Uninterruptible Power Supply User-friendly Intelligent Ultra reliable
Range The Most Intelligent On-Line Double Conversion Power Protection System The range achieves higher reliability and greater immunity from mains power problems to the connected load by using a Digital Signal Processor (DSP). Ideally suited for mission critical applications such as vital servers, network and telecommunications equipment. The front panel LCD display provides real time status and parameter readings allowing simple operation and a full diagnosis for easy servicing. Using inverter control technology the 6kVA model and above can achieve N + X parallel redundancy operation allowing you to increase power capacity, reliability, safety and availability. In today s environment, UPS systems must satisfy the most challenging of applications and the versatile range have all the answers. Features: On-Line true double conversion Digital Signal Processor (DSP) technology Intelligent self-diagnostics Compact and lightweight design True Sinewave output LCD display control panel Multiple communication ports Output power factor 0.8 (optional 0.9) Wide input voltage range (110V to 300V) Programmable power outlets 50/60Hz frequency converter mode ECO mode operation for energy saving Smart battery charger design Active input power factor correction >0.99 Low current THD Emergency Power Off (EPO) function Long runtime versions Matching battery cabinets Galvanic isolation transformer (optional) Intelligent slot for SNMP or AS-400 internal card Available for 6kVA models and above N + X parallel redundancy Adjustable battery numbers Maintenance bypass
Intelligent self diagnostics The series UPS DSP controller systematically analyses each component and displays the result using the LCD panel. This feature allows your service technicians the ability to pinpoint and repair the UPS very quickly. Simple N + X parallel redundancy The BPC philosophy is both simple and elegant. UPS outputs are connected directly to the users distribution system, eliminating the vulnerable centralised static switch and control circuits. 6kVA and above models can be used in simple parallel operation with up to 3 units. This allows scalability for increased power capacity and improved reliability due to the redundancy operation. Easy and simple functions A precise LCD display provides real time status and parameter readings via the DSP controller. These include AC input and output voltage, frequency, battery voltage, load level, battery backup time, programmable output sockets status and modes of operation. Multiple communication options This feature will allow either the USB or RS-232 communication port to work with an SNMP interface simultaneously. Internal slots are provided for remote control and monitoring agents like SNMP and AS400 cards. Long runtime applications Matching battery cabinets can be connected to extend the backup time for all standard UPS systems. Even longer runtime (L) versions are available where the internal battery has been replaced with super efficient larger built-in chargers giving 4x and 8x times faster recharge capability. Intelligent power distribution With programmable power output sockets you are able to manage your power distribution more efficiently and independently control load segments. During a power failure this feature will enable you to extend battery autonomy backup time to mission critical devices by shutting down non-critical loads in a controlled manner.
High input Power Factor and low current THDi UPS series provides a clean environmental connection to the mains supply meeting today s industrial standard for energy saving and pollution free power. can achieve up to 0.99 input power factor as well as <6% input current THD. Smart charger design to optimize battery performance UPS are equipped with multi-stage charger designs to optimize battery discharge autonomy. Also, the charger management system will adjust the charging voltage according to environmental conditions thus providing temperature compensation and extending the useful service life of the batteries. ViewPower intelligent power management When there is a power interruption, ViewPower broadcasts a warning message to all workstation users on the network urging them to finish their current tasks. ViewPower automatically saves files and gracefully shuts down the operating system after a user-configured time period or when the UPS batteries are low on energy. ViewPower also provides:- Matching external battery cabinets For mission critical applications requiring longer runtimes or higher specification batteries, additional matching battery cabinets can easily be added. These have been designed both technically and aesthetically to complement the UPS, forming a combined unit which can be easily located without the need for special site considerations. For even larger battery systems or specialist battery installations, lower cost open or cladded racks can also be provided. User-friendly power analysis graphs Real Time dynamic graphs of UPS Data Environmentally friendly energy saving feature The intelligent microprocessor based control system, allows for the very low power consumption offered by the interactive economy-mode of operation which provides efficiencies as high as 97%. switches instantaneously to double conversion online operation when the mains becomes unstable and fluctuates outside the normal frequency and voltage parameters. Programmable frequency convertor The series may be used as a frequency converter. Simple programming through the front LCD panel will allow you to lock output frequency at 50Hz or 60Hz to suit frequency sensitive equipment. Password security protection and remote access management Allows control and monitoring of multiple UPS via LAN and Internet
General specification for Tower range Model PGPRO 1000 PGPRO 1500 PGPRO 2000 PGPRO 3000 PGPRO 6000 PGPRO 10000 Power Rating (VA/Watts) 1000/800 1500/1200 2000/1600 3000/2400 6000/4800 10,000/8000 Input Output Voltage 230 VAC Built-in Charger (max. Charging Current) 1.0A General Audible and Visual Alarms UPS status, load level, battery level, input/output voltage, discharge timer, and fault conditions Operating Temperature 0-40 C Humidity 90% RH maximum, non-condensing Acoustic Noise at 1m distance <45dBa <55dBa Interface Type Selectable USB / RS232 Interface Communication Options Relay contact board, SNMP / WEB card, etc. Dimensions (w x d x h) mm 145 x 397 x 220 190 x 421 x 318 250 x 592 x 576 Net Weight (kgs) including batteries 13 14 26 28 81 83 Battery Packs TOWER RACKMOUNT Accessories SNMP Card AS-400 Card Voltage (Vac) 120/140/160 ~ 300 VAC 160-300 VAC 160-300 VAC Frequency 40-70Hz 46-64Hz Phase Single phase with ground Single phase + ground + neutral Input Power Factor up to 0.99 @ 100% full load up to 0.99 @ 100% full load Voltage Regulation +/- 3% +/- 1% Power Factor 0.8 Wave Form Sine wave, THD <3% Sine wave, THD <3% Frequency Stability 50Hz +/- 0.1% (free running) Frequency Regulation 50Hz +/- 0.3% Transfer Time 0 ms no break Crest Factor 3:1 Efficiency (AC to AC)>85% >85% >88% >89% DC Start Yes Batteries Type Sealed lead acid maintenance free Capacity 12V 7AH x 3 pcs 12V 9AH x 3 pcs 12V 7AH x 6 pcs 12V 9AH x 6 pcs 12V 7AH x 20 pcs 12V 9AH x 20 pcs Voltage (Vdc) 36 72 240 Typical Recharge Time to 90% 3 hours 4 hours 5 hours Capacity 1kVA/1.5kVA 2kVA/3kVA 6kVA/10kVA 1kVA/1.5kVA/2kVA/3kVA 6kVA/10kVA Battery type & No. 7AH x 6 pcs 9AH x 6 pcs 7AH x 12pcs 9AH x 12 pcs 7AH x 20 pcs 9AH x 20 pcs 7AH x 12 pcs 9AH x 12 pcs 7AH x 20 pcs 9AH x 20 pcs Dimensions (w x d x h) mm 145 x 397 x 220 190 x 421 x 318 250 x 592 x 576 438 x 580 x 88 (2U) 438 x 580 x 133 (3U) Net Weight (kgs) 18 20 36 40 64 72 37 41 57 65 Ultra-compact, light and fast tool to remotely monitor and manage any UPS system BPC SNMP adaptors will connect directly to an Ethernet LAN with no necessity to hook up a computer system Capable of selecting the status of the dry-contact signal by setting jumper to meet different application requirements Suitable for IBM Server, computers, industrial and communication applications
General specification for Rackmount range Model PGPRO 1000R PGPRO 1500R PGPRO 2000R PGPRO 3000R PGPRO 6000R PGPRO 10000R Power Rating (VA/Watts) 1000/800 1500/1200 2000/1600 3000/2400 6000/4800 10,000/8000 Input Voltage (Vac) 120/140/160 ~ 300 VAC 160-300 VAC 160-300 VAC Frequency 40-70Hz 46-64Hz Phase Single phase with ground Single phase + ground + neutral Input Power Factor up to 0.99 @ 100% full load up to 0.99 @ 100% full load Output Voltage Voltage Regulation +/- 2% +/- 1% Power Factor 0.8 Wave Form Sine wave, THD <3% Sine wave, THD <2% Frequency Stability 230 VAC 50Hz +0.2% (free running) Frequency Regulation 50Hz or +/- 0.3% Transfer Time 0 ms no break Crest Factor 3:1 Efficiency (AC to AC) 85% 88% 89% DC Start Batteries Type Yes Sealed lead acid maintenance free Capacity 12V 7AH x 3 pcs 12V 9AH x 3 pcs 12V 7AH x 6 pcs 12V 9AH x 6 pcs 12V 7AH x 20 pcs 12V 9AH x 20 pcs Voltage (Vdc) 36 72 240 Recharge Time 3 hours 4 hours 5 hours Built-in Charger (max. charging current) 1.0A General Audible and Visual Alarms Operating Temperature Humidity UPS status, load level, battery level, input/output voltage, discharge timer, and fault conditions 0-40 C 90% RH maximum, non-condensing Acoustic Noise at 1m distance <45dBa <55dBa Interface Type Communication Options Selectable USB/ RS232 Interface Relay contact board, SNMP / WEB card etc Dimensions (w x d x h) mm 438 x 420 x 88 (2U) 438 x 580 x 133 (3U) UPS: 438 x 580 x 133 (3U) UPS: 438 x 668 x 133 (3U) Bat Cab: 438 x 580 x 133 (3U) Bat Cab: 438 x 580 x 133 (3U) Net Weight (kgs) 16 17 29 31 total = 74 total = 83 All product specifications are subject to change without notice. All trademarks mentioned are the properties of their respective owners. Issue 2 BPC EMEA Limited BPC House Romsey Industrial Estate Greatbridge Road Romsey Hampshire SO51 0HR United Kingdom Tel: +44 (0) 1794 521200 Fax: +44 (0) 1794 521400 e-mail: sales@bpc-ups.com www.bpc-ups.com