1. Effective voltage is given by expression

Similar documents
Circuits with inductors and alternating currents. Chapter 20 #45, 46, 47, 49

EDEXCEL NATIONAL CERTIFICATE/DIPLOMA UNIT 5 - ELECTRICAL AND ELECTRONIC PRINCIPLES NQF LEVEL 3 OUTCOME 4 - ALTERNATING CURRENT

Physics 6C, Summer 2006 Homework 2 Solutions

Chapter 35 Alternating Current Circuits

Inductors in AC Circuits

Diodes have an arrow showing the direction of the flow.

BASIC ELECTRONICS AC CIRCUIT ANALYSIS. December 2011

First Year (Electrical & Electronics Engineering)

AC Generators. Basic Generator

2. A conductor of length 2m moves at 4m/s at 30 to a uniform magnetic field of 0.1T. Which one of the following gives the e.m.f. generated?

Lecture 24. Inductance and Switching Power Supplies (how your solar charger voltage converter works)

Application Note. So You Need to Measure Some Inductors?

Experiment #11: LRC Circuit (Power Amplifier, Voltage Sensor)

Impedance Matching and Matching Networks. Valentin Todorow, December, 2009

RLC Resonant Circuits

W03 Analysis of DC Circuits. Yrd. Doç. Dr. Aytaç Gören

Line Reactors and AC Drives

Properties of electrical signals

SERIES-PARALLEL DC CIRCUITS

Homework # Physics 2 for Students of Mechanical Engineering

CURRENT ELECTRICITY INTRODUCTION TO RESISTANCE, CAPACITANCE AND INDUCTANCE

Alternating Current Circuits and Electromagnetic Waves

The W5JCK Guide to the Mathematic Equations Required for the Amateur Extra Class Exam

Physics 2102 Lecture 19. Physics 2102

Chapter 12: Three Phase Circuits

Induced voltages and Inductance Faraday s Law

RLC Series Resonance

Chapter 29 Alternating-Current Circuits

Energy in Electrical Systems. Overview

45. The peak value of an alternating current in a 1500-W device is 5.4 A. What is the rms voltage across?

Module Title: Electrotechnology for Mech L7

DOE FUNDAMENTALS HANDBOOK ELECTRICAL SCIENCE Volume 3 of 4

Three phase circuits

Chapter 10. RC Circuits ISU EE. C.Y. Lee

Lab E1: Introduction to Circuits

Slide 1 / 26. Inductance by Bryan Pflueger

Critical thin-film processes such as deposition and etching take place in a vacuum

The full wave rectifier consists of two diodes and a resister as shown in Figure

104 Practice Exam 2-3/21/02

Apprentice Telecommunications Technician Test (CTT) Study Guide

Understanding Power Impedance Supply for Optimum Decoupling

Chapter 11. Inductors ISU EE. C.Y. Lee

L and C connected together. To be able: To analyse some basic circuits.

Eðlisfræði 2, vor 2007

Power measurement in balanced 3 phase circuits and power factor improvement. 1 Power in Single Phase Circuits. Experiment no 1

MULTIPLE CHOICE. Choose the one alternative that best completes the statement or answers the question.

Chapter 12 Driven RLC Circuits

12. The current in an inductor is changing at the rate of 100 A/s, and the inductor emf is 40 V. What is its self-inductance?

Rectifier circuits & DC power supplies

Application Guide. Power Factor Correction (PFC) Basics

ε: Voltage output of Signal Generator (also called the Source voltage or Applied

BSNL TTA Question Paper-Instruments and Measurement Specialization 2007

Equipment: Power Supply, DAI, Variable resistance (8311), Variable inductance (8321)

Series and Parallel Circuits

Equipment: Power Supply, DAI, Transformer (8341), Variable resistance (8311), Variable inductance (8321), Variable capacitance (8331)

Power Supplies. 1.0 Power Supply Basics. Module

Chapter 25 Alternating Currents

Network Theory Question Bank

Chapter 30 Inductance, Electromagnetic Oscillations, and AC Circuits. Copyright 2009 Pearson Education, Inc.

Alternating-Current Circuits

12. Transformers, Impedance Matching and Maximum Power Transfer

Measuring Impedance and Frequency Response of Guitar Pickups

Current and Temperature Ratings

Let s examine the response of the circuit shown on Figure 1. The form of the source voltage Vs is shown on Figure 2. R. Figure 1.

EE301 Lesson 14 Reading: , , and

Direction of Induced Current

Electrical Resonance

Iron Powder Cores for Switchmode Power Supply Inductors. by: Jim Cox

Inductors & Inductance. Electronic Components

CHAPTER 28 ELECTRIC CIRCUITS

Aircraft Electrical System

Design Considerations for an LLC Resonant Converter

RUPHYS ( RUPHY227F2015 ) My Courses Course Settings University Physics with Modern Physics, 14e Young/Freedman

Designing Stable Compensation Networks for Single Phase Voltage Mode Buck Regulators

UNDERSTANDING AND CONTROLLING COMMON-MODE EMISSIONS IN HIGH-POWER ELECTRONICS

Effect of Frequency on Inductive Reactance

HOW TO SELECT VARISTORS

Electricity & Electronics 5: Alternating Current and Voltage

How To Understand And Understand The Theory Of Electricity

7. What is the current in a circuit if 15 coulombs of electric charge move past a given point in 3 seconds? (1) 5 A (3) 18 A (2) 12 A (4) 45 A

LR Phono Preamps. Pete Millett ETF.13.

Experiment 8: Undriven & Driven RLC Circuits

CHAPTER 30: Inductance, Electromagnetic Oscillations, and AC Circuits

Understanding Power Factor and How it Affects Your Electric Bill. Presented by Scott Peele PE

Measuring Biased Inductors with the GenRad Digibridge

Objectives. Capacitors 262 CHAPTER 5 ENERGY

Q1. The graph below shows how a sinusoidal alternating voltage varies with time when connected across a resistor, R.

PHYS 222 Spring 2012 Final Exam. Closed books, notes, etc. No electronic device except a calculator.

Basics of Electricity

EE 1202 Experiment #4 Capacitors, Inductors, and Transient Circuits

DIODE CIRCUITS LABORATORY. Fig. 8.1a Fig 8.1b

Impedance Matching. Using transformers Using matching networks

Diode Applications. by Kenneth A. Kuhn Sept. 1, This note illustrates some common applications of diodes.

Fundamentals of Signature Analysis

Semiconductor Diode. It has already been discussed in the previous chapter that a pn junction conducts current easily. Principles of Electronics

Capacitors in Circuits

People s Physics Book

= V peak 2 = 0.707V peak

CHAPTER 31. E max = 15.1 V

Transcription:

Chapter 07 A C CIRCUITS

1. Effective voltage is given by expression 1) Ve = Vo/ 2 2) Ve = 2 Vo 3) Vo/π 4) π Vo Effective voltage isrms voltage Answer is (1)

2. A coil having zero resistance is connected in series with a 90Ω resistance and the combination i is connected to 120V, 60 Hz line. A voltmeter reads 36 V across the resistance and 114 V across the coil. The self inductance of the coil is 1) 0.076 H 2) 0.76 H 3) 7.6 H 4) 76 H

Given V R = 36 V R = 90 Ω I = V/R =36/90 = 0.4 A Also given V L = 114V X L = V L /I 2πυL = 114/0.4 L = 114/2x3.14x60x0.4 = 0.76 H

3. A radio transformer has 660 turns of wire in the primary coil which is connected to 220 V AC source. The secondary coil supplies 6.3V 63V for the filament of a bulb. What is the number of turns in the secondary? 1) 2 2) 4 3) 19 4) 57

Ns/Np = Vs/Vp Ns = Vs Np /Vp = 6.3 x660 / 220 = 6.3x 3 =18.9 =19

4. A current of 4A flows in a coil when connected to a 12 V dc source. If the same coil is connected to a 12V, 50 rad s 1 ac source, acurrent of 2.4 A flows. The inductance of the coil is 1) 80 H 3) 80 mh 2) 8 H 4) 8 mh.

I dc = 4A V dc = 12 V R = V dc / I dc = 12 /4 =3Ω V ac = 12V, I ac = 2.4 A Z = V ac / I ac = 12 /2.4 =5Ω ω= 50 rad s 1 L = ( Z 2 R 2 ) / ω = 4/50 =0.08 = 80 mh

5. An a.c. having a peak value 28 A is used to heat a metal wire. To produce the same heating effect a constant tcurrent I that t can be used is 1) 28A 2) about 20A 3) 7A 4) about 10A Answer : Idc = Irms = Io / 2 = 28/1.41 =20 A

6. A circuit has a resistance of 30 Ω in series with an inductive reactance of 40 Ω. They are connected in series with an ac source. If the peak value of current is 1 A and the peak voltage is 220 V, the power consumed by the circuit is 1) 66 W 2) 6.6. W 3) 0.66 W 4) 33 W

R=30 Ω X L = 40 Ω. Z= (R 2 + X L 2 )= 50Ω P = ½ (VoIo cos φ) = ½ VoIo (R/Z) = ½ x1x 220 x0.6 = 66 W Answer is ( 1)

7. In the circuit shown V AB = V AC, then P is 1) an inductor 2) a capacitor 3) a suitable combination of inductor and capacitor 4) resistor

V BC = 0 It is possible iff X is a combination L & C at resonance

8. In an ac circuit, the voltage V and the current I are given by V = 100 sin ( 100 πt t ) volt and I = 100 sin ( 100t + π/3 ) ma. The power dissipated in the circuit is 1) zero 2) 10 3) 5 W 4) 2.5 W

P = ½(VoIo cos φ) = ½(100x100x10-3 cos 60) = ½ x10x0.5 = 2.5 W

9. In a series LCR circuit, it R = 100 Ω and applied ac voltage is 200 V. When the capacitance alone is removed, the voltage leads the current by 30 0. When the inductance alone is removed, the voltage lags the current by 30 0. Then the current in the circuit is 1) 0.5 A 2) 1 A 3) 2A 4) 4 A

Net phase difference between V & I φ= φ 1 + φ 2 = 30 30 = 0 So ckt is in resonance I = V/R = 200/100 = 1 A

10.A 4 µf capacitor charged to 50 V is connected across an ideal inductor of inductance 10 mh. The maximum value of current in the circuit is 1) 20 ma 2) 2 ma 3) 1 ma 4) 1 A

Given, C = 4 µf V= 50 V 3 L = 10 x 10 3 H. Energy stored in the capacitor is converted into energy in the inductor ½ LI 2 = ½ CV 2 ½ x 10 x 10 33 I 2 = ½ 4x 10 66 x 2500 I 2 = 1 Answer is (4) = 1 A

11.A transformer is used to light 140 watt, 24 volt lamp from 240 V ac mains. The current in the main cable is 0.7 A. The efficiency of the transformer is 1) 63.8% 2) 84% 3) 83.3 % 4) 48%

Given ; Ps =140 watt, Vs=24 volt Vp = 240 V Ip= 0.7 A. The efficiency of the transformer η = Ps/Pp η = Ps/Vs Is =140/(24 x0.7) = 20/24 = 0.833 Answer is (3) = 83.33 %

12.In a LRC circuit, capacitance is changed from C to 2C. For the resonant frequency to remain unchanged, the inductance should ldbe changed from L to 1) 4L 2) 2L 3) L/2 4) L /4

For the resonant frequency to remain unchanged LC = const Lα1/C If C ---------2C, then L--------- L/2 Answer is ( 3) = L/2

13.An ac source E = 200 2 sin 100t is connected across a circuit containing a AC ammeter and a capacitor of capacity 1µ F. Then the reading of the ammeter is 1) 10mA 2) 20mA 3) 40mA 4) 80mA

E = 200 2 sin 100t comparing with E = Eo sin ωt Eo = 200 2 & ω = 100 Reading of the ammeter I = E/Xc I = Eo/ 2 Xc = 200 x ω C = 200x100 X10 6 = 2X10 2 = 20X10 3 A Answer is (2) = 20mA

14.The impedance of a coil of resistance R to AC of frequency 50Hz is 3R. The self inductance of the coil is (if R = 6.28Ω) 1) 0.25 H 2) 2.5 H 3) 0.028 H 4) 0.025 H

Z = 3 R υ= 50Hz &R = 6.28Ω L = ( Z 2 R 2 ) / 2πυ = ( 3R 2 R 2 ) /2πυ = 2 x R / 2πυ = 2 x6.28 /2x 3.14 x50 =1.41/50 = 0.0282 H Answer is (3)

15.The reactance offered by a coil to AC of certain frequency is equal to its resistance. The phase difference between the voltage across the coil to the current through the coil in radians is 1) π/3 2) π/6 3) π/2 4) π/4

Given X L =R Thephasedifference between thevoltage across the coil to the current through the coil tan φ = (X L Xc)/R =X L /R = 1 Φ = π/4/ Answer is 4) π/4

16.The choke coil has a resistance 8 Ω and the inductive reactance 6 Ω. The power factor of the coil is 1) 06 0.6 ` 2) 08 0.8 3) 0.4 4) 0.3

Given, R =8 Ω X L = 6 Ω. The power factor of the coil, Cos φ = R/Z =8/10 = 0.8 Answer is (2) = 0.8

17.An alternating current is given by I= I 1 cos wt + I 2 sin wt. the rms current is given by n

φ Io = (I 2 +I ) 12 2 2 +2 I 1 I 2 cosφ) but) φ=90 0 Io = (I 2 +I 2 12 22 ) Irms = Io/ 2 = (I 2 +I 2 12 22 )/2 Answer is

18.In the circuit shown, the inductor used is an ideal one. The current in the circuit when the switch is closed is 1) 0.2 A 2) 0.3 A 3) 1 A 4) 0.14 A

Since the inductor is ideal, the circuit can be written as I = E/(R e +r) I =10/10 = 1A Answer is (3) I = 1A

19.Reciprocal of impedance is called 1) conductance 2) admittance 3) conductivity 4) resistivity Answer is (2)

20.In an ac circuit the virtual power is 50 W and the power factor is ½. Then the actual power is 1) 50 W 2) 100 W 3) 25 W 4) 75 W

P av = VI cosφ P av = P vir cosφ P av = 50 x ½ Answer is (3) = 25 W

21.The primary of a transformer has 1000 turns and secondary has 2000 turns. For any input voltage, the power in the secondary is 1) double that in primary 2) less or equal to that in primary 3) half of that in primary 4) 15times 1.5 that in primary Answer is (2)

22.In an AC circuit containing a pure inductor and a capacitor, the current and voltage are 1) in phase 2) out of phase by 90 0 3) out of phase by 180 0 4) out of phase by 45 0 Answer is (1)

23.The band width of a resonance curve with respect to a series RLC circuit is 48 khz. If the quality factor is 3, the resonant frequency is 1) 51 khz 2) 45 khz 3) 144 khz 4) 16 khz

Q = υ o / BW Given, B.W = 48 khz. Q= 3 υ o = Q xbw = 3x 48 khz. = 144 khz Answer is (3) = 144 khz

24.An inductor of inductance 2 H and a resistance of 10 Ω are connected to a battery of 5 V in series. The initial rate of change of current is 1) 0.5 A /s 2) 1.25 A/s 3) 2.5 A/s 4) 2 A/s

Given : L = 2 H and a resistance of 10 Ω are connected to a battery of 5 V in series. The initial rate of change of current is Applying kirchof s loop rule to the ckt E L.(dI/dt) = IR Initially, I = 0 di/dt = E/L = 5/10= 0.5A/s Answer (1) = 0.5 A /s

25.A bulb B and a capacitor C are connected to a battery as shown in figure. When the switch S is closed. 1) the bulb will glow when the capacitor fully gets charged. 2) the bulb glows during charging of the capacitor. 3) the bulb will not glow at all 4) the bulb glows intermittently due to to the charging and discharging of the capacitor.

Bulb glows only when current flows through thecircuit circuit. In the given circuit, current flows during charging and discharging of the capacitor. When the switch S is closed, the process is charging Hence the answer is (2) = the bulb glows during charging of the capacitor

27.Which of the following statements is not true at the resonant frequency of a series LCR circuit. 1) inductive reactance = capacitive reactance 2) resonant frequency is independent of resistance 3) current in the circuit is minimum 4) impedance is purely resistive in nature. Answer is (3)

26. The inductance of a coil is 5H.What is its effective reactance in dc circuit? 1)0 2) infinity 3) 5Ω 4)0.2Ω For DC, frequency υ = 0 but X L =2πυL = 0 Answer is (1)

28.Power in an ac circuit depends on (A) rms value of voltage (B) rms value of current (C) phase difference between voltage and current 1) Only A is correct 2) Only B is correct 3) Both A & B are correct 4) All A,B & C are correct

Power in an ac circuit P = (V rms I rms cos φ) Answer is (4)

29.Which h of the fallowing has the dimension i of resistance R (υis the frequency of AC) 1)υC 2) =2πυL 3) C/υ 4) L/υ [ R] = [ X L ] but X L =2πυL [ R] = [υl ]

30. For long distance transmission, the AC is stepped up because transmission at high voltage is 1) faster 2) economical 3)not damped 4)not dangerous Transmission power loss P = I 2 R As V increases I decreases P decreases. So transmission at high voltage is economical. Answer is (2)

Transmission power loss P = I 2 R As V increases I decreases P decreases transmission at high voltage is economical. Answer is (2)

31.The transformer varies theoutput 1) Energy 2) Power 3) Frequency 4) Current Answer is (4) = current

32.The core of the transformer is laminated to 1) reduce eddy current 2)reduce self induction 3)increase the efficiency 4)decrease theweight ofthetransformer transformer Answer is (1)

33.Iron core decreases the loss of energy due to 1)heating 2) eddy currents 3)flux leakage 4)hysteresis Answer is (4)

34. The AC cannot be used for 1) heating 2) lighting i 3) electrolysis 4) generate mechanical energy Answer is (3)

35.What is the average value of ac over a complete cycle? 1)zero 2)I o / 2 3)2I o /π 4) 2I o Answer is (1)

36. The power factor varies between 1)zero to 0.5 2)0.5 to 1 3)zero to 1 4)1 and 2 Ans ; PF = cos φ which varies from 0 & 1

37.How does the current in an RC circuit vary when the charge on the capacitor builds up? 1)It increases linearly 2)It increases exponentially 3)It decreases linearly 4)It decreases exponentially Answer is (4)

38.The frequency of ac is 50Hz. How many timesinonesecond in second does thevoltage inthe current does becomes zero? 1)25 2)50 3)100 4)150 Answer is (3)

39.Why 220V ac is more dangerous than 220V dc? 1) The dc attracts 2)Peak voltage for ac is much larger 3)The body offers less resistance to ac 4) Due to some other reason Answer is (2)

40.What is the nature of graph between inductive reactance and frequency of ac for series RCL circuit? 1)Straight line 2)Parabola 3)Hyperbola 4)Bell shaped Answer is (1)

X L =2πυL It is of the form y = mx which is a Straight line passing through the origion with slope m= 2πL Answer is (1)

41. The impedance of a 10microfarad capacitor for 50 rad/s ac is 1)2 Ω 2) 20Ω 3) 200Ω 4) 2000Ω

The impedance Xc = 1/ ωc Xc = 1/ (50x10x10 66 ) =2000Ω Answer is (4)

42. A 1.0mH inductance a 10µF capacitance and a ac source. It is found that the inductor and the capacitor show equal resistances. The reactance should be nearest to 1)100Ω 2)32Ω 3)10Ω 4)3.2Ω

The circuit is in resonance. But resonant frequency ω = 1/ LC ω = 1/ 1x10-3 X10x10-6 = 10 4 X L = ω L = 10 4 x10-3 = 10 Answer is (3) =10Ω

43. In a circuit resistance R, capacitance C, and inductance L are in series with a sinusoidal power source. If the voltage across R, C and L are 80V, 10V and 70V respectively, then the voltage across the source terminals will be 1)100V 2)110V 3)140V 4)160V

V 2 = V R2 2 +(V C V L ) = 80 2 + (10 70) 2 = 80 2 + 60 2 = 100 2 V = 100V Answer is (1) = 100V

44. The inductance of a coil is 5H.What is its effective reactance in dc circuit? 1) 0 2) infinity 2) 3) 5Ω 4) 0.2Ω X L = ω L = 0xL = 0 Answer is (1)

45. For a choke coil the resistance is R and reactance is X. Which of the following relations is valid? 1) RX 2)R=X 3)R X 4)RX Answer is (4)