Button 1 Button 2. Button 3 Button 4. Programmed Remote Transmitter. Button Function Condition

Transcription

1 ST9000 SECURITY SYSTEM Button Function Condition 1 a. Arm and lock doors b. Car finder with sound c. Temporary stop alarm from sounding d. Remote lock doors 1 for 2 sec. Panic Anytime a. Alarm is disarmed b. Alarm is armed c. Alarm is sounding d. Doors are unlocked Button 1 Button 2 Button 3 Button 4 2 a. Disarm b. Remote unlock doors c. Stop alarm from sounding 2 for 2 sec. Second unlock 3 a. Super soft chirp arm b. Car finder with soft chirp c. Anti-carjacking a. Alarm is armed b. Doors locked c. Alarm is armed Alarm is disarmed a. Alarm is disarmed b. Alarm is armed c. Engine running Programmed Remote Transmitter 3 for 2 sec. Close windows Alarm is disarmed 4 Open trunk or engine start Key in OFF position 2+3 Output channel 3 Anytime 2+4 Output channel 4 Anytime CODE LEARNING FOR REPLACEMENT TRANSMITTERS ONLY a. Turn key to ON position. Press valet button 10 times within 8 seconds. Siren will chirp 3 times to indicate code learning mode. b. Press button 1 of the first transmitter once. Then, press Button 1 of the second transmitter once. The siren will output a confirmation chirp(s) with each remote transmitter that is learned. For example, after the first remote transmitter is programmed, the siren will chirp once. After the second transmitter is programmed, the siren will chirp twice. Up to 4 transmitters can be programmed. c. If only one remote transmitter needs to be programmed/added, the other remote transmitter(s) must be reprogrammed at this time. d. Turn key to OFF position or wait for 8 seconds and the system will exit code learning. e. Up to 4 transmitters can be programmed per module. ARMING a. Press button 1. b. Siren will chirp once or no chirp (See Function Selection 6). c. Parking lights will flash once. d. Doors will be locked with a 0.5 second or 3.5 second pulse (See Function Selection 1). e. LED will flash slowly. NOTE: If any doors are open the siren will output 2 warning chirps. f. Starter/ignition kill circuit is enabled. (NC Relay) g. The system is armed and all sensors are in ready status. If the alarm is triggered within 3 seconds, the siren will chirp twice and the open circuit is by-passed until the triggering source is stable. WINDOW CLOSE ( ) OUTPUT Press and hold button 3 for 2 seconds (If your car has been installed with the window closing module). This output will remain continuous for 30 seconds. SUPER SOFT CHIRP FOR ARMING a. Press button 3. b. Siren will chirp softly once or no chirp (See Function Selection 6). c. Parking lights will flash once. d. Doors will be locked with a 0.5 second or 3.5 second pulse (See Function Selection 1). e. LED will flash slowly. NOTE: If any doors are open, the siren will output 5 warning chirps and the LED will flash quickly. f. Starter/ignition kill circuit is enabled. (NC Relay) g. The system is armed and all sensors are in ready status. If the alarm is triggered within 3 seconds, the siren will chirp twice and the open circuit is by-passed until the triggering source is stable. DISARMING a. Press button 2. b. Siren will chirp 3 times or no chirp (See Function Selection 6). If siren chirps and parking lights flash 4 times after pressing button 2, the alarm has been triggered during armed mode and the LED will flash to indicate the triggered zone as follows: 1. Ignition: 6 flashes, pause, then 6 flashes. 2. Doors: 5 flashes, pause, then 5 flashes. 3. Trunk: 4 flashes, pause, then 4 flashes. 4. Auxiliary: 3 flashes, pause, then 3 flashes. 5. Heavy impact: 2 flashes, pause, then 2 flashes. 6. Light impact: 1 flash, pause, then 1 flash. NOTE:To reset the LED: Turn key to ON position or re-arm system. c. Parking lights will flash 3 times. d. Dome light will stay on for 30 seconds or until ignition is turned on. e. Doors will be unlocked with a 0.5 second or 3.5 second pulse (See Function Selection 1). f. LED will be off. g. Starter/ignition kill circuit is disabled (NC Relay). EMERGENCY DISARMING OVERRIDE (FACTORY PRESET VALUE: PRESS BUTTON 5 TIMES) a. Turn key to ON position. b. Press valet button 5 times (default value). Siren will chirp 4 times which indicates the system is disarmed. This process must be finished within 8 seconds. damage or personal injuries resulting from the use of the information. Installation by qualified automotive professionals is highly recommended. REV ST /6 1

2 CHANGE EMERGENCY DISARMING OVERRIDE VALUE a. Turn key to ON position. Press valet button 5 times within 8 seconds. Siren will chirp 4 times to indicate that the system is ready to change the Emergency Disarming Override value. b. Press the valet button (1-15max) as the value you prefer within 8 seconds (if the number is over 15, the system will return back to the original value). The siren will output confirmation chirps for the total value that was selected. AUTOMATIC DOOR (SEE FUNCTION SELECTION 4) When the key turns from the OFF position, to the ON position, the doors will lock after 20 seconds. AUTOMATIC DOOR UN When the key turns from the ON position, to the OFF position, the doors will automatically unlock. VALET MODE (SEE FUNCTION SELECTION 12) Valet mode ON: a. Turn key to ON position, within 8 seconds, press and hold valet button for 3 seconds. b. LED will remain ON constantly to indicate the system has entered Valet mode. Wait 8 seconds or turn key to OFF position. Valet mode OFF: a. Turn key to ON position, press and hold valet button for 3 seconds. b. LED will turn OFF to indicate the system has exited valet mode. Wait 8 seconds or turn key to OFF position. c. While in valet mode, all functions inoperable except door locks. d. If the system is armed the siren will chirp twice to indicate that valet mode is ON. PANIC a. Press button 1 for 3 seconds. The siren will sound. The parking lights and dome light will flash together for 30 seconds. b. Press button 1 or button 2 to turn off Panic mode. CAR FINDER While the system is armed, do the following: a. Press button 1: Siren will chirp once, parking lights and dome light will flash together for 10 seconds. b. Or, Press button 3: Siren will soft chirp once, parking lights and dome light will flash together for 10 seconds. c. Press button 2 to stop Car Finder mode and disarm the system. ANTI-CARJACKING (SEE FUNCTION SELECTION 7) a. While the engine is running and the doors are closed, press button 3. Within 8 seconds, open the drivers door to activate the anticarjacking mode. If the door is not opened within 8 seconds, the Anticarjacking mode will not be entered. b. Close the drivers door to start the 30 second countdown. The LED will begin to flash quickly. c. After the 30 second countdown, the siren will chirp every 2 seconds. After 20 more seconds, the siren will sound continuously and the parking lights will flash. If the ignition is turned off, the siren and parking lights will stop. d. Once the ignition has been turned to the OFF position, the starter/ignition kill circuit is enabled. (if the circuit (NC) relay is connected). e. Disarming anti-carjacking: Press button 3 for two seconds. The parking lights will flash once for confirmation. 2-STAGE SHOCK SENSOR a. Immediately after a light impact, the siren will output 5 warning chirps and the parking lights will flash once. b. Immediately after a heavy impact, the siren will sound for 30 seconds and the parking lights will flash. OPEN TRUNK OR ENGINE START OUTPUT a. Press button 4 to open trunk or remote start engine. b. If the system was previously in the armed mode, both the trunk trigger input and the shock sensor are by-passed. After 30 seconds, the system will be in armed mode again. CHANNEL 3 AND CHANNEL 4 OUTPUT Press buttons 2+3 together to output channel 3 ( 300mA). This output will remain constant until buttons 2+3 are released. Press buttons 2+4 together to output channel 4 ( 300mA). This output will remain constant until buttons 2+4 are released. DOOR CONTROL a. The doors can be locked with the transmitters, while driving. b. Simply press the lock button. c. The doors can be unlocked with the transmitters, while driving. d. Simply press the unlock button. AUTOMATIC REARMING (SEE FUNCTION SELECTION 10) a. After disarming, when the ignition is in the OFF position and all doors are closed, the system will re-arm automatically within 30 seconds. LAST DOOR ARMING (SEE FUNCTION SELECTION 8) a. When the last door is closed and the ignition is in the OFF position, after 30 seconds the system will arm automatically. b. If one of the doors is opened during the above 30 second countdown, the system will postpone the arming until the last door is closed. ADDITIONAL TRIGGER SENSOR Additional sensors can be added that send a negative output trigger. STARTER/IGNITION KILL When armed, the system can prevent the vehicle from being started. AUTO ARM AFTER TRIGERRING After the siren sounds for 30 seconds upon triggering, the system will remain armed. If the triggering signal is still present, the system will bypass that zone until the triggering signal returns to normal status. PARKING LIGHT FLASH In armed mode, the parking lights and dome light will flash for 30 seconds when the system is triggered. SIREN OUTPUT (See Function Selection 15) In armed mode, the siren or car horn will sound for 30 seconds when the system is triggered. FUNCTION SELECTION The function selections are programmable. Please follow these procedures: a. Disarm the system. b. Turn key from OFF position to ON position. c. Press valet button 7 times within 8 seconds. d. Turn key to OFF position, the LED will start to flash once per second. e. Press the valet button the same number of times as the function number you would like to change within 20 seconds. The siren will output a confirmation chirp each time the valet button is pressed. As a short cut for entering function 10, press and hold the valet button for 3 seconds, then release. The siren will chirp twice for confirmation. To enter 13, press and hold the valet button for 3 seconds, then release. You will hear 2 chirps. Then, press and release the valet button 3 more times. You will hear 3 chirps. To enter 25, press and hold the valet damage or personal injuries resulting from the use of the information. Installation by qualified automotive professionals is highly recommended. REV ST /6 2

3 button for (CONTINUED FROM PAGE 2) 3 seconds, then release. You will hear 2 chirps. Press and hold the valet button again for 3 seconds, then release. You will hear 2 more chirps. Then, press and release the valet button 5 times. You will hear 5 chirps. f. Turn key to the ON position. You will hear the siren chirp to indicate the current function status (1 or 2 chirps). Then turn key to the OFF position. The system will allow you to enter another selection by repeating step (e). g. To exit programming, turn key to the ON position and press the valet button one time. The system will exit the programming mode. DEFAULT VALUE (1CHIRP) VARIABLE VALUE (2CHIRPS) 1. /UN TIMER 0.5 SEC 3.5 SEC 2.UN PULSE SECOND UN WITH DISARM AFTER DISARM OUTPUT (HOLD BUTTON 2) 4. IGNITION CONTROLLED DOOR S ON OFF 5. SUPER SOFT CHIRP ARM WITH SHOCK SENSOR ON OFF 6. ARM/DISARM WITH CHIRP ON OFF 7. ANTI-CARJACKING ON OFF 8. LAST DOOR ARMING ON OFF 9. LAST DOOR ARMING WITH OFF ON 10. AUTO RE-ARM ON OFF 11. AUTO RE-ARM WITH OFF ON 12. VALET ON OFF 15. SOUND(siren/horn) CONTINUOUS OUTPUT PULSED OUTPUT 16. LAST DOOR ARMING ALL SENSOR INPUTS IGNITION INPUT INPUTS ACTIVATED ACTIVATED ONLY 25. DEFAULT YES 1. Lock/Unlock Timer Default: After pressing arm/disarm, both the lock and unlock outputs pulse for 0.5 seconds. Variable: After pressing arm/disarm, both the lock and unlock outputs pulse for 3.5 seconds. 2. Unlock pulse Default: 1 pulse Variable: 2 pulses 5. Super Soft Chirp with Shock Sensor Default: Arming with Super Soft Chirp, shock sensor will sound warning chirps on light impacts. Variable: Arming with Super Soft Chirp arms, shock sensor will NOT sound warning chirps on light impacts. 6. Arm/Disarm with Chirp Default: Arm/Disarm chirps ON. Variable: Arm/Disarm chirps OFF. 7. Anti-Carjacking Default: Anti-carjacking mode is ON. Variable: Anti-carjacking mode is OFF. 8. Last Door arming Default: Turn key to OFF position and close the last door. After 30 seconds, the system will arm automatically. Variable: Last Door Arming is off. 9. Last Door arming with Door Lock Default: Last door arming with door lock is off. Variable: Last door arming with door lock is on. Note: This feature will only work if the Last Door Arming function is selected ON. 10. Auto Re-arm Default: Auto Re-arm is on Variable: Auto Re-arm is off. 11. Auto Re-arm with lock Default: Auto Re-arm with lock is off. Variable: Auto Re-arm with lock is on. Note: This feature will only work if the Auto Re-arm function is selected ON. 12. Valet Mode Default: Valet mode is on. Variable: Valet mode is off. 15. Siren output Default: Continuous siren output. Variable: Pulsed siren output. 16. Last Door Arming Inputs Default: Last door arming with all sensors inputs activated. Variable: Last door arming with only ignition inputs activated. 25. Default Default: Return system to default values.. 3. Second unlock Default: Normal unlock with disarm. Variable: Seond unlock after disarm. 4. Ignition controlled door locks Default: When key turns from OFF position to ON position, doors will lock after 20 seconds. Variable: When key turns from OFF position to ON position, doors will NOT lock after 20 seconds (unlock only). damage or personal injuries resulting from the use of the information. Installation by qualified automotive professionals is highly recommended. REV ST /6 3

4 FOR VEHICLES WITHOUT DRIVER SIDE ING MOTOR GUN UN NO COM NC NO COM NC BROWN/BLUE ORANGE/BLUE BROWN/GREEN ORANGE/GREEN +12V BLUE GREEN ACTUATOR This system has a switch instead of an actuator in the drivers door. You will need to mount an actuator (GT series) in the drivers door to control your locks. Wiring diagram comes with actuator (GT series) 1. Install the fuse on the red wire then connect the BROWN/BLUE, BROWN/GREEN, and RED wires to a constant 12 volts. 2. From the keyless entry unit connect the ORANGE/BLUE, ORANGE/GREEN, and BLACK wires to metal ground. 3. Mount the actuator, and connect the and wires to the actuators green and blue wires. FOR VEHICLES WITH NEGATIVE ING SYSTEM Note: Connect black, brown/blue and brown/green wire to chasis ground. UN DOOR SWITCH Negative when lock NEGATIVE (SENDER) Negative when unlock AUTOLOC CL SERIES DOOR KITS CL CONTROL BOX BROWN WHITE BROWN/BLUE ST9000 Testing (w/an airbag safe digital volt-ohm meter) Connect the testlight wire to a ground (-), then probe all wires from your door lock switch to determine the lock, unlock, and sender wires. 1. If you come to a wire that S your doors when probed (-), then you have found the lock wire. Connect the wire from the keyless entry unit to this wire. 2. If you come to a wire that UNS your doors when probed (-), then you have found the unlock wire. Connect the wire from the keyless entry unit to this wire. 3. From the keyless entry unit connect the BROWN/BLUE and BROWN/GREEN wires to your sender wire. This wire will be a constant negative. 4. Install the fuse on the red wire then connect the RED wire to a constant 12 volts (+), and the BLACK wire to a body ground. FOR VEHICLES WITH POSITIVE ING SYSTEM UN DOOR SWITCH Positive when lock POSITIVE (SENDER) Positive when unlock Note: Connect red, brown/blue and brown/green wire to constant 12 Volts. Testing (w/an airbag safe digital volt-ohm meter) Connect the testlight wire to a 12 volts (+), then probe all wires from your door lock switch to determine the lock, unlock, and sender wires. 1. If you come to a wire that S your doors when probed (+), then you have found the lock wire. Connect the wire from the keyless entry unit to this wire. 2. If you come to a wire that UNS your doors when probed (+), then you have found the unlock wire. Connect the wire from the keyless entry unit to this wire. 3. From the keyless entry unit connect the BROWN/BLUE and BROWN/GREEN wires to your sender wire. This wire will be a constant positive. 4. Install the fuse on the red wire then connect the RED wire to a constant 12 volts (+), and the BLACK wire to a body ground. FOR VEHICLES WITH REVERSE POLARITY ING SYSTEM GROUND ORANGE/BLUE UN CUT 12V 12 Volts when pushed 12 Volts when pushed CUT GROUND Note: Connect red, brown/blue and brown/green wire to constant 12 Volts. ORANGE/GREEN Note: After cutting master door lock switch all buttons will be inoperable when lock button is activated. If only drivers door lock is inoperable, then wrong wire was clut. Similar to positive trigger, but will have 5 wires. 2 wires will be grounded, another 2 wires will be positive triggers, and 1 will have a constant 12 volts (sender wire). 1. Install the fuse on the red wire then connect the BROWN/BLUE, BROWN/GREEN, and RED wires to 12 volts. 2. From the keyless entry unit connect the BLACK wire to metal ground. 3. Cut the drivers door lock wire. This wire will have 12 volts when lock 4. Connect the ORANGE/BLUE wire to the switche's side of the lock wire. 5. Connect the wire to the motor's side of the lock wire. 6. Cut the drivers unlock wire. This wire will have 12 volts when unlock 7. Connect the ORANGE/GREEN wire to the switches side of the unlock wire. 8. Connect the wire to the motor's side of the unlock wire. damage or personal injuries resulting from the use of the information. Installation by qualified automotive professionals is highly recommended. REV ST /6 4

5 TO STARTER MOTOR TO IGNITION SIDE OF THE STARTER SHOCK SENSOR ADJUST DIAL ST9000 SECURITY SYSTEM LED ANTENNA OPTIONAL SENSOR See page 6. VALET SWITCH YELLOW BROWN/WHITE WHITE BROWN BLACK RED WHITE/RED ORANGE/BLACK 18AWG DOME INPUT ORANGE/BLACK 18AWG DOME OUTPUT ORANGE BROWN/GREEN 18AWG 18AWG ORANGE/GREEN 18AWG BROWN/BLUE 18AWG 18AWG ORANGE/BLUE 18AWG PURPLE 18AWG POSITIVE 12V CENTRAL ING INTERFACE CONNECTIONS TRUNK SIREN IGNITION SWITCH OFF ACC ON PURPLE/BLACK NEGATIVE CH4 GREEN/BLACK NEGTIVE CH3 YELLOW/BLACK NEGATIVE SECOND UN ORANGE/BLACK WINDOW UP NEGATIVE OUTPUT TRUNK TRIGGER FUSE 15A DOOR TRIGGER + FUSE 15A ORANGE RED BLACK DOOR TRIGGER + PARKING LIGHTS START + 12V + CUT STARTER MOTOR NEGATIVE PARKING LIGHTS OPTIONAL HEADLIGHT SWITCH a RELAY ORANGE (FROM ALARM) PARKING LIGHT OUTPUT NOTE: RELAY NOT INCLUDED damage or personal injuries resulting from the use of the information. Installation by qualified automotive professionals is highly recommended. REV ST /6 5

6 TECH SUPPORT: OPTIONAL ACCESSORIES USE THESE EXCELLENT ADD-ON ACCESSORIES TO ENHANCE YOUR VEHICLES SECURITY SYSTEM SIMPLE PLUG AND PLAY INSTALLATION LONG LIFE AND RELIABLE OPERATION COMPATIBLE WITH ALL STELLAR ALARMS BACKED BY A LIMITED LIFETIME WARRANTY UT1000 ULTRASONIC SENSOR GS1 GLASS SENSOR Get the ultimate in protection for your vehicle! This dual stage ultrasonic sensor package fills the cabin of your vehicle with invisible ultrasonic waves. Any intrusion that interrupts these invisible waves will trigger your alarm system. Installation is easy. Simply mount, wire, configure and you ar done! RM2000 RADAR SENSOR Upgrade your alarm system to the ultimate dual stage sensor. When an intruder comes near your vehicle the sensor will trigger a warning chirp. (Stage 1) If the sensor senses motion within the vehicle while your system is armed, it will trigger the alarm system (stage2). Sensitivity for both stages of detection is fully adjustable. BKSR BATTERY BACK UP SIREN This high frequency sensor will trigger your alarm system when the thief attempts to gain entry by breaking your windows. Fully compatible with all Stellar alarm systems with an optional sensor port. The GS1 glass sensor gives you added peace of mind at a small cost. PAGER LONG RANGE PAGER Full featured pager with multi-mode operation allows you to monitor the status of your vehicle's security. Ultracompact high output 4 watt system offers superior range while conserving batter usage. A handy belt holster (not shown) for the pager is included. Universal design, easy installation, and will work with all aftermarket or factory alarms. Employing the latest compact power cell technology. If the alarm system s power source has been disconnected, the siren will remain active and functional. The BKSR is housed in a weatherproof housing. Easy installation The Hoffman Group L.L.C. All rights reserved. REV ST /6 6