60, 8007 NAMUR /, / and / Directional control valves Modular NAMUR design Actuation: electromagnetic Indirectly controlled spool valves Port size: G / For single and double operated actuators Standard manual override with detent Compact design High flow rate Simple design of soft spool seal system Maintenance-free Easily interchangeable solenoid system Exhaust air recirculation The solenoids are ATEX approved (see solenoids page ) Valves and solenoids are ATEX approved Technical data Medium: Solenoid valve for filtered, lubricated *) or non-lubricated air Operation: Solenoid, Flow direction: Fixed Mounting position: Optional, preferably with solenoid on top Nominal size: 6 Port size: G / Electrical connection: See solenoid table Operating pressure: to 8 bar Temperature: -0... 0 C Please consult our technical service for use below + C. If installed in the open protect all connections against the penetration of moisture! Materials: Housing: Aluminium Pilot flange: Plastic Seat seal: NBR (Perbunan) Ordering information / directional control valve, connection G /, solenoid V DC, protection class IP6 Part No.: 800777.06.0.00 Connector: 0707 Connections See data sheet N/UK 7.7.00 / / 0 *) Oil recommendation: Shell Hydrol DO, Esso Febis (as of July 99) or comparable oils with DVI values < 8 (DIN ) and ISO viscosity class -6 (DIN 9). /0 N/UK..0.0
60, 8007 NAMUR General information Symbol 0 Type* Port size, () () Actuation Nominal size Operating kv-value pressure (bar) (Cv (US) kv x,) Weight (kg) 800777 G / Flange Solenoid 6... 8, 0, Dimensions Nr. 6077 G / Flange Solenoid 6... 8, 0, 677 G / Flange x Solenoid 6... 8, 0,9 * When ordering please indicate solenoid, voltage and current type (frequency). Port not throttleable. /- or / way function (Conversion Instruction see page 6) Symbol 0 Type* Port size, () () Actuation Nominal size Operating kv-value pressure (bar) (Cv (US) kv x,) Weight (kg) 6079 G / Flange Solenoid 6... 8, 0, Dimensions Nr. 679 G / Flange x Solenoid 6... 8, 0,9 * When ordering please indicate solenoid, voltage and current type (frequency). Port not throttleable. Solenoid actuators Type Power consumption Rated current at Protection class Temperature Weight Dimensions Circuit V DC 0 V AC V DC 0 V AC Fluid max. Ambience diagram (W) (VA) (ma) (ma) ( C) (kg) No. No. 00 *),7,6/, IP 6-0... +0 0,06 6 with connector DIN EN 70-80 Form B *6) 06 *),6, 0 IP 6-0... +0 0, 7 with connector DIN EN 70-80 Form A *6) 06 *),7 Cat. IIG, EEx m II T -0... +0 0, 8 m cable 06 *), 9 Cat. IIG, EEx m II T -0... +0 0, 8 8 m Kabel 07,7 IP 66-0... +0 0, 9 8 Connector Mx DIN EN 6097-- Anh. D Standard voltages V DC, 0 V AC. Other voltages on request. Design acc. to VDE 080, EN 00/008. 00% duty cycle. *) Required connector, see page *) Certificate of Conformity PTB No. PTB 0 ATEX 0 X *6) Connector is not indicated in delivery N/UK..0.0 /0
60, 8007 NAMUR Accessories Silencer Connectors Flange plate Yoke 00600 (G/) *) 0707 Form A 06790 NAMUR sigle connection plate 009 068000 Form B 0679 NAMUR rip use in combination with 06790 ( Alu) *) For indoors use Basic dimensions for valves ➀ 6 G/ ø 9, M ø, ø, 6 ø9, ø, 7 0 ➁ 6 G/ ø,, M ø9, ø, 7 0 Solenoid 90 turnable Manual override /0 N/UK..0.0
60, 8007 NAMUR ➂ 6 G/ M ø,, ø9, ø, 7 0 ➃ 6, G / ø ø, ø 9, M 7 Solenoid 90 turnable Manual override N/UK..0.0 /0
60, 8007 NAMUR ➄ 6 ø, G / ø ø 9, M Solenoid 90 turnable Manual override Dimensions for solenoid operators ➅ ➆ 9 6 9, 6 7 0 9, Ø9 Ø9 ➇ ➈ 9 8, 0 Mx 9, 9,, 9, ~ 6 /0 N/UK..0.0
60, 8007 NAMUR Circuit diagrams ➀ ➇ NAMUR hole pattern M Port (A) Coding stud threaded M (0 deep) Port (R) Conversion instructions of / into / way function / way function (original mode of supply) / way function / / 7 6 7 6 / resp. / way function can be achieved just by swapping enclosed adaptor plates. Make sure Marker and Arrow do match as shown on above drawing. Original mode of supply: / function. 6 arrow 7 Marker Warning These products are intended for use in industrial compressed air systems only. Do not use these products where pressures and temperatures can exceed those listed under Technical Data. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not within published specifications, consult NORGREN. Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure. System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided. System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products where applicable. N/UK..0.06 /0