How To Program A Powerline System On A Dgma1D (Dgma) With A Smartcard And A Powercard (Dm1D) On A Pcv123D (Powerline) On An Iphone Or

Transcription

1 PCV123D Terminal Unit and DGM1D 1-Door Controller + Contactless Smartcard Reader Version 2.0 G00301FR0219V02 DGM1D: 1-door controller + contactless smartcard reader PCV123D: Terminal unit + PC software DGM1D Presentation General The DGM1D is a 1-door controller and contactless smartcard reader that manages up to 30 Trade & Service and unlimited cardholders. Each Trade & service account has a unique code which is loaded on the controller with the PCV123D terminal built-in smartcard reader. The date, hour validity is programmed on the Trade & Service badges and/or on the software. The DGM1D controller manages cardholders and master keys. The DGM1D controller is programmed with a PCV123D terminal unit. The default site code is: and the PCV123D terminal unit password is: It is recommended to change the default site code for security reason and to enter a 6-digit site code The compact size of the controller and the vandal resistant fireproof of the reader has made this contactless smartcard system very innovative and very simple to install. The other important innovation is the procedure to program a contactless smartcard, which is being done on the card and not on the controller as all the system on the marker. This way the installer saves precious time by the capability to program the badges and new badges from his office without having to go on the site. PC software: Login name: supervisor password: 1234 System description A complete system includes a DGM1D controller + reader and the PCV123D Terminal unit to program the system. DGM1 controller CDGM1 RS232 cable PCV123 Terminal terminal Unit unit PVP badge Reader 1

2 Features of the controller The DGM1D is a 1-door stand alone access control system. The controller is compatible with Mifare cards and badges. The controller can be connected three different modes: - 1 RS232 comm. port to connect a PCV123D terminal unit (JP3 jumper on and RS232 cable to connect on J1) - A wireless connection with the reader (remove JP3 jumper). The wireless communication is done between the reader and the terminal unit. - Connection to a reader controller from the network system: The DGM1D is then switched from a stand alone system to a network reader (remove JP2 jumper). The relay output is disabled for the cardholders. The same site code can be programmed on many controllers. The site code can be changed with the PCV123D terminal unit via the RS232 or wireless connection (JP1 jumper on). The cardholders badges can be enabled or disabled with the JP2 jumper. PCV123D Features The terminal unit has many purposes: - Management of the Trade & Service accounts - Reads smartcard - Manages the controllers via RS232 connection or wireless communication with reader - Enrollment and identification of the cardholders badges and master keys - Capability to manage the site from a PC JP1 : site code JP2 : cardholders JP3 :RS232 mode Badge enrollment unit Set the Date & Hour on the controller Set the date & hour of the controller on a new installation with the PCV123D terminal unit. When removing or replacing a battery make sure the «controller is not powered» when the battery is replaced insert tag protection. Remove the tag protection while the controller is powered; Set the date and the hour with the PCV123D Terminal unit. 2

3 Add or Modify a Trade & Service code in the controller The Trade & Service card comes in a smartcard format which enclose a unique code. Besides, the cardholders that can be programmed, up to 30 Trade & service unique codes could be programmed in the controller. The Trade & Services cardholders have access to the buildings at specific hours and dates. A Trade & Service account to get access to a building need to add the code in the controller. In the terminal unit, select «add service» menu, then insert the smartcard for the Trade & Service account you wish to create in the controller. Badges for the Trade & Service can be issued. This Trade & Service account is stored in the terminal unit database. It will be possible to add this Trade & Service account in other controller without the need to have the smartcard code of that Trade & Service. The access rights can be modified by the supervisor with the Terminal unit in «Modification» menu. The supervisor can modify or delete a Trade & Service account without the smartcard. The terminal unit can memorise up to 30 Trade & Service accounts. PC software The terminal unit can store up to 15 different sites (15 DGM1D). The Trade & Service account list can be transferred from the terminal unit to the PC software. The Trade & Service account list can be transferred from the PC software to the Terminal unit and then transferred to a DGM1D controller. Badges 3 access level badge types can be programmed on the PCV123D: Cardholder badges are programmed with the PCV123D Terminal Unit from the Enrollment badge menu. To activate a badge, the site code of the controller must be programmed on the badge. The site code is defined with a 5-digit + a 6th digit from 0 to 9. Cardholder badges can be programmed to grant access to a gate. To program the cardholder badges for the second reader only, the site code of this reader should be entered as follow : 5-digit + 6th digit E. Master keys are programmed with the PCV123D Terminal Unit from the Enrollment badge menu. The master keys have access to all sites (reader/door) which have the same 5 first digit and the 6th digit from 0 to 9. The site code for the master key should be programmed 5-digit + 6th digit F Site code controller # 1 to 10 controller for the gate Badges 1door+gate 5-digit + 0 to 9 one yes Badges gate 5-digit + E Only Master keys 5-digit + F all 10 readers yes Deleting cardholder badges and master keys To delete a cardholder badge or a master key, the code of the proximity card must be programmed on the reader (controller) with the PCV123D Terminal unit. It is possible to connect the PCV123D Terminal unit to the controller with an RS232 cable or with the RF transmitter. Select «Blacklist» menu in the PCV123D Terminal unit then add in blacklist menu. Enter the code of the cardholder badge and press enter. PCV123D Terminal Unit Menu The PCV123D terminal unit manages and programs DGM1D controller + reader ON, the terminal unit displays: «Terminal Version x.x». To enter in the menu press on the key or key of the keypad. Make sure that the PCV123D terminal unit is connected to the DGM1D controller (RS232 or RF), or to the PC software via the RS232 on the PC. Enter the site code of the controller and then the password: - Configuration - Trade & Service - Cardholders 3

4 Note : The terminal unit has an auto switch off of 5 minutes if not used. Switch ON The Terminal Unit ( any Key) 1: Connect To DGM1 (DGM1 Controller) Enter site code Enter password 2:Connect to PC PC software Connected to Controller Connected to PC Configuration Trade & Service Cardholder Configuration Date & Hour Enter date Enter hour Select summer/winter Password Enter New Password Confirm new password Valider la saisie Annuler modification Site Code (Put JP1 jumper) Enter new site code Relay Output Enter a new release time Configuration Confirmer la configuration 4

5 Cardholder Add in Blacklist 0x Delete from Blacklist Enter code of badge (last 8-digit) or to scroll Badge list 0X1230ADF0 View blacklist Confirm deletion or to scroll Badge list 0x1230ADF0 Program badge Present badge 0x or to scroll Present badge in front of badge enrolment Enter code of the badge Confirm enrolment Enrolment completed Enrolment cancelled Program master key or to scroll Present badge 0X12345EF0 Present badge in front of badge enrolment Enter code of the badge Update blacklist Confirm enrolment Enrolment completed Enrolment cancelled With PC software Confirm update Backup of blacklist Confirm backup or to scroll 5

6 Trade & Service Add T&S account 1: Smartcard (insert card) 2: Terminal unit list or to scroll Select Trade & Service account: 1/n account: Code - version 2/n account: Code - version... Edit T&S account (add new T&S account) Update T&S account (code version) or updater or to scroll T&S account list Select a T&S account 1/n account: Code - version 2/n account: Code - version... Modify access rights: Days Hours... Delete T&S account T&S account list Select a T&S account 1/n account: Code - version 2/n account: Code - version... Confirm deletion or to scroll Update T&S account or to scroll With PC software confirm update T&S account list backup or to scroll Confirm backup 6

7 Cardholders The cardholders need to use a contactless smart card on the DGM1D. The cardholder badge is programmed with a PCV123D Terminal unit which is also a Badge Enrollment unit. The DGM1D controller has a site code which should be programmed before fitting the system on a door (default site code : ). To give access to cardholder on a DGM1D reader, the site code of the controller must be programmed on the Cardholder badge. The controller has a memory storage of invalid badges called «Blacklist» maximum 200 cardholder badges. A lost badge must programmed in the «Blacklist» to invalidate the badge on the DGM1D reader. Without the PC software: All the code of the badges which have been programmed on the DGM1D reader must be written on list so it would be possible to enter them in the «Blacklist» to refuse the access on the reader. With the PC software: The «Blacklist» can be stored in the Terminal unit and then downloaded on the PC. The «Blacklist» can loaded from the PC to the Terminal unit and then uploaded to the DGM1D controller. PCV123D Keypad Presentation To switch ON the Terminal unit press on the power button located at the top right side. It powers off automatically after 5 minutes if not being used. The numerical keys are used for entering the values ; and the «A» and «B» keys to enter hexadecimals values (A to F). A, B, * and # keys can be used to scroll in the same sub-menu or on the display. The C is the ENTER key and D is the ESCAPE/DELETE key. It is also possible to select the next or previous menu with these keys. Up Right Down Left 7

8 PCV123D Terminal Unit The Terminal unit is powered with: - 2 x AA batteries 1.5 V - plug-in power supply: 300 ma To switch ON the Terminal unit press on the power button located at the top right side. It powers off automatically after 5 minutes if not being used. The hour on the terminal unit is updated each time the terminal unit is connected to the DGM1D controller and the Date/hour menu is opened. Jumpers There are 4 jumpers on the controller which need to be set prior to power the reader. Jumper must be set according to your configuration: - JP1 : The site code setting is enabled - JP2 : Cardholders programming is enabled - JP3 : RS232 connection between the DGM1D controller and the PCV123D Terminal unit Switch off the power on the controller, put the jumpers on and then put the power on. The new jumper configuration is set on the controller. Voltage specifications The voltage on the controller is protected by a polyswitch fuse and a transil diode. The input voltage can be done in AC or DC and polarity free. Refer to the datasheet of the DGM1D controller for more information Self-diagnosis Reader Test: When the controller is powered the LED on the reader lights on amber during 4 seconds and then lights off. RF Communication In case of a communication problem between the Terminal unit and the reader a message is displayed on the Terminal unit «default connection». Place the back of the Terminal unit against the reader The reading area of the Terminal unit should fit on the reader. Remove JP3 jumper Terminal unit back side 8