CTENTS MY HOME Video door entry and home video surveillance system General features...................... 34 General rules for installation.............. 36 Wiring diagrams...................... 376 MY HOME - VIDEO DOOR ENTRY AND HOME VIDEO SURVEILLANCE SYSTEM 34
MY HOME - VidEO door ENTrY and HOME VidEO SurVEillaNCE SYSTEM - GENERAL FEATURES System composition The wire video door entry system uses the same SCS technology of all the MY HOME applications. Regardless of system complexity, the functions needed, and the number of video handsets, all the devices are connected using the same wire cable, and are configured univocally. In order to increase the system safety level, it is possible to connect wire indoor and outdoor cameras, the which images will be displayed directly on the video handsets (home video surveillance function). If a higher level of safety is required, it will be possible to associate an IR sensor of the burglar-alarm system to each sensor. In this way, in case of trespassing, both the camera and the video handset will activate automatically. In order to complete a wire video door entry system, in addition to the Outdoor pushbutton panel and the handsets, a few accessory will be needed, connected to the wire. 3 riser ( wires) 4 Electric distribution board or My Home Flatwall Floor shunt System expansion module Entrance panel 34
. ENTrANCE panel: room sends the call to the video handset(s) (available in various look and installation models). 6 room room 3 room 4 The apartment interface enables creating an independent system inside the apartment. In this way, it is possible to install apartment handsets with simultaneous switching on, entrance panels and dedicated cameras. Axolute nighter video station Polyx Memory display Video handset Apartment interface Axolute Eteris Video display 6 5 6. SYSTEM EXpANSI MODuLE: it can be used to increase the performance of the system, for example to increase the distance between the outdoor pushbutton panel and the video handsets. 3. ELECTrIC DISTrIBuTI BOArD Or MY HOME FLATWALL: It enables the user to install DIN devices: SYSTEM POWER SUPPLY: powers the and all the devices. AUDIO/VIDEO NODE: mixes the audio and video signals from external sources (entrance panels, cameras, sound sources...) and retransmits them on the WIRE riser (in alternative the audio/video matrix can also be used). 4. FLOOr SHuNT: used for star-connecting 4 apartments, hence saving a lot of cable. In addition, it lets you reach the maximum extension of the system 5. ApArTMENT INTErFACE: used for isolating the apartment from the riser. In this way, inside the apartment it will be possible to install an independent system with the corresponding MY HOME applications. MY HOME - VIDEO DOOR ENTRY AND HOME VIDEO SURVEILLANCE SYSTEM 6. VIDEO HANDSETS: audio-video terminal which enables you to receive calls and to see who is calling. Using the icons of the OSD menu it is possible to manage and control MY HOME applications. (Available in various look and installation models) 343
MY HOME - VidEO door ENTrY and HOME VidEO SurVEillaNCE SYSTEM - GENERAL FEATURES Simple installation The wire system can be used to create any type of systems, both for the villa and the apartment complex. Furthest handset Entrance panel 600 metres THE SYSTEM MAY INCLuDE: 3900 Apartments 3900 Apartment video entrance panel 5 Handsets for apartment 39 risers with indepedent sound mode 96 Video entrance panel 344
Devices ENTrANCE panel Outdoor video pushbutton panel with colour camera. It can be used wall entrance panel outdoor Axolute entrance panel to call the video handsets and to activate the associated door lock. Available in various look and installation models. Axolute nighter & whice Video Station Flush mounted entrance panel Polyx memory display Axolute video display VIDEO HANDSETS Video handsets for the audio and video reception of entrance panel calls. Their icons allow the user to manage the video door entry system, and the MY HOME functions. Available in various look and installation models. MY HOME - VIDEO DOOR ENTRY AND HOME VIDEO SURVEILLANCE SYSTEM INDOOr CAMErAS WIRE indoor colour camera that can Cameras with front cover plates be connected directly to the system SCS. Microphone for the room monitoring function. Available in the AXOLUTE, LIVING, LIGHT and LIGHT TECH versions. To be completed with the corresponding front cover plates. 345
MY HOME - VidEO door ENTrY and HOME VidEO SurVEillaNCE SYSTEM - GENERAL FEATURES Devices Apartment interface SYSTEM EXpANSI MODuLE Used to increase the number of video handsets connected to the system and to achieve maximum installation distance. System expansion module outdoor camera ApArTMENT INTErFACE To create a dedicated system inside the Apartment, separate from the apartment complex riser. In the apartment, it will therefore be possible to create a video door entry system with dedicated entrance panels and cameras, integrated with the other MY HOME systems. OuTDOOr CAMErA WIRE outdoor colour camera with 6 mm fixed optics to be connected directly to the SCS. Protection index: IP65 ACTuATOrS Used for the control of electric locks, or the management of generic loads (e.g. staircase lights, call repetition, etc.). door lock actuator FLOOr SHuNT The floor shunt can be used to create star wiring systems. Its use is compulsory for installation in simultaneous switching on systems. Floor shunt Actuator for generic loads 346
Audio/video node MuLTICHANNEL MATrIX It functions is that of an advanced audio/video mixing device. It has 4 sound source inputs and 4 inputs for video door entry system/ cameras, which can be distributed simultaneously. To be used in alternative to the audio/video node, in MY HOME systems with integrated video door entry system and sound system. MuLTIMEDIA TOuCH SCrEEN 0" Touch Screen display for the management and the control of MY HOME applications. It can be used to answer video door entry system calls, and to display images from the cameras connected to the system. It manages audio, video, and WEB multimedia contents through the USB connection. It has an SD card slot, and LAN connection. To be completed with the surround plate. Video adapter Multimedia Touch Screen AuDIO/VIDEO NODE AND VIDEO ADApTEr They perform the function of audio/ video mixers, for the connection to the system of entrance panels and video handsets. The audio/video node can be used to connect up to 4 entrance panels / cameras and up to 4 risers. The video adapter on the other hand can be used to connect entrance panels and riser (or entrance panel and risers). during presetting, the inclusion of the audio/video node is recommended, to allow for future system expansions. Multichannel matrix 347 MY HOME - VIDEO DOOR ENTRY AND HOME VIDEO SURVEILLANCE SYSTEM
MY HOME - VidEO door ENTrY and HOME VidEO SurVEillaNCE SYSTEM - GENERAL FEATURES Example - Villa E-FAMILY VIDEO DOOr-ENTrY SYSTEM WITH INTErCOM BETWEEN VIDEO HANDSETS nighter Video Station whice Video Station Audio/video node Power supply Entrance panel 348
LIVInG room room reception room = T = S = 9 on 34300 S 34930 34930 34930 O U T I N = 5 = = OUT OUT O UT3 OUT 4 I N I N I N 3 I N 4 = 4 = 3 F44 346000 30 Vac 3493 3493 room KITCHEn MY HOME - VIDEO DOOR ENTRY AND HOME VIDEO SURVEILLANCE SYSTEM ITEM DESCRIPTI QUANTITY 34300 F44 346000 34930 3493 S Entrance panel Audio/video node Power supply Nighter Video Station Whice Video Station Electrical door lock 3 349
MY HOME - VidEO door ENTrY and HOME VidEO SurVEillaNCE SYSTEM - GENERAL FEATURES Example - Villa E-FAMILY VIDEO DOOr-ENTrY SYSTEM WITH OuTDOOr CAMErAS nighter Video Station whice Video Station Polyx Memory display Audio/video node Power supply outdoor camera 350 Entrance panel
LInVInG room room reception room on = = T = S = 9 = Z = A = PL = 3499 34463 34930 34930 = = = 5 S O U T I N OUT OUT O UT3 OUT 4 I N I N I N 3 I N 4 = 4 = 3 3493 3493 F44 346000 30 V 39670 39670 = Z = A = PL = room KITCHEn MY HOME - VIDEO DOOR ENTRY AND HOME VIDEO SURVEILLANCE SYSTEM ITEM DESCRIPTI QUANTITY 3499 39670 F44 346000 34930 3493 34463 S Entrance panel Outdoor camera Audio/video node Power supply Video Station Nighter Whice Video Station Polyx Memory Display Electrical door lock Max. 5 handsets Max. 00 metres between the entrance panel and the last handset S = Electric door lock 8 V 4 A impulsive 50 ma holding current note : we recommend that the video handsets are configured using the software supplied with the product nota : The answering machine function is available only using the 34463 video handset, and can only be activated on video handset (the one configured with n=) 35
MY HOME - VidEO door ENTrY and HOME VidEO SurVEillaNCE SYSTEM - GENERAL FEATURES Example 3 - Apartment ApArTMENT WITH DEDICATED ENTrANCE panel AND private CAMErAS Indoor camera outdoor camera Axolute Eteris Video display Apartment interface Audio/video node Power supply 35 Polyx Memory display
on 34463 = 5 P = APArTMEnT EXTEnSIon BUILdInG riser on = 5 M = 3 OUT IN 346850 C OK 349340 34463 3499 = 4 P = = 3 P = = T = S = 9 S F44 OUT OUT O UT3 OUT 4 O U T I N I N I N I N 3 I N 4 30 Vac 34463 34463 346000 3966 39670 on = P = = P = = 3 Z = A = PL = = Z = A = PL = MY HOME - VIDEO DOOR ENTRY AND HOME VIDEO SURVEILLANCE SYSTEM ITEM DESCRIPTI QUANTITY BUILdInG riser 3499 39670 3966 346000 F44 346850 34463 349340 S L000 Entrance panel Outdoor camera Axolute indoor camera Power supply Audio/video node Apartment interface Polyx memory display Eteris Video Display Electrical door lock 4 Max 5 video handsets, apartment EP and apartment cameras note : we recommend that the video handsets are configured using the software supplied with the product note : Configure the entrance panels and the apartment cameras starting from (P=) note 3: The audio/video answering machine can only be activated on one 34463 video handset (the one configured with n=-) 353
MY HOME - VidEO door ENTrY and HOME VidEO SurVEillaNCE SYSTEM - GENERAL FEATURES Example 4 - Complexes of small houses MuLTI-FAMILY SYSTEM WITH SINGLE INDEpENDENT DWELLINGS AND AT LEAST E COMM ACCESS point Entrance panel Apartment interface Audio/video node Power supply 354
TMP PL RC C NC NO/S+ S Inside of the apartment Inside of the apartment see previous diagram see previous diagram SMALL HoUSE 35 SMALL HoUSE 99 OUT IN OUT IN 346850 346850 346850 n = 3 = 5 M = 3 n = 9 = 9 M = 3 Inside of the apartment Inside of the apartment see previous diagram SMALL HoUSE see previous diagram SMALL HoUSE 6 = M = 3 max. 50 m n = = 6 M = 3 OUT IN OUT IN 346850 F44 346000 34660 30 Vac = P = S = The EP must be configured and programmed using the software supplied with the product on SCS S = P = T = JMP JMP MY HOME - VIDEO DOOR ENTRY AND HOME VIDEO SURVEILLANCE SYSTEM ITEM DESCRIPTI QUANTITY 34940 34940 3393 33933 F44 346000 346850 S 34660 Axolute entrance panel Front cover plate Flush mounted box Audio/video node Power supply Apartment interface Electrical door lock Door lock actuator - 99 Max 99 apartment interfaces and apartment complex entrance panel Max 50 metres between entrance panel and audio/video node 355
MY HOME - VidEO door ENTrY and HOME VidEO SurVEillaNCE SYSTEM - GENERAL FEATURES System functions call communication call Apartment Apartment The handset rings and the monitor switches on The conversation cannot be heard All the handsets, on the same call, ring and switch on the monitor. THE CALL Pressing the call pushbutton on the entrance panel, the system generates a signal that is only recognised by the video handsets the call is addressed to (the call will have to be answered within 30 seconds from the moment the pushbutton is pressed). Each VIDEO handset is configured in a unique specific way. When the call is received, the video handset rings and the monitor switches on. Press the pushbutton to establish the communication (maximum duration of the communication is minute) with the entrance panel. Press again to stop the communication and switch the monitor off. CVErSATI SECrECY During the conversation between the entrance panel and the video handsets, all external panels and handsets that are not involved in the conversation are temporarily excluded in order to guarantee the privacy of video door entry conversations. When calling from an entrance panel that is temporarily excluded, a time-out tone will be heard, to indicate that the extension line is momentarily busy. SIMuLTANEOuS SWITCHING With video handsets, simultaneous switching on of the monitor is also possible: upon arrival of the call, all handsets ring and the monitors of all video handsets switch on. When the call is answered, only the monitor of the video handset communicating with the entrance panel will remain on. In order to set this function, all the video handsets but one must be powered locally using an additional power supply, item 34600. 356
call CLAK Pressing the door lock key will open the gate associated with the handset. DOOr LOCK pushbutt The video handsets are fitted with a door lock pushbutton. Pressing this pushbutton will open of one of the door locks of the system. With the system at rest, the pressure of the pushbutton will cause the opening of the door lock of the entrance panel associated with the handset during the P configuration of the handset itself. On the other hand, if the pushbutton is pressed during the call, the door lock associated to the entrance panel making the call will be opened. The staircase light function will switch on the system lights connected to a special actuator THE STAIrCASE LIGHT FuNCTI The video handsets are equipped with an icons menu. This function activates a relay for the timed switching on of lights and the opening of the gate. The function can be performed by installing the actuator item 34600, appropriately configured. Each time the self-switching on key is pressed the images displayed change. SELF-SWITCHING pushbutt By pressing the self-switching on pushbutton while the videohandset is at rest, a connection will be established with the entrance panel associated with the handset during the P configuration of the handset itself. Pressing repeatedly on the selfswitching on pushbutton, will scroll through the various entrance panels and the cameras connected to the system. MY HOME - VIDEO DOOR ENTRY AND HOME VIDEO SURVEILLANCE SYSTEM 357
MY HOME - VidEO door ENTrY and HOME VidEO SurVEillaNCE SYSTEM - GENERAL FEATURES System functions Apartment call INTERCOM call Item 346850 apartment interface enables the InTErCoM function between the devices within the one apartment and the various apartments Master Slave Apartment when a call is received, the MASTEr comes on, while the SLAVE will only ring. APArTMEnT MASTEr-SLAVE FuNCTI INTErCOM For multi-family installations the The system offers an intercom MASTER-SLAVE function is available: function, with up to 3 minutes APArTMEnT when the call is received, all the communications between apartment handsets ring, but only videohandsets: the monitor of the video handset From different apartments configured as master comes on. Within the same apartment When the auto-switching on key of If the apartment has an apartment a SLAVE is pressed, the monitor of interface - item 346850 - or is the MASTER handset turns off, while a one- family apartment, each the monitor of the SLAVE itself turns videohandset of the apartment can on (without necessarily establishing be called individually. The INTERCOM communication with the entrance connection can be established at panel). If the connection key the same time as other external of a SLAVE is pressed, the MASTER connections. The INTERCOM monitor turns off and communication connection can be simultaneous to with the audio-video entrance panel other connections external to the is established. apartment. If the apartment does not have an apartment interface - item 346850 - any apartment handset can call all other apartment handsets. The INTERCOM connection will not occur at the same time as external connections. Any call received by an EP, even to any other apartment, will 358 terminate the INTERCOM connection.
we are currently out... MESSAGGIO MESSAGGIO MESSAGGIO 3 MESSAGGIO MESSAGGIO MESSAGGIO 3 MESSAGGIO MESSAGGIO MESSAGGIO 3 MESSAGGIO MESSAGGIO MESSAGGIO 3 MESSAGGE MESSAGGE MESSAGGE 3 Playback of sounds and images recorded by the answering machine VIDEO DOOr ENTrY SYSTEM ANSWErING MACHINE FuNCTI Function available only using the POLYX MEMORY DISPLAY video handset, item 34463. It is possible to record voice and images of a call from an entrance panel. It is also possible to record an audio message to play back on the entrance panel following an unanswered call. The video door entry system message can be recorded in ways: STILLS: the message includes a picture of the visitor and the recorded audio message (60 messages max). VIDEOS: the message includes a MY HOME - VIDEO DOOR ENTRY AND HOME VIDEO SURVEILLANCE SYSTEM Answering machine active video feed (duration 6 seconds) and the recorded audio message (8 messages max). Each message will be given a progressive number, which will be displayed on the video handset, together with the date and time information. 359
MY HOME - VidEO door ENTrY and HOME VidEO SurVEillaNCE SYSTEM - GENERAL FEATURES System functions Ir detector and associated cameras dinner is served! on UP pager FuNCTI IN SYSTEMS INTEGrATED WITH SOuND SYSTEM By pressing the conversation pushbutton on the video handsets, it is possible to broadcast a message through all the loudspeakers of the sound system. The involved video handsets must be powered locally. From the video handset menu it is possible to control and display the functions of the sound system through the icons of the menu itself. note: function possible by configuring the video handsets using the software supplied with the product. SCENArIO CTrOL FuNCTI IN SYSTEMS INTEGrATED WITH AuTOMATI SYSTEM From the video handsets, it is possible to recall the scenarios saved in the F40 scenarios. note: function possible by configuring the video handsets using the software supplied with the product. SWITCHING CAMErA FuNCTI IN SYSTEMS INTEGrATED WITH THE BurGLAr ALArM SYSTEM It is possible to associate a zone of the burglar alarm to the cameras. When an alarm situation is detected, the images recorded by the camera are displayed on the video handset. Using the appropriate icons of the menu of the video handset, it is possible to monitor the status of the burglar-alarm system: for example, the status of the burglar-alarm (armed/disarmed), active zones, alarms occurred. note: function possible by configuring the video handsets using the software supplied with the product. 360
CUCINA 0.5 C off KITCHEN A + +.5 (+) 8.5 C SupErVISI FuNCTI IN SYSTEMS INTEGrATED WITH THE TEMpErATurE CTrOL SYSTEM From the video handset menu, it is possible to display the status of the temperature control system. Using the appropriate icons it is possible, for example, to change the temperature parameters, and display the status of the probes. note: function possible by configuring the video handsets using the software supplied with the product. 0.5 C off A + +.5 (+) 8.5 C MY HOME - VIDEO DOOR ENTRY AND HOME VIDEO SURVEILLANCE SYSTEM 36
MY HOME - Video door entry and home video surveillance system - General rules for installation System composition The system is classed as SELV (Safety Extra Low Voltage) due to the fact that it is powered by non grounded safety double insulation independent power supplies with a max. voltage of 5 Vac (effective) or 60Vdc noninverted voltage. In addition, all BTicino devices are double insulated. The conformity to SELV classification is only guaranteed only subject to FULL COMPLIANCE with current installation regulations and with the GENERAL RULES FOR INSTALLATI relating to each single device and cable, making up the installation. BASIC ELEMENTS OF THE VIDEO SYSTEM In order to install a system it is necessary to purchase, in addition to the entrance panel and the handset, also the 346830 video adapter, or the F44 audio/video node, and the 34684 floor shunt with the function of distributing the video signal. Video adapter The video adapter is used to connect Video adapter entrance panels and handsets to a wire video system A maximum of 3 connections are allowed on the video adapter. TK PI Power supply Video handset PS Video adapter Video entrance panel Entrance panels Handsets TK PI PS Power supply 346000 A maximum of 3 connections are allowed on the video adapter. (*) Entrance panels Handsets Entrance panel Handsets TK PI TK PI PS PS Connection of entrance panels and a riser for the handsets Connection of entrance panel and risers for the handsets (*) If either an interface is connected to the entrance panel, only one connection on the TK terminal of the video adapter is possible. 36
AuDIO/VIDEO NODE Or VIDEO MATrIX The F44 audio/video node and the F44M video matrix must be used in alternative to the video adapter when more than entrance panels must be installed in the system, or when more than risers are needed. The use of the audio/video node or the video matrix is however recommended, to allow for future my Home integrations, system expansions, and/or addition of cameras. Allow for one output of the audio/ video node, or the video matrix, for each video door entry system video handset with table-top installation. FLOOr SHuNT When creating video systems, the use of the floor shunt, item 34684 is recommended. This will provide important savings on the cable to be used. This is particularly suitable for multi-family systems, when more than one living unit on the same floor or in multi-family systems, where max. distance between the entrance panel and all handsets is needed. The Floor shunt enables star connection of up to 4 apartments with a max. of 3 handsets for Apartment (max. handset per output, if set in simultaneous switching on). One output of the audio/video node should be dedicated to each tablemounted video handset installed. AUdIo/VIdEo node FLoor SHUnT Video entrance panel Audio/video node riser To the handsets To the entrance panels/cameras Apartment Power supply For each output: max. 3 video handsets or bells in the same apartment max. video handset in simultaneous switching on max. table-mounted video handset Apartment Apartment 3 ART. 34684 wire riser Power supply Apartment 4 Video handset MY HOME - VIDEO DOOR ENTRY AND HOME VIDEO SURVEILLANCE SYSTEM 363
MY HOME - VidEO door ENTrY and HOME VidEO SurVEillaNCE SYSTEM - GENERAL RULES FOR INSTALLATI System composition SYSTEM EXpANSI MODuLE 34685 IN MOD = 0 (SYSTEM EXpANSI MODE) To be used for system expansion, in order to: Regenerate the video signal and have a further 00 m available after the interface (using the 336904 cable) Increase the number of devices connected to the Use a max. of 3 modules, configured using the MOD = 0 in cascade. As far as the system composition, distances and topology are concerned, within the system section, the system expansion module item 34685 must be considered as a handset. On the other side, within the system section it should be considered as an entrance panel. Mod = 0 Entrance panel System section System section F44 346000 34685 F44 346000 OUT IN 00 m 00 m 34685 34685 34685 34685 max. item 34685 with Mod = 0 for each output 346000 OUT OUT OUT OUT IN IN IN IN Entrance panel F44 346000 F44 The In clamp of the system expansion modules configured with Mod = 0 must be connected to a dedicated output of the F44 audio/video node or the 34684 floor shunt (as a handset with local power supply). 364
SYSTEM EXpANSI MODuLE ITEM 34685 IN MOD = 5 (INDEpENDENT riser MODE) This is used in buildings to have risers with riser entrance panels and independent audio and video functions. Common system section Entrance panel riser system section (with independent audio) riser riser OUT IN F44 346000 F44 346000 riser entrance panel 34685 34685 riser system section (with independent audio) OUT IN Mod = 5 riser entrance panel MY HOME - VIDEO DOOR ENTRY AND HOME VIDEO SURVEILLANCE SYSTEM F44 346000 In the common system section, for the purpose of system composition, distances and layout, the system expansion modules must be treated as a handsets. on the other hand, in the riser system sections they must be treated as entrance panels. The building entrance panel must be made with alphanumeric or numeric call module 365
MY HOME - VidEO door ENTrY and HOME VidEO SurVEillaNCE SYSTEM - GENERAL RULES FOR INSTALLATI System composition ApArTMENT INTErFACE ITEM 346850 This is used to have an apartment system independent from the building. In this way, the apartment system can have private cameras and entrance panels and can be integrated with all the MY HOME applications. As far as the system composition, distances and topology are concerned, within the building system, the interface item 346850 must be treated as a handset. On the other side, within the apartment system, it should be treated as an entrance panel configured with P = 0. Apartment block system section For the completion of the system, any type of cable can be used (including existing cables). Maximum performance and distances are achieved using the OUT IN 346850 F44 Apartment system section 346000 Handset 336904 cable. Entrance panel F44 346000 Apartment entrance panel Apartment camera 366
Configuration To configure means to program the system. This occurs assigning an identification and operational mode number to the devices. This operation is made inserting in the appropriate seats some configurators (numbered from 0 to 9), using a clamp provided with the power supply or contained in the case of the configurators or using the configuration software (recommended). A seat is left empty corresponds to the configuration of a zero. In the system exist two different numerations to identify respectively the entrance panels (EP) and the handsets. The numeration of the EP (0-96) is generally identified by P, while the address of the handsets (0-99) is identified by N. On the EP, in addition to the P address it is necessary to configure also the N address relating to the handset from which we would start to call. On the handsets in addition to the N address, it is necessary to configure in P the EP associated to the same handset, or the entrance panel on which the door lock and autoswitching controls work when the handset is switched. = S = The configurators can be purchased in a case or individually Example of configured system and its operation door lock and auto-switching on controls in pause from apartment 3 4 5 6 7 8 9 0 Apartment Apartment 5 Call apartment 350K 350/ 350/ 350/3 350/4 350/5 350/6 350/7 350/8 350/9 350/0 350/SLA = I 0-9 Call apartment 5 door lock and auto-switching on controls in pause from apartment 5 S L A n = = 5 P = = S = MY HOME - VIDEO DOOR ENTRY AND HOME VIDEO SURVEILLANCE SYSTEM Should occur the need to modify the configuration of a device, it is necessary, in addition to change the configurators, take off the power supply to the whole system, wait minute, and then provide voltage again. For each device exist also particular configurations which will be detailed in the product technical sheet. 367
34685 34685 34685 34685 34685 34685 MY HOME - VidEO door ENTrY and HOME VidEO SurVEillaNCE SYSTEM - GENERAL RULES FOR INSTALLATI Configuration SYSTEM EXpANSI MODuLE ITEM 34685 The system expansion module can be configured in different ways: (the addresses in M with MOD = 0 and MOD = 5 do not conflict with each other) MOD = 0 for system expansion M = specific progressive number for interface 34685 Mod = 0 M = Video handset Entrance panel Video handset Mod = 0 M = 34685 Mod = 0 M = Mod = 0 M = Mod = 0 M = 3 Mod = 0 M = 4 34685 34685 34685 34685 F44 Entrance panel 368
34685 346850 34685 34685 346850 MOD = 5 for independent audio risers M = specific progressive number indicating the riser number Common entrance panel For the common entrance panel, the handsets have address M (riser number) x 00 + n (handset for the riser). Es. Handset n = 0 of the riser for the common EP = x 00 + 0 = 0 ApArTMENT INTErFACE 346850 IndEPEndEnT wire riser The apartment interface is configured as a normal handset. The interface must be configured in a specific unique way. No other handset can be configured in N using the same address, in the same system or on the same riser with independent audio. The factory device is configured with M = 3. Mod = 5 M = 34685 34685 34685 Correct configuration INT EXT IndEPEndEnT wire riser n = 7 n = 6 Mod = 5 M = SYSTEM wrong configuration wire 346850 wire 346850 IndEPEndEnT wire riser INT EXT Mod = 5 M = 39 n = 5 n = 5 n = 6 n = 5 SYSTEM MY HOME - VIDEO DOOR ENTRY AND HOME VIDEO SURVEILLANCE SYSTEM 369
MY HOME - Video door entry and home video surveillance system - GENERAL RULES FOR INSTALLATI The wiring SYSTEM WIRING The systems can also be wired in modes: in-out wiring STAR wiring with floor shunt 34684 (recommended). In-out wiring In-out wiring is connected directly on the terminal of the appliances which are connected to the system. Each riser must be terminated by positioning the micro switch of the last handset to. In-out wiring is particularly indicated for one and two-family systems and for vertical or horizontal multi-family systems (with the homes in rows). In-out wiring STAR wiring The star wiring is made connecting the individual apartment to an output of the floor distribution block Item 34684. Each line must be terminated by positioning the micro switch of the last appliance to. STAR wiring is particularly suitable for multi-family systems, when more than one living unit on the same floor or in multi-family systems, where max. distance between the entrance panel and all handsets is needed. On each output of the shunt it will be possible to connect up to 3 handsets maximum. An output of the floor distribution block must be dedicated to each handset with simultaneous switching on or table-top base installation. STAR wiring Apartment n Handsets Apartment Apartment 5 Apartment Apartment 3 Apartment Apartment 3 Apartment 4 Apartment 6 Apartment 7 Apartment 8 Apartment 4 wire 34684 34684 370 wire
COMBINED WIrING Both wiring methods described on Apartment n previously can be used together, for the realization of more articulated systems. The combined wiring (IN-OUT and Star) allows to execute wiring systems in order to satisfy the greatest quantity of requests. Floor distribution blocks outputs can be used to connect a single device or to generate an apartment line (on which max. 3 devices can be connected, without using the apartment interface item 346850). To the Bus handset can be connected in IN-OUT floor distribution blocks or handsets. The assignation of the handsets to the apartments occurs through configuration (for further information see technical sheets for the individual devices). on on Apartment 3 Apartment on Apartment on 34684 on Entrance panel Floor shunt 00 m MY HOME - VIDEO DOOR ENTRY AND HOME VIDEO SURVEILLANCE SYSTEM Video entrance panel 37
OF F OF F OF F OF F 346850 346850 34685 34685 INT EXT OF F OF F 346850 34685 MY HOME - VidEO door ENTrY and HOME VidEO SurVEillaNCE SYSTEM - GENERAL RULES FOR INSTALLATI Installation of entrance panels, handsets and interfaces INT EXT INT 60 65 cm EXT 60 65 cm NO HEIGHT OF THE HANDSET When installing the handsets, including standard or video handsets, it is recommended that the devices are positioned at a height of 60 65 cm (top edge). note: recommended installation heights, unless otherwise required by local regulations. INTErFACES ITEM 346850 AND 34685 The interfaces item 346850 (apartment interface) and item 34685 (system expansion module) cannot be installed in a manhole. For their installation, a sealed electric cabin with DIN rail must be used (DIN switchboard). HEIGHT OF THE ENTrANCE panel When installing the Entrance panel, it is recommended that the pushbutton panel is installed at a height of 60 65 cm (top edge). The camera must not be installed in front of light sources, or in places where the subject being filmed is in the shadow. If this condition cannot be respected, the picture will not have much contrast in the darker areas. This is because the brightness is selfregulated on the lighter part of the picture. To solve these problems change the camera installation height, normally 60 65 cm, to a height of 80 cm and direct the lens downwards to improve the quality of the shots. In scarcely lit areas, the installation of an additional light source is recommended. 37
346850 346850 34685 34685 System performance The following information provides general parameters on the maximum distances that can be achieved, and the features of the cables to be used. The type of system considered is a single family system or system below an apartment interface. WARNING: For installation solutions or types other than those shown, the distances and the current absorptions can be calculated using the You Diagram software (which can be downloaded free of charge from the website www.professionisti.bticino.it technical service software and diagrams). Also refer to the specific technical documentation ( WIRE system Technical Guide). LInE A* LInE C* LInE B * Furthest video handset Entrance panel 346000 346830 TK PS PI o INT EXT EXT 346850 34685 346000 Mod = 0 e Mod = 5 F44 346850 34685 Mod = 0 INT e Mod = 5 MAXIMUM DISTANCE LINE A ENTRANCE PANEL - FURTHEST HANDSET Cable section mm normal cables > 0. mm or L4669 336904 twisted telephone pair 0.8 mm one pair of the multi-pair data cable, item C988U/5E 5 HANDSETS in/out 50 m 00 m 40 m 40 m 5 one-fam HANDSETS/OUTDOOR EP 50 m 00 m 00 m 70 m 5 one-fam HANDSETS/EP with local power supply 50 m 00 m 40 m 70 m MAXIMUM DISTANCE LINE C POWER SUPPLY FURTHEST HANDSET Cable section mm normal cables > 0. mm or L4669 336904 twisted telephone pair 0.8 mm one pair of the multi-pair data cable, item C988U/5E 5 HANDSETS in/out 50 m 0 m 70 m 50 m 5 HANDSETS (with shunts) 50 m 0 m 70 m 50 m MAXIMUM DISTANCE LINE B ENTRANCE PANEL POWER SUPPLY Cable section mm normal cables > 0. mm or L4669 336904 twisted telephone pair 0.8 mm one pair of the multi-pair data cable, item C988U/5E pushbuttons 50 m 00 m 5 m 90 m OUTDOOR EP 0 m 50 m 30 m 0 m Entrance panel with local power supply 50 m 00 m 40 m 0 MAXIMUM DISTANCE LINE D ENTRANCE PANEL DOOR LOCK Cable section mm 0.8 BTicino SCS cable - item L4669 BTicino SCS cable - item 336904 MY HOME - VIDEO DOOR ENTRY AND HOME VIDEO SURVEILLANCE SYSTEM S+ S- clamps 30 m 30 m 50 m 00 m (*) Max. variable distance. note: in systems with apartment interfaces only (in/out connection) the distance of LInE d* door lock LInE C to be taken into account is 00 m (with BTicino cable 336904) 373
MY HOME - VidEO door ENTrY and HOME VidEO SurVEillaNCE SYSTEM - GENERAL RULES FOR INSTALLATI System performance SYSTEM WITH ApArTMENT INTErFACE AND SYSTEM EXpANSI MODuLE Up to 3 interfaces, items 346850 Audio/video connection between the entrance panel and the video handset (3 passages maximum) = ok and 34685 may be installed in cascade. Cascade interfaces are those crossed by an audio/video connection (Entrance panel HANDSET) or (HANDSET HANDSET, e.g. INTERCOM). Only of these interfaces (selected by the user) retransmit the signal for 00 metres. Video entrance panel 34685 max. 00 m 34685 The maximum distance between max. 00 m EP and the furthest handset is 600 metres. Each LINE (EP INTERFACE), (INTERFACE INTERFACE) and 34685 34685 (INTERFACE H) must be 00 metres maximum (with BTicino cable max. 00 m 336904). The IN end cap of the system expansion module configured with M=0 MUST be wired and considered as a H with local power supply. max. 00 m It must also be connected to an output of the Audio/video node F44, or the Floor shunt 34684. 346850 INT EXT 346850 374
CNECTI OF 6 AuDIO /VIDEO ENTrANCE panels Or CAMErAS Video door entry system/apartment interface risers F44 346000 OUT OUT O UT3 OUT 4 O U T I N I N I N I N3 I N4 OUT OUT O UT3 OUT 4 OUT OUT O UT3 OUT 4 OUT OUT O UT3 OUT 4 OUT OUT O UT3 OUT 4 O U T O U T O U T O U T I N I N I N I N I N I N I N3 I N4 I N I N I N3 I N4 I N I N I N3 I N4 I N I N I N3 I N4 3499 3499 3499 3499 4 entrance panels or cameras 4 entrance panels or cameras 4 entrance panels or cameras 4 entrance panels or cameras F44 F44 F44 F44 MY HOME - VIDEO DOOR ENTRY AND HOME VIDEO SURVEILLANCE SYSTEM 375
MY HOME - VidEO door ENTrY and HOME VidEO SurVEillaNCE SYSTEM - WIRING DIAGRAMS One-family system with EP and 5 intercommunicating video handsets e device 3 = 3 device = device = 34463 34463 34463 on c device 5 device 4 34463 34463 = 5 = 4 warning Configure the handsets starting from n = Configure and insert the Jumpers with the system SwITCHEd. Also every time the configuration is modified the power supply to the system must be switched off and on again, waiting about minute. The intercom function is operating even with a lack of entrance panel connection. we recommend that the video handsets are configured using the software supplied with the product. A Use of the actuator is necessary for the staircase light service or generic actuations. B For the Entrance Panel, all the pushbutton panels of the wire range can be used c Move the micro switch of the last video or audio handset at the end of the line to the on position d Fit a 9 configurator to be inserted in S on the speaker module for the general call; do not insert any configurator in n. e The audio video answering machine can only be used on video handset (the one configured with n=) Electric distribution board or My Home Flatwall PL S+ S- OUT OUT O UT3 OUT 4 F44 346000 34600 PS S EP O U T I N I N I N I N3 I N4 A 30 Vac 5 6 7 8 3 4 NC C NO 34300 B 30 Vac L = = T = S = 9 d ITEM DESCRIPTI 34300 34463 34600 346000 F44 L EP PS S Linea 000 Metal EP Polyx Memory Display video handset Staircase light actuator (optional) Power supply Audio/video node Staircase light Entrance panel Door lock release pushbutton (optional) Electric door lock 8V 4A impulsive 50mA holding current 376
Two-family systems with EP, 3 handsets per home and intercom between apartments HoME = = = c 34463 34463 34463 EP PS PL S+ S- 34300 = = T = S = on SLAVE SLAVE MASTEr B S A O U T I N HoME OUT OUT O UT3 OUT 4 I N I N I N3 I N4 = = = 34463 34463 34463 Electric distribution board or My Home Flatwall F44 346000 30 Vac on SLAVE SLAVE MASTEr A c warning Configure and insert the Jumpers with the system SwITCHEd. Also every time the configuration is modified the power supply to the system must be switched off and on again, waiting about minute. It is possible to install a maximum of 3 video handsets for apartment. we recommend that the video handsets are configured using the software supplied with the product Configure Master and Slave devices using the software when a call is received, the MASTEr rings and switches on, while the SLAVE will only ring. If the call is answered from a SLAVE unit, the master unit switches off again, while the monitor of the SLAVE from where the call is answered comes on." A Move the micro switch at the back of the last video or audio handset at the end of the line to the on position B For the Entrance Panel, all the pushbutton panels of the wire range can be used. c The audio video answering machine can only be used on video handset (the MASTEr video handset) MY HOME - VIDEO DOOR ENTRY AND HOME VIDEO SURVEILLANCE SYSTEM ITEM 34300 34463 346000 F44 EP PS S DESCRIPTI Two-family Linea 000 Metal entrance panel Polyx Memory Display video handset Power supply Audio/video node Entrance panel (main) Door lock release pushbutton (optional) Electric door lock 8V 4A impulsive 50mA holding current 377
MY HOME - VidEO door ENTrY and HOME VidEO SurVEillaNCE SYSTEM - WIRING DIAGRAMS One-family system with EP and outdoor cameras = 3493 3493 device device PI (5 handsets max.) warning Configure and insert the Jumpers with the system SwITCHEd. Also every time the configuration is modified the power supply to the system must be switched off and on again, waiting about minute. we recommend that the video handsets are configured using the software supplied with the product. End with the micro switch of the last line/riser handset in the on position. A For the Entrance Panel, all the pushbutton panels of the wire range can be used. = B Fit a 9 configurator to be inserted in S on the Entrance panel to make a general call. Electric distribution board or My Home Flatwall F44 346000 OUT OUT O UT3 OUT 4 O U T I N I N I N I N3 I N4 30 Vac EP A EP A 39670 39670 Cam. Cam. PL S+ S- PL S+ S- PS = = T = S = 9 B S PS 3499 3499 S = = T = S = 9 B = Z = A = PL = = 3 Z = A = PL = 378 ITEM 3499 3493 39670 346000 F44 PE-PE PS-PS S-S Cam.-Cam. DESCRIPTI Linea 000 Metal entrance panel Whice Axolute Video Station wire outdoor camera Power supply Audio/video node Entrance panel Door lock release pushbutton (optional) Electric door lock 8V 4A impulsive 50mA holding current wire outdoor camera
PRI 34600 PRI: 0 40 V~ 75 65 ma 47/63 Hz SCS: 7 Vdc 600 ma PRI 34600 PRI: 0 40 V~ 75 65 ma 47/63 Hz SCS: 7 Vdc 600 ma PRI 34600 PRI: 0 40 V~ 75 65 ma 47/63 Hz SCS: 7 Vdc 600 ma - - - PRI 34600 PRI: 0 40 V~ 75 65 ma 47/63 Hz SCS: 7 Vdc 600 ma PRI 34600 PRI: 0 40 V~ 75 65 ma 47/63 Hz SCS: 7 Vdc 600 ma - - One-family system with 5 video handsets in simultaneous switching on O U T I N OUT OUT O UT3 OUT 4 I N I N I N3 I N4 30 Vac 30 Vac 30 Vac 34600 34600 34600 30 Vac 34463 34463 34463 F44 346000 on = 5 on = 4 on = 3 5 6 7 8 3 4 34600 30 Vac NC C NO L 30 Vac 34600 30 Vac 34600 warning Configure the handsets starting from n = Configure and insert the Jumpers with the system SwITCHEd. Also every time the configuration is modified the power supply to the system must be switched off and on again, waiting about minute. we recommend that the video handsets are configured using the software supplied with the product Use of the actuator is necessary for the staircase light service or generic actuations. For the Entrance Panel, all the pushbutton panels of the wire range can be used. Move to on the microswitch, on the Video handset or audio handset, which ends the line. Fit a 9 configurator to be inserted in S on the speaker module for the general call; do not insert any configurator in n. The audio video answering machine can only be used on video handset item 34463 34463 34463 on = = MY HOME - VIDEO DOOR ENTRY AND HOME VIDEO SURVEILLANCE SYSTEM 34300 PL S+ S- EP ITEM DESCRIPTI PS S B = = T = S = 9 d 34300 34463 346000 34600 F44 34600 PS S Flush mounted Linea 000 Metal entrance panel Polyx Memory Display video handset System power supply Additional power supply Audio/video node Staircase light actuator (optional) Door lock release pushbutton panel Electrical door lock 379
MY HOME - VidEO door ENTrY and HOME VidEO SurVEillaNCE SYSTEM - WIRING DIAGRAMS One-family system with max. 6 cameras or entrance panels device = To other handsets / apartment interfaces 34930 To other handsets / apartment interfaces d B F44 346000 O U T O U T O U T 3 O U T 4 O U T I N I N I N I N 3 I N 4 30 Vac F44 O U T O U T O U T 3 O U T 4 O U T I N c I N I N I N 3 I N 4 PE = = T = S = 9 3499 PL S+ S- = Z = A = PL = 3499 = Z = 39670 39670 A = PL = = 3 Z = A = PL = 39670 Cam.3 PS S ITEM DESCRIPTI 380 Cam. Cam. 3499 34930 F44 346000 3499 39670 EP PS S Cam-Cam3 Cam4-Cam7 Line terminator Axolute Video Station Nighter Audio/video node Power supply Linea 000 Metal EP wire outdoor camera Entrance panel Door lock release pushbutton (optional) Electrical door lock Outdoor camera Indoor camera
warning when the nodes are used in cascade, the distances of the various lines are halved. Cam. 4 O U T I N O U T O U T O U T 3 O U T 4 I N I N I N 3 I N 4 F44 F44 F44 Cam. 5 Cam. 6 Cam. 7 O U T I N O U T O U T O U T 3 O U T 4 I N I N I N 3 I N 4 3499 3499 To other entrance panels or other common cameras(configured with P= 8 P= ) O U T I N For the Entrance Panel, all the pushbutton panels of the wire range can be used. All the advanced video handsets of the wire range may be installed. only use one output for each node and allow for a terminator item 3499 to be connected to the SCS clamp Configure advanced handsets using a PC and Software supplied. By entering in the first seats of the P configurators, the microphone of the wire cameras is excluded (this function is only possible for cameras 0 to 9. The microphone cannot be excluded on the other cameras). O U T O U T O U T 3 O U T 4 I N I N I N 3 I N 4 3499 To other entrance panels or other common cameras(configured with P= P= 5) MY HOME - VIDEO DOOR ENTRY AND HOME VIDEO SURVEILLANCE SYSTEM = 4 Z = A = PL = = 5 Z = A = PL = = 6 Z = A = PL = P = = 7 Z = A = PL = PL = PL = PL = PL = COLOUR INDOOR CAMERAS AVAILABLE IN THE FOLLOWING FINISHES: 39658 39659 39657 39663 3966 3966 LIGHT LIGHT TECH LIVING AXOLUTE - WHITE AXOLUTE TECH AXOLUTE - ANTHRACITE 38