DOUBLE ACTING CYLINDERS, 3 to 100 mm CONFORMING TO VDMA 456 - ISO 6431 STANDARDS SERIES 453 - TYPE: PES for flush-mount position detectors for explosive atmospheres caused by gases or dust, zones 1-1 and - II GD c - Ta 40 C T85 C (T6) - Ta 70 C T100 C (T5) ATEX P11-9-GB-Rb
DOUBLE ACTING PNEUMATIC CYLINDERS - TYPE PES WITH PROFILED BARREL EASY FITTING Large choice of standard fittings and rod ends. PNEUMATIC CUSHIONING with large cushioning length. T-SLOT AND DOVETAIL GROOVES Grooves in 4 different positions (to be specified on order). ACCURATE CUSHIONING by means of micrometer screws (captive screws). ESTHETIC DESIGN Cylinders with profiled barrel in hard-anodized aluminium. BARREL/END CONNECTION WITH TIE-RODS (80-100) STURDY DESIGN Rod in hard chrome steel. ACCURATE ROD GUIDING by means of a highperformance selflubricating bearing and non-abrasive scraper seal. EASY MAINTENANCE PES cylinders do not require any lubrication. STANDARD SWIVEL TRUNNION MOUNT As a fastening option this trunnion slides on the barrel for on-site positioning. POSITION DETECTOR REED switch or magnetoresistive (MR) type for assembly into dovetail groove. Barrel/end connection with tierods on cylinders 80-100 mm EASY POSITION DETECTOR MOUNTING PES CYLINDER WITH "COMPACT" DETECTOR FOR ASSEMBLY INTO DOVETAIL GROOVE (see leaflet P11-93) Cable cover and holder P11-9-
POSITION OF THE T-SLOT AND THE DOVETAIL GROOVES Series 453 PES cylinders offer the advantage of being able to position the T-slot grooves on the cylinder in 4 different positions with reference to the axes of the pressure supply ports. The position must be specified when defining the cylinder code. Number of grooves per diameter: 3 mm 1 T-slot groove - dovetail grooves 40 to 63 T-slot grooves - 3 dovetail grooves 80-100 T-slot grooves - 7 dovetail grooves STANDARD POSITION Axis of the supply ports Pressure supply ports and T-slot grooves OTHER POSSIBLE POSITIONS (consult us) 1 O'CLOCK POSITION (standard) 3 O'CLOCK POSITION 6 O'CLOCK POSITION 9 O'CLOCK POSITION Pressure supply ports Pressure supply ports Pressure supply ports T-slot grooves RANGE OF STANDARD MOUNTINGS T-slot grooves T-slot grooves Front flange Rear flange Feet Cap, detachable clevis, or with spherical eye Cap, detachable eye, or with spherical eye Angular clevis bracket, or with sperical eye Centre trunnion Trunnion supports Sperical bearing P11-9-3 11
VDMA-AFNOR-ISO AIR CYLINDERS 3 to 100 mm MAGNETIC DETECTION AH AL MT The cylinder type PES, dia. 3 to 100 mm, onto which detectors can be mounted, has a force line spectrum according to CNOMO E 530 5 809. Field values: 7.5 m Tesla at point MT and a maximum of m Tesla at the fringe of the force line spectrum (1 m Tesla approx. 10 Gauss). vérin 3 40 50 63 80 100 AH 6 6 7 8 9 6 AL 8 9 10 10 11 1 mm Optimal position detection is guaranteed when using our ATEX COMPACT detectors: reed switch or magneto-resistive (MR) type, see P11-93. Air cylinders equipped with a magnet (M) designed to operate in combination with magnetic position detectors (DM). These air cylinders can be equipped with one or more magnetic position detectors (without contact) attached to the barrel. They allow limit positions and intermediate piston positions to be detected. (M) DEFINING THE PART NUMBER OF A 3 TO 100 mm AFNOR/VDMA/ISO AIR CYLINDER Air cylinder type: prefix PES Air cylinder diameter (in mm) Cylinder with profiled barrel : suffix P Adjustable pneumatic end-of-stroke cushioning: suffix A Non-cushioned (elastic cushioning): suffix NA Length of stroke(in mm) Air cylinder designed to receive magnetic position detectors (non-magnetic barrel) suffix DM PES.. P A/NA... DM ORDERING When ordering, please specify (for more details see page P9-7) : AIR CYLINDER The air cylinder standard code or part number The ATEX OPTION code zone 1-1 : 61017 or zone - : 61014 The code or part number of any option(s) MOUNTINGS The code or codes and quantity of any mountings 450..... + 61 01. : 434..... +...... DETECTORS The code and quantity of any magnetic detectors : 881..... The code and quantity of mountings : 881..... CONTENTS Standardisation of dimensions and interchangeability P11-9-5 Defining the diameter of a cylinder P11-9-6 Double acting air cylinders 3-100 mm P11-9-7 Mountings P11-9-8 Overall dimensions P11-9-10 P11-9-4
STANDARDIZATION OF DIMENSIONS AND INTERCHANGEABILITY STANDARDS OF CYLINDERS 3 to 30 mm INTERCHANGEABILITY within the standard between standards ISO 6431 (year: 1983) The international standards define a cylinder unit equipped with its mountings without any specifications relative to the bare cylinder alone. Interchangeability between manufacturers is achieved by replacing both the cylinder and its mountings. AH AB SA+ XA+ A0 TR JOUCOMATIC''s cylinder, type PES series 450-453, complies with this standard. AFNOR NFE 49003 - VDMA 456 (year: 199) The new standards first define all the external dimensions of a bare cylinder and then the mountings which, when mounted, must comply with the above unit (ISO 6431 cylinder). Full interchangeability between the manufacturers is achieved at every level: bare cylinder, each mounting, complete unit. For full interchangeability with ISO 6431, the VDMA- AFNOR NFE 49003 cylinder must be equipped with its mountings, and vice versa. JOUCOMATIC's cylinder, type PES series 450-453, complies with this standard. CNOMO 06.07.0/AFNOR NFE 49001 (year: 1968) The French standards first define all the external dimensions of a bare cylinder and then the mountings. Full interchangeability between the manufacturers is possible at every level: bare cylinder, each mounting, complete unit. No interchangeability can be achieved between the CNOMO/NFE 49001 cylinder (bare or equipped) and the AFNOR NFE 49003 or ISO 6431 cylinder, and vice versa. JOUCOMATIC's cylinder, type PCN, complies with this standard. Note: ISO 643 and AFNOR NFE 49030 standards apply only to mini-cylinders 8 to 5 mm. 11 P11-9-5
DEFINITION OF THE DIAMETER OF A CYLINDER THE DYNAMIC EFFORT DEVELOPED BY A CYLINDER F Pressure x piston area x efficiency The efficiency of a cylinder depends on the diameter of the cylinder, on the pressure and on its mechanical construction. The graph and a chart below show the dynamic effort developed by a cylinder at the piston rod, at various supply pressures. LOAD FACTOR This is the relationship expressed as a percentage between the actual load being moved by the cylinder and the dynamic effort available at the end of the piston rod. actual load Load factor (in %) x 100 dynamic effort For an optimum installation of a cylinder, we recommend a cylinder with a load factor inferior or equal to 75%. EXAMPLE: Calculate a cylinder to lift a load of 130 dan with a pressure of 7 bar (gauge pressure). Theoretical actual load 130 dynamic effort 175 dan Load factor 0.75 The graph below shows the cross over point between the dynamic effort and the supply pressure. The cylinder diameter required will be that where the curve passes this point or the cylinder giving a force immediately above that required. In the example above: 175 dan is between 50 and 63. The cylinder recommended is the 63 mm which will develop a force of 00 dan at 7 bar and the actual load factor is: 130 dan x 100 65% 00 dan 10 EFFORTS DEVELOPED AT THE END OF THE ROD EFFORTS DÉVELOPPÉS (ROD OUT) EN SORTIE DE TIGE EFFORTS DEVELOPED AT THE END OF THE ROD EFFORTS DÉVELOPPÉS (ROD RETURNED) EN RENTRÉE DE TIGE 10 8 8 Pression relative (en bar) 6 4 Pression relative (en bar) 6 4 3 40 50 63 80 100 3 40 50 63 80 100 1 3 5 10 0 50 100 175 00 Eff Dynamic t d effort i (in bar) ( d N) 500 1000 000 5000 1 3 5 10 0 50 100 00 500 Eff Dynamic t d effort i (in ( bar) d N) 1000 000 5000 EFFORTS DEVELOPED BY A CYLINDER (in dan) Piston cross- Dynamic effort developed (in dan) at various supply pressures (in bar) Cylinder Rod section area (cm ) 4 6 8 10 3 1 8 6.9 13 11 30 5 46 39 6 5 77 65 40 16 1.6 10.6 1 17 46 37 70 58 95 80 1 100 50 0 19.6 16.5 33 7 70 58 110 9 150 14 190 155 63 0 31. 8.1 53 46 110 98 170 154 30 11 90 64 80 5 50.3 45.4 88 77 185 163 85 55 385 341 480 47 100 5 78.5 73.5 135 15 90 60 440 400 600 550 750 675 Efforts developed with rod out (bottom side) Efforts developed with rod returned (rod side) Note: Cylinders with double crossbar develop identical efforts in both working directions. Their values are the ones defined above for efforts developed with rod returned. P11-9-6
Series 453 Type: PES-DM DOUBLE ACTING CYLINDERS 3 to 100 mm Conforming with VDMA - ISO - AFNOR standards With adjustable pneumatic cushioning Cylinders with profiled barrel for flush-mount detectors ATEX NS Cylinders intented for use in potentially explosive dusty atmospheres caused by gases, vapours, mists an/or dust ATEX directive 94/9/EC. CLASSIFICATION II 3 GD c-ta40 C T85 C (T6) - Ta70 C T100 C (T5) (ZONE -) II GD c-ta40 C T85 C (T6) - Ta70 C T100 C (T5) (ZONE 1-1) Compliance with the Essential Health and Safety Requirements has been assured by compliance with European Standards EN 13463-1 and pren 13463-5 SPECIFICATION FLUID : air or neutral gas, filtered, lubricated or not PRESSURE : 10 bar max. TEMPERATURE : 0 C to + 70 C (for higher temperatures, consult us) OPTIMAL MAX. SPEED : 1 m/s (for optimal service life) MAX. SPEED RATE : m/s STANDARDS : VDMA 456 - ISO 6431 - AFNOR NFE 49003 CONSTRUCTION Barrel Front and rear ends Barrel/end connection Bearing Cushioning seals Cushioning Rod Rod nut Piston Piston seal : non-magnetic, hard anodized aluminium alloy : aluminium alloy : with stainless steel tie-rods - 80 to 100 mm : self-lubricating metal : polyurethane (PUR) : pneumatic, adjustable from both sides with captive screws : hard chrome plated steel : galvanized steel : acetal resin (POM), or light alloy fitted with an annular permanent magnet : polyurethane (PUR) CHOICE OF EQUIPMENT DEFINING THE CYLINDER CODE Standard version: profiled barrel with adjustable pneumatic cushioning, equipped for magnetic position detectors (T-slot grooves in 1 o'clock position). Other versions available (see tables below). When ordering, please specify: AIR CYLINDER - The air cylinder type (profiled, with or without cushioning, equipped or not for magnetic position detection). - The position of the T-slot groove on the cylinder. - The cylinder diameter and its stroke. - ATEX OPTION zone 1-1 : 61017 or zone - : 61014 DETECTORS: The magnetic position detectors must be ordered separately: - ATEX COMPACT model, Reed switch or magneto-resistive type (see leaflet P11-93) Barrel Profiled barrel TYPE DE VERIN Cushioning Cushioned Non-cushioned GROOVE POSITION Position of the T-slot grooves on the profiled PES cylinder (1) Available versions (consult us) Position detection Equipped Non-equipped Equipped Non-equipped 1 o'clock 3 o'clock 6 o'clock 9 o'clock 453 5........ Type 00 01 0 03 Type 0 3 6 9 CYLINDER Type bore 3 3 4 40 5 50 6 63 8 80 1 100 Ordering example: - profiled cylinder with pneumatic cushioning equipped for detectors 00 - T-slot grooves at 3 o'clock position 3 - Cylinder 80 mm 8 - Stroke 100 mm 0100 - ATEX OPTION code zone 1-1 : 61017 or zone - : 61014. Ordering code: 453 5 00 3 8 0100 + 61014 ACCESSORY: Protective groove cover and detector cable holder - see leaflet P9 or P93 (1) (1) (1) (1) (1) (1) Standard strokes () (recommended standard strokes) 5 50 80 100 15 160 00 50 30 400 500 630 700 800 900 1000 3 40 50-63 80 100 () Other strokes on request. MOUNTINGS: see following pages OPTIONS: - Version with through-rod (consult us) - Round cylinder with tie-rods - aluminium barre (consult us) - Cylinder with rod lock (consult us) - Other versions (consult us) Max. strokes : The codes in the grey shaded areas correspond to commonly used products which can be supplied rapidly 1000 1500 1800 000 000 P11-9-7 11
Series 453 MOUNTINGS Rectangular Centre trunnion MT4 Supports () Low feet () High foot (1) front or rear flange (for PES cylinder with profiled barrel) for centre trunnion MS1 MS3 MF1 - MF fixed mount / XV (3) movable mount (4) AT4 Application Standard duty Heavy duty Construction For cylinder Stamped sheet steel Drawn steel Steel Cast iron Cast iron Aluminium + bush CODES OF MOUNTINGS 3 434 00 163 434 00 307 434 00 119 410 564 410 570 434 00 07 40 434 00 164 434 00 308 434 00 10 410 565 410 571 434 00 08 50 434 00 165 434 00 309 434 00 11 410 566 410 57 434 00 08 63 434 00 166 434 00 310 434 00 1 410 567 410 573 434 00 09 80 434 00 167 434 00 311 434 00 13 410 568 410 574 434 00 09 100 434 00 168 434 00 31 434 00 14 410 569 410 575 434 00 10 Dimensions page 11 page 17 page 11 page 16 page 16 page 16 Application Standard duty Heavy duty Angular Cap, detachable clevis Cap, detachable eye (trunnion) clevis bracket MP MP4 AB3 Light Cast iron+steel Cast iron+steel Light Cast iron Cast iron Light Cast iron Cast iron alloy without bush + bush alloy without bush + bush alloy without bush + bush 3 434 00 130 434 00 57 434 00 185 434 00 15 434 00 66 434 00 171 434 00 383 434 00 145 434 00 110 40 434 00 131 434 00 58 434 00 186 434 00 16 434 00 67 434 00 17 434 00 384 434 00 146 434 00 111 50 434 00 13 434 00 59 434 00 187 434 00 17 434 00 68 434 00 173 434 00 385 434 00 147 434 00 11 63 434 00 133 434 00 60 434 00 188 434 00 18 434 00 69 434 00 174 434 00 386 434 00 148 434 00 113 80 434 00 134 434 00 61 434 00 189 434 00 19 434 00 70 434 00 175 434 00 387 434 00 149 434 00 114 100 434 00 135 434 00 6 434 00 190 434 00 161 434 00 71 434 00 176 434 00 388 434 00 150 434 00 115 Dimensions pages 1/13 pages 1/13 page 13 (1) High foot sold individually. () Corresponds to a set of parts. (3) Trunnion supplied fixed to the barrel at dimension XV specified on order: The code of the fixed-mount centre trunnion and the dimension XV along with the positioning code of the trunnion with respect to the ports must be added to the cylinder code. (Example: 453 50 003 000 + options 410 566 / XV 10 mm + 410 00) (4) Trunnion supplied loose on cylinder barrel for on-site adjustment to required dimension: The code of the movable-mount centre trunnion and the dimension XV along with the positioning code of the trunnion with respect to the ports must be added to the cylinder code. NOTE: With the exception of the centre trunnion, mountings are delivered separately. Centre trunnion position Trunnion axis is perpendicular to supply ports, code: 410 00 (standard position) Other position upon request, code: 410 003 410 00 410 003 P11-9-8 : The codes in the grey shaded areas correspond to commonly used products which can be supplied rapidly
11 Series 453 MOUNTINGS Cap, clevis Angular clevis Female Spherical for spherical eye Cap, eye with bracket rod clevis rod end Alignment (6) or spherical bearing (5) spherical eye (5) ISO 8140 - RP10P ISO 8139 - RP103P compensator clevis bracket MP6 AB5 AP AP6 Application Standard duty Heavy duty Construction Forged steel Forged steel Forged steel Steel Steel Steel For cylinder CODES OF MOUNTINGS 3 434 00 363 434 00 37 434 00 354 434 00 016 434 00 001 434 00 4 40 434 00 364 434 00 373 434 00 355 434 00 017 434 00 00 434 00 43 50 434 00 365 434 00 374 434 00 356 434 00 018 434 00 003 434 00 44 63 434 00 366 434 00 375 434 00 357 434 00 018 434 00 003 434 00 44 80 434 00 367 434 00 376 434 00 358 434 00 019 434 00 004 434 00 45 100 434 00 368 434 00 377 434 00 359 434 00 019 434 00 004 434 00 45 Dimensions pages 14/15 pages 14/15 page 15 page 18 page 18 page 18 (5) These accessories allow for a spherical angular compensation of 4. (6) This accessory allows for a spherical angular compensation of 4 and a radial compensation of 0.7 mm. NOTE: With the exception of the centre trunnion, mountings are delivered separately. : The codes in the grey shaded areas correspond to commonly used products which can be supplied rapidly P11-9-9
Series 453 DIMENSIONS AND WEIGHTS - BARE CYLINDER N + 1 AM M ZJ + 1 L8 + 1 BG RT KW WH L VD PL EE PL VA E E SINGLE ROD CYLINDER KK KV B d11 MM SW BA d11 AM ZM + AM THROUGH ROD TYPE CYLINDER M L8 + 1 M + 1 1 : + Stroke : + (stroke x ) : dimensions on flats DIMENSIONS AM B BA BG E EE KK KV KW L L8 M MM N PL RT SW VA 3 30 30 16 50 G1/8 M10x1.5 16 5 17 94 48 1 14 14 M6 10 3.5 4 4 40 4 35 35 16 55 G1/4 M1x1.5 18 6 19 105 54 16 159 16 M6 13 38 4 4 50 3 40 40 16 65 G1/4 M16x1.5 4 8 6 106 69 0 175 18.5 M8 16 46.5 4 4 63 3 45 45 16 79 G3/8 M16x1.5 4 8 6 11 69 0 190 17 M8 16 56.5 4 4 80 40 45 45 17 100 G3/8 M0x1.5 30 10 33 18 86 5 14 16.5 M10 1 7 4 4 100 40 55 55 17 10 G1/ M0x1.5 30 10 35.5 138 91 5 9 1 M10 1 89 4 4 VD mini DIMENSIONS WEIGHTS (kg) WH ZJ ZM (3) (4) 3 6 10 146 0.610 0.35 40 30 135 165 0.850 0.455 50 37 143 180 1.5 0.630 63 37 158 195 1.780 0.815 80 46 174 0.900 1.300 100 51 189 40 4.100 1.600 (3) Cylinder weight with 0 mm stroke. (4) Weight to be added per additional 100 mm length. P11-9-10
Series 453 LOW FEET MOUNTING - MS1 AM XA + 1 AT AH AB AU L8 + 1 SA + 1 AU AT AO max. TR RECTANGULAR FRONT OR REAR MOUNTING FLANGE - MF1 - MF AM ZF + 1 ZJ + 1 W MF d4 H11 R 4 FB TF UF max. 1 : + Stroke DIMENSIONS R AB AM AO AH AT AU d4 E FB L8 MF TR SA TF UF W XA ZJ ZF 3 7 11 3 4.5 4 30 50 7 94 10 3 14 64 3.5 86 16 144 10 130 40 10 4 15 36 4.5 8 35 58 9 105 10 36 161 7 38 96 0 163 135 145 50 10 3 15 45 5.5 3 40 70 9 106 1 45 170 90 46.5 115 5 175 143 155 63 10 3 15 50 5.5 3 45 85 9 11 1 50 185 100 56.5 130 5 190 158 170 80 1 40 0 63 6.5 41 45 105 1 18 16 63 10 16 7 165 30 15 174 190 100 14.5 40 5 71 6.5 41 55 130 14 138 16 75 0 150 89 187 35 30 189 05 feet Front or rear flange 3 0.150 0.40 40 0.190 0.40 50 0.395 0.500 feet Front or rear flange 63 0.445 0.580 80 0.790 1.390 100 1.400 1.630 11 P11-9-11
Series 453 CAP, DETACHABLE CLEVIS MOUNTING - MP CB H14 AM XD + 1 FL MR max. CD H9/e8 UB h14 Y CAP, DETACHABLE EYE (TRUNNION) MOUNTING - MP4 EW AM XD + 1 FL MR max. max. E CD H9 1 : + Stroke DIMENSIONS AM CB CD E EW FL MR UB XD Y 3 6 10 50 6 11 3.5 45 14 56 40 4 8 1 58 8 5 13 38 5 160 63 50 3 3 1 70 3 7 13 46.5 60 170 71 63 3 40 16 85 40 3 17 56.5 70 190 81 80 40 50 16 105 50 36 17 7 90 10 101 100 40 60 0 130 60 41 1 89 110 30 18 Standard EW tolerances - 0. 3...100 mm EW - 0.6 Cap, detachable clevis Cap, detachable eye Cap, detachable eye Cap, detachable clevis (trunnion) (trunnion) Light alloy Cast iron+steel Light alloy Cast iron+steel Light alloy Cast iron+steel Light alloy Cast iron+steel 3 0.105 0.05 0.085 0.10 40 0.150 0.305 0.09 0.30 50 0.40 0.430 0.170 0.430 63 0.370 0.685 0.50 0.60 80 0.635 1.375 0.445 1.110 100 0.990.100 0.755 1.700 P11-9-1
Series 453 STRAIGHT COMPLETE TRUNNION MOUNTING - WITH OR WITHOUT BUSH - MP + MP4 To achieve the complete assembly, items MP and MP4 must be ordered separately. 4 D AM XD + 1 FL FL α α Y CD H9/e8 L65/1 COMPLETE TRUNNION MOUNTING WITH ANGULAR CLEVIS BRACKET - WITH OR WITHOUT BUSH - MP + AB3 This set includes the cap, detachable clevis MP and the angular clevis bracket AB3, with or without bush. These mountings must be ordered separately. AM XD + 1 G1 Js14 0 CA Js15 Y CD H9/e8 L65/ Standard EM tolerances 3...100 mm - 0. EM - 0.6 EM K1 K max. 1 : + Stroke 4 S5 G G3 max. DIMENSIONS AM CD D S5 E EM FL K1 K G1 G G3 CA L65/1 L65/ XD Y α 3 10 6.6 6.6 50 6 38 51 1 18 31 3 5.5 6.5 3.5 14 56 45 40 4 1 6.6 6.6 58 8 5 41 54 4 35 36 5.5 8.5 38 160 63 50 50 3 1 9 9 70 3 7 50 65 33 30 45 45 6.5 10.5 46.5 170 71 40 63 3 16 9 9 85 40 3 5 67 37 35 50 50 6.5 10.5 56.5 190 81 55 80 40 16 11 11 105 50 36 66 86 47 40 60 63 10 11.5 7 10 101 45 100 40 0 11 11 130 60 41 76 96 55 50 70 71 10 1.5 89 30 18 35 Straight complete Complete trunnion Straight complete Complete trunnion trunnion with ang. clevis bracket trunnion with ang. clevis bracket Light alloy Cast iron+steel Light alloy Cast iron+steel Light alloy Cast iron+steel Light alloy Cast iron+steel 3 0.190 0.415 0.160 0.340 40 0.40 0.535 0.30 0.450 50 0.410 0.860 0.390 0.790 63 0.60 1.305 0.570 1.080 80 1.080.485 0.950.090 100 1.745 3.800 1.500.750 11 P11-9-13
Series 453 CAP, DETACHABLE CLEVIS MOUNTING - FOR SPHERICAL EYE (STRAIGHT) OR ANGULAR CLEVIS BRACKET B1 D10 AM XD + 1 FL R1 max. CN F7/h9 B CAP, DETACHABLE EYE MOUNTING WITH SPHERICAL BEARING - MP6 +0 EN - 0,1 AM XD + 1 FL max. E 4 4 ER max. CN H7 B 1 : + Stroke DIMENSIONS AM B B1 B CN E ER EN FL R1 XD 3 10.5 14 34 10 50 15 14 11 3.5 14 40 4 1 16 40 1 58 18 16 5 13 38 160 50 3 15 1 45 16 70 0 1 7 18 46.5 170 63 3 15 1 51 16 85 3 1 3 18 56.5 190 80 40 18 5 65 0 105 7 5 36 7 10 100 40 18 5 75 0 130 30 5 41 89 30 Standard EN tolerances 0 3...100 mm EN - 0.1 Cap, detachable clevis Cap, detachable eye for spherical eye with spherical bearing 3 0.190 0.180 40 0.300 0.90 50 0.460 0.40 Cap, detachable clevis for spherical eye Cap, detachable eye with spherical bearing 63 0.680 0.650 80 1.460 1.10 100.130 1.870 P11-9-14
Series 453 STRAIGHT COMPLETE TRUNNION MOUNTING, SPHERICAL BEARING This set includes the cap, clevis for spherical eye and the cap, eye with spherical bearing MP6. These mountings must be ordered separately. 4 D AM XD + 1 FL FL α α CN H7/h9 L65/1 COMPLETE TRUNNION MOUNTING WITH ANGULAR CLEVIS BRACKET - SPHERICAL BEARING This set includes the cap, detachable eye and the angular clevis bracket spherical eye AB5. These mountings must be ordered separately. AM XD + 1 G1 Js14 180 10 CH Js15 CN H7/h9 4 K1 K max. 4 EN +0-0,1 L65/ 1 : + Stroke 4 S5 G G3 max. DIMENSIONS AM CN D S5 E EN FL K1 K G1 G G3 CH L65/1 L65/ XD α 3 10 6.6 6.6 50 14 38 51 1 18 31 3 5.5 8.5 3.5 14 40 40 4 1 6.6 6.6 58 16 5 41 54 4 35 36 5.5 8.5 38 160 45 50 3 16 9 9 70 1 7 50 65 33 30 45 45 6.5 10 46.5 170 35 63 3 16 9 9 85 1 3 5 67 37 35 50 50 6.5 10 56.5 190 50 80 40 0 11 11 105 5 36 66 86 47 40 60 63 10 11.5 7 10 40 100 40 0 11 11 130 5 41 76 96 55 50 70 71 10 1.5 89 30 30 Straight complete Complete trunnion trunnion,spherical bearing with spherical bearing 3 0.370 0.370 40 0.590 0.530 50 0.880 0.910 Straight complete trunnion,spherical bearing Complete trunnion with spherical bearing 63 1.330 1.00 80.670.400 100 4 3.00 11 P11-9-15
Series 453 CENTRE TRUNNION MOUNTING - MT4 AM XV ZJ + 1 Q 3 E UW TD e9 1 : + Stroke 1 + Stroke : Except when dimension XV is specified on order, the position of the trunnion may be adjusted along the unit. Consequently, the centre trunnion is not screwed on and must be adjusted after delivery. 3 : 8 locking screws SUPPORTS FOR CENTRE TRUNNION - AT4 TM h14 TL h14 3 70 76 + C 114 3 + 1 8 40 79 86 + C 14 41 + 1 83 50 86 95 + C 13 49 + 1 83 63 96 115 + C 147 64 + 1 83 80 10 10 + C 155 67 + 1 88 100 109 131 + C 165 75 + 1 90 WITHOUT DETECTORS XV XV XV XV 1 min. max. min. max. min. WITHOUT DETECTORS WITH "T" DETECTORS WITH "COMPACT" DETECTORS XV XV XV XV 1 min. max. min. max. min. 3 70 76 + C 105 41 + 1 64 40 79 86 + C 114 51 + 1 63 50 86 95 + C 1 59 + 1 63 63 96 115 + C 138 73 + 1 65 80 10 10 + C 145 77 + 1 68 100 109 131 + C 156 84 + 1 7 B1 A d4 H3 TM h14 L5 L6 TD H9 B1 A d3 B H1 C DIMENSIONS A AM B1 B C d3 d4 E H1 H3 L5 L6 Q TD TL TM UW ZJ 3 3 46 18 10.5 6.6 11 50 30 6.8 71 86 18 1 3.5 1 50 64 10 40 36 4 55 1 1 9 15 55 36 9 87 105 0 16 38 16 63 73 135 50 36 3 55 1 1 9 15 65 36 9 99 117 0 16 46.5 16 75 88 143 63 4 3 65 3 13 11 18 79 40 11 116 136 5 0 56.5 0 90 10 158 80 4 40 65 3 13 11 18 100 40 11 136 156 5 0 7 0 110 14 174 100 50 40 75 8.5 16 13.5 0 10 50 13 164 189 30 5 89 5 13 144 189 Centre trunnion Supports for centre trunnion Centre trunnion Supports for centre trunnion 3 0.170 0.10 40 0.315 0.30 50 0.465 0.30 63 0.575 0.330 80 1.095 0.330 100 1.500 0.580 P11-9-16
11 Series 453 HIGH FOOT MOUNTING - MS3 (sold individually) AM XA + 1 AT øab UF AH AH 1 : + Stroke AU L8 + 1 SA + 1 AU AO AT TR CODE High foot 3 434 00 307 40 434 00 308 50 434 00 309 63 434 00 310 80 434 00 311 100 434 00 31 DIMENSIONS AB AH AO AT AU AM E L8 UF SA TR XA Weights (kg) 7 3 11 8 4 50 94 54 14 3.5 3 144 0.180 10 36 15 8 8 4 58 105 6 161 38 36 163 0.50 10 45 15 10 3 3 70 106 77 170 46.5 45 175 0.470 10 50 15 10 3 3 85 11 87 185 56.5 50 190 0.595 1 63 0 1 41 40 105 18 110 10 7 63 15 1.65 14.5 71 5 1 41 40 130 138 130 0 89 75 30 - P11-9-17
Series 453 FEMALE CLEVIS - AP ISO 8140 - RP 10 P CK H9/d10 AV SPHERICAL BEARING ROD END - AP6 ISO 8139 - RP 103 P α : spherical angular compensation: 4 α α KK B max. CM EN h1 CN H9 AX ER max. LE CE KK ER max. LF CH CL DIMENSIONS AV-AX B CE CH CK CL CM CN E EN ER KK LE LF 3 0 6 40 43 10 0 + 0.5 10 + 0.15 10 56 14 14 M10x1.5 0 15 40 3 48 50 1 4 + 0.5 1 + 0.15 1 67 16 16 M1x1.5 4 17 50 8 41 64 64 16 3 + 0.5 16 + 0.15 16 89 1 1 M16x1.5 3 63 8 41 64 64 16 3 + 0.5 16 + 0.15 16 89 1 1 M16x1.5 3 80 33 48 80 77 0 40 + 0.6 0 + 0.15 0 11 5 5 M0x1.5 40 6 100 33 48 80 77 0 40 + 0.6 0 + 0.15 0 11 5 5 M0x1.5 40 6 Female clevis Spherical bearing 3 0.100 0.070 40 0.150 0.10 50 0.330 0.0 Female clevis Spherical bearing 63 0.330 0.0 80 0.670 0.390 100 0.670 0.390 ALIGNMENT COMPENSATOR R AM X min. ZJ + 1 AM KW AM1 4 økk 4 økk T () P () 1 : + stroke () : dimensions on flats W1 () W () DIMENSIONS AM AM1 P() KK KW R T() W1() W() X Radiale compensation Weights (kg) 3 6 1 M10x1.5 6 73 17 30 19 58 0.7 0.10 40 4 6 1 M1x1.5 7 77 19 30 19 59 0.7 0.10 50 3 34 19 M16x1.5 8 106 4 4 30 8 1 0.650 63 3 34 19 M16x1.5 8 106 4 4 30 8 1 0.650 80 40 4 19 M0x1.5 9 1 30 4 30 9 1 0.680 100 40 4 19 M0x1.5 9 1 30 4 30 9 1 0.680 Radial compensation: 0.7 to 1 mm (see table) Spherical angular compensation: 4 Note: The compensator is preset with an axial clearance of 0.05 to 0.1 - Do not reset. P11-9-18
11 Spare parts kit PES CYLINDERS WITH PROFILED BARREL 1 3 3 4 (100) Magnet CYLINDER 3 40 50 63 80 100 Cylinder type CODES (seals: 1 to 4) Equipped for detector 978 0 343 Equipped for detector 978 0 344 Equipped for detector 978 0 345 Equipped for detector 978 0 346 Equipped for detector 978 0 347 Equipped for detector 978 0 59 NOTE: For best results, use grease supplied in each kit. Supplementary tube (11 cm 3 ) available on request, code: 978 0 100 P11-9-19
EUROPE BELGIUM ASCO/JOUCOMATIC BENELUX Lusambostraat 53, Rue de Lusambo 1190 BRUSSEL / BRUXELLES Tel.(3) / 333 0 50 - Fax (3) / 333 0 51 E-mail: ajb@asco.joucomatic.be CZECH REPUBLIC ASCO JOUCOMATIC S.R.O. Udolni 15 - CZ 140 00 - PRAHA 4 Tel. (40) / 61315 411 - Fax (40) / 61315 444 E-mail: asco@ascojoucomatic.cz FRANCE ASCO JOUCOMATIC SA 3, Av. Albert 1er - B.P. 31-9506 RUEIL Cedex Tel.(33) (0) 1 47 14 3 00 - Tx 634 8 - Fax (33) (0) 1 47 08 53 85 www.ascojoucomatic.fr GERMANY ASCO JOUCOMATIC GmbH & Co. Otto-Hahn-Str. 5-7548 ÖLBRONN-DÜRRN Tel.(49) 737 9960 - Fax (49) 737 9961 E-mail: info@ascojoucomatic.de GREAT BRITAIN ASCO JOUCOMATIC Ltd. Pit Hey Place, West Pimbo - SKELMERSDALE - Lancashire WN8 9PG Tel.(44) 1 / 695 71 36 00 - Fax (44) 1/ 695 71 36 33 E-mail: general@ascojoucomatic.co.uk HUNGARY ASCO/JOUCOMATIC (ASCO Kft.) Bogancs u. 1-3 - 1151 BUDAPEST Tel.(36) 1 / 306 41 00 - Fax (36) 1 / 306 09 80 E-mail: office@ascojoucomatic.hu ITALY ASCO JOUCOMATIC SpA Via Zambeletti - ang. Via Ghisallo - 001 BARANZATE di BOLLATE (MI) Tel.(39) 0 / 35 693 1 - Fax (39) 0 / 35 693 300 E-mail: aji@ascojoucomatic.it AMERICAS BRAZIL ASCO/JOUCOMATIC (ASCOVAL ind. e. com. Ltda.) Rod. Pres. Castelo Branco Km 0 - Jd. Sta. Cecilia CEP 06465-300 BARUERI - SAO PAULO Tel.(55) 11 / 4195 5333 - Fax (55) 11 / 4195 3970 E-mail: ascobrbr@ascoval.com.br CANADA ASCO/JOUCOMATIC (ASCOVALVE Inc) Airport Road - PO Box 160 - BRANTFORD, ONTARIO N3T 5M8 Tel.(1) 519 / 758 700 - Fax (1) 519 / 758 5540 E-mail: ascomail@asco.on.ca AFRICA & MIDDLE EAST SOUTH AFRICA ASCO/JOUCOMATIC (ASCOREG) P.O. Box 737-3 Commerce Place Eastgate Ext. 1, Sandton - GAUTENG Tel. (7) 11 / 444 13 - Fax (7) 11 / 444 1 E-mail: ascoreg@mweb.co.za www.ascojoucomatic.com NETHERLANDS ASCO/JOUCOMATIC (ASCO CONTROLS BV) Industrielaan 1-395 BD - SCHERPENZEEL Tel.(31) 33 77 7911 - Fax (31) 33 77 7888 E-mail: info@ascojoucomatic.nl POLAND ASCO JOUCOMATIC Sp. z o.o. Ul. Konstruktorska 11a 0 673 WARSAW Tel.(48) / 54 85 80 - Fax (48) / 54 85 88 E-mail: biuro@ascojoucomatic.pl PORTUGAL ASCO/JOUCOMATIC (FLUIDOCONTROL S.A.) Rua Eng Ferreira Dias, 938 - AZ 4100-46 PORTO Tel.(351) 6 199 870 - Fax (351) 6 176 517 E-mail: geral@fluidocontrol.pt SPAIN ASCO/JOUCOMATIC (FLUIDOCONTROL S.A.) 39700 CASTRO-URDIALES (Cantabria) Tel.(34) 94 87 61 00 - Fax (34) 94 86 33 3 E-mail: fluidocontrol@ajefluido.com SWEDEN ASCO/JOUCOMATIC (ASCO AB) Albanoliden 3-5 - 506 30 BORÅS Tel.(46) 33 / 108 000 - Fax (46) 33 / 108 080 E-mail: asco@asco.se SWITZERLAND ASCO/JOUCOMATIC Switzerland (ASCO CONTROLS AG) Schaftenholzweg 16-557 STUDEN / BIEL-BIENNE Tel.(41) 3 / 374 45 10 - Fax (41) 3 / 374 45 11 E-mail: info@ascojoucomatic.ch TURKEY ASCO/JOUCOMATIC TURKEY Bayar Cd. Gülbahar Sk. - Perdemsaç Plaza N 17/97 81090 KOZYATAGI - ISTANBUL Tel.(90) 16 / 464 07 70 - Fax (90) 16 / 464 07 71 E-mail: ajturkey@superonline.com MEXICO ASCO/JOUCOMATIC (ASCOMATICA S.A. de C.V.) Bosques de Duraznos 65-1003 A Bosques de las Lomas - 11700 MEXICO D.F. Tel.(5)5 / 596 77 41 - Fax (5)5 / 596 77 19 E-mail: cmendoza@asco.com.mx USA ASCO (Valve, Inc) 50 Hanover Road - FLORHAM PARK, NJ 0793 Tel.(1) 973 / 966 000 - Fax (1) 973 / 966 68 E-mail: info-valve@asco.com UNITED ARAB EMIRATES ASCO/JOUCOMATIC MIDEAST PO Box 17034 - Jebel Ali free zone - DUBAI Tel.(971) 4 / 883 44 94 - Fax (971) 4 / 883 44 95 E-mail: ascojoucomatic@emersondubai.com ASIA & OCEANIA HONG KONG ASCO/JOUCOMATIC (ASCO ASIA) Room 3904, Central Plaza, 18 Harbour Road - WANCHAI Tel.(85) 343 8580 - Fax (85) 790 1771 E-mail: ascohk@emrsn.com.hk INDIA ASCO/JOUCOMATIC (ASCO INDIA Ltd.) 147 Karapakkam village - MADRAS 600 096 Tel. (91) 44 450 451 - Fax (91) 44 450 70 E-mail: asco5@sanmargroup.com JAPAN ASCO/JOUCOMATIC (ASCO JAPAN Co. Ltd.) 1-0 Takahata-Cho Nishinomiya - HYOGO 663-80 Tel. (81) 798 65 6361 - Fax (81) 798 63 4443 E-mail: asco@ascojp.co.jp KOREA ASCO/JOUCOMATIC (ASCO ASIA) 6 fl. Chunglim Bldg, 38-30 Samsung-dong Kangnam-Ku - SEOUL 135 090 Tel.(8) / 515 485 - Fax (8) / 540 350 E-mail: asco@ascokorea.co.kr SINGAPORE ASCO/JOUCOMATIC (ASCO ASIA) Blk 4008, Ang Mo Kio Ave.10-04-17/, Techplace1 SINGAPORE 569 65 Tel.(65) 556 11 00 - Fax (65) 556 00 11 E-mail: valvesales@asco.com.sg TAIWAN R.O.C. ASCO/JOUCOMATIC (ASCO ASIA) 5th. fl, N Jen Ai Road - Section 4 - TAIPEI 10650 Tel.(886) / 35 9555 - Fax (886) / 70 6009 E-mail: ascotw@ms17.hinet.net AUSTRALIA ASCO/JOUCOMATIC (ASCOMATION Pty. Ltd.) Unit 1, Allambie Grove Business Park 5 Frenchs Forest Road East - FRENCHS FOREST - N.S.W. 086 Tel.(61) / 9451 7077 - Fax (61) / 9451 994 - E-mail: sales@asco.com.au NEW ZEALAND ASCO/JOUCOMATIC (ASCOMATION Pty. Ltd.) 3 Vega place - Mairangi Bay PO. Box 30 441 - North Harbour - AUCKLAND Tel.(64) 9 / 478 019 - Fax (64) 9 / 478 0193 E-mail: gbrown@asco.com.au ASCO/JOUCOMATIC REPRESENTATIVES (see web) Algeria - Argentina - Austria - Bolivia - Bulgaria - Cameroon - Chile - China - Colombia - Costa Rica - Croatia - Denmark - Ecuador - Egypt - Finland - Greece - Guadeloupe - Guatemala - Honduras - Iceland - Ireland - Israël - Ivory Coast - Luxemburg - Martinique - Morocco - Nicaragua - Norway - Pakistan - Panama - Peru - Porto Rico - Reunion Island and Madagascan Rep. - Romania - Russia - El Salvador - Saudi Arabia - Senegal - Slovakia - Slovenia - Tunisia - Ukraine - Uruguay - Venezuela - F.R. Yugoslavia (all other countries, contact E-mail : export.sales@ascojoucomatic.fr) 4CV.GB-04/03 383 93 78-0000000 Consult our network on: www.ascojoucomatic.com (Contacts header) Local distributor - Distribué par - Ihr Ansprechpartner :