Coversio Istructios: QMS magicolor 2 DeskLaser to QMS magicolor 2 CX 1800502-001A
Trademarks QMS, the QMS logo, ad magicolor are registered trademarks of QMS, Ic., registered i the Uited States Patet ad Trademark Office. Proprietary Statemet The digitally ecoded software icluded with your QMS magicolor prit system is Copyrighted 1998 by QMS, Ic. All Rights Reserved. This software may ot be reproduced, modified, displayed, trasferred, or copied i ay form or i ay maer or o ay media, i whole or i part, without the express writte permissio of QMS, Ic. Copyright Notice These istructios are Copyrighted 1998 by QMS, Ic., Oe Magum Pass, Mobile, AL 36618. All Rights Reserved. These istructios may ot be copied i whole or i part, or trasferred to ay other media or laguage, without the express writte permissio of QMS, Ic.
Itroductio Itroductio This kit icludes all the hardware ad software ecessary for to covert a QMS magicolor 2 DeskLaser Prit System ito a QMS magicolor 2 CX Prit System. Kit Cotets I additio to these istructios, your upgrade kit cotais the followig items. Make sure that you have all of these items before proceedig with the istallatio. Report ay discrepacies to your QMS vedor. Do t retur ay merchadise before cotactig the vedor. QMS magicolor 2 CX cotroller board with 24 MB RAM istalled See the istallatio istructios i this documet. Ati-static wrist strap Product ID logo label (P/N 1241121-002) Two dataplate overlay labels (P/Ns 1241198-001 ad 1241202-001) QMS magicolor 2 Gettig Started (hardcopy) QMS magicolor 2 Documetatio CD-ROM See the isert booklet for istructios o istallig Adobe Acrobat Reader. See the 1CONTENT.PDF file i the root for cotets ad access iformatio. QMS Software Utilities CD-ROM See the isert booklet for istructios o istallig Adobe Acrobat Reader. See the 1CONTENT.PDF file i the root directory for cotets ad access iformatio. Warraty card QMS magicolor 2 DeskLaser to CX Coversio 1
Coversio Procedure Coversio Procedure Covertig your QMS magicolor 2 DeskLaser to a QMS magicolor 2 CX Prit System ivolves two steps: Removig the magicolor 2 DeskLaser cotroller board ad istallig the magicolor 2 CX cotroller board.» Note: You ll eed a Phillips screwdriver for this procedure. Applyig the appropriate idetificatio labels. Istallig the priter driver(s). Cautio: It s very importat to protect the priter cotroller board from electrostatic damage while performig this coversio. Attach oe ed of the ati-static wrist bad icluded i this kit to your wrist ad the other ed to ay coveiet electrical groud. The bare metal chassis of equipmet, such as o the back of a computer, is suitable if it is plugged i but tured off. Never attach the wrist strap to ay piece of equipmet with a electrical curret preset. Tur off all power switches first. Plastic, rubber, wood, paited metal surfaces, ad telephoes are ot acceptable groudig poits. The priter is t a acceptable groudig poit either because it must be uplugged before you perform this task. 2 QMS magicolor DeskLaser to CX Coversio
Coversio Procedure Istallig the magicolor 2 CX Cotroller Board Cautio: The followig procedure is writte for the system admiistrator. Do ot attempt this procedure if you have o experiece workig with circuit boards. 1 Tur off the priter, remove the power cord, ad discoect all iterface cables from the priter. 2 Usig a Phillips screwdriver, loose the two moutig screws that hold the cotroller board to the priter. 3 Pull the magicolor 2 DeskLaser cotroller board straight out ad lay it o a flat surface. 4 Remove from its packagig the magicolor 2 CX cotroller board. 5 If you wat to, remove ay SIMMs from the magicolor 2 DeskLaser cotroller board, ad istall them o the magicolor 2 CX cotroller board. The magicolor 2 CX cotrol board comes stadard with 24 MB of memory. It s ot ecessary to add additioal memory, but you may wat to. Refer to the QMS magicolor 2 Optios maual for SIMM removal ad istallatio istructios. 6 Remove from their packagig ay SIMMs you purchased separately ad istall them o the magicolor 2 CX cotroller board. Agai, it s ot ecessary to add additioal memory, but you may wat to. Refer to the QMS magicolor 2 Optios maual for SIMM istallatio istructios. 7 If you purchased ay other optios, such as a iteral hard disk, istall them ow. Refer to the QMS magicolor 2 Optios maual for istructios. QMS magicolor 2 DeskLaser to CX Coversio 3
Coversio Procedure 8 Alig the magicolor 2 CX cotroller board o the plastic guides, ad the slide it ito the priter. Make sure it s properly seated i its coectors, but do ot force it. 9 Tighte the two moutig screws. 10 Recoect the iterface cables ad power cord, ad the tur o the priter. Verifyig the Coversio To verify the coversio, tur o the priter. A start-up page, idetifyig the priter as a QMS magicolor 2, automatically prits. This idicates that the priter has successfully bee coverted from a QMS magicolor 2 DeskLaser to a QMS magicolor 2 CX Prit System. Applyig the Idetificatio Labels Use the followig illustratios to istall the ew dataplate ad product ID logo o the priter. Product ID Logo QMS magicolor 2 Product ID Logo P/N 1241121-002 (Apply over the existig product ID logo.) 4 QMS magicolor DeskLaser to CX Coversio
For More Iformatio... Dataplate» Note: The dataplate illustrated here is for 110 volt priters. If you have a 220 volt priter, discard overlay P/N 1241202-001 (there is o FCC ID lie o the dataplate). I additio, the Model ame for 220 volt priters eds with a -2 rather tha a -1. Model: QMS-MCWX2-1 Ratig: 120V 50Hz-60 Hz, 8A FCC ID: E7SMC2WX-1 SN: P U Pa Pa Th Pa (1) this u MCCX2 Model overlay P/N 1241198-001 MC2 FCC ID overlay P/N 1241202-001 Istallig the Priter Driver(s) Refer to your QMS magicolor 2 Gettig Started maual, shipped i this coversio kit, for complete iformatio o istallig the appropriate priter driver(s). For More Iformatio... If you have ay questios or problems durig or after the coversio, refer to appedix A, QMS Customer Support, i ay QMS maual to fid out how to cotact QMS. v QMS magicolor 2 DeskLaser to CX Coversio 5