60-506-319.5 Crystal Smoke Detector Two 9V Duracell 9V 1. Twist counter-clockwise until detector become loose from base. 2. Replace batteries observing correct polarity. 3. Replace detector by twisting clockwise until it locks into place. TX-6010-01-1 Smoke Duracell 123, Panasonic CR123A Sanyo CR123A 1. Remove the battery from the base by turning counterclockwise. 2. Slide the battery compartment cover towards the outside of the unit. Lift the cover off. 3. Observing correct polarity, replace batteries and compartment 4. Line up notch on outside of unit and turn arrow on the base, turn clockwise. 60-848-02-95 Wireless Smoke Detector Two Duracell 123 Panasonic CR123A Sanyo CR123A 1. Remove unit from the base by turning counter-clockwise. 2. Slide the battery compartment cover towards the outside of the unit. Lift the cover off. 3. Observing correct polarity, replace batteries and the compartment 4. Line up notch on the outside of the unit and the arrow on the base, turn clockwise. 60-460 Heat 9V 1. Twist counter-clockwise until detector become loose from base. 2. Remove existing battery and replace. 3. Line up notch on outside of unit and the base and turn clockwise. 61-606-319.5 60-659-95R 4-Button Key Fob 12V 33mhA 60-694-95R 5-Button Key Fob 12 V 33mhA 60-607 2-Button Key Fob 12 V 33mhA GE Wireless Battery List Page 1 of 5
60-741-95 Micro Recessed Not Replaceable Battery has a 10-year lifespan. RF-1510-01 Recessed Door Lithium CR23 Panasonic CR23 1. Remove the cover by inserting a flat blade of a small screwdriver at the notched location on the cover to pop it off. 2. Slide the circuit board out from the case. Norte that it fits inside a channel on the inside of the case and be sure to put it back the same way for proper fit. 3. Install battery, observing correct polarity. 4. Replace circuit board into case. 5. Replace cover (snap fit). TX-1510-01 Recessed Door Lithium CR2032 Coin Battery (5-8 year lifespan) 1. Unscrew the top of the contact. 2. Carefully pull the circuit board out of the case. Before removing, notice that it fits inside a channel on the inside of the case. DO NOT pull out by the antenna wire! 3. Slide the battery onto the circuit board unit with the plus (+) side up. 4. Slide the circuit board back into the case. Make sure it slides back into the channel guides for a proper fit with the tamper switch facing up. 5. Screw top back on the contact. 60-670-95R Energizer AAA Duracell AAA 3. Observing the correct polarity, replace batteries. 60-362N CR123A/DR123A (5-10 year lifespan) 3. Observing correct polarity, replace batteries. GE Wireless Battery List Page 2 of 5
60-362 60-641 3.6 ½ AA Lithium 3. Observing correct polarity, replace batteries. TX-8010-01-1 Overhead Door Lithium CR2032 Coin Battery (5-8 year lifespan) 1. Remove cover from base by pressing a flathead screwdriver into the slot on the bottom and turning 90 degrees. 2. Place small flathead screwdriver in the slot between the metal clip and the battery and twist slightly, holding back one of the black plastic edges holding the battery. 3. Replace the battery with the + side facing out. 4. Replace sensor cover on the base by aligning the tamper switch with the plastic tamper tab and snap into place. 60-807-95R Wireless Motion 1. Push the button on top of the sensor to detach from the mounting plate. side. Pull to remove 3. Remove batteries, and observing the correct polarity, replace batteries. 60-703-95 Crystal Wireless Motion Detector AA Lithium (GE #60-619) (8-10 year lifespan) 1. Push the button on top of the sensor to detach from mounting plate. side. Pull to remove 3. Remove batteries, and observing correct polarity, replace. 60-511-02-95 Wireless Motion 3.6VDC Lithium 1. Remove cover by gently inserting screwdriver into notch at bottom of 2. Remove the mounting base locking screw on green board. 3. Remove ½ circle lens assembly and green board by gently pulling on the side to release clips. 4. Remove battery, and observing correct polarity, replace. 5. Re-assemble motion and replace mounting screw. 6. Snap cover onto the device. GE Wireless Battery List Page 3 of 5
60-700-95R Crystal Wireless Two AA (GE #60-600) (4-6 year lifespan) 1. Push the bottom on top of the sensor to detach from the mounting plate. side. Pull to remove 3. Remove batteries, and observing polarity, replace. 60-873-95 Crystal Glass Break Two LD123A (GE #60-733) 1. Remove 60-744 Water (4-5 year lifespan) 1. Remove cover by pressing round button on the end of transmitter. 60-412 Freeze (4-5 year lifespan) 1. Remove cover by pressing round button on the end of transmitter. 60-671-95R Wireless Keypad (Simon Panels) (1-year lifespan) 1. Remove battery cover on the back of handheld keypad by sliding cover up. 3. To replace battery cover, align the two exposed tabs with the keypad s front and back cover seam. 4. Press down on battery cover and slide into place. 60-597-95 Wireless Keypad (Concord Panels) #DL123A) (GE #60-733) 1. Remove battery cover on back of handheld keypad by sliding cover up. 3. To replace battery cover, align the two exposed tabs with the keypad s front and back cover seam. 4. Press down on battery cover and slide into place. GE Wireless Battery List Page 4 of 5
60-578 Panic Button 3.6 ½ AA Lithium 1. Remove two screws on back of sensor and separate the front and back plastic. 2. Remove battery, and observing correct polarity, replace. 3. Reassemble the sensor. (To ensure water resistance, be careful not to damage rubber gasket lining.) 60-458 60-457 Panic Button 3.6 ½ AA Lithium (8-10 year lifespan) 60-906-95 Panic Button (Pendant or Wrist Watch) Duracell DL2032 or Panasonic CR2032 1. Remove the 4 screws on the back of the button to separate the cover and base. (You may need to rock the cover to release the tight O-ring seals). 2. Remove battery, and observing correct polarity, replace. 3. Reassemble the button; make sure to align the cover s LED indicator with the boards LED. Simon Panel Control Panel 6V 1.2AH (GE #60-914) 1. Depress the 2 small tabs on top of the console to open. 2. While letting the face hang down, slightly pull apart the tabs holding the battery in place. 3. Remove battery, and observing correct polarity, replace. 4. Replace Concord 4 Control Panel 12V 5AH 1. Open cabinet. 2. Remove black and red wire leads from the existing battery. 3. Observing correct polarity (red and black square on the battery) connect wire leads to the new battery. 4. Secure cabinet. Average Lifespan of Batteries: Panel Battery for XT: Panel Battery for Concord 4: Device using Lithium Batteries: Device using Batteries: 2-4 years 3-5 years 2-4 years unless otherwise stated above 1-2 years unless otherwise stated above Life of a panel battery varies depending upon quality and length of power outages. Life of device batteries varies depending upon location (high-use areas) and number of alarms. All types of alarm batteries are in stock at Keyhole Security. GE Wireless Battery List Page 5 of 5