CABLE ACCESSORIES 110-220 kv
Termination 110 kv Technical description Termination MKB 126 / 145 with composite type insulator uses for cable line joints with other elements of power-supply systems. Termination MKV 126 /145 is used for outdoor and inner installation, for XLPE cables 64/110 kv with the conductor cross-section 2000 2. Basic components Insulator composite type insulator with glass fiber reinforced epoxy resin tube and silicon rubber alter-nating sheds color light gray top and bottom flanges glued and sealed to the composite insulator Description Maximum operated voltage, Um Maximum cable insulated diameter Maximum cable sheath diameter Cable conductor cross section range Maximum allowed inclination,angle Termination length, L Creepage distance length Pollution level in accordance with IEC 60137; All Union State standard 9920-89; Electrical installation codefkb Volume of pack compaund Weight Maximum allowed force on top connector kv 2 l kg kn MKV 126 / 145 126 94 115 185-2000 30 1540 1863 1875 3670 4300 5000 III IV IV+ 28 32 38 104 108 113 3,5 3,5 3,5 Cable end pre-moulded and factory-tested silicon stress cone cable end base plate branch pipe with flange support insulators seals and fixing materials unpressurised synthetic oil as an insulating medium optic fiber outlet for the connection to the equipment Area of application Type MKV 126 / 145 Maximum system voltage, kv 126 / 145 Cable conductor cross section range, 2 185 2000 Maximum cable sheath diameter, 115 Maximum cable insulation diameter, 94 Demands to the electrical parameters: AC voltage withstand test: Partial discharge test: Impulse voltage (10+/10- impulses) Environmental characteristics: Climatic category: Nominal operating current: limited by cable specification 160 kv for 30 min / 190 kv for 30 min 5 pc at 96 kv / 5 pc at 114 kv 550 kv / 650 kv YUHL1 Stress cone routine tests for MKB 126 / MKB 145 Test voltage level: 160 kv for 30 min / 190 kv for 30 min Partial discharges level: <5pC at 96 kv / <5pC at 114 kv Support insulator withstand voltages: AC voltage: 10 kv DC voltage: 20 kv Mechanical characteristics: Maximum allowed inclination with vertical: 30 C Approximate weight, kg: 115 Maximum allowed force on top connector, H (horizontal): 3500
Additiory Cable clamps To fix the cable before the termination and joints, we need the BKK cable clamps with the rubber inserts (PST-80), which exclude the cable longitudinal movement. Type BBK L l h d 65/90 175 140 50 13 85/105 185 150 64 13 100/125 204 170 67 13 Joints 110 kv Technical description The pre-moulded outdoor joint MSV 126 / 145 is designed to connect two extruded high voltage cables XLPE 64/110 kv. Joint MSV 126 / 145 could be produced in different ways which admitted the possibility of screen wires direct connection, cross-bonding connection of different cable phase wires screen (screen transposition), wires screen connection with optical fibers in the metal tubes. Basic components Insulator Silicon pre-moulded joint body with elements for electrical field control Connector and sealing materials One piece pre-moulded silicone insulator Special tapes for different purposes Protective covering from shrinkable tubes and sleeves (optionally it is possible to order other protective covering) Contact clamps To connect terminations to the networks, we need to apply contact clamps. Arkasil SK supplies aluminum, bronze and bimetallic contact clamps. Area of application Type MSV 126 / 145 Maximum system voltage, kv 126 / 145 Cable conductor cross section range, ² 185 2000 Maximum cable sheath diameter, 115 Maximum cable insulation diameter, 91 Technical data Splice box It is applied for connection of fiber-optical modules installed in the high-voltage cables screens. Splice box is a protective metal tray, safety class IP66, with 4 inputs for fiber-optical modules, 2,5-5,5 in diameter. It protects the connection point and is applied to store the fiber stock necessary for repair or preventive works. Demands to the electrical parameters: AC voltage withstand test: 160 kv for 30 min. / 190 kv for 30 min. Partial discharge test: <5 pc at 96 kv / <5 pc at 114 kv Impulse voltage (10+/10- impulses) 650 kv Environmental characteristics: Climatic category Currency load rating: Rated operational current: Short circuit current: limited by cable specification limited by cable specification YUHL1
Stress cone routine tests: Test voltage level: Partial discharges level: Support insulator withstand voltages AC voltage: DC voltage: 160 kv for 30 min / 190 kv for 30 min <5pC at 96 kv / <5 pc at 114 kv 10 kv within 1 min 20 kv within 1 min Mechanical characteristics: Approximate weight, kg: 35 Joints overall dimensions MSV 126 / 145 Installation and Supervision service Arkasil SK renders services on installation and supervision of own high-voltage cable accessories. Our installation supervision services for the cable ac-cessories shall mean: Multipurpose and process supervision. The works quality control of the personnel trained in Arkasil SK to installed cable accessories and who have special certificates. Guarantee documentation on the installed Arkasil SK cable accessories. The Arkasil SK cable accessories related consultations. " Installation Supervision" in the construction standards is not defined yet. Therefore, when making an agreement, it is necessary to be governed by the normative documents, including The Regulations For Installation/ Supervision, governing the bases for granting consulting services and the contractual relations, in general. Our service on cable accessories installation shall include: Joints overall dimensions MSV 126 X / 145 X - Installation of the Arkasil SK cable accessories by the specialists certified by Arkasil SK for these works. - Guarantee documentation on the installed Arkasil SK cable accessories. - The Arkasil SK cable accessories related consultations. For more information on the installation and supervision provided by Arkasil SK, please call: +7 (495) 669-39-49 Additionary Joint Splice box It is applied for connection of fiber-optical modules installed in the high-voltage cables screens. A joint splice box is a protective rubber base with slots and channels for the optical fibers, it provides connection of the modules, protects the connection point. It is fixed during the joint installation. The supply complete set includes all necessary accessories for the optical modules welding. Installation Training Arkasil SK arranges training for the installation contractor specialists. The training is arranged at the training center located at the Arkasil SK production facilities. There, for optimization of the educational process, Arkasil SK renders the training service at the installation contractor production facilities. The training shall include: Theory training Practical training Tests Sample preparation for certification Granting certificates By the results of examinations, the installation contractor specialists shall receive the permits for performance of installation works with the Arkasil SK cable accessories.
Tools for Arkasil SK cable accessories installation Installation Tool Kits 1010 Kit ( The installation tools including all necessary items for the highvoltage ca-ble and cable accessories preparation and installation) Unicut 30 Universal Cable Machine (For removal of the semi-conducting screen and insulation from the high-voltage cables, the 30-85 diameter over insulation) Unicut 40 Universal Cable Machine (For removal of the semi-conducting screen and insulation from the high-voltage cables, the 70-125 diameter over insulation) 1000 kg Belt Winch. (For pulling the silicon insulator on the cable) Cable Heating Kit 1080 Kit (For the high-voltage cable heating. In addition, the kit shall include the temperature setting and controlling instruments) Winch-to-Cable Fixing Device (The device is fixed on the cable, and has terminals for fixing the winches) Other Auxiliary and Installation Tools Arkasil SK Contacts: 111033, Russia, Moscow, Zolotorozhskiy Val 32, bld.10 Тel./Fax: +7 495 669-39-49 E-mail: info@arkasil.com web-site: www.arkasil.com