386 MY HOME Video door entry and home video surveillance system
CTENTS MY HOME - Video door entry and home video surveillance system General features. 388 General rules for installation. 408 Wiring diagrams. 4 Video door entry and home video surveillance system MY HOME 387
GENERAL FEATURES System composition The wire video door entry system uses the same SCS technology of all the MY HOME applications Regardless of system complexity, the functions needed, and the number of video handsets, all the devices are connected using the same wire cable, and are configured univocally In order to increase the system safety level, it is possible to connect wire indoor and outdoor cameras, the which images will be displayed directly on the video handsets (home video surveillance function) If a higher level of safety is required, it will be possible to associate an IR sensor of the burglar-alarm system to each sensor In this way, in case of trespassing, both the camera and the video handset will activate automatically In order to complete a wire video door entry system, in addition to the Outdoor pushbutton panel and the handsets, a few accessory will be needed, connected to the wire 3 riser ( WirES) 4 Electric distribution board or My Home Flatwall Floor shunt System expansion module Entrance panel 388 MY HOME Video door entry and home video surveillance system
room. ENTrANCE panel: sends the call to the video handset(s) (available in various look and installation models). SYSTEM EXpANSI MODuLE: it can be used to increase the performance of the system, for room Polyx Memory display Video handset 6 example to increase the distance between the outdoor pushbutton panel and the video handsets 3. ELECTrIC DISTrIBuTI BOArD Or MY HOME FLATWALL: room 3 It enables the user to install D devices: SYSTEM POWER SUPPLY: powers the 5 and all the devices AUDIO/VIDEO NODE: mixes the room 4 audio and video signals from external sources (entrance panels, cameras, sound sources ) and retransmits them on the WIRE riser (in Apartment interface alternative the audio/video matrix can also be used) 4. FLOOr SHuNT: used for star-connecting 4 Axolute Eteris Video display apartments, hence saving a lot of cable In addition, it lets you reach the The apartment interface enables creating an independent system inside the apartment. in this way, it is possible to install apartment handsets with simultaneous switching on, entrance panels and dedicated cameras. maximum extension of the system 5. ApArTMENT TErFACE: used for isolating the apartment from the riser In this way, inside 6 Axolute Nighter video station the apartment it will be possible to install an independent system with the corresponding MY HOME 6 applications 6. VIDEO HANDSETS: audio-video terminal which enables you to receive calls and to see who is calling Using the icons of the OSD menu it is possible to manage and control MY HOME applications (Available in various look and installation models) Video door entry and home video surveillance system MY HOME 389
GENERAL FEATURES Simple installation The wire system can be used to create any type of systems, both for the villa and the apartment complex Furthest handset Entrance panel 600 metres THE SYSTEM MAY CLuDE: 3900 Apartments 3900 Apartment video entrance panel 5 Handsets for apartment 39 risers with indepedent sound mode 96 Video entrance panel 390 MY HOME Video door entry and home video surveillance system
Devices ENTrANCE panel Outdoor video pushbutton panel with colour camera It can be used to call the video handsets and to activate the associated door lock Available in various look and installation models Flush mounted entrance panel Wall entrance panel outdoor Axolute entrance panel Axolute Nighter & Whice Video Station Polyx memory display VIDEO HANDSETS Video handsets for the audio and video reception of entrance panel calls Their icons allow the user to manage the video door entry system, and the MY HOME functions Available in various look and installation models Axolute video display DOOr CAMErAS WIRE indoor colour camera that can be connected directly to the system SCS Microphone for the room monitoring function Available in the AXOLUTE, LIVG, LIGHT and LIGHT TECH versions To be completed with the corresponding front cover plates cameras with front cover plates Video door entry and home video surveillance system MY HOME 39
GENERAL FEATURES Devices Apartment interface SYSTEM EXpANSI MODuLE Used to increase the number of video handsets connected to the system and to achieve maximum installation distance System expansion module outdoor camera ApArTMENT TErFACE To create a dedicated system inside the Apartment, separate from the apartment complex riser In the apartment, it will therefore be possible to create a video door entry system with dedicated entrance panels and cameras, integrated with the other MY HOME systems OuTDOOr CAMErA WIRE outdoor colour camera with 6 mm fixed optics to be connected directly to the SCS Protection index: IP65 ACTuATOrS Used for the control of electric locks, or the management of generic loads (e g staircase lights, call repetition, etc ) door lock actuator FLOOr SHuNT The floor shunt can be used to create star wiring systems Its use is compulsory for installation in simultaneous switching on systems Floor shunt Actuator for generic loads 39 MY HOME Video door entry and home video surveillance system
Audio/video node MuLTICHANNEL MATrIX It functions is that of an advanced audio/video mixing device It has 4 sound source inputs and 4 inputs for video door entry system/ cameras, which can be distributed simultaneously To be used in alternative to the audio/video node, in MY HOME systems with integrated video door entry system and sound system Video adapter AuDIO/VIDEO NODE AND VIDEO ADApTEr They perform the function of audio/ video mixers, for the connection to the system of entrance panels and video handsets The audio/video node can be used to connect up to 4 entrance panels / cameras and up to 4 risers The video adapter on the other hand can be used to connect entrance panels and riser (or entrance panel and risers) during presetting, the inclusion of the audio/video node is recommended, to allow for future system expansions. Multichannel matrix MuLTIMEDIA TOuCH SCrEEN 0" Touch Screen display for the management and the control of MY HOME applications It can be used to answer video door entry system calls, and to display images from the cameras connected to the system It manages audio, video, and WEB multimedia contents through the USB connection It has an SD card slot, and LAN connection To be completed with the surround plate Multimedia Touch Screen Video door entry and home video surveillance system MY HOME 393
GENERAL FEATURES Example - Villa E-FAMILY VIDEO DOOr-ENTrY SYSTEM WITH TErCOM BETWEEN VIDEO HANDSETS Nighter Video Station Whice Video Station Audio/video node Power supply Entrance panel 394 MY HOME Video door entry and home video surveillance system
LiViNg room room reception room on 34930 34930 34930 = 5 = = = 4 = 3 3493 3493 room KiTcHEN F44 346000 O UT3 4 34300 = T = S = 9 I N 3 4 SC S 30 Vac S Item DescrIptIon QUAntIty 34300 F44 346000 34930 3493 S Entrance panel Audio/video node Power supply Nighter Video Station Whice Video Station Electrical door lock 3 Max. 5 handsets Max. 00 metres between the entrance panel and the last handset S = Electric door lock 8 V 4 A impulsive 50 ma holding current NoTE : We recommend that the video handsets are configured using the software supplied with the product NoTE : When a call is received, only the handset configured with n= comes on Video door entry and home video surveillance system MY HOME 395
GENERAL FEATURES Example - Villa E-FAMILY VIDEO DOOr-ENTrY SYSTEM WITH OuTDOOr CAMErAS Nighter Video Station Whice Video Station Polyx Memory display Audio/video node Power supply outdoor camera Entrance panel 396 MY HOME Video door entry and home video surveillance system
Linving room Room Reception room 34463 34930 34930 = = = 5 = 4 = 3 3493 3493 ROOM KITCHEN 3499 O UT3 4 F44 346000 = = T = S = 9 I N 3 4 SC S 30 V = Z = A = PL = S 39670 39670 = Z = A = PL = Item Description QUANTITy 3499 39670 F44 346000 34930 3493 34463 S Entrance panel Outdoor camera Audio/video node Power supply Video Station Nighter Whice Video Station Polyx Memory Display Electrical door lock Max. 5 handsets Max. 00 metres between the entrance panel and the last handset S = Electric door lock 8 V 4 A impulsive 50 ma holding current NotE : We recommend that the video handsets are configured using the software supplied with the product Nota : The answering machine function is available only using the 34463 video handset, and can only be activated on video handset (the one configured with N=) Nota 3: When a call is received, only the Handset configured with N= comes on Video door entry and home video surveillance system MY HOME 397
GENERAL FEATURES Example 3 - Apartment ApArTMENT WITH DEDICATED ENTrANCE panel AND private CAMErAS outdoor camera indoor camera Axolute Eteris Video display Apartment interface Audio/video node Power supply Polyx Memory display 398 MY HOME Video door entry and home video surveillance system
34463 = 5 P = Apartment extension 34463 349340 = 4 P = = P = C OK 34463 34463 = 3 P = = P = O UT3 4 F44 346000 I N 3 4 SC S 30 Vac 3966 Building riser = 5 M = 3 346850 3499 = T = S = 9 S 39670 = 3 Z = A = PL = = Z = A = PL = Building riser Item Description QUANTITy 3499 39670 3966 346000 F44 346850 34463 349340 S L000 Entrance panel Outdoor camera Axolute indoor camera Power supply Audio/video node Apartment interface Polyx memory display Eteris Video Display Electrical door lock 4 Max 5 video handsets, apartment EP and apartment cameras Note : We recommend that the video handsets are configured using the software supplied with the product NOTE : Configure the entrance panels and the apartment cameras starting from (P=) NOTE 3: The audio/video answering machine can only be activated on one 34463 video handset (the one configured with N=-) Video door entry and home video surveillance system MY HOME 399
GENERAL FEATURES Example 4 - Complexes of small houses MuLTI-FAMILY SYSTEM WITH SGLE DEpENDENT DWELLGS AND AT LEAST E COMM ACCESS pot Entrance panel Apartment interface Audio/video node Power supply 400 MY HOME Video door entry and home video surveillance system
TMP PL RC C NC NO/S+ S Inside of the apartment Inside of the apartment see previous diagram see previous diagram SMALL HOUSE 35 SMALL HOUSE 99 346850 346850 N = 3 = 5 M = 3 N = 9 = 9 M = 3 Inside of the apartment Inside of the apartment see previous diagram SMALL HOUSE see previous diagram SMALL HOUSE 6 346850 = M = 3 N = = 6 M = 3 346850 F44 346000 34660 SCS SCS S = P = T = JMP JMP max 50 m 30 Vac = P = S = The EP must be configured and programmed using the software supplied with the product Item Description QUANTITy 34940 3393 33933 F44 346000 346850 S 34660 Axolute entrance panel Front cover plate Flush mounted box Audio/video node Power supply Apartment interface Electrical door lock Door lock actuator - 99 34940 Max 99 apartment interfaces and apartment complex entrance panel Max 50 metres between entrance panel and audio/video node Video door entry and home video surveillance system MY HOME 40
GENERAL FEATURES System functions Call Communication Call Apartment Apartment The handset rings and the monitor switches on The conversation cannot be heard All the handsets, on the same call, ring and switch on the monitor. THE CALL Pressing the call pushbutton on the entrance panel, the system generates a signal that is only recognised by the video handsets the call is addressed to (the call will have to be answered within 30 seconds from the moment the pushbutton is pressed) Each VIDEO handset is configured in a unique specific way When the call is received, the video handset rings and the monitor switches on Press the pushbutton to establish the communication (maximum duration of the communication is minute) with the entrance panel Press again to stop the communication and switch the monitor off CVErSATI SECrECY During the conversation between the entrance panel and the video handsets, all external panels and handsets that are not involved in the conversation are temporarily excluded in order to guarantee the privacy of video door entry conversations When calling from an entrance panel that is temporarily excluded, a time-out tone will be heard, to indicate that the extension line is momentarily busy SIMuLTANEOuS SWITCHG With video handsets, simultaneous switching on of the monitor is also possible: upon arrival of the call, all handsets ring and the monitors of all video handsets switch on When the call is answered, only the monitor of the video handset communicating with the entrance panel will remain on In order to set this function, all the video handsets but one must be powered locally using an additional power supply, item 34600 40 MY HOME Video door entry and home video surveillance system
Call CLAK Pressing the door lock key will open the gate associated with the handset. The staircase light function will switch on the system lights connected to a special actuator Each time the self-switching on key is pressed the images displayed change. DOOr LOCK pushbutt The video handsets are fitted with a door lock pushbutton Pressing this pushbutton will open of one of the door locks of the system With the system at rest, the pressure of the pushbutton will cause the opening of the door lock of the entrance panel associated with the handset during the P configuration of the handset itself On the other hand, if the pushbutton is pressed during the call, the door lock associated to the entrance panel making the call will be opened THE STAIrCASE LIGHT FuNCTI The video handsets are equipped with an icons menu This function activates a relay for the timed switching on of lights and the opening of the gate The function can be performed by installing the actuator item 34600, appropriately configured SELF-SWITCHG pushbutt By pressing the self-switching on pushbutton while the videohandset is at rest, a connection will be established with the entrance panel associated with the handset during the P configuration of the handset itself Pressing repeatedly on the selfswitching on pushbutton, will scroll through the various entrance panels and the cameras connected to the system Video door entry and home video surveillance system MY HOME 403
GENERAL FEATURES System functions Apartment Call TeRCOM call item 346850 apartment interface enables the intercom function between the devices within the one apartment and the various apartments Master Slave Apartment When a call is received, the MASTEr comes on, while the SLAVE will only ring. APArTMENT MASTEr-SLAVE FuNCTI For multi-family installations the MASTER-SLAVE function is available: when the call is received, all the apartment handsets ring, but only the monitor of the video handset configured as master comes on When the auto-switching on key of a SLAVE is pressed, the monitor of the MASTER handset turns off, while the monitor of the SLAVE itself turns on (without necessarily establishing communication with the entrance panel) If the connection key of a SLAVE is pressed, the MASTER monitor turns off and communication with the audio-video entrance panel is established TErCOM The system offers an intercom function, with up to 3 minutes communications between videohandsets: From different apartments Within the same apartment If the apartment has an apartment interface - item 346850 - or is a one- family apartment, each videohandset of the apartment can be called individually The TERCOM connection can be established at the same time as other external connections The TERCOM connection can be simultaneous to other connections external to the apartment If the apartment does not have an apartment interface - item 346850 - any apartment handset can call all other apartment handsets The TERCOM connection will not occur at the same time as external connections Any call received by an EP, even to any other apartment, will terminate the TERCOM connection APArTMENT 404 MY HOME Video door entry and home video surveillance system
We are currently out... Answering machine active MESSAGGIO MESSAGGIO MESSAGGIO 3 MESSAGGIO MESSAGGIO MESSAGGIO 3 MESSAGGIO MESSAGGIO MESSAGGIO 3 MESSAGGIO MESSAGGIO MESSAGGIO 3 MESSAGGIO MESSAGGIO MESSAGGIO 3 Playback of sounds and images recorded by the answering machine VIDEO DOOr ENTrY SYSTEM ANSWErG MACHE FuNCTI Function available only using the POLYX MEMORY DISPLAY video handset, item 34463 It is possible to record voice and images of a call from an entrance panel It is also possible to record an audio message to play back on the entrance panel following an unanswered call The video door entry system message can be recorded in ways: STILLS: the message includes a picture of the visitor and the recorded audio message (60 messages max) VIDEOS: the message includes a video feed (duration 6 seconds) and the recorded audio message (8 messages max) Each message will be given a progressive number, which will be displayed on the video handset, together with the date and time information Video door entry and home video surveillance system MY HOME 405
GENERAL FEATURES System functions ir detector and associated cameras dinner is served! on up pager FuNCTI SYSTEMS TEGrATED WITH SOuND SYSTEM By pressing the conversation pushbutton on the video handsets, it is possible to broadcast a message through all the loudspeakers of the sound system The involved video handsets must be powered locally From the video handset menu it is possible to control and display the functions of the sound system through the icons of the menu itself NoTE: function possible by configuring the video handsets using the software supplied with the product. SCENArIO CTrOL FuNCTI SYSTEMS TEGrATED WITH AuTOMATI SYSTEM From the video handsets, it is possible to recall the scenarios saved in the F40 scenarios NoTE: function possible by configuring the video handsets using the software supplied with the product. SWITCHG CAMErA FuNCTI SYSTEMS TEGrATED WITH THE BurGLAr ALArM SYSTEM It is possible to associate a zone of the burglar alarm to the cameras When an alarm situation is detected, the images recorded by the camera are displayed on the video handset Using the appropriate icons of the menu of the video handset, it is possible to monitor the status of the burglar-alarm system: for example, the status of the burglar-alarm (armed/disarmed), active zones, alarms occurred NoTE: function possible by configuring the video handsets using the software supplied with the product. 406 MY HOME Video door entry and home video surveillance system
0.5 C off CUCA A + +.5 (+) 8.5 C 0.5 C off CUCA A + +.5 (+) 8.5 C SupErVISI FuNCTI SYSTEMS TEGrATED WITH THE TEMpErATurE CTrOL SYSTEM From the video handset menu, it is possible to display the status of the temperature control system Using the appropriate icons it is possible, for example, to change the temperature parameters, and display the status of the probes NoTE: function possible by configuring the video handsets using the software supplied with the product. Video door entry and home video surveillance system MY HOME 407
General rules for installation System composition The system is classed as SELV (Safety Extra Low Voltage) due to the fact that it is powered by non grounded safety double insulation independent power supplies with a max. voltage of 5 Vac (effective) or 60Vdc noninverted voltage. In addition, all BTicino devices are double insulated. The conformity to SELV classification is only guaranteed only subject to FULL COMPLIANCE with current installation regulations and with the GENERAL RULES FOR STALLATI relating to each single device and cable, making up the installation. BASIC ELEMENTS OF THE VIDEO SYSTEM In order to install a system it is necessary to purchase, in addition to the entrance panel and the handset, also the 346830 video adapter, or the F44 audio/video node, and the 34684 floor shunt with the function of distributing the video signal. Video adapter The video adapter is used to connect Video adapter entrance panels and handsets to a wire video system A maximum of 3 connections are allowed on the video adapter. TK PI Power supply Video handset PS Video adapter Video entrance panel Entrance panels Handsets TK PI PS Power supply 346000 A maximum of 3 connections are allowed on the video adapter. (*) Entrance panels Handsets Entrance panel Handsets TK PI TK PI PS PS Connection of entrance panels and a riser for the handsets Connection of entrance panel and risers for the handsets (*) If either an interface is connected to the entrance panel, only one connection on the TK terminal of the video adapter is possible. 408 MY HOME Video door entry and home video surveillance system
SCS AuDIO/VIDEO NODE Or VIDEO MATrIX Audio/VidEo NodE The F44 audio/video node and the F44M video matrix must be used in alternative to the video adapter when more than entrance panels must be installed in the system, or when more than risers are needed Power supply Video handset The use of the audio/video node or the video matrix is however recommended, to allow for future Video entrance panel To the handsets my HOme integrations, system expansions, and/or addition of Audio/video node Power supply cameras. Allow for one output of the audio/ video node, or the video matrix, for SCS each video door entry system video handset with table-top installation To the entrance panels/cameras FLOOr SHuNT When creating video systems, the use of the floor shunt, item 34684 is recommended This will provide important savings on the cable to be used This is particularly suitable for multi-family systems, when more than one living unit on the same floor or in multi-family systems, where max distance between the entrance panel and all handsets is needed The Floor shunt enables star connection of up to 4 apartments with a max of 3 handsets for Apartment (max handset per output, if set in simultaneous switching on) One output of the audio/video node should be dedicated to each tablemounted video handset installed FLoor SHuNT Apartment Apartment 3 Apartment Apartment 4 ART. 34684 riser wire riser For each output: max. 3 video handsets or bells in the same apartment max. video handset in simultaneous switching on max. table-mounted video handset Video door entry and home video surveillance system MY HOME 409
SC S SC S SC S SC S GENERAL RULES FOR STALLATI System composition SYSTEM EXpANSI MODuLE 34685 MOD = 0 (SYSTEM EXpANSI MODE) To be used for system expansion, in order to: Regenerate the video signal and have a further 00 m available after the interface (using the 336904 cable) Increase the number of devices connected to the Use a max of 3 modules, configured using the MOD = 0 in cascade As far as the system composition, distances and topology are concerned, within the system section, the system expansion module item 34685 must be considered as a handset On the other side, within the system section it should be considered as an entrance panel Mod = 0 Entrance panel System section System section F44 346000 34685 F44 346000 00 m 00 m 34685 34685 34685 34685 max. item 34685 with Mod = 0 for each output 346000 Entrance panel F44 346000 F44 The in clamp of the system expansion modules configured with Mod = 0 must be connected to a dedicated output of the F44 audio/video node or the 34684 floor shunt (as a handset with local power supply). 40 MY HOME Video door entry and home video surveillance system
SC S SC S SC S SYSTEM EXpANSI MODuLE ITEM 34685 MOD = 5 (DEpENDENT riser MODE) This is used in buildings to have risers with riser entrance panels and independent audio and video functions Mod = 5 riser system section (with independent audio) riser system section (with independent audio) riser riser F44 346000 F44 346000 riser entrance panel 34685 34685 riser entrance panel common system section Entrance panel F44 346000 in the common system section, for the purpose of system composition, distances and layout, the system expansion modules must be treated as a handsets. on the other hand, in the riser system sections they must be treated as entrance panels. The building entrance panel must be made with alphanumeric or numeric call module Video door entry and home video surveillance system MY HOME 4
SC S SC S GENERAL RULES FOR STALLATI System composition ApArTMENT TErFACE ITEM 346850 This is used to have an apartment system independent from the building In this way, the apartment system can have private cameras and entrance panels and can be integrated with all the MY HOME applications As far as the system composition, distances and topology are concerned, within the building system, the interface item 346850 must be treated as a handset On the other side, within the apartment system, it should be treated as an entrance panel configured with P = 0 Apartment block system section For the completion of the system, any type of cable can be used (including existing cables). Maximum performance and distances are achieved using the 346850 F44 Apartment system section 346000 Handset 336904 cable. Entrance panel F44 346000 Apartment entrance panel Apartment camera 4 MY HOME Video door entry and home video surveillance system
Configuration To configure means to program the system. This occurs assigning an identification and operational mode number to the devices. This operation is made inserting in the appropriate seats some configurators (numbered from 0 to 9), using a clamp provided with the power supply or contained in the case of the configurators or using the configuration software (recommended). The configurators can be purchased in a case I 0-9 350K or individually 3 4 5 350/ 350/ 350/3 350/4 350/5 6 7 8 9 0 S L A A seat is left empty corresponds to the configuration of a zero. 350/6 350/7 350/8 350/9 350/0 350/SLA In the system exist two different numerations to identify respectively the entrance panels (EP) and the handsets. The numeration of the EP (0-96) is generally identified by P, while the address of the handsets (0-99) is identified by N. On the EP, in addition to the P address it is necessary to configure also the N address relating to the handset from which we would start to call. On the handsets in addition to the N address, it is necessary to configure in P the EP associated to the same handset, or the entrance panel on which the door lock and autoswitching controls work when the handset is switched. = S = Example of configured system and its operation Door lock and auto-switching controls in pause from apartment Apartment Apartment 5 Call apartment = Call apartment 5 Door lock and auto-switching controls in pause from apartment 5 N = = 5 P = = S = Should occur the need to modify the configuration of a device, it is necessary, in addition to change the configurators, take off the power supply to the whole system, wait minute, and then provide voltage again. For each device exist also particular configurations which will be detailed in the product technical sheet. Video door entry and home video surveillance system MY HOME 43
34685 34685 SCS 34685 34685 34685 34685 GENERAL RULES FOR STALLATI Configuration SYSTEM EXpANSI MODuLE ITEM 34685 The system expansion module can be configured in different ways: (the addresses in M with MOD = 0 and MOD = 5 do not conflict with each other) MOD = 0 for system expansion M = specific progressive number for interface 34685 Mod = 0 M = Video handset Entrance panel Video handset Mod = 0 M = 34685 Mod = 0 M = Mod = 0 M = Mod = 0 M = 3 Mod = 0 M = 4 34685 34685 34685 34685 F44 Entrance panel 44 MY HOME Video door entry and home video surveillance system
34685 346850 34685 34685 346850 MOD = 5 for independent audio risers M = specific progressive number indicating the riser number common entrance panel independent WirE riser independent WirE riser independent WirE riser Mod = 5 M = Mod = 5 M = Mod = 5 M = 39 34685 34685 34685 For the common entrance panel, the handsets have address M (riser number) x 00 + N (handset for the riser). Es. Handset N = 0 of the riser for the common EP = x 00 + 0 = 0 ApArTMENT TErFACE 346850 The apartment interface is configured correct configuration Wrong configuration as a normal handset The interface must be configured in a specific unique way No other handset can N = 7 N = 6 be configured in N using the same address, in the same system or on the same riser with independent audio The factory device is configured with N = 6 N = 5 M = 3 T EXT N = 5 N = 5 SYSTEM T EXT SYSTEM WirE BuS 346850 WirE BuS 346850 Video door entry and home video surveillance system MY HOME 45
General rules for installation The wiring SYSTEM WIRG The systems can also be wired in modes: in-out wiring STAR wiring with floor shunt 34684 (recommended). In-out wiring In-out wiring is connected directly on the terminal of the appliances which are connected to the system. Each riser must be terminated by positioning the micro switch of the last handset to. In-out wiring is particularly indicated for one and two-family systems and for vertical or horizontal multi-family systems (with the homes in rows). In-out wiring STAR wiring The star wiring is made connecting the individual apartment to an output of the floor distribution block Item 34684. Each line must be terminated by positioning the micro switch of the last appliance to. STAR wiring is particularly suitable for multi-family systems, when more than one living unit on the same floor or in multi-family systems, where max. distance between the entrance panel and all handsets is needed. On each output of the shunt it will be possible to connect up to 3 handsets maximum. An output of the floor distribution block must be dedicated to each handset with simultaneous switching on or table-top base installation. STAR wiring Apartment n Handsets Apartment Apartment 5 Apartment Apartment 3 Apartment Apartment 3 Apartment 4 Apartment 6 Apartment 7 Apartment 8 Apartment 4 wire 34684 34684 wire 46 MY HOME Video door entry and home video surveillance system
COMBED WIrG Both wiring methods described previously can be used together, for the realization of more articulated systems The combined wiring (- and Star) allows to execute wiring systems in order to satisfy the greatest quantity of requests Floor distribution blocks outputs can be used to connect a single device or to generate an apartment line (on which max 3 devices can be connected, without using the apartment interface item 346850) To the Bus handset can be connected in - floor distribution blocks or handsets Apartment n Apartment 3 Apartment Apartment 34684 The assignation of the handsets to the apartments occurs through configuration (for further information see technical sheets for the individual devices) Entrance panel BuS Floor shunt 00 m Video entrance panel Video door entry and home video surveillance system MY HOME 47
OF F OF F OF F OF F 346850 346850 34685 34685 OF F OF F T EXT 346850 34685 GENERAL RULES FOR STALLATI Installation of entrance panels, handsets and interfaces T EXT T 60 65 cm EXT 60 65 cm NO HEIGHT OF THE HANDSET When installing the handsets, including standard or video handsets, it is recommended that the devices are positioned at a height of 60 65 cm (top edge) Note: recommended installation heights, unless otherwise required by local regulations. TErFACES ITEM 346850 AND 34685 The interfaces item 346850 (apartment interface) and item 34685 (system expansion module) cannot be installed in a manhole For their installation, a sealed electric cabin with D rail must be used (D switchboard) HEIGHT OF THE ENTrANCE panel When installing the Entrance panel, it is recommended that the pushbutton panel is installed at a height of 60 65 cm (top edge) The camera must not be installed in front of light sources, or in places where the subject being filmed is in the shadow If this condition cannot be respected, the picture will not have much contrast in the darker areas This is because the brightness is selfregulated on the lighter part of the picture To solve these problems change the camera installation height, normally 60 65 cm, to a height of 80 cm and direct the lens downwards to improve the quality of the shots In scarcely lit areas, the installation of an additional light source is recommended 48 MY HOME Video door entry and home video surveillance system
346850 346850 34685 34685 SCS System performance The following information provides general parameters on the maximum distances that can be achieved, and the features of the cables to be used. The type of system considered is a single family system or system below an apartment interface. WARNG: For installation solutions or types other than those shown, the distances and the current absorptions can be calculated using the You Diagram software (which can be downloaded free of charge from the website www.professionisti.bticino.it technical service software and diagrams). Also refer to the specific technical documentation ( wire system Technical Guide). Furthest video handset T EXT 346850 34685 MOD = 0 e MOD = 5 MAXIMUM DISTANCE LE A ENTRANCE PANEL - FURTHEST HANDSET Cable section mm normal cables > 0. mm or L4669 336904 twisted telephone pair 0.8 mm one pair of the multi-pair data cable, item C988U/5E 5 HANDSETS in/out 50 m 00 m 40 m 40 m 5 one-fam Handsets/DOOR EP 50 m 00 m 00 m 70 m 5 one-fam Handsets/EP with local power supply 50 m 00 m 40 m 70 m MAXIMUM DISTANCE LE C POWER SUPPLY FURTHEST HANDSET Cable section mm normal cables > 0. mm or L4669 336904 twisted telephone pair 0.8 mm one pair of the multi-pair data cable, item C988U/5E 5 Handsets in/out 50 m 0 m 70 m 50 m 5 Handsets (with shunts) 50 m 0 m 70 m 50 m LE A* LE C* 346000 346830 TK PI PS O 346000 F44 MAXIMUM DISTANCE LE B ENTRANCE PANEL POWER SUPPLY Cable section mm normal cables > 0. mm or L4669 336904 twisted telephone pair 0.8 mm pushbuttons 50 m 00 m 5 m 90 m one pair of the multi-pair data cable, item C988U/5E DOOR EP 0 m 50 m 30 m 0 m Entrance panel with local power supply 50 m 00 m 40 m 0 LE B * Entrance panel 346850 34685 MOD = 0 T e EXT MOD = 5 MAXIMUM DISTANCE LE D ENTRANCE PANEL DOOR LOCK Cable section mm 0.8 BTicino SCS cable - item L4669 BTicino SCS cable - item 336904 S+ S- clamps 30 m 30 m 50 m 00 m LE D* Door lock (*) Max. variable distance. Note: in systems with apartment interfaces only (in/out connection) the distance of LE C to be taken into account is 00 m (with BTicino cable 336904) Video door entry and home video surveillance system MY HOME 49
GENERAL RULES FOR STALLATI System performance SYSTEM WITH ApArTMENT TErFACE AND SYSTEM EXpANSI MODuLE Up to 3 interfaces, items 346850 Audio/video connection between the entrance panel and the video handset (3 passages maximum) = ok and 34685 may be installed in cascade Cascade interfaces are those crossed by an audio/video connection (Entrance panel HANDSET) or (HANDSET HANDSET, e g TERCOM) Only of these interfaces (selected by the user) retransmit the signal for 00 metres Video entrance panel 34685 max 00 m 34685 The maximum distance between max. 00 m EP and the furthest handset is 600 metres Each LE (EP TERFACE), (TERFACE TERFACE) and 34685 34685 (TERFACE H) must be 00 metres maximum (with BTicino cable 336904) The end cap of the system max. 00 m expansion module configured with M=0 MUST be wired and considered as a H with local power supply max. 00 m It must also be connected to an output of the Audio/video node F44, or the Floor shunt 34684 346850 T EXT 346850 40 MY HOME Video door entry and home video surveillance system
CNECTI OF 6 AUDIO /VIDEO Entrance panels Or cameras Video door entry system/apartment interface risers O UT3 4 F44 346000 3 4 SC S F44 F44 F44 F44 O UT3 4 O UT3 4 O UT3 4 O UT3 4 3 4 SC S 3 4 SC S 3 4 SC S 3 4 SC S 3499 3499 3499 3499 4 entrance panels or cameras 4 entrance panels or cameras 4 entrance panels or cameras 4 entrance panels or cameras Video door entry and home video surveillance system MY HOME 4
WIRG DIAGRAMS One-family system with EP and 5 intercommunicating video handsets e device 3 = 3 device = device = 34463 34463 34463 c device 5 device 4 34463 34463 = 5 = 4 WArNiNg configure the handsets starting from N = configure and insert the Jumpers with the system SWiTcHEd off. Also every time the configuration is modified the power supply to the system must be switched off and on again, waiting about minute. The intercom function is operating even with a lack of entrance panel connection. We recommend that the video handsets are configured using the software supplied with the product. A use of the actuator is necessary for the staircase light service or generic actuations. B For the Entrance Panel, all the pushbutton panels of the wire range can be used c Move the micro switch of the last video or audio handset at the end of the line to the on position d Fit a 9 configurator to be inserted in S on the speaker module for the general call; do not insert any configurator in N. e The audio video answering machine can only be used on video handset (the one configured with N=) Nota 3: When a call is received, only the Handset configured with N= comes on Electric distribution board or My Home Flatwall PL S+ S- O UT3 4 F44 346000 34600 PS S PE 3 4 SC S A 30 Vac 5 6 7 8 3 4 NC C NO 34300 B 30 Vac L = = T = S = 9 d Item 34300 34463 34600 346000 F44 L EP PS S DescrIptIon Linea 000 Metal EP Polyx Memory Display video handset Staircase light actuator (optional) Power supply Audio/video node Staircase light Entrance panel Door lock release pushbutton (optional) Electric door lock 8V 4A impulsive 50mA holding current 4 MY HOME Video door entry and home video surveillance system
Two-family systems with EP, 3 handsets per home and intercom between apartments HoME = 34463 SLAVE A HoME = = 34463 A SLAVE SLAVE c WArNiNg configure and insert the Jumpers with the system SWiTcHEd off. Also every time the configuration is modified the power supply to the system must be switched off and on again, waiting about minute. it is possible to install a maximum of 3 video handsets for apartment. We recommend that the video handsets are configured using the software supplied with the product configure Master and Slave devices using the software When a call is received, the MASTEr rings and switches on, while the SLAVE will only ring. if the call is answered from a SLAVE unit, the master unit switches off again, while the monitor of the SLAVE from where the call is answered comes on." = 34463 SLAVE = 34463 MASTEr A Move the micro switch at the back of the last video or audio handset at the end of the line to the on position B For the Entrance Panel, all the pushbutton panels of the wire range can be used. c The audio video answering machine can only be used on video handset (the MASTEr video handset) = 34463 MASTEr 34463 c Electric distribution board or My Home Flatwall PL S+ S- O UT3 4 F44 346000 PE PS S 3 4 SC S 30 Vac 34300 = = T = S = Item 34300 34463 346000 F44 EP PS S DescrIptIon Two-family Linea 000 Metal entrance panel Polyx Memory Display video handset Power supply Audio/video node Entrance panel (main) Door lock release pushbutton (optional) Electric door lock 8V 4A impulsive 50mA holding current Video door entry and home video surveillance system MY HOME 43
WIRG DIAGRAMS One-family system with EP and outdoor cameras = 3493 3493 device device BuS Pi (5 handsets max.) WArNiNg configure and insert the Jumpers with the system SWiTcHEd off. Also every time the configuration is modified the power supply to the system must be switched off and on again, waiting about minute. We recommend that the video handsets are configured using the software supplied with the product. End with the micro switch of the last line/riser handset in the on position. A For the Entrance Panel, all the pushbutton panels of the wire range can be used. = B Fit a 9 configurator to be inserted in S on the Entrance panel to make a general call. Nota: When a call is received, only the Handset configured with N= comes on O UT3 4 Electric distribution board or My Home Flatwall F44 346000 3 4 SC S 30 Vac PL S+ S- PE A PL S+ S- PE A 39670 39670 cam. cam. PS = = T = S = 9 B S PS 3499 3499 S = = T = S = 9 B = Z = A = PL = = 3 Z = A = PL = Item 3499 3493 39670 346000 F44 PE-PE PS-PS S-S Cam.-Cam. DescrIptIon Linea 000 Metal entrance panel Whice Axolute Video Station wire outdoor camera Power supply Audio/video node Entrance panel Door lock release pushbutton (optional) Electric door lock 8V 4A impulsive 50mA holding current wire outdoor camera 44 MY HOME Video door entry and home video surveillance system
PRI 34600 PRI: 0 40 V~ 75 65 ma 47/63 Hz SCS: 7 Vdc 600 ma PRI 34600 PRI: 0 40 V~ 75 65 ma 47/63 Hz SCS: 7 Vdc 600 ma PRI 34600 PRI: 0 40 V~ 75 65 ma 47/63 Hz SCS: 7 Vdc 600 ma - - - SC S PRI 34600 PRI: 0 40 V~ 75 65 ma 47/63 Hz SCS: 7 Vdc 600 ma PRI 34600 PRI: 0 40 V~ 75 65 ma 47/63 Hz SCS: 7 Vdc 600 ma - - One-family system with 5 video handsets in simultaneous switching on 30 Vac 34600 34463 = 5 WArNiNg configure the handsets starting from N = configure and insert the Jumpers with the system SWiTcHEd off. Also every time the configuration is modified the power supply to the system must be switched off and on again, waiting about minute. We recommend that the video handsets are configured using the software supplied with the product use of the actuator is necessary for the staircase light service or generic actuations. 30 Vac 34600 34463 = 4 For the Entrance Panel, all the pushbutton panels of the wire range can be used. Move to on the microswitch, on the Video handset or audio handset, which ends the line. Fit a 9 configurator to be inserted in S on the speaker module for the general call; do not insert any configurator in N. The audio video answering machine can only be used on video handset item 34463 30 Vac 34600 34463 = 3 30 Vac 34600 34463 = F44 346000 O UT3 4 34600 30 Vac 34600 34463 3 4 30 Vac 5 6 7 8 NC 3 4 30 Vac C NO L = PL S+ S- PS S 34300 B PE = = T = S = 9 d Item 34300 34463 346000 34600 F44 34600 PS S DescrIptIon Flush mounted Linea 000 Metal entrance panel Polyx Memory Display video handset System power supply Additional power supply Audio/video node Staircase light actuator (optional) Door lock release pushbutton panel Electrical door lock Video door entry and home video surveillance system MY HOME 45
WIRG DIAGRAMS One-family system with max 6 cameras or entrance panels device = To other handsets / apartment interfaces 34930 To other handsets / apartment interfaces d B F44 346000 3 4 3 4 SCS 30 Vac F44 3 4 c 3 4 SCS PE = = T = S = 9 3499 PL S+ S- PS S = Z = A = PL = 3499 = Z = 39670 39670 A = PL = cam. cam. Item 3499 34930 F44 346000 3499 39670 EP PS S Cam-Cam3 Cam4-Cam7 = 3 Z = A = PL = 39670 cam.3 DescrIptIon Line terminator Axolute Video Station Nighter Audio/video node Power supply Linea 000 Metal EP wire outdoor camera Entrance panel Door lock release pushbutton (optional) Electrical door lock Outdoor camera Indoor camera 46 MY HOME Video door entry and home video surveillance system
SCS WArNiNg When the nodes are used in cascade, the distances of the various lines are halved. For the Entrance Panel, all the pushbutton panels of the wire range can be used. All the advanced video handsets of the wire range may be installed. only use one output for each node and allow for a terminator item 3499 to be connected to the ScS clamp configure advanced handsets using a Pc and Software supplied. By entering off in the first seats of the P configurators, the microphone of the wire cameras is excluded (this function is only possible for cameras 0 to 9. The microphone cannot be excluded on the other cameras). F44 F44 F44 3 4 3 4 3 4 3 4 3 4 SCS 3 4 SCS 3499 3499 3499 To other entrance panels or other common cameras(configured with P= 8 P= ) To other entrance panels or other common cameras(configured with P= P= 5) cam. 4 cam. 5 cam. 6 cam. 7 = 4 Z = A = PL = = 5 Z = A = PL = = 6 Z = A = PL = P = off = 7 Z = A = PL = PL = PL = PL = PL = colour InDoor cameras AVAILABLe In the FoLLoWInG FInIsHes: 39658 39659 39657 39663 3966 3966 LIGHT LIGHT TECH LIVG AXOLUTE - WHITE AXOLUTE TECH AXOLUTE - ANTHRACITE Video door entry and home video surveillance system MY HOME 47