V CC TOP VIEW. f SSO = 20MHz to 134MHz (DITHERED)

Size: px
Start display at page:

Download "V CC TOP VIEW. f SSO = 20MHz to 134MHz (DITHERED)"

Transcription

1 19-013; Rev 1; 10/11 0MHz to 13MHz Spread-Spectrum General Description The is a spread-spectrum clock modulator IC that reduces EMI in high clock-frequency-based, digital electronic equipment. Using an integrated phase-locked loop (PLL), the accepts an input clock signal in the range of 0MHz to 13MHz and delivers a spread-spectrum modulated output clock signal. The PLL modulates, or dithers, the output clock about the center input frequency at a pin-selectable magnitude and dither rate, allowing direct EMI control and optimization. In addition, through an enable pin the dithering can be enabled or disabled for easy comparison of system performance during EMI testing. This same input pin also allows the output to be three-stated. By dithering the system clock, all the address, data, and timing signals generated from this signal are also dithered so that the measured EMI at the fundamental and harmonic frequencies is greatly reduced. This is accomplished without changing clock rise/fall times or adding the space, weight, design time, and cost associated with mechanical shielding. The is provided in an -pin TSSOP package and operates over a full automotive temperature range of -0 C to +15 C. Applications LCD Panels for TVs, Desktop Monitors, and Notebook and Tablet PCs Automotive Telematics and Infotainment Printers Features Modulates a 0MHz to 13MHz Clock with Center Spread-Spectrum Dithering Selectable Spread-Spectrum Modulation Magnitudes of: ±0.5% ±1.0% ±1.5% ±.0% Low 75ps Cycle-to-Cycle Jitter Spread-Spectrum Disable Mode Pin Compatible with Alliance/PulseCore Semiconductor P00 Series Devices Clock Output Disable Low Power Consumption 3.3V Single Voltage Supply -0 C to +15 C Temperature Range Small -Pin TSSOP Package Ordering Information PART TEMP RANGE PIN-PACKAGE E+ -0 C to +15 C TSSOP E+T -0 C to +15 C TSSOP +Denotes a lead(pb)-free/rohs-compliant package. T = Tape and reel. Typical Operating Circuit appears at end of data sheet. Block Diagram Pin Configuration TOP VIEW CLKIN f IN = 0MHz TO 13MHz PLL WITH CENTER- DITHERED SPREAD SPECTRUM SSO f SSO = 0MHz to 13MHz (DITHERED) CLKIN SMSEL1 1 7 CRSEL CRSEL SMSEL1 SMSEL CONFIGURATION DECODE AND CONTROL ENABLE LOGIC SSEN GND SMSEL GND 3 5 SSO SSEN Maxim Integrated Products 1 For pricing, delivery, and ordering information, please contact Maxim Direct at 1--9-, or visit Maxim s website at

2 ABSOLUTE MAXIMUM RATINGS Voltage Range on Relative to GND V to +3.3V Voltage Range on Any Pin Relative to GND V to ( + 0.5V), not to exceed +3.3V Operating Temperature Range...-0 C to +15 C Continuous Power Dissipation (T A = +70 C) TSSOP (derate.1mw/ C above +70 C)...7mW Storage Temperature Range C to +15 C Lead Temperature (soldering, 10s) C Soldering Temperature (reflow)...+0 C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. RECOMMENDED OPERATING CONDITIONS (TA = -0 C to +15 C, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Supply Voltage (Note 1) V 0. x + Input Logic 1 V IH x Input Logic 0 V IL -0.3 V 0V < (Voltage applied to SSEN or Input Logic Open (SSEN, CRSEL) I OPEN ±1 μa CRSEL) < SSO < 0MHz 15 SSO Load C L pf 0MHz SSO < 13MHz 7 CLKIN Frequency f IN 0 13 MHz CLKIN Duty Cycle f INDC 0 0 % DC ELECTRICAL CHARACTERISTICS ( = +3.0V to +3.V, T A = -0 C to +15 C, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS V Supply Current I CC C L = 7pF f IN = 13MHz 15 ma SMSEL1/SMSEL/CLKIN Input Leakage I IL:1 0V < V IN < μa CRSEL/SSEN Input Leakage I IL: 0V < V IN < μa Output Leakage (SSO) I OZ SSEN = open μa Low-Level Output Voltage (SSO) V OL I OL = ma 0. V High-Level Output Voltage (SSO) V OH I OH = -ma. V AC ELECTRICAL CHARACTERISTICS ( = +3.0V to +3.V, T A = -0 C to +15 C, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS SSO Duty Cycle f SSODC Measured at / 0 0 % SSO Rise Time t R C L = 7pF 1 ns SSO Fall Time t F C L = 7pF 1 ns Peak Cycle-to-Cycle Jitter t J T A = -0 C to +5 C, 10,000 cycles 75 ps Power-Up Time t POR (Note ) 50 ms Note 1: All voltages referenced to ground. Currents into the IC are positive and out of the IC are negative. Note : Time between power applied to device and stable output.

3 (T A = +5 C, unless otherwise noted.) SUPPLY CURRENT vs. SUPPLY VOLTAGE 1 SUPPLY CURRENT (ma) 1 CLKIN = 13MHz 10 CLKIN = MHz CLKIN = 0MHz toc01 SUPPLY CURRENT (ma) SUPPLY CURRENT vs. TEMPERATURE CLKIN = 13MHz CLKIN = MHz CLKIN = 33MHz Typical Operating Characteristics toc0 SUPPLY CURRENT (ma) SUPPLY CURRENT vs. FREQUENCY = 3.V = 3.0V toc SUPPLY VOLTAGE (V) TEMPERATURE ( C) FREQUENCY (MHz) DUTY CYCLE vs. TEMPERATURE DUTY CYCLE vs. SUPPLY VOLTAGE SPECTRUM ATTENUATION vs. FREQUENCY AT DIFFERENT DITHER AMPLITUDES DUTY CYCLE (%) CLKIN = MHz toc0 DUTY CYCLE (%) CLKIN = MHz toc05 ATTENUATION (db) ±1.5% ±% ±1% 0.5% 3dB f OUT = 0MHz.5dB db toc f OUT = 0MHz RBW = 10KHz CENTER DITHER TEMPERATURE ( C) SUPPLY VOLTAGE (V) FREQUENCY (MHz) 3

4 PIN NAME FUNCTION 1 CLKIN Clock Input. 0MHz to 13MHz clock input (f IN ). SMSEL1 3 SMSEL GND Ground 5 SSEN SSO Pin Description Spread-Spectrum Magnitude Select Inputs. These digital inputs select the desired spread-spectrum magnitude as shown in the table below. SMSEL SMSEL1 MAGNITUDE SELECTED 0 0 ±.0% 0 1 ±1.5% 1 0 ±1.0% 1 1 ±0.5% Spread-Spectrum Enable. Three-level input to enable/disable spread-spectrum and to three-state the output. 0 = Power-up/spread-spectrum enabled. Open = SSO three-stated. 1 = Power-up/spread-spectrum disabled (not a bypass mode). Spread-Spectrum Clock Output. Outputs a center-dithered spread-spectrum version of the clock input at CLKIN. 7 CRSEL Supply Voltage Clock Range and Dither Rate Select. Three-level input that determines the dither rate. See the Detailed Description section for details. CRSEL CLKIN RANGE DITHER RATE 0 MHz to 13MHz f IN /0 Open 33MHz to 0MHz f IN /10 1 0MHz to 3MHz f IN /51 Detailed Description The modulates an input clock to generate a center-dithered spread-spectrum output. A 0MHz to 13MHz clock is applied to the CLKIN pin. An internal PLL dithers the output clock about its center frequency at a user-selectable magnitude. Spread-Spectrum Dither Magnitude The can generate dither magnitudes up to ±%. The desired magnitude is selected using input pins SMSEL1 and SMSEL as shown in Table 1. Table 1. Spread-Spectrum Dither Magnitude SMSEL SMSEL1 MAGNITUDE 0 0 ±.0% 0 1 ±1.5% 1 0 ±1.0% 1 1 ±0.5% Spread-Spectrum Dither Rate The output spread-spectrum dither rate is determined by the input frequency to maximize EMI reduction and to ensure that the dither rate is always above the audio frequency range. The user must configure CRSEL, based on Table, depending on the input frequency (f IN ) so that the appropriate dither rate is programmed. Table. Spread-Spectrum Dither Rate CRSEL CLKIN RANGE DITHER RATE 0 MHz to 13MHz f IN /0 Open 33MHz to 0MHz f IN /10 1 0MHz to 3MHz f IN /51

5 Spread-Spectrum Enable On power-up, the output clock (SSO) remains three-stated until the internal PLL reaches a stable frequency. The SSEN input can be used to disable the spread-spectrum modulation and to three-state the SSO output. If the SSEN pin is pulled high, the spread-spectrum modulation is turned off, but the device still uses the internal PLL to generate the clock signal at SSO. If the SSEN pin is open, the output is three-stated. Applications Information Power-Supply Decoupling To achieve best results, it is highly recommended that a decoupling capacitor is used on the IC power-supply pins. Typical values of decoupling capacitors are 0.01µF and 0.1µF. Use a high-quality, ceramic, surface-mount capacitor, and mount it as close as possible to the and GND pins of the IC to minimize lead inductance. IF SSEN = 1 f IN + (0.5%, 1.0%, 1.5%, OR.0% OF f IN ) f IN f IN - (0.5%, 1.0%, 1.5%, OR.0% OF f IN ) DITHER AMOUNT (±0.5%, ±1.0%, ±1.5%, OR ±.0%) f SSO 1 DITHER CYCLE RATE CLKIN RANGE (MHz) DITHER RATE TO 13 f IN /0 33 TO 0 f IN /10 0 TO 3 f IN /51 TIME Figure 1. Spread-Spectrum Frequency Modulation Typical Operating Circuit f IN = 0MHz TO 13MHz CLKIN SMSEL1 SMSEL GND CRSEL SSO SSEN f SSO DITHERED DECOUPLING CAPACITOR NOTE: IN THE ABOVE CONFIGURATION WITH SMSEL1, SMSEL, AND SSEN CONNECTED TO GND AS WELL AS CRSEL CONNECTED TO AND SSEN CONNECTED TO GND, THE DEVICE IS CONFIGURED WITH A SPREAD-SPECTRUM MAGNITUDE OF ±.0%, AND ALLOWS A CLKIN BETWEEN 0MHz and 3MHz. Package Information For the latest package outline information and land patterns (footprints), go to Note that a +, #, or - in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. TSSOP H

6 REVISION NUMBER REVISION DATE DESCRIPTION Revision History PAGES CHANGED 0 /07 Initial release 1 10/11 Updated the Absolute Maximum Ratings, Recommended Operating Conditions, and DC Electrical Characteristics; corrected pin number error in the Pin Description; added the Package Information table,, 5 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 10 San Gabriel Drive, Sunnyvale, CA Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products, Inc.

Spread-Spectrum Crystal Multiplier DS1080L. Features

Spread-Spectrum Crystal Multiplier DS1080L. Features Rev 1; 3/0 Spread-Spectrum Crystal Multiplier General Description The is a low-jitter, crystal-based clock generator with an integrated phase-locked loop (PLL) to generate spread-spectrum clock outputs

More information

ICS650-44 SPREAD SPECTRUM CLOCK SYNTHESIZER. Description. Features. Block Diagram DATASHEET

ICS650-44 SPREAD SPECTRUM CLOCK SYNTHESIZER. Description. Features. Block Diagram DATASHEET DATASHEET ICS650-44 Description The ICS650-44 is a spread spectrum clock synthesizer intended for video projector and digital TV applications. It generates three copies of an EMI optimized 50 MHz clock

More information

Features. Modulation Frequency (khz) VDD. PLL Clock Synthesizer with Spread Spectrum Circuitry GND

Features. Modulation Frequency (khz) VDD. PLL Clock Synthesizer with Spread Spectrum Circuitry GND DATASHEET IDT5P50901/2/3/4 Description The IDT5P50901/2/3/4 is a family of 1.8V low power, spread spectrum clock generators capable of reducing EMI radiation from an input clock. Spread spectrum technique

More information

TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER. Features

TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER. Features DATASHEET ICS280 Description The ICS280 field programmable spread spectrum clock synthesizer generates up to four high-quality, high-frequency clock outputs including multiple reference clocks from a low-frequency

More information

MAX14760/MAX14762/MAX14764 Above- and Below-the-Rails Low-Leakage Analog Switches

MAX14760/MAX14762/MAX14764 Above- and Below-the-Rails Low-Leakage Analog Switches 19-652; Rev 1; 8/12 EVALUATION KIT AVAILABLE MAX1476// General Description The MAX1476// analog switches are capable of passing bipolar signals that are beyond their supply rails. These devices operate

More information

DS1220Y 16k Nonvolatile SRAM

DS1220Y 16k Nonvolatile SRAM 19-5579; Rev 10/10 NOT RECOENDED FOR NEW DESIGNS 16k Nonvolatile SRAM www.maxim-ic.com FEATURES 10 years minimum data retention in the absence of external power Data is automatically protected during power

More information

SPREAD SPECTRUM CLOCK GENERATOR. Features

SPREAD SPECTRUM CLOCK GENERATOR. Features DATASHEET ICS7152 Description The ICS7152-01, -02, -11, and -12 are clock generators for EMI (Electro Magnetic Interference) reduction (see below for frequency ranges and multiplier ratios). Spectral peaks

More information

ICS514 LOCO PLL CLOCK GENERATOR. Description. Features. Block Diagram DATASHEET

ICS514 LOCO PLL CLOCK GENERATOR. Description. Features. Block Diagram DATASHEET DATASHEET ICS514 Description The ICS514 LOCO TM is the most cost effective way to generate a high-quality, high-frequency clock output from a 14.31818 MHz crystal or clock input. The name LOCO stands for

More information

Cold-Junction-Compensated K-Thermocoupleto-Digital Converter (0 C to +1024 C)

Cold-Junction-Compensated K-Thermocoupleto-Digital Converter (0 C to +1024 C) 19-2235; Rev 1; 3/02 Cold-Junction-Compensated K-Thermocoupleto-Digital General Description The performs cold-junction compensation and digitizes the signal from a type-k thermocouple. The data is output

More information

Push-Pull FET Driver with Integrated Oscillator and Clock Output

Push-Pull FET Driver with Integrated Oscillator and Clock Output 19-3662; Rev 1; 5/7 Push-Pull FET Driver with Integrated Oscillator General Description The is a +4.5V to +15V push-pull, current-fed topology driver subsystem with an integrated oscillator for use in

More information

1 TO 4 CLOCK BUFFER ICS551. Description. Features. Block Diagram DATASHEET

1 TO 4 CLOCK BUFFER ICS551. Description. Features. Block Diagram DATASHEET DATASHEET 1 TO 4 CLOCK BUFFER ICS551 Description The ICS551 is a low cost, high-speed single input to four output clock buffer. Part of IDT s ClockBlocks TM family, this is our lowest cost, small clock

More information

ICS650-01 SYSTEM PERIPHERAL CLOCK SOURCE. Description. Features. Block Diagram DATASHEET

ICS650-01 SYSTEM PERIPHERAL CLOCK SOURCE. Description. Features. Block Diagram DATASHEET DATASHEET ICS650-01 Description The ICS650-01 is a low-cost, low-jitter, high-performance clock synthesizer for system peripheral applications. Using analog/digital Phase-Locked Loop (PLL) techniques,

More information

Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches

Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches 19-2418; Rev ; 4/2 Quad, Rail-to-Rail, Fault-Protected, General Description The are quad, single-pole/single-throw (SPST), fault-protected analog switches. They are pin compatible with the industry-standard

More information

Spread Spectrum Clock Generator AK8126A

Spread Spectrum Clock Generator AK8126A Features Output Frequency Range: 22.5MHz 32MHz, 45 MHz 64MHz 90MHz 128MHz Configurable Spread Spectrum Modulation: - AKEMD s Original Spread Spectrum Profile - Modulation Ratio: Center Spread: ±0.25%,

More information

ICS379. Quad PLL with VCXO Quick Turn Clock. Description. Features. Block Diagram

ICS379. Quad PLL with VCXO Quick Turn Clock. Description. Features. Block Diagram Quad PLL with VCXO Quick Turn Clock Description The ICS379 QTClock TM generates up to 9 high quality, high frequency clock outputs including a reference from a low frequency pullable crystal. It is designed

More information

EVALUATION KIT AVAILABLE Broadband, Two-Output, Low-Noise Amplifier for TV Tuner Applications MAX2130. Maxim Integrated Products 1

EVALUATION KIT AVAILABLE Broadband, Two-Output, Low-Noise Amplifier for TV Tuner Applications MAX2130. Maxim Integrated Products 1 9-86; Rev ; 8/ EVALUATION KIT AVAILABLE Broadband, Two-Output, Low-Noise General Description The broadband, low-distortion, low-noise, two-output amplifier performs preamp, loop-out, and buffer functions

More information

INTEGRATED CIRCUITS. 74LVC08A Quad 2-input AND gate. Product specification IC24 Data Handbook. 1997 Jun 30

INTEGRATED CIRCUITS. 74LVC08A Quad 2-input AND gate. Product specification IC24 Data Handbook. 1997 Jun 30 INTEGRATED CIRCUITS IC24 Data Handbook 1997 Jun 30 FEATURES Wide supply voltage range of 1.2 V to 3.6 V In accordance with JEDEC standard no. 8-1A Inputs accept voltages up to 5.5 V CMOS low power consumption

More information

4 OUTPUT PCIE GEN1/2 SYNTHESIZER IDT5V41186

4 OUTPUT PCIE GEN1/2 SYNTHESIZER IDT5V41186 DATASHEET IDT5V41186 Recommended Applications 4 Output synthesizer for PCIe Gen1/2 General Description The IDT5V41186 is a PCIe Gen2 compliant spread-spectrum-capable clock generator. The device has 4

More information

Spread Spectrum Clock Generator

Spread Spectrum Clock Generator Spread Spectrum Clock Generator Features Generates a 1x (PCS3P5811), x (PCS3P581) and 4x() low EMI spread spectrum clock of the input frequency Provides up to 15dB of EMI suppression Input Frequency: 4MHz

More information

MM74HC14 Hex Inverting Schmitt Trigger

MM74HC14 Hex Inverting Schmitt Trigger MM74HC14 Hex Inverting Schmitt Trigger General Description The MM74HC14 utilizes advanced silicon-gate CMOS technology to achieve the low power dissipation and high noise immunity of standard CMOS, as

More information

MM74HC273 Octal D-Type Flip-Flops with Clear

MM74HC273 Octal D-Type Flip-Flops with Clear MM74HC273 Octal D-Type Flip-Flops with Clear General Description The MM74HC273 edge triggered flip-flops utilize advanced silicon-gate CMOS technology to implement D-type flipflops. They possess high noise

More information

MM74HC174 Hex D-Type Flip-Flops with Clear

MM74HC174 Hex D-Type Flip-Flops with Clear Hex D-Type Flip-Flops with Clear General Description The MM74HC174 edge triggered flip-flops utilize advanced silicon-gate CMOS technology to implement D-type flipflops. They possess high noise immunity,

More information

LOW POWER SPREAD SPECTRUM OSCILLATOR

LOW POWER SPREAD SPECTRUM OSCILLATOR LOW POWER SPREAD SPECTRUM OSCILLATOR SERIES LPSSO WITH SPREAD-OFF FUNCTION 1.0 110.0 MHz FEATURES + 100% pin-to-pin drop-in replacement to quartz and MEMS based XO + Low Power Spread Spectrum Oscillator

More information

VT-802 Temperature Compensated Crystal Oscillator

VT-802 Temperature Compensated Crystal Oscillator T-802 Temperature Compensated Crystal Oscillator T-802 Description ectron s T-802 Temperature Compensated Crystal Oscillator (TCXO) is a quartz stabilized, CMOS output, analog temperature compensated oscillator,

More information

ABRIDGED DATA SHEET EVALUATION KIT AVAILABLE

ABRIDGED DATA SHEET EVALUATION KIT AVAILABLE EVALUATION KIT AVAILABLE General Description DeepCoverM embedded security solutions cloak sensitive data under multiple layers of advanced physical security to provide the most secure key storage possible.

More information

MM74HCT373 MM74HCT374 3-STATE Octal D-Type Latch 3-STATE Octal D-Type Flip-Flop

MM74HCT373 MM74HCT374 3-STATE Octal D-Type Latch 3-STATE Octal D-Type Flip-Flop 3-STATE Octal D-Type Latch 3-STATE Octal D-Type Flip-Flop General Description The MM74HCT373 octal D-type latches and MM74HCT374 Octal D-type flip flops advanced silicongate CMOS technology, which provides

More information

High-Speed, Low r ON, SPST Analog Switch (1-Bit Bus Switch)

High-Speed, Low r ON, SPST Analog Switch (1-Bit Bus Switch) High-Speed, Low r ON, SPST Analog Switch (1-Bit Bus Switch) DG2301 ishay Siliconix DESCRIPTION The DG2301 is a high-speed, 1-bit, low power, TTLcompatible bus switch. Using sub-micron CMOS technology,

More information

DM74LS191 Synchronous 4-Bit Up/Down Counter with Mode Control

DM74LS191 Synchronous 4-Bit Up/Down Counter with Mode Control August 1986 Revised February 1999 DM74LS191 Synchronous 4-Bit Up/Down Counter with Mode Control General Description The DM74LS191 circuit is a synchronous, reversible, up/ down counter. Synchronous operation

More information

DG2302. High-Speed, Low r ON, SPST Analog Switch. Vishay Siliconix. (1-Bit Bus Switch with Level-Shifter) RoHS* COMPLIANT DESCRIPTION FEATURES

DG2302. High-Speed, Low r ON, SPST Analog Switch. Vishay Siliconix. (1-Bit Bus Switch with Level-Shifter) RoHS* COMPLIANT DESCRIPTION FEATURES High-Speed, Low r ON, SPST Analog Switch (1-Bit Bus Switch with Level-Shifter) DG2302 DESCRIPTION The DG2302 is a high-speed, 1-bit, low power, TTLcompatible bus switch. Using sub-micron CMOS technology,

More information

Fairchild Solutions for 133MHz Buffered Memory Modules

Fairchild Solutions for 133MHz Buffered Memory Modules AN-5009 Fairchild Semiconductor Application Note April 1999 Revised December 2000 Fairchild Solutions for 133MHz Buffered Memory Modules Fairchild Semiconductor provides several products that are compatible

More information

Low-Jitter I 2 C/SPI Programmable Dual CMOS Oscillator

Low-Jitter I 2 C/SPI Programmable Dual CMOS Oscillator eet General Description The DSC2111 and series of programmable, highperformance dual CMOS oscillators utilizes a proven silicon MEMS technology to provide excellent jitter and stability while incorporating

More information

2 TO 4 DIFFERENTIAL PCIE GEN1 CLOCK MUX ICS557-06. Features

2 TO 4 DIFFERENTIAL PCIE GEN1 CLOCK MUX ICS557-06. Features DATASHEET 2 TO 4 DIFFERENTIAL PCIE GEN1 CLOCK MUX ICS557-06 Description The ICS557-06 is a two to four differential clock mux designed for use in PCI-Express applications. The device selects one of the

More information

High-Bandwidth, T1/E1, SPST Analog Switches

High-Bandwidth, T1/E1, SPST Analog Switches 19-3951; Rev 2; 1/7 High-Bandwidth,, SPST Analog Switches General Description The high-bandwidth, low-on-resistance, quad-spst analog switches are designed to serve as integrated protection switches for

More information

Spread Spectrum Clock Generator

Spread Spectrum Clock Generator Spread Spectrum Clock Generator DESCRIPTION is a clock generator for EMI (Electro Magnetic Interference) reduction. The peak of unnecessary (EMI) can be attenuated by making the oscillation frequency slightly

More information

DSC1001. Low-Power Precision CMOS Oscillator 1.8~3.3V. Features. General Description. Benefits. Block Diagram

DSC1001. Low-Power Precision CMOS Oscillator 1.8~3.3V. Features. General Description. Benefits. Block Diagram DSC.8~.V LowPower Precision CMOS Oscillator General Description The DSC is a silicon MEMS based CMOS oscillator offering excellent jitter and stability performance over a wide range of supply voltages

More information

VITESSE SEMICONDUCTOR CORPORATION. 16:1 Multiplexer. Timing Generator. CMU x16

VITESSE SEMICONDUCTOR CORPORATION. 16:1 Multiplexer. Timing Generator. CMU x16 Features 16:1 2.488 Gb/s Multiplexer Integrated PLL for Clock Generation - No External Components 16-bit Wide, Single-ended, ECL 100K Compatible Parallel Data Interface 155.52 MHz Reference Clock Frequency

More information

MAX14759/MAX14761/MAX14763 Above- and Below-the-Rails Low On-Resistance Analog Switches

MAX14759/MAX14761/MAX14763 Above- and Below-the-Rails Low On-Resistance Analog Switches 19-651; Rev ; 9/11 /MX14761/ General Description The /MX14761/ analog switches are capable of passing bipolar signals that are beyond their supply rails. These devices operate from a single +3.V to +5.5V

More information

PECL and LVDS Low Phase Noise VCXO (for 65-130MHz Fund Xtal) XIN XOUT N/C N/C CTRL VCON (0,0) OESEL (Pad #25) 1 (default)

PECL and LVDS Low Phase Noise VCXO (for 65-130MHz Fund Xtal) XIN XOUT N/C N/C CTRL VCON (0,0) OESEL (Pad #25) 1 (default) Reserved BUF BUF 62 mil OESEL^ Reserved Reserved PL520-30 FEATURES 65MHz to 130MHz Fundamental Mode Crystals. Output range (no PLL): 65MHz 130MHz (3.3V). 65MHz 105MHz (2.5V). Low Injection Power for crystal

More information

DS1220Y 16k Nonvolatile SRAM

DS1220Y 16k Nonvolatile SRAM Not Recommended for New Design DS122Y 16k Nonvolatile SRAM www.maxim-ic.com FEATURES years minimum data retention in the absence of external power Data is automatically protected during power loss Directly

More information

DS2187 Receive Line Interface

DS2187 Receive Line Interface Receive Line Interface www.dalsemi.com FEATURES Line interface for T1 (1.544 MHz) and CEPT (2.048 MHz) primary rate networks Extracts clock and data from twisted pair or coax Meets requirements of PUB

More information

EVALUATION KIT AVAILABLE Single-Chip Global Positioning System Receiver Front-End BIAS CBIAS GND GND RFIN GND GND IFSEL

EVALUATION KIT AVAILABLE Single-Chip Global Positioning System Receiver Front-End BIAS CBIAS GND GND RFIN GND GND IFSEL 19-3469; Rev 2; 4/08 EVALUATION KIT AVAILABLE Single-Chip Global Positioning System General Description The complete single-chip global positioning system (GPS) RF front-end utilizes many innovative and

More information

On/Off Controller with Debounce and

On/Off Controller with Debounce and 19-4128; Rev ; 5/8 On/Off Controller with Debounce and General Description The is a pushbutton on/off controller with a single switch debouncer and built-in latch. It accepts a noisy input from a mechanical

More information

CD4013BC Dual D-Type Flip-Flop

CD4013BC Dual D-Type Flip-Flop CD4013BC Dual D-Type Flip-Flop General Description The CD4013B dual D-type flip-flop is a monolithic complementary MOS (CMOS) integrated circuit constructed with N- and P-channel enhancement mode transistors.

More information

3-input EXCLUSIVE-OR gate. The 74LVC1G386 provides a 3-input EXCLUSIVE-OR function.

3-input EXCLUSIVE-OR gate. The 74LVC1G386 provides a 3-input EXCLUSIVE-OR function. Rev. 02 3 September 2007 Product data sheet 1. General description The provides a 3-input EXCLUSIVE-OR function. The input can be driven from either 3.3 or 5 V devices. This feature allows the use of these

More information

AAT3520/2/4 MicroPower Microprocessor Reset Circuit

AAT3520/2/4 MicroPower Microprocessor Reset Circuit General Description Features PowerManager The AAT3520 series of PowerManager products is part of AnalogicTech's Total Power Management IC (TPMIC ) product family. These microprocessor reset circuits are

More information

DALLAS DS1233 Econo Reset. BOTTOM VIEW TO-92 PACKAGE See Mech. Drawings Section on Website

DALLAS DS1233 Econo Reset. BOTTOM VIEW TO-92 PACKAGE See Mech. Drawings Section on Website 5V EconoReset www.maxim-ic.com FEATURES Automatically restarts microprocessor after power failure Monitors pushbutton for external override Internal circuitry debounces pushbutton switch Maintains reset

More information

74AC139 74ACT139 Dual 1-of-4 Decoder/Demultiplexer

74AC139 74ACT139 Dual 1-of-4 Decoder/Demultiplexer Dual 1-of-4 Decoder/Demultiplexer General Description The AC/ACT139 is a high-speed, dual 1-of-4 decoder/ demultiplexer. The device has two independent decoders, each accepting two inputs and providing

More information

DS1225Y 64k Nonvolatile SRAM

DS1225Y 64k Nonvolatile SRAM DS1225Y 64k Nonvolatile SRAM www.maxim-ic.com FEATURES years minimum data retention in the absence of external power Data is automatically protected during power loss Directly replaces 2k x 8 volatile

More information

Low-Cost, Micropower, SC70/SOT23-8, Microphone Preamplifiers with Complete Shutdown

Low-Cost, Micropower, SC70/SOT23-8, Microphone Preamplifiers with Complete Shutdown 9-9; Rev ; 4/ Low-Cost, Micropower, SC7/SOT23-8, Microphone General Description The are micropower op amps optimized for use as microphone preamplifiers. They provide the ideal combination of an optimized

More information

DM74LS153 Dual 1-of-4 Line Data Selectors/Multiplexers

DM74LS153 Dual 1-of-4 Line Data Selectors/Multiplexers Dual 1-of-4 Line Data Selectors/Multiplexers General Description Each of these data selectors/multiplexers contains inverters and drivers to supply fully complementary, on-chip, binary decoding data selection

More information

DM74LS151 1-of-8 Line Data Selector/Multiplexer

DM74LS151 1-of-8 Line Data Selector/Multiplexer 1-of-8 Line Data Selector/Multiplexer General Description This data selector/multiplexer contains full on-chip decoding to select the desired data source. The DM74LS151 selects one-of-eight data sources.

More information

MAAD-007084-0001TB. Digital Attenuator 15.5 db, 5-Bit, TTL Driver, DC-2.0 GHz Rev. V2. Features. Schematic with Off-Chip Components.

MAAD-007084-0001TB. Digital Attenuator 15.5 db, 5-Bit, TTL Driver, DC-2.0 GHz Rev. V2. Features. Schematic with Off-Chip Components. MAAD-007084-00000 5.5, 5-Bit, TTL Driver, DC-2.0 GHz Rev. 2 Features Attenuation: 0.5 Steps to 5.5 Low DC Power Consumption Integral TTL Driver 50 ohm Impedance Test Boards are Available Tape and Reel

More information

DM74LS112A Dual Negative-Edge-Triggered Master-Slave J-K Flip-Flop with Preset, Clear, and Complementary Outputs

DM74LS112A Dual Negative-Edge-Triggered Master-Slave J-K Flip-Flop with Preset, Clear, and Complementary Outputs August 1986 Revised March 2000 DM74LS112A Dual Negative-Edge-Triggered Master-Slave J-K Flip-Flop with Preset, Clear, and Complementary General Description This device contains two independent negative-edge-triggered

More information

R EXT THERMISTOR. Maxim Integrated Products 1

R EXT THERMISTOR. Maxim Integrated Products 1 19-2219; Rev 0; 2/02 Thermistor-to-Digital Converter General Description The converts an external thermistor s temperature-dependent resistance directly into digital form. The thermistor and an external

More information

MM74C150 MM82C19 16-Line to 1-Line Multiplexer 3-STATE 16-Line to 1-Line Multiplexer

MM74C150 MM82C19 16-Line to 1-Line Multiplexer 3-STATE 16-Line to 1-Line Multiplexer MM74C150 MM82C19 16-Line to 1-Line Multiplexer 3-STATE 16-Line to 1-Line Multiplexer General Description The MM74C150 and MM82C19 multiplex 16 digital lines to 1 output. A 4-bit address code determines

More information

256K (32K x 8) Static RAM

256K (32K x 8) Static RAM 256K (32K x 8) Static RAM Features High speed: 55 ns and 70 ns Voltage range: 4.5V 5.5V operation Low active power (70 ns, LL version) 275 mw (max.) Low standby power (70 ns, LL version) 28 µw (max.) Easy

More information

INTEGRATED CIRCUITS. 74F153 Dual 4-line to 1-line multiplexer. Product specification 1996 Jan 05 IC15 Data Handbook

INTEGRATED CIRCUITS. 74F153 Dual 4-line to 1-line multiplexer. Product specification 1996 Jan 05 IC15 Data Handbook INTEGRATED CIRCUITS 1996 Jan 05 IC15 Data Handbook FEATURES Non-inverting outputs Separate enable for each section Common select inputs See 74F253 for 3-State version PIN CONFIGURATION Ea 1 S1 2 I3a 3

More information

400KHz 60V 4A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter

400KHz 60V 4A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter Features Wide 5V to 32V Input Voltage Range Positive or Negative Output Voltage Programming with a Single Feedback Pin Current Mode Control Provides Excellent Transient Response 1.25V reference adjustable

More information

CD4043BC CD4044BC Quad 3-STATE NOR R/S Latches Quad 3-STATE NAND R/S Latches

CD4043BC CD4044BC Quad 3-STATE NOR R/S Latches Quad 3-STATE NAND R/S Latches CD4043BC CD4044BC Quad 3-STATE NOR R/S Latches Quad 3-STATE NAND R/S Latches General Description The CD4043BC are quad cross-couple 3-STATE CMOS NOR latches, and the CD4044BC are quad cross-couple 3- STATE

More information

Link-65 MHz, +3.3V LVDS Transmitter 24-Bit Flat Panel Display (FPD) Link-65 MHz

Link-65 MHz, +3.3V LVDS Transmitter 24-Bit Flat Panel Display (FPD) Link-65 MHz DS90C383A/DS90CF383A +3.3V Programmable LVDS Transmitter 24-Bit Flat Panel Display (FPD) Link-65 MHz +3.3V LVDS Transmitter 24-Bit Flat Panel Display (FPD) Link-65 MHz 1.0 General Description The DS90C383A/DS90CF383A

More information

DS2401 Silicon Serial Number

DS2401 Silicon Serial Number 19-5860; Rev 3/15 Silicon Serial Number BENEFITS AND FEATURES Guaranteed Unique 64-Bit ROM ID Chip for Absolute Traceability o Unique, Factory-Lasered and Tested 64-Bit Registration Number (8-Bit Family

More information

24-Channel Automotive Switch Monitor

24-Channel Automotive Switch Monitor 9-4464; Rev ; 2/9 EVALUATION KIT AVAILABLE 24-Channel Automotive Switch Monitor General Description The is a 24-channel automotive contact monitor designed as an interface between mechanical switches and

More information

LM1036 Dual DC Operated Tone/Volume/Balance Circuit

LM1036 Dual DC Operated Tone/Volume/Balance Circuit LM1036 Dual DC Operated Tone/Volume/Balance Circuit General Description The LM1036 is a DC controlled tone (bass/treble), volume and balance circuit for stereo applications in car radio, TV and audio systems.

More information

DM74LS157 DM74LS158 Quad 2-Line to 1-Line Data Selectors/Multiplexers

DM74LS157 DM74LS158 Quad 2-Line to 1-Line Data Selectors/Multiplexers September 1986 Revised April 2000 DM74LS157 DM74LS158 Quad 2-Line to 1-Line Data Selectors/Multiplexers General Description These data selectors/multiplexers contain inverters and drivers to supply full

More information

DM7474 Dual Positive-Edge-Triggered D-Type Flip-Flops with Preset, Clear and Complementary Outputs

DM7474 Dual Positive-Edge-Triggered D-Type Flip-Flops with Preset, Clear and Complementary Outputs DM7474 Dual Positive-Edge-Triggered D-Type Flip-Flops with Preset, Clear and Complementary Outputs General Description This device contains two independent positive-edge-triggered D-type flip-flops with

More information

The 74LVC1G11 provides a single 3-input AND gate.

The 74LVC1G11 provides a single 3-input AND gate. Rev. 8 17 September 2015 Product data sheet 1. General description The provides a single 3-input AND gate. The input can be driven from either 3.3 V or 5 V devices. This feature allows the use of this

More information

MC10SX1190. Fibre Channel Coaxial Cable Driver and Loop Resiliency Circuit

MC10SX1190. Fibre Channel Coaxial Cable Driver and Loop Resiliency Circuit Fibre Channel Coaxial Cable Driver and Loop Resiliency Circuit Description The MC10SX1190 is a differential receiver, differential transmitter specifically designed to drive coaxial cables. It incorporates

More information

CD4027BC Dual J-K Master/Slave Flip-Flop with Set and Reset

CD4027BC Dual J-K Master/Slave Flip-Flop with Set and Reset October 1987 Revised March 2002 CD4027BC Dual J-K Master/Slave Flip-Flop with Set and Reset General Description The CD4027BC dual J-K flip-flops are monolithic complementary MOS (CMOS) integrated circuits

More information

8-bit binary counter with output register; 3-state

8-bit binary counter with output register; 3-state Rev. 3 24 February 2016 Product data sheet 1. General description The is an 8-bit binary counter with a storage register and 3-state outputs. The storage register has parallel (Q0 to Q7) outputs. The binary

More information

www.jameco.com 1-800-831-4242

www.jameco.com 1-800-831-4242 Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. 19-0028; Rev 3; 9/01 Monolithic CMOS Analog Multiplexers General Description

More information

SN28838 PAL-COLOR SUBCARRIER GENERATOR

SN28838 PAL-COLOR SUBCARRIER GENERATOR Solid-State Reliability Surface-Mount Package NS PACKAE (TOP VIEW) description The SN28838 is a monolithic integrated circuit designed to interface with the SN28837 PALtiming generator in order to generate

More information

3-to-8 line decoder, demultiplexer with address latches

3-to-8 line decoder, demultiplexer with address latches Rev. 7 29 January 2016 Product data sheet 1. General description The is a high-speed Si-gate CMOS device and is pin compatible with low-power Schottky TTL (LSTTL). The is specified in compliance with JEDEC

More information

CAT28C64B F R E E. 64K-Bit CMOS PARALLEL EEPROM L E A D FEATURES DESCRIPTION BLOCK DIAGRAM

CAT28C64B F R E E. 64K-Bit CMOS PARALLEL EEPROM L E A D FEATURES DESCRIPTION BLOCK DIAGRAM 64K-Bit CMOS PARALLEL EEPROM FEATURES Fast read access times: 90/120/150ns Low power CMOS dissipation: Active: 25 ma max. Standby: 100 µa max. Simple write operation: On-chip address and data latches Self-timed

More information

DATA SHEET. TDA8560Q 2 40 W/2 Ω stereo BTL car radio power amplifier with diagnostic facility INTEGRATED CIRCUITS. 1996 Jan 08

DATA SHEET. TDA8560Q 2 40 W/2 Ω stereo BTL car radio power amplifier with diagnostic facility INTEGRATED CIRCUITS. 1996 Jan 08 INTEGRATED CIRCUITS DATA SHEET power amplifier with diagnostic facility Supersedes data of March 1994 File under Integrated Circuits, IC01 1996 Jan 08 FEATURES Requires very few external components High

More information

Maxim Integrated Products 1

Maxim Integrated Products 1 19-542; Rev 1; 5/6 Stereo Volume Control General Description The dual, 4kΩ logarithmic taper volume control features a debounced up/down interface for use with a simple rotary encoder without using a microcontroller

More information

CD4001BC/CD4011BC Quad 2-Input NOR Buffered B Series Gate Quad 2-Input NAND Buffered B Series Gate

CD4001BC/CD4011BC Quad 2-Input NOR Buffered B Series Gate Quad 2-Input NAND Buffered B Series Gate CD4001BC/CD4011BC Quad 2-Input NOR Buffered B Series Gate Quad 2-Input NAND Buffered B Series Gate General Description The CD4001BC and CD4011BC quad gates are monolithic complementary MOS (CMOS) integrated

More information

Features. Instruction. Decoder Control Logic, And Clock Generators. Address Compare amd Write Enable. Protect Register V PP.

Features. Instruction. Decoder Control Logic, And Clock Generators. Address Compare amd Write Enable. Protect Register V PP. February 1999 NM9366 (MICROWIRE Bus Interface) 4096-Bit Serial EEPROM General Description The NM9366 devices are 4096 bits of CMOS non-volatile electrically erasable memory divided into 256 16-bit registers.

More information

74AC191 Up/Down Counter with Preset and Ripple Clock

74AC191 Up/Down Counter with Preset and Ripple Clock 74AC191 Up/Down Counter with Preset and Ripple Clock General Description The AC191 is a reversible modulo 16 binary counter. It features synchronous counting and asynchronous presetting. The preset feature

More information

VS-500 Voltage Controlled SAW Oscillator

VS-500 Voltage Controlled SAW Oscillator VS-500 Voltage Controlled SAW Oscillator Features Improved High Performance ASIC Industry Standard Package, 9 x 14 x 4.5 mm Frequencies from 155 MHz to 850 MHz 3.3 V or 5.0 V Operation At 155.52 MHz, Jitter

More information

DM9368 7-Segment Decoder/Driver/Latch with Constant Current Source Outputs

DM9368 7-Segment Decoder/Driver/Latch with Constant Current Source Outputs DM9368 7-Segment Decoder/Driver/Latch with Constant Current Source Outputs General Description The DM9368 is a 7-segment decoder driver incorporating input latches and constant current output circuits

More information

74VHC574 Octal D-Type Flip-Flop with 3-STATE Outputs

74VHC574 Octal D-Type Flip-Flop with 3-STATE Outputs 74HC574 Octal D-Type Flip-Flop with 3-STATE Outputs General Description Ordering Code: March 1993 Revised May 2005 The HC574 is an advanced high speed CMOS octal flipflop with 3-STATE output fabricated

More information

MM74HC4538 Dual Retriggerable Monostable Multivibrator

MM74HC4538 Dual Retriggerable Monostable Multivibrator MM74HC4538 Dual Retriggerable Monostable Multivibrator General Description The MM74HC4538 high speed monostable multivibrator (one shots) is implemented in advanced silicon-gate CMOS technology. They feature

More information

DATA SHEET. TDA1518BQ 24 W BTL or 2 x 12 watt stereo car radio power amplifier INTEGRATED CIRCUITS

DATA SHEET. TDA1518BQ 24 W BTL or 2 x 12 watt stereo car radio power amplifier INTEGRATED CIRCUITS INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC01 July 1994 GENERAL DESCRIPTION The is an integrated class-b output amplifier in a 13-lead single-in-line (SIL) plastic power package.

More information

Triple-Channel Video Reconstruction Filter and Buffer for Composite and Y/C Outputs

Triple-Channel Video Reconstruction Filter and Buffer for Composite and Y/C Outputs 9-3269; Rev ; 6/5 EVALUATION KIT AVAILABLE Triple-Channel Video Reconstruction Filter and General escription The is a low-cost, triple-channel video reconstruction filter for S-video and CVBS video-signal

More information

1-Mbit (128K x 8) Static RAM

1-Mbit (128K x 8) Static RAM 1-Mbit (128K x 8) Static RAM Features Pin- and function-compatible with CY7C109B/CY7C1009B High speed t AA = 10 ns Low active power I CC = 80 ma @ 10 ns Low CMOS standby power I SB2 = 3 ma 2.0V Data Retention

More information

Cold-Junction Compensated Thermocouple-to-Digital Converter

Cold-Junction Compensated Thermocouple-to-Digital Converter General Description The MAX31855 performs cold-junction compensation and digitizes the signal from a K-, J-, N-, T-, S-, R-, or E-type thermocouple. The data is output in a signed 14-bit, SPI-compatible,

More information

74HC238; 74HCT238. 3-to-8 line decoder/demultiplexer

74HC238; 74HCT238. 3-to-8 line decoder/demultiplexer Rev. 4 27 January 2016 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The decodes three binary weighted address inputs (A0, A1 and A2) to eight mutually exclusive

More information

7 OUT1 8 OUT2 9 OUT3 10 OUT4 11 OUT5 12 OUT6 13 OUT7 14 OUT8 15 OUT9 16 OUT10 17 OUT11 18 OUT12 19 OUT13 20 OUT14 21 OUT15 22 OUT16 OUT17 23 OUT18

7 OUT1 8 OUT2 9 OUT3 10 OUT4 11 OUT5 12 OUT6 13 OUT7 14 OUT8 15 OUT9 16 OUT10 17 OUT11 18 OUT12 19 OUT13 20 OUT14 21 OUT15 22 OUT16 OUT17 23 OUT18 18 CHANNELS LED DRIVER GENERAL DESCRIPTION IS31FL3218 is comprised of 18 constant current channels each with independent PWM control, designed for driving LEDs. The output current of each channel can be

More information

74AC138 74ACT138 1-of-8 Decoder/Demultiplexer

74AC138 74ACT138 1-of-8 Decoder/Demultiplexer 1-of-8 Decoder/Demultiplexer General Description The AC/ACT138 is a high-speed 1-of-8 decoder/demultiplexer. This device is ideally suited for high-speed bipolar memory chip select address decoding. The

More information

Microprocessor Supervisory Circuits

Microprocessor Supervisory Circuits 19-4333; Rev 4; 12/05 Microprocessor Supervisory Circuits General Description The reduce the complexity and number of components required for power-supply monitoring and battery-control functions in microprocessor

More information

74HC377; 74HCT377. 1. General description. 2. Features and benefits. 3. Ordering information

74HC377; 74HCT377. 1. General description. 2. Features and benefits. 3. Ordering information Rev. 4 24 February 2016 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is an octal positive-edge triggered D-type flip-flop. The device features clock (CP)

More information

www.jameco.com 1-800-831-4242

www.jameco.com 1-800-831-4242 Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. www.maxim-ic.com FEATURES 10 years minimum data retention in the absence

More information

AAT4280 Slew Rate Controlled Load Switch

AAT4280 Slew Rate Controlled Load Switch General Description Features SmartSwitch The AAT4280 SmartSwitch is a P-channel MOSFET power switch designed for high-side load switching applications. The P-channel MOSFET device has a typical R DS(ON)

More information

DM74LS169A Synchronous 4-Bit Up/Down Binary Counter

DM74LS169A Synchronous 4-Bit Up/Down Binary Counter Synchronous 4-Bit Up/Down Binary Counter General Description This synchronous presettable counter features an internal carry look-ahead for cascading in high-speed counting applications. Synchronous operation

More information

74HCU04. 1. General description. 2. Features and benefits. 3. Ordering information. Hex unbuffered inverter

74HCU04. 1. General description. 2. Features and benefits. 3. Ordering information. Hex unbuffered inverter Rev. 7 8 December 2015 Product data sheet 1. General description The is a hex unbuffered inverter. Inputs include clamp diodes. This enables the use of current limiting resistors to interface inputs to

More information

74HC154; 74HCT154. 4-to-16 line decoder/demultiplexer

74HC154; 74HCT154. 4-to-16 line decoder/demultiplexer Rev. 7 29 February 2016 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is a. It decodes four binary weighted address inputs (A0 to A3) to sixteen mutually

More information

1-of-4 decoder/demultiplexer

1-of-4 decoder/demultiplexer Rev. 6 1 April 2016 Product data sheet 1. General description 2. Features and benefits 3. Applications The contains two 1-of-4 decoders/demultiplexers. Each has two address inputs (na0 and na1, an active

More information

High-Speed, Low-Power, 3V/5V, Rail-to-Rail, Single-Supply Comparators MAX941/MAX942/ MAX944. General Description. Features. Ordering Information

High-Speed, Low-Power, 3V/5V, Rail-to-Rail, Single-Supply Comparators MAX941/MAX942/ MAX944. General Description. Features. Ordering Information General Description The MAX941/MAX94/ are single/dual/quad highspeed comparators optimized for systems powered from a 3V or 5V supply. These devices combine high speed, low power, and rail-to-rail inputs.

More information

DATA SHEET. TDA1510AQ 24 W BTL or 2 x 12 W stereo car radio power amplifier INTEGRATED CIRCUITS

DATA SHEET. TDA1510AQ 24 W BTL or 2 x 12 W stereo car radio power amplifier INTEGRATED CIRCUITS INTEGRATED CIRCUITS DATA SHEET 24 W BTL or 2 x 12 W stereo car radio File under Integrated Circuits, IC01 January 1992 GENERAL DESCRIPTION The is a class-b integrated output amplifier encapsulated in a

More information

CAN bus ESD protection diode

CAN bus ESD protection diode Rev. 04 15 February 2008 Product data sheet 1. Product profile 1.1 General description in a small SOT23 (TO-236AB) Surface-Mounted Device (SMD) plastic package designed to protect two automotive Controller

More information