Modular Plug Connectors Compliant to Enhanced Category 5 Standards TM2P Series (Shielded Type) TM22P-88P (Non-shielded Type) Features. Supports High-Speed LAN Transmission Conforms to requirements of TIA/EIA-568B data wiring standard, meeting transmission performance of Enhanced Category 5. Supports Gigabit Ethernet (BASE-T) and Fast Ethernet (BASE-TX) high-speed LAN transmission. 2. EMI protection (TM2*P-88P) 36 coverage of the engagement area with a metal shield assures protection against electromagnetic interference. When mated with corresponding connector the shield surfaces are securely connected to provide continuous circuit. 3. Protected latch tab (TM2P-88P) Flexible case extends over the release tab preventing the possibility of breaking-off during handling of the complete cable assembly. 4. Termination of conductors Self located 24 AWG conductors (solid or stranded) are terminated against pre-inserted contacts using simple tooling. 5. Simplified termination (TM2*P-88P) Removeable one piece cover allows easy access to the termination areas. 6. Conforms to the ISO 8877 Standard (ISDN Interface Connector) Protected latch tab 2 Cover Installation Procedure 97
Product Specification Rating Current rating Voltage rating A 25 V AC Operating temperature range-25ç to +6ç (Note) Item Specification Conditions. Insulation resistance M ohms min. V DC 2. Withstanding voltage (between adjacent contacts) No flashover or insulation breakdown 5 V AC / one minute 3. Withstanding voltage (between contact and shield) No flashover or insulation breakdown 5 V AC / one minute 4. Contact resistance 23 m ohms max. ma DC 5. Vibration 7. Durability (mating/un-mating) Contact resistance: 25m ohms max. 2 Temperature: -55ç/+5ç to +35ç/+85ç/+5ç to +35ç 8. Temperature cycle Contact resistance: 25 m ohms max. Duration: 3/5/3/5(Minutes) Insulation resistance: M ohms min. 5 cycles 9. Humidity Contact resistance: 25 m ohms max. Insulation resistance: M ohms min. (High humidity) 5 hours at temperature of 4ç and humidity of 9% to 95% Insulation resistance: M ohms min. (Dry state). Salt Spray Contact resistance: 25 m ohms max. Exposed to density 5% salt water for 48 hours Note :Includes temperature rise caused by current flow. Materials No electrical discontinuity of 5 ms or more Contact resistance: 25m ohms max. 6. Shock No electrical discontinuity of 5 ms. min. Contact resistance: 25m ohms max. Frequency: to 55 Hz, single amplitude of.75 mm, 2 hours / 3 axis Acceleration of 49 m/s 2, ms duration, sine half-wave waveform, 3 cycles in each of the 3 axis Part Material Finish Remarks Insulator Polycarbonate Color: Clear UL94V-2 Contacts Copper alloy Contact area: Gold plating ------- Shield Copper alloy Tin plating ------- Conductor holding tray Polycarbonate Color: Clear UL94V-2 Cover Polyamide Color: Light beige (Note) UL94V-2 Note :Cover available in various colors. Refer to page 3. Ordering information Plugs- Shielded TM2 C P - 8 8P 2 3 4 Plugs - Non-shielded TM22P - 8 8P 2 3 Series name TM2P: Shielded 2 Cover Type Blank: Protective latch cover C: Short cover 3 Size 8: For 8 contacts 4 Inserted contacts 8P: 8 Series name TM22P : Non-shielded 2 Size 8 : For 8 contacts 3 Inserted contacts 8P: 8 98
Plug Connectors Shielded Part Number TM2P-88P TM2P-88P(2) TM2P-88P(3) TM2P-88P(4) 3.2 7.5 6.9.7 6.6 (.6) 2.9 Contact No. CL No. 222-2862-9-2 222-2862-9-2 222-2862-9-3 222-2862-9-4 (R3.5) 6.7 (34) 6.6 9 Conductor holding tray Contact No.8 5.4 Cover Color Light beige Medium gray Black Natural light gray 29.5 3.45 9.5 Cover TM2P-88P(5) 222-2862-9-5 Red TM2P-88P(6) 222-2862-9-6 Green TM2P-88P(7) 222-2862-9-7 Blue TM2P-88P(8) 222-2862-9-8 Yellow TM2P-88P(9) 222-2862-9-9 Orange Cover installed Mated with corresponding receptacle (shown for reference only) (34) (3.4) (44.65) 99
Plug Connectors Shielded-Short Cover 6.7 7.2 Cover 3.2 6.9.7 (22.4).4 9 TM2CP-8 TM2CP-8 7.5 (R3.5) Part Number CL No. TM2CP-88P(3) 222-2884--3 Note: For other colors contact Hirose sales representative. Cover installed (3.4 ) (32.35) Applicable Shielded Cable Specifications TM2CP-8 Cover color Black Specifications 6.6 2.9 (.6) Contact No. Conductor holding tray Contact No.8 9.5 Mated with corresponding receptacle (shown for reference only) (2.7) TM2CP-8 5.4 3.45 Solid copper conductor:.5mm dia. Jacket Shield Insulation Conductor Stranded copper conductor: AWG#24 (Dia..2mm x 7 pcs) Conductor Individual conductor insulation dia. (.9mm to.mm) Drain wire AWG#26 (tin coated) Drain wire Overall jacket dia. (dia. 6.6mm) Note: For cable termination procedures refer to: [TM2P-88P Cable Termination Procedure Manual] (ETA-E2349) and [TM2CP-88P Cable termination Procedure Manual] (ETA-E2353). Some cables may not meet the required service ratings. Contact Hirose sales representative for specific cable applications recommendations. 2
Plug Connectors Non-shielded 22.5 6.9.7 Conductor holding tray 3.45 5.4 9.5 4.2 7.9 (.6) 6.6 Contact No. Contact No.8 Part Number CL No. TM22P-88P 222-2899-9 Mated with corresponding receptacle (shown for reference only) (.85) Applicable Non-shielded Cable Specifications Specifications Jacket Conductor Solid copper conductor:.5mm dia. Stranded copper conductor: AWG#24 (Dia..2mm x 7 pcs) Conductor Insulation Individual conductor insulation dia. Overall jacket dia. (.9mm to.mm) (dia. 5.4mm to 5.7mm) Note: For cable termination procedures refer to: [TM22P-88P Cable Termination Procedure Manual] (ETA-E238). Some cables may not meet the required service ratings. Contact Hirose sales representative for specific cable applications recommendations. 2
Hand termination tools For contact/conductor termination (For cable and shield crimping) For contact/conductor termination (Non-shielded connectors) Part Number CL No. Applicable connector HT6-TM23/22P-88P CL92-228- TM22P-88P TM23P-88P Part Number CL No. Applicable connector HT6 / TM2P-88P 92-233- HRS marking side (For contact/conductor termination) A Reverse side (For cable strain relief clamp crimping) TM2P-88P TM2CP-88P 22
Technical Documentation CAT5e Transmission Characteristics Data These are the representative values of the various transmission characteristics data for connector assemblies TM2P-88P and TM2R-5C-88-LP when fully mated. Signal Attenuation.5 Attenuation(dB) NEXT(dB).4.3.2. 2 3 4 5 6 7 8 9,2 3,6 4,5 7,8 CAT5e Spec (Each two numbers are for the pair of individual contact position.) Near-End Crosstalk Attenuation (NEXT) Return Loss 2 8 6 4 2 2 3 4 5 6 7 8 9,2-3,6,2-4,5,2-7,8 3,6-4,5 3,6-7,8 4,5-7,8 CAT5e Spec 8 Return Loss(dB) 6 4 2 2 3 4 5 6 7 8 9,2 3,6 4,5 7,8 CAT5e Spec 23
Powered by TCPDF (www.tcpdf.org) The product information Far-End Crosstalk Attenuation (FEXT) 2 FEXT(dB) 8 6 4 2 Propagation Delay Delay(ns) Delay Skew(ns) 3 2.5 2.5.5 Propagation Delay skew.4.2.8.6.4.2 2 3 4 5 6 7 8 9,2-3,6 3,6-4,5 4,5-7,8 CAT-5e Spec,2-4,5 3,6-7,8 7,8-,2,2-7,8 4,5-,2 7,8-3,6 3,6-,2 4,5-3,6 7,8-4,5 2 3 4 5 6 7 8 9,2 3,6 4,5 7,8 CAT5e Spec 2 3 4 5 6 7 8 9 (Each two numbers are for pair of individual contact position.) Measurement Value CAT5e Spec 24