AMS 120 EFT Guest Card Terminal & Refund unit
ACCOUNT MANAGEMENT STATIONS Wall mounted kiosk offering Visitor card purchase and refund Card deposit EFT purchase, refund and loading Full statement facilities 8 Touchscreen user interface Maintained from back office Wireless communication Takes card payment 3G enabled
AMS 120 EFT GUEST CARD TERMINAL ONLINE WALL MOUNTED GUEST CARD AND LOADING TERMINAL. > The loader can be filled with 60 cards (approx.) > Customisable card deposit can be set > The application allows a customer to perform any combination of the following functions: > Purchase a visitor card via EFT > Return and refund a visitor card via EFT > Load funds via EFT > View statements > Balance enquiries
AMS 120 DIMENSIONS
MOUNTING BRACKET DIMENSIONS Weight can be 50kg when full. Please note that the key lock is located on the right hand side of the loader and requires 150mm clearance on this side to insert a key and at least 70mm clearance on the left for door opening. If the unit is to be mounted in a recess with the front flush with the wall then you will also need to leave 10mm clearance at the bottom and top to allow the door to open freely. If the unit is required to be in a recess but not elevated from its base surface then the door moulding will be required to protrude past the recess by 60mm and will not sit flush.
SAFETY Whilst lifting the Uniware guest card terminal always use a minimum of two people to hold the weight and a third or fourth person to undertake any maintenance to mount the unit. Also please make sure that you follow your onsite health and safety procedures and that any risk is identified to the relevant parties.
STEP 1 The terminal comes complete with a mounting bracket (pictured), on the bracket you have three 6mm holes which match three holes on the rear of the terminal itself. You will need to mark on the wall the three holes at the required height. (See DDA guideline diagram at the end of this document for recommendations).
STEP 2 There is a cable ridge at the top of the loader where you can run the power cable (kettle lead) and cat5e network cable. Also you can see the three holes that line up with the mounting bracket and the lip where the terminal rests on the bracket. The idea is that you then screw the left and right outer screw holes to secure the bracket on the wall. Additional holes can be drilled by 3 rd parties on the basis these are checked by the equipment owner and that they are checked with Uniware for confirmation and we can advise of any cables \ devices that may be at risk when drilling.
STEP 3 Lift the terminal onto the mounting bracket that is now attached to the wall securely and from inside you should be able to align the centre screw hole allowing you to fix this screw in place through the terminal itself.
AMS 200 SERIES
ACCOUNT MANAGEMENT STATIONS Wall mounted kiosks offering Note & EfT EfT Note & Coin Full statement facilities 19 Touchscreen user interface Maintained from back office Wireless communication Takes card payment 3G enabled
AMS 200 ACCOUNT MANAGEMENT STATION ONLINE WALL MOUNTED CASHLESS ACCOUNT MANAGEMENT STATION AND LOADING TERMINAL. > The loader can be set to accept both notes and coins and displays the starting and finishing account balance once the transaction is completed. > Secure chip & pin \ notes option available. > The loader allows you to have dual readers incorporating biometrics and a chosen card technology. > The application allows a customer to perform any combination of the following functions: > View your live account balance > View & Email Statements > The coin & note version will allow any combination of notes and coins to be loaded to the cashless account > The Chip & Pin \ Note version will allow any combination of notes and customisable values via the integrated secure chip & pin terminal > Multiple currency options available
AMS 200 ACCOUNT MANAGEMENT STATION TECHNICAL > Technical > 240 Volt socket below unit > Ethernet point RJ45 below unit > Dimensions (without bars, if you are requesting the decorative side bars please discuss this with the Uniware sales team) > Height 1000mm > Width 500mm > Depth 265mm > Weight > Aprox 55-60kg
AMS 200 ACCOUNT MANAGEMENT STATION MOUNTING GUIDE AMS 200 SERIES > Please make sure that before undertaking the mounting of this device that the power is disconnected and that you wear the appropriate safety equipment. > Please note the following dimensions are not including the Chrome bars which are not supplied as standard. > Technical > Dimensions > Height 1000mm > Width 500mm > Depth 265mm > Please note that the key locks are located on the right hand side (top \ bottom) of the loader and require 144mm clearance on this side to insert a key.
AMS 200 SERIES MOUNTING GUIDE
AMS 200 SERIES MOUNTING GUIDE
AMS 200 SERIES MOUNTING GUIDE
AMS 200 SERIES MOUNTING GUIDE
AMS 200 SERIES MOUNTING GUIDE If you have purchased a floor stand then please see the below notes and dimensions. You will need a solid concrete base to mount too and we would recommend a fixing like this - http://www.rawlplug.co.uk/en/products /334/335/388/607 M10 is the largest bolt you can get through the base plate, M8 or M10 would be appropriate. We also recommend that the floor stand is covered with a plinth or sits behind a wall and is just used for supporting purposes.
UNIWARE AMS 230 X5
ACCOUNT MANAGEMENT STATIONS Floor standing slim line kiosk offering: Chip & Pin Statements Balance enquiries Full statement facilities 19 Touchscreen user interface Maintained from back office Wireless communication Takes card payment 3G enabled
AMS 230 ACCOUNT MANAGEMENT STATION ONLINE FLOOR STANDING CASHLESS ACCOUNT MANAGEMENT STATION FOR CHIP & PIN LOADING > The loader can be set with varied top up amounts and displays the starting and finishing account balance once the transaction is completed. > Secure chip & pin > The loader allows you to have dual readers incorporating biometrics and a chosen card technology. > The application allows a customer to perform any combination of the following functions: > View your live account balance > View & Email Statements > The Chip & Pin version will allow customisable values via the integrated secure chip & pin terminal
UNIWARE AMS 230 X5 The unit has 2 separate locking housing for components One situated at the back and the other integrated in base For security the unit can be secured to the floor if required The unit requires a 240v power socket and an RJ45 socket
UNIWARE AMS 230 X5 DIMENSIONS W: 1525 mm H: 584 mm D: 518 mm Weight: 52kg
UNIWARE AMS 240 \ 250 X6
ACCOUNT MANAGEMENT STATIONS Floor standing kiosk offering: Note, Chip & Pin and Coins (240) Note & Coin (250) Full statement facilities 19 Touchscreen user interface Maintained from back office Wireless communication Takes card payment and cash 3G enabled
AMS 240 \ 250 ACCOUNT MANAGEMENT STATION ONLINE FLOOR STANDING CASHLESS ACCOUNT MANAGEMENT STATION AND LOADING TERMINAL. > The loader can be set to accept both notes, coins and chip & pin. The unit displays the starting and finishing account balance once the transaction is completed. > Secure chip & pin \ notes and coin options available. > The loader allows you to have dual readers incorporating biometrics and a chosen card technology. > The application allows a customer to perform any combination of the following functions: > View your live account balance > View & Email Statements > The coin & note version will allow any combination of notes and coins to be loaded to the cashless account > The Chip & Pin \ Note and coin version will allow any combination of notes, coins and customisable values via the integrated secure chip & pin terminal > Multiple currency options available
UNIWARE AMS 240 \ 250 X6 The unit has 2 separate locking housing for components One situated at the back and the other integrated in base For security the unit can be secured to the floor if required The unit requires a 240v power socket and an RJ45 socket
UNIWARE AMS 240 \ 250 X6 DIMENSIONS W: 1525 mm H: 609 mm D: 468 mm Weight: 78kg
UNIWARE AMS 240, 250, 260 & 280 SERIES X6
ACCOUNT MANAGEMENT STATIONS Floor standing kiosk offering: Note, Chip & Pin and Coins (240) Note & Coin (250) Note, Coin, Chip & Pin Visitor card issuing station (280) Full statement facilities 19 Touchscreen user interface Maintained from back office Wireless / Ethernet communication Takes card payment and cash
AMS 240 \ 250 \ 280 ACCOUNT MANAGEMENT STATION ONLINE FLOOR STANDING CASHLESS ACCOUNT MANAGEMENT STATION AND LOADING TERMINAL. > The loader can be set to accept both notes, coins and chip & pin. The unit displays the starting and finishing account balance once the transaction is completed. > Secure chip & pin \ notes and coin options available. > The loader allows you to have dual readers incorporating biometrics and a chosen card technology. > The application allows a customer to perform any combination of the following functions: > View your live account balance > View & Email Statements > The coin & note version will allow any combination of notes and coins to be loaded to the cashless account > The Chip & Pin \ Note and coin version will allow any combination of notes, coins and customisable values via the integrated secure chip & pin terminal > The 280 series also holds a card issuer and return hopper. Visitors may set up and load an account with a credit or debit card. Visitor card return includes refund of balance plus deposit > Multiple currency options available
UNIWARE AMS 240 \ 250 \ 280 X6 The unit has 2 separate locking housing for components One situated at the back and the other integrated in base For security the unit can be secured to the floor if required The unit requires a 240v power socket and an RJ45 socket
UNIWARE AMS 240 \ 250 X6 DIMENSIONS W: 1525 mm H: 609 mm D: 468 mm Weight: 78kg Power 240 Volt single outlet Data Single RJ 45