AVENTOS HF Narrow aluminum door application Lift mechanism set Lift mechanism (qty ) #7 x 35 mm (-3/8 ) wood screw (qty 0) Power factor 85 30 ( lift mechanism req.) 0F00.N5 3 470 0F00.N5 47 880 0F500.N5 780 440 0F800.N5 40 300 (3 lift mechanisms req.) 0F800.N5 Cover set Right and left cover plate Non-handed cover cap (qty ) Cover set 0F8000.NA Telescopic arm set Telescopic arm (qty ) Cabinet heights 479 (8-7/8") 558 (") 0F300 558 (") 686 (7") 0F3500 686 (7") 889 (35") 0F3800 889 (35") 067 (4") 0F3900 Narrow aluminum door hardware set 7T550A.TL CLIP top free swing narrow alum. top door hinge (qty ) 78Z550AT CLIP top narrow aluminum bottom door hinge (qty ) 75H5400 Top door mounting plate (qty ) 75H5A00 Bottom door mounting plate (qty ) 75H5B00 Telescopic arm mounting plate (qty 4) 669.0 Aluminum screw for the bottom door mounting plate, bottom hinge, top hinge and telescopic arm mounting plate (qty 8) NOTE: Three hinges and mounting plates are required for cabinet widths over 9 (48 ) or combined door weight of 6.5 lb Narrow aluminum door hardware set Installation screw for top mounting plate 78Z550ATA5 606N or 606P without notice. 00
Assembly WARNING Risk of injury from spring-loaded arm Do not push lever arm down or leave in the down position Remove mechanism before installing or removing cabinet Locating pin locations 5 Y TR 9 37 TDH TR = Top reveal TDH = Top door ht. Top door height (TDH) Y 3 to 7 TDH x.6-8 + TR 7 to 53 TDH x.6-57 + TR Universal individual template is available for pre-boring 5 mm locating pins 65.05.0 without notice. 00
Attach the lift mechanism a. Use the AVENTOS template to prebore the locating pin holes for the AVENTOS HF lift mechanism. b. After aligning the lift mechanism with the cabinet using the locator pins,attach the mechanism with the four mounting screws provided. #7 x 35mm (-3/8 ) wood screws (qty 5) 3 Attach the telescopic arms WARNING: Risk of injury from spring loaded arm. Attach telescopic arms by clipping them on in the fully upright position. without notice. 00 3
Assembly 5 Top door hinge planning.7 5 9 66 Aluminum door hinge In-line mounting plate 7T550A 75H500.05 6 Bottom door hinge planning 3 66 Aluminum door bottom hinge Bottom door mounting plate 78Z550AT 75H5A00 4 without notice. 00
7 Frame preparation 90 0. 7. R 4.4 9 - R4 6.4 38 3.5 6 7.4 38 44 4 8 Bottom door planning X TDH Top door height (TDH) 3 to 7 TDH x.5 + 70 7 to 53 TDH x.5 + 47 X NOTE: 3 hinges are required for cabinet width over 9 mm (48") or 6.5 lb. combined door weight min. 7 Telescopic arm mounting plate 75H5B00 without notice. 00 5
Assembly 9 Attach the top door Determine the locations of mounting plates and hinges and attach the hardware to cabinet doors. Attach top door to the cabinet. 0 Attach the bottom door Attach bottom door to the top door and attach the telescopic arms. 6 without notice. 00
Adjust the top door hinge Adjust each top door hinge and mounting plate to properly align the top door to the cabinet. ± 3 mm ± mm + 3/- mm Adjust the bottom door hinge Adjust each bottom door hinge and mounting plate to properly align doors to the cabinet and to the top door. ±.5 mm ± mm ± mm without notice. 00 7
Assembly 3 Finalize the tension adjustments Use #x POZI bit Close and flush doors to cabinet. Open and close door to test closing force. Open door and adjust tension screws on both lift mechanisms with a power drill. Test door again and repeat until desired function is achieved. Tension adjustment should be the same on both lift mechanisms. Lock telescopic arms Open door enough to lock levers. Close and flush doors to cabinet. While pressing on the bottom of the top door, pull the bottom door open one inch.. Slightly open door and lock the telescopic arms into position using the levers as shown. 8 without notice. 00
5 Attach cover caps Attach the left and right cover plates to each lift mechanism then attach the symmetrical cover caps. without notice. 00 9
Removal WARNING Risk of injury from spring-loaded arm Do not push lever arm down or leave in the down position Remove mechanism before installing or removing cabinet Removing the covers Removing the door Release both arms and gently rest the top door on the loose arms. The tension will hold the doors up for the next step. 0 without notice. 00
3 Removing the doors. Hold the bottom door while unclipping the bottom hinge.. Hold the top door while detaching the top hinges. Simply unclip them if using the CLIP top hinges or unscrew them if using COMPACT. 4 Removing the telescopic arms Using a screwdriver, depress the release tabs to remove telescopic arms. If transporting the cabinet to the jobsite, stop here. Lift mechanisms can stay inside the cabinet for easy transport. without notice. 00
Other information Door clearance above cabinet Inch mm /3.03 /6.063.5 Z TDH Z = TDH x.44 + 3 3 /3.094 /8.5 3 5 /3.56 4 3 /6.88 5 7 /3.9 5.5 /4.5 6 9 /3.8 7 5 /6.33 8 /3.344 9 3 /8.375 9.5 3 /3.406 0 7 /6.438 5 /3.469 /.5 3 7 /3.53 3.5 9 /6.563 4 9 /3.594 5 5 /8.65 6 /3.656 7 /6.688 7.5 3 /3.79 8 3 /4.75 9 5 /3.78 0 3 /6.83 0.5 7 /3.844 Blum, Inc. 7733 Old Plank Rd. Stanley, NC 864 800-438-6788 fax 704-87-0799 www.blum.com 7 /8.875 9 /3.906 3 5 /6.938 4 3 /3.969 4.5 5.4 INST-AVT03.06.0