CC-810 KIT SERIES INSTRUCTION SHEET
|
|
- Violet Banks
- 7 years ago
- Views:
Transcription
1 (COMPLETE KIT ILLUSTRTED. CUT-OUTS IN TRCK & FSCI TO EXPOSE COMPONENTS) CC-810 KIT SERIES INSTRUCTION SHEET CROWDERTRCK S CTCH N CLOSE TM SYSTEM PREVENTS BOUNCING ND SLMMING OF SLIDING DOORS. CN BE INSTLLED ON BOTH OPENING ND CLOSING ENDS OF DOORS S NRROW S 18 WIDE. CYCLE TESTED UP TO 50,000 TIMES UP TO 300LBS DOORS USING THE CC-810 WITH CC-3. PRTS LIST (FOR STNDRD CC-810 1KIT) CC-904 TOP MOUNT TRCK X LENGTH (1) (LENGTH = 2 X DOOR WIDTH, EXMPLE: 36 [914MM] DOOR = 72 [1829MM] TRCK) CC-810 INDIVIDUL PRTS LIST (WHEN DISSSEMBLED) CC-810 ZERO CLERNCE CTCH N CLOSE HNGER (2) (COMPLETE SSEMBLY) C-811 U -HOUSING (1) (INCLUDED IN ECH SSEMBLY) C-812 H -BR (1) (INCLUDED IN ECH SSEMBLY) C-818 DJUSTMENT WRENCH (1) CC-813 HNGER BODY (1) (C/W WHEELS. INCLUDED IN ECH SSEMBLY) C-814 HNGER STUD (1) (INCLUDED IN ECH SSEMBLY) C-819 5/32 llen Key (1) CC-2 OR CC-3 CTCH N CLOSE CLOSING DEVICE (2) (SEE DETILS IN INSTRUCTION STEPS) C-815 END CP (1) (INCLUDED IN ECH SSEMBLY) C-817 END CP BOLT (1) (INCLUDED IN ECH SSEMBLY) C-816 SFETY LOCK BOLT (1) (INCLUDED IN ECH SSEMBLY) CTCH N CLOSE IN-TRCK STOPS (2) #10 X 1-1/2 SELF DRILLING SCREWS (4) #10 X 1-3/4 FLTHED SCREWS (14) ELEVTION VIEW OF COMPLETE INSTLLTION C-913 FLOOR GUIDE (1) C-914 GUIDE CHNNEL X LENGTH (1) (LENGTH = DOOR WIDTH, EXMPLE: 36 [914MM] DOOR = 36 [914MM] GUIDE CHNNEL) CTIVTED SIDE RETRCTED SIDE SEE RIGHT MINIMUM 5 5/8 in [142.9 mm] TO CENTER OF HNGER BOLT PRODUCT OF K.N. CROWDER MFG. INC K.N. Crowder Mfg. Inc Burloak Drive Burlington, Ontario, Canada L7L 6B3 K.N. Crowder Inc. 210 Eighth Street South Lewiston, New York TOLL-FREE PHONE: KNC (1562) TOLL-FREE FX: WEBSITE: EMIL: customerservice@kncrowder.com 2014 K.N. CROWDER MFG. INC. ll Rights Reserved.
2 HNGER DJUSTMENT 3 [88.9 mm] MIN CC-810 HNGER WITH CC-904 TRCK MX DETIL 1 [38.1 mm] [OPTIONL CC-940 SNP-ON FSCI ILLUSTRTED S SOLID BLCK PROFILE. CN BE USED ON BOTH SIDES OF THE TRCK OR ONE SIDE ONLY] SET BCK REQUIRED FOR CC-815 END CP (SME ON OPPOSITE END) IN-TRCK STOP CC-X CTCH N CLOSE HNGER DJUSTMENT [4.8 mm] MX 9/16 in [14.3 mm] 1 C H in HIGH mm] CESSED OR 1/4 in 8.0 mm] /2 in mm] STEP #1: DETERMINE DOOR SIZE, HEDER HEIGHT & TRCK POSITION BSED ON SHOW IN THE DETIL 4 1/4 VIEWS in BOVE ND CLERNCE REQUIRED BELOW THE DOOR USING [108.0 THE mm] C-914/C-913 DIMENSION IN-TRCK DETILS. STOP STEP #2: NOTE: IF CCESS TO THE ENDS OF THE TRCK IS NOT VILBLE, STEPS #3&4 MUST BE COMPLETED BEFORE STEP #2. CUT CC-904 LUMINUM TRCK TO SIZE IF REQUIRED (TYPICLLY 2 X THE [75.8 mm] DOOR WIDTH). LOCTE ND PRE-DRILL S THROUGH THE CENTER OF THE TRCK FOR SECURING TO THE STRUCTURL SUPPORT. SECURE TRCK TO STRUCTURL SUPPORT/HEDER. NOTE: STRTING LOCTIONS T ECH END OF THE TRCK SHOULD BE 1/2 FROM CC-X CTCH N CLOSE END ND THEN 19 FROM THE FIRST. THIS WILL PREVENT INTERFERENCE WITH THE CTCH N CLOSE INSTLLTION (SEE ILLUSTRTION BELOW). MINIMUM 3 1/2 # SCREWS HNGER OR 1/4 DJUSTMENT STRUCTURL BOLTS RECOMMENDED TO SECURE [88.9 mm] THE TRCK. MIN MX 1 [38.1 mm] SOLID BCKING IS REQUIRED ND SPCING IS RECOMMENDED TO BE BETWEEN ON CENTER. CONSULT STRUCTURL ENGINEER TO ENSURE DEQUTE SUPPORT & FSTENING. LONG IGH SUGGESTED STRTING LOCTIONS ECH END OF TRCK (IN ORDER TO NOT INTERFERE WITH CTCH'N'CLOSE INSTLLTION) FIG. 4 - SLIDE THE C-812 H -BR OUT OF THE C-811 U -HOUSING. FIG. 5 - HNGER SSEMBLY. CC-X CTCH N CLOSE FIG. 2 FIG. 1 IN-TRCK STOP HNGER DJUSTMENT MIN MX 1 [38.1 mm] IN-TRCK STOP IN-TRCK STOP STEP #3: DISSSEMBLE THE FOR COMPLETE CC-810 ZERO CLERNCE LONG CTCH N CLOSE HNGERS S PER BELOW: FIG. LONG 1 - REMOVE C-817 END CP BOLT WITH THE SUPPLIED LLEN KEY FIG. 2 - REMOVE C-815 END CP FIG. 3 - LOOSENING THE C-816 SFETY LOCK BOLT BUT DO NOT REMOVE SET BCK REQUIRED FOR CC-815 END CP (SME ON OPPOSITE END) D P E END) SET BCK REQUIRED FOR CC-815 END CP (SME ON OPPOSITE END) SET BCK REQUIRED FOR CC-815 END CP (SME ON OPPOSITE END) FOR FIG. 5 FOR FOR FIG. 3 FIG. 4 H STEP #4: SLIDE 2 3/8 THE in TWO CC-810 HNGER SSEMBLIES (FIG.5 FROM STEP #3) INTO [60.1 THE mm] TRCK S SHOWN BELOW. NOTE: THE [76.2 CC-810 mm] HVE TRIGGERS BUILT 1 1/2 INTO in THE HNGER. WHEN INSTLLING, THE [38.1 mm] TRIGGERS MUST BE ORIENTED S SHOWN IN THE ILLUSTRTION DISTNCE BELOW. THE TRIGGER FROM WLLMUST BE CLOSEST TO THE END OF THE TRCK. TO CENTER INSERT THE OF DOORCTCH N CLOSE IN-TRCK STOPS T 3 ECH 5/32 inend FTER THE HNGERS [80.3 mm] DETILHVE BEEN PLCED INTO THE TRCK. NOTE: LEVE THE STOP SCREWS LOOSE TO LLOW THE STOPS TO SLIDE FREELY WITHIN THE TRCK. THE RUBBER BUMPERS OF ECH STOP SHOULD FCE INWRD (TOWRD THE MIDDLE OF THE TRCK ). 4 13/16 in [122.2 mm] LEFT END OF TRCK 1 HIGH [68.3 mm] RIGHT END OF TRCK DETIL [60.1 mm] 1 TRIGGER LOCTIONS [38.1 mm] BUMPER LOCTIONS DISTNCE SEE FIGURE BOVE FROM WLL FOR PROPER INSTLLTION. TO CENTER!!!WRNING!!! OF DOOR 3 5/32 in [75.9 mm] [80.3 mm] IF HNGER BODIES 1 3/8 ND in STOPS RE NOT INSTLLED S SHOWN BOVE, SYSTEM WILL NOT FUNCTION PROPERLY. STEP #5: PREPRE DOOR TO RECEIVE C-811 U -HOUSING FLUSH WITH THE TOP EDGE OF THE DOOR. SLOTS MUST BE 10 [ /16 mm] in LONG, 1-1/8 WIDE ND HNGER 1-3/8 DEEP. SEE ILLUSTRTION [122.2 mm] BELOW DJUSTMENT FOR MORE DETILS. [4.8 mm] MX 9/16 in [68.3 mm] [14.3 mm] 1 WIDE LONG STEP #6: PREPRE BOTTOM OF DOOR FOR C-914 GUIDE CHNNEL & INSTLL. SEE C-913/C-914 INSTRUCTION SHEET OPTION #1 FOR FULL INSTLLTION DETILS. PRODUCT OF K.N. CROWDER MFG. INC K.N. CROWDER MFG. INC. ll Rights Reserved. SET BCK REQUIRED OVERLL HEIGHT 31/32 in [24.4 mm] 1 1/4 in [31.7 mm] MINIMUM 3/8 in [9.5 mm] FOR 2 [63.5 mm] MINIMUM DOOR 29/32 in [22.9 mm] C
3 STEP #7: PLCE C-811 U -HOUSING INTO SLOT CRETED IN STEP #5 WITH TOWRDS THE CENTER OF THE DOOR. HOUSING MUST BE SET 1/8 FROM THE EDGE OF DOOR IN ORDER TO CCOMMODTE C-815 END CP (SEE ILLUSTRTION IN STEP 12 FOR DETILS). SECURE TO DOOR WITH #10 X 1-3/4 FLTHED SCREWS (5) REPET FOR OPPOSITE END OF DOOR. STEP #12: INSTLL C-815 END CPS WITH THE LOWER ENGGING THE IN THE BOTTOM OF THE C-811 U -HOUSING. SECURE END CP WITH C-817 END CP BOLT BY USING C-819 LLEN KEY. SET BCK REQUIRED FOR CC-815 END CP (SME ON OPPOSITE END) STEP #8: LOCTE ND INSTLL C-913 GUIDE ROLLER DIRECTLY BELOW TRCK, CENTER OF DOOR TRVEL. PREPRE ND INSTLL OTHER OPTIONL PRODUCTS T THIS TIME SUCH S CUP OR FLUSH PULLS, DOOR HNDLES, LOCKS, ETC. STEP #9: RISE THE DOOR ND POSITION OVER THE C-913 GUIDE ROLLER. SLIDE THE C-812 H -BR INTO THE C-811 U -HOUSINGS PREVIOUSLY INSTLLED ON THE DOORS. NOTE: THREDED END MUST FCE OUTWRD. THE SQURE BSE OF THE C-814 HNGER STUD MUST BE LIGNED WITH THE LOWER GUIDE CHNNEL SLOT OF THE C-811 U -HOUSING. THE PURPOSE OF THIS SQURE BSE IS TO PREVENT ROTTION OF THE BOLT THEREFORE SECURING THE HEIGHT DJUSTMENT. REPET STEP FOR OPPOSITE END OF DOOR. STEP #13: FTER THE DOOR HS BEEN INSTLLED, POSITION DOOR PPROXIMTELY 5-10 WY FROM THE FINL POSITION T ONE END (USING THE LEFT SIDE S N EXMPLE TO SHOW THIS STEP). PUSH THE LOOSE LEFT SIDE STOP (INSTLLED IN STEP #4) GINST THE HNGER BODY S SHOWN BELOW: STEP #14: WITH THE STOP LOOSE, SLIDE THE DOOR TO THE LEFT TO THE FINL/DESIRED POSITION OF THE DOOR S SHOWN BELOW: STEP #15: ONCE THE FINL POSITION IS CHIEVED, SLIDE THE DOOR WY FROM THE STOP (SLIDE TO THE RIGHT IN THIS EXMPLE). LOCK THE STOP IN POSITION BY TIGHTENING THE TWO CP SCREWS ON THE STOP WITH 3/16 LLEN KEY ( IS SECURED BY FRICTION FIT). STEP #10: TO DJUST DOOR HEIGHT ND PLUMB, SLIDE C-812 H -BR OUT OF C-811 U -HOUSING ND DJUST C-814 HNGER STUD WITH C-818 DJUSTMENT WRENCH. REPET UNTIL REQUIRED HEIGHT ND PLUMB IS CHIEVED. SUGGESTED STRTING LOCTIONS ECH END OF TRCK (IN ORDER TO NOT INTERFERE WITH CTCH'N'CLOSE INSTLLTION) STEP #16: REPET STEPS #13 THRU #15 FOR OPPOSITE SIDE. NOTE: RE-CHECK FINL DOOR POSITIONS GINST THE SECURED STOPS BEFORE PROCEEDING TO STEP #17. RE-DJUST IF REQUIRED. STEP #17: BEFORE INSTLLING THE CTCH N CLOSE DEVICE, PLESE ENSURE IT IS IN THE RETRCTED POSITION. IF IT IS NOT IN THIS POSITION, SLIDE IT DOWN UNTIL IT LOCKS INTO THIS POSITION S SHOWN BELOW. NOTE: THIS WILL REQUIRE SIGNIFICNT FINGER PRESSURE. RETRCTED POSITION ID END # STEP #11: ONCE DJUSTMENTS HVE BEEN FINLIZED, SECURE C-816 SFETY BOLT WITH C-818 DJUSTMENT WRENCH. NOTE: THIS CUSTOM BOLT HS BEEN MNUFCTURED TO ENGGE PRE-DRILLED POSITION IN THE C-811 U -HOUSING IN ORDER TO PREVENT CCIDENTL DISENGGEMENT. IMPORTNT CTCH N CLOSE CLOSING DEVICE NOTES: IF THE DOORS RE 200LBS OR LESS, PLESE ENSURE THE CC-2 CTCH N CLOSE CLOSING DEVICE IS BEING USED. IF THE DOORS RE MINIMUM 200LBS UP TO 300LBS, PLESE ENSURE THE CC-3 CTCH N CLOSE CLOSING DEVICE IS BEING USED. IF THE INCORRECT CTCH N CLOSE CLOSING DEVICE IS USED, THERE IS HIGHER RISK OF FILURE, NOT PROVIDING ENOUGH STRENGTH ND/OR TOO MUCH RESISTNCE IS EXPERIENCED WHEN OPERTING THE DOOR. PRODUCT OF K.N. CROWDER MFG. INC K.N. CROWDER MFG. INC. ll Rights Reserved.
4 SUGGESTED STRTIN (IN ORDER TO NOT INTERF SUGGESTED STRTING LOCTIONS ECH END OF TRCK (IN ORDER TO NOT INTERFERE WITH CTCH'N'CLOSE INSTLLTION) [482 STEP #18: INSTLL THE CTCH N CLOSE CLOSING DEVICE INTO THE TRCK WITH THE SOLID END (ID END # SHOWN ON PREVIOUS PGE) RESTING GINST THE TOP BUMPER ON THE STOPS INSTLLED PREVIOUSLY. NOTE: ENSURE THT THE FSTENERS SECURING TRCK TO HEDER RE NOT PRESENT IN RE WHERE THE CTCH N CLOSE CLOSING DEVICE IS TO BE INSTLLED. IF SO, REMOVE ND RELOCTE TO PROVIDE CLER MOUNTING RE FOR DEVICE. WHEN THE CTCH N CLOSE CLOSING DEVICE IS RESTING TIGHT GINST THE TOP BUMPER OF THE STOP, IT IS IN THE CORRECT POSITION ND WILL CLOSE THE DOOR TO THE DESIRED POSITION. SEE ILLUSTRTION BELOW: ID END # END VIEW OPTIONL PRODUCTS: CC-941 End Cap only (For use with CC-904 Track only) CC-940 Snap-On Fascia IN-TRCK STOP C-102HD Floor Stop CC-942 End Cap only (For use with CC-904 Track & one (1) [76.2 CC-940 mm] Fascia combination only) TCH N CLOSE SIDE VIEW (TRCK SHOWN WITH CUTOUT) 3 [88.9 ID END mm] # HNGER DJUSTMENT MIN MX RETRCTED 1 [38.1 POSITION mm] SNP-ON POINT (SME FOR BOTTOM) STEP #19: SECURE CTCH N CLOSE CLOSING DEVICE TO TRCK WITH #10 X 1-1/2 SELF DRILLING SCREWS. DO THE SME FOR THE OPPOSITE END WITH THE CTCH N CLOSE CLOSING DEVICE INSTLLED IN REVERSE S SHOWN ON THE FRONT PGE IN THE ELEVTION VIEW OF COMPLETE INSTLLTION ILLUSTRTION. NOTE: DO NOT USE IMPCT DRIVER TO SECURE CTCH N CLOSE CLOSING DEVICES TO THE TRCK. DO NOT OVERTIGHTEN SCREWS. TO ESE INSTLLTION, IT IS RECOMMENDED TO PRE-DRILL TRCK WITH 5/32 DRILL BIT. IT IS RECOMMENDED TO SECURE THE FIRST SCREW (CLOSEST TO THE END VIEW STOP), TEST SYSTEM [108.0 BY mm] SLIDING THE DOOR TO IN-TRCK STOP CTIVTE THE CTCH N CLOSE. IF IT IS IN THE CORRECT POSITION, SECURE WITH SECOND SCREW. REMOVE NY DRILL FILLINGS FROM INSIDE THE TRCK S THIS WILL FFECT THE OPERTION OF THE SLIDING DOOR SYSTEM. For Door Locks & Pulls, see pages in the K.N. Crowder Sliding Door Track & Hardware Catalogue SNP-ON POINT (SME FOR BOTTOM) OPTIONL CC-940 FSCI & CC-942/CC-943 END CP INSTLLTION SNP-ON POINT SNP-ON POINT (SME FOR BOTTOM) STEP #1: CUT CC-940 FSCI TO CORRECT LENGTH IF REQUIRED. TYPICLLY FSCI IS SME LENGTH S TRCK PREVIOUSLY INSTLLED. STEP #2: LIFT FSCI UP TO TRCK ND SNP-ON S SHOWN BELOW. REPET FOR OPPOSITE SIDE IF NECESSRY. CC-943 End Cap only (For use with CC-904 Track & two (2) CC-940 Fascia combination only) SNP-ON POINT M) HNGER STEP #3: DJUSTMENT INSTLL CC-942 OR CC-943 END CPS S SNP-ON POINT STEP #20: (SME FOR BOTTOM) TEST THE COMPLETE CTCH N CLOSE SYSTEM BY SLIDING THE DOOR [4.8 mm] SHOWN TO THE RIGHT WITH THE SUPPLIED #8 SCREWS 1 (3 1/8 OR in MX 9/16 in 4 SCREWS PER END CP CTCH N CLOSE TO BOTH LEFT ND RIGHT TO CTIVTE THE CLOSING DEVICES. DETIL [14.3 mm] PROVIDED). NOTE: DO NOT INSTLL SNP-ON POINT TROUBLESHOOTING: WITH IMPCT DRIVER ISSUE: IF THE DOOR IS NOT ENGGING THE CLOSING DEVICE. SOLUTION: ) ENSURE HNGERS RE CORRECTLY ORIENTED. SEE STEP #4. B) ENSURE THE CTCH N CLOSE IS IN THE RETRCTED POSITION PRIOR TO SLIDING THE DOOR CLOSED/OPEN. SEE STEP #17. ISSUE: CHTTER/NOISE WHEN DOOR IS SLIDING. SOLUTION: ENSURE THERE RE NO LUMINUM SHVINGS WITHIN THE TRCK. SHVINGS CN BECOME EMBEDDED IN NYLON TIRES ND CUSE NOISY OPERTION. ISSUE: REPLCING THE CTCH N CLOSE DEVICE. CC-942 END CP SOLUTION: THE CTCH N CLOSE TRCK ND HRDWRE SYSTEM HS BEEN DESIGNED FOR ESY INSTLLTION. SIMPLY REMOVE THE TWO SCREWS THT HOLD THE CTCH N CLOSE IN PLCE ND REPLCE THE CC-943 END CP DEVICE WITH NEW ONE IF FILURE OCCURS. PRODUCT OF K.N. CROWDER MFG. INC K.N. CROWDER MFG. INC. ll Rights Reserved. OPTIONL CC-941 END CP INSTLLTION: INSTLL [60.3 CC-941 mm] END CP S SHOWN TO THE BELOW WITH THE SUPPLIED #8 SCREWS (2 SCREWS PER END CP PROVIDED). NOTE: DO NOT INSTLL WITH IMPCT DRIVER SNP-ON POINT (SME FOR BOTTOM) SNP-ON POINT
5 C-913/C-913-2/C-914 PRTS LIST C-914 GUIDE CHNNEL C-913 BLL BERING ROLLER GUIDE GUIDE SYSTEM INSTRUCTION SHEET C DOUBLE BLL BERING ROLLER GUIDE 2-1/2" [63.5 mm] 4" #10 X 1-1/2" FLTHED [101.6 mm] 1-1/4" SCREWS (4 PER C-913) [31.8 mm] TYPICL INSTLLTION LOCTION FOR FLOOR GUIDES: GUIDE CHNNEL WITH GUIDE ON FLOOR FOR POCKET PPLICTIONS 1-1/2" [38.1 mm] #10 X 1-1/2" FLTHED SCREWS (4 PER C-913-2) TYPICL INSTLLTION LOCTION FOR FLOOR GUIDES: GUIDE CHNNEL WITH GUIDE ON FLOOR FOR BRN DOOR PPLICTIONS OPENED POSITION OPENED POSITION DOOR POCKET TYPICL MINIMUM OVERLP IN POCKET: 2" [50.8 mm] DOOR OPENING CLOSED POSITION WLL WHERE DOOR OPENS TO TYPICL MINIMUM OVERLP OF DOOR ON WLL: 2" [50.8 mm] DOOR OPENING CLOSED POSITION NOTE: IF USING THE C GUIDE, THE TYPICL MINIMUM OVERLP IS 4" [101.6 mm] NOTE: IF USING THE C GUIDE, THE TYPICL MINIMUM OVERLP IS 4" [101.6 mm] OPTION 1: GUIDE CHNNEL WITH GUIDE ON FLOOR M 1-3/8" 29/32" [23 mm] 3/8" MIN [9.5 mm] STEP 1 CUT C-914 LUMINUM GUIDE CHNNEL TO CORRECT LENGTH IF REQUIRED (TYPICLLY, LENGTH EQULS DOOR WIDTH. EXMPLE: DOOR WIDTH IS 36" THEREFORE CHNNEL IS 36".) STEP 2 PREPRE SLOT T LEST WIDE IN CENTER OF DOOR, ND T LEST 29/32" [23 mm] DEEP. IT IS RECOMMENDED TO MKE THE SLOT S CCURTE S POSSIBLE FOR SECURE FIT ND NET PPERNCE. STEP 3 DRILL S IN C-914 CHNNEL, ND PRE-DRILL S IN DOOR. SCREW CHNNEL INTO PLCE WHILE KEEG IT FLUSH WITH THE EDGE OF THE DOOR. (#8 SCREW SIZE RECOMMENDED) STEP 4 LOCTE C-913 (OR C-913-2) ROLLER GUIDE S REQUIRED ND SECURE TO FLOOR WITH #10 X 1-1/2" FLTHED SCREWS (4). STEP 5 CONTINUE WITH PROJECT BY INSTLLING HNGERS ND PLCING DOOR IN POSITION. OPTION 2: GUIDE CHNNEL IN FLOOR WITH GUIDE ON DOOR M 1-1/4" [31.8 mm] 29/32" [23 mm] 3/8" MIN [9.5 mm] STEP 1 CUT C-914 LUMINUM GUIDE CHNNEL TO CORRECT LENGTH IF REQUIRED. STEP 2 PREPRE SLOT IN FLOOR SME SIZE S INDICTED BOVE IN STEP 2. GUIDE CHNNEL SHOULD BE FLUSH WITH FINISHED FLOOR. STEP 3 DRILL S IN C-914 CHNNEL, ND PRE-DRILL S IN FLOOR. SCREW CHNNEL INTO PLCE. (#8 SCREW SIZE RECOMMENDED) STEP 4 LOCTE C-913 (OR C-913-2) ROLLER GUIDE FROM ECH EDGE OF DOOR. SECURE TO DOOR WITH #10 X 1-1/2" FLTHED SCREWS (4). STEP 5 CONTINUE WITH PROJECT BY INSTLLING HNGERS ND PLCING DOOR IN POSITION. CROWDERFRME PPLICTION: WHEN USING C-913/914 GUIDE SYSTEM WITH THE CROWDERFRME POCKET DOOR KIT PLESE REFER TO INSTRUCTIONS TO THE RIGHT 1/2" MIN to 3/4" MX [12.7 to 19.1 mm] K.N. CROWDER MFG. INC BURLOK DRIVE BURLINGTON, ONTRIO, CND, L7L 6B3 TELEPHONE: TOLL FREE PHONE: KNC (1562) FX: TOLL FREE FX: DOOR CROWDERFRME FOOT BRCKET WEBSITE: E-MIL: customerservice@kncrowder.com K.N. CROWDER INC. 210 EIGHTH STREET SOUTH LEWISTON, NEW YORK, U.S TELEPHONE: TOLL FREE FX: CRITICL DIMENSION: 1/2" C-914 NOTES: DUE TO THE LOCTION OF THE S FOR THE C-913 ROLLER GUIDE ON THE POCKET DOOR FOOT BRCKETS, THE C-914 CHNNEL MUST EXTEND BEYOND THE BCK EDGE OF THE DOOR (INSIDE POCKET). THIS DISTNCE CN BE NO GRETER OR LESS THN 1/2" IN ORDER FOR THE CHNNEL TO CTCH THE ROLLER WHEN FULLY CLOSED. IN THIS CSE YOU CN STOP THE SLOT FOR THE C-914 CHNNEL 1/2" MIN TO 3/4" MX FROM THE FRONT EDGE OF THE DOOR THUS HIDING THE CHNNEL. IT MY BE NECESSRY TO CUT THE CHNNEL TO SUIT THIS PPLICTION. SEE ILLUSTRTION FOR MORE DETILS.
OPTIMA QUADRANT / OFFSET QUADRANT
OPTIMA QUADRANT / OFFSET QUADRANT 71799 00 / Issue 1 / 15 Y Z DIMENSIONS Check the enclosure size in the tle elow mtches the showertry instlltion. = Widths: 800 Door = 780-805mm 900 Door = 880-905mm Y
More informationSURFACE OF MATTRESS MUST BE AT LEAST 5 IN. (127 MM) BELOW THE UPPER EDGE OF GUARDRAILS
Form# sw1800-1 tm MODERN CHILDREN S FURNITURE UFFIZI BUNK BED Model no. sw-1800 Thank you for your recent purchase of rgington s Uffizi bunk bed. Please read carefully below. You will find extremely important
More informationIPA FITTINGS FOR 16 X 5 MM GROOVE A/S J. PETERSENS BESLAGFABRIK JACOB PETERSENSVEJ 9, DK-9240 NIBE TEL: (+45) 98 35 15 00
IP FITTINGS FOR 16 X MM GROOVE 2012 /S J. PETERSENS ESLGFRIK JCO PETERSENSVEJ 9, DK-9240 NIE TEL: (+4) 98 3 1 00 3 FITTINGS FOR 16 X GROOVE Table of Contents PGE Wood profile 4 Suggestion - Number of
More informationFUEL SYSTEMS MERCARB 2 BARREL CARBURETOR 5 B
FUEL SYSTEMS 72681 MERCARB 2 BARREL CARBURETOR 5 B Tle of Contents Pge MerCr 2 BBL Cruretor.............. 5B-1 Torque Specifictions................ 5B-1 Tools............................... 5B-1 Specifictions.......................
More information2 DIODE CLIPPING and CLAMPING CIRCUITS
2 DIODE CLIPPING nd CLAMPING CIRCUITS 2.1 Ojectives Understnding the operting principle of diode clipping circuit Understnding the operting principle of clmping circuit Understnding the wveform chnge of
More informationWelch Allyn CardioPerfect Workstation Installation Guide
Welch Allyn CrdioPerfect Worksttion Instlltion Guide INSTALLING CARDIOPERFECT WORKSTATION SOFTWARE & ACCESSORIES ON A SINGLE PC For softwre version 1.6.5 or lter For network instlltion, plese refer to
More informationStart Here. IMPORTANT: To ensure that the software is installed correctly, do not connect the USB cable until step 17. Remove tape and cardboard
Strt Here 1 IMPORTANT: To ensure tht the softwre is instlled correctly, do not connect the USB cle until step 17. Follow the steps in order. If you hve prolems during setup, see Trouleshooting in the lst
More informationTraining Zone: Instruction Manual
Training Zone: Instruction Manual More questions? Our Customer Service team is available to answer your questions Monday - Friday from 9:00 M to 5:00 PM PT. E-mail customerservice@trxtraining.com Call
More informationJaERM Software-as-a-Solution Package
JERM Softwre-s--Solution Pckge Enterprise Risk Mngement ( ERM ) Public listed compnies nd orgnistions providing finncil services re required by Monetry Authority of Singpore ( MAS ) nd/or Singpore Stock
More informationSmall Business Networking
Why network is n essentil productivity tool for ny smll business Effective technology is essentil for smll businesses looking to increse the productivity of their people nd business. Introducing technology
More informationSmall Business Networking
Why network is n essentil productivity tool for ny smll business Effective technology is essentil for smll businesses looking to increse the productivity of their people nd processes. Introducing technology
More informationSmall Business Networking
Why network is n essentil productivity tool for ny smll business Effective technology is essentil for smll businesses looking to increse the productivity of their people nd processes. Introducing technology
More informationbody.allow-sidebar OR.no-sidebar.home-page (if this is the home page).has-custom-banner OR.nocustom-banner .IR OR.no-IR
body.llow-sidebr OR.no-sidebr.home-pge (if this is the home pge).hs-custom-bnner OR.nocustom-bnner.IR OR.no-IR #IDENTIFIER_FOR_THIS_SITE div#pge-continer.depends_on_page_ty PE llow-sidebr mens tht there
More informationSmall Business Networking
Why network is n essentil productivity tool for ny smll business Effective technology is essentil for smll businesses looking to increse the productivity of their people nd business. Introducing technology
More informationBUILT-IN MICROWAVE OVEN INSTALLATION INSTRUCTIONS
UILT-IN MIROWVE OVEN INSTLLTION INSTRUTIONS 24" (61.0 cm), 27" (68.6 cm), 30" (76.2 cm) This product is suitable for use above electric or gas built-in ovens, and below non-vented electric or gas cooktops.
More informationArticulating TV Wall Mount for 19" to 70" Flat Panel TVs
THIS INSTRUCTION BOOKLET CONTINS IMPORTNT SETY INORMTION. PLESE RED ND KEEP OR UTURE REERENCE. Lot Number: Date: rticulating TV Wall Mount for 19" to 7" lat Panel TVs Model No: DCD1319 Option 1 Option
More informationHow To Network A Smll Business
Why network is n essentil productivity tool for ny smll business Effective technology is essentil for smll businesses looking to increse the productivity of their people nd processes. Introducing technology
More informationClearPeaks Customer Care Guide. Business as Usual (BaU) Services Peace of mind for your BI Investment
ClerPeks Customer Cre Guide Business s Usul (BU) Services Pece of mind for your BI Investment ClerPeks Customer Cre Business s Usul Services Tble of Contents 1. Overview...3 Benefits of Choosing ClerPeks
More informationICOM JTG-II PROPANE OPTIMIZATION PROGRAM (POP) INSTALLATION MANUAL FLEET VEHICLES P13X4-9224-AA. Revision: A - Dated 2/13/13 Replaces: None
ICOM JTG-II PROPNE OPTIMIZTION PROGRM (POP) INSTLLTION MNUL P13X4-9224- Revision: - Dated 2/13/13 Replaces: None PROPNE OPTIMIZTION PROGRM OVERVIEW SYSTEM DESCRIPTION THE ICOM PROPNE OPTIMIZTION PROGRM
More informationExperiment 6: Friction
Experiment 6: Friction In previous lbs we studied Newton s lws in n idel setting, tht is, one where friction nd ir resistnce were ignored. However, from our everydy experience with motion, we know tht
More informationVendor Rating for Service Desk Selection
Vendor Presented By DATE Using the scores of 0, 1, 2, or 3, plese rte the vendor's presenttion on how well they demonstrted the functionl requirements in the res below. Also consider how efficient nd functionl
More informationPROF. BOYAN KOSTADINOV NEW YORK CITY COLLEGE OF TECHNOLOGY, CUNY
MAT 0630 INTERNET RESOURCES, REVIEW OF CONCEPTS AND COMMON MISTAKES PROF. BOYAN KOSTADINOV NEW YORK CITY COLLEGE OF TECHNOLOGY, CUNY Contents 1. ACT Compss Prctice Tests 1 2. Common Mistkes 2 3. Distributive
More informationMAINTENANCE ! WARNING SELECTING REPLACEMENT PARTS FOR YOUR OUTBOARD
Outbord Cre MAINTENANCE To keep your outbord in the best operting condition, it is importnt tht your outbord receive the periodic inspections nd mintennce listed in the Inspection nd Mintennce Schedule.
More informationSolidWorks Student License Academic Use Only
cademic Use Only TOLERNCE UNLESS NOTED DIMENSION PLCES IN DIMENSION TYPE LOCTIONL 0.050 0.020 0.005 NGULR 5 2 0.5 2. QUNTITY 1 Mobile Platform ssembly S. MSCIELLO M. BRDDOCK DRWN SCLE: 1:3 EML2322L--MP
More informationTablet Charging Wall Mount 12
User's Guide Tlet Chrging Wll Mount 12 For the ltest User Instlltion Guide plese visit: www.ergotron.com User's Guide - English Guí del usurio - Espñol Mnuel de l utilisteur - Frnçis Geruikersgids - Deutsch
More informationUse Geometry Expressions to create a more complex locus of points. Find evidence for equivalence using Geometry Expressions.
Lerning Objectives Loci nd Conics Lesson 3: The Ellipse Level: Preclculus Time required: 120 minutes In this lesson, students will generlize their knowledge of the circle to the ellipse. The prmetric nd
More informationGraphs on Logarithmic and Semilogarithmic Paper
0CH_PHClter_TMSETE_ 3//00 :3 PM Pge Grphs on Logrithmic nd Semilogrithmic Pper OBJECTIVES When ou hve completed this chpter, ou should be ble to: Mke grphs on logrithmic nd semilogrithmic pper. Grph empiricl
More informationUNLOCKING TECHNOLOGY IVECO
UNLOCKING TECHNOLOGY IVECO IVECO - CONTENTS PPLICTIONS PGE DS136 IVECO 3 DS177 IVECO CN 3 DIGNOSTIC SOCKETS LOCTIONS IVECO 4 GENERL OPERTION 5 6 TIPS & HINTS 15 2 Version: 2.3 July 2011 Copyright 2009
More informationHow To Set Up A Network For Your Business
Why Network is n Essentil Productivity Tool for Any Smll Business TechAdvisory.org SME Reports sponsored by Effective technology is essentil for smll businesses looking to increse their productivity. Computer
More informationtrademark and symbol guidelines FOR CORPORATE STATIONARY APPLICATIONS reviewed 01.02.2007
trdemrk nd symbol guidelines trdemrk guidelines The trdemrk Cn be plced in either of the two usul configurtions but horizontl usge is preferble. Wherever possible the trdemrk should be plced on blck bckground.
More informationHealth insurance exchanges What to expect in 2014
Helth insurnce exchnges Wht to expect in 2014 33096CAEENABC 02/13 The bsics of exchnges As prt of the Affordble Cre Act (ACA or helth cre reform lw), strting in 2014 ALL Americns must hve minimum mount
More informationSAMPLE SAMPLE SITE PLAN SITE PLAN SCALE: 1 : 150
SCOPE OF WORK: BSEMENT: - NEW FOUNDTION FOR PROPOSED RER DDITION - NO PROPOSED WORK FOR EXISTING INTERIOR BSEMENT 1ST FLOOR: - REMOVE EXISTING LOD BERING WLL (MOVE KITCHEN TO FRONT OF HOUSE) - DEMOLISH
More informationQuick Reference Guide: One-time Account Update
Quick Reference Guide: One-time Account Updte How to complete The Quick Reference Guide shows wht existing SingPss users need to do when logging in to the enhnced SingPss service for the first time. 1)
More informationPrescriptive Program Rebate Application
Prescriptive Progrm Rebte Appliction Check the pproprite progrm box for your rebte. OID Internl Use Only Cooling FSO (Fluid System Optimiztion) Foodservice Equipment Heting Lighting Motors & Drives Customer
More informationDesign Example 1 Special Moment Frame
Design Exmple 1 pecil Moment Frme OVERVIEW tructurl steel specil moment frmes (MF) re typiclly comprised of wide-flnge bems, columns, nd bem-column connections. Connections re proportioned nd detiled to
More informationBinary Representation of Numbers Autar Kaw
Binry Representtion of Numbers Autr Kw After reding this chpter, you should be ble to: 1. convert bse- rel number to its binry representtion,. convert binry number to n equivlent bse- number. In everydy
More informationHow To Know What A Pressure Ulcer Is
Pressure Ulcers ecourse: Module 2 Quiz I 1. Blck, brown or tn tissue tht dheres firmly to the wound bed or ulcer edges nd my be either firmer or softer thn surrounding tissue is:. Eschr b. Slough c. Grnultion
More informationINSTALLATION INSTRUCTIONS for Bifold Doors (JII103)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for premium composite, hollow and solid core molded Bifold Doors. Bifolds are designed for fast
More informationHelicopter Theme and Variations
Helicopter Theme nd Vritions Or, Some Experimentl Designs Employing Pper Helicopters Some possible explntory vribles re: Who drops the helicopter The length of the rotor bldes The height from which the
More informationHow To Rekey A Schlage Car With A Keyring Kit
Rekeying Manual For use with Keying Kits 40-132, 40-134 & 38-030 Rekeying is easy with Schlage Schlage engineers its locks for professional-grade durability, remarkable beauty and easy rekeying steps.
More informationHealth insurance marketplace What to expect in 2014
Helth insurnce mrketplce Wht to expect in 2014 33096VAEENBVA 06/13 The bsics of the mrketplce As prt of the Affordble Cre Act (ACA or helth cre reform lw), strting in 2014 ALL Americns must hve minimum
More informationMath 135 Circles and Completing the Square Examples
Mth 135 Circles nd Completing the Squre Exmples A perfect squre is number such tht = b 2 for some rel number b. Some exmples of perfect squres re 4 = 2 2, 16 = 4 2, 169 = 13 2. We wish to hve method for
More informationCommercial Cooling Rebate Application
Commercil Cooling Rebte Appliction Generl Informtion April 1 st 2015 through Mrch 31 st 2016 AMU CUSTOMER INFORMATION (Plese print clerly) Business Nme: Phone #: Contct Nme: Miling Address: City: Stte:
More informationUnderstanding Life Cycle Costs How a Northern Pump Saves You Money
Understnding Life Cycle Costs How Nrn Pump Sves You Money Reference: Hydrulic Institute (www.s.g) Introduction Wht Life Cycle Cost (LCC) Clculting Totl LCC LCC Components Wht Life Cycle Cost Life Cycle
More informationEasyMP Network Projection Operation Guide
EsyMP Network Projection Opertion Guide Contents 2 About EsyMP Network Projection Functions of EsyMP Network Projection... 5 Vrious Screen Trnsfer Functions... 5 Instlling the Softwre... 6 Softwre Requirements...6
More informationInstallation and Assembly: Desktop Mount with Desk Clamp and Grommet for 19" - 30" LCD Screens
Installation and ssembly: Desktop Mount with Desk Clamp and Grommet for 19" - 30" LCD Screens Models: LCT100S GROMMET INSTLLTION DESK CLMP INSTLLTION Max Load Capacity: 20 lbs (9 kg) 2300 White Oak Circle
More informationVersaRack Installation Instructions. masterack. Tools Required:
masterack Versaack Installation Instructions ll of us at asterack wish to thank you for your purchase of the Versaack. We are proud of this product and hope that you fi nd it a functional as well as a
More informationAll-Season Sunroom Sliding Glass Door Installation Instructions
ASRESGD-08 All-Season Sunroom Sliding Glass Door Installation Instructions Panel Frame Door Frame Left Side Foam Insulator IE241 H Bar Assembly Door Frame Top Track Panel Frame Door Frame Right Side Stationary
More information9.3. The Scalar Product. Introduction. Prerequisites. Learning Outcomes
The Sclr Product 9.3 Introduction There re two kinds of multipliction involving vectors. The first is known s the sclr product or dot product. This is so-clled becuse when the sclr product of two vectors
More informationRIGHT ANGLE CLINCH FASTENERS BULLETIN
BULLETIN R 215 R e v 515 PEM R NGLE fasteners provide strong right angle attachment points in sheet metal or PC boards. Types R and RS for metal are simply pressed into a rectangular mounting hole of the
More informationINSTRUCTIONS THOROUGHLY BEFORE BEGINNING***************
Bill of Materials: RAC0012 Green Wing Aerodynamic Skirt Kit Item Part Number Description Quantity 1 RMC0218 Gen 2 Trailer Skirt Roadside 1 2 RMC0219 Gen 2 Trailer Skirt Curbside 1 3 RMC0041 Trailer Skirt
More informationPhysics 43 Homework Set 9 Chapter 40 Key
Physics 43 Homework Set 9 Chpter 4 Key. The wve function for n electron tht is confined to x nm is. Find the normliztion constnt. b. Wht is the probbility of finding the electron in. nm-wide region t x
More information1.00/1.001 Introduction to Computers and Engineering Problem Solving Fall 2011 - Final Exam
1./1.1 Introduction to Computers nd Engineering Problem Solving Fll 211 - Finl Exm Nme: MIT Emil: TA: Section: You hve 3 hours to complete this exm. In ll questions, you should ssume tht ll necessry pckges
More informationA vital connection. Getting the job done: What to expect. How we work
NEW GAS CONNECTION MULTIPLE PROPERTIES, INDUSTRIAL AND COMMERCIAL A vitl connection Northern Gs Networks owns ll of the gs pipelines in the North Est, most of Yorkshire nd northern Cumbri, servicing 2.7
More informationMUSTANG II IFS COMPLETE PARTS PACKAGE
MUSTANG II IFS COMPLETE PARTS PACKAGE Your Southern Rods & Parts Mustang II IFS Parts Package contains the following items: 1 pr) Upper Control Arms (2023) 1) Upper Arm Bolt Kit (MP-001-A) 1 pr) Lower
More information3 The Utility Maximization Problem
3 The Utility Mxiiztion Proble We hve now discussed how to describe preferences in ters of utility functions nd how to forulte siple budget sets. The rtionl choice ssuption, tht consuers pick the best
More informationVoIP for the Small Business
Reducing your telecommunictions costs VoIP (Voice over Internet Protocol) offers low cost lterntive to expensive trditionl phone services nd is rpidly becoming the communictions system of choice for smll
More informationAntiSpyware Enterprise Module 8.5
AntiSpywre Enterprise Module 8.5 Product Guide Aout the AntiSpywre Enterprise Module The McAfee AntiSpywre Enterprise Module 8.5 is n dd-on to the VirusScn Enterprise 8.5i product tht extends its ility
More informationRecognition Scheme Forensic Science Content Within Educational Programmes
Recognition Scheme Forensic Science Content Within Eductionl Progrmmes one Introduction The Chrtered Society of Forensic Sciences (CSoFS) hs been ccrediting the forensic content of full degree courses
More informationINSTALLATION INSTRUCTIONS. 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD IMPORTANT NOTES
INSTALLATION INSTRUCTIONS 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY
More informationFIXED PLATE INSTALLATION FOR STRAIGHT TRUCKS
FIXED PLTE INSTLLTION FOR STRIGHT TRUCKS For staight trucks only, not for trailers. For single stage and two stage mast forklifts. Dump Bodies require special construction, contact for specific instructions.
More informationCHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS
CHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings,
More informationSliding Barn Door Hardware Installation Instructions BALDUR and ODEN
Sliding Barn Door Hardware Installation Instructions BALDUR and ODEN Installation Instructions Structural Information For standard systems and most custom single door opening systems. General Overview
More informationExample A rectangular box without lid is to be made from a square cardboard of sides 18 cm by cutting equal squares from each corner and then folding
1 Exmple A rectngulr box without lid is to be mde from squre crdbord of sides 18 cm by cutting equl squres from ech corner nd then folding up the sides. 1 Exmple A rectngulr box without lid is to be mde
More informationUPLIFT Height Adjustable Standing Desk (T-Frame) DIRECTIONS FOR ASSEMBLY AND USE - - ALSO - - Watch our assembly video
UPLIFT Height Adjustable Standing Desk (T-Frame) DIRECTIONS FOR ASSEMBLY AND USE - - ALSO - - Watch our assembly video http://bit.ly/9ywwh! CAUTION MAKE SURE NO OBSTACLES ARE IN THE DESK S PATH AND ALL
More informationTHE INTELLIGENT VEHICLE RECOVERY AND FLEET MANAGEMENT SOLUTION
KENYA THE INTELLIGENT VEHICLE RECOVERY AND FLEET MANAGEMENT SOLUTION INTRODUCTION Hving estblished itself in no less thn eleven Sub-Shrn countries nd with more thn 230 000 vehicles lredy on its system
More informationAUTHORISED SERVICE AGENTS: CARBA-TEC Pty. Ltd. 40 Harries Road Coorparoo, QLD 4151 Ph: (07) 3397 2577 Fax: (07) 3397 2785
UTHORISED SERVICE GENTS: CR-TEC Pty. Ltd. 40 Harries Road Coorparoo, QLD 4151 Ph: (07) 3397 2577 Fax: (07) 3397 2785 CR-TEC (NSW) Pty. Ltd. 32 Percy Street uburn, NSW 2144 Ph: (02) 9649 5077 Fax: (02)
More informationPROBLEMS 13 - APPLICATIONS OF DERIVATIVES Page 1
PROBLEMS - APPLICATIONS OF DERIVATIVES Pge ( ) Wter seeps out of conicl filter t the constnt rte of 5 cc / sec. When the height of wter level in the cone is 5 cm, find the rte t which the height decreses.
More informationGuidelines for Earthquake Bracing of Residential Water Heaters
Guidelines for Earthquake Bracing of Residential Water Heaters Department of General Services Division of the State Architect 1102 Q Street, Suite 5100 Sacramento, CA 95814 Phone: (916) 324-7099 Fax: (916)
More informationUnit 6: Exponents and Radicals
Eponents nd Rdicls -: The Rel Numer Sstem Unit : Eponents nd Rdicls Pure Mth 0 Notes Nturl Numers (N): - counting numers. {,,,,, } Whole Numers (W): - counting numers with 0. {0,,,,,, } Integers (I): -
More informationINSTALLATION INSTRUCTIONS 24" (61.0 CM) ELECTRIC SINGLE AND DOUBLE BUILT-IN OVEN
INSTLLTION INSTRUTIONS 24" (61.0 M) LTRI SINGL N OUL UILT-IN OVN Table of ontents UILT-IN OVN SFTY... 1 INSTLLTION RQUIRMNTS... 2 Tools and Parts... 2 Location Requirements... 2 lectrical Requirements...
More informationNew Internet Radio Feature
XXXXX XXXXX XXXXX /XW-SMA3/XW-SMA4 New Internet Rdio Feture EN This wireless speker hs een designed to llow you to enjoy Pndor*/Internet Rdio. In order to ply Pndor/Internet Rdio, however, it my e necessry
More informationTable of Contents. www.hunterfan.com. What to Expect with. Preparation. Tools Needed. Wiring. Hanging the Fan. Blades. Motor Housing.
www.hunterfan.com Table of Contents What to Expect with Your Installation 30 inches Hanging the Fan Wiring 8 Maintenance, Operation & Cleaning Light Kit 13??? 14 1 9 Troubleshooting 11 5 Blades Motor Housing
More informationT3666-60A POOL ASSEMBLY AND INSTALLATION MANUAL. Above Ground 52 Round Pools
T3666-60 SSEMBLY ND INSTLLTION MNUL bove Ground 52 Round Pools Note: Deck and fence accessories shown are optional. THIS MNUL EXPLINS THE CORRECT METHOD TO SSEMBLE YOUR NEW SWIMMING. RED THESE INSTRUCTIONS
More informationArea. GABLES 411: Gables Citywalk/Waterford Square a
Are GABLES 411: Gbles Citywlk/Wterford Squre Where is the closest post office? 3740 Greenbrir St. Houston, TX 0.5 Miles (713) 528-5875 Where is the closest grocery store? Whole Foods, 2955 Kirby Dr. Houston,
More informationApplication Bundles & Data Plans
Appliction Appliction Bundles & Dt Plns We ve got plns for you. Trnsporttion compnies tody ren t one-size-fits-ll. Your fleet s budget, size nd opertions re unique. To meet the needs of your fleet nd help
More informationMathematics. Vectors. hsn.uk.net. Higher. Contents. Vectors 128 HSN23100
hsn.uk.net Higher Mthemtics UNIT 3 OUTCOME 1 Vectors Contents Vectors 18 1 Vectors nd Sclrs 18 Components 18 3 Mgnitude 130 4 Equl Vectors 131 5 Addition nd Subtrction of Vectors 13 6 Multipliction by
More informationSliding Door Hardware Installation Instructions
Sliding Door Hardware Installation Instructions Installation Instructions Structural Information For standard systems and most custom single door opening systems. General Overview ff All Krown Lab sliding
More informationv T R x m Version PREVIEW Practice 7 carroll (11108) 1
Version PEVIEW Prctice 7 crroll (08) his print-out should he 5 questions. Multiple-choice questions y continue on the next colun or pge find ll choices before nswering. Atwood Mchine 05 00 0.0 points A
More informationEngineer-to-Engineer Note
Engineer-to-Engineer Note EE-280 Technicl notes on using Anlog Devices DSPs, processors nd development tools Visit our Web resources http://www.nlog.com/ee-notes nd http://www.nlog.com/processors or e-mil
More informationIntroducing Kashef for Application Monitoring
WextWise 2010 Introducing Kshef for Appliction The Cse for Rel-time monitoring of dtcenter helth is criticl IT process serving vriety of needs. Avilbility requirements of 6 nd 7 nines of tody SOA oriented
More informationBasic Ultrasound Views
Bsic Ultrsound Views 2 Kenneth D. Horton K.D. Horton Echo/Vsculr Lortory, Intermountin Medicl Center, Murry, UT, USA e-mil: kd.horton@comcst.net T.P. Arhm (ed.), Cse Bsed Echocrdiogrphy, DOI: 10.1007/978-1-84996-151-6_2,
More informationRPI ROOF PRODUCTS, INC. Email: rpicurbs@comcast.net Visit us on the web at www.rpicurbs.com
MIN OFFICE 7616 Lee Highway Chattanooga, TN 37421 Phone: 423-892-8620 Fax: 423-892-2107 Toll Free: 800-262-6669 RPI PRODUCTS, INC. Email: rpicurbs@comcast.net Visit us on the web at www.rpicurbs.com WEST
More informationPHY 140A: Solid State Physics. Solution to Homework #2
PHY 140A: Solid Stte Physics Solution to Homework # TA: Xun Ji 1 October 14, 006 1 Emil: jixun@physics.ucl.edu Problem #1 Prove tht the reciprocl lttice for the reciprocl lttice is the originl lttice.
More informationPolynomial Functions. Polynomial functions in one variable can be written in expanded form as ( )
Polynomil Functions Polynomil functions in one vrible cn be written in expnded form s n n 1 n 2 2 f x = x + x + x + + x + x+ n n 1 n 2 2 1 0 Exmples of polynomils in expnded form re nd 3 8 7 4 = 5 4 +
More informationBATHROOM FAUCET ITEM #0040242 0039992 MODEL #67510-6001 67510-6027H2. Francias / Español p. 9 ATTACH YOUR RECEIPT HERE
quasource is a registered trademark of LF, LLC. ll Rights Reserved. ITEM #0040242 0039992 BTHROOM FUCET MODEL #67510-6001 67510-6027H2 Francias / Español p. 9 TTCH YOUR RECEIPT HERE Serial Number Purchase
More informationLINEAR TRANSFORMATIONS AND THEIR REPRESENTING MATRICES
LINEAR TRANSFORMATIONS AND THEIR REPRESENTING MATRICES DAVID WEBB CONTENTS Liner trnsformtions 2 The representing mtrix of liner trnsformtion 3 3 An ppliction: reflections in the plne 6 4 The lgebr of
More informationExample 27.1 Draw a Venn diagram to show the relationship between counting numbers, whole numbers, integers, and rational numbers.
2 Rtionl Numbers Integers such s 5 were importnt when solving the eqution x+5 = 0. In similr wy, frctions re importnt for solving equtions like 2x = 1. Wht bout equtions like 2x + 1 = 0? Equtions of this
More informationNATURAL RAILING INSTALLATION INSTRUCTIONS
NTURL RILING INSTLLTION INSTRUCTIONS Manufactured by fiberondecking.com 800.573.8841 FI-0217-PKG 5/14 Natural Railing Installation Instructions Natural Top Rail Profile Required Tools and Supplies: Power
More informationSIMPLEX UNICAN LOCKS CHANGING THE CODE / COMBINATION 900 Series 1000 Series L1000 Series LP1000 Series EE1000 Series 2000 Series 2015 Series
SIMPLEX UNICAN LOCKS CHANGING THE CODE / COMBINATION 900 Series 1000 Series L1000 Series LP1000 Series EE1000 Series 2000 Series 2015 Series 2400/2500 Series 3000 Series 3100 Series Simplex 5000 Series
More informationSECTION VOYAGE POSTURAL COMPONENTS INSTALLATION AND ADJUSTMENT GUIDE ENGLISH
SETION ENGLISH VOYGE POSTURL OMPONENTS INSTLLTION N JUSTMENT GUIE Please read these instructions carefully before beginning the installation. Failure to understand and follow installation instructions
More informationUplift Capacity of K-Series Open Web Steel Joist Seats. Florida, Gainesville, FL 32611; email: psgreen@ce.ufl.edu
Uplift Cpcity of K-Series Open Web Steel Joist Sets Perry S. Green, Ph.D, M.ASCE 1 nd Thoms Sputo, Ph.D., P.E., M.ASCE 2 1 Assistnt Professor, Deprtment of Civil nd Costl Engineering, University of Florid,
More informationReasoning to Solve Equations and Inequalities
Lesson4 Resoning to Solve Equtions nd Inequlities In erlier work in this unit, you modeled situtions with severl vriles nd equtions. For exmple, suppose you were given usiness plns for concert showing
More informationEcon 4721 Money and Banking Problem Set 2 Answer Key
Econ 472 Money nd Bnking Problem Set 2 Answer Key Problem (35 points) Consider n overlpping genertions model in which consumers live for two periods. The number of people born in ech genertion grows in
More informationModels A spe n, Econoline C o l o n i al. and Savoy. Installation Instructions. Contractors Wardrobe
Installation Instructions Models A spe n, Econoline C o l o n i al and Savoy Contractors Wardrobe DESIGNERS MANUFACTURERS TOLL FREE: (800) CW-DOORS (800) 293-77 www.cwdoor.com 2121 Avenue Hall Valencia,
More informationWILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS
WILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS Instruction Booklet 18 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN POWERFUL LIFTING COMPONENTS. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE
More informationReview Problems for the Final of Math 121, Fall 2014
Review Problems for the Finl of Mth, Fll The following is collection of vrious types of smple problems covering sections.,.5, nd.7 6.6 of the text which constitute only prt of the common Mth Finl. Since
More informationFreightliner AirLiner Suspension 32.05
Freightliner irliner Suspension 3.05 Ride Height djustment NOTICE Failure to adjust the suspension ride height could adversely affect driveline angles. lso, if the air springs are set too high, the driver
More informationMorgan Stanley Ad Hoc Reporting Guide
spphire user guide Ferury 2015 Morgn Stnley Ad Hoc Reporting Guide An Overview For Spphire Users 1 Introduction The Ad Hoc Reporting tool is ville for your reporting needs outside of the Spphire stndrd
More informationPOD Visor Instructions
POD Visor Instructions Please read fully before beginning assembly and mounting the Visor Parts List - Visor Left Part (LV), Visor Right Part (RV) Qty 2, Aluminum Crossbars Hardware - Qty 17, 1/4" X 3/4"
More information