Preamble To Schedule A

Transcription

1 PRICE BID Page 1 of 6

2 Preamble To Schedule A 1) The quantities given in schedule A are purely for guidance of the contractor to enable him to quote the rates. The quantities can be varied to any extent, items can be omitted, added or substituted at the discretion or the company. The contractor is bound to execute any items required for completion of the job or contingent on the work. 2) The rates quoted are for complete items covering any minor details even if not detailed any unless other wise specified as exclusive. 3) No claim whatsoever will be entertained for idle labour or any delay in decisions /drawing etc. 4) Payment of running bills after submission, by the contractor with full supporting documents will be subject to satisfaction of Engineering and audit authorities of HAL. No claim what so ever on any delay in payment shall be admissible. 5) The contractor shall not stop/low down the progress of the work for want of decision on rates of deviation items and bound to maintain the progress of the work. The decision by Ch. Mgr (Plant Maint) interpretation of contract shall be final and binding on the contractor. 6) The decision by Ch. Mgr (Plant Maint) on extra /deviation items and their rates will be final and binding on the contractor. 7) Any error in units appearing in printed Schedule A such as M3 in place M2 or any such genuine mistake shall be subject to be corrected by Ch. Mgr ( Plant Maint) and binding on the contractor. 8) Any work contingent on the main work located in HAL premises will be considered as one work though the location of individual work may be away from each other. 9) Where there is duplicacy or any over lapping in schedule A items or any portion there of the contractor will execute after decision from E.I.C. & he will be paid once without any claim what so ever. 10) The rate quoted shall include execution of work according to MES SSR 2010 India / Bharat Standards for material /Workmanship and code of practices, sound engineering practice and as per direction of E.I.C. in order of preference. 11) The drawings shall be used progressively during the currency of the work as per site requirement. No claim what so ever on this account shall be entertained. 12) The drawing is subject to change /revision due to architectural /structural requirement etc. and working drawings shall be issued from time to time. 13) The contractor must deploy tradesman with proven performance and will take prior approval of Engineer in charge to his satisfaction before deployment. Page 2 of 6

3 SCHEDULE-A Sl No. Description Qty Unit Unit Quoted Rate 1 Supply of 20 pair jelly filled unarmored cable with 0.5mm 235 Mtrs. copper conductor, at new D type. 2 Supply of 5 pair jelly filled unarmored cable with 0.5mm 200 Mtrs. copper conductor, from new D type to gate no 1. 3 Supply of 100 pair telephone DB fitted with back mounting 1 No. frame and krone modules at new D type. 4 Supply of 20 pair telephone DB fitted with back mounting 2 No. frame and krone modules at new D type. 5 Supply of 10 pair telephone DB fitted with back mounting 1 No. frame and krone modules at gate no 1. 6 Supply of 100 mm G.I pipe at new D type 26 Mtrs. Amount In Rs. 7 Supply of 60 mm G.I pipe at new D type 2 Mtrs. 8 Supply of 25 mm G.I pipe at new D type 4 Mtrs. 9 Digging and refilling of 1 meter deep trench after laying of 498 Mtrs. side of cables and covered with bricks, from old D type to new D type. 10 Road drilling at 1 meter depth and inserting 100 mm G.I pipe 24 Mtrs. for laying the telephone cables at new D type. 11 Installation of 100 pair DB having UG cables (50 pair 20 pair 1 No. 5 pair) inserted in 60 mm GI pipe clamped properly on wall with clamp and saddle at new D type. 12 Installation of 20 pair DB having UG cables ( 20 pair) inserted 2 No. in 25 mm GI pipe clamped properly on wall with clamp and saddle at new D type. 13 Installation of 10 pair DB on a rectangular angle iron frame 1 No. (15mm x 1500mm) which is to be fixed on a 300mm deep brick foundation, having UG cables (5 pair) inserted in 25 mm GI pipe clamped properly on frame. Frame to be supplied by contactor, installation at gate no Punching of telephone cables (50 pair 20 pair 5 pair) at new 1 No. D type 100 pair DB and punching of 50 pair cable at old D type 600 pair DB. 15 Floor cutting up to 300mm depth (for cable laying) and 6 Mtrs. repairing of it properly after cable laying at new D type. 16 Supply of 10 pair jelly filled unarmored cable with 0.5mm 185 Mtrs. copper conductor, from auditorium crossing to gate no Supply of 10 pair telephone DB fitted with back mounting 1 No. frame and krone modules at gate no Supply of 40 mm G.I pipe at gate no Mtrs. 19 Supply of 25 mm G.I pipe at gate no.2. 2 Mtrs. Page 3 of 6

4 20 Digging and refilling of 1 meter deep trench after laying of 150 Mtrs. side of cables and covered with bricks, from auditorium crossing to gate. 21 Road drilling at 1 meter depth and inserting 100 mm G.I pipe 12 Mtrs. for laying the telephone cables. at gate no Installation of 10 pair DB having UG cables ( 5 pair) inserted 1 No. in 25 mm GI pipe clamped property on wall with clamp and saddle at gate no Punching of telephone cables (10 pair) at security post DB 1 No. at gate no Floor cutting up to 300mm depth (for cable laying) and 6 Mtrs. repairing of it properly after cable laying at gate no Cutting and repairing of drainage walls up to 500 mm depth 1 No. and fixing 40 mm G.I pipe for crossing the telephone cable through it at auditorium crossing. 26 Supply of 20 pair jelly filled unarmored cable with 0.5mm 190 Mtrs. copper conductor from gate no.4 to HAKS office. 27 Supply of 20 pair telephone DB fitted with back mounting 1 No. frame and krone modules at HAKS office. 28 Supply of 25 mm G.I pipe at HAKS office. 2 Mtrs. 29 Digging and refilling of 1 meter deep trench after laying of 177 Mtrs. side of cables and covered with bricks, from gate no.4 to HAKS office. 30 Installation of 20 pair DB having UG cables ( 20 pair) inserted 1 No. in 25 mm GI pipe clamped properly on wall with clamp and saddle at HAKS office. 31 Punching of telephone cables (20 pair) at HAKS office. 1 No. 32 Floor cutting up to 300mm depth (for cable laying) and 1 Mtrs. repairing of it properly after cable laying at HAKS office. 33 Supply of 10 pair jelly filled unarmored cable with 0.5mm 200 Mtrs. copper conductor from Marketing center to Civil maintenance building. 34 Supply of 10 pair telephone DB fitted with back mounting 2 No. frame and krone modules at Civil maintenance building. 35 Supply of 25 mm G.I pipe at Civil maintenance building. 11 Mtrs. 36 Digging and refilling of 1 meter deep trench after laying of 162 Mtrs. side of cables and covered with bricks, from Marketing center to Civil maintenance building. 37 Road drilling at 1 meter depth and inserting 25 mm G.I pipe 6 Mtrs. for laying the telephone cables at marriage hall crossing. 38 Additional rate of road cutting and repairing to digging and refilling of 1 meter deep trench after laying of UG cables with 1 inch cushion of sand to upper and lower side of cables and covered with bricks at marriage hall crossing. 13 Mtrs. Page 4 of 6

5 39 Installation of 10 pair DB having UG cables ( 10 pair) inserted in 25 mm G.I pipe clamped properly on wall with clamp and saddle at Marketing center to Civil maintenance building. 40 Punching of telephone cables (10 pair) at Marketing DB and Civil maintenance DB. 41 Floor cutting up to 300mm depth (for cable laying) and repairing of it properly after cable laying at Marketing center to Civil maintenance building. 42 Cutting and repairing of drainage walls up to 500 mm depth and fixing 25 mm G.I pipe for crossing the telephone cable through it at Marketing center to Civil maintenance building. 43 Floor cutting up to 300mm depth (for cable laying) and repairing of it properly after laying cable. 44 Cutting and repairing of drainage walls up to 500 mm depth and fixing 25 mm G.I pipe for crossing the telephone cable through it at gate no.6 45 Digging and refilling of 1 meter deep trench after laying of side of cables and covered with bricks at process shop. 46 Laying of 50 pair cable on the roof or corridor between process shop and Su-30 building with the help of clamp and saddles fixed 800 mm apart. 47 Entering in to the Su-30 building after drilling the 300mm thick wall and laying of 50 pair cable on the wall inside Su- 30 building with the help of clamp and saddle fixed 800mm apart. 48 Drilling of 300mm wall for entering 50 pair cable in to Su-30 telephone distribution room in Su-30 building. Total amount in words: 2 No. 1 No. 2 Mtrs. 2 No. 3 Mtrs. 2 No. 10 Mtrs. 146 Mtrs. 55 Mtrs. 1 No. Page 5 of 6

6 TECHNICAL REQUIREMENT & GENERAL NOTES: 1. The work has to be done in accordance with laid down specifications in tender documents & MES SSR 2010 specification, Indian standards and Engineering notice in terms of the contract provisions and as per the direction of Engineering in-charge. General conditions of HAL contracts & procedure shall be applicable to this work. 2. Telephone cables to be supplied should be ISI grade 3. There will be a warranty of 12 months from the date of completion and handlng over to HAL for any work manship/ materials defeats. 4. The route of telephone cable should not interfere with HT/LT electric cable and a minimum distance of 3 ft between the two should be maintained. 5. For cable lying, earth should be digged 80cm to 100cm deep & after cable laying the trench should be filled with sand & bricks for cable protection. 6. The under ground cable laying route should be marked suitably at some points. 7. Drawing/Wiring diagram of each MDF or DB having more than 50 pair connections to be provided by contractor. 8. After cable laying, continuity & isolation tests of each wires with MDF/DB will have to be done. 9. The work should be completed within 4 months from the starting date mentioned in work order. 10. An agreement on a non judicial stamp paper of value Rs. 100/- will have to be executed within 15 days of receiving work contract % income tax/or as applicable shall be deducted as per rules % sales tax/ 14.00% Service tax or as applicable on works contract shall be deducted from the bills as per rules. 13. All materials whether to be consumed in the work or to be taken back later shall be entered through proper challans duly checked and entered by HAL security gate. 14. All materials are to be inspected by Engineer-in-charge for the work to ensure acceptance. One copy of challans duly enclosed by Engineer-in-charge & with security gate certificate shall be attached to the bills for payment % payment will be made against material brought on site and balance 25% against final bill after successful completion of work to the satisfaction of Engineer-in-charge. For Hindustan Aeronautics Limited Avionics Division, Korwa ( Ranjan Dutta) CM (Plant Maint) Page 6 of 6