EC-Declaration of Conformity (According to the guidelines 1999/5/EG (R&TTE) Installation Guide Motorcycle Alarm System Type 338A/998A Producer / person responsible Ensures that the product: Type: Designated use: WilTec Wildanger Technik GmbH Koenigsbenden 12 52249 Eschweiler, Germany 75998, Inwells Motorcycle Alarm System 338A Securing two-wheeled vehicles when properly used, the above mentioned model fulfils the basic requirements and the guidelines complying with the 1999/5/EC R&TTE When evaluating the product according to the EU demands, the following standards were applied: R&TTE EN300 220-3 V1.3.1:2000 EN301 489-3 V1.4.1:2002 If the product is changed this declaration loses its validity. Eschweiler, 14. December 2006 Important notice: The reprint or reproduction, even of excerpts, and any commercial use, even in part of this instructions manual require the written permission of Wiltec Wildanger Technik GmbH. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignificantly. Bernd Wildanger Manager The product can be introduced in all EU-states without restrictions (as well as in other states that follow the EU-Directive 1999/5/EG). Updating the documentation If you have suggestions for improvement or have found any irregularities please contact us.
General Information Requirements: 1. Voltage: DC 12Volt +/- 3Volt 2. The motorcycle has to run idle in order to start the engine. 3. The control unit has to be positioned in a damp-proof place of the motorcycle because the device is not water-proof. 4. The control unit must not be thrown or exposed to moisture. Functional description: Audio-Optic Alarm: Press and the signal horn rings out once, the blinker flashes, after 3 sec the alarm is activated. Disarm: Press and the horn rings twice the blinker flashes twice indicating that the system is disarmed. Shaking- Alarm: if the alarm system is activated and the motorcycle starts shaking, the blinker flashes and the horn warns. If the shaking happens again in 5 sec, the immobilizer is activated and the engine cannot be started, the blinker flashes and the horn rings. Motorcycle searching: If the system is activated, press and an alarm is triggered, so that you can find out the location of your vehicle. Silent Alarm: By pressing the button you activate the silent alarm. In case the motorcycle is shaken a short acoustical signal is given followed by an optical warning issued by the blinker. Immobilizer: It is only for motorcycles equipped with a negative switching emergency switch. Because this function is optional, one can let it disconnected by motorcycles with positive switching emergency switch or by rollers. For the immobilizer the grey and the pink cables are assigned. Remote start: Press, the engine starts automatically. In case the engine does not run, just push again the button. The starting motor is activated as long you press the button of the remote control. (It does not function if the motorcycle battery is too weak or empty.) Switching off the engine: Just press for turning off and the engine shuts down. Anti Hijacking: In case your motorcycle is stolen while the machine is running, just press the engine stops immediately, the horn rings permanently and the blinker flashes. (This function is only ensured, if the motorcycle is started via remote control or if the immobilizer (grey / pink cables) is connected. Adjusting the sensitivity: In case the sensitivity is set too low, sever the green cable. (see the illustrations) Setting sensitivity via remote control: press and or and buttons (depending on the model year) of the remote control simultaneously, the blinker flashes quickly three times, indicating that sensitivity can be adjusted via remote control. Briefly press only once and the shock sensitivity changes. The degree of sensitivity is indicated via blinker. There are four sensitivity levels that can be set. After setting, press and you quit the set level. (1x blinking insensitive, 4x blinking very sensitive).
Connection Diagram Motorcycle Type 338A/998A Rot An Batterie Plus anschliessen Antenne Grau Not-Aus Schalter (zum Schalter) Pink (vom Schalter) Schwarz An Batterie Minus / Masse Orange Symbole und Funktione n Rot Weiss Gelb Symbole Funktion Blinker Alarmanlage schärfen Gelb Alarmanlage deaktivieren Mute Alarm (lautloser Alarm) Motorstart Signal / Horn Blau Kabel zum Anlasserrelais (Positiv)
Fault tracing Motorcycle Type 338A/998A Installations problems and their causes: Problem The alarm system shows no function The alarm system cannot be activated, or the alarm is triggered immediately when enabled By engine remote start the motorcycle won t start (starting motor rotates itself) Beim Motorfernstart startet das Motorrad nicht (Starter dreht nicht) The alarm is triggered but the siren does not go off When the remote control is activated, the blinkers do not flash Cause / Elimination The supply voltage is not connected / please check the contact of the red and of both black cables Are all the cables connected? Plus and minus alone are not enough to test the system! The alarm system detects a false signal / the orange cable is incorrectly connected and has still +12V when armed/activated The cables (orange) an ACC (ignition switch positive) is not properly connected / check the cabling. The starter relay is not positively switched but negatively / Connect another relay to the earth side of the starter relay which is activated by remote start via blue cable (of the alarm system). The connector to the alarm siren has no contact / plug in the connector The battery of the motorcycle could be discharged please change the battery to ensure the alarm function. If you have checked the whole cable layout and read these instructions and still cannot put the alarm system into operation, note down which cable you have connected and send us an Email, as well as a description of the malfunction. Send your Email-support to: support@wiltec.info, without a first contact via Email no (!) telephone support is provided! By telephone and written enquires please always specify your customer and order number. In case you did not purchase the alarm system from WilTec Wildanger Technik GmbH, please contact your seller.
Symbols and functions Symbols and functions Activate the alarm system Deactivate the alarm system Mute alarm Motor starter Red connect it to the plus of the battery Grey Emergency off switch/ Emergency Power Off to the switch Pink Emergency off switch/ Emergency Power Off from the switch Black to the minus of the battery / earth Orange ignition switch positive ACC Yellow Yellow blinker Blue cable to the starter relay (positive) White Red Signal /horn