3-Pin Silicon Oscillator
|
|
|
- Mercy Lyons
- 7 years ago
- Views:
Transcription
1 General Description The MAX7375 is a silicon oscillator, intended as a low-cost improvement replacing ceramic resonators, crystals, and crystal oscillator modules used as the clock source for microcontrollers and UARTs in 3V, 3.3V, and 5V applications. The MAX7375 is a fully integrated oscillator, supplied at specific factory-trimmed frequencies with a rail-to-rail 50% duty cycle square-wave output. The oscillator frequency is generated directly without the use of a phase-locked loop (PLL). No additional components are used to set or adjust the frequency. Unlike typical crystal and ceramic resonator oscillator circuits, the MAX7375 is highly resistant to vibration and EMI. The high output drive current and absence of high-impedance nodes also makes the oscillator less susceptible to dirty or humid operating conditions. With a wide operating temperature range, the oscillator is a good choice for demanding home appliance environments. Available in 3-pin space-saving SC70 package, the MAX7375 is offered in standard and nonstandard factoryset frequencies ranging from 600kHz to 9.99MHz. See the MAX7381 data sheet for frequencies 10MHz. The MAX7375 s standard operating temperature range is -40 C to +125 C. See the Applications Information section for extended operating temperature range. Applications White Goods Portable Equipment Appliances and Controls Microcontroller Systems Hand-Held Products Typical Application Circuit 2.7V TO 5.5V V+ GND MAX7375 OSC1 µc Features 2.7V to 5.5V Operation Factory-Trimmed Oscillator (600kHz to 9.99MHz) No External Components Required ±10mA Output Drive Current 2% Initial Accuracy ±50ppm/ C Temp Drift Fast Startup Time: 5µs 40% to 60% Maximum Duty Cycle 5ns Output Rise and Fall Time-Low EMI Very Low EMI Susceptibility-No High-Impedance Nodes Very Low Jitter: 160ps P-P at 8MHz Tiny Surface-Mount Package (SC70) -40 C to +125 C Temperature Range Ordering Information PART TEMP RANGE PIN-PACKAGE MAX7375AXR105-T -40 C to +125 C 3 SC70-3 MAX7375AXR185-T -40 C to +125 C 3 SC70-3 MAX7375AXR365-T -40 C to +125 C 3 SC70-3 MAX7375AXR375-T -40 C to +125 C 3 SC70-3 MAX7375AXR405-T -40 C to +125 C 3 SC70-3 MAX7375AXR425-T -40 C to +125 C 3 SC70-3 MAX7375AXR805-T -40 C to +125 C 3 SC70-3 Note: The MAX7375 is available in factory-set frequencies from 600kHz to 9.99MHz. There are seven standard versions (1MHz, 1.84MHz, 3.58MHz, 3.69MHz, 4MHz, 4.19MHz, and 8MHz, as shown in the Selector Guide) with a required 2.5k order increment. Nonstandard frequencies are also available with a required 10k order increment. For nonstandard versions, contact factory for availability and ordering information. All versions available in tape-and-reel only. Pin Configuration and Selector Guide appear at end of data sheet. OSC ; Rev 4; 4/14
2 Absolute Maximum Ratings V+ to GND V to +6V to GND V to (V V) Continuous Power Dissipation (T A = +70 C) 3-Pin SC70 (derate 2.9mW/ C over +70 C)...235mW Operating Temperature Range C to +135 C Junction Temperature C Storage Temperature Range C to +150 C Lead Temperature (soldering, 10s) C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Electrical Characteristics (V+ = 2.7V to 5.5V, T A = -40 C to +125 C, unless otherwise noted. Typical values are at V+ = 5V, T A = +25 C, unless otherwise noted.) (Note 1) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Operating Supply Voltage V V Operating Supply Current I+ MAX7375A_R MAX7375A_R MAX7375A_R MAX7375A_R V+ 2.7V, I SOURCE = 2.5mA V Output High Voltage V OH V+ 4.5V, I SOURCE = 9mA V V+ 2.7, I SINK = 10mA 0.4 Output Low Voltage V OL V+ 4.5V, I SINK = 20mA 0.4 Initial Frequency Accuracy Frequency Temperature Sensitivity f V+ = 3.0V, T A = +25 C (Note 2) V+ = 2.7V to 5.5V, T A = +25 C (Note 2) MAX7375A_R _ MAX7375A_R _ (Note 3) ±50 ±325 ppm/ C Duty Cycle (Note 3) % Output Jitter Observation for 20s using a 500MHz oscilloscope (MAX7375A_R805) Note 1: All parameters are tested at T A = +25 C. Specifications over temperature are guaranteed by design and characterization. Note 2: Typical frequencies are nominal values. Note 3: Guaranteed by design and characterization. Not production tested. ma V V % 160 ps P-P Output Rise Time t R (Note 3) 5.0 ns Output Fall Time t F (Note 3) 2.5 ns Maxim Integrated 2
3 Typical Operating Characteristics (V+ = 5V, T A = +25 C, C L = 10pF, 8MHz output, unless otherwise noted.) DUTY CYCLE (%) DUTY CYCLE vs. TEMPERATURE MAX7375 toc01 DUTY CYCLE (%) DUTY CYCLE vs. SUPPLY VOLTAGE MAX7375 toc02 SUPPLY CURRENT (ma) SUPPLY CURRENT vs. TEMPERATURE V+ = 5V V+ = 2.7V MAX7375 toc TEMPERATURE ( C) SUPPLY VOLTAGE (V) TEMPERATURE ( C) SUPPLY CURRENT (ma) SUPPLY CURRENT vs. SUPPLY VOLTAGE MAX7375 toc04 NORMALIZED FREQUENCY FREQUENCY vs. SUPPLY VOLTAGE MAX7375 toc05 NORMALIZED FREQUENCY FREQUENCY vs. TEMPERATURE MAX7375 toc SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V) TEMPERATURE ( C) SUPPLY CURRENT (ma) SUPPLY CURRENT vs. FREQUENCY V+ = 5.5V V+ = 5V MAX7375 toc07 SETTLING TIME FROM START MAX7375 toc08 2V/div V+ 2V/div OUTPUT WAVEFORM WITH CL = 10pF MAX7375 toc09 1V/div 0.5 V+ = 2.7V FREQUENCY (MHz) 1µs/div 40ns/div Maxim Integrated 3
4 Typical Operating Characteristics (continued) (V+ = 5V, T A = +25 C, C L = 10pF, 8MHz output, unless otherwise noted.) OUTPUT WAVEFORM WITH C L = 50pF MAX7375 toc10 OUTPUT WAVEFORM WITH C L = 100pF MAX7375 toc11 1V/div 1V/div 40ns/div 40ns/div Pin Description PIN SC70 NAME FUNCTION 1 V+ Positive Supply Voltage 2 Clock Output. Output is push-pull. 3 GND Ground Detailed Description The MAX7375 is a replacement for ceramic resonators, crystals, and crystal oscillator modules as the clock source for microcontrollers and UARTs in 3V, 3.3V, and 5V applications. The MAX7375 is an integrated oscillator, supplied at specific frequencies just like crystals and resonators. A variety of popular standard frequencies are available. No external components are required for setting or adjusting the frequency. Supply Voltages The MAX7375 has been designed for use in systems with nominal supply voltages of 3V, 3.3V, or 5V and is specified for operation with supply voltages in the 2.7V to 5.5V range. Operation outside this range is not guaranteed. See the Absolute Maximum Ratings table for limit values of power-supply and pin voltages. Oscillator The clock output is a push-pull configuration and is capable of driving a ground-connected 1kΩ load or a positive supply connected 500Ω load to within 300mV of either supply rail. The clock output remains stable over the full operating voltage range and does not generate short output cycles during either power on or power off. A typical startup characteristic is shown in the Typical Operating Characteristics section. Output Jitter The MAX7375 s jitter performance is given in the Electrical Characteristics table as a peak-to-peak value obtained by observing the output of the MAX7375 for 20s with a 500MHz oscilloscope. Jitter measurements are approximately proportional to the period of the output frequency of the device. Thus, a 4MHz part has approximately twice the jitter value of an 8MHz part. The jitter performance of all clock sources degrades in the presence of mechanical and electrical interference. The MAX7375 is relatively immune to vibration, shock, and EMI influences and thus provides a considerably more robust clock source than crystal- or ceramic-resonatorbased oscillator circuits. Maxim Integrated 4
5 Applications Information Interfacing to a Microcontroller Clock Input The MAX7375 clock output is a push-pull, CMOS, logic output, which directly drives any microprocessor (µp) or microcontroller (µc) clock input. There are no impedancematching issues when using the MAX7375. Operate the MAX7375 and microcontroller (or other clock input device) from the same supply voltage level. Refer to the microcontroller data sheet for clock input compatibility with external clock signals. The MAX7375 requires no biasing components or load capacitance. When using the MAX7375 to retrofit a crystal oscillator, remove all biasing components from the oscillator input. Startup Performance The MAX7375 oscillator output stabilizes within a few cycles of operation after V+ rises to a sufficient voltage to start the oscillator, typically 1.65V at +25 C. Use a reset or similar voltage-detection circuit to disable devices connected to the MAX7375 until 5µs after the voltage on V+ has risen above 2.7V. Extended Temperature Operation The MAX7375 was tested to +135 C during product characterization and shown to function normally at this temperature (see Typical Operating Characteristics). However, production test and qualification is only performed from -40 C to +125 C at this time. Contact the factory if operation outside this range is required. Power-Supply Considerations The MAX7375 operates with power-supply voltages in the 2.7V to 5.5V range. Good power-supply decoupling is needed to maintain the power-supply rejection performance of the MAX7375. Use a 0.1µF surface-mount ceramic capacitor connected between V+ and GND and mounted as close as possible to the device. If possible, mount the MAX7375 close to the microcontroller s decoupling capacitor so that additional decoupling is not required. A larger value of bypass capacitor is recommended if the MAX7375 is to operate with a large capacitive load. Use a bypass capacitor value of at least 1000 times that of the output load capacitance. Selector Guide PART FREQUENCY (MHz) TOP MARK MAX7375AXR AOV MAX7375AXR AOU MAX7375AXR AOT MAX7375AXR AOS MAX7375AXR AOR MAX7375AXR AOQ MAX7375AXR AOP Pin Configuration TOP VIEW V+ 1 MAX7375AXR 2 SC70 3 GND Chip Information PROCESS: BiCMOS Maxim Integrated 5
6 Package Information For the latest package outline information and land patterns (footprints), go to Note that a +, #, or - in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE DOCUMENT NO. LAND PATTERN NO. 3 SC70 X Maxim Integrated 6
7 Revision History REVISION NUMBER REVISION DATE DESCRIPTION PAGES CHANGED 0 10/03 Initial release /07 Removed all references to MAX7375AUR_ and SOT23 package 1, 2, 4, 5 4 4/14 Removed automotive reference from General Description and Applications 1 For pricing, delivery, and ordering information, please contact Maxim Direct at , or visit Maxim Integrated s website at Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc Maxim Integrated Products, Inc. 7
V CC TOP VIEW. f SSO = 20MHz to 134MHz (DITHERED)
19-013; Rev 1; 10/11 0MHz to 13MHz Spread-Spectrum General Description The is a spread-spectrum clock modulator IC that reduces EMI in high clock-frequency-based, digital electronic equipment. Using an
Push-Pull FET Driver with Integrated Oscillator and Clock Output
19-3662; Rev 1; 5/7 Push-Pull FET Driver with Integrated Oscillator General Description The is a +4.5V to +15V push-pull, current-fed topology driver subsystem with an integrated oscillator for use in
Spread-Spectrum Crystal Multiplier DS1080L. Features
Rev 1; 3/0 Spread-Spectrum Crystal Multiplier General Description The is a low-jitter, crystal-based clock generator with an integrated phase-locked loop (PLL) to generate spread-spectrum clock outputs
ICS650-44 SPREAD SPECTRUM CLOCK SYNTHESIZER. Description. Features. Block Diagram DATASHEET
DATASHEET ICS650-44 Description The ICS650-44 is a spread spectrum clock synthesizer intended for video projector and digital TV applications. It generates three copies of an EMI optimized 50 MHz clock
Features. Modulation Frequency (khz) VDD. PLL Clock Synthesizer with Spread Spectrum Circuitry GND
DATASHEET IDT5P50901/2/3/4 Description The IDT5P50901/2/3/4 is a family of 1.8V low power, spread spectrum clock generators capable of reducing EMI radiation from an input clock. Spread spectrum technique
TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER. Features
DATASHEET ICS280 Description The ICS280 field programmable spread spectrum clock synthesizer generates up to four high-quality, high-frequency clock outputs including multiple reference clocks from a low-frequency
Cold-Junction-Compensated K-Thermocoupleto-Digital Converter (0 C to +1024 C)
19-2235; Rev 1; 3/02 Cold-Junction-Compensated K-Thermocoupleto-Digital General Description The performs cold-junction compensation and digitizes the signal from a type-k thermocouple. The data is output
ICS379. Quad PLL with VCXO Quick Turn Clock. Description. Features. Block Diagram
Quad PLL with VCXO Quick Turn Clock Description The ICS379 QTClock TM generates up to 9 high quality, high frequency clock outputs including a reference from a low frequency pullable crystal. It is designed
ICS514 LOCO PLL CLOCK GENERATOR. Description. Features. Block Diagram DATASHEET
DATASHEET ICS514 Description The ICS514 LOCO TM is the most cost effective way to generate a high-quality, high-frequency clock output from a 14.31818 MHz crystal or clock input. The name LOCO stands for
ICS650-01 SYSTEM PERIPHERAL CLOCK SOURCE. Description. Features. Block Diagram DATASHEET
DATASHEET ICS650-01 Description The ICS650-01 is a low-cost, low-jitter, high-performance clock synthesizer for system peripheral applications. Using analog/digital Phase-Locked Loop (PLL) techniques,
SPREAD SPECTRUM CLOCK GENERATOR. Features
DATASHEET ICS7152 Description The ICS7152-01, -02, -11, and -12 are clock generators for EMI (Electro Magnetic Interference) reduction (see below for frequency ranges and multiplier ratios). Spectral peaks
DSC1001. Low-Power Precision CMOS Oscillator 1.8~3.3V. Features. General Description. Benefits. Block Diagram
DSC.8~.V LowPower Precision CMOS Oscillator General Description The DSC is a silicon MEMS based CMOS oscillator offering excellent jitter and stability performance over a wide range of supply voltages
1 TO 4 CLOCK BUFFER ICS551. Description. Features. Block Diagram DATASHEET
DATASHEET 1 TO 4 CLOCK BUFFER ICS551 Description The ICS551 is a low cost, high-speed single input to four output clock buffer. Part of IDT s ClockBlocks TM family, this is our lowest cost, small clock
High-Speed, Low-Power, 3V/5V, Rail-to-Rail, Single-Supply Comparators MAX941/MAX942/ MAX944. General Description. Features. Ordering Information
General Description The MAX941/MAX94/ are single/dual/quad highspeed comparators optimized for systems powered from a 3V or 5V supply. These devices combine high speed, low power, and rail-to-rail inputs.
On/Off Controller with Debounce and
19-4128; Rev ; 5/8 On/Off Controller with Debounce and General Description The is a pushbutton on/off controller with a single switch debouncer and built-in latch. It accepts a noisy input from a mechanical
AAT3520/2/4 MicroPower Microprocessor Reset Circuit
General Description Features PowerManager The AAT3520 series of PowerManager products is part of AnalogicTech's Total Power Management IC (TPMIC ) product family. These microprocessor reset circuits are
VT-802 Temperature Compensated Crystal Oscillator
T-802 Temperature Compensated Crystal Oscillator T-802 Description ectron s T-802 Temperature Compensated Crystal Oscillator (TCXO) is a quartz stabilized, CMOS output, analog temperature compensated oscillator,
Low-Jitter I 2 C/SPI Programmable Dual CMOS Oscillator
eet General Description The DSC2111 and series of programmable, highperformance dual CMOS oscillators utilizes a proven silicon MEMS technology to provide excellent jitter and stability while incorporating
ABRIDGED DATA SHEET EVALUATION KIT AVAILABLE
EVALUATION KIT AVAILABLE General Description DeepCoverM embedded security solutions cloak sensitive data under multiple layers of advanced physical security to provide the most secure key storage possible.
Features. Applications
LM555 Timer General Description The LM555 is a highly stable device for generating accurate time delays or oscillation. Additional terminals are provided for triggering or resetting if desired. In the
MAX14760/MAX14762/MAX14764 Above- and Below-the-Rails Low-Leakage Analog Switches
19-652; Rev 1; 8/12 EVALUATION KIT AVAILABLE MAX1476// General Description The MAX1476// analog switches are capable of passing bipolar signals that are beyond their supply rails. These devices operate
AAT4280 Slew Rate Controlled Load Switch
General Description Features SmartSwitch The AAT4280 SmartSwitch is a P-channel MOSFET power switch designed for high-side load switching applications. The P-channel MOSFET device has a typical R DS(ON)
CAN bus ESD protection diode
Rev. 04 15 February 2008 Product data sheet 1. Product profile 1.1 General description in a small SOT23 (TO-236AB) Surface-Mounted Device (SMD) plastic package designed to protect two automotive Controller
VS-500 Voltage Controlled SAW Oscillator
VS-500 Voltage Controlled SAW Oscillator Features Improved High Performance ASIC Industry Standard Package, 9 x 14 x 4.5 mm Frequencies from 155 MHz to 850 MHz 3.3 V or 5.0 V Operation At 155.52 MHz, Jitter
LOW POWER SPREAD SPECTRUM OSCILLATOR
LOW POWER SPREAD SPECTRUM OSCILLATOR SERIES LPSSO WITH SPREAD-OFF FUNCTION 1.0 110.0 MHz FEATURES + 100% pin-to-pin drop-in replacement to quartz and MEMS based XO + Low Power Spread Spectrum Oscillator
LM118/LM218/LM318 Operational Amplifiers
LM118/LM218/LM318 Operational Amplifiers General Description The LM118 series are precision high speed operational amplifiers designed for applications requiring wide bandwidth and high slew rate. They
R EXT THERMISTOR. Maxim Integrated Products 1
19-2219; Rev 0; 2/02 Thermistor-to-Digital Converter General Description The converts an external thermistor s temperature-dependent resistance directly into digital form. The thermistor and an external
Spread Spectrum Clock Generator AK8126A
Features Output Frequency Range: 22.5MHz 32MHz, 45 MHz 64MHz 90MHz 128MHz Configurable Spread Spectrum Modulation: - AKEMD s Original Spread Spectrum Profile - Modulation Ratio: Center Spread: ±0.25%,
How to Read a Datasheet
How to Read a Datasheet Prepared for the WIMS outreach program 5/6/02, D. Grover In order to use a PIC microcontroller, a flip-flop, a photodetector, or practically any electronic device, you need to consult
High-speed switching diodes. Type number Package Configuration Package NXP JEITA JEDEC
Rev. 8 18 November 2010 Product data sheet 1. Product profile 1.1 General description, encapsulated in small Surface-Mounted Device (SMD) plastic packages. Table 1. Product overview Type number Package
DG2302. High-Speed, Low r ON, SPST Analog Switch. Vishay Siliconix. (1-Bit Bus Switch with Level-Shifter) RoHS* COMPLIANT DESCRIPTION FEATURES
High-Speed, Low r ON, SPST Analog Switch (1-Bit Bus Switch with Level-Shifter) DG2302 DESCRIPTION The DG2302 is a high-speed, 1-bit, low power, TTLcompatible bus switch. Using sub-micron CMOS technology,
DS1220Y 16k Nonvolatile SRAM
19-5579; Rev 10/10 NOT RECOENDED FOR NEW DESIGNS 16k Nonvolatile SRAM www.maxim-ic.com FEATURES 10 years minimum data retention in the absence of external power Data is automatically protected during power
High Precision TCXO / VCTCXO Oscillators
Available at Digi-Key** www.digikey.com High Precision TCXO / VCTCXO Oscillators 2111 Comprehensive Drive Phone: 60-81- 722 Fax: 60-81- 00 US Headquarters: 60-81-722 European Headquarters: +-61-72221 Description:
High-Speed, Low r ON, SPST Analog Switch (1-Bit Bus Switch)
High-Speed, Low r ON, SPST Analog Switch (1-Bit Bus Switch) DG2301 ishay Siliconix DESCRIPTION The DG2301 is a high-speed, 1-bit, low power, TTLcompatible bus switch. Using sub-micron CMOS technology,
TLI4946. Datasheet TLI4946K, TLI4946-2K, TLI4946-2L. Sense and Control. May 2009
May 2009 TLI4946 High Precision Hall Effect Latches for Industrial and Consumer Applications TLI4946K, TLI4946-2K, TLI4946-2L Datasheet Rev. 1.0 Sense and Control Edition 2009-05-04 Published by Infineon
LM566C Voltage Controlled Oscillator
LM566C Voltage Controlled Oscillator General Description The LM566CN is a general purpose voltage controlled oscillator which may be used to generate square and triangular waves the frequency of which
STLQ015. 150 ma, ultra low quiescent current linear voltage regulator. Description. Features. Application
150 ma, ultra low quiescent current linear voltage regulator Description Datasheet - production data Features SOT23-5L Input voltage from 1.5 to 5.5 V Very low quiescent current: 1.0 µa (typ.) at no load
PECL and LVDS Low Phase Noise VCXO (for 65-130MHz Fund Xtal) XIN XOUT N/C N/C CTRL VCON (0,0) OESEL (Pad #25) 1 (default)
Reserved BUF BUF 62 mil OESEL^ Reserved Reserved PL520-30 FEATURES 65MHz to 130MHz Fundamental Mode Crystals. Output range (no PLL): 65MHz 130MHz (3.3V). 65MHz 105MHz (2.5V). Low Injection Power for crystal
40 V, 200 ma NPN switching transistor
Rev. 01 21 July 2009 Product data sheet BOTTOM VIEW 1. Product profile 1.1 General description NPN single switching transistor in a SOT883 (SC-101) leadless ultra small Surface-Mounted Device (SMD) plastic
4 OUTPUT PCIE GEN1/2 SYNTHESIZER IDT5V41186
DATASHEET IDT5V41186 Recommended Applications 4 Output synthesizer for PCIe Gen1/2 General Description The IDT5V41186 is a PCIe Gen2 compliant spread-spectrum-capable clock generator. The device has 4
LM386 Low Voltage Audio Power Amplifier
Low Voltage Audio Power Amplifier General Description The LM386 is a power amplifier designed for use in low voltage consumer applications. The gain is internally set to 20 to keep external part count
INTEGRATED CIRCUITS. NE558 Quad timer. Product data Supersedes data of 2001 Aug 03. 2003 Feb 14
INTEGRATED CIRCUITS Supersedes data of 2001 Aug 03 2003 Feb 14 DESCRIPTION The Quad Timers are monolithic timing devices which can be used to produce four independent timing functions. The output sinks
BAT54 series SOT23 Schottky barrier diodes Rev. 5 5 October 2012 Product data sheet 1. Product profile 1.1 General description
SOT2 Rev. 5 5 October 2012 Product data sheet 1. Product profile 1.1 General description Planar with an integrated guard ring for stress protection, encapsulated in a small SOT2 (TO-26AB) Surface-Mounted
Spread Spectrum Clock Generator
Spread Spectrum Clock Generator Features Generates a 1x (PCS3P5811), x (PCS3P581) and 4x() low EMI spread spectrum clock of the input frequency Provides up to 15dB of EMI suppression Input Frequency: 4MHz
Cold-Junction Compensated Thermocouple-to-Digital Converter
General Description The MAX31855 performs cold-junction compensation and digitizes the signal from a K-, J-, N-, T-, S-, R-, or E-type thermocouple. The data is output in a signed 14-bit, SPI-compatible,
AP331A XX G - 7. Lead Free G : Green. Packaging (Note 2)
Features General Description Wide supply Voltage range: 2.0V to 36V Single or dual supplies: ±1.0V to ±18V Very low supply current drain (0.4mA) independent of supply voltage Low input biasing current:
3-input EXCLUSIVE-OR gate. The 74LVC1G386 provides a 3-input EXCLUSIVE-OR function.
Rev. 02 3 September 2007 Product data sheet 1. General description The provides a 3-input EXCLUSIVE-OR function. The input can be driven from either 3.3 or 5 V devices. This feature allows the use of these
TS555. Low-power single CMOS timer. Description. Features. The TS555 is a single CMOS timer with very low consumption:
Low-power single CMOS timer Description Datasheet - production data The TS555 is a single CMOS timer with very low consumption: Features SO8 (plastic micropackage) Pin connections (top view) (I cc(typ)
LM1084 5A Low Dropout Positive Regulators
5A Low Dropout Positive Regulators General Description The LM1084 is a series of low dropout voltage positive regulators with a maximum dropout of 1.5 at 5A of load current. It has the same pin-out as
PESDxU1UT series. 1. Product profile. Ultra low capacitance ESD protection diode in SOT23 package. 1.1 General description. 1.
Rev. 02 20 August 2009 Product data sheet 1. Product profile 1.1 General description Ultra low capacitance ElectroStatic Discharge (ESD) protection diode in a SOT23 (TO-236AB) small SMD plastic package
The 74LVC1G11 provides a single 3-input AND gate.
Rev. 8 17 September 2015 Product data sheet 1. General description The provides a single 3-input AND gate. The input can be driven from either 3.3 V or 5 V devices. This feature allows the use of this
www.jameco.com 1-800-831-4242
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. LF411 Low Offset, Low Drift JFET Input Operational Amplifier General Description
LIN-bus ESD protection diode
Rev. 3 31 May 2011 Product data sheet 1. Product profile 1.1 General description in a very small SOD323 (SC-76) Surface-Mounted Device (SMD) plastic package designed to protect one automotive Local Interconnect
65 V, 100 ma PNP/PNP general-purpose transistor
Rev. 02 19 February 2009 Product data sheet 1. Product profile 1.1 General description PNP/PNP general-purpose transistor pair in a very small SOT363 (SC-88) Surface-Mounted Device (SMD) plastic package.
NE555 SA555 - SE555. General-purpose single bipolar timers. Features. Description
NE555 SA555 - SE555 General-purpose single bipolar timers Features Low turn-off time Maximum operating frequency greater than 500 khz Timing from microseconds to hours Operates in both astable and monostable
How To Make An Electric Static Discharge (Esd) Protection Diode
Rev. 01 0 October 2008 Product data sheet 1. Product profile 1.1 General description Ultra low capacitance bidirectional ElectroStatic Discharge (ESD) protection diodes in small Surface-Mounted Device
NE555 SA555 - SE555. General-purpose single bipolar timers. Features. Description
NE555 SA555 - SE555 General-purpose single bipolar timers Features Low turn-off time Maximum operating frequency greater than 500 khz Timing from microseconds to hours Operates in both astable and monostable
INTEGRATED CIRCUITS DATA SHEET. TDA7000 FM radio circuit. Product specification File under Integrated Circuits, IC01
INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC01 May 1992 GENERAL DESCRIPTION The is a monolithic integrated circuit for mono FM portable radios, where a minimum on peripheral components
45 V, 100 ma NPN/PNP general-purpose transistor
Rev. 4 18 February 29 Product data sheet 1. Product profile 1.1 General description NPN/PNP general-purpose transistor pair in a very small SOT363 (SC-88) Surface-Mounted Device (SMD) plastic package.
EVALUATION KIT AVAILABLE Broadband, Two-Output, Low-Noise Amplifier for TV Tuner Applications MAX2130. Maxim Integrated Products 1
9-86; Rev ; 8/ EVALUATION KIT AVAILABLE Broadband, Two-Output, Low-Noise General Description The broadband, low-distortion, low-noise, two-output amplifier performs preamp, loop-out, and buffer functions
L78MxxAB L78MxxAC. Precision 500 ma regulators. Features. Description
L78MxxAB L78MxxAC Precision 500 ma regulators Features Output current to 0.5 A Output voltages of 5; 6; 8; 9; 10; 12; 15; 18; 24 V Thermal overload protection Short circuit protection Output transition
DS1307ZN. 64 x 8 Serial Real-Time Clock
DS137 64 x 8 Serial Real-Time Clock www.maxim-ic.com FEATURES Real-time clock (RTC) counts seconds, minutes, hours, date of the month, month, day of the week, and year with leap-year compensation valid
14-stage ripple-carry binary counter/divider and oscillator
Rev. 8 25 March 2016 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is a with three oscillator terminals (RS, REXT and CEXT), ten buffered outputs (Q3 to
Features. Ordering Information. * Underbar marking may not be to scale. Part Identification
MIC86 Teeny Ultra Low Power Op Amp General Description The MIC86 is a rail-to-rail output, input common-mode to ground, operational amplifier in Teeny SC7 packaging. The MIC86 provides 4kHz gain-bandwidth
INTEGRATED CIRCUITS. 74LVC08A Quad 2-input AND gate. Product specification IC24 Data Handbook. 1997 Jun 30
INTEGRATED CIRCUITS IC24 Data Handbook 1997 Jun 30 FEATURES Wide supply voltage range of 1.2 V to 3.6 V In accordance with JEDEC standard no. 8-1A Inputs accept voltages up to 5.5 V CMOS low power consumption
Quad 2-input NAND Schmitt trigger
Rev. 9 15 December 2015 Product data sheet 1. General description 2. Features and benefits 3. Applications The is a quad two-input NAND gate. Each input has a Schmitt trigger circuit. The gate switches
Low-power configurable multiple function gate
Rev. 7 10 September 2014 Product data sheet 1. General description The provides configurable multiple functions. The output state is determined by eight patterns of 3-bit input. The user can choose the
1.5A Very L.D.O Voltage Regulator LM29150/29151/29152
FEATURES High Current Capability 1.5A Low Dropout Voltage 350mV Low Ground Current Accurate 1% Guaranteed Initial Tolerance Extremely Fast Transient Response Reverse-Battery and "Load Dump" Protection
LM2704 Micropower Step-up DC/DC Converter with 550mA Peak Current Limit
Micropower Step-up DC/DC Converter with 550mA Peak Current Limit General Description The LM2704 is a micropower step-up DC/DC in a small 5-lead SOT-23 package. A current limited, fixed off-time control
Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches
19-2418; Rev ; 4/2 Quad, Rail-to-Rail, Fault-Protected, General Description The are quad, single-pole/single-throw (SPST), fault-protected analog switches. They are pin compatible with the industry-standard
High Common-Mode Rejection. Differential Line Receiver SSM2141. Fax: 781/461-3113 FUNCTIONAL BLOCK DIAGRAM FEATURES. High Common-Mode Rejection
a FEATURES High Common-Mode Rejection DC: 00 db typ 60 Hz: 00 db typ 20 khz: 70 db typ 40 khz: 62 db typ Low Distortion: 0.00% typ Fast Slew Rate: 9.5 V/ s typ Wide Bandwidth: 3 MHz typ Low Cost Complements
HEF4011B. 1. General description. 2. Features and benefits. 3. Ordering information. 4. Functional diagram. Quad 2-input NAND gate
Rev. 6 10 December 2015 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is a quad 2-input NAND gate. The outputs are fully buffered for the highest noise
DATA SHEET. TDA8560Q 2 40 W/2 Ω stereo BTL car radio power amplifier with diagnostic facility INTEGRATED CIRCUITS. 1996 Jan 08
INTEGRATED CIRCUITS DATA SHEET power amplifier with diagnostic facility Supersedes data of March 1994 File under Integrated Circuits, IC01 1996 Jan 08 FEATURES Requires very few external components High
DATA SHEET. TDA1518BQ 24 W BTL or 2 x 12 watt stereo car radio power amplifier INTEGRATED CIRCUITS
INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC01 July 1994 GENERAL DESCRIPTION The is an integrated class-b output amplifier in a 13-lead single-in-line (SIL) plastic power package.
Microprocessor Supervisory Circuits
19-4333; Rev 4; 12/05 Microprocessor Supervisory Circuits General Description The reduce the complexity and number of components required for power-supply monitoring and battery-control functions in microprocessor
SELECTION GUIDE. Nominal Input
www.murata-ps.com NKE Series FEATURES RoHS Compliant Sub-Miniature SIP & DIP Styles 3kVDC Isolation UL Recognised Wide Temperature performance at full 1 Watt load, 40 C to 85 C Increased Power Density
HI-200, HI-201. Features. Dual/Quad SPST, CMOS Analog Switches. Applications. Ordering Information. Functional Diagram FN3121.9
Data Sheet FN3121.9 Dual/Quad SPST, CMOS Analog Switches HI-200/HI-201 (dual/quad) are monolithic devices comprising independently selectable SPST switches which feature fast switching speeds (HI-200 240ns,
DATA SHEET. TDA1510AQ 24 W BTL or 2 x 12 W stereo car radio power amplifier INTEGRATED CIRCUITS
INTEGRATED CIRCUITS DATA SHEET 24 W BTL or 2 x 12 W stereo car radio File under Integrated Circuits, IC01 January 1992 GENERAL DESCRIPTION The is a class-b integrated output amplifier encapsulated in a
PIN CONFIGURATION FEATURES ORDERING INFORMATION ABSOLUTE MAXIMUM RATINGS. D, F, N Packages
DESCRIPTION The µa71 is a high performance operational amplifier with high open-loop gain, internal compensation, high common mode range and exceptional temperature stability. The µa71 is short-circuit-protected
BAS16 series. 1. Product profile. High-speed switching diodes. 1.1 General description. 1.2 Features and benefits. 1.
Rev. 6 4 September 04 Product data sheet. Product profile. General description, encapsulated in small Surface-Mounted Device (SMD) plastic packages. Table. Product overview Type number Package Configuration
If there is any doubt about the results, measurement shall be made within the following limits : Ambient temperature 25±3 Relative humidity 40%~70%
APPROVED : Tin SHEET : 2 of 10 Standard atmospheric conditions Unless otherwise specified, the standard range of atmospheric conditions for making measurement and tests are as follow : Ambient temperature
Programmable Single-/Dual-/Triple- Tone Gong SAE 800
Programmable Single-/Dual-/Triple- Tone Gong Preliminary Data SAE 800 Bipolar IC Features Supply voltage range 2.8 V to 18 V Few external components (no electrolytic capacitor) 1 tone, 2 tones, 3 tones
CA723, CA723C. Voltage Regulators Adjustable from 2V to 37V at Output Currents Up to 150mA without External Pass Transistors. Features.
CA73, CA73C Data Sheet April 1999 File Number 788. Voltage Regulators Adjustable from V to 37V at Output Currents Up to 1mA without External Pass Transistors The CA73 and CA73C are silicon monolithic integrated
1-of-4 decoder/demultiplexer
Rev. 6 1 April 2016 Product data sheet 1. General description 2. Features and benefits 3. Applications The contains two 1-of-4 decoders/demultiplexers. Each has two address inputs (na0 and na1, an active
CD4013BC Dual D-Type Flip-Flop
CD4013BC Dual D-Type Flip-Flop General Description The CD4013B dual D-type flip-flop is a monolithic complementary MOS (CMOS) integrated circuit constructed with N- and P-channel enhancement mode transistors.
PMEG3005EB; PMEG3005EL
Rev. 0 29 November 2006 Product data sheet. Product profile. General description Planar Maximum Efficiency General Application (MEGA) Schottky barrier rectifiers with an integrated guard ring for stress
HIGH SPEED-10 MBit/s LOGIC GATE OPTOCOUPLERS
DESCRIPTION The, /6 single-channel and /6 dual-channel optocouplers consist of a 5 nm AlGaAS LED, optically coupled to a very high speed integrated photodetector logic gate with a strobable output. This
PMEG3015EH; PMEG3015EJ
Rev. 03 13 January 2010 Product data sheet 1. Product profile 1.1 General description Planar Maximum Efficiency General Application (MEGA) Schottky barrier rectifiers with an integrated guard ring for
PMEG2020EH; PMEG2020EJ
Rev. 04 15 January 2010 Product data sheet 1. Product profile 1.1 General description Planar Maximum Efficiency General Application (MEGA) Schottky barrier rectifiers with an integrated guard ring for
Low Phase Noise XO (for HF Fund. and 3 rd O.T.) XIN XOUT N/C N/C OE CTRL N/C (0,0) Pad #9 OUTSEL
Reserved BUF BUF 62 mil Reserved Reserved FEATURES 100MHz to 200MHz Fund. or 3 rd OT Crystal. Output range: 100 200MHz (no multiplication). Available outputs: PECL, or LVDS. OESEL/OECTRL for both PECL
Symbol Parameters Units Frequency Min. Typ. Max. 850 MHz 14.8 16.3 17.8
Product Description Sirenza Microdevices SGC-689Z is a high performance SiGe HBT MMIC amplifier utilizing a Darlington configuration with a patented active-bias network. The active bias network provides
Hardware Documentation. Data Sheet HAL 202. Hall-Effect Sensor. Edition Sept. 18, 2014 DSH000159_002EN
Hardware Documentation Data Sheet HAL 202 Hall-Effect Sensor Edition Sept. 18, 2014 DSH000159_002EN HAL202 Copyright, Warranty, and Limitation of Liability The information and data contained in this document
INTEGRATED CIRCUITS DATA SHEET. TDA7052 1 W BTL mono audio amplifier. Product specification File under Integrated Circuits, IC01
INTEGRATED CIRCUITS DATA SHEET TDA7052 1 W BTL mono audio amplifier File under Integrated Circuits, IC01 July 1994 GENERAL DESCRIPTION The TDA7052 is a mono output amplifier in a 8-lead dual-in-line (DIL)
74HCU04. 1. General description. 2. Features and benefits. 3. Ordering information. Hex unbuffered inverter
Rev. 7 8 December 2015 Product data sheet 1. General description The is a hex unbuffered inverter. Inputs include clamp diodes. This enables the use of current limiting resistors to interface inputs to
3-to-8 line decoder, demultiplexer with address latches
Rev. 7 29 January 2016 Product data sheet 1. General description The is a high-speed Si-gate CMOS device and is pin compatible with low-power Schottky TTL (LSTTL). The is specified in compliance with JEDEC
MM74HC273 Octal D-Type Flip-Flops with Clear
MM74HC273 Octal D-Type Flip-Flops with Clear General Description The MM74HC273 edge triggered flip-flops utilize advanced silicon-gate CMOS technology to implement D-type flipflops. They possess high noise
Wide Bandwidth, Fast Settling Difet OPERATIONAL AMPLIFIER
Wide Bandwidth, Fast Settling Difet OPERATIONAL AMPLIFIER FEATURES HIGH GAIN-BANDWIDTH: 35MHz LOW INPUT NOISE: 1nV/ Hz HIGH SLEW RATE: V/µs FAST SETTLING: 24ns to.1% FET INPUT: I B = 5pA max HIGH OUTPUT
Kit 27. 1W TDA7052 POWER AMPLIFIER
Kit 27. 1W TDA7052 POWER AMPLIFIER This is a 1 watt mono amplifier Kit module using the TDA7052 from Philips. (Note, no suffix.) It is designed to be used as a building block in other projects where a
How To Control A Power Supply On A Powerline With A.F.F Amplifier
INTEGRATED CIRCUITS DATA SHEET Sound I.F. amplifier/demodulator for TV File under Integrated Circuits, IC02 March 1986 GENERAL DESCRIPTION The is an i.f. amplifier with a symmetrical FM demodulator and
VITESSE SEMICONDUCTOR CORPORATION. 16:1 Multiplexer. Timing Generator. CMU x16
Features 16:1 2.488 Gb/s Multiplexer Integrated PLL for Clock Generation - No External Components 16-bit Wide, Single-ended, ECL 100K Compatible Parallel Data Interface 155.52 MHz Reference Clock Frequency