B12.12 salto safe 4128 B12. Tilt-turn windows

Transcription

1 B12 Tilt-turn windows B12.12 salto safe Waregemstraat Zulte - Belgium - T F commercial@sobinco.com -

2 salto safe 4128 Contents 1. General characteristics... B Base set n 4028 in combination with SALTO B Vertical centre locking sets n , B Horizontal centre locking sets n , B Reinforcement set n B Handles... B Ordering tables... B General information... B b

3 salto Safe General characteristics To make your windows extra secure against burglary, you should use the high security system SALTO SAFE 4028 in combination with the standard tilt-turn system SALTO The following sets are used dependent on the window dimensions: base set n 4028 for: vent width Fb= mm and vent height Fh= mm page B vertical centre locking set n for vent height Fh= mm.. page B vertical centre locking set n for vent height Fh= mm.. page B horizontal centre locking set n for vent width Fb= mm.. page B horizontal centre locking set n for vent width Fb= mm.. page B The set contains the following high security parts: stainless steel mushroom head bolts pre-riveted to zinc alloy connection pieces, which are connected to the SALTO components and rods in the vent section. zinc alloy security wedges which are fixed on the frame section with clamping plates and self-drilling screws. protection pieces close to the handle and bottom bolt. The reinforcement set n must always be installed (see page B ). The high security set should always be operated by a cylinder locking handle, available in 4 types (see page B ). For windows with vent width Fb= mm you must install the additional arm n The additional arm provides greater stability, especially for wide and heavy windows in tilt position. The additional arm is non-handed. All parts are made of non-corroding materials. Size range: vent width: mm vent height: mm vent weight: max. 130 kg ratio of vent width Fb / vent height Fh = max. 1.5 Special dimensions on request! This system is suitable for sections with frame groove width of 14 mm. See drawing. b

4 salto safe Base set n 4028 in combination with SALTO 4108 Vent width Fb = mm Vent height Fh = mm X = Fb-368 (4108A without A.. when Fb= ) X = Fb-503 (4108A) X = Fb-660 (4108B) For a left window: cut off piece n A or 4108B SALTO SAFE corner transmission A locking point B locking point C locking point E locking point B connection piece nut B safety piece locking point connection piece thickness piece wedge 10 M5x12 screw DIN 965 Installation high security wedge n Slide in clamping plate before the assembly of the frame Screw the plate to the wedge Screw the wedge after positioning b

5 salto Safe Vertical centre locking sets n , Vent height Vent height Fh = mm Fh = mm or locking point locking point wedge A locking point C locking point connection piece wedge locking point locking point wedge A locking point locking point connection piece wedge b

6 salto safe Horizontal centre locking sets n , Vent width Fb = mm C locking point wedge Vent width Fb = mm locking point wedge A locking point wedge b

7 salto Safe 4128 Vent width Fb = mm locking point wedge A locking point wedge additional arm In combination with the SALTO 4108B, the high security set is installed together with the additional arm n for windows with vent width Fb = mm. 5. Reinforcement set n For high security windows you must reinforce the top hinge with the reinforcement set n The M4x10 thread forming screws must fix into at least 6 mm of aluminium. Drilling jig n is available for drilling the holes. Reinforcement set n reinforcement piece screw b

8 salto safe Handles throw X = 34 mm throw X = 34 mm n CYL n The high security system must always be operated by cylinder locking handles n CYL. The cylinder locking handle can be locked in closed or tilt position. The same handles can also be used for side hung windows. As a result, tilt-turn windows and side hung windows can be used next to one another with the advantage of having the same appearance. Finish: handle n CYL and n : grip in aluminium and base in zinc alloy, always polyester powder coated (more than 450 RAL colours). handle n CYL and n CYL: grip and base in aluminium anodised or polyester powder coated (more than 450 RAL colours). Fixing holes see page B throw X = 34 mm throw X = 34 mm n CYL n CYL b

9 salto Safe Ordering tables Fb= Fb= Fb= Fb= Fb= Fh = Fh = Fh = A 4108A Order example: A tilt-turn window with overall vent width (Fb) 1450 mm and overall vent height (Fh) 1600 mm in which glass has a thickness of 16 mm and a weight of 40 kg/m 2. Note: to determine the precise vent weight see page B Fittings to order: 1x 1x 4108B 1x x x x x x b

10 salto safe General information The high security system SALTO SAFE 4028 can be used within the Fh/Fb sizes and weight limitations indicated on the chart below. The ratio of the dimensions Fb/Fh must not exceed the value of 1.5. The handle height should not be less than 1/3 of the vent height. Technical advise should be sought when the sizes of your window are not shown in the chart. High security wedges must be fixed on the frame section with clamping plates and self-drilling screws. Stainless steel mushroom head bolts must be adjusted so that they run free within the security wedge. For heavy, wide windows and especially for vents over 1400 mm wide the additional arm is recommended for good stability of the window in the tilt position. High security wedges or High security system SALTO SAFE 4028 is made of noncorroding materials. The set should not be installed in corrosive atmospheres. Sobinco cannot be held responsible for the malfunctioning of the high security system SALTO SAFE 4028 if any non- Sobinco parts are used. Surface treatment of vent and frame must take place before assembly of the set, as this will affect the working of the gear. Glazing must be in accordance with national standards. The window and gear should be kept clean and lubricated in accordance with our maintenance instructions (copy available on request). Glass thickness without air gap Vent height Fh Vent width Fb max. 130 kg mm kg/m² b