Linkeo 19" freestanding cabinets

Transcription

1 87045 LIMOGES Cedex France Telephone: (+33) Fax: (+33) Linkeo 19" freestanding cabinets Page 1. General characteristics Range Technical characteristics Dimensions Baying Plinths Cable management Fan kits Castors " equipment GENERL CHRCTERISTICS Linkeo 19" freestanding cabinets are intended for digital infrastructures. Linkeo 19" cabinets are metal and provide IP20 - IK08 protection. They have a door with a glass window and are grey RL Linkeo 19" cabinets can be joined together and can be equipped with a plinth. Equipment and accessories for thermal and cable management such as fan kits, cable trays and shelves, etc. complete the range. 1.1 Presentation The main parts of Linkeo 19" freestanding cabinets are: - framework consisting of 4 uprights and 2 end plates - front door with a glass window - 2 side panels (excluding extension cabinets) - rear panel - Two 19" uprights (two additional uprights possible) 1. GENERL CHRCTERISTICS (continued) 1.1 Presentation (continued) The 4 structural uprights and the 2 end plates form a metal framework that is screwed together. The cabinet can be dismantled completely if access is difficult. The top and bottom end plates include a cable entry and an area for the fan kit. Pre-cut, they can be knocked out with a mallet. The whole structure stands on 4 levelling feet. The front door has a colourless transparent glass window and is fitted with a locking bolt. The door is removable and reversible. The side and rear metal panels are equipped with: - locking bolt - stainless steel equipotential link clip Each panel is removable. The clip automatically provides continuity of the metal conductive parts between the panels and the rest of the cabinet. Technical data sheet: F01695EN/00 Updated: Created: 23/01/2013 1/12

2 1. GENERL CHRCTERISTICS (continued) 1.1 Presentation (continued) The depth of the 19" uprights can be adjusted in 25 mm steps: 1. GENERL CHRCTERISTICS (continued) 1.2 Standards (continued) Linkeo 19" freestanding cabinets can be integrated in installations complying with the following standards: EN EN & 2 C & 2 ISO IEC NF C Part 4-41 IEC Information technology - Generic cabling systems Information technology - Cabling installation Information technology - Generic cabling for customer premises Low voltage electrical installations - recommendations Low voltage electrical installations - Protection for safety - Protection against electric shock 25 mm 2. RNGE Linkeo 19" freestanding cabinets can be fitted with a set of 2 additional uprights at the back: The 19" uprights are perforated with 9.5 x 9.5 mm square holes. 1.2 Standards Linkeo 19" freestanding cabinets comply with the following standards: IEC EN Set of two 19" uprights For 24U cabinet For 33U cabinet For 42U cabinet (NF C ) Degrees of protection provided by enclosures (IP code) Capacity Width (1) (mm) Depth (1) (mm) U U U U U U U U U U Two extension freestanding cabinets complete the range. These are supplied without side panels and with a baying kit: Linkeo 19" extension cabinets Capacity Width (1) (mm) Depth (1) (mm) U U IEC EN IEC EN C EI-310-E IEC DIN (NF EN 50102, NF C ) Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code) Safety of information technology equipment Cabinets, racks, panels and associated equipment (NSI/EI/310-E-2005) (NF C , NF C ) Dimensions of mechanical structures of the mm series (19 in) (1) Designated dimensions. See section 4.1 for overall dimensions. 2/12

3 3. TECHNICL CHRCTERISTICS 3.1 Index of protection - IP20 according to IEC EN Protected against solid objects larger than 12.5 mm in diameter - IK08 according to IEC EN Protected against mechanical impact with an energy of 5 joules 3.2 Mechanical performance - Permissible load: 400 kg 3.3 Design - Structural uprights and upper end plate made of 1.5 mm thick galvanised steel + paint - Lower end plate made of 1.5 mm thick Z140 MB-C galvanised steel - Front door made of 1.2 mm thick steel + paint: vertical uprights grey RL 7035, top and bottom strips charcoal grey RL 7016 Window made of 4 mm thick colourless transparent safety glass. - Door hinges made of galvanised steel - Legrand marked in RL 7016 on door - Panels made of 1.2 mm thick sheet steel + paint - Door and panel bolts made of chrome-plated metal - 19" uprights made of 2 mm thick galvanised steel - Levelling feet made of zinc-plated steel with black polypropylene fixed base 3.4 Corrosion resistance - Corrosive environment class: C2 according to EN ISO , 3K3 according to IEC EN Salt spray test according to ISO 9227 (NSS test) and IEC EN (Ka test) for 168 hours: degree of rusting Ri1 according to ISO , propagation 1 mm according to ISO Sulphur dioxide (SO 2 ) test according to EN ISO 6988 for 48 hours: degree of rusting Ri1 according to ISO , ISO annex class 8 type image 3. TECHNICL CHRCTERISTICS (continued) 3.6 Electrical continuity of the conductive parts Continuity of the cabinet metal conductive parts is achieved by design. For the panels, a stainless steel clip automatically provides the equipotential link by pressing against the lower end plate with galvanised steel finish. For the door, the equipotential link should be created with the protective conductor supplied. 3.7 Weight Net weight excluding packaging. Cabinet Weight (kg) (extension ) 89 (71) (extension ) 115 (88) Note: Linkeo 19" cabinets are delivered on a 125 mm high pallet. 3.5 Properties of the paint coating - Thermosetting polyester paint applied by electrostatic dusting - Grey RL 7035 ( horizontal door strips: charcoal grey RL 7016) - Textured satin appearance - 60 to 80 mm µm thick - Excellent impact and scratch resistance - Excellent resistance to cleaning agents (excluding strong chlorinated, fluorinated and ketone solvents) Some products may change the appearance. It is therefore advisable to carry out a test first - Light exposure test (xenon-arc lamp) according to ISO method B for 500 hours: no visible fading 3/12

4 4. DIMENSIONS ll dimensions are in mm. 4.2 Glass window in front door 4.1 Dimensions Model shown: 600 x 600 mm cabinet Overall D W D W FRONT VIEW SIDE VIEW RER VIEW B H1 H2 135 Capacity W D Overall dimensions H1 H2 min./max. W D B U / U / U / U / U / U / U / U / U / U / Extension cabinets VIEW FROM BOVE (1) (1) (2) Note: The door opening angle is 105 when cabinets are joined (see section 5) U / U / (3) Glass window dimensions x x x x / x x x x / x x 450 (1) Designated dimensions (2) Without level adjustment feet (3) With level adjustment feet (+15 to 45 mm) 4/12

5 4.3 Usable dimensions mm wide freestanding cabinets 600 mm wide cabinets are available in 3 heights: 24U, 33U and 42U Usable dimensions (continued) mm wide freestanding cabinets (continued) 600 mm wide cabinets are available in 3 depths: 600, 800 and 1,000 mm. Model shown: 600 x 600 mm cabinet 630/830/1030 Capacity 24U/33U/42U Usable space 1086/1486/ Usable space Capacity 24U/33U/42U Usable space 996/1396/1796 Can be adjusted in 25 mm steps (4 x 25 mm) 425 max./625 max./825 max. Set of 2 additional 19" uprights Cat. Nos /41/42 70 Usable space 490 Usable space 490/690/890 FRONT VIEW (without door) SIDE VIEW 5/12

6 4.3 Usable dimensions (continued) mm wide freestanding cabinets (continued) 4.3 Usable dimensions (continued) mm wide freestanding cabinets 800 mm wide cabinets are available in 3 heights: 24U, 33U and 42U (206 max.) 85 (185 max.) (2) (1) (2) 425 max./625 max. Set of 2 additional 19" uprights Cat. Nos /41/42 507/707/907 - CROSS-SECTION VIEW (3) (with door) (1) Dimension below door on 19" uprights (2) Can be adjusted in 25 mm steps (3) See front view on page Usable space 450 Usable space 450 Fixing centres 465 (19") Capacity 24U/33U/42U Usable space 1086/1486/ /257/ VIEW FROM BOVE Note: The dimensions of the upper and lower end plates are identical. 88 Usable space 690 FRONT VIEW (without door) 6/12

7 4.3 Usable dimensions (continued) mm wide freestanding cabinets (continued) 800 mm wide cabinets are available in 3 depths: 600, 800 and 1000 mm Model shown: 800 x 800 mm cabinet 4.3 Usable dimensions (continued) mm wide freestanding cabinets (continued) Model shown: 800 x 800 mm cabinet /830/ Can be adjusted in 25 mm steps (4 x 25 mm) 106 (206 max.) 85 (185 max.) (2) (1) (2) 425 max./625 max./825 max. Set of 2 additional 19" uprights Cat. Nos /41/42 507/707/907 Usable space 450 Capacity 24U/33U/42U Usable space 996/1396/1796 Cable management ring fixing points (1) 425 max./625 max./825 max. - CROSS-SECTION VIEW (3) (with door) (1) Dimension below door on 19" uprights (2) Can be adjusted in 25 mm steps (3) See front view on page Fixing centres 465 (19") Set of 2 additional 19" uprights Cat. Nos /41/42 57/257/ Usable space 490/690/ SIDE VIEW VIEW FROM BOVE (1) See sections 7.2 and Note: The dimensions of the upper and lower end plates are identical. 7/12

8 5. BYING 4.3 Usable dimensions (continued) " uprights 50 8,25 31,25 15,87 15,87 44,45 44,45 23, ,5 311 Ø 5, Linkeo 19" freestanding cabinets can be joined together using baying kit Note: The Linkeo range includes extension cabinets for the 42U x 600 x 600 and 42U x 800 x 800 sizes. These special cabinets are supplied with the baying kit and without side panels. The kit consists of: - 4 galvanised steel lugs - steel crosspiece + paint (same as cabinets) - Fixing screws The crosspiece can be separated manually to make it suitable for the various cabinet depths. 2 7,5 9,5 42U U U The crosspiece provides protection against dust and maintains the IP20 protection of the cabinets at the top. 4.4 Positioning of supports on the floor The freestanding cabinets are equipped with 4 levelling feet (1610 overall) / / /546/ max. Feet Ø38 VIEW FROM BELOW VIEW OF JOINED CBINETS FROM BOVE 8/12

9 6. PLINTHS Linkeo 19" freestanding cabinets can be equipped with a 100 mm high metal plinth. For cabinet width x depth (mm) x x 800/800 x x x x CBLE MNGEMENT 7.1 Vertical cable trays side and/or rear cable trays can be installed in Linkeo 19" freestanding cabinets. They are mounted directly on the structure: Linkeo plinths consist of 4 corner blocks and 4 removable traps. The plinths are the same colour as the cabinets (grey RL 7035). The plinth is fixed directly to the cabinet end plate: D W Vertical cable tray For 33U cabinet For 42U cabinet Note: It is possible to place 2 plinths one on top of the other. Characteristics - Plinth fixed using M12 screws - Traps fixed using white zinc-plated M6 screws - Corner blocks made of 2 mm thick steel + paint (same as cabinets) - Traps made of 2 mm thick steel + paint (same as cabinets) - Supplied with complete set of screws for the equipotential link with the cabinet - Can be fixed to the floor (screws not supplied) D L Width 14 C P B Depth B 100 Characteristics - 50 x 7 mm oblong perforations (possibility of clamping using cable ties) - Supplied with screws mm thick Z140 MB-C galvanised steel Overall dimensions (mm) x 300 x x 300 x 25 Mounted at the back, the tray is centrally positioned in the cabinet width. For side mounting, the table below gives the position of the tray axis in relation to the back of the cabinet: D 14 C 100 Cabinet depth W x D Dimensions (mm) Overall Fixing (1) Usable space Width Depth B C D 600 x x x x x x (1) Identical dimensions when fixed to the floor Depth 9/12

10 7. CBLE MNGEMENT (continued) 7.2 Cable management ring Linkeo 19" 800 mm wide freestanding cabinets can be fitted with metal cable management rings (set of 6). The rings are mounted on the outside of the 19" uprights: 8. FN KITS Linkeo 19" freestanding cabinets can take a fan kit. Installed at the top, it ensures a high extraction rate. No. of fans Output (m 3 /hr) Once you have knocked out the cut-out with a mallet, the kit is fixed directly to the cabinet end plate: Cabinet capacity 24U/33U 42U Positioning the fixing points, see section Characteristics - Set of 6 rings - Usable dimensions: 65 x 145 mm - Supplied with screws - Painted steel, 2.5 mm thick - Black RL Self-locking cable ties No. of ring fixing points 5 per 19" upright 7 per 19" upright Self-locking cable ties are repositionable textile ties that do not damage cables. Characteristics - IP XXB - IK V~ - 50/60 Hz power supply Current 325 () Power 325(W) Integrated thermostat, adjustable from 10 to +80 C - Equipped with 3 x 0.75 mm 2 flexible power supply cords, 2.5 m long with standard 2P+E French/German plug - Fixed using self-tapping screws with pins (supplied) - Plate made of steel + paint (same as cabinets) - Grey RL Colour Width (mm) Length (mm) Max. tightening Ø (mm) Black Red Green Black Red Green Tensile strength: >220 N - Fire resistance: UL 94 V2 - Double-sided textile with "loops" on one side and "hooks" on the other /12

11 9. CSTORS Linkeo 19" freestanding cabinets can be equipped with a set of 4 pivoting castors The total load on the 4 castors must not exceed 500 kg " EQUIPMENT 10.1 Management panels with 2 axes - Metal panels with horizontal and front to back feedthrough Characteristics - Set of 4 castors, 2 of which have brakes - Raise cabinet by 81 mm - Supplied with fixing screws - Black plastic wheel ,5 Ø 55 8,8 x 10,8 Ø 105 Ø 178 Height Depth (mm) Feedthrough dimensions (mm) Ring usable cross-section (mm 2 ) U x x U x x , ,5 - Panels made of 1 mm thick zinc-plated steel - Rings made of 2.5 mm thick zinc-plated steel - Supplied with screws and cage nuts with pins - Black RL Fixed shelves Projecting mounting fixed shelf - Fixed by screwing onto 2 x 19" uprights Depth (mm) Usable width (mm) Height 2U - Max. load: 15 kg - 50 x 7 mm oblong perforations (possibility of clamping using cable ties) - Supplied with screws and cage nuts with pins mm thick zinc-plated steel, black RL Fixed shelf for fixing on 4 x 19" uprights - Screw fixing - Can be adjusted in 25 mm steps to the depth of the 19" uprights For cabinet depth (mm) Depth (mm) Width (mm) Height 1U - Max. load: 50 kg - 50 x 7 mm oblong perforations (possibility of clamping using cable ties) - Supplied with screws and cage nuts with pins - Shelf made of 1.5 mm thick zinc-plated steel, black RL /12

12 10. 19" EQUIPMENT (continued) 10.3 Telescopic shelves - Fixed by screwing onto 4 x 19" uprights - Can be adjusted to the depth of the 19" uprights For cabinet depth (mm) Depth (mm) Width (mm) Travel (mm) Height 1U - Max. load: 30 kg - 50 x 7 mm oblong perforations (possibility of clamping using cable ties) - Supplied with screws and cage nuts with pins - Shelf made of 1.5 mm thick zinc-plated steel, black RL Ball-bearing runners If there is a risk of tilting when heavy items are removed, the cabinet must be fixed to the floor " PDUs - Designed to provide 230 V~ power supply for active products - For mounting on 19" fixing centres - 2P+E sockets - Equipped with a flexible 2 m power supply cord, 3 x 1.5 mm 2 with plug - Height 1U - Supplied with screws - Black aluminium body, black steel fixing lugs Number 2P+E sockets Standard dditional function French Belgian Switch with indicator German Switch with indicator British Switch with indicator 12/12