ien yg & ard d tan S ENGLISH

ENGLISH ultpole connectors - T-TYPE enclosures Standard & Hygenc Seres

ULTIPOLE CONNECTORS The company and the product I.L..E. SpA - INDUSTRIA LOBARDA ATERIALE ELETTRICO - has been operatng n lan snce 1938, n partcular n the electrotechncal sector for the manufacture of equpment for ndustral nstallatons. ILE reflects the tradtonal entrepreneural sprt of Lombardy, and has enjoyed contnuous expanson for over half a century. The company has carved an mportant role for tself n the prncpal world markets, also operatng drectly n the countres that have assumed world leadershp n the feld of automaton, ncludng Germany and Japan. In the electrcal connecton sector wth applcatons n ndustral automaton, charactersed by top performance and utmost relablty needs, ILE s today the acknowledged partner of many leadng companes worldwde. CE markng As from 1 January 1997, n order to launch electrcal products on the European market the manufacturer must ensure these bear the relevant CE mark, n lne wth the Low Voltage Drectve 73/23/ EEC * (mplemented n Italy as L. D. 18-10-1977 no. 791) and ts modfcaton 93/68/EEC * (mplemented n Italy as L.D 25-11-1996 no. 626/96, publshed n the supplement to the Gazzetta Uffcale of 14-12-1996). The mark must be vsble on the product or, f ths s not possble, on the packagng, the nstructons for use or on the warranty certfcate. It acts as a declaraton by the manufacturer that the product comples wth all relevant EU drectves regardng ts feld of applcaton. ILE products bear the CE mark on the actual product or ts packagng. Almost all ILE products fall wthn the feld of applcaton of the Low Voltage Drectve. A declaraton of conformty s requred n order to be able to apply the CE mark. Ths declaraton, to whch the market s not drectly enttled, must be made avalable to the controllng authortes (n Italy, the nstry for Industry, Commerce and Handcraft) at all tmes. In t, the manufacturer declares the techncal safety standard(s) followed n the manufacture of the product. These standards must be, n decreasng order of preference: - a European standard (EN prefx) - a European harmonsaton document (HD prefx) - an nternatonal IEC standard - a natonal standard - n the absence of reference standards, the manufacturer s nternal specfcatons guaranteeng complance wth the basc safety requrements of the drectve. Complance wth harmonsed techncal standards (.e. ratfed by CENELEC) also consttutes presumed complance wth the basc safety requrements of the drectves. The CE markng of ILE products results from the declaraton of conformty of the product to harmonsed standards or nternatonal IEC standards. The company s fundamental values are: Product nnovaton, orgnal solutons, excellent prce-qualty rato, acustomer-orented servce, ethcal behavour and respect for the envronment. To promote the contnung mprovement of ts qualtatve results, ILE has always encouraged ts collaborators to work wth maxmum responsblty and partcpaton. The company focuses on a seres of benefts to the user, ncludng research nto the most sutable materals, hgh qualty and safe cablng, a rapd turnaround and readly avalable servces. Through the CE mark, ILE declares full complance, not merely wth the drectve s basc safety requrements, but also wth those nternatonal or natonal EU standards on whch voluntary safety certfcaton markngs are based (e.g. IQ and VDE). In ths way, ILE ntends to gve the CE mark the value of self-certfcaton n terms of safety, gven the loss n legal value of voluntary certfcatons ssued by thrd partes, ratfed by drectve 93/68/EEC *. Notwthstandng the above, practcally all ILE products stll bear voluntary conformty markngs. Ths EC declaraton of conformty becomes null and vod when the assembly of products ncludes one or more components not manufactured by us and wthout EC approval. * Note: The new legal reference for the Low Voltage Drectve s 2006/95/EC whch s the consoldated edton of Drectve 73/23/EEC + Drectve 93/68/EEC. On 29th arch 2014, the Offcal Gazette of the European Unon publshed the new Low Voltage drectve, 2014/35/EU of 26th February 2014, a rewrtten verson of drectve 2006/95/EC, whch wll come nto force on 20th Aprl 2016. ISO 9001 certfcaton: 2008 Desgn, manufacture and dstrbuton of ndustral electrcal equpment (IAF 19, 29a) Certfcate No. 50 100 11133 The nformaton contaned n ths catalogue s not bndng and may be changed wthout notce www.lme.com

ULTIPOLE CONNECTORS T-TYPE SERIES T-TYPE enclosures Standard & Aggressve envronments, Hygenc applcatons T-TYPE standard for standard applcatons HYGIENIC T-TYPE/H for food & beverage HYGIENIC T-TYPE/C for low temperatures Pages 6-15 T-TYPE/W for aggressve envronments Pages 26-53 Pages 16-25 www.lme.com 1

ULTIPOLE CONNECTORS T-TYPE SERIES Internatonal standards T-TYPE General nformaton nternatonal standards general nformaton The T-TYPE enclosures have been successfully tested T-TYPE standard for standard applcatons T-TYPE/W for aggressve envronments HYGIENIC T-TYPE/H producton lnes HYGIENIC T-TYPE/C cold applcatons T-TYPE enclosures have been successfully tested n accordance wth the followng nternatonal standards, guaranteeng ther usage for numerous applcatons: - En 61984: Connectors - Safety requrements and tests. - AnS/Ul 50 (Enclosures for Electrcal Equpment) equvalent to voluntary North Amercan standard NEA 250 (NEA = Natonal Electrcal anufactures Assocaton) and the correspondng Canadan standard CSA C22.2 No. 94 (Specal Purpose Enclosures) for degrees of protecton used n North Amerca and requred by local nstallaton codes (e.g. NFPA 70 Natonal Electrcal Code n the USA, CSA plant standards for Canada). The current type approval was obtaned after passng a number of tests carred out n accordance wth the standard, n partcular: Type 12 (= nema 12) for nternal use, smlar to degree of protecton IP54 accordng to IEC/. (Only standard T-TYPE enclosures). - En 60529: degrees of protecton provded by enclosures (P Code) for ratngs IP65, IP66 and IP69 (where applcable). - En 62262: degrees of protecton provded by enclosures for electrcal equpment aganst external mechancal mpacts (K Code ) for ratngs IK09 (enclosures wth levers), IK10 (enclosures wthout levers). - EC 60068-2-52: Envronmental testng - Part 2-52: Salt spray, cyclc: wth 5% soluton of sodum chlorde (NaCl), soluton Ph from 6.5 to 7.2; EnvronmEnTAl CondTonS: 35 C for 2 hours; 40 C for 168 hours wth 93% relatve humdty; no. of CYClES: 4; TEST PASSEd: mantanng the IP degree of protecton and wth a contact resstance value 150% of the ntal value or 5 mω. - EC 60068-2-6: Envronmental testng - Part 2-6: vbratons (snusodal): wth values 10Hz 500Hz, 0.35 mm ampltude of dsplacement, 50m/s 2 (5g n ), crossover pont 60.1 Hz; no. of CYClES: 10; TEST PASSEd: scannng 3 axes for 2 hours, wth contact resstance value 150% of the ntal value or 5 mω and no mcro-nterrupton ( 1 µs). - EC 60068-2-3: Envronmental testng - Part 2-3: Warm damp: statonary at 40 C, 93% relatve humdty, 504 hours; TEST PASSEd: wth contact resstance value 150% of the ntal value or 5 mω and no dsruptve dscharge (nsulaton resstance > 100 GΩ). - EC 60068-2-30: Envronmental testng - Part 2-30: Cyclc warm humd: 40 C, 95% relatve humdty, 12 hours at ambent temperature; no. of CYClES: 21; TEST PASSEd: wth contact resstance value 150% of the ntal value or 5 mω and no dsruptve dscharge (nsulaton resstance > 100 GΩ). 2

ULTIPOLE CONNECTORS T-TYPE SERIES Applcatons felds T-TYPE General nformaton Applcaton felds NAVAL T AU F SHORE O ROB TICS general nformaton OF S A LT- S P R O AT I O N AY ER S T-TYPE applcaton felds WE R S UPP LI D RA I O C O NTR O LS F SA ETY S YST E B EVE R D& A I C PA N EL G E O FO CTR S E EL E S PO S www.lme.com 3

ULTIPOLE CONNECTORS T-TYPE SERIES Comparson table T-TYPE General nformaton resstance to chemcals comparson table The classfcaton herewth provded s only a generc reference gude n order to enable a frst selecton. It s based on lterature data provded by the supplers of the raw materals used, whch are related to tests carred out on specmens under test condtons whch are not always homogeneous and nvolvng acceleratng technques, therefore not necessarly descrbng real operatonal condtons. The actual behavour of products n the feld may therefore be postvely or negatvely nfluenced by several varable envronmental parameters such as temperature, relatve humdty, smultaneous presence of a pluralty of substances and ther concentraton, exposure tme, dynamc or statc applcaton condton, and so on. The accuracy of transferrng the ndcatons gven heren to the actual condtons of use s therefore merely ndcatve and does not mply any guarantee or responsblty by ILE. general nformaton A Acetone (propanone) x x x x Actve chlorne x x x x Alum l l l l Ammona, 10% aqueous soluton l x l l Ammona, lqud x x l l Ammonum acetate l x l l Ammonum carbonate l l l x Ammonum chlorde l l l x Ammonum ntrate l l l l Ammonum phosphate l l l l Ammonum sulphate l l l l Amyl alcohol o o o x Anlne o o x x Aqua rega (1:3 ntrc acd : hydrochlorc acd) x x x x Asphalt o o o x B Beer l l l l Benzene x o x x Borax o o o o Borc acd l l l l Borc acd, 10% aqueous soluton l l l l Borc water (borc acd 3%) l l l l Butane, gas o o o x Butane, lqud o o o x C Calcum chlorde l l l l Calcum chlorde, 10% aqueous soluton l l l l Calcum chlorde, dluted suspenson l l l l Calcum ntrate l l l l Calcum sulphate l l x l Caustc potash (potassum hydroxde) 10% x l l x Ctrc acd 50% aqueous soluton x l l l Copper sulphate 10% aqueous soluton l l l l Cresol o o x x Cresolc soluton o o x x Cuttng ol o o o x Cyclo-hexane o o o x d Deca-hydro-naphtalene x x x x D-exyl Phtalate l x x x T-TYPE T-TYPE / W T-TYPE / H T-TYPE / C d D-sononyl Phtalate l x x x D-optyl Phtalate l l x x Desel Ol o o o o Dluted Glucose l l l l Dluted Glycerne l l l l Dluted Glycol l l l l Dluted Phenol o o x x Dluted urea l l l l E Ethanol (ethyl alcohol) x x x l Ethyl alcohol l l o l Ethylene-glycol or propylene-glycol l l l l f Fatty acds l l l o Ferrc chlorde, 10% aqueous soluton x x x x Formaln (formaldehyde 40% aqueous soluton) x x l l Frut juces l l l l Fuel ols o o o x G Gaseous ammona o x l l Gaseous propane x l l x Glycerne l l l l Grndng ol o o o x Gypsum (see calcum sulphate) l l x l H Heptane o o o x Hexane o o o x Hydrochlorc acd, <2% aqueous soluton x l l o Hydrogen sulphde o x l x Ink l l l l IR ol 901 l l l l IR ol 902 o l l x IR ol 903 x o o o Isopropyl alcohol o l l l K Ktchen salt, aqueous soluton l l l l T-TYPE T-TYPE / W T-TYPE / H T-TYPE / C legend l : Resstant o : Lmted resstance x : Not resstant 4

ULTIPOLE CONNECTORS T-TYPE SERIES Comparson table T-TYPE General nformaton resstance to chemcals comparson table l Lactc acd l l l l Lnseed ol l l l l Lqud soap x l l l Lubrcatng engne ol o o o x Lubrcatng ol l l l x m ercury l l l l ethanol (methyl alcohol) x x l l ethyl alcohol, dluted 50% o o l l neral based ol l l l l neral ols (un-tasteful) l l l l othballs (naphthalene, paradchlorobenzene) o o x x uratc acd, concentrated x o x x n n-butanol (butyl alcohol) l l l l Naphthalene o l x x Normal (low octane) gasolne (petrol) o o o x o Octane o o o x Olec acd l l l x Oxalc acd l l l l Ozone x o x o P Paraffn ol l l l l Petrol ether o o o o Petroleum l l l l Petroleum sprt (dry cleanng) o o x x Potassum carbonate l l l l Potassum chlorate l l x l Potassum chlorde l l l l Potassum cyande, aqueous soluton l l l l Potassum d-chromate o l l l Potassum odde o l l l Potassum ntrate o x x l Potassum persulphate o l x l Potassum sulphate o l l l S Sea water l l l l Slcon ol l l l x Soap soluton o l l l Sodum bcarbonate (oxde) l l l l Sodum carbonate (washng soda) l l l l Sodum chlorate l l x l Sodum chlorde (ktchen salt) l l l l T-TYPE T-TYPE / W T-TYPE / H T-TYPE / C S Sodum dsulphate, aqueous soluton l l l l Sodum hydroxde (caustc soda) x x l l Sodum hydroxde 12,5% (lscva) o x l l Sodum Hypochlorte x l l l Sodum ntrate l l l x Sodum ntrte o l l x Sodum perborate l l l l Sodum phosphate l l l x Sodum slcate l x x l Sodum sulphate l l l l Sodum sulphde l l l l Sodum Thosulphate (photographc fxer) l l l l Soluton for photographc processng l l l l Starch, aqueous (amylum) l l l l Stearc acd l l l l Succnc acd (butanedoc acd) l l l l Sulphur l l x x Sulphur doxde (sulphurous anhydrde) o x x o Sulphurc acd, 2% aqueous soluton x o o o T Tallow l l l l Tar o o x o Tartarc acd l l l l Toluene x x x x Transformer ol (delectrc) l l l l Trchloroethylene x x x x Trchresyl phosphate l l x x Turpentne essence x o o x U Urne l l l l v Vegetable ol l l l l Vnegar x l l o W Water l l l l Whte alcohol (sopropanol + ethanol) o l l l X Xylene x x x x T-TYPE T-TYPE / W T-TYPE / H T-TYPE / C general nformaton legend l : Resstant o : Lmted resstance x : Not resstant 5

ULTIPOLE CONNECTORS T-TYPE Standard Techncal data T-TYPE Standard for modular and standard nserts T-TYPE Standard T-TYPE nsulatng enclosures for standard applcatons T-TYPE standard IP65,ULTYPE12 for standard applcatons Alongsde the wde range of tradtonal metallc enclosures for ILE multpole connectors, there s now avalable a new seres of enclosures n self-extngushng thermoplastc materal n the most common szes 44.27, 57.27, 77.27 and 104.27. Qualty and money savng are the man features of these enclosures, as an outcome of careful product studes. valuable characterstcs of these new versons of enclosures: - sgnfcant structural soldty and mechancal robustness by vrtue of substantal thckness; - external dmensons of the bulkhead mountng housngs are smlar to those of the correspondng metallc enclosures; hole fxng centres are unchanged; - pre-fastened s for easer nstallaton; - wde space nsde the enclosures for cables, wth mounted connector nserts, smlar to the correspondng hgh constructon versons; - possblty of makng total nsulaton constructons (equvalent to Class II) b ; - absence of powder pant for envronments n whch these are not recommended (e.g. to avod food contamnaton). T-TYPEsTaNdard STAndArd APPlCATonS data SHEETS AT PAGES 8-15 Enclosures n thermoplastc materal, dark grey ral 7012 colour, wth hgh thcknesses provdng structural soldty and durablty. Bult-n polyurethane s. lockng levers n thermoplastc materal colour grey ral 7001. m25, m32 and m40 threaded cable entres. P65 degree of protecton accordng to En 60529; Ul TYPE 12 degree of protecton accordng to AnS/Ul50. Each enclosure carres ts own part number, thread/sze, conformty markngs and UL type ratng. Ambent temperature range: -40 C / +90 C. 6

ULTIPOLE CONNECTORS T-TYPE Standard Techncal data T-TYPE Standard for modular and standard nserts focus on: ➊ Constructon ➍ dmensons By usng the BC-UL mouldng technque and use of IL.BOX materal, these enclosures are structurally sold and mechancally robust, due to ther ncreased thckness. They are partcularly resstant to the man pollutants present n ndustral envronments. The lever enclosure pegs are bult nto the enclosures. The methods for fastenng the connector nserts to the enclosures are made of 3 threaded metal nserts. Wth reference to metal constructon enclosures, whch to comply wth the electrcal nstallaton safety norms, must be earthed va a metal connecton to the groundng termnal of the nserts mounted nsde the enclosures, the new seres of enclosures offers a soluton for total nsulaton constructons (equvalent to class II) where necessary. The thermoplastc materal used s RAL 7012 dark grey colour and UL 94V-2 grade self-extngushng and has passed glow wre testng n accordance wth the IEC (EN) 60695-2-11 at 650 C n complance wth ntended uses. The nternal dmensons allow mountng of all connector nserts n ther relevant szes. The external dmensons of the bulkhead mountng housngs are smlar to those of the correspondng metallc enclosures; hole fxng centres are unchanged. Hoods offer an nner cablng space smlar to that of the hgh constructon models of the correspondng metal enclosures. Other characterstcs are n complance wth the applcable safety standard for electrcal connectors, IEC/EN 61984. ➎ Cable entres The housng and hood cable entres are avalable wth metrc thread, respectvely: m25 or m32 for smaller szes 44.27 and 57.27. m32 or m40 for larger szes 77.27 and 104.27. T-TYPE Standard The surface mountng hgh constructon housngs are suppled wth an open threaded entry and dametrcally opposte a closed threaded entry, whch can be opened by the user, f requred (wth sutable tool). anufactured from nsulatng materal, they do not requre specal renforced nsulaton as the metal versons do, for use wth seres CmE hgher voltage connector nserts (screw-type termnals). ➋ Gaskets T-Type standard sealng s have been produced by means of the FIPFG technology (Formed-In-Place-Foam-Gasket). They have therefore been ncorporated n the base flange on bulkhead mountng housngs for easer nstallaton. T-Type standard: Bult-n polyurethane s T-Type/W: Vton fluoroelastomer s ➌ levers The lockng levers have been produced n self-extngushng thermoplastc materal, grey RAL 7001 colour. The recent standard IEC/EN 61076-7-100 regardng metrc cable entres for multpole electrcal connectors for heavy duty uses, whch standardses some man dmensons for entres and ther related accessores (s, pressure nuts), have been carefully consdered n the product desgn. ➏ markngs Each enclosure carres ts own part number and conformty markngs. ➋ ➊ ➏ ➍ ➎ ➌ 7

T-TYPE nsulatng enclosures sze 44.27 standard applications nserts: CDD... 24 poles + m 59 * CQE... 10 poles + m 80 * CSH... 6 poles + m 88 * CCE... 6 poles + m 94 * CNE, CSE... 6 poles + m 95 * CSS... 6 poles + m 118 * CT, CTE, CTSE *).. 6 poles + m 126 and 130 * IXO... 2 modules 156-195 * CDS... 9 poles + m 6 ** *) only for standard nsulatng verson TCHI housngs wth sngle lever hoods wth 2 pegs nsert centre dstance: 44 x 27 mm T-TYPE Standard descrpton part No. entry part No. entry bulkhead mountng housng wth thermoplastc lever TCHI 06 L surface mountng housng wth thermoplastc lever TAP 06 L25 25 surface mountng housng wth thermoplastc lever TAP 06 L32 32 wth pegs, sde entry TAO 06 L25 25 wth pegs, sde entry TAO 06 L32 32 wth pegs, top entry TAV 06 L25 25 wth pegs, top entry TAV 06 L32 32 panel cut-out for bulkhead mountng housng n mm dmensons n mm dmensons n mm ø 4,5 TCHI 06 L TAO 06 L25 and TAO 06 L32 75 66 72 74 52 70 27 83,5 5 63 32 35 TAP 06 L25 and TAP 06 L32 TAV 06 L25 and TAV 06 L32 75 ( ) 73 Ø 5,5 87 72 70 45 82 57 71,5 6 63 Type 12 ( ) The surface mountng, hgh constructon housngs are suppled wth an open threaded entry ( ) and dametrcally opposte a closed threaded entry whch can be opened by the user f requred (wth sutable tool). IP65 - ambent temperature lmts -40 C / +90 C. dmensons shown are not bndng and may be changed wthout notce 8

T-TYPE nsulatng enclosures sze 44.27 standard applications nserts: CDD... 24 poles + m 59 * CQE... 10 poles + m 80 * CSH... 6 poles + m 88 * CCE... 6 poles + m 94 * CNE, CSE... 6 poles + m 95 * CSS... 6 poles + m 118 * CT, CTE, CTSE *).. 6 poles + m 126 and 130 * IXO... 2 modules 156-195 * CDS... 9 poles + m 6 ** *) only for standard nsulatng verson TCHI hoods wth sngle lever top entry covers nsert centre dstance: 44 x 27 mm descrpton part No. entry part No. wth thermoplastc lever and TAV 06 LG25 25 wth thermoplastc lever and TAV 06 LG32 32 wth pegs wth thermoplastc lever and dmensons n mm TCHC 06 L TCHC 06 LG dmensons n mm T-TYPE Standard TAV 06 LG25 and TAV 06 LG32 TCHC 06 L 75 66 87 63 63 TCHC 06 LG 63 75 66 Type 12 IP65 - ambent temperature lmts -40 C / +90 C. dmensons shown are not bndng and may be changed wthout notce 9

T-TYPE nsulatng enclosures sze 57.27 standard applications nserts: housngs wth double lever hoods wth 4 pegs CDD... 42 poles + m 61 * CQE... 18 poles + m 81 * CSH... 10 poles + m 89 * CCE... 10 poles + m 96 * CNE, CSE... 10 poles + m 97 * CSS... 10 poles + m 119 * CT, CTE, CTSE *) 10 poles + m 127 and 131 * CSE... 3+2 (aux) poles + m 135 * CCE... 3+2 (aux) poles + m 134 * CE... 3+2 (aux) poles + m 135 * CX... 8/24 poles + m 151 * IXO... 3 modules 156-195 * CDS... 18 poles + m 7 ** *) only for standard nsulatng verson TCHI nsert centre dstance: 57 x 27 mm T-TYPE Standard descrpton part No. entry part No. entry bulkhead mountng housng wth thermoplastc levers TCHI 10 surface mountng housng wth thermoplastc levers TAP 10.25 25 surface mountng housng wth thermoplastc levers TAP 10.32 32 wth pegs, sde entry TAO 10.25 25 wth pegs, sde entry TAO 10.32 32 wth pegs, top entry TAV 10.25 25 wth pegs, top entry TAV 10.32 32 panel cut-out for bulkhead mountng housng n mm dmensons n mm dmensons n mm ø 4,5 TCHI 10 TAO 10.25 and TAO 10.32 113 72 74 65 83 27 96,5 5 76 32 35 TAP 10.25 and TAP 10.32 TAV 10.25 and TAV 10.32 113 80 Ø 5,5 87 72 82 45 94 57 6 76 Type 12 The surface mountng, hgh constructon housngs are suppled wth an open threaded entry and dametrcally opposte a closed threaded entry whch can be opened by the user f requred (wth sutable tool). IP65 - ambent temperature lmts -40 C / +90 C. dmensons shown are not bndng and may be changed wthout notce 10

T-TYPE nsulatng enclosures sze 57.27 standard applications nserts: CDD... 42 poles + m 61 * CQE... 18 poles + m 81 * CSH... 10 poles + m 89 * CCE... 10 poles + m 96 * CNE, CSE... 10 poles + m 97 * CSS... 10 poles + m 119 * CT, CTE, CTSE *) 10 poles + m 127 and 131 * CSE... 3+2 (aux) poles + m 135 * CCE... 3+2 (aux) poles + m 134 * CE... 3+2 (aux) poles + m 135 * CX... 8/24 poles + m 151 * IXO... 3 modules 156-195 * CDS... 18 poles + m 7 ** *) only for standard nsulatng verson TCHI hoods wth double lever top entry covers nsert centre dstance: 57 x 27 mm descrpton part No. entry part No. wth thermoplastc levers and TAV 10 G25 25 wth thermoplastc levers and TAV 10 G32 32 wth 4 pegs TCHC 10 wth 2 thermoplastc levers and TCHC 10 G dmensons n mm dmensons n mm T-TYPE Standard TAV 10 G25 and TAV 10 G32 TCHC 10 113 87 76 76 TCHC 10 G 113 76 Type 12 IP65 - ambent temperature lmts -40 C / +90 C. dmensons shown are not bndng and may be changed wthout notce 11

T-TYPE nsulatng enclosures sze 77.27 standard applications nserts: CD... 40 poles + m 49 * CDD... 72 poles + m 62 * CQE... 32 poles + m 82 * CSH... 16 poles + m 90 * CCE... 16 poles + m 98 * CNE, CSE... 16 poles + m 99 * CSS... 16 poles + m 120 * CT, CTE, CTSE *).. 16 poles + m 128 and 132 * CE, CSE 6+2 (aux) poles + m 137 * CCE... 6+2 (aux) poles + m 136 * CP... 6 poles + m 149 * CX... 6/36 and 12/2 poles + m 152-153 * CX... 4/0 and 4/2 poles + m 154 * IXO... 4 modules 156-195 * CDS... 27 poles + m 8 ** CQEE... 40 poles + m 15 *** *) only for standard nsulatng verson TCHI *** refer to Supplement October 2013 catalogue page nsert centre dstance: 77,5 x 27 mm housngs wth double lever hoods wth 4 pegs T-TYPE Standard descrpton part No. entry part No. entry bulkhead mountng housng wth thermoplastc levers TCHI 16 surface mountng housng wth thermoplastc levers TAP 16.32 32 surface mountng housng wth thermoplastc levers TAP 16.40 40 wth pegs, sde entry TAO 16.32 32 wth pegs, sde entry TAO 16.40 40 wth pegs, top entry TAV 16.32 32 wth pegs, top entry TAV 16.40 40 panel cut-out for bulkhead mountng housng n mm dmensons n mm dmensons n mm ø 4,5 TCHI 16 TAO 16.32 and TAO 16.40 133,5 76 80 27 86 103 116,5 5 96,5 TAP 16.32 and TAP 16.40 TAV 16.32 and TAV 16.40 32 35 133,5 80 Ø 5,5 91 76 105 45 117 57 6 96,5 Type 12 The surface mountng, hgh constructon housngs are suppled wth an open threaded entry and dametrcally opposte a closed threaded entry whch can be opened by the user f requred (wth sutable tool). IP65 - ambent temperature lmts -40 C / +90 C. dmensons shown are not bndng and may be changed wthout notce 12

T-TYPE nsulatng enclosures sze 77.27 standard applications nserts: CD... 40 poles + m 49 * CDD... 72 poles + m 62 * CQE... 32 poles + m 82 * CSH... 16 poles + m 90 * CCE... 16 poles + m 98 * CNE, CSE... 16 poles + m 99 * CSS... 16 poles + m 120 * CT, CTE, CTSE *).. 16 poles + m 128 and 132 * CE, CSE 6+2 (aux) poles + m 137 * CCE... 6+2 (aux) poles + m 136 * CP... 6 poles + m 149 * CX... 6/36 and 12/2 poles + m 152-153 * CX... 4/0 and 4/2 poles + m 154 * IXO... 4 modules 156-195 * CDS... 27 poles + m 8 ** CQEE... 40 poles + m 15 *** hoods wth double lever top entry covers *) only for standard nsulatng verson TCHI *** refer to Supplement October 2013 catalogue page nsert centre dstance: 77,5 x 27 mm descrpton part No. entry part No. wth thermoplastc levers and TAV 16 G32 32 wth thermoplastc levers and TAV 16 G40 40 wth 4 pegs TCHC 16 wth 2 thermoplastc levers and dmensons n mm TCHC 16 G dmensons n mm T-TYPE Standard TAV 16 G32 and TAV 16 G40 TCHC 16 133,5 91 96,5 96,5 TCHC 16 G 133,5 96,5 Type 12 IP65 - ambent temperature lmts -40 C / +90 C. dmensons shown are not bndng and may be changed wthout notce 13

T-TYPE nsulatng enclosures sze 104.27 standard applications nserts: CD... 64 poles + m 51 * CDD... 108 poles + m 64 * CQE... poles + m 83 * CSH... 24 poles + m 91 * CCE... 24 poles + m 100 * CNE, CSE... 24 poles + m 101 * CSS... 24 poles + m 121 * CT, CTE, CTSE *) 24 poles + m 129 and 133 * CE, CSE 10+2 (aux) poles + m 139 * CCE... 10+2 (aux) poles + m 138 * CE... 16+2 (aux) poles + m 145 * CCE... 16+2 (aux) poles + m 144 * CX... 4/8 poles + m 155 * IXO... 6 modules 156-195 * CDS... 42 poles + m 9 ** CQEE... 64 poles + m 16 *** *) only for standard nsulatng verson TCHI *** refer to Supplement October 2013 catalogue page nsert centre dstance: 104 x 27 mm housngs wth double lever hoods wth 4 pegs T-TYPE Standard descrpton part No. entry part No. entry bulkhead mountng housng wth thermoplastc levers TCHI 24 surface mountng housng wth thermoplastc levers TAP 24.32 32 surface mountng housng wth thermoplastc levers TAP 24.40 40 wth pegs, sde entry TAO 24.32 32 wth pegs, sde entry TAO 24.40 40 wth pegs, top entry TAV 24.32 32 wth pegs, top entry TAV 24.40 40 panel cut-out for bulkhead mountng housng n mm dmensons n mm dmensons n mm ø 4,5 TCHI 24 TAO 24.32 and TAO 24.40 160 76 80 27 112 130 143,5 5 123 TAP 24.32 and TAP 24.40 TAV 24.32 and TAV 24.40 32 160 35 80 Ø 5,5 91 76 132 45 6 123 144 57 Type 12 The surface mountng, hgh constructon housngs are suppled wth an open threaded entry and dametrcally opposte a closed threaded entry whch can be opened by the user f requred (wth sutable tool). IP65 - ambent temperature lmts -40 C / +90 C. dmensons shown are not bndng and may be changed wthout notce 14

T-TYPE nsulatng enclosures sze 104.27 standard applications nserts: CD... 64 poles + m 51 * CDD... 108 poles + m 64 * CQE... poles + m 83 * CSH... 24 poles + m 91 * CCE... 24 poles + m 100 * CNE, CSE... 24 poles + m 101 * CSS... 24 poles + m 121 * CT, CTE, CTSE *) 24 poles + m 129 and 133 * CE, CSE 10+2 (aux) poles + m 139 * CCE... 10+2 (aux) poles + m 138 * CE... 16+2 (aux) poles + m 145 * CCE... 16+2 (aux) poles + m 144 * CX... 4/8 poles + m 155 * IXO... 6 modules 156-195 * CDS... 42 poles + m 9 ** CQEE... 64 poles + m 16 *** hoods wth double lever top entry covers *) only for standard nsulatng verson TCHI *** refer to Supplement October 2013 catalogue page nsert centre dstance: 104 x 27 mm descrpton part No. entry part No. wth thermoplastc levers and TAV 24 G32 32 wth thermoplastc levers and TAV 24 G40 40 wth 4 pegs TCHC 24 wth 2 thermoplastc levers and dmensons n mm TCHC 24 G dmensons n mm T-TYPE Standard TAV 24 G32 and TAV 24 G40 TCHC 24 160 91 123 123 TCHC 24 G 160 123 Type 12 IP65 - ambent temperature lmts -40 C / +90 C. dmensons shown are not bndng and may be changed wthout notce 15

ULTIPOLE CONNECTORS T-TYPE/W Techncal data T-TYPE / W Aggressve envronments T-TYPE / W - For aggressve envronments Enclosures n thermoplastc materal, dark grey RAL 7012 colour, wth hgh thcknesses provdng structural soldty and durablty. Bult-n VITON fluoroelastomer sealng s. Lockng levers n thermoplastc materal colour grey RAL 7001. 25, 32 and 40 threaded cable entres. IP66 degree of protecton accordng to. Each enclosure carres ts own part number, thread sze and conformty markngs. Ambent temperature range: -40 C / +90 C. NOTE: As the characterzng element of the T-TYPE/W seres s the dfferent sealng materal, hoods and covers wthout sealng s for these seres are the same of T-Type Standard. data sheets AT PAgEs 18-25 T-TYPE/W OFFSHORE NAVAL SALT-SPRAYERS IP66 for aggressve envronments 16 www.lme.com

ULTIPOLE CONNECTORS T-TYPE/W Techncal data T-TYPE / W featurng an orgnal desgn, T-TYPE/W constructon types avalable are: surface mountng housngs wth double entry of whch one closed but threaded hoods wth levers bulkhead mountng housngs hoods wth sde entry hoods wth top entry covers wth pegs (for housngs) wth levers (for hoods) T-TYPE / W - for aggressve envronments double lever, sde and top entry, for other szes 57.27, 77.27, 104.27 double lever, sde and top entry, for other szes 57.27, 77.27, 104.27 sngle lever, sde and top entry, for sze 44.27 sngle lever, sde and top entry, for sze 44.27 17

T-TYPE/ W nsulatng enclosures sze 44.27 aggressive ENvIroNmENTs nserts: CDD... 24 poles + m 59 * CQE... 10 poles + m 80 * CSH... 6 poles + m 88 * CCE... 6 poles + m 94 * CNE, CSE... 6 poles + m 95 * CSS... 6 poles + m 118 * CT, CTE, CTSE *).. 6 poles + m 126 and 130 * IXO... 2 modules 156-195 * CDS... 9 poles + m 6 ** *) only for standard nsulatng verson THIW housngs wth sngle lever hoods wth 2 pegs nsert centre dstance: 44 x 27 mm VITON T-TYPE / W - for aggressve envronments descrpton part No. entry part No. entry bulkhead mountng housng wth thermoplastc levers THIW 06 L surface mountng housng wth thermoplastc levers TAPW 06 L25 25 surface mountng housng wth thermoplastc levers TAPW 06 L32 32 wth pegs, sde entry TAO 06 L25 25 wth pegs, sde entry TAO 06 L32 32 wth pegs, top entry TAV 06 L25 25 wth pegs, top entry TAV 06 L32 32 panel cut-out for bulkhead mountng housng n mm dmensons n mm dmensons n mm ø 4,5 52 70 THIW 06 L 75 83 27 66,5 5 TAO 06 L25 and TAO 06 L32 63 72 74 32 35 TAPW 06 L25 and TAPW 06 L32 TAV 06 L25 and TAV 06 L32 75 ( ) 73 Ø 5,5 87 72 70 45 82 57 71,5 6 63 ( ) The surface mountng, hgh constructon housngs are suppled wth an open threaded entry ( ) and dametrcally opposte a closed threaded entry whch can be opened by the user f requred (wth sutable tool). IP66 - ambent temperature lmts -40 C/+90 C dmensons shown are not bndng and may be changed wthout notce 18

T-TYPE/ W nsulatng enclosures sze 44.27 aggressive ENvIroNmENTs nserts: CDD... 24 poles + m 59 * CQE... 10 poles + m 80 * CSH... 6 poles + m 88 * CCE... 6 poles + m 94 * CNE, CSE... 6 poles + m 95 * CSS... 6 poles + m 118 * CT, CTE, CTSE *).. 6 poles + m 126 and 130 * IXO... 2 modules 156-195 * CDS... 9 poles + m 6 ** *) only for standard nsulatng verson THIW hoods wth sngle lever top entry covers nsert centre dstance: 44 x 27 mm descrpton part No. entry part No. wth thermoplastc lever and TAVW 06 LG25 25 wth thermoplastc lever and TAVW 06 LG32 32 wth pegs wth thermoplastc lever and VITON dmenson n mm TAVW 06 LG25 e TAVW 06 LG32 75 87 66 VITON TCHC 06 L THCW 06 LG dmenson n mm TCHC 06 L 63 T-TYPE / W - for aggressve envronments 63 THCW 06 LG 63 75 66 IP66 - ambent temperature lmts -40 C/+90 C dmensons shown are not bndng and may be changed wthout notce 19

T-TYPE/ W nsulatng enclosures sze 57.27 aggressive ENvIroNmENTs nserts: housngs wth double lever hoods wth 4 pegs CDD... 42 poles + m 61 * CQE... 18 poles + m 81 * CSH... 10 poles + m 89 * CCE... 10 poles + m 96 * CNE, CSE... 10 poles + m 97 * CSS... 10 poles + m 119 * CT, CTE, CTSE *) 10 poles + m 127 and 131 * CSE... 3+2 (aux) poles + m 135 * CCE... 3+2 (aux) poles + m 134 * CE... 3+2 (aux) poles + m 135 * CX... 8/24 poles + m 151 * IXO... 3 modules 156-195 * CDS... 18 poles + m 7 ** *) only for standard nsulatng verson THIW nsert centre dstance: 57 x 27 mm VITON T-TYPE / W - for aggressve envronments descrpton part No. entry part No. entry bulkhead mountng housng wth thermoplastc levers THIW 10 surface mountng housng wth thermoplastc levers TAPW 10.25 25 surface mountng housng wth thermoplastc levers TAPW 10.32 32 wth pegs, sde entry TAO 10.25 25 wth pegs, sde entry TAO 10.32 32 wth pegs, top entry TAV 10.25 25 wth pegs, top entry TAV 10.32 32 panel cut-out for bulkhead mountng housng n mm dmensons n mm dmensons n mm ø 4,5 65 83 THIW 10 TAO 10.25 and TAO 10.32 113 27 72 74 96,5 5 76 32 35 TAPW 10.25 and TAPW 10.32 TAV 10.25 and TAV 10.32 113 80 Ø 5,5 87 72 82 45 94 57 6 76 The surface mountng, hgh constructon housngs are suppled wth an open threaded entry and dametrcally opposte a closed threaded entry whch can be opened by the user f requred (wth sutable tool). IP66 - ambent temperature lmts -40 C/+90 C dmensons shown are not bndng and may be changed wthout notce 20

T-TYPE/ W nsulatng enclosures sze 57.27 aggressive ENvIroNmENTs nserts: CDD... 42 poles + m 61 * CQE... 18 poles + m 81 * CSH... 10 poles + m 89 * CCE... 10 poles + m 96 * CNE, CSE... 10 poles + m 97 * CSS... 10 poles + m 119 * CT, CTE, CTSE *) 10 poles + m 127 and 131 * CSE... 3+2 (aux) poles + m 135 * CCE... 3+2 (aux) poles + m 134 * CE... 3+2 (aux) poles + m 135 * CX... 8/24 poles + m 151 * IXO... 3 modules 156-195 * CDS... 18 poles + m 7 ** *) only for standard nsulatng verson THIW nsert centre dstance: 57 x 27 mm hoods wth double lever top entry VITON covers VITON descrpton part No. entry part No. wth thermoplastc levers and TAVW 10 G25 25 wth thermoplastc levers and TAVW 10 G32 32 wth 4 pegs TCHC 10 wth 2 thermoplastc levers and dmensons n mm THCW 10 G TAVW 10 G25 and TAVW 10 G32 TCHC 10 87 113 dmensons n mm 76 T-TYPE / W - for aggressve envronments 76 THCW 10 G 113 76 IP66 - ambent temperature lmts -40 C/+90 C dmensons shown are not bndng and may be changed wthout notce 21

T-TYPE/ W nsulatng enclosures sze 77.27 aggressive ENvIroNmENTs nserts: CD... 40 poles + m 49 * CDD... 72 poles + m 62 * CQE... 32 poles + m 82 * CSH... 16 poles + m 90 * CCE... 16 poles + m 98 * CNE, CSE... 16 poles + m 99 * CSS... 16 poles + m 120 * CT, CTE, CTSE *).. 16 poles + m 128 and 132 * CE, CSE 6+2 (aux) poles + m 137 * CCE... 6+2 (aux) poles + m 136 * CP... 6 poles + m 149 * CX... 6/36 and 12/2 poles + m 152-153 * CX... 4/0 and 4/2 poles + m 154 * IXO... 4 modules 156-195 * CDS... 27 poles + m 8 ** CQEE... 40 poles + m 15 *** *) only for standard nsulatng verson THIW *** refer to Supplement October 2013 catalogue page nsert centre dstance: 77,5 x 27 mm housngs wth double lever VITON hoods wth 4 pegs T-TYPE / W - for aggressve envronments descrpton part No. entry part No. entry bulkhead mountng housng wth thermoplastc levers THIW 16 surface mountng housng wth thermoplastc levers TAPW 16.32 32 surface mountng housng wth thermoplastc levers TAPW 16.40 40 wth pegs, sde entry TAO 16.32 32 wth pegs, sde entry TAO 16.40 40 wth pegs, top entry TAV 16.32 32 wth pegs, top entry TAV 16.40 40 panel cut-out for bulkhead mountng housng n mm dmensons n mm dmensons n mm ø 4,5 THIW 16 TAO 16.32 and TAO 16.40 133,5 76 80 27 86 103 116,5 5 96,5 TAPW 16.32 and TAPW 16.40 TAV 16.32 and TAV 16.40 32 35 133,5 80 Ø 5,5 91 76 105 45 117 57 6 96,5 The surface mountng, hgh constructon housngs are suppled wth an open threaded entry and dametrcally opposte a closed threaded entry whch can be opened by the user f requred (wth sutable tool). IP66 - ambent temperature lmts -40 C/+90 C dmensons shown are not bndng and may be changed wthout notce 22

T-TYPE/ W nsulatng enclosures sze 77.27 aggressive ENvIroNmENTs nserts: CD... 40 poles + m 49 * CDD... 72 poles + m 62 * CQE... 32 poles + m 82 * CSH... 16 poles + m 90 * CCE... 16 poles + m 98 * CNE, CSE... 16 poles + m 99 * CSS... 16 poles + m 120 * CT, CTE, CTSE *).. 16 poles + m 128 and 132 * CE, CSE 6+2 (aux) poles + m 137 * CCE... 6+2 (aux) poles + m 136 * CP... 6 poles + m 149 * CX... 6/36 and 12/2 poles + m 152-153 * CX... 4/0 and 4/2 poles + m 154 * IXO... 4 modules 156-195 * CDS... 27 poles + m 8 ** CQEE... 40 poles + m 15 *** *) only for standard nsulatng verson THIW *** refer to Supplement October 2013 catalogue page nsert centre dstance: 77,5 x 27 mm hoods wth double lever top entry covers descrpton part No. entry part No. wth thermoplastc levers and TAVW 16 G32 32 wth thermoplastc levers and TAVW 16 G40 40 wth 4 pegs TCHC 16 wth 2 thermoplastc levers and THCW 16 G TAVW 16 G32 and TAVW 16 G40 TCHC 16 91 VITON dmensons n mm 133,5 VITON dmensons n mm 96,5 T-TYPE / W - for aggressve envronments 96,5 THCW 16 G 133,5 96,5 IP66 - ambent temperature lmts -40 C/+90 C dmensons shown are not bndng and may be changed wthout notce 23

T-TYPE/ W nsulatng enclosures sze 104.27 aggressive ENvIroNmENTs nserts: CD... 64 poles + m 51 * CDD... 108 poles + m 64 * CQE... poles + m 83 * CSH... 24 poles + m 91 * CCE... 24 poles + m 100 * CNE, CSE... 24 poles + m 101 * CSS... 24 poles + m 121 * CT, CTE, CTSE *) 24 poles + m 129 and 133 * CE, CSE 10+2 (aux) poles + m 139 * CCE... 10+2 (aux) poles + m 138 * CE... 16+2 (aux) poles + m 145 * CCE... 16+2 (aux) poles + m 144 * CX... 4/8 poles + m 155 * IXO... 6 modules 156-195 * CDS... 42 poles + m 9 ** CQEE... 64 poles + m 16 *** housngs wth double lever hoods wth 4 pegs *) only for standard nsulatng verson THIW *** refer to Supplement October 2013 catalogue page nsert centre dstance: 104 x 27 mm VITON T-TYPE / W - for aggressve envronments descrpton part No. entry part No. entry bulkhead mountng housng wth thermoplastc levers THIW 24 surface mountng housng wth thermoplastc levers TAPW 24.32 32 surface mountng housng wth thermoplastc levers TAPW 24.40 40 wth pegs, sde entry TAO 24.32 32 wth pegs, sde entry TAO 24.40 40 wth pegs, top entry TAV 24.32 32 wth pegs, top entry TAV 24.40 40 panel cut-out for bulkhead mountng housng n mm dmensons n mm dmensons n mm ø 4,5 THIW 24 TAO 24.32 and TAO 24.40 160 76 80 27 112 130 143,5 5 123 TAPW 24.32 and TAPW 24.40 TAV 24.32 and TAV 24.40 32 160 35 80 Ø 5,5 91 76 132 45 6 123 144 57 The surface mountng, hgh constructon housngs are suppled wth an open threaded entry and dametrcally opposte a closed threaded entry whch can be opened by the user f requred (wth sutable tool). IP66 - ambent temperature lmts -40 C/+90 C dmensons shown are not bndng and may be changed wthout notce 24

T-TYPE/ W nsulatng enclosures sze 104.27 aggressive ENvIroNmENTs nserts: CD... 64 poles + m 51 * CDD... 108 poles + m 64 * CQE... poles + m 83 * CSH... 24 poles + m 91 * CCE... 24 poles + m 100 * CNE, CSE... 24 poles + m 101 * CSS... 24 poles + m 121 * CT, CTE, CTSE *) 24 poles + m 129 and 133 * CE, CSE 10+2 (aux) poles + m 139 * CCE... 10+2 (aux) poles + m 138 * CE... 16+2 (aux) poles + m 145 * CCE... 16+2 (aux) poles + m 144 * CX... 4/8 poles + m 155 * IXO... 6 modules 156-195 * CDS... 42 poles + m 9 ** CQEE... 64 poles + m 16 *** hoods wth double lever top entry covers *) only for standard nsulatng verson THIW *** refer to Supplement October 2013 catalogue page nsert centre dstance: 104 x 27 mm VITON VITON descrpton part No. entry part No. wth thermoplastc levers and TAVW 24 G32 32 wth thermoplastc levers and TAVW 24 G40 40 wth 4 pegs TCHC 24 wth 2 thermoplastc levers and dmensons n mm THCW 24 G TAVW 24 G32 and TAVW 24 G40 TCHC 24 91 160 dmensons n mm 123 T-TYPE / W - for aggressve envronments 123 THCW 24 G 160 123 IP66 - ambent temperature lmts -40 C/+90 C dmensons shown are not bndng and may be changed wthout notce 25

ULTIPOLE CONNECTORS HYGIENIC Applcaton felds HYGEnC for food and beverage D A I RY E RI N D BAK SA ER Y PR OD PA S T PA S TA HYGIENIC E W INE applcaton felds D VEGETAB LE D F R U I T J UI C AN D SP IR I TS food & beverage applcatons A E NN HYGEnC U CTS S AN C PE T FOO D E AT A N D P OU R LT Y www.lme.com 26

ULTIPOLE CONNECTORS HYGIENIC Food & beverage requrements HYGEnC resstance of materals to detergents/dsnfectants used n the food ndustry The new lme T-Type/H and T-Type/C enclosure materals have been selected to guarantee compatblty wth the prncpal alkalne or acd detergents and dsnfectants used n the food ndustry. In partcular, T-Type/H and T-Type/C seres enclosures have been tested accordng to protocol f&e/p3-e n. 40-1 by Ecolab, leadng multnatonal n the detergent sector, to verfy ther compatblty wth the followng cleanng fluds: Acd foamng detergents: P3-topax 52, P3-topmaxx 520 and P3-topax 56. Alkalne foamng detergents: P3-topax 19 and Ecofoam Basc. Strong alkalne foamng detergents: P3-topax 36 and P3-topax 30. Alkalne-chlorde foamng detergents-dsnfectants: P3-topax 66, Ecofoam Cl and P3-topax m95. non-foamng peracetc based dsnfectants: P3-oxona actve, P3-topactve okto and P3-topactve des. neutral dsnfectants: P3-topax 990 and P3-topax 91. EColAB f&e/p3-e n. 40-1 Test Protocol SEE declaraton of ComPATBlTY AT PAGES 28-29 Full mmerson of parts n detergent/dsnfectant solutons. Water hardness of 200ppm CaCO 3 Concentratons tested 30% hgher than those normally recommended 28 days total tme at 20 C (equvalent to the contact tme that occurs n 6 years of daly cleanng) Test soluton renewed every 3-4 days for oxdng products Test results evaluaton: ISO 40068-1 (esthetc appearance) and mass loss Cleanablty and degrees of protecton used n the food ndustry HYGEnC T-Type/H and T-Type/C seres enclosures have been desgned to facltate cleanng of surfaces that could potentally come nto contact wth food. For ths purpose T-Type/H and T-Type/C seres enclosures have P66 and P69 degrees of protecton as per EC 60529 Edton 2.2 (2013-08) to allow jet washng, as typcal aspect of the food ndustry. The sutablty of our products for the cleanablty requrements stated by achnery Drectve 2006/42/EC for both Splash and Food Area zones (EN 1672-2 and EN ISO 14159) depends on the specfc nstallaton of lme products on the machne and must be evaluated by the machne manufacturer (see page 31, Table 1, Applcatons Zones). In addton to the Hygenc verson, alumnum cases are also avalable wth degrees of protecton up to IP68 (check applcablty). HYGIENIC food & beverage applcatons IP66 IP69 27

ULTIPOLE CONNECTORS HYGIENIC Food & beverage requrements declaraton of compatblty - By courtesy of EColAB s.r.l. HYGEnC 28

ULTIPOLE CONNECTORS HYGIENIC Food & beverage requrements declaraton of compatblty - By courtesy of EColAB s.r.l. HYGEnC 29

ULTIPOLE CONNECTORS HYGIENIC Food & beverage requrements HYGEnC requrements on materals n contact or that may come nto contact wth food products HYGEnC aterals have been selected to satsfy the requrements of EHEdG Gudelne n 32 aterals of constructon for food equpment n contact wth food and pont 2.1.1, letter a) n Annex I of the machnery drectve 2006/42/EC. Paragraph 91 of the Gude to the applcaton of machnery drectve 2006/42/EC specfes that the reference at Annex I, pont 2.1.1, letter a) of the drectve must be consdered as a reference to EC regulaton n. 1935/2004 and drectve 2002/72/EC. EU commsson regulaton n. 10/2011 dated 14 January 2011, concernng plastc materal and objects desgned for contact wth food products, s a specfc measure as provded for by artcle 5, paragraph 1 of the above-mentoned EC regulaton n. 1935/2004. It defnes specfc regulatons for plastc materals and objects n order to guarantee ther use n safe condtons and supersedes commsson drectve 2002/72/EC dated 6 August 2002 on plastc materals and objects desgned for contact wth food products. Art. 2, secton 2 of the abovementoned EU regulaton n. 10/2011 specfes that rubber and slcone do not fall wthn the feld of applcaton of the regulaton. EU regulaton n. 10/2011 provdes for the use of materals n postve lsts of technologcal monomers, addtves and adjuvants and the passng of global and specfc mgraton tests n food smulants. ILE T-Type/C seres enclosure materals have been selected accordng to EU n. 10/2011 regulaton requrements and each component has been tested accordng to EU regulaton n. 10/2011 and EC regulaton n. 1935/2004. Furthermore, T-Type/C seres materals have been formulated accordng to fda Gudelne 21 Cfr 177.2600 and T-Type enclosures and levers materals complyng wth fda, 21 Cfr, 177.1520 (a)(3)()(c)(1), (b) and (c)3.1a. HYGIENIC food & beverage applcatons 30 www.lme.com

ULTIPOLE CONNECTORS HYGIENIC Food & beverage requrements HYGEnC rsk Assessment and Crtcal Control Ponts n the food ndustry Companes that work n the food sector must mplement HACCP,.e. Hazard Analyss and Crtcal Control Ponts system (EC regulaton 852/2004 on food product hygene n force snce 01/01/2006) and can voluntarly apply for varous certfcates (ISO 22000, BRC, ISF, etc.). All those nvolved n prmary food producton (harvestng, mlkng, breedng), ts preparaton, transformaton, manufacturng, packagng, storage, transport, dstrbuton, handlng, sales or supply, ncludng consumer caterng, are requred to mplement an HACCP system,.e. a seres of procedures amed at preventng food contamnaton hazards. HACCP s based on montorng food processng ponts where bologcal, chemcal or physcal contamnaton hazards may arse. In 2006, HACCP was made mandatory for companes that deal wth the food for anmals (producton of raw materals, mxtures and addtves). A company requred to mplement HACCP can ntally be dvded nto three zones from the pont of vew of food rsk. The choce of the zone n whch the wrng and connectors are nstalled depends on the rsk assessment the manufacturer must conduct as per machnery drectve 2006/42/EC whch, n chapter 2.1, sets out the addtonal requrements for the food ndustry. Table 1. Accordng to En 1672-2:2009 - food processng machnery - Basc concepts - Part 2: Hygene requrements Applcaton Zones no food Area: Zone where there s no contact rsk wth food. Zone requrements No addtonal requrement for the food ndustry. Usable Products Enclosures seres T-Type, T-Type/W, C-Type, BIG, IP68, C7 IP67, W-Type, EC, COB, HYGEnC Splash Area: Zone where components may come nto contact wth food but there s no rsk that the food that came nto contact wth the components n ths area returns to the producton cycle. In ths zone, components also come nto contact wth cleanng agents used n the food ndustry and must therefore be cleanable and resstant to the washng process (see Resstance of materals to detergents/dsnfectants used n the food ndustry and Cleanablty and degrees of protecton used n the food ndustry, see page 27). New Hygenc verson enclosures seres T-Type/H and T-Type/C. food Area: Zone where components may come nto contact wth food, wth the rsk that the food that came nto contact wth the components n ths area returns to the producton cycle. In ths zone, n addton to complyng wth the cleanablty and washng requrements, the components are also subject to a seres of more strngent requrements amed at makng neglgble the rsk of food contamnaton n the process (see paragraph Requrements on materals n contact or that can come nto contact wth food products, see page 30). for more nformaton about T-Type/C n specal verson, please contact our offces. 31

ULTIPOLE CONNECTORS HYGIENIC Food & beverage requrements food & Beverage Hygene requrements low Temperatures Splash Area Applcaton Zones Splash Area Zone requrements HYGEnC T-TYPE / C Seres HYGEnC / C Usable Products Range of temperature: -50 C / +70 C 32

ULTIPOLE CONNECTORS HYGIENIC Food & beverage requrements Producton lnes Splash Area no food Area Splash Area Zone where components may come nto contact wth food but there s no rsk that the food that came nto contact wth the components n ths area returns to the producton cycle. no food Area Zone where there s no contact rsk wth food. HYGEnC T-TYPE / H Seres STAndArd Seres HYGEnC / H T-TYPE Std. & W Insulatng enclosures wth resstance of materals to detergents / dsnfectants Insulatng enclosures, up to 200A nserts www.lme.com 33

ULTIPOLE CONNECTORS HYGIENIC Techncal data HYGEnC T-TYPE/H & T-TYPE/C The evoluton of T-Type nsulatng enclosures meets food and beverage requrements HYGIENIC food & beverage applcatons IP66 IP69 HYGEnC 34 The new Hygenc mult-pole connector enclosures verson (seres T-Type/H and T-Type/C) has been desgned for nstallaton on food ndustry machnes and systems. For ths purpose, the followng mprovements to the T-Type seres have been made n order to satsfy the requrements lad down by chapter 2.1 of machnery drectve 2006/42/EC for the machnes on whch they are nstalled: - materal cleanablty and resstance to the cleanng and santsng agents normally used n the food ndustry; - materals n terms of the requrements for accdental contact wth food products. The T-Type/H and T-Type/C seres enclosures ft dfferent sealng s. For T-Type/H seres enclosures, the sealng s n HNBR rubber, a materal wth excellent resstance to both acdc and alkalne detergents as well as any anmal and vegetable fats t could come nto contact wth n food ndustry applcatons. For T-Type/C seres enclosures, the sealng s made by slcone rubber, a materal wth good resstance to acdc and alkalne detergents as well as anmal and vegetable fats. It s also charactersed by ts mproved resstance to low temperatures (seres sutable for uses as low as -50 C), condtons that can arse n food ndustres that use the cold chan. A dedcated varant of ths new Hygenc verson may be used where a hgh rsk of accdental contact wth food s occurng durng producton (see page 33, Table 1, Applcaton Zones, Food Area). For more nformaton about ths possble specal verson, please contact our Offces. In accordance wth the requrements set forth n EHEdG Gudelne n. 32 aterals of constructon for food equpment n contact wth food (EHEDG = European Hygenc Engneerng & Desgn Group), the closng levers and sealng s are coloured blue to easly dentfy any accdental contamnatons n food products and to facltate the vsual dentfcaton of ther complete cleanlness. www.lme.com

ULTIPOLE CONNECTORS HYGIENIC Techncal data HYGEnC T-TYPE/H & T-TYPE/C T-TYPE/H ProdUCTon lnes APPlCATonS data SHEETS AT PAGES 38-45 Enclosures n thermoplastc materal, dark grey ral 7012 colour, wth hgh thcknesses provdng structural soldty and durablty. Sealng s made by HnBr rubber formulated n accordance wth fda Gudelne 21 Cfr 177.2600. levers n thermoplastc materal, blue ral 5015 colour. m25, m32 and m40 threaded cable entres. P66 and P69 degree of protecton accordng to En 60529. Each enclosure carres ts own part number, thread/sze and conformty markngs. Ambent temperature range: -40 C / +70 C. T-TYPE/C low TEmPErATUrE APPlCATonS data SHEETS AT PAGES -53 HYGEnC The Hygenc T-Type/C Seres enclosures have been specfcally desgned for food and beverage ambent temperature as low as -50 C (range: -50 C / +70 C). Enclosures n thermoplastc materal, dark grey ral 7012 colour, wth hgh thcknesses provdng structural soldty and durablty. Ths verson dffers from the Hygenc T-Type/H one for the sealng s made by n accordance wth fda Gudelne 21 Cfr 177.2600. ILE T-Type/C seres enclosure materals have been selected accordng to EU n. 10/2011 regulaton requrements and each component has been tested accordng to EU regulaton n. 10/2011 and EC regulaton n. 1935/2004. note: As the characterzng elements of the Hygenc Seres are the dfferent sealng materal and the dfferent lockng lever, hoods and covers wthout sealng s and lockng levers are the same of seres T-Type Standard. 35

ULTIPOLE CONNECTORS HYGIENIC Techncal data HYGEnC T-TYPE/H & T-TYPE/C focus on: ➊ Constructon ➎ Cable entres HYGEnC By usng the BC-UL mouldng technque together wth the use of IL.BOX materal, these enclosures are structurally sold and mechancally robust, due to ther ncreased thckness. They are partcularly resstant to the man pollutants present n ndustral envronments. The lever enclosure pegs are bult nto the enclosures. The methods for fastenng the connectors to the enclosures are made by 3 threaded metal nserts. Wth reference to metal constructon, whch to comply wth electrcal nstallaton safety norms, must be earthed va a metal connecton to the protectve earth termnal of the connector nserts nsde the enclosure, the new seres of enclosures offers a soluton for total nsulaton constructons b (equvalent to class ) where necessary. The thermoplastc materal used s RAL 7012 dark grey colour and has passed glow wre testng n accordance wth the IEC (EN) 60695-2-11 at 650 C n complance wth ntended uses. ➋ Gaskets Gaskets have been produced n HnBr rubber or SlConE rubber and have been ncorporated n the base flange on bulkhead mountng housngs for easer nstallaton. The housng and hood cable entres are avalable wth metrc thread, respectvely: m25 or m32 for smaller szes 44.27 and 57.27. m32 or m40 for larger szes 77.27 and 104.27. The surface mountng, hgh constructon housngs are suppled wth an open threaded entry and dametrcally opposte a closed threaded entry whch can be opened by the user f requred (wth sutable tool). The recent standard EC/En 61076-7-100 regardng metrc cable entres for multpole electrcal connectors for heavy duty uses, whch standardses some man dmensons for entres and ther related accessores (s, pressure nuts), have been carefully consdered n the product desgn. ➏ markngs Each enclosure carres ts own part number and conformty markngs. ➌ levers The lockng levers have been produced n self-extngushng thermoplastc materal, blue RAL 5015 colour. ➊ ➍ dmensons The nternal dmensons allow mountng of all connector nserts n ther relevant szes. The external dmensons of the bulkhead mountng housngs are smlar to those of the correspondng metallc enclosures; hole fxng centres are unchanged. Hoods offer an nner cablng space smlar to that of the hgh constructon models of the correspondng metal enclosures. Other characterstcs are n complance wth the applcable safety standard for electrcal connectors, EC/En 61984. ➏ ➋ ➎ ➌ ➍ 36

ULTIPOLE CONNECTORS HYGIENIC Techncal data HYGEnC featurng an orgnal desgn, T-TYPE/H & T-TYPE/C constructon types avalable are: surface mountng housngs wth double entry of whch one closed but threaded hoods wth levers bulkhead mountng housngs hoods wth sde entry hoods wth top entry covers wth pegs (for housngs) wth levers (for hoods) HYGEnC double lever, sde and top entry, for other szes 57.27, 77.27, 104.27 double lever, sde and top entry, for other szes 57.27, 77.27, 104.27 sngle lever, sde and top entry, for sze 44.27 sngle lever, sde and top entry, for sze 44.27 37

T-TYPE/ H producton lnes enclosures sze 44.27 HYGIENICsErIEs nserts: CDD... 24 poles + m 59 * CQE... 10 poles + m 80 * CSH... 6 poles + m 88 * CCE... 6 poles + m 94 * CNE, CSE... 6 poles + m 95 * CSS... 6 poles + m 118 * CT, CTE, CTSE *).. 6 poles + m 126 and 130 * IXO... 2 modules 156-195 * CDS... 9 poles + m 6 ** housngs wth sngle lever hoods wth 2 pegs *) only for standard nsulatng verson THIH nsert centre dstance: 44 x 27 mm HNBR descrpton part No. entry part No. entry bulkhead mountng housng wth thermoplastc lever THIH 06 L surface mountng housng wth thermoplastc lever TAPH 06 L25 25 surface mountng housng wth thermoplastc lever TAPH 06 L32 32 wth pegs, sde entry TAO 06 L25 25 wth pegs, sde entry TAO 06 L32 32 wth pegs, sde entry TAV 06 L25 25 wth pegs, sde entry TAV 06 L32 32 panel cut-out for bulkhead mountng housng n mm dmensons n mm dmensons n mm ø 4,5 THIH 06 L TAO 06 L25 e TAO 06 L32 75 66 72 74 52 70 27 HYGEnC T-TYPE/H 32 35 5 83,5 TAPH 06 L25 and TAPH 06 L32 75 63 TAV 06 L25 and TAV 06 L32 ( ) 73 Ø 5,5 87 72 70 45 82 57 71,5 6 63 ( ) The surface mountng, hgh constructon housngs are suppled wth an open threaded entry ( ) and dametrcally opposte a closed threaded entry whch can be opened by the user f requred (wth sutable tool). IP66 IP69 - ambent temperature lmts -40 C / +70 C dmensons shown are not bndng and may be changed wthout notce 38

T-TYPE/ H producton lnes enclosures sze 44.27 HYGIENICsErIEs nserts: CDD... 24 poles + m 59 * CQE... 10 poles + m 80 * CSH... 6 poles + m 88 * CCE... 6 poles + m 94 * CNE, CSE... 6 poles + m 95 * CSS... 6 poles + m 118 * CT, CTE, CTSE *).. 6 poles + m 126 and 130 * IXO... 2 modules 156-195 * CDS... 9 poles + m 6 ** hoods wth sngle lever top entry covers *) only for standard nsulatng verson THIH nsert centre dstance: 44 x 27 mm HNBR HNBR descrpton part No. entry part No. entry wth thermoplastc lever and TAVH 06 LG25 25 wth thermoplastc lever and TAVH 06 LG32 32 wth pegs wth thermoplastc lever and dmensons n mm TAVH 06 LG25 and TAVH 06 LG32 TCHC 06 L THCH 06 LG dmensons n mm TCHC 06 L 75 66 87 63 63 THCH 06 LG 63 75 66 HYGEnC T-TYPE/H IP66 IP69 - ambent temperature lmts -40 C / +70 C dmensons shown are not bndng and may be changed wthout notce 39

T-TYPE/ H producton lnes enclosures sze 57.27 HYGIENICsErIEs nserts: housngs wth double lever hoods wth 4 pegs CDD... 42 poles + m 61 * CQE... 18 poles + m 81 * CSH... 10 poles + m 89 * CCE... 10 poles + m 96 * CNE, CSE... 10 poles + m 97 * CSS... 10 poles + m 119 * CT, CTE, CTSE *) 10 poles + m 127 and 131 * CSE... 3+2 (aux) poles + m 135 * CCE... 3+2 (aux) poles + m 134 * CE... 3+2 (aux) poles + m 135 * CX... 8/24 poles + m 151 * IXO... 3 modules 156-195 * CDS... 18 poles + m 7 ** *) only for standard nsulatng verson THIH nsert centre dstance: 57 x 27 mm HNBR descrpton part No. entry part No. entry bulkhead mountng housng wth thermoplastc levers THIH 10 surface mountng housng wth thermoplastc levers TAPH 10.25 25 surface mountng housng wth thermoplastc levers TAPH 10.32 32 wth pegs, sde entry TAO 10.25 25 wth pegs, sde entry TAO 10.32 32 wth pegs, top entry TAV 10.25 25 wth pegs, top entry TAV 10.32 32 panel cut-out for bulkhead mountng housng n mm dmensons n mm dmensons n mm ø 4,5 THIH 10 TAO 10.25 and TAO 10.32 65 83 113 27 72 74 HYGEnC T-TYPE/H 32 35 5 96,5 76 TAPH 10.25 and TAPH 10.32 TAV 10.25 and TAV 10.32 113 80 Ø 5,5 87 72 82 45 94 57 6 76 The surface mountng, hgh constructon housngs are suppled wth an open threaded entry and dametrcally opposte a closed threaded entry whch can be opened by the user f requred (wth sutable tool). IP66 IP69 - ambent temperature lmts -40 C / +70 C dmensons shown are not bndng and may be changed wthout notce 40

T-TYPE/ H producton lnes enclosures sze 57.27 HYGIENICsErIEs nserts: CDD... 42 poles + m 61 * CQE... 18 poles + m 81 * CSH... 10 poles + m 89 * CCE... 10 poles + m 96 * CNE, CSE... 10 poles + m 97 * CSS... 10 poles + m 119 * CT, CTE, CTSE *) 10 poles + m 127 and 131 * CSE... 3+2 (aux) poles + m 135 * CCE... 3+2 (aux) poles + m 134 * CE... 3+2 (aux) poles + m 135 * CX... 8/24 poles + m 151 * IXO... 3 modules 156-195 * CDS... 18 poles + m 7 ** *) only for standard nsulatng verson THIH nsert centre dstance: 57 x 27 mm hoods wth double lever top entry HNBR covers HNBR descrpton part No. entry part No. wth thermoplastc levers and TAVH 10 G25 25 wth thermoplastc levers and TAVH 10 G32 32 wth 4 pegs TCHC 10 wth 2 thermoplastc levers and dmensons n mm THCH 10 G dmensons n mm TAVH 10 G25 and TAVH 10 G32 TCHC 10 113 87 76 76 THCH 10 G 113 HYGEnC T-TYPE/H 76 IP66 IP69 - ambent temperature lmts -40 C / +70 C dmensons shown are not bndng and may be changed wthout notce 41

T-TYPE/ H producton lnes enclosures sze 77.27 HYGIENICsErIEs nserts: CD... 40 poles + m 49 * CDD... 72 poles + m 62 * CQE... 32 poles + m 82 * CSH... 16 poles + m 90 * CCE... 16 poles + m 98 * CNE, CSE... 16 poles + m 99 * CSS... 16 poles + m 120 * CT, CTE, CTSE *).. 16 poles + m 128 and 132 * CE, CSE 6+2 (aux) poles + m 137 * CCE... 6+2 (aux) poles + m 136 * CP... 6 poles + m 149 * CX... 6/36 and 12/2 poles + m 152-153 * CX... 4/0 and 4/2 poles + m 154 * IXO... 4 modules 156-195 * CDS... 27 poles + m 8 ** CQEE... 40 poles + m 15 *** *) only for standard nsulatng verson THIH *** refer to Supplement October 2013 catalogue page nsert centre dstance: 77,5 x 27 mm housngs wth double lever HNBR hoods wth 4 pegs descrpton part No. entry part No. entry bulkhead mountng housng wth thermoplastc levers THIH 16 surface mountng housng wth thermoplastc levers TAPH 16.32 32 surface mountng housng wth thermoplastc levers TAPH 16.40 40 wth pegs, sde entry TAO 16.32 32 wth pegs, sde entry TAO 16.40 40 wth pegs, top entry TAV 16.32 32 wth pegs, top entry TAV 16.40 40 panel cut-out for bulkhead mountng housng n mm dmensons n mm dmensons n mm ø 4,5 THIH 16 TAO 16.32 and TAO 16.40 133,5 76 80 HYGEnC T-TYPE/H 32 35 86 103 27 5 116,5 96,5 TAPH 16.32 and TAPH 16.40 TAV 16.32 and TAV 16.40 133,5 80 Ø 5,5 91 76 105 45 117 57 6 96,5 The surface mountng, hgh constructon housngs are suppled wth an open threaded entry and dametrcally opposte a closed threaded entry whch can be opened by the user f requred (wth sutable tool). IP66 IP69 - ambent temperature lmts -40 C / +70 C dmensons shown are not bndng and may be changed wthout notce 42

T-TYPE/ H producton lnes enclosures sze 77.27 HYGIENICsErIEs nserts: CD... 40 poles + m 49 * CDD... 72 poles + m 62 * CQE... 32 poles + m 82 * CSH... 16 poles + m 90 * CCE... 16 poles + m 98 * CNE, CSE... 16 poles + m 99 * CSS... 16 poles + m 120 * CT, CTE, CTSE *).. 16 poles + m 128 and 132 * CE, CSE 6+2 (aux) poles + m 137 * CCE... 6+2 (aux) poles + m 136 * CP... 6 poles + m 149 * CX... 6/36 and 12/2 poles + m 152-153 * CX... 4/0 and 4/2 poles + m 154 * IXO... 4 modules 156-195 * CDS... 27 poles + m 8 ** CQEE... 40 poles + m 15 *** *) only for standard nsulatng verson THIH *** refer to Supplement October 2013 catalogue page nsert centre dstance: 77,5 x 27 mm hoods wth double lever top entry covers descrpton part No. entry part No. wth thermoplastc levers and TAVH 16 G32 32 wth thermoplastc levers and TAVH 16 G40 40 wth 4 pegs TCHC 16 wth 2 thermoplastc levers and HNBR dmensons n mm HNBR THCH 16 G dmensons n mm TAVH 16 G32 and TAVH 16 G40 TCHC 16 133,5 91 96,5 96,5 THCH 16 G 133,5 HYGEnC T-TYPE/H 96,5 IP66 IP69 - ambent temperature lmts -40 C / +70 C dmensons shown are not bndng and may be changed wthout notce 43

T-TYPE/ H producton lnes enclosures sze 104.27 HYGIENICsErIEs nserts: CD... 64 poles + m 51 * CDD... 108 poles + m 64 * CQE... poles + m 83 * CSH... 24 poles + m 91 * CCE... 24 poles + m 100 * CNE, CSE... 24 poles + m 101 * CSS... 24 poles + m 121 * CT, CTE, CTSE *) 24 poles + m 129 and 133 * CE, CSE 10+2 (aux) poles + m 139 * CCE... 10+2 (aux) poles + m 138 * CE... 16+2 (aux) poles + m 145 * CCE... 16+2 (aux) poles + m 144 * CX... 4/8 poles + m 155 * IXO... 6 modules 156-195 * CDS... 42 poles + m 9 ** CQEE... 64 poles + m 16 *** *) only for standard nsulatng verson THIH *** refer to Supplement October 2013 catalogue page nsert centre dstance: 104 x 27 mm housngs wth double lever HNBR hoods wth 4 pegs descrpton part No. entry part No. entry bulkhead mountng housng wth thermoplastc levers THIH 24 surface mountng housng wth thermoplastc levers TAPH 24.32 32 surface mountng housng wth thermoplastc levers TAPH 24.40 40 wth pegs, sde entry TAO 24.32 32 wth pegs, sde entry TAO 24.40 40 wth pegs, top entry TAV 24.32 32 wth pegs, top entry TAV 24.40 40 panel cut-out for bulkhead mountng housng n mm dmensons n mm dmensons n mm ø 4,5 THIH 24 TAO 24.32 and TAO 24.40 160 76 80 27 HYGEnC T-TYPE/H 32 35 112 130 5 143,5 123 TAPH 24.32 and TAPH 24.40 TAV 24.32 and TAV 24.40 160 80 Ø 5,5 91 76 132 45 6 123 144 57 The surface mountng, hgh constructon housngs are suppled wth an open threaded entry and dametrcally opposte a closed threaded entry whch can be opened by the user f requred (wth sutable tool). IP66 IP69 - ambent temperature lmts -40 C / +70 C dmensons shown are not bndng and may be changed wthout notce 44

T-TYPE/ H producton lnes enclosures sze 104.27 HYGIENICsErIEs nserts: CD... 64 poles + m 51 * CDD... 108 poles + m 64 * CQE... poles + m 83 * CSH... 24 poles + m 91 * CCE... 24 poles + m 100 * CNE, CSE... 24 poles + m 101 * CSS... 24 poles + m 121 * CT, CTE, CTSE *) 24 poles + m 129 and 133 * CE, CSE 10+2 (aux) poles + m 139 * CCE... 10+2 (aux) poles + m 138 * CE... 16+2 (aux) poles + m 145 * CCE... 16+2 (aux) poles + m 144 * CX... 4/8 poles + m 155 * IXO... 6 modules 156-195 * CDS... 42 poles + m 9 ** CQEE... 64 poles + m 16 *** *) only for standard nsulatng verson THIH *** refer to Supplement October 2013 catalogue page nsert centre dstance: 104 x 27 mm hoods wth double lever top entry covers descrpton part No. entry part No. wth thermoplastc levers and TAVH 24 G32 32 wth thermoplastc levers and TAVH 24 G40 40 wth 4 pegs TCHC 24 wth 2 thermoplastc levers and HNBR dmensons n mm HNBR THCH 24 G dmensons n mm TAVH 24 G32 and TAVH 24 G40 TCHC 24 160 91 123 123 THCH 24 G 160 HYGEnC T-TYPE/H 123 IP66 IP69 - ambent temperature lmts -40 C / +70 C dmensons shown are not bndng and may be changed wthout notce 45

T-TYPE/ C low-temperature enclosures sze 44.27 HYGIENICsErIEs nserts: CDD... 24 poles + m 59 * CQE... 10 poles + m 80 * CSH... 6 poles + m 88 * CCE... 6 poles + m 94 * CNE, CSE... 6 poles + m 95 * CSS... 6 poles + m 118 * CT, CTE, CTSE *).. 6 poles + m 126 and 130 * IXO... 2 modules 156-195 * CDS... 9 poles + m 6 ** housngs wth sngle lever hoods wth 2 pegs *) only for standard nsulatng verson THIC nsert centre dstance: 44 x 27 mm SILICONE descrpton part No. entry part No. entry bulkhead mountng housng wth thermoplastc lever THIC 06 L surface mountng housng wth thermoplastc lever TAPC 06 L25 25 surface mountng housng wth thermoplastc lever TAPC 06 L32 32 wth pegs, sde entry TAO 06 L25 25 wth pegs, sde entry TAO 06 L32 32 con poln, uscta vertcale TAV 06 L25 25 con poln, uscta vertcale TAV 06 L32 32 panel cut-out for bulkhead mountng housng n mm dmensons n mm dmensons n mm ø 4,5 THIC 06 L TAO 06 L25 and TAO 06 L32 75 66 72 74 52 70 27 83,5 5 63 HYGEnC T-TYPE/C low-temperature 32 35 TAPC 06 L25 and TAPC 06 L32 75 73 ( ) 70 45 82 57 6 Ø 5,5 TAV 06 L25 and TAV 06 L32 87 72 63 71,5 ( ) The surface mountng, hgh constructon housngs are suppled wth an open threaded entry ( ) and dametrcally opposte a closed threaded entry whch can be opened by the user f requred (wth sutable tool). IP66 IP69 - ambent temperature lmts -50 C/+70 C dmensons shown are not bndng and may be changed wthout notce

T-TYPE/ C low-temperature enclosures sze 44.27 HYGIENICsErIEs nserts: CDD... 24 poles + m 59 * CQE... 10 poles + m 80 * CSH... 6 poles + m 88 * CCE... 6 poles + m 94 * CNE, CSE... 6 poles + m 95 * CSS... 6 poles + m 118 * CT, CTE, CTSE *).. 6 poles + m 126 and 130 * IXO... 2 modules 156-195 * CDS... 9 poles + m 6 ** hoods wth sngle lever top entry covers *) only for standard nsulatng verson THIC nsert centre dstance: 44 x 27 mm SILICONE SILICONE descrpton part No. entry part No. wth thermoplastc lever and TAVC 06 LG25 25 wth thermoplastc lever and TAVC 06 LG32 32 wth pegs wth thermoplastc lever and dmensons n mm TAVC 06 LG25 and TAVC 06 LG32 TCHC 06 L THCC 06 LG dmensons n mm TCHC 06 L 75 66 87 63 63 THCC 06 LG 63 75 66 HYGEnC T-TYPE/C low-temperature IP66 IP69 - ambent temperature lmts -50 C/+70 C dmensons shown are not bndng and may be changed wthout notce 47

T-TYPE/ C low-temperature enclosures sze 57.27 HYGIENICsErIEs nserts: housngs wth double lever hoods wth 4 pegs CDD... 42 poles + m 61 * CQE... 18 poles + m 81 * CSH... 10 poles + m 89 * CCE... 10 poles + m 96 * CNE, CSE... 10 poles + m 97 * CSS... 10 poles + m 119 * CT, CTE, CTSE *) 10 poles + m 127 and 131 * CSE... 3+2 (aux) poles + m 135 * CCE... 3+2 (aux) poles + m 134 * CE... 3+2 (aux) poles + m 135 * CX... 8/24 poles + m 151 * IXO... 3 modules 156-195 * CDS... 18 poles + m 7 ** *) only for standard nsulatng verson THIC nsert centre dstance: 57 x 27 mm SILICONE descrpton part No. entry part No. entry bulkhead mountng housng wth thermoplastc levers THIC 10 surface mountng housng wth thermoplastc levers TAPC 10.25 25 surface mountng housng wth thermoplastc levers TAPC 10.32 32 wth pegs, sde entry TAO 10.25 25 wth pegs, sde entry TAO 10.32 32 wth pegs, top entry TAV 10.25 25 wth pegs, top entry TAV 10.32 32 panel cut-out for bulkhead mountng housng n mm dmensons n mm dmensons n mm ø 4,5 THIC 10 TAO 10.25 and TAO 10.32 65 83 113 27 72 74 HYGEnC T-TYPE/C low-temperature 32 35 5 96,5 76 TAPC 10.25 and TAPC 10.32 TAV 10.25 and TAV 10.32 113 87 80 Ø 5,5 72 82 45 6 76 94 57 The surface mountng, hgh constructon housngs are suppled wth an open threaded entry and dametrcally opposte a closed threaded entry whch can be opened by the user f requred (wth sutable tool). IP66 IP69 - ambent temperature lmts -50 C/+70 C dmensons shown are not bndng and may be changed wthout notce 48

T-TYPE/ C low-temperature enclosures sze 57.27 HYGIENICsErIEs nserts: CDD... 42 poles + m 61 * CQE... 18 poles + m 81 * CSH... 10 poles + m 89 * CCE... 10 poles + m 96 * CNE, CSE... 10 poles + m 97 * CSS... 10 poles + m 119 * CT, CTE, CTSE *) 10 poles + m 127 and 131 * CSE... 3+2 (aux) poles + m 135 * CCE... 3+2 (aux) poles + m 134 * CE... 3+2 (aux) poles + m 135 * CX... 8/24 poles + m 151 * IXO... 3 modules 156-195 * CDS... 18 poles + m 7 ** *) only for standard nsulatng verson THIC nsert centre dstance: 57 x 27 mm hoods wth double lever top entry SILICONE covers SILICONE descrpton part No. entry part No. wth thermoplastc levers and TAVC 10 G25 25 wth thermoplastc levers and TAVC 10 G32 32 wth 4 pegs TCHC 10 wth 2 thermoplastc levers and dmensons n mm THCC 10 G dmensons n mm TAVC 10 G25 and TAVC 10 G32 TCHC 10 113 87 76 76 THCC 10 G 113 76 HYGEnC T-TYPE/C low-temperature IP66 IP69 - ambent temperature lmts -50 C/+70 C dmensons shown are not bndng and may be changed wthout notce 49

T-TYPE/ C low-temperature enclosures sze 77.27 HYGIENICsErIEs nserts: CD... 40 poles + m 49 * CDD... 72 poles + m 62 * CQE... 32 poles + m 82 * CSH... 16 poles + m 90 * CCE... 16 poles + m 98 * CNE, CSE... 16 poles + m 99 * CSS... 16 poles + m 120 * CT, CTE, CTSE *).. 16 poles + m 128 and 132 * CE, CSE 6+2 (aux) poles + m 137 * CCE... 6+2 (aux) poles + m 136 * CP... 6 poles + m 149 * CX... 6/36 and 12/2 poles + m 152-153 * CX... 4/0 and 4/2 poles + m 154 * IXO... 4 modules 156-195 * CDS... 27 poles + m 8 ** CQEE... 40 poles + m 15 *** *) only for standard nsulatng verson THIC *** refer to Supplement October 2013 catalogue page nsert centre dstance: 77,5 x 27 mm housngs wth double lever SILICONE hoods wth 4 pegs descrpton part No. entry part No. entry bulkhead mountng housng wth thermoplastc levers THIC 16 surface mountng housng wth thermoplastc levers TAPC 16.32 32 surface mountng housng wth thermoplastc levers TAPC 16.40 40 wth pegs, sde entry TAO 16.32 32 wth pegs, sde entry TAO 16.40 40 wth pegs, top entry TAV 16.32 32 wth pegs, top entry TAV 16.40 40 panel cut-out for bulkhead mountng housng n mm dmensons n mm dmensons n mm ø 4,5 THIC 16 TAO 16.32 and TAO 16.40 133,5 76 80 HYGEnC T-TYPE/C low-temperature 32 35 86 103 27 5 116,5 96,5 TAPC 16.32 and TAPC 16.40 TAV 16.32 and TAV 16.40 133,5 80 91 Ø 5,5 76 105 45 6 96,5 117 57 The surface mountng, hgh constructon housngs are suppled wth an open threaded entry and dametrcally opposte a closed threaded entry whch can be opened by the user f requred (wth sutable tool). IP66 IP69 - ambent temperature lmts -50 C/+70 C dmensons shown are not bndng and may be changed wthout notce 50

T-TYPE/ C low-temperature enclosures sze 77.27 HYGIENICsErIEs nserts: CD... 40 poles + m 49 * CDD... 72 poles + m 62 * CQE... 32 poles + m 82 * CSH... 16 poles + m 90 * CCE... 16 poles + m 98 * CNE, CSE... 16 poles + m 99 * CSS... 16 poles + m 120 * CT, CTE, CTSE *).. 16 poles + m 128 and 132 * CE, CSE 6+2 (aux) poles + m 137 * CCE... 6+2 (aux) poles + m 136 * CP... 6 poles + m 149 * CX... 6/36 and 12/2 poles + m 152-153 * CX... 4/0 and 4/2 poles + m 154 * IXO... 4 modules 156-195 * CDS... 27 poles + m 8 ** CQEE... 40 poles + m 15 *** *) only for standard nsulatng verson THIC *** refer to Supplement October 2013 catalogue page nsert centre dstance: 77,5 x 27 mm hoods wth double lever top entry covers descrpton part No. entry part No. wth thermoplastc levers and TAVC 16 G32 32 wth thermoplastc levers and TAVC 16 G40 40 wth 4 pegs TCHC 16 wth 2 thermoplastc levers and SILICONE dmensons n mm SILICONE THCC 16 G dmensons n mm TAVC 16 G32 and TAVC 16 G40 TCHC 16 133,5 91 96,5 96,5 THCC 16 G 133,5 96,5 HYGEnC T-TYPE/C low-temperature IP66 IP69 - ambent temperature lmts -50 C/+70 C dmensons shown are not bndng and may be changed wthout notce 51

T-TYPE/ C low-temperature enclosures sze 104.27 HYGIENICsErIEs nserts: CD... 64 poles + m 51 * CDD... 108 poles + m 64 * CQE... poles + m 83 * CSH... 24 poles + m 91 * CCE... 24 poles + m 100 * CNE, CSE... 24 poles + m 101 * CSS... 24 poles + m 121 * CT, CTE, CTSE *) 24 poles + m 129 and 133 * CE, CSE 10+2 (aux) poles + m 139 * CCE... 10+2 (aux) poles + m 138 * CE... 16+2 (aux) poles + m 145 * CCE... 16+2 (aux) poles + m 144 * CX... 4/8 poles + m 155 * IXO... 6 modules 156-195 * CDS... 42 poles + m 9 ** CQEE... 64 poles + m 16 *** *) only for standard nsulatng verson THIC *** refer to Supplement October 2013 catalogue page nsert centre dstance: 104 x 27 mm housngs wth double lever SILICONE hoods wth 4 pegs descrpton part No. entry part No. entry bulkhead mountng housng wth thermoplastc levers THIC 24 surface mountng housng wth thermoplastc levers TAPC 24.32 32 surface mountng housng wth thermoplastc levers TAPC 24.40 40 wth pegs, sde entry TAO 24.32 32 wth pegs, sde entry TAO 24.40 40 wth pegs, top entry TAV 24.32 32 wth pegs, top entry TAV 24.40 40 panel cut-out for bulkhead mountng housng n mm dmensons n mm dmensons n mm ø 4,5 THIC 24 TAO 24.32 and TAO 24.40 160 76 80 27 HYGEnC T-TYPE/C low-temperature 32 35 112 130 5 143,5 123 TAPC 24.32 and TAPC 24.40 TAV 24.32 and TAV 24.40 160 91 80 76 Ø 5,5 132 45 6 123 144 57 The surface mountng, hgh constructon housngs are suppled wth an open threaded entry and dametrcally opposte a closed threaded entry whch can be opened by the user f requred (wth sutable tool). IP66 IP69 - ambent temperature lmts -50 C/+70 C dmensons shown are not bndng and may be changed wthout notce 52

T-TYPE/ C low-temperature enclosures sze 104.27 HYGIENICsErIEs nserts: CD... 64 poles + m 51 * CDD... 108 poles + m 64 * CQE... poles + m 83 * CSH... 24 poles + m 91 * CCE... 24 poles + m 100 * CNE, CSE... 24 poles + m 101 * CSS... 24 poles + m 121 * CT, CTE, CTSE *) 24 poles + m 129 and 133 * CE, CSE 10+2 (aux) poles + m 139 * CCE... 10+2 (aux) poles + m 138 * CE... 16+2 (aux) poles + m 145 * CCE... 16+2 (aux) poles + m 144 * CX... 4/8 poles + m 155 * IXO... 6 modules 156-195 * CDS... 42 poles + m 9 ** CQEE... 64 poles + m 16 *** *) only for standard nsulatng verson THIC *** refer to Supplement October 2013 catalogue page nsert centre dstance: 104 x 27 mm hoods wth double lever top entry covers descrpton part No. entry part No. wth thermoplastc levers and TAVC 24 G32 32 wth thermoplastc levers and TAVC 24 G40 40 wth 4 pegs TCHC 24 wth 2 thermoplastc levers and SILICONE dmensons n mm SILICONE THCC 24 G dmensons n mm TAVC 24 G32 and TAVC 24 G40 TCHC 24 160 91 123 123 THCC 24 G 160 123 HYGEnC T-TYPE/C low-temperature IP66 IP69 - ambent temperature lmts -50 C/+70 C dmensons shown are not bndng and may be changed wthout notce 53

ULTIPOLE CONNECTORS Important Notes mportant notes 54 I.L..E. SpA desgns and manufactures complete solutons for heavy duty electrcal power connectons. The connector (although offered to the user as a varety of elements, usually nserts and enclosures, to allow the selecton of the deal combnaton) has been desgned as a sngle part and tested to be complant wth the essental safety requrements of the EU Low Volage Drectve 2006/95/EC and n partcular the EN 61984 standard. The desgn of ths modular system guarantees that every approved combnaton of nserts, enclosures and accessores cannot result as mproper. The products n ths catalogue alone cannot guarantee the best functonalty upon nstallaton, as ths depends also on ther correct nstallaton nto servce whch must be performed n complance wth the applcable system safety standards and accordng to the rule of the art. Therefore the effectveness of the nstallaton of the connector depends on the choces of the end user who must also take nto account the followng safety requrements. Connectors must not be connected or dsconnected when lve or under load. After wrng the nserts t s necessary to verfy the contnuty of the protectve earth connectons. The correct couplng of the nserts s guaranteed only f they are nstalled (wth the four fxng screws suppled) nsde the correspondng enclosures or onto compatble accessores n ths catalogue. I.L..E. SpA s not responsble for any dfferent applcaton. Wrng of screw-type termnal connectons must be carred out applyng the correct tghtenng torque n order to avod false contacts or damage to the conductor, the screw or the termnal. Crmpng tools and contacts used should preferably be suppled by the same manufacturer to avod dffcultes wth the nserton and retenton of the contacts themselves. Correct wrng of sprng-clamp connecton nserts s guaranteed only when the correct screwdrver ndcated n the specfc catalogue, or possbly on the nsert, s used. Avod forcng the contacts durng connecton and dsconnecton. Connectors must be coupled and uncoupled n the axal drecton wth respect to the contacts, wthout bendng and pullng the attached conductor bundles or cables. Installaton of two nserts sde by sde, n enclosures wth two bays, must respect the polarty drawng marked on the nsert (or the contact-sde vew, as shown n ths catalogue) to avod nverted couplng. The nstallaton of two or more dentcal connectors sde by sde s recommended only wth the use of codng pns n order to avod msmatched couplngs. In order to keep the declared degree of protecton (IP code), enclosures must be completed wth cable glands and/or other accessores wth at least an equal protecton ratng. oreover, the IP protecton ratng (accordng to ) s guaranteed when the enclosures, complete wth nserts, are coupled and locked wth ther lockng levers (or devces). Fnally, please note: - I.L..E. SpA cannot be held responsble for ndvdual components n uses other than those descrbed n ths catalogue. - I.L..E. SpA cannot be held responsble for ncorrect connector selecton n relaton to the envronmental condtons of the applcaton (e.g.: nfluence of ambent temperature, mosture, envronmental polluton, etc.). Connector nserts and ther enclosures are generally compatble wth smlar/equvalent products from other manufacturers, accordng to the last samples tested. Full compatblty cannot be guaranteed n the event of techncal changes made by other manufacturers. In partcular, maxmum performance of IP68 enclosures (Seres CG) cannot be guaranteed when coupled wth other manufacturers products. I.L..E. SpA takes no responsblty n verfyng whether the components heren contaned comply wth any specfc regulatons of felds of applcaton. www.lme.com

ULTIPOLE CONNECTORS Notes 55

ULTIPOLE CONNECTORS Techncal catalogues Cn12 ultpole connectors JE SErES ultpole connectors CSH-SQUCH Connecton wthout tools CdS Hgh densty sprng connecton v-type P67 EnCloSUrES V-Type lockng enclosures BG HoodS The space you have always wanted 56 techncal catalogues l-brd EnCloSUrES & CdA nserts CK-CKS SErES Wth code pns www.lme.com

ULTIPOLE CONNECTORS Sales Organzaton Sales organzaton Headquarter.l.m.E. SpA va arco Antono Colonna, 9 20149 lano - Italy +39 02345605.22 - fax +39 02331013 www.lme.com france lme france S.A.r.l. Rue Roland Garros - BP 125 Parc d Actvtés de l Aéroport 42163 Andrézeux-Bouthéon +33 (0) 4 77 36 23 36 - fax +33 (0) 4 77 36 97 97 e-mal: lme-france@lme.fr - www.lme.fr Germany lme GmbH ax-planck-straße 12-51674 Wehl +49 (0)2261-7955-0 fax +49 (0)2261-7955-5 (Auftragsannahme) - +49 (0)2261-7955-9 (Vertreb) e-mal: technk@lme.de - www.lme.de Unted Kngdom lme UK lmted 50 Evans Road, Venture Pont Speke, erseysde L24 9PB +44 (0) 151 3369321 - fax +44 (0) 151 3369326 e-mal: sales@lmeuk.co.uk - www.lmeuk.co.uk Sweden and nordc Countres lme nordc AB Transportvägen 18 242 Löddeköpnge (Sweden) + 18 28 00 - fax + 18 28 10 e-mal: nfo@lme.se - www.lme.se Japan lme JAPAn Co., ltd. Kobe Internatonal Busness Center 511-650-0047, 5-2, 5 - Chome, natojma nam-ach - Chuo-Ku, Kobe +81 7830 22005 - fax +81 7830 22060 www.lme.jp Chna lme CHnA rep. offce Room 201 Unversal Centre, no. 175 XangYan NanLu, - 200031 Shangha +86-21 - 62489961 - fax +86-21 - 62489961 www.lmechna.com www.lme.com

Ed.03/2015 w w w. l m e. c o m XDG TH 315 Catalogues