wiring is not allowed except in exceptional site conditions with the approval of Bank's Engineer / Architect and All wiring laying in the MS/PVC conduit strickly follow IE( Indian Electricity) rules and IE(Indian Electricity) rules follow in all items of project. Proper ferrules, lux, thimble to be done in all cabling and wiring from both load/source end. S.No. DESCRIPTION QTY UNIT RATE AMOUNT 1 ELECTRICAL WIRING Providing & fixing POINT WIRING for Ceiling and wall lights, Ceiling fan, wall fan, exhaust fan, Plug points Bell points. The item includes Circuit wiring from DB to the switch board with 3x2.5 Sq.MM PVC insulated copper conductor single core multistrended wire for Phase, Neutral & Earth (P+N+E) in appropriate size 20/25mm dia of 16 SWG wall thickness, MS medium conduits ( stove enamelled regid steel conduit) ISI mark (IS :9537), point wiring to be with 3x1.5 Sq.MM PVC insulated copper conductor with all necessary accessories, such as saddles etc. on surface or embedded in wall, chasing the walls and making the surface neat afterwards. Item includes 6 AMP switch, socket, etc. PHILIPS ELITE, MK / NORTH WEST & ANCHOR ROMA, with all base plates, covering plate Metal box of same make etc. complete. (EACH Circuit to take NOT MORE than 7-8 points) Flexible conduits & Elbows are not allowed. Flexible conduit use it must be joined by gland and check nut at both ends. Only FRLS wire to be used a) but One point controlled by one switch.(i.e. inclusive of mains wiring). 55 Nos. b) but 2 points to be controlled by one switch.(i.e. inclusive of mains wiring). 10 Nos c) 3 but for one Exhaust fan point Nos. d) 6 AMP socket point on same board 15 Nos. Providing and fixing point wiring with same specs as above but for CIELING FAN e) points with 1x 5pin 6Amp socket outlet to be provided at the location of fan (i.e. inclusive of mains wiring).one Switch and one no stepped electronic regulator ( two 7 Nos. Module Providing ) as and fixing point wiring with same specs as above but for WALL FAN points f) with 1x 5pin 6Amp socket outlet to be provided at the location of fan (i.e. inclusive of mains wiring). 10 Nos. 6/16 AMP power point with 3x 2.5 sq.mm. wire and 20 mm dia. 16 swg stove g) enameled rigid steel conduits with 1x 5pin 6/16 Amp socket outlet. No extra cost for wiring and conduits is payable (i.e. inclusive of mains wiring). 20 Nos. providing and fixing 6 Amps Plug Points with same specs as above but along with h) separate switchboard with 1x 5pin 6Amp socket outlet (separate point wring)(i.e. inclusive of mains wiring). 15 Nos Call bell point with call bell with 3x1.5 sq.mm. wire and 20 mm dia. 16 swg stove i) enameled rigid steel conduits. No extra cost for wiring and conduits is payable (i.e. inclusive of mains wiring). 5 Nos. j) SPECIAL POINTS : ( For Computers ) Supply, fixing, testing and commissioning of following Modular type switch socket with cover plate, PVC modular box on Surface / sheet steel box in concealed manner I/c electrical connections and making good all the damages, painting, cleaning the site etc complete as required as per site requirement and as directed.ups point with 3x 2.5 sq.mm. wire and 20 mm dia. 16 swg stove enameled rigid steel conduits. (i.e. inclusive of mains wiring). 2 Nos. 6/10A Switch + 3 Nos. 6/10A, 3 pin Socket 30 Nos. 2 A.C. point Supply, Installation, commissioning & Testing of the surface / recess mounting A.C. point as per above point wiring with 3x 4 sq.mm. PVC wiring in M.S. Conduit pipe, etc. with the followings : 32 A D.P.,1 way switch with neon with plate and box.- 1 set 25 A & 10 A Twin socket with plate and box.- 1 Set. i/c electrical connections and making good all the damages, painting, cleaning the site etc complete as required as per site requirement and as directed.(i.e. inclusive of mains wiring). 16 Nos. 3 MUSIC SYSTEM WIRING a) SPEAKERS supplying,installation,testing and commissioning 4 to 6 W speakers, off white High impact ABS plastic grill with spring loaded mounting clamps, good for mounting in false ceiling etc complete in all respect. 8 Nos b) PVC CONDUITS Supplying,laying /fixing of the following size conduit with conduit accessories like bend/junction box /on surface /floor /recees manner and making good all the damages,painting,cleaning the site etc complete as required. 20mm Dia. 1.6mm wall thickness rigid PVC conduits 110 RM c) SPEAKER WIRING Supplying,providing wiring (supply,fixing,testing and comm etc.),for light /power with following PVC insulated copper conductor,single core multi strended wire (HRFR ) in existing conduit including connections and making good all the damages,painting cleaning the site etc. complete as required as per the requirement and as directed 2x1.5 sqmm 130 RM

2 4 TELEPHONE POINT i) Supplying and fixing of krone telephone tag block, suitable for the multi core telephone cable and shall accommodate tin-plated phosphor bronze connectors, the connectors shall splice unskinned cables up to 0.61 mm dia and shall be terminate both incoming and out going lines, the tag blocks shall be mounted inside, water proof box and locking arrangement and shall be fully accessibie.the item is inclusive of providing and fixing of boxes in surface / recessed system etc complete as a. 20 Pair Tag Box 2 Nos ii) Supplying, Installation, testing and commissioning of the telephone point with the followings - a. Two pair, 0.50 mm dia. telephone cable tinned copper conductor, P.V.C. insulated and sheathed, fire retarding, anti termite, colour coded twisted pairs and rip cord. 350 Mtrs. b. Double outlet with shutter modular type Telephone Outlets ( RJ 11 ) with suitable size M.S./ PVC modular boxes complete as req. 30 Nos. iii) Supplying, Laying / Fixing of the following size conduit with conduit accessories like bend / junction box / fan box etc on surface / recessed manner and making and making good all the damages, painting, cleaning the site etc complete as required as per site requirement and as directed. a. 20 mm dia.1.6 mm wall thickness rigid PVC conduits. 120 Mtrs b. 25 mm dia.1.6 mm wall thickness rigid PVC conduits. 90 Mtrs. 5 Supply and fixing of 'S' type fan hook in the ceiling by cutting / chiesling, replastering, painting etc complete in all respect. 7 Nos. 6 Fitting and fixing of existing electrical equipments & fittings proper Installation, commissioning & Testing including required accessories, fastners and for fans hanging rods/pipes, ball sockets etccomplete as required as per site conditions. Light fittings in false ceiling/on wall/ceiling & all size of Ceiling Fans/wall fans/exhaust fan etc 10 Nos. 7 Dismentaling of all wirings, switch, sockets,dbs, Light fixtures & Fans etc.as per requirement at site. 1 Job 8 DISTRIBUTION BOARDS All MCB to be "C" series Supply, installation, commissioning & Testing of the surface/recess mounting following ways MCB DB's 230/415 Volts on surface/recessed, complete with tinned copper Busbar, Neutral Bar, Earth Bar, Din Bar detachable gland plate, interconnection and making good all the damages, painting, cleaning the site etc complete as required as per site requirement and as directed. A. LIGHT DISTRIBUTION BOARD : 1 Nos a. 1 no. TPN MCB DB 4 way ( ways ) b. 1 no TPN MCB 32 amp. 12 nos SP MCB 06 amp. c. B. POWER DISTRIBUTION BOARD : 1 Nos 1 no. TPN MCB DB 4 way ( ways ) a. b. 1 no TPN MCB 63 amp. c. 12 nos SP MCB 20/32 amp. C. U.P.S. POWER DIS.BOARD ( For UPS Out Goings ) : 1 Nos a. 1 no.spn MCB DB 12 way ( ways ) b. 1 no SPN MCB 32 amp. c. 10 nos SP MCB 10 amp. D. U.P.S. DISTRIBUTION BOARD ( for UPS IN PUT ) : 1 Nos. a. 63 A SPN MCB 1 no. b. 1 No Fabricated 18 swg m.s.box of suitable size OR factory made. E LOAD LINE DB ( Double door ) : 1 Nos. Supplying and fixing of following 4 Way three pole and neutral, sheet steel Vertical MCB distribution board, 415 volts on surface / recess,

3 complete with tinned copper busbar, neutral bar, earth bar, din bar, detachable gland plate with Cable termination box, interconnection including painting,earthing etc as required,with the followings - a 01 no. 125 amp., 10 KA, TP MCCB b 32 A TP MCB - 02 Nos. c 63 A TP MCB - 02 Nos. 9 LAN - ( LOCAL AREA NETWORKING ) FOR COMPUTERS : a Supply, Installation, Testing and Commissioning of 24 Port ( 100 base TX ) Cat-6 Patch / jack panel with connectors, outlets and necessary connectivity complete as 1 Nos. b Supply and Installation of following factory fabricated patch cords ( UTP-CAT 6 ) complete with connectors on both sides. i One Meter length. 30 Nos. ii Two Meter length. 30 Nos. c Supply and laying of Four Pair UTP CAT 6 LAN cables in existing PVC Conduit / Floor trunking with RJ-45 connector if required as per requirement. 490 Mtrs. d Supply and fixing of modular type Information Outlets with suitable size M.S./ PVC modular boxes complete with insulation displacement connectors etc suitable for CAT 6 UTP Cabling. i One Port. 30 Nos. e Supply, Installation, Testing and Commissioning of the following 10 / 100 Mbps Rack mounted Switch ( Auto managed ) suitable for auto-sense the network speed of the connected nodes to run at either 10 Mbps or 100 Mbps. The port also auto negotiate between full / half duplex and cable cross over. a). 24 RJ base T / 100 Base TX port. 1 Nos. f Supply, Installation, Testing and Commissioning of the following Rack on existing wall / table / plateform etc i/c fixing of equipment/ accessories etc as i 9 U Rack. 1 Nos. 10 CONDUITS Supplying, Laying / Fixing of the following size conduit with conduit, accessories like bend/junction box /fan box etc on surface/recessed manner and makingood all the damage painting,the site etc complete as per site requirement and as directed by Engg. In-Charge. a) 20 mm dia.pvc conduits. 180 RM b) 25 mm dia.pvc conduits. 160 RM 11 CABLING Supplying, unloading, storing, laying, testing and commissioning of following sizes of PVC /XLPE insulated (heavy duty)ai./ following sizes of PVC / XLPE insulated (Heavy duty) Al / Cu conductor armored cables suitable for working voltage up to armored cables suitable for working voltage upto and including 1100 volts,laid and tied on existing overhead cables trays or laid and tied over MS supports in Volts, laid and tied on existing overhead cable trays; or laid and tied over s in masonry trenches including providing MS including providing MS supports and clamps for fixing to supports ; or buried in ground complete as required as specifications required and as per specifications. a) 3.5 Core, 70 sq.mm Al. Cable.(main cable) 40 RM b) 4.0 Core, 25 sq.mm Al. Cable.(Power DB) 75 RM c) 4.0 Core, 10 sq. mm Al. Cable.(Light DB) 75 RM 12 CABLE END TERMINATION : ( 1100 V Gr.Cable ) Termination of the following sizes ( 4 / 3.5 core ) of XLPE insulated Aluminum conductor cable. Including providing terminal lugs single compression gland, crimping the joints, insulation tape effecting terminal connections to the equipment complete as required Up to 70 sq mm 10 Nos ELECTRICAL FAN AND FITTINGS 13 CEILING FANS Supply and fixing of the following ceiling fans. ( Brilliant white ) 1200 mm sweep 7 Nos. 14 WALL FANS Supply and fixing of the following wall fans. ( Brilliant white ) 400 mm sweep, 1300 rpm. 10 Nos.

4 15 EXHAUST FANS Supply and fixing of the 300 mm sweep exhaust fan with frame, Including making hole in the wall for fixing, and making good the civil damages etc as required 3 Nos. LED LIGHT FITTINGS 16 Supply, fixing,commissioning & testing of ceiling mounted Environment Friendly, Energy Efficient,decorative Square molded body Ceiling Mounted LED light Fixture with opel diffuser to give Glare free light with class-1 electrical safety, complete as 8 W-LED Light Fixture- Down Lighter 20 Nos. 17 Supply, fixing, commissioning & testing of ceiling/wall mounted Down Lighter Environment Friendly, Energy Efficient,decorative Round Ceiling Mounted LED light Fixture with with electronic driver for indoor applications with class I electrical safety, complete as 15 W- LED Light Fixture Down Lighter 4 Nos. 18 L E D TUBE LIGHT Supply, fixing, commissioning & testing of ceiling/wall mounted Environment Friendly, Energy Efficient,decorative Ultra Slim Linear light Fixture with extruded Aluminum heat Sink with class I electrical safety, complete as 20 W LED 4 0 Tube Light 6 Nos. 19 Supply of Energy efficient recess mounted 2'X2' ceiling mounted 36/38 watt LED light fixture with:- a) White powder coated Metallic CRCA housing. b) High-power, high efficiency LEDs (makes:cromptom/philips/syska/bajaj/havells make 25 Nos. 20 G.I.PLATE EARTH STATION : Preparation of the Plate Earth Station: (as per IS:3043) Excavation of rocky earth, soft murrum, hard murrum etc and back filling with black cotton soil for the earth station, the earth pit size is 1000 mm x 1000 mm x 2500 mm deep. S/F of G.I. plate of size 600 x 600 x 6.0 mm thick. fixing 50 mm x 6 mm, 3 mtrs G.I, strips from G.I.plate to earth terminal including brazing / welding at plate etc. Supplying and laying in position 19 mm, 2 mtrs G.I. `B' class pipe for watering.with reducer/funnel with mesh. S/F of the following in the earth station. 75 Kg. Charcoal. 15 Kg. Original Salt. Black Cotton soil Construction of earth pit chamber including necessary brick work concrete, plastering, S/F of C.I. Cover of size 12" x 12" complete as per site req. 1 No. 21 COPPER PLATE EARTH STATION : Preparation of the Plate Earth Station: (as per IS:3043) Excavation of rocky earth, soft murrum, hard murrum etc and back filling with black cotton soil for the earth station, the earth pit size is 1000 mm x 1000 mm x 2500 mm deep. S/F of Copper plate of size 600 x 600 x 3.0 mm thick. fixing 50 mm x 6 mm, 3 mtrs Copper strips from G.I.plate to earth terminal including brazing / welding at plate etc. Supplying and laying in position 19 mm, 2 mtrs G.I. `B' class pipe for watering.with reducer/funnel with mesh. S/F of the following in the earth station. 75 Kg. Charcoal. 15 Kg. Original Salt. Black Cotton soil

5 Construction of earth pit chamber including necessary brick work concrete, plastering, S/F of C.I. Cover of size 12" x 12" complete as per site req. 1 No. 22 i) Providing and fixing Copper / GI strip as per specification complete including connection to earth electrode revetting / sweating / soldering, burying 15 cms below in all types of soil / rocks etc complete as a G.I.Strip 25 X 5 mm 25 Mtrs. b G.I.Strip 50 X 6 mm 5 Mtrs. c Copper Strip 25 X 5 mm 25 Mtrs. d Copper Strip 50 X 6 mm 5 Mtrs. ii) Supply and laying of following size hot dip G.I.wire from earth terminal at earth station to earth bus-bar / pole etc.or with the Cable on wall / 150 mm below ground level,wherever required as per site condition. a 6 SWG G.I.Wire 40 Mtrs. b 10 SWG G.I.Wire 50 Mtrs. 23 Supply and laying of 16 sqmm PVC insulated copper wire in 15 mm G.I. pipe including accessories complete as 40 RM GRAND TOTAL Signature of Contractor (With Seal of Firm)