RZT42 B&S Intek Page 1 of 45 Carburetor, Air Cleaner And Manifold

Transcription

1 RZT42 B&S Intek Page 1 of 45 Carburetor, Air Cleaner And Manifold

2 RZT42 B&S Intek Page 2 of 45 Carburetor, Air Cleaner And Manifold 1 BS Manifold, Intake 2 BS /P Gasket, Intake 3 BS Stud (Carburetor) 4 BS Screw (Intake Manifold) 5 BS Bushing, Throttle Shaft 6 BS Kit, Idle Mixture 7 BS /P Screw (Throttle Valve) 8 BS Kit, Idle Speed 9 BS /P Pin, Flpat Hinge 10 BS S Valve, Float Needle 11 BS /P Seal, Inlet (LMT697204) BS /P Seal, Inlet (LMT697202) 12 BS Valve, Choke 13 BS Valve, Choke 14 BS Jet, Main (Standard) BS Jet, Main (High Altitude) 15 BS S Carburetor 16 BS Plug, Welch 17 BS Valve, Throttle 18 BS S Kit, Throttle Shaft 19 BS /P Float, Carburetor 20 BS S Gasket, Float Bowl 21 BS S Kit, Choke Shaft 22 BS S Kit, Choke Shaft 23 BS Nozzle, Carburetor 24 BS Connector, Hose 25 BS S Line, Fuel 26 BS /P Sealing Washer 27 BS S Housing, Blower 28 BS Screw (Blower Housing) 29 BS Screw (Blower Housing) 30 BS Elbow, Intake 31 BS S Filter, Air Cleaner Cartridge 32 BS S Clamp, Hose 33 BS O-Ring Seal 34 BS Spring/Seal Assembly 35 BS /P Spring/Seal Assembly 36 BS Retainer, Air Filter 37 BS /P Nut (Carburetor) 38 BS /P Spring, Detent 39 BS Solenoid, Fuel 40 BS /P Screw, Float Bowl 41 BS /P Filter, Pre Cleaner 42 BS Cover, Air Cleaner 43 BS /P Bowl, Float 44 BS /P Seal, Throttle Shaft 45 BS Plate, Trim 46 BS /P Cap, Limiter 47 BS /P O-Ring Seal 48 BS O-Ring Seal 49 BS Latch, Blower Housing

3 RZT42 B&S Intek Page 3 of 45 Controls And Deck Lift

4 RZT42 B&S Intek Page 4 of 45 Controls And Deck Lift S Lever, Lapbar, LH S/F Shaft Assembly, Deck Lift also furnish (2) A S/F Shaft Assembly, Deck Lift also furnish (4) A 1 /P Rod, Deck Front Hanger A 1 Lever, Lapbar, RH S Bracket, Lapbar Pivot S Handle, Brake S/F Arm, Deck Lift, with 1/4" hole /P/F Arm, Deck Lift, with 5/16" hole Bracket, Front Deck Hanger /P Screw, Hex Cap, 3/8-16 x 1.0 GR /P Screw, Hex Lock, 1/4-20 x.62 GR /P Screw, Hex Cap, 5/16-18 x.75 GR /P Screw, Hex Cap, 5/16-18 x 1.75 GR S Ferrule, 3/8-24 x A 2 /P Nut, Hex Flange, 5/ S Nut, Hex Insert Lock, 5/16-18 GR S Nut, Hex Flange Lock, 3/8-16 GRF Nut, Hex Flange Lock, 1/4-28 GR2, use with ref /P Nut, Hex Flange Insert Lock, 5/16-18 GrF, use with ref /P Nut, Hex Jam, 5/8-18 GR S Pin, Internal Cotter /P E-Ring,.625 Dia. Shaft Grip, Handle S Grip, Lapbar Grip, Handle S Spring, Compression S Spring, Extension /P Spring, Torsion S Washer, Lock, 5/ /P Washer, Bell,.265 x.75 x S Washer, Flat,.344 x.688 x /P Washer, Flat,.64 x 1.12 x /P Screw, Shoulder,.498 x.340:3/ Screw, Shoulder, 1/4-28 x.375, use with ref /P Screw, Hex Cap, 5/16-18 x 1.5 GR5, use with ref S Bearing, Hex Flange S Bearing, Flange Snap,.50 ID Cable, Deck Lift, 5.05 Long, also furnish (4) Rod, Brake Rod, Deck Lift Handle S Rod, Lapbar Control S Shaft, Control Hub, Control

5 RZT42 B&S Intek Page 5 of 45 Controls And Deck Lift /P Pin, Internal Cotter Bearing, Flange,.626 x.938 x /P Screw, Hex Cap, 3/8-16 x 1.5 GR5, use with ref 2A /P Nut, Hex Flange Insert Lock, 3/8-16 GrF, use with ref 2A S Nut, Hex Jam, 3/8-16 GR5, use with ref 2A /P Nut, Hex Jam, 5/16-18 GR5, use with ref F Deck Cable Hardware Kit, not shown

6 RZT42 B&S Intek Page 6 of 45 Crankcase, Crankshaft And Piston

7 RZT42 B&S Intek Page 7 of 45 Crankcase, Crankshaft And Piston 1 BS Cylinder Assembly 2 BS /P Kit, Bushing/Seal (Magneto Side) 3 BS S Seal, Oil 4 BS Sump, Engine 5 BS Gasket, Breather 6 BS Screw (Breather Assembly) 7 BS S Tube, Breather 8 BS /P Gasket, Crankcase 9 BS /P Plug, Oil Drain 10 BS Crankshaft 11 BS S Seal, Oil 12 BS /P Screw 13 BS S Key, Flywheel 14 BS S Piston Assembly (Standard) BS Piston Assembly (.020 Oversize) 15 BS /P Ring Set, Piston (Standard) BS Ring Set, Piston (.020 Oversize) 16 BS Lock Ring, Piston Pin 17 BS Pin, Piston (Standard) 18 BS S Rod, Connecting (Standard) BS Rod, Connecting (.020 Undersize) 19 BS S Screw (Connecting Rod) 20 BS /P Slinger, Governor/Oil 21 BS Tappet, Valve 22 BS S Camshaft 23 BS Plug, Oil 24 BS Key, Timing 25 BS Shield, Cylinder 26 BS /P Screw 27 BS S Dipstick 28 BS Seal, Dipstick Tube 29 BS Tube, Dipstick 30 BS Bushing, Governor Lever 31 BS S Cover, Breather Passage 32 BS /P Seal, Governor Shaft 33 BS /P Pin, Locating 34 BS Gear, Timing 35 BS Screw (Oil Pump Cover) 36 BS S Link, Counterweight 37 BS S Counterweight 38 BS Pin, Counterweight 39 BS /P Seal, O-Ring (Dipstick Tube) 40 BS Dipstick/Tube Assembly 41 BS /P O-Ring Seal (Oil Pump Cover) 42 BS Cover, Oil Pump 43 BS Screen, Oil Pump 44 BS S Pump, Oil 45 BS S Filter, Oil 46 BS Shaft, Pump 47 BS Reed, Breather 48 BS Screw 49 BS Plug, AVS Counterweight BS /P Shortblock

8 RZT42 B&S Intek Page 8 of 45 Crankcase, Crankshaft And Piston BS-31G Engine, Replacement

9 RZT42 B&S Intek Page 9 of 45 Cylinder Head

10 RZT42 B&S Intek Page 10 of 45 Cylinder Head 1 BS S Head, Cylinder 2 BS S Gasket, Cylinder Head 3 BS /P Screw, Cylinder Head 4 BS S Valve, Exhaust 5 BS S Valve, Intake 6 BS /P Spring, Valve 7 BS S Retainer, Valve 8 BS Tappet, Valve 9 BS /P Adjuster, Rocker Arm 10 BS /P Cap, Valve /P Spark Plug (RC12YC) 12 BS O-Ring Seal (Intake Manifold) 13 BS /P Boot, Spark Plug 14 BS /P Stud, Rocker Arm 15 BS /P Seal, Valve 16 BS /P Screw (Rocker Cover) 17 BS S Gasket, Rocker Cover 18 BS S Cover, Rocker 19 BS /P Rod, Push (Intake) BS /P Rod, Push (Exhaust) 20 BS /P Arm, Rocker 21 BS /P Guide, Push Rod

11 RZT42 B&S Intek Page 11 of 45 Electrical

12 RZT42 B&S Intek Page 12 of 45 Electrical /P Screw, Hex Wash. Hd. Tapp, 1/4-20 x /P Screw, Hex Cap, 1/4-20 x.75 GR /P Nut, Hex Sems, 1/ S Key Strap, Battery Hook, Wire Rectangular S Switch, Ignition A 1 S Meter, Hour S Switch, Dbl. Pole - Neutral S Solenoid D 1 S Battery, 245 CCA S Switch, PTO S Switch, Snap Mount (N.C.) - Reverse Switch, 3-Pole, (NC-NO-NO) - Brake Harness Assembly, Wire Not Shown Jumper Harness, Neutral Not Shown Cable Wire, Red - Starter Not Shown Cable Wire, Black - to Ground Not Shown S Cable Wire, Red - Solenoid Not Shown

13 RZT42 B&S Intek Page 13 of 45 Engine Connections

14 RZT42 B&S Intek Page 14 of 45 Engine Connections S Tube, Exhaust S Tank, Fuel, 3.0 Gal B 1 S Cap, Fuel Not shown S Bracket, Muffler Mounting Shield, Muffler Tube Heat /P Screw, Hex Wash. Hd. Tapp #8-18 x /P Screw, Hex Cap, 7/16-20 x 4.0 GR /P Screw, Hex Wash. Hd. Tapp 1/4-20 x /P Screw, Hex Wash. Hd. Tapp 5/16-12 x Screw, Hex Wash. Hd. Tapp #12-16 x A 2 /P Screw, Socket Hd. 5/16-18 x /P Screw, Hex Wash. Hd. Tapp 3/8-16 x /P Screw, Hex Cap, 5/16-18 x.75 GR /P Screw, Truss Hd. Mach. #8-32 x /P Nut, Hex, # S Nut, Hex Insert Lock, 5/16-18 GR S/F Clutch Assembly, Electric PTO, (GT1-JD08) S/F Clutch Assembly, Electric PTO, (GT1A-MT-09) S Gasket, Exhaust (272293) /P Knob, Throttle Control S Washer, Lock, 7/ /P Washer, Flat,.438 x 1.75 x Fitting, Elbow S Cable, Throttle, 39.0 Lg Wire, Tank Mounting S Hose, Fuel Line Cut to approx. 9 inches /P Clamp, Hose Not shown A 1 S Deflector, Muffler A 1 S Muffler S Valve, Oil Drain S Hose, Oil Drain Extension Cap, Oil Drain Valve A 1 /P Pulley, Drive, 3.25 Dia Key, Square, 1/4 x 2.25, use with PTO Clutch /P Key, Square, 1/4 x 1.5, use with PTO Clutch /P Nut, Hex Sems, 1/ Clip, Cable Retainer S/F Anti-rotation Bracket, units with Mfg Code B095G - E135G Not shown, use with

15 RZT42 B&S Intek Page 15 of 45 Flywheel And Electrical

16 RZT42 B&S Intek Page 16 of 45 Flywheel And Electrical 1 BS /P Flywheel 2 BS Guard, Flywheel 3 BS Screen, Rotating 4 BS Screw (Rotating Screen) 5 BS /P Screw (Flywheel Guard) 6 BS S Switch, Oil Pressure 7 BS /P Armature, Magneto 8 BS Screw (Armature) 9 BS Wire, Stop 10 BS /P Alternator 11 BS S Regulator 12 BS Screw (Regulator) 13 BS Gear, Pinion 14 BS Harness, Wiring 15 BS Terminal, Spark Plug 16 BS S Fan, Flywheel 17 BS Screw (Flywheel) 18 BS /P Ring, Retaining 19 BS Kit, Screw/Washer 20 BS S Screw (Flywheel Fan) 21 BS S Screw (Alternator)

17 RZT42 B&S Intek Page 17 of 45 Frame And Drive Idler Assembly

18 RZT42 B&S Intek Page 18 of 45 Frame And Drive Idler Assembly S Frame Assembly 777D /P Graphic, Cub Cadet A 1 S Idler Arm, Drive /P Screw, Hex Cap, 3/8-16 x 1.5 GR S Nut, Hex Flange Lock, 3/-16 GRF /P Nut, Hex Lock, 7/16-14 GRA Spring, Extension,.75 x S Washer, Flat,.406 x.875 x /P Washer, Flat,.45 x 1.25 x.164 HT S Fitting, Lube, 3/16 Drive Pulley, Idler, 4.08 Dia A 1 S Screw, Shoulder,.68 x 1.59

19 RZT42 B&S Intek Page 19 of 45 Front Axle

20 RZT42 B&S Intek Page 20 of 45 Front Axle A 2 Bracket, Castor Wheel Axle, Front Pivot /P Wheel Assembly, 11.0 x 4.0 x Bearing, Flange Not Shown S Bearing, Roller Not Shown /P Screw, Hex Lock, 1/2-13 x 1.25 GR /P Screw, Hex Cap, 1/2-20 x 5.5 GR /P Screw, Hex Cap, 3/8-16 x 1.0 GR S Shaft, Axle S Nut, Hex Lock, 1/2-20 GRA S Bearing, Flange, 1.0 x S Washer, Lock, 3/ S Washer, Flat,.39 x 1.5 x /P Washer, Flat, 1.0 x 1.75 x S Fitting, Lube, 3/16 Drive S Spacer,.79 x A 2 /P Spacer, Wheel

21 RZT42 B&S Intek Page 21 of 45 Fuel System And Controls

22 RZT42 B&S Intek Page 22 of 45 Fuel System And Controls 1 BS S Line, Fuel 2 BS /P Screw (Control Bracket) 3 BS /P Link, Mechanical Governor 4 BS S Spring, Governor 5 BS /P Link, Choke 6 BS /P Bracket, Control 7 BS Control Lever, Governor 8 BS /P Spring, Governor Link 9 BS /P Filter, Fuel 10 BS Screw (Fuel Pump) 11 BS Screw (Fuel Pump) 12 BS /P Pump, Fuel 13 BS Washer 14 BS Nut (Governor Control Lever) 15 BS Shield, Cable 16 BS Bolt (Governor Control Lever) 17 BS S Clamp, Hose 18 BS S Pin, Cotter 19 BS /P Crank, Governor 20 BS S Hose, Vacuum

23 RZT42 B&S Intek Page 23 of 45 Mower Deck 42 Inch

24 RZT42 B&S Intek Page 24 of 45 Mower Deck 42 Inch Arm, Idler Bracket, Deck Lift Housing, Deck 777S /P Graphic, Danger 777S /P Graphic, Danger 777I S Graphic, Instruction S Spindle Assembly Pulley /P Screw, Hex Cap, 3/8-16 x 1.75 GR /P Screw, Hex Cap, 5/16-18 x 1.25 GR /P Screw, Hex Wash. Hd. Tapp 1/4-20 x /P Screw, Hex Wash. Hd. Tapp 5/16-18 x /P Screw, Hex Wash. Hd. Tapp 5/16-12 x /P Screw, Hex Cap, 1/4-20 x.62 GR /P Screw, Hex Cap, 5/16-18 x 1.75 GR S Pin, Grass Catcher, 1/ /P Nut, Hex Insert Lock, 1/4-20 GR A 2 /P Nut, Hex Flange, 5/ S Nut, Hex Insert Lock, 5/16-18 GR S Nut, Hex Flange, 3/8-16 GRF /P Nut, Hex, 1/4-20 GR S Nut, Hex, 5/16-18 GR S Pin, Cotter, 1/8 x B 1 S Gear, Deck Adjustment /P Nut, Push,.25 x B 1 S Chute Assembly, Discharge 777S S Graphic, Danger B 2 /P Cover, Belt S Spring, Compression S Spring, Extension,.94 Dia. x S Wheel, Deck Ball, S Washer, Lock, 5/ /P Washer, Bell,.265 x.75 x S Fitting, Lube, 3/16 Drive S Screw, Shoulder,.498 x 1.53:3/ A 1 S Screw, Shoulder,.68 x /P/F Blade, Hi-Lift, A 2 /P/F Blade, 3 in 1, /P Rod, Deck Hanger S Belt, V, Type A Sec x B 1 S Pulley, Idler, 3.5 Dia Pulley, Idler, 4.06 Dia A 1 S Skirt, Deck /P Washer, Flat,.38 x.93 x.11 HT B 1 S Nozzle, Deck Water S Nut, Hex, M S Washer, Lock, S Adapter, Water Nozzle

25 RZT42 B&S Intek Page 25 of 45 Operator's Platform

26 RZT42 B&S Intek Page 26 of 45 Operator's Platform B 1 Frame, Seat Box (Two expansion cup holes) Mfg.code B075 & before Frame, Seat Box (One expansion cup holes) Mfg.code B075 & before 777I S Graphic, Park Brake 777S S Graphic, Warning 777I S Graphic, Deck Height Bracket, Foot Rest 777D /P Graphic, Cub Cadet A 2 /P Bracket, Console Mounting Bracket, Switch Mounting Screw, Hex Wash. Hd Tapp #12-16 x /P Screw, Hex Wash. Hd. Tapp. 1/4-20 x A 20 /P Screw, Hex Wash. Hd. Tapp 5/16-18 x /P Screw, Hex Wash. Hd. Tapp. 1/4-20 x /P Screw, Hex Wash. Hd Tapp #10-16 x /P Screw, Hex Cap, 3/8-16 x 1.25 GR A 2 /P Screw, Shoulder,.625 x.175:3/ Nut, U Type Speed, 1/ S Nut, Hex Jam, 1/4-20 GR S Nut, Hex Insert Lock, 5/16-18 GR S Nut, Hex Flange Lock, 3/8-16 GRF A 2 /P Knob, 3/8-16: S Switch, Seat, Snap Mount, N.C A 1 S Console, LH 777I S Graphic, Instruction 777D S Graphic, Cub Cadet 777I S Graphic, Throttle Control Console, RH 777I S Graphic, Instruction 777D S Graphic, Cub Cadet /P Spring, Switch Actuator Pad, Seat S Washer, Flat HT,.395 x.87 x S Screw, Shoulder,.437 x.268: 5/ S Seat 777D /P Graphic, Cub Cadet 777D /P Graphic, USA Bracket, Seat Pivot Pad, Abrasive Foot Plate Pad, Abrasive Toe Plate Screw, Shoulder,.50 x.685:3/8-16 Mfg code L164 & after S Washer, Flat,.406 x.875 x.059

27 RZT42 B&S Intek Page 27 of 45 Rear Drive And Wheels

28 RZT42 B&S Intek Page 28 of 45 Rear Drive And Wheels A 2 S Rod, Bypass Transmission Assembly, RH, Service Kit replaces A NLA /P Neutral Return Spring Included in service kit, not shown, must have the same color neutral return spring on RH & LH transmission A 1 S Transmission, RH Double D axle Transmission Assembly, LH, Service Kit replaces A NLA /P Neutral Return Spring Included in service kit, not shown, must have the same color neutral return spring on RH & LH transmission A 1 S Transmission, LH Double D axle Wheel Assembly, 18 x 6.5 x /P Tire, 18 x 6.5 x S Valve Assembly /P Screw, Hex Cap, 5/16-18 x 2.75 GR Screw, Hex Lock, 7/16-14 x 2.25 GR /P Stud, Rib Neck, 7/16-14 x /P Screw, Hex Cap, 5/16-18 x 2.25 GR /P Screw, Hex Cap, 5/16-18 x 2.0 GR Brace, Transmission S Nut, Hex Insert Lock, 5/16-18 GR A 6 /P Nut, Hex Flange Lock, 5/16-18 GR /P Nut, Lug, 7/ /P Nut, Hex Lock, 9/16-18 GRC S Pin, Internal Cotter S Washer, Flat,.344 x.688 x S Hub, Wheel S Hub, Wheel Double D Included in service kit, not shown S V-Belt, Type A Sec x /P Reservoir, Expansion, Mfg code A195 & Before (2 single tanks) use with A & A S Reservoir, Expansion, Mfg code A205 & After (1 single tank design) use with A & A /P Screw, Hx Wash, Hd. Tapp, 1/4-20 x.5, Mfg code A195 & Before /P Screw, Hex Cap, 1/4-20 x.75 GR5, Mfg code A205 & After Clamp, Hose 22 1 Hose, Hydraulic, 54 inches Nut, U-Type Speed, 1/4-20, Mfg code A205 & After /P SCREW:3/8"-16 x.750:gr5:lock Included in service kit, not shown

29 RZT42 B&S Intek Page 29 of 45 Rear Drive And Wheels CLAMP:HOSE:.750 Included in service kit, not shown S WASHER:FLAT:.390 x 1.50 x.134 Included in service kit, not shown HOSE:BREATHER Included in service kit, not shown

30 RZT42 B&S Intek Page 30 of 45 Service Kits

31 RZT42 B&S Intek Page 31 of 45 Service Kits 1 BS S Seal, Oil 2 BS S Gasket, Cylinder Head 3 BS Gasket, Breather 4 BS /P Gasket, Crankcase 5 BS S Seal, Oil 6 BS /P Gasket, Intake 7 BS Bushing, Throttle Shaft 8 BS /P Screw, Throttle Valve 9 BS /P Pin, Float Hinge 10 BS S Valve, Float Needle 11 BS /P Seal, Inlet (LMT ) BS /P Seal, Inlet (LMT ) 12 BS Jet, Main 13 BS /P Kit, Carburetor Overhaul 14 BS S Gasket, Float Bowl 15 BS Nozzle, Carburetor 16 BS /P Sealing Washer 17 BS S Gasket Set, Engine 18 BS Seal, Dipstick Tube 19 BS O-Ring Seal 20 BS Spring/Seal Assembly 21 BS /P Spring/Seal Assembly 22 BS /P Seal, Governor Shaft 23 BS /P Seal, O-Ring 24 BS /P Seal, Valve 25 BS /P O-Ring Seal 26 BS S Set, Carburetor Gasket 27 BS /P Seal, Throttle Shaft 28 BS S Gasket, Rocker Cover 29 BS S Gasket Set, Valve 30 BS /P O-Ring Seal 31 BS O-Ring Seal

32 RZT42 B&S Intek Page 32 of 45 Starter Motor

33 RZT42 B&S Intek Page 33 of 45 Starter Motor 1 BS /P Motor, Starter 2 BS Screw (Starter Motor) 3 BS /P Brush Set 4 BS Washer (Brush Retainer) 5 BS /P Strap, Starter 6 BS Drive, Starter 7 BS /P Clutch, Drive 8 BS /P Armature, Starter 9 BS Nut (Starter Cable) 10 BS S Screw (Drive Cap) 11 BS Clip, Wire 12 BS Clip, Wire 13 BS Gear, Pinion 14 BS Nut (Brush Retainer) 15 BS Cap, Drive 16 BS /P Cap, End 17 BS Housing, Starter 18 BS /P Ring, Retaining 19 BS /P Retainer, Brush

34 RZT42 B&S Intek Page 34 of 45 Transmission LH

35 RZT42 B&S Intek Page 35 of 45 Transmission LH 1 HG-70862L 1 /P Housing Assembly, Main LH 2 HG-70863L 1 /P Side Assembly, RH 3 HG Plate, Bypass 4 HG /P Block Assembly 5 piston 4 HG /P Block Assembly 7 piston 5 HG Spacer,.32 x HG /P Plug, SAE #6 7 HG /P Pin, Stainless 8 HG /P Screw, Hex Self Tapping, 1/4-20 x HG S Seal, Lip,.625 x 1.0 x HG Bolt, Hex Flange, 3/8-24 x HG Seal, Lip,.375 x.75 x HG /P Ring, Retaining,.375 Ext. 13 HG Rod, Bypass 14 HG Ring, Retaining,.75 Int. 15 HG Arm, Bypass 16 HG /P Ring, Retaining,.375 Push 17 HG /P Swashplate, Trunnion 18 HG /P Seal, Lip, 18 x 32 x 7 19 HG S Washer, Flat, 11/32 x 7/8 x 1/16 20 HG /P Screw, 5/16-24 x HG /P Spring, Compression 22 HG /P Washer,.591 x.787 x HG /P Shaft, Input 24 HG Bearing, Ball, 17mm x 40 x HG /P Ring, Wire Retaining, HG /P Spacer 27 HG /P Seal, Lip, 17 x 40 x 7 28 HG /P Ring, Retaining 29 HG S Bearing, Thrust, 30 x 52 x HG /P Washer, Flat, 5/8 x 1.0 x HG Ring, Retaining 32 HG Gear, Pinion, 13T 33 HG Shaft, Motor 34 HG Washer,.71 x 1.16 x HG /P Washer, HT,.5 x 1.0 x HG Gear, 10T/48T 37 HG /P Gear, Jackshaft, 10T 38 HG Pin, Jackshaft 39 HG /P Ring, Spiral Retaining 40 HG S Gear, Bull, 52T 41 HG /P Washer, 3/4 x 1.5 x HG /P Bearing, Sleeve 43 HG S Axle Taper Spline 44 HG /P Bushing,.752 x x HG /P Seal, Lip,.75 x x N/A 1 Kit, Fan-Pulley (furnish components) 48 HG /P Kit, Brake Arm 49 HG-70864L 1 /P Kit, Center Section-Filter RH 50 HG Kit, Bypass Arm 51 HG S Kit, Filter 52 HG /P Disc, Brake Cog 53 HG Fan, 6" 10 Blade

36 RZT42 B&S Intek Page 36 of 45 Transmission LH 54 HG /P Pulley Kit, HG S Nut, Hex Insert Lock, 1/ HG /P Screw, Hex Wash. Hd. Tapp 1/ HG /P Fitting/O-ring Assembly 59 HG S Screw, Patch, 5/16-24 x HG Bushing, Pilot, HG Washer, Plastic 62 HG Washer, 1.5 x.34 x HG S Spring, Extension 64 HG Kit, Return Assembly RH HG /P Kit, Seal HG /P Sealant, Tube Not shown

37 RZT42 B&S Intek Page 37 of 45 Transmission LH DD axle

38 RZT42 B&S Intek Page 38 of 45 Transmission LH DD axle 1 HG-70862L 1 /P Housing Assembly, Main LH. 2 HG-70863L 1 /P Side Assembly, LH 3 HG Plate, Bypass 4 HG /P Pump Block Assembly 5 HG Spacer,.32 x HG /P Motor Block Assembly 7 HG /P Plug, SAE #6 8 HG /P Pin, Stainless 9 HG /P Screw, Hex Self Tapping,1/4-20 x HG S Seal, Brake 11 HG Bolt, Hex Flange, 3/8-24 x HG Seal, Lip,.375 x.75 x HG /P Ring, Retaining,.375 Ext. 14 HG Rod, Bypass 15 HG Ring, Retaining,.75 Int. 16 HG Arm, Bypass 17 HG /P Ring, Retaining,.375 Push 18 HG /P Swashplate, Trunnion 19 HG /P Seal, Lip, 18 x 32 x 7 20 HG Arm, Control LH 21 HG S Washer, Flat, 11/32 x 7/8 x 1/16 22 HG /P Screw, 5/16-24 x HG /P Spring, Compression 24 HG /P Washer,.591 x.787 x HG /P Shaft, Input 26 HG Bearing, Ball, 17mm x 40 x HG /P Ring, Wire Retaining, HG /P Spacer 29 HG /P Seal, Lip, 17 x 40 x 7 30 HG /P Ring, Retaining 31 HG S Bearing, Thrust, 30 x 52 x HG /P Washer, Flat, 5/8 x 1.0 x HG Ring, Retaining 34 HG Gear, Pinion, 13T 35 HG Shaft, Motor 36 HG Washer,.71 x 1.16 x HG /P Washer, HT,.5 x 1.0 x HG Gear, 10T/48T 39 HG /P Gear, Jackshaft, 10T 40 HG Pin, Jackshaft 41 HG Ring, Spiral Retaining 42 HG Gear, Bull, 52T 43 HG Washer, x x HG Bearing, Sleeve 45 HG Shaft, Axle, 1.0 x 11.7 Double-D 46 HG /P Bushing, Axle 47 HG /P Seal, Lip, 1.0 x 1.57 x HG-70868L 1 Kit, Expansion Plate, LH 49 HG S Kit, Fan-Pulley 50 HG /P Kit, Brake Arm 51 HG Kit, Center Section-Filter LH 52 HG Kit, Bypass Arm 53 HG /P Kit, Filter

39 RZT42 B&S Intek Page 39 of 45 Transmission LH DD axle 54 HG /P Disc, Brake Cog 55 N/A 1 Hub, Pulley furnish HG HG S Fan, 7" 10 Blade 57 N/A 1 Pulley, 4.5 furnish HG HG S Nut, Hex Insert Lock, 1/ HG Washer, OD Slotted 60 HG /P Kit, Breather 61 HG S Screw, Hx Patch, 5/16-24 x HG Washer, 1.5 x.34 x /P Spring, Extension replaces HG-51833, RH & LH transmissions must have the same color return spring 64 HG Kit, Return AssemblyLH 65 HG Arm, Neutral RH 66 HG Assemble, Return, Bi-Direct. 67 HG /P Fitting, w/cap Used only on Transmissions w/ Breather Hose Hose Assembly Breather-Used Only with Transmissions Before Mfg. Date A267 HG HG /P 1 /P Kit, Seal not shown Sealant Tube, 10.3 oz not shown

40 RZT42 B&S Intek Page 40 of 45 Transmission RH

41 RZT42 B&S Intek Page 41 of 45 Transmission RH 1 HG-70862R 1 /P Housing Assembly, Main RH 2 HG-70863R 1 /P Side Assembly, RH 3 HG Plate, Bypass 4 HG /P Block Assembly 5 piston 4 HG /P Block Assembly 7 piston 5 HG Spacer,.32 x HG /P Plug, SAE #6 7 HG /P Pin, Stainless 8 HG /P Screw, Hex Self Tapping, 1/4-20 x HG S Seal, Lip,.625 x 1.0 x HG Bolt, Hex Flange, 3/8-24 x HG Seal, Lip,.375 x.75 x HG /P Ring, Retaining,.375 Ext. 13 HG Rod, Bypass 14 HG Ring, Retaining,.75 Int. 15 HG Arm, Bypass 16 HG /P Ring, Retaining,.375 Push 17 HG /P Swashplate, Trunnion 18 HG /P Seal, Lip, 18 x 32 x 7 19 HG S Washer, Flat, 11/32 x 7/8 x 1/16 20 HG /P Screw, 5/16-24 x HG /P Spring, Compression 22 HG /P Washer,.591 x.787 x HG /P Shaft, Input 24 HG Bearing, Ball, 17mm x 40 x HG /P Ring, Wire Retaining, HG /P Spacer 27 HG /P Seal, Lip, 17 x 40 x 7 28 HG /P Ring, Retaining 29 HG S Bearing, Thrust, 30 x 52 x HG /P Washer, Flat, 5/8 x 1.0 x HG Ring, Retaining 32 HG Gear, Pinion, 13T 33 HG Shaft, Motor 34 HG Washer,.71 x 1.16 x HG /P Washer, HT,.5 x 1.0 x HG Gear, 10T/48T 37 HG /P Gear, Jackshaft, 10T 38 HG Pin, Jackshaft 39 HG /P Ring, Spiral Retaining 40 HG S Gear, Bull, 52T 41 HG /P Washer, 3/4 x 1.5 x HG /P Bearing, Sleeve 43 HG S Axle Taper Spline 44 HG /P Bushing,.752 x x HG /P Seal, Lip,.75 x x N/A 1 Kit, Fan-Pulley (furnish components) 48 HG /P Kit, Brake Arm 49 HG-70864R 1 /P Kit, Center Section-Filter RH 50 HG Kit, Bypass Arm 51 HG S Kit, Filter 52 HG /P Disc, Brake Cog 53 HG Fan, 6" 10 Blade

42 RZT42 B&S Intek Page 42 of 45 Transmission RH 54 HG /P Pulley, HG S Nut, Hex Insert Lock, 1/ HG /P Screw, Hex Wash. Hd. Tapp 1/ HG /P Fitting/O-ring Assembly 59 HG S Screw, Patch, 5/16-24 x HG Bushing, Pilot, HG Washer, Plastic 62 HG Washer, 1.5 x.34 x HG S Spring, Extension 64 HG Kit, Return Assembly RH HG /P Kit, Seal HG /P Sealant, Tube Not shown

43 RZT42 B&S Intek Page 43 of 45 Transmission RH DD axle

44 RZT42 B&S Intek Page 44 of 45 Transmission RH DD axle 1 HG-70862R 1 /P Housing Assembly, Main RH 2 HG-70863R 1 /P Side Assembly, RH 3 HG Plate, Bypass 4 HG /P Pump Block Assembly 5 HG Spacer,.32 x HG /P Motor Block Assembly 7 HG /P Plug, SAE #6 8 HG /P Pin, Stainless 9 HG /P Screw, Hex Self Tapping, 1/4-20 x HG S Seal, Brake 11 HG Bolt, Hex Flange, 3/8-24 x HG Seal, Lip,.375 x.75 x HG /P Ring, Retaining,.375 Ext. 14 HG Rod, Bypass 15 HG Ring, Retaining,.75 Int. 16 HG Arm, Bypass 17 HG /P Ring, Retaining,.375 Push 18 HG /P Swashplate, Trunnion 19 HG /P Seal, Lip, 18 x 32 x 7 20 HG /P Arm, Control RH 21 HG S Washer, Flat, 11/32 x 7/8 x 1/16 22 HG /P Screw, 5/16-24 x HG /P Spring, Compression 24 HG /P Washer,.591 x.787 x HG /P Shaft, Input 26 HG Bearing, Ball, 17mm x 40 x HG /P Ring, Wire Retaining, HG /P Spacer 29 HG /P Seal, Lip, 17 x 40 x 7 30 HG /P Ring, Retaining 31 HG S Bearing, Thrust, 30 x 52 x HG /P Washer, Flat, 5/8 x 1.0 x HG Ring, Retaining 34 HG Gear, Pinion, 13T 35 HG Shaft, Motor 36 HG Washer,.71 x 1.16 x HG /P Washer, HT,.5 x 1.0 x HG Gear, 10T/48T 39 HG /P Gear, Jackshaft, 10T 40 HG Pin, Jackshaft 41 HG Ring, Spiral Retaining 42 HG Gear, Bull, 52T 43 HG Washer, x x HG Bearing, Sleeve 45 HG Shaft, Axle, 1.0 x 11.7 Double-D 46 HG /P Bushing, Axle 47 HG /P Seal, Lip, 1.0 x 1.57 x HG-70868R 1 Kit, Expansion Plate, RH 49 HG S Kit, Fan-Pulley 50 HG /P Kit, Brake Arm 51 HG Kit, Center Section-Filter RH 52 HG Kit, Bypass Arm 53 HG /P Kit, Filter

45 RZT42 B&S Intek Page 45 of 45 Transmission RH DD axle 54 HG /P Disc, Brake Cog 55 1 Hub, Pulley furnish HG HG S Fan, 7" 10 Blade 57 1 Pulley, HG S Nut, Hex Insert Lock, 1/ HG Washer, OD Slotted 60 HG /P Kit, Breather 61 HG S Screw, Hx Patch, 5/16-24 x HG Washer, 1.5 x.34 x /P Spring, Extension replaces HG-51833, RH & LH transmissions must have the same color return spring 64 HG Kit, Return Assembly RH 65 HG Arm, Neutral RH 66 HG Assemble, Return, Bi-Direct. 67 HG /P Fitting, w/cap Used only on Transmissions w/ Breather Hose Hose Assembly Breather-Used Only with Transmissions Before Mfg. Date A267 HG HG /P 1 /P Kit, Seal not shown Sealant Tube, 10.3 oz not shown