2014 AT&T Intellectual Property. All rights reserved. AT&T, Globe logo and other marks are trademarks of AT&T Intellectual Property.

Transcription

1 AT&T Business in a Box Quick Start Guide Please ensure that you have set-up the equipment before the date scheduled with your AT&T Order Manager for Test and Turn Up of your service

2 What s in the Box The following components are included in your router package: RJ11 modem cable Labelled ISE644 (Qty 1) AT&T Business in a Box 12 or 24 Port Base Unit Router Router power cable Site Documentation Package RJ48 T1 Cable Labelled ISE (Qty 1-4) 2

3 Understanding your AT&T Business in a Box Equipment AT&T Business in a Box 12 or 24 Port Base Unit Router (24 port depicted) Ethernet LAN Ports (12 or 24) Customer Provided Cable (RJ45) to IP Phones, PC s, Servers, etc. AT&T Provided Interconnect cables for Add-on s when ordered T1 Ports (4) Grey Cable(s) from SmartJack to Grey Port. When PRI interface to phone system is required a RED cable used in port #4 Modem Port Included Brown Cable from POTS jack to Brown Port Survivability Ports (2) Customer Provided Cable (RJ11) to customer provided POTS Jack Analog Phone Ports (6) Customer Provided Cable (RJ11) to customer key system, fax 3

4 Step 1 Wall Mounting Instructions (optional to Rack Mounting) The AT&T Business in a Box router may be wall mounted on a ¾ or thicker plywood backing. The unit is too heavy to be mounted to drywall. Use the two (2) rack-mount brackets, eight (8) bracket screws (included) and four (4) 1 ½ wood screws (not included). Complete the following steps: 1) Position the device so that the front panel is facing down and apply the rack-mount brackets with bracket screws to each side as shown in Figure 1. Rack-mount bracket position. 2) Attach the bracket to ¾ or thicker plywood backing using four (4) 1 ½ wood screws as shown in Figure 2. Rack- Mount bracket on plywood backing. Important: Cables will flow down and should be dressed using a wire minder. The unit should be mounted high enough that the technician can see the status lights**. See Figure 3 Installation example. ** It is recommended, but not required that a skilled technician mount the router on the wall. 4

5 Step 2 - Attach Power Cord to Router and Proper Grounding Plug in power cord to router and attach customer provided ground cable Grounding Lug (Customer Provided ground cable) Connect #6 stranded ground to closest earth ground or building bus bar. On/Off Power Switch - Leave powered off until ready for service activation 5 To power strip, UPS or other power source

6 Step 3 - Connect Analog POTS line to Internal Modem Connect customer provided Analog POTS line from wall jack to the internal modem using the provided brown RJ11 cable. RJ11 modem cable Labelled ISE644 6 To wall jack Note: The POTS line may be used in the turn-up of your service as well as by AT&T s Global Customer Service Center.

7 Step 3 - Connect Router to T1 Access Circuit(s) Connect your T1 circuit(s) using the Grey T1 cable(s) to the port(s) labeled Port 1-4. To smart jack(s) T1 Cable(s) labelled ISE642 Note: Up to 4 T1 s may be utilized. If using a single T1 then plug the T1 cable into port 1. A second T1 should be plugged into port 2, third into port 3 and fourth into port 4. 7

8 Step 4 - Connect Router to your Ethernet Devices Connect your Ethernet devices (PC s, printers, servers, etc.) to the integrated Ethernet switch or per instructions in your Site Documentation Package. Customer provide RJ45 LAN Cable(s) Note: If utilizing your own Ethernet switch/firewall behind the AT&T Business in a Box then utilize only Port 2 to interconnect. 8

9 Step 5 - Connect Router to your Analog Key System Connect to your Analog Key System and/or Fax per instructions in your Site Documentation Package. To Key System Customer provide RJ11 Cable(s) connecting green analog ports to your key system or fax 9

10 Step 7 (optional) - Connect Router to Analog POTS for Outbound Site Survivability Connect up to 2 customer provided POTS lines to purple ports for outbound calling survivability. To wall jack Customer provide RJ11 Cable(s) connecting purple analog ports to customer provided POTS line(s) 10

11 AT&T Business in a Box User Guide AT&T Business in a Box includes integrated Wi-Fi capabilities available with your service. A User Guide is available to assist customers with logging into the device using a web browser and configuring to your needs. User Guide Link