SECTION OPTICAL FIBER CABLES AND ACCESSORIES. A. Interior Raceways, Fittings, and Accessories: Section

Transcription

1 SECTION OPTICAL FIBER CABLES AND ACCESSORIES PART 1 GENERAL 1.01 RELATED WORK SPECIFIED ELSEWHERE A. Interior Raceways, Fittings, and Accessories: Section B. Wiring, General Volts And Under: Section REFERENCES A. EIA/TIA 568B. B. EIA/TIA SYSTEM DESCRIPTION A. For elevators as shown on the drawings, provide bi-directional contactor closure transceivers, with associated wiring, termination points to achieve two (2) separate signals for the elevator controllers: 1. "20 Second Pre Transfer Notification prior to Retransfer to Utility Power". 2. "Bus powered from Generators". B. The 20 Second Pre Transfer Notification signal will allow the elevators to stop at the primary floor prior to retransfer and resume normal operation once re-transfer is made via contactors (open/close). 1. Pre-transfer notification signal: a. Contacts will close 20 seconds prior to return to utility from generator power. b. Contacts will open when transfer has been made back to utility. C. When the Bus receives power from the Generators and the main generator breaker closes and a signal will be sent to control a lobby emergency light via contactors (open/close). 1. Bus powered from Generators signal: a. Contacts will close when Generator power is supplied. b. Contacts will open when Normal power is restored. D. The signals will originate from the generator main transfer switch located in the Power House via existing dry contacts on generator circuit breaker and existing 20 second time delay relay UELEV. Relay UELEV is coordinated with existing relay UNR which has an existing time delay of 8 minutes and 32 sec prior to retransfer back to utility. The time delay relay for re-transfer back to normal power shall be coordinated to allow for proper communication period across the Willard network Project No E

2 E. The state of the contacts and relays will be monitored and transmitted by a bi-directional contact closure from the Seneca Home building to the various elevator locations utilizing the existing fiber network. The bi-directional contact closures will be located in each buildings data closet and the Seneca Home main data room. F. Provide two (2) sets of dry contacts for the Elevator Contractor to receive notice of: 1. Emergency generator power is supplied. 2. Re-transfer notification. G. Provide two (2) #16 AWG wire and conduit from the data closet to the elevator machine room located within the required buildings and connected to a bi-directional contact closure transceiver for the emergency generator signals. H. Elevator Contractor will provide: 1. Final connections to elevator equipment for pre-notification signal and emergency light. 2. Emergency lights and associated elevator control programming. I. Provide two (2) GXT-700RT UPS's and rack mounted plug strips for bi-directional contact closure transceivers in Seneca Home main data room. Locate in existing main fiber termination rack SUBMITTALS A. Waiver of Submittals: The "Waiver of Certain Submittal Requirements" in Section does not apply to this Section. B. Submittals Package: Submit the shop drawings, point-to-point wiring diagrams, training submittals, and product data submittals specified below at the same time as a package within 60 days of contract award. C. Shop Drawings: 1. Submit scale drawings of the proposed rack layout. D. Product Data: 1. Catalog sheets, specifications, and installation instructions for all products. 2. Complete manufacturer's construction details and specifications for the cables, including (for fiber optic cable): a. Physical and optical characteristics of the optical fibers. 1) Cable manufacturer's certified test data (attenuation, bandwidth). b. Physical characteristics of strength members and jackets. c. Overall dimension of cable. E. Samples (if requested when submitting other than what is specified): 1. One 4 foot sample of each type cable proposed for use. F. Contract Closeout Submittals: 1. System acceptance test report. 2. Operation and Maintenance Data: Project No E

3 a. Deliver three complete paper sets and one CD copy of CAD drawings (AUTOCAD Version 12 or higher), covering the installed products, to the Director's Representative. Include: 1) Complete point-to-point wiring diagrams of the modifications as installed. Identify all conductors and show all terminations and splices. (Identification shall correspond to markers installed on each conductor). 2) The drawings must show the provided cable ID numbers of all data closets where cable was installed DELIVERY, STORAGE AND HANDLING A. Cable Delivery: 1. No cable over one year old when delivered to the site will be accepted. B. Cable Storage: Store where cable will be at temperature recommended by cable manufacturer for optimum workability. PART 2 PRODUCTS 2.01 CONNECTORIZED OPTICAL FIBER JUMPER CABLES A. Type JFO: Jumper cable by Radiant Communications Corp., having: 1. One 62.5 micron/125 micron (core/clad) multimode optical fiber. 2. Kevlar or Aramid yarn strength member. 3. PVC outer jacket. 4. Cable length of 1 meter. 5. Connectors: Factory installed, stainless steel bodies and ferrules. a. One SC type connector, for connection to optical fiber termination rack (OFTR). b. The other connector s type shall be as required, for connection to the optical fiber receiver or transmitter equipment. 6. Field verify core/clad type. B. Type JFO: Jumper cable by Radiant Communications Corp., having: 1. One 8.3 micron/125 micron (core/clad) single mode optical fiber. 2. Kevlar or Aramid yarn strength member. 3. PVC outer jacket. 4. Cable length of 1 meter. 5. Connectors: Factory installed, stainless steel bodies and ferrules. a. One ST type connector, for connection to optical fiber termination rack (OFTR). b. The other connector s type shall be as required, for connection to the optical fiber receiver or transmitter equipment. 6. Field verify core/clad type Project No E

4 2.02 RACK MOUNT UPS A. AC Input: 120 VAC, 5.8 amps. B. Output Power Capacity: 780 watts/700 VA. C. Maximum Configurable Power: 1980 watts/2200 VA. D. Nominal Output Voltage: 120V. E. Efficiency at Full Load: 95%. F. Output Voltage Distortion: Less than 5% at full load. G. Output Frequency (Sync to Mains): 47 to 53 Hz for 50 Hz nominal, 57 to 63 Hz for 60 Hz nominal. H. Crest Factor: Up to 5:1. I. Waveform Output Type: AC Sine wave. J. Output Connections: Six NEMA 5-15R. K. Design Make: Liebert GXT-700RT with rack mount kit BI-DIRECTIONAL CONTACT CLOSURE TRANSCEIVER A. Bi-directional contact closure transceiver (multimode optical fiber) - Comnet Communications Network, FDC10M1: 1. Bi-directional transmission in one or two directions over one multimode optical fiber. 2. Distance 10 miles VDC,.5 amp relay output, normally open. 4. Voltage transient protection. 5. Dry contacts.5 MSEC response, normally open. 6. Wavelentgh / Power - 9 volt DC plug in power supply. B. Bi-directional contact closure transceiver (single mode optical fiber) - Comnet Communications Network, FDC10S1: 1. Bi-directional transmission in one or two directions over one single mode optical fiber. 2. Distance 43 miles VDC,.5 amp relay output, normally open. 4. Voltage transient protection. 5. Dry contacts.5 MSEC response, normally open. 6. Wavelentgh / Power - 9 volt DC plug in power supply Project No E

5 2.04 ACCESSORIES A. Pulling Compounds: As recommended by cable manufacturer. B. Tags: Precision engrave letters and numbers with uniform margins, character size minimum 3/16 inches high. 1. Phenolic: Two color laminated engraver's stock, 1/16 inch minimum thickness, machine engraved to expose white inner core color. 2. Aluminum: Standard aluminum alloy plate stock, minimum.032 inches thick, engraved areas enamel filled or background enameled with natural aluminum engraved characters. C. Markers: 1. Premarked self-adhesive: W.H. Brady Co.'s B940, Thomas and Betts Co.'s E-Z code WSL self-laminating, Ideal Industries' Mylar/Cloth wire markers, or Markwick Corp.'s permanent wire markers. 2. Flexible sleeve markers: Plastic Extruded Parts Inc.'s FS series. 3. Snap-on markers: Plastic Extruded Parts Inc.'s RS series. D. Power Strip (8 outlets): Chatsworth E. Two (2) 19 in. Black Shelf: Chatworth's PART 3 EXECUTION 3.01 VERIFICATION OF CONDITIONS A. Verification of Existing System: 1. Prior to modifying the system, verification portions of the existing system to ascertain their operating condition. a. Existing optical fiber and terminations. 2. Prepare a written report for the Director s Representative indicating the repairs required, if any, to make the existing system function properly. 3. Repairs to the existing system are not included in the Work unless requested by Order on Contract INTERRUPTIONS TO EXISTING SYSTEM A. Maintain the existing system in its present condition to the extent possible while installing new Work. B. Prior to making changes relative to the existing system, notify the Director s Representative and have procedures approved INSTALLATION A. Install the Work in accordance with the Company s printed instructions unless otherwise indicated Project No E

6 B. Identification, Labeling, Marking: 1. Identification of Circuits: Identify wires, cables, and tubing by system and function in interconnection cabinets to which they connect with premarked, selfadhesive, wraparound type markers. Designations shall correspond with point to point wiring diagrams FIELD QUALITY CONTROL A. Preliminary System Test: 1. Preparation: Have the Company Field Advisor adjust the completed system and then operate it long enough to assure that it is performing properly. 2. Run a preliminary test for the purpose of: a. Determining whether the system is in a suitable condition to conduct an acceptance test. b. Checking and adjusting equipment. c. Training facility personnel two (2) 2-hour training sessions. B. System Acceptance Test: 1. Preparation: Notify the Director s Representative at least 3 working days prior to the test so arrangements can be made to have a Facility Representative witness the test. 2. Make the following tests: a. Test system operational functions associated with the modifications. b. Test each monitor and control device connected or added under this project. 3. Supply all equipment necessary for system adjustment and testing. 4. Submit written report of test results signed by Company Field Advisor. END OF SECTION Project No E