RM410 Rack Mounting Kit Version 1.00 Edition 1, 12/2012 Quick Start Guide Hardware Installation Guide www.zyxel.com Copyright 2012 ZyXEL Communications Corporation
IMPORTANT! READ CAREFULLY BEFORE USE. KEEP THIS GUIDE FOR FUTURE REFERENCE. This guide shows you how to use the rack mounting kit to install the Switch in a rack. Graphics in this book may differ slightly from your product. Every effort has been made to ensure that the information in this manual is accurate. Related Documentation Module Hardware Installation Guide This guide shows how to install the power and fan modules in the Switch. User s Guide This guide shows how to use the Web Configurator to configure the Switch. CLI Reference Guide This guide explains how to use the Command-Line Interface (CLI) to configure the Switch. Web Configurator Online Help Click the help icon in any web configurator screen for help in configuring that screen and supplementary information. 2 RM410 Hardware Installion Guide
CHAPTER 1 Rack Mounting Kit 1.1 Installation Requirements Two front mounting brackets (short) and two rear mounting brackets (long). 16 M4 flat head screws and a #2 Philips screwdriver for attaching the brackets to the Switch. Eight rack screws (NO.10-32UNF) and a screwdriver for attaching the Switch (with attached brackets) to the rack. Rack depth can be from 90 to 120 cm. Note: Failure to use the proper screws may damage the unit. 1.1.1 Precautions Make sure the rack will safely support the combined weight of all the equipment it contains. The maximum weight a bracket can hold is 30.6 Kg. Make sure the position of the Switch does not make the rack unstable or top-heavy. Take all necessary precautions to anchor the rack securely before installing the unit. 1.2 Attaching the Brackets to the Switch Use the M4 screws (smaller than the rack screws) to attach the brackets to the Switch. 1 Position the smaller front mounting bracket on one side at the front of the Switch (the ports are at the front of the Switch), lining up the four screw holes on the bracket with the screw holes on the side of the Switch. 2 Use a #2 Philips screwdriver to install the M4 screws through the mounting bracket holes into the Switch. 3 Repeat step 2 to install the second front mounting bracket on the other side of the front of the Switch. RM410 Hardware Installion Guide 3
Chapter 1 Rack Mounting Kit 4 Position the bigger rear mounting bracket on one side at the rear of the Switch (the modules are at the rear of the Switch), lining up the four screw holes on the bracket with the screw holes on the side of the Switch depending on the depth of the rack. The brackets support rack depth of 90 cm, 100cm and 120 cm. 5 Use a screwdriver to install the M4 screws through the mounting bracket holes into the Switch. 6 Repeat step 4 to install the second rear mounting bracket on the other side of the Switch. Rear Bracket 120 cm rack depth or 100 cm rack depth or 90 cm rack depth Front Bracket You may now mount the Switch on a rack. Proceed to the next section. 1.3 Mounting the Switch on a Rack Use the rack screws (larger than the M4 screws) to mount the Switch with brackets on the rack. 4 RM410 Hardware Installion Guide
Chapter 1 Rack Mounting Kit 1 Position a front mounting bracket (that is already attached to the Switch) on one side of the rack, lining up the two screw holes on the bracket with the screw holes at the front of the rack. 2 Use a screwdriver to install the rack screws through the mounting bracket holes into the rack. 3 Repeat steps 1 and 2 to attach the other front mounting bracket on the other side of the rack. 4 Position a rear mounting bracket (that is already attached to the Switch) on one side of the rack, lining up the two screw holes on the bracket with the screw holes at the rear of the rack. 5 Use a screwdriver to install the rack screws through the mounting bracket holes into the rack. 6 Repeat steps 1 and 2 to attach the other rear mounting bracket on the other side of the rack. Rear Front RM410 Hardware Installion Guide 5