NPN-Si-Fototransistor mit V λ Charakteristik Silicon NPN Phototransistor with V λ Characteristics Lead (Pb) Free Product - RoHS Compliant SFH 3710

Transcription

1 NPN-Si-Fototransistor mit V λ Charakteristik Silicon NPN Phototransistor with V λ Characteristics Lead (Pb) Free Product - RoHS Compliant SFH 371 Wesentliche Merkmale Sehr kleines SMT Gehäuse Angepaßt an die Augenempfindlichkeit (V λ ) Anwendungen Umgebungslicht-Detektor Beleuchtungsmesser Dimmungssensor für Hintergrundbeleuchtung Messen/Steuern/Regeln Features Very small SMT package Adapted to human eye sensitivity (V λ ) Applications Ambient light detector Exposure meter for daylight and artificial light Sensor for Backlight-Dimming For control and drive circuits t Typ Type Bestellnummer Ordering Code SFH 371 Q6511A SFH 371-2/3 Q6511A SFH 371-3/4 Q6511A Fotostrom, E e = 1 µw/cm², λ = 56 nm, V CE = 5 V Ipce (µa) Einzelgruppen auf Anfrage / single bins on request

2 SFH 371 Grenzwerte (T A = 25 C) Maximum Ratings Bezeichnung Parameter Betriebs- und Lagertemperatur Operating and storage temperature range Kollektor-Emitterspannung Collector-emitter voltage Kollektorstrom Collector current Emitter-Kollektorspannung Emitter-collector voltage Wert Value T op ; T stg C V CE 5.5 V I C 2 ma V EC.5 V Einheit Unit Kennwerte (T A = 25 C) Characteristics Bezeichnung Parameter Wellenlänge der max. Fotoempfindlichkeit Wavelength of max. sensitivity Spektraler Bereich der Fotoempfindlichkeit S = 1% von S max Spectral range of sensitivity S = 1% of S max Bestrahlungsempfindliche Fläche Radiant sensitive area Abmessung der Chipfläche Dimensions of chip area Halbwinkel Half angle Kapazität, V CE = V, f = 1 MHz, E = Capacitance Dunkelstrom Dark current V R = 5 V Temperturkoeffizient Temperature Coefficient Normlicht A / Standard Light A λ = 55 nm Wert Value λ Smax 57 nm λ nm Einheit Unit A.29 mm 2 L B L W mm mm ϕ ± 6 Grad. deg. C CE 4 pf I CEO 3 (< 5) na TK.9 TK nm %/K %/K

3 SFH 371 Kennwerte (T A = 25 C) Characteristics Bezeichnung Parameter Fotostrom E e = 1 µw/cm², λ = 56 nm, V CE = 5 V E v = 1 lx, Normlicht/Standard light A Kollektor-Emitter-Sättigungsspannung Collector-emitter saturation voltage I C = I PCEmin 1).3, E e = 1 µw/cm², λ = 56 nm I PCE Wert Value Einheit Unit µa µa V CEsat mv 1) I PCEmin ist der minimale Fotostrom der jeweiligen Gruppe 1) I PCEmin is the min. photocurrent of the specified group

4 SFH 371 Relative Spectral Sensitivity S rel = f (λ) Srel / % lambda / nm Collector-Emitter Capacitance C CE = f (V CE ) C CE 4. pf I PCE = f (E V ), V CE = 5 V Ipce (ma) 1E+2 1E+1 1E+ 1E-1 1E-2 1E-3 1E-4 1.E+ 1.E+1 1.E+2 1.E+3 1.E+4 1.E+5 Ev (lx) I PCE = f (E V ), V CE = 5 V normalized to 1lx Ipce rel (%) E+ 1.E+1 1.E+2 1.E+3 1.E+4 1.E+5 Ev (lx) E-3 1E-2 1E-1 1E+ 1E+1 1E+2 V V CE Directional Characteristics S rel = f (ϕ) ϕ 1..8 OHF

5 SFH 371 Maßzeichnung Package Outlines Maße in mm (inch) / Dimensions in mm (inch) Empfohlenes Lötpaddesign Recommended Solderpad Design Maße in mm / Dimensions in mm Bauteil positioniert Component location on pad OHFP

6 SFH 371 Lötbedingungen Vorbehandlung nach JEDEC Level 2 Soldering Conditions Preconditioning acc. to JEDEC Level 2 Reflow Lötprofil für bleifreies Löten (nach J-STD-2C) Reflow Soldering Profile for lead free soldering (acc. to J-STD-2C) T 3 C C 24 C 217 C Maximum Solder Profile Recommended Solder Profile Minimum Solder Profile 1 s min 3 s max OHLA687 + C 26 C -5 C 245 C ±5 C +5 C 235 C - C s max 1 s max Ramp Down 6 K/s (max) 1 5 Ramp Up 3 K/s (max) 25 C s 3 t Published by OSRAM Opto Semiconductors GmbH Wernerwerkstrasse 2, D-9349 Regensburg All Rights Reserved. The information describes the type of component and shall not be considered as assured characteristics. Terms of delivery and rights to change design reserved. Due to technical requirements components may contain dangerous substances. For information on the types in question please contact our Sales Organization. Packing Please use the recycling operators known to you. We can also help you get in touch with your nearest sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred. Components used in life-support devices or systems must be expressly authorized for such purpose! Critical components 1, may only be used in life-support devices or systems 2 with the express written approval of OSRAM OS. 1 A critical component is a component usedin a life-support device or system whose failure can reasonably be expected to cause the failure of that life-support device or system, or to affect its safety or effectiveness of that device or system. 2 Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain human life. If they fail, it is reasonable to assume that the health of the user may be endangered