HUBER+SUHNER DATA SHEET Sencity Rail Antenna: 1399.17.0044 Rev.: AC SWA-0859/360/4/0/DFRX30 Description Railway rooftop antenna: GSM 900, GSM 1800, GSM 1900, UMTS, 2.4, 3.5, 5.3 and 5.8 GHz Bands and /Galileo incl. LNA. Rugged design, meets EN 50155 railway standard. Embedded /LNA. Works also on non-metallic surfaces. Product Configuration Technical Data Electrical Data Band 1 Band 2 Band 3 Band 4 Frequency (MHz) 870-960 1710-2170 2400-2700 3400-3700 VSWR 1.5 1.5 1.5 1.5 Gain (dbi) 6 8.5 9.5 9.5 3dB beamwidth (h) ( ) 360 360 360 360 Isolation between Ports (db) 30 40 40 37 Band 5 Frequency (MHz) 5150-5875 VSWR 2 Gain 8.5 dbi 3dB beamwidth (h) ( ) 360 Isolation between Port 28 db General Data Nominal Impedance 50 Ω Polarisation vertical Connector N, jack (female), bottom Composite Power max. 100 W Ambient Temperature 50 C Note that all VSWR values are guaranteed with and without ground plane. Electrical Data () Frequency (MHz) 1574.397-1576.443 VSWR 1.6 Nominal Impedance 50 Ω Polarisation circular right Connector N, jack (female) Remarks Antenna gain: 6dBi LNA Operating Voltage 5 V LNA Noise Figure 2.7 db LNA Current Consumption 25 ma LNA Gain 27 db Out of Band Rejection 1 40 LNA out of band attenuation: >20dB at fo + - 50MHz, >40dB at fo + - 100MHz LNA Operating voltage range: 3.0 to 5.5VDC Mechanical Data Dimensions (mm) Weight 90 x 100 x 260 (Height x Width x Depth) 1.2 kg HUBER+SUHNER is certified according to ISO 9001 and ISO 14001 HUBER+SUHNER Excellence in Connectivity Solutions
HUBER+SUHNER DATA SHEET Sencity Rail Antenna: 1399.17.0044 Rev.: AC Windload frontal: 0.7 N, lateral: 10 N at km/h Wind Speed survival: 250km/h, operational: 500 km/h Designed acc. to UIC 533, DC-grounded antenna element (protection against lightning and short circuit with catenary lines (40 ka/0.1s). Low corrosion design acc. to MIL-F-14072(D). Environmental Data Operation Temperature ( C) -40 to 85 IP Rating IP 68 Storage Temperature ( C) -40 to 85 Transport Temperature ( C) -40 to 85 Solar Radiation DIN 75220 RoHS not compliant Tested acc. to EN 50155:2001 (Environmental tests). Material Data Radome Colour Back Plate/Base Plate Colour Back Plate/Base Plate Material Related Products RAL 7043 (dark grey) RAL 7043 (dark grey) Aluminium 9091.99.0189 Adapter plate for antenna 1399.17.0043/.0044 Related Documents Mounting Instruction Painting Instruction Security Instruction Outline Drawing1 Additional Information DOC-0000197864 DOC-0000256180 DOC-0000278984 DOU-00061635.1 This product meets the Deutsche Bahn specifications for rolling stock equipment. HUBER+SUHNER is certified according to ISO 9001 and ISO 14001 HUBER+SUHNER Excellence in Connectivity Solutions
HUBER+SUHNER SENCITY RAIL ANTENNA FOR WIRELESS COMMUNICATION Mounting Instruction Keep away from catenary and high voltage lines. Be careful when working at height! Always secure ladders! Always tighten screws! If exposed to extreme environmental conditions, especially polluted atmosphere, the connectors should be covered with a self-vulcanising tape or a cold shrink tube. Dimensions in millimetre [mm] 1) The diameter of the hole should allow for the tightening of the N plug connector to the antenna. The standard N plug connector has a diameter of Ø 21. 2) The roof of the vehicle should have sufficient mechanical stability to ensure a correct sealing of the antenna. 3) The electrochemical potentials between the antenna (aluminium) and the roof should be minimized. The roof of vehicle has to be clear of paint and other contaminants (protection against short-circuit with overhead lines). 4) The blue ring marks. Do not remove it. Plate mounting not included see 4) Ø 17 1)... Ø 38 Page 1 of 2
Mounted with adapter panel - standard hole pattern Adapter Panel 9091.99.0189 Screws M8 selflocking and selfsealing (DIN 267 part 28) included. see 4) cut - out for M10 screws Ø 25 1)... Ø 38 Mounted w ith adapter panel - standard hole pattern w ith M10 threated fastener Adapter Panel 9091.99.0189 Screws M8 selflocking and selfsealing (DIN 267 part 28) included. see 4) cut - out for M10 screws M10 threated fastener height max. 18 Ø 25 1)... Ø 38