XCM Cross Fire Converter 3.0 (ver 2.1 ) Usage manual --------------------------------------------------------------------- Before using the product, read this manual carefully and retain it for future reference. --------------------------------------------------------------------- Product feature: XCM Cross Fire Converter 3.0 is an adapter that allows you to connect your Xbox one /PS3 /Xbox 360 wired/wireless controller to your PS4 console. Built in Rapid fire function. Support firmware update via PC. Plug and play. Support button mapping. Can map multi-keys function into one key. (with this Marco programming, you are able to program special modes like: auto drop shot, auto burst, active reload, sniper breath, super aim, quick scope etc for FPS games. Regarding to different FPS games with different setting, you are able to program without waiting for the new marco program from the PC),and of course -no need to modify or solder your controller and console. Device introduction:
<1> USB port Connects to PS 4 console. <2> USB port. PlayStation 4 wired controller port (connect via charging cable) <3>Rapid Fire/Turbo Switch ON---High Speed Firing(30 shots per second) OFF---Normal (off) <4> Update Button Use to update new firmware via PC <5> Update LED indicator <6>USB Port Xbox 360 or Xbox one or PS3 / Xbox 360 PC Wireless Gaming Receiver How to connect: Note: The Official WIRED PlayStation 4 Dualshock 4 controller (with charge cable) must be required to use on XCM Cross Fire Converter 3.0. The steps are shown below:
1. Plug the DualShock4 wired controller (with charge cable) to the XCM Cross Fire Converter 3.0 2. Connect XCM Cross Fire Converter 3.0 to PlayStation 4, and wait until the light bar on the DualShock4 lights up in blue, the connection is successful. 3. Plug in the Xbox one /PS3 /Xbox 360 wired/wireless controller ; 4. PS4 Dual shock 4 wired controller (with charge cable) must be connected to Cross fire converter 3.0 during gameplay. Default configuration chart: The default buttons mapping to PS 4 TM /Xbox 360 TM /PS 3 TM / Xbox one TM controller, is shown on the table below Re-mapping the button: A. Single button re-mapping a. If you want to remap the RT button to the RB button on your Xbox One controller. Press the P key <4> once and wait until the P key <5> LED indicator lights up, now press the RT button, and press the P key <4> again, the P key <5>LED indicator blinks, press the RB button now, the P key <5> LED indicator lights off, the RB button functions has been set to the RT button function, the original function of the RB button will be temporarily replaced by the RT function, the function of the RT button will still be the same.
b. If you want to erase the setting on the RB button Press the P key <4>once and wait until the P key LED indicator <5> lights up, now press the RB button, then press the P key<4> again, the P key LED indicator <5>blinks, press the RB button now, the P key LED indicator<5> lights off,the RB button restores to its original function. c. Exchange the RT and RB function: 1. Press the P key <4> once and wait until the P key LED indicator<5> lights up, press the RB button, and press the P key <4> again, the P key LED indicator <5> blinks, press the RT button now, the P key LED indicator <5>lights off. 2. Press the P key<4> once and wait until the P key LED indicator <5> lights up, press the RT button, press the P key <4> again, the P key LED indicator <5>blinks, press the RB button now, the P key LED indicator <5> lights off, you had just exchanged the RT and RB function. B. Mapping multi-keys function to a single key. a. If you want to map the A,B,X, 3 buttons on the Xbox One controller to the RT button. You will have to press the P key <4> once and wait until the P key LED indicator <5>lights up, now press the A,B,X 3 buttons on xbox One controller in proper order then press the P key <4> again, the P key LED indicator <5> blinks, press the RT button on the controller, the P key LED indicator <5> turns off. Now if you press the RT key (on the controller) it s the same as pressing down A,B,X, 3 buttons simultaneously.
b. Remove this combo mapping mode on the RT button. Step: Press the P key <4> once and wait until the P key LED indicator <5>lights up, press the RT button, and press the P key <4> again, the P key LED indicator <5> blinks, press the RT button again, the P key LED indicator <5> is now turned off, you have now removed the settings on the RT button. If you want to erase all the custom setting, press and hold the P key for 3 sec the P key LED indicator <5> blinks, release the P key, the P key LED indicator turns off, all of the custom setting are removed. XCM Cross Fire Converter 3.0 firmware can be upgraded via PC. More information can be found on www.maxbuy.cc and www.xcm.cc