SERVO-DRIVE for AVENTOS HF. Technical data sheet.

Transcription

1 Technical data sheet

2 Ordering information Wooden fronts and wide alu frames symmetrical / asymmetrical types of lift mechanisms are enough to cover a wide range of applications. Using the power factor, you can calculate the required lift mechanisms. The power factor required depends on the weight of the lower and upper front and the cabinet height. The power factor and the door weight can be increased by 50% when a third lift mechanism is used. The larger front must be at the top for asymmetrical fronts. Standard SERVO-DRIVE This is how it s done! Symmetrical fronts: Power factor = cabinet height (KH) [mm] x door weight Asymmetrical fronts: Theoretical cabinet height (TKH) = upper front height (FHo) x 2 (including gaps) LF F F F LF LF LF F F LF Lift mechanism one-sided Lift mechanism two-sided Additional rd lift mechanism A trial application is recommended when you are in a borderline area for the individual lift mechanism. We recommend two synchronised drive units for a power factor > 17,250. LF Power factor 1 Symmetrical lift mechanism 2 Telescopic arm symmetrical Power factor LF Nickel plated steel F Cabinet height 2) mm F l + r 20F F Cabinet height 2) mm l + r 20F501 Cabinet height 2) mm l + r 20F801 Cabinet height 2) 70-1,040 mm l + r 20F901 2) "Theoretical cabinet height" for asymmetrical fronts 2

3 Ordering information Wooden fronts and wide alu frames symmetrical / asymmetrical a SERVO-DRIVE cover cap large left Nylon light grey / silk white Left 21F8001 b, c, d, 7, 9, 8 Distribution cable, connecting node, cable end protector, Blum transformer, flex and transformer unit housing See page 15 b Cover plate right ) Use chipboard screws (09.1x00) for wooden fronts. Use self tapping screws (08.085) for wide alu frames. Nylon light grey / silk white 10 CLIP top 120 hinge Right 20F8001 Boss: Steel boss Screws ) Unsprung 70T5550.TL c Cover cap round Boss: Steel boss Unsprung 70T5580.TL Nylon deep grey Plain 2 x 20F9001 Boss: Steel boss Unsprung 70T558E.TL Printed with the BLUM Logo 2 x 20F9001.BL can be printed with customer logo - minimums from 1,000 pcs Boss: Steel boss INSERTA Unsprung 70T5590BTL d SERVO-DRIVE switch light grey / silk white 2 x 21P CLIP top centre hinge Boss: Zinc boss Screws ) unsprung 78Z5500T e Blum distance bumper Boss: Zinc boss Unsprung 78Z550T RAL 707 dust grey Ø 5 mm x Boss: Zinc boss unsprung 78Z55ET Ø 8 mm x Mounting plate for CLIP top centre hinge 4 Mounting plate for telescopic arm Standard mounting plates with 0 mm distance All horizontal mounting plates with 0 mm distance Screws ) 175H5400 Recommendation 177H5100 Screws ) 175H H5400E 177H H5400E Only use a cruciform mounting plate for wide alu frames under a 55 mm frame width 5 Mounting plate for CLIP top 120 hinge Opening angle stop Standard mounting plates, spacing depends on the top gap Nylon, dark grey F7051 Screws ) 175H F H H5400E a SERVO-DRIVE drive unit Bit PZ cross slot RAL 707 dust grey Size 2, length 9 mm BIT-PZ KS2 21FA001

4 Ordering information Wooden fronts and wide alu frames symmetrical / asymmetrical Instruction leaflet and installation instructions Including documentation for the Machine Directive German English French Italian Spanish Bulgarian Chinese Danish Estonian Finnish Greek Japanese Croatian Latvian Lithuanian Dutch Norwegian Polish Portuguese Romanian Russian Swedish Serbian Slovakian Slovenian Czech Turkish Hungarian * Available starting 01/2010 MA-021/01DE MA-021/01EN MA-021/01FR MA-021/01IT MA-021/01ES MA-021/01BG* MA-021/01ZH* MA-021/01DA* MA-021/01ET* MA-021/01FI* MA-021/01EL* MA-021/01JA* MA-021/01HR* MA-021/01LV* MA-021/01LT* MA-021/01NL* MA-021/01NO* MA-021/01PL* MA-021/01PT* MA-021/01RO* MA-021/01RU* MA-021/01SV* MA-021/01SR* MA-021/01SK* MA-021/01SL* MA-021/01CS* MA-021/01TR* MA-021/01HU* 4

5 KH X SERVO-DRIVE for AVENTOS HF Planning Symmetrical wooden fronts and wide alu frames Drilling for mechanism and cable Fixing positions for lift mechanism Space requirement * H Ø 5* 5 Ø10** 52 Ø * Drilling depth 5 mm ** Alternative drilling Cabinet height KH H 4 x chipboard screws, Ø 4 x 5 mm KH Cabinet height mm KH x mm mm KH x mm Only on the left side Front assembly CLIP top 120 hinge unsprung CLIP top centre hinge SFA Side front overlay Cabinet height KH /2 1/2 SFA hinges starting at cabinet width 1,200 mm and/or 12 kg front weight 4 hinges starting at cabinet width 1800 mm and/or 20 kg door weight X Screw-on/ X mm 8 mm 70 mm mm 45 mm 47 mm F Gap Drilling distance TB Front overlay FA Mounting plate Min. gap F = 1.5 mm Drilling distance TB Centre gap F TB - F * Depends on mounting plate (e.g. 7 mm for cruciform mounting plate) 0 9 Mounting plate Screw-on INSERTA/knock-in/ assembly Space requirement - 5 min min 12. (12.8) Y FH OEB = Opening angle stop 45 () INSERTA Without OEB OEB 104 Y = FH x Y = FH x OEB 8 Y = 0 5

6 Planning Symmetrical wooden fronts and wide alu frames SERVO-DRIVE switch Blum distance bumper drilling position Blum distance bumper * From cabinet front edge for fronts that protrude below Recommendation for aluminium frames: Consider drilling for the Blum distance bumper in the cabinet side. A trial application must be carried out when fixing the Blum distance bumper to the front. Do not glue Blum distance bumper.

7 Y SERVO-DRIVE for AVENTOS HF Planning Asymmetrical wooden fronts and wide alu frames Drilling for mechanism and cable Fixing positions for lift mechanism Space requirement * Drilling depth 5 mm ** Alternative drilling TKH H mm TKH x mm mm TKH x mm TKH Theoretical cabinet height 4 x chipboard screws, Ø 4 x 5 mm KH Cabinet height FHo Upper front height FHu Lower front height Only on the left side Front assembly CLIP top 120 hinge unsprung CLIP top centre hinge 21 FHo Upper front height TKH Theoretical cabinet height SFA Side front overlay TKH X Screw-on/ mm FHo/2 + 8 mm mm FHo/ mm X FHo/ mm FHo/ mm F Gap Drilling distance TB Front overlay FA Mounting plate * TB - F Drilling distance TB Centre gap F Mounting plate * Depends on mounting plate (e.g. 7 mm for cruciform mounting plate) Min. gap F = 1.5 mm Min. lower front height Number of Hinges Space requirement X FAu hinges starting at cabinet width 1200 mm and/or 12 kg door weight 4 hinges starting at cabinet width 1800 mm and/or 20 kg door weight FH FAu Lower front overlay Screw-on INSERTA/knock-in/ assembly - min min 12. (12.8) OEB = Opening angle stop Without OEB OEB 104 Y = FH x Y = FH x () INSERTA OEB 8 Y = 0 7

8 Planning Asymmetrical wooden fronts and wide alu frames SERVO-DRIVE switch Blum distance bumper drilling position Blum distance bumper * From cabinet front edge for fronts that protrude below Recommendation for aluminium frames: Consider drilling for the Blum distance bumper in the cabinet side. A trial application must be carried out when fixing the Blum distance bumper to the front. Do not glue Blum distance bumper. 8

9 SERVO-DRIVE for AVENTOS HF Ordering information Symmetrical / asymmetrical narrow alu frames types of lift mechanisms are enough to cover a wide range of applications. Using the power factor, you can calculate the required lift mechanisms. The power factor required depends on the weight of the lower and upper front and the cabinet height. The larger front must be at the top for asymmetrical fronts. Standard SERVO-DRIVE This is how it s Symmetrical fronts: done! SFlbPower factor = cabinet height (KH) [mm] x door weight Asymmetrical fronts: Theoretical cabinet height (TKH) = upper front height (FHo) x 2 (including gaps) LF LF F F F LF Lift mechanism one-sided 20F LF Lift mechanism two-sided LF Power factor A trial application is recommended when you are in a borderline area for the individual lift mechanism. 1 2 Symmetrical lift mechanism Telescopic arm symmetrical Nickel plated steel Power factor LF F F F Cabinet height mm l+r 20F201 Cabinet height mm l+r 20F501 l+r 20F801 Cabinet height mm a SERVO-DRIVE cover cap large left Nylon light grey / silk white Cabinet height 70-1,040 mm Left 21F8001 l+r 9 20F901 "Theoretical cabinet height" for asymmetrical fronts

10 Ordering information Symmetrical / asymmetrical narrow alu frames b Cover plate right 11 CLIP top alu frame centre hinge Nylon light grey / silk white Right 20F8001 Boss: Zinc boss Screw-on unsprung 78Z550AT 12 CLIP adapter plate for centre hinges c Cover cap round Symmetrical 175H5A00 Nylon deep grey Plain 2 x 20F9001 Printed with the BLUM Logo 2 x 20F9001.BL Opening angle stop can be printed with customer logo -minimums from pcs Nylon, dark grey F F7011 d SERVO-DRIVE switch light grey / silk white Instruction leaflet and installation instructions 2 x 21P5020 Including documentation for the Machine Directive German MA-021/01DE e Blum distance bumper English MA-021/01EN RAL 707 dust grey French MA-021/01FR Ø 5 mm x Italian MA-021/01IT Ø 8 mm x Spanish MA-021/01ES Bulgarian MA-021/01BG* 4 CLIP adapter plate for telescopic arms Chinese MA-021/01ZH* left/right 175H5B00 Danish MA-021/01DA* Estonian MA-021/01ET* Finnish MA-021/01FI* 5 Mounting plate for CLIP top 120 hinge Greek MA-021/01EL* Standard mounting plates, spacing depends on the top gap Japanese MA-021/01JA* Croatian MA-021/01HR* Screw-on 175H5400 Latvian MA-021/01LV* 177H5100 Lithuanian MA-021/01LT* 177H5400E Dutch MA-021/01NL* Norwegian MA-021/01NO* a SERVO-DRIVE drive unit Polish MA-021/01PL* RAL 707 dust grey Portuguese MA-021/01PT* 21FA001 Romanian MA-021/01RO* Russian MA-021/01RU* Swedish MA-021/01SV* b, c, d, 7, 9, 8 Distribution cable, connecting node, cable end protector, Blum transformer, flex and transformer unit housing Serbian Slovakian MA-021/01SR* MA-021/01SK* Slovenian MA-021/01SL* See page 15 Czech MA-021/01CS* Turkish MA-021/01TR* 10 CLIP top 120 alu frame hinge Hungarian MA-021/01HU* Boss: Zinc boss Screw-on unsprung 72T550A.TL * Available starting 01/2010 Bit PZ cross slot BIT-PZ KS2 Size 2, length 9 mm 10

11 Planning Symmetrical narrow alu frames Drilling for mechanism and cable Fixing positions for lift mechanism Space requirement H Ø 5* /2 X 1/2 KH Ø10** 52 Ø10 * Drilling depth 5 mm ** Alternative drilling Cabinet height KH H mm KH x mm mm KH x mm 4 x chipboard screws, Ø 4 x 5 mm KH Cabinet height Only on the left side Front assembly CLIP top 120 alu frame hinge unsprung CLIP top alu frame centre hinge hinges starting at cabinet width 1,200 mm and/or 12 kg front weight cabinet width 1,800 mm and/or 20 kg front weight Cabinet height KH X mm 54 mm mm 1 mm Min. gap F = 1.5 mm An adjustment has to be made for frame thicknesses over 20.5 mm Front assembly Space requirement * When changing material thickness, adjust the assembly dimensions accordingly Y FH OEB = Opening angle stop R4 1.4 Without OEB OEB 104 OEB 8 Y = FH x Y = FH x Y = 0 11

12 Planning Symmetrical narrow alu frames SERVO-DRIVE switch Blum distance bumper drilling position Blum distance bumper * From cabinet front edge for fronts that protrude below Recommendation for aluminium frames: Consider drilling for the Blum distance bumper in the cabinet side. A trial application must be carried out when fixing the Blum distance bumper to the front. Do not glue Blum distance bumper. 12

13 Y SERVO-DRIVE for AVENTOS HF Planning Asymmetrical narrow alu frames Drilling for mechanism and cable Fixing positions for lift mechanism Space requirement min 278 H Ø 5* 5 Ø FHo min 22 FHu Ø10** TKH * Drilling depth 5 mm **Alternative drilling TKH H mm TKH x mm mm TKH x mm TKH Theoretical cabinet height 4 x chipboard screws, Ø 4 x 5 mm KH Cabinet height FHo Upper front height FHu Lower front height Only on the left side Front assembly CLIP top 120 alu frame hinge unsprung CLIP top alu frame centre hinge FHo Upper front height TKH Theoretical cabinet height TKH X mm FHo/ mm mm FHo/2 + 1 mm Min. gap F = 1.5 mm An adjustment has to be made for frame thicknesses over 20.5 mm Min. lower front height Number of Hinges Space requirement X + + FAu hinges starting at cabinet width 1200 mm and/or 12 kg door weight 4 hinges starting at cabinet width 1800 mm and/or 20 kg door weight FH FAu Lower front overlay Screw-on * When changing material thickness, adjust the assembly dimensions accordingly OEB = Opening angle stop Without OEB Y = FH x R OEB 104 OEB 8 Y = FH x Y = 0 1

14 Planning Asymmetrical narrow alu frames SERVO-DRIVE switch Blum distance bumper drilling position Blum distance bumper * From cabinet front edge for fronts that protrude below Recommendation for aluminium frames: Consider drilling for the Blum distance bumper in the cabinet side. A trial application must be carried out when fixing the Blum distance bumper to the front. Do not glue Blum distance bumper. 14

15 Order specifications Blum transformer (100 Watt) and accessories For all applications b c 8 d 7 9 b Distribution cable for cutting to size 9 Flex 1 x 100 m Z10K1HMA Flex Europe Z10M200E 1/10 x m Z10K00A Flex CH Z10M200C 1/10 x 8 m Z10K800AE Flex US, CA Z10M200U Can be used as a distribution cable Flex JP Z10M200J Flex BR Z10M200S c Connecting node Flex BR Z10M200S.01 Black Flex UK Z10M200B 50 Stk. Z10V1000 Flex DK Z10M200D Flex IL Z10M200I Flex AU Z10M200K d Cable end protector Flex CN Z10M200N RAL 707 dust grey Flex AR Z10M200A 100 Stk. Z10K0008 Flex IN Z10M200H Flex CL Z10M200L Flex TW Z10M200T 7 Blum transformer Flex ZA Z10M200Z 100 W 10 Stk. Z10NE Flex Europe without plug Z10M200E.OS Only 1 Blum transformer permitted per distribution cable Flex US, CA without plug Z10M200U.OS Cable holder 8 Transformer unit housing for panel fixing White 100 pcs. Z10K0009 RAL 707 dust grey Z10NG100 15