SELET VEILE PRINT PES NEEE 1 2 3 OW TO USE TIS INSTLL UIE Open the ookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle. Print only the pages for your vehicle using the advanced options in the Print menu. Install your Maestro RR according to the guide for your vehicle. WRNIN Pressing the printer icon or quick printing this document will print all of the guides in this compilation. NOTIE: utomotive ata Solutions Inc. (S) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
INSTLL UIE hevrolet olorado 2015 retains steering wheel controls, Onstar, and more! PROUTS REQUIRE iatalink Maestro RR Radio Replacement Interface iatalink Maestro M3 Installation arness OPTIONL ESSORIES None PRORMME IRMWRE S-RR(SR)-MS03-S NOTIE: utomotive ata Solutions Inc. (S) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
hevrolet olorado 2015 WELOME ongratulations on the purchase of your iatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. efore starting your installation, please ensure that your iatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. TbLE O ONTENTS Installation Instructions 3 Wiring iagram without an mplifier 4 Wiring iagram with an mplifier 5 Radio Wire Reference hart 6 Vehicle Wire Reference hart 7 Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. NEE help? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum maestro.idatalink.com 2
hevrolet olorado 2015 INSTLLTION INSTRUTIONS beore INSTLLIN etermine if the vehicle has a ose amplifier. Look for badges on the radio, door panels, and dash that indicate that the vehicle has ose. If the vehicle OES NOT have a factory amplifier: complete the installation as shown in the wiring diagram without an amplifier. If the vehicle OES have a factory amplifier: complete the installation as shown in the wiring diagram with an amplifier. The amplifier cannot be retained; it must be bypassed or replaced with an aftermarket amplifier. See the vehicle reference chart for wire colors; bypass instructions are not included. Remove the factory radio. STEP 1 Unbox the aftermarket radio and locate its main harness. Refer to the wiring diagram and connect the wires from aftermarket radio main harness to the M3 T-harness and match the wire functions. STEP 2 If the vehicle is equipped with an OEM backup camera, connect the backup camera harness to the uman Machine Interface module harness, located at the bottom of the radio cavity. Note: The guide lines of the backup camera will not be retained. STEP 3 onnect the factory harness to the M3 T-harness. STEP 4 Plug the climate control portion of the M3 T-harness into the climate controls. Plug the OII connector into the OII of the vehicle. STEP 6 If the vehicle OES have steering wheel controls: Remove steering column shroud. Locate the steering wheel control wire in them3 steering wheel harness. ut the REEN/LK wire and splice it into pin 9. Plug the steering wheel control T-harness into the harness at the steering wheel (steering wheel connector located at top of steering column). STEP 7 Plug the aftermarket radio harnesses into the aftermarket radio. onnect the backup camera R cable harness into the aftermarket radio. Plug the ata cable to the data port of the aftermarket radio. Insert the udio cable into the iatalink 3.5 mm audio jack of the aftermarket radio. STEP 8 onnect all the harnesses to the Maestro RR module then proceed test your installation. TROULESOOTIN TIPS: To reset the module back its factory settings, turn the key to the O position then disconnect all connectors from the module. Press and hold the module s programming button and connect all the connectors back to the module. Wait, the module s LE will flash RE rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LE will turn solid REEN for 2 seconds. or technical assistance call 1-866-427-2999 or e-mail support@idatalink.com. Visit us at maestro.idatalink. com/support and www.12voltdata.com/forum/ STEP 5 Plug the male LK 3 pin connector of your M3 T-harness into the OII/SW control harness. 2 maestro.idatalink.com 3
hevrolet olorado 2015 WIRIN IRM without an mplifier STEP 1 STEP 7 WITE - L SPEKER (+) WITE/LK - L SPEKER (-) RY - R SPEKER (+) RY/LK - R SPEKER (-) REEN - LR SPEKER (+) REEN/LK - LR SPEKER (-) PURPLE - RR SPEKER (+) PURPLE/LK - RR SPEKER (-) LUE/WITE - MP. TURN ON (+) LK - ROUN RE - ESSORY (+) YELLOW - 12V (+) ORNE - ILLUMINTION (+) PURPLE/WITE - REVERSE LIT (+) LTREEN - E-RKE (-) PINK - VEILE SPEE YELLOW/LK - OOT RKE SEE RIO WIRE REERENE RT OR RIO WIRE OLORS MIN RNESS R LES ONNET TO TERMRKET RIO KUP M STEP 2 UMN MINE INTERE MOULE RNESS OTTOM O RIO VITY J2 J5 J4 J3 J1 STEP 3 TORY RIO RNESS WIRES ROM VEILE T LE UIO LE STEP 4 LIMTE ONTROLS RNESS STEP 8 SPEKER STEP 5 OII ONNETOR STEP 6 STEERIN WEEL RNESS MESTRO RR MOULE PIN 9 UT REEN/LK WIRE N SPLIE IT TO PIN 9 WIRE M3 T-RNESS 2 maestro.idatalink.com 4
hevrolet olorado 2015 WIRIN IRM with an mplifier STEP 1 STEP 7 WITE - L SPEKER (+) WITE/LK - L SPEKER (-) RY - R SPEKER (+) RY/LK - R SPEKER (-) REEN - LR SPEKER (+) REEN/LK - LR SPEKER (-) PURPLE - RR SPEKER (+) PURPLE/LK - RR SPEKER (-) LUE/WITE - MP. TURN ON (+) LK - ROUN RE - ESSORY (+) YELLOW - 12V (+) ORNE - ILLUMINTION (+) PURPLE/WITE - REVERSE LIT (+) LTREEN - E-RKE (-) PINK - VEILE SPEE YELLOW/LK - OOT RKE O NOT ONNET IN VEILE EQUIPPE WIT TORY MP. SEE MPLIIER YPSS INORMTION IN VEILE WIRE RT. SEE RIO WIRE REERENE RT OR RIO WIRE OLORS MIN RNESS R LES ONNET TO TERMRKET RIO KUP M STEP 2 UMN MINE INTERE MOULE RNESS OTTOM O RIO VITY J2 J5 J4 J3 J1 STEP 3 TORY RIO RNESS WIRES ROM VEILE T LE UIO LE STEP 4 LIMTE ONTROLS RNESS STEP 8 SPEKER STEP 5 OII ONNETOR STEP 6 STEERIN WEEL RNESS MESTRO RR MOULE PIN 9 UT REEN/LK WIRE N SPLIE IT TO PIN 9 WIRE M3 T-RNESS 2 maestro.idatalink.com 5
hevrolet olorado 2015 RIO WIRE REERENE RT Wire escription Polarity Wire olor on Maestro T-arness Wire olor on lpine cable Wire olor on Kenwood cable Wire olor on Pioneer cable Illumination (+) Orange N/ Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-rake (-) Lt reen Yellow/lue Lt reen Lt reen oot rake (+) Yellow/lack Yellow/lack N/ N/ VSS (vehicle speed sensor) (T) Pink reen/white N/ Pink maestro.idatalink.com 6
hevrolet olorado 2015 VEILE WIRE REERENE RT Wire escription onnector Name onnector olor onnector Type Position Wire olor Polarity Wire Location Subwoofer ~ ~ 8 pin 01 klue/ray (+) mplifier, in dashboard, to the right of the glove box Subwoofer ~ ~ 8 pin 05 ray/lack (-) mplifier, in dashboard, to the right of the glove box R Speaker ~ ~ 8 pin 02 Yellow (+) mplifier, in dashboard, to the right of the glove box R Speaker ~ ~ 8 pin 06 Yellow/lack (-) mplifier, in dashboard, to the right of the glove box L Speaker ~ ~ 8 pin 03 klue (+) mplifier, in dashboard, to the right of the glove box L Speaker ~ ~ 8 pin 07 rown/klue (-) mplifier, in dashboard, to the right of the glove box R Tweeter (if R Tweeter (if L Tweeter (if L Tweeter (if ~ ~ 16 pin 04 rown/ltreen (+) mplifier, in dashboard, to the right of the glove box ~ ~ 16 pin 12 Purple/rown (-) mplifier, in dashboard, to the right of the glove box ~ ~ 16 pin 05 Yellow/klue (+) mplifier, in dashboard, to the right of the glove box ~ ~ 16 pin 13 Yellow/ray (-) mplifier, in dashboard, to the right of the glove box RR Speaker ~ ~ 16 pin 06 White (+) mplifier, in dashboard, to the right of the glove box RR Speaker ~ ~ 16 pin 14 klue/lack (-) mplifier, in dashboard, to the right of the glove box LR Speaker ~ ~ 16 pin 07 Ltreen (+) mplifier, in dashboard, to the right of the glove box LR Speaker ~ ~ 16 pin 15 Ltreen/lack (-) mplifier, in dashboard, to the right of the glove box MPLIIER ONNETORS (WIRE SIE) 4 8 3 7 2 6 1 5 8 7 6 5 4 16 15 14 13 12 11 3 2 1 10 9 maestro.idatalink.com 7
INSTLL UIE hevrolet Silverado 1500 2014-2015 retains steering wheel controls, Onstar, and more! PROUTS REQUIRE iatalink Maestro RR Radio Replacement Interface iatalink Maestro M3 Installation arness OPTIONL ESSORIES None PRORMME IRMWRE S-RR(SR)-MS03-S NOTIE: utomotive ata Solutions Inc. (S) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
hevrolet Silverado 1500 2014-2015 WELOME ongratulations on the purchase of your iatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. efore starting your installation, please ensure that your iatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. TbLE O ONTENTS Installation Instructions 3 Wiring iagram without an mplifier 4 Wiring iagram with an mplifier 5 Radio Wire Reference hart 6 Vehicle Wire Reference hart 7 Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. NEE help? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum maestro.idatalink.com 2
hevrolet Silverado 1500 2014-2015 INSTLLTION INSTRUTIONS beore INSTLLIN etermine if the vehicle has a ose amplifier. Look for badges on the radio, door panels, and dash that indicate that the vehicle has ose. If the vehicle OES NOT have a factory amplifier: complete the installation as shown in the wiring diagram without an amplifier. If the vehicle OES have a factory amplifier: complete the installation as shown in the wiring diagram with an amplifier. The amplifier cannot be retained; it must be bypassed or replaced with an aftermarket amplifier. See the vehicle reference chart for wire colors; bypass instructions are not included. Remove the factory radio. STEP 1 Unbox the aftermarket radio and locate its main harness. Refer to the wiring diagram and connect the wires from aftermarket radio main harness to the M3 T-harness and match the wire functions. STEP 2 If the vehicle is equipped with an OEM backup camera, connect the backup camera harness to the uman Machine Interface module harness, located behind the glove box. Note: The guide lines of the backup camera will not be retained. STEP 3 onnect the factory harness to the M3 T-harness. Plug the OII connector into the OII of the vehicle. STEP 6 Remove steering column shroud. Plug the steering wheel control T-harness into the harness at the steering wheel (steering wheel connector located at bottom of steering column). STEP 7 Plug the aftermarket radio harnesses into the aftermarket radio. onnect the backup camera R cable harness into the aftermarket radio. Plug the ata cable to the data port of the aftermarket radio. Insert the udio cable into the iatalink 3.5 mm audio jack of the aftermarket radio. STEP 8 onnect all the harnesses to the Maestro RR module then proceed test your installation. TROULESOOTIN TIPS: To reset the module back its factory settings, turn the key to the O position then disconnect all connectors from the module. Press and hold the module s programming button and connect all the connectors back to the module. Wait, the module s LE will flash RE rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LE will turn solid REEN for 2 seconds. or technical assistance call 1-866-427-2999 or e-mail support@idatalink.com. Visit us at maestro.idatalink. com/support and www.12voltdata.com/forum/ STEP 4 Plug the climate control portion of the M3 T-harness into the climate controls. STEP 5 Plug the male LK 3 pin connector of your M3 T-harness into the OII/SW control harness. 1 maestro.idatalink.com 3
hevrolet Silverado 1500 2014-2015 WIRIN IRM without an mplifier STEP 1 STEP 7 WITE - L SPEKER (+) WITE/LK - L SPEKER (-) RY - R SPEKER (+) RY/LK - R SPEKER (-) REEN - LR SPEKER (+) REEN/LK - LR SPEKER (-) PURPLE - RR SPEKER (+) PURPLE/LK - RR SPEKER (-) LUE/WITE - MP. TURN ON (+) LK - ROUN RE - ESSORY (+) YELLOW - 12V (+) ORNE - ILLUMINTION (+) PURPLE/WITE - REVERSE LIT (+) LTREEN - E-RKE (-) PINK - VEILE SPEE YELLOW/LK - OOT RKE SEE RIO WIRE REERENE RT OR RIO WIRE OLORS MIN RNESS R LES ONNET TO TERMRKET RIO KUP M STEP 2 UMN MINE INTERE MOULE RNESS EIN LOVE OX J2 J5 J4 J3 J1 STEP 3 TORY RIO RNESS WIRES ROM VEILE T LE UIO LE STEP 4 LIMTE ONTROLS RNESS STEP 8 SPEKER STEP 5 OII ONNETOR STEP 6 STEERIN WEEL RNESS MESTRO RR MOULE M3 T-RNESS 1 maestro.idatalink.com 4
hevrolet Silverado 1500 2014-2015 WIRIN IRM with an mplifier STEP 1 STEP 7 WITE - L SPEKER (+) WITE/LK - L SPEKER (-) RY - R SPEKER (+) RY/LK - R SPEKER (-) REEN - LR SPEKER (+) REEN/LK - LR SPEKER (-) PURPLE - RR SPEKER (+) PURPLE/LK - RR SPEKER (-) LUE/WITE - MP. TURN ON (+) LK - ROUN RE - ESSORY (+) YELLOW - 12V (+) ORNE - ILLUMINTION (+) PURPLE/WITE - REVERSE LIT (+) LTREEN - E-RKE (-) PINK - VEILE SPEE YELLOW/LK - OOT RKE O NOT ONNET IN VEILE EQUIPPE WIT TORY MP. SEE MPLIIER YPSS INORMTION IN VEILE WIRE RT. SEE RIO WIRE REERENE RT OR RIO WIRE OLORS MIN RNESS R LES ONNET TO TERMRKET RIO KUP M STEP 2 UMN MINE INTERE MOULE RNESS EIN LOVE OX J2 J5 J4 J3 J1 STEP 3 TORY RIO RNESS WIRES ROM VEILE T LE UIO LE STEP 4 LIMTE ONTROLS RNESS STEP 8 SPEKER STEP 5 OII ONNETOR STEP 6 STEERIN WEEL RNESS MESTRO RR MOULE M3 T-RNESS 1 maestro.idatalink.com 5
hevrolet Silverado 1500 2014-2015 RIO WIRE REERENE RT Wire escription Polarity Wire olor on Maestro T-arness Wire olor on lpine cable Wire olor on Kenwood cable Wire olor on Pioneer cable Illumination (+) Orange N/ Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-rake (-) Lt reen Yellow/lue Lt reen Lt reen oot rake (+) Yellow/lack Yellow/lack N/ N/ VSS (vehicle speed sensor) (T) Pink reen/white N/ Pink maestro.idatalink.com 6
hevrolet Silverado 1500 2014-2015 VEILE WIRE REERENE RT Wire escription onnector Name onnector olor onnector Type Position Wire olor Polarity Wire Location Subwoofer ~ ~ 8 pin 01 klue/ray (+) mplifier, back wall of the cab, center of the wall Subwoofer ~ ~ 8 pin 05 ray/lack (-) mplifier, back wall of the cab, center of the wall R Speaker ~ ~ 8 pin 02 Yellow (+) mplifier, back wall of the cab, center of the wall R Speaker ~ ~ 8 pin 06 Yellow/lack (-) mplifier, back wall of the cab, center of the wall L Speaker ~ ~ 8 pin 03 klue (+) mplifier, back wall of the cab, center of the wall L Speaker ~ ~ 8 pin 07 rown/klue (-) mplifier, back wall of the cab, center of the wall R Tweeter (if R Tweeter (if L Tweeter (if L Tweeter (if ~ ~ 16 pin 04 rown/ltreen (+) mplifier, back wall of the cab, center of the wall ~ ~ 16 pin 12 Purple/rown (-) mplifier, back wall of the cab, center of the wall ~ ~ 16 pin 05 Yellow/klue (+) mplifier, back wall of the cab, center of the wall ~ ~ 16 pin 13 Yellow/ray (-) mplifier, back wall of the cab, center of the wall RR Speaker ~ ~ 16 pin 06 White (+) mplifier, back wall of the cab, center of the wall RR Speaker ~ ~ 16 pin 14 klue/lack (-) mplifier, back wall of the cab, center of the wall LR Speaker ~ ~ 16 pin 07 Ltreen (+) mplifier, back wall of the cab, center of the wall LR Speaker ~ ~ 16 pin 15 Ltreen/lack (-) mplifier, back wall of the cab, center of the wall MPLIIER ONNETORS (WIRE SIE) 4 8 3 7 2 6 1 5 8 7 6 5 4 16 15 14 13 12 11 3 2 1 10 9 maestro.idatalink.com 7
INSTLL UIE hevrolet Silverado 2500 & 3500 2015 PROUTS REQUIRE iatalink Maestro RR Radio Replacement Interface iatalink Maestro M3 Installation arness OPTIONL ESSORIES None PRORMME IRMWRE S-RR(SR)-MS03-S NOTIE: utomotive ata Solutions Inc. (S) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
hevrolet Silverado 2500 & 3500 2015 WELOME ongratulations on the purchase of your iatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. efore starting your installation, please ensure that your iatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. TbLE O ONTENTS Installation Instructions 3 Wiring iagram without an mplifier 4 Wiring iagram with an mplifier 5 Radio Wire Reference hart 6 Vehicle Wire Reference hart 7 Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. NEE help? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum maestro.idatalink.com 2
hevrolet Silverado 2500 & 3500 2015 INSTLLTION INSTRUTIONS beore INSTLLIN etermine if the vehicle has a ose amplifier. Look for badges on the radio, door panels, and dash that indicate that the vehicle has ose. If the vehicle OES NOT have a factory amplifier: complete the installation as shown in the wiring diagram without an amplifier. If the vehicle OES have a factory amplifier: complete the installation as shown in the wiring diagram with an amplifier. The amplifier cannot be retained; it must be bypassed or replaced with an aftermarket amplifier. See the vehicle reference chart for wire colors; bypass instructions are not included. Remove the factory radio. STEP 1 Unbox the aftermarket radio and locate its main harness. Refer to the wiring diagram and connect the wires from aftermarket radio main harness to the M3 T-harness and match the wire functions. STEP 2 If the vehicle is equipped with an OEM backup camera, connect the backup camera harness to the uman Machine Interface module harness, located behind the glove box. Note: The guide lines of the backup camera will not be retained. STEP 3 onnect the factory harness to the M3 T-harness. Plug the OII connector into the OII of the vehicle. STEP 6 Remove steering column shroud. Plug the steering wheel control T-harness into the harness at the steering wheel (steering wheel connector located at bottom of steering column). STEP 7 Plug the aftermarket radio harnesses into the aftermarket radio. onnect the backup camera R cable harness into the aftermarket radio. Plug the ata cable to the data port of the aftermarket radio. Insert the udio cable into the iatalink 3.5 mm audio jack of the aftermarket radio. STEP 8 onnect all the harnesses to the Maestro RR module then proceed test your installation. TROULESOOTIN TIPS: To reset the module back its factory settings, turn the key to the O position then disconnect all connectors from the module. Press and hold the module s programming button and connect all the connectors back to the module. Wait, the module s LE will flash RE rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LE will turn solid REEN for 2 seconds. or technical assistance call 1-866-427-2999 or e-mail support@idatalink.com. Visit us at maestro.idatalink. com/support and www.12voltdata.com/forum/ STEP 4 Plug the climate control portion of the M3 T-harness into the climate controls. STEP 5 Plug the male LK 3 pin connector of your M3 T-harness into the OII/SW control harness. 1 maestro.idatalink.com 3
hevrolet Silverado 2500 & 3500 2015 WIRIN IRM without an mplifier STEP 1 STEP 7 WITE - L SPEKER (+) WITE/LK - L SPEKER (-) RY - R SPEKER (+) RY/LK - R SPEKER (-) REEN - LR SPEKER (+) REEN/LK - LR SPEKER (-) PURPLE - RR SPEKER (+) PURPLE/LK - RR SPEKER (-) LUE/WITE - MP. TURN ON (+) LK - ROUN RE - ESSORY (+) YELLOW - 12V (+) ORNE - ILLUMINTION (+) PURPLE/WITE - REVERSE LIT (+) LTREEN - E-RKE (-) PINK - VEILE SPEE YELLOW/LK - OOT RKE SEE RIO WIRE REERENE RT OR RIO WIRE OLORS MIN RNESS R LES ONNET TO TERMRKET RIO KUP M STEP 2 UMN MINE INTERE MOULE RNESS EIN LOVE OX J2 J5 J4 J3 J1 STEP 3 TORY RIO RNESS WIRES ROM VEILE T LE UIO LE STEP 4 LIMTE ONTROLS RNESS STEP 8 SPEKER STEP 5 OII ONNETOR STEP 6 STEERIN WEEL RNESS MESTRO RR MOULE M3 T-RNESS 1 maestro.idatalink.com 4
hevrolet Silverado 2500 & 3500 2015 WIRIN IRM with an mplifier STEP 1 STEP 7 WITE - L SPEKER (+) WITE/LK - L SPEKER (-) RY - R SPEKER (+) RY/LK - R SPEKER (-) REEN - LR SPEKER (+) REEN/LK - LR SPEKER (-) PURPLE - RR SPEKER (+) PURPLE/LK - RR SPEKER (-) LUE/WITE - MP. TURN ON (+) LK - ROUN RE - ESSORY (+) YELLOW - 12V (+) ORNE - ILLUMINTION (+) PURPLE/WITE - REVERSE LIT (+) LTREEN - E-RKE (-) PINK - VEILE SPEE YELLOW/LK - OOT RKE O NOT ONNET IN VEILE EQUIPPE WIT TORY MP. SEE MPLIIER YPSS INORMTION IN VEILE WIRE RT. SEE RIO WIRE REERENE RT OR RIO WIRE OLORS MIN RNESS R LES ONNET TO TERMRKET RIO KUP M STEP 2 UMN MINE INTERE MOULE RNESS EIN LOVE OX J2 J5 J4 J3 J1 STEP 3 TORY RIO RNESS WIRES ROM VEILE T LE UIO LE STEP 4 LIMTE ONTROLS RNESS STEP 8 SPEKER STEP 5 OII ONNETOR STEP 6 STEERIN WEEL RNESS MESTRO RR MOULE M3 T-RNESS 1 maestro.idatalink.com 5
hevrolet Silverado 2500 & 3500 2015 RIO WIRE REERENE RT Wire escription Polarity Wire olor on Maestro T-arness Wire olor on lpine cable Wire olor on Kenwood cable Wire olor on Pioneer cable Illumination (+) Orange N/ Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-rake (-) Lt reen Yellow/lue Lt reen Lt reen oot rake (+) Yellow/lack Yellow/lack N/ N/ VSS (vehicle speed sensor) (T) Pink reen/white N/ Pink maestro.idatalink.com 6
hevrolet Silverado 2500 & 3500 2015 VEILE WIRE REERENE RT Wire escription onnector Name onnector olor onnector Type Position Wire olor Polarity Wire Location Subwoofer ~ ~ 8 pin 01 klue/ray (+) mplifier, back wall of the cab, center of the wall Subwoofer ~ ~ 8 pin 05 ray/lack (-) mplifier, back wall of the cab, center of the wall R Speaker ~ ~ 8 pin 02 Yellow (+) mplifier, back wall of the cab, center of the wall R Speaker ~ ~ 8 pin 06 Yellow/lack (-) mplifier, back wall of the cab, center of the wall L Speaker ~ ~ 8 pin 03 klue (+) mplifier, back wall of the cab, center of the wall L Speaker ~ ~ 8 pin 07 rown/klue (-) mplifier, back wall of the cab, center of the wall R Tweeter (if R Tweeter (if L Tweeter (if L Tweeter (if ~ ~ 16 pin 04 rown/ltreen (+) mplifier, back wall of the cab, center of the wall ~ ~ 16 pin 12 Purple/rown (-) mplifier, back wall of the cab, center of the wall ~ ~ 16 pin 05 Yellow/klue (+) mplifier, back wall of the cab, center of the wall ~ ~ 16 pin 13 Yellow/ray (-) mplifier, back wall of the cab, center of the wall RR Speaker ~ ~ 16 pin 06 White (+) mplifier, back wall of the cab, center of the wall RR Speaker ~ ~ 16 pin 14 klue/lack (-) mplifier, back wall of the cab, center of the wall LR Speaker ~ ~ 16 pin 07 Ltreen (+) mplifier, back wall of the cab, center of the wall LR Speaker ~ ~ 16 pin 15 Ltreen/lack (-) mplifier, back wall of the cab, center of the wall MPLIIER ONNETORS (WIRE SIE) 4 8 3 7 2 6 1 5 8 7 6 5 4 16 15 14 13 12 11 3 2 1 10 9 maestro.idatalink.com 7
INSTLL UIE hevrolet Suburban 2015 retains steering wheel controls, Onstar, and more! PROUTS REQUIRE iatalink Maestro RR Radio Replacement Interface iatalink Maestro M3 Installation arness OPTIONL ESSORIES None PRORMME IRMWRE S-RR(SR)-MS03-S NOTIE: utomotive ata Solutions Inc. (S) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
hevrolet Suburban 2015 WELOME ongratulations on the purchase of your iatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. efore starting your installation, please ensure that your iatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. TbLE O ONTENTS Installation Instructions 3 Wiring iagram without an mplifier 4 Wiring iagram with an mplifier 5 Radio Wire Reference hart 6 Vehicle Wire Reference hart 7 Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. NEE help? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum maestro.idatalink.com 2
hevrolet Suburban 2015 INSTLLTION INSTRUTIONS beore INSTLLIN etermine if the vehicle has a ose amplifier. Look for badges on the radio, door panels, and dash that indicate that the vehicle has ose. If the vehicle OES NOT have a factory amplifier: complete the installation as shown in the wiring diagram without an amplifier. If the vehicle OES have a factory amplifier: complete the installation as shown in the wiring diagram with an amplifier. The amplifier cannot be retained; it must be bypassed or replaced with an aftermarket amplifier. See the vehicle reference chart for wire colors; bypass instructions are not included. Remove the factory radio. STEP 1 Unbox the aftermarket radio and locate its main harness. Refer to the wiring diagram and connect the wires from aftermarket radio main harness to the M3 T-harness and match the wire functions. STEP 2 If the vehicle is equipped with an OEM backup camera, connect the backup camera harness to the uman Machine Interface module harness, located behind the glove box. Note: The guide lines of the backup camera will not be retained. STEP 3 onnect the factory harness to the M3 T-harness. Plug the OII connector into the OII of the vehicle. STEP 6 Remove steering column shroud. Plug the steering wheel control T-harness into the harness at the steering wheel (steering wheel connector located at bottom of steering column). STEP 7 Plug the aftermarket radio harnesses into the aftermarket radio. onnect the backup camera R cable harness into the aftermarket radio. Plug the ata cable to the data port of the aftermarket radio. Insert the udio cable into the iatalink 3.5 mm audio jack of the aftermarket radio. STEP 8 onnect all the harnesses to the Maestro RR module then proceed test your installation. TROULESOOTIN TIPS: To reset the module back its factory settings, turn the key to the O position then disconnect all connectors from the module. Press and hold the module s programming button and connect all the connectors back to the module. Wait, the module s LE will flash RE rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LE will turn solid REEN for 2 seconds. or technical assistance call 1-866-427-2999 or e-mail support@idatalink.com. Visit us at maestro.idatalink. com/support and www.12voltdata.com/forum/ STEP 4 Plug the climate control portion of the M3 T-harness into the climate controls. STEP 5 Plug the male LK 3 pin connector of your M3 T-harness into the OII/SW control harness. 1 maestro.idatalink.com 3
hevrolet Suburban 2015 WIRIN IRM without an mplifier STEP 1 STEP 7 WITE - L SPEKER (+) WITE/LK - L SPEKER (-) RY - R SPEKER (+) RY/LK - R SPEKER (-) REEN - LR SPEKER (+) REEN/LK - LR SPEKER (-) PURPLE - RR SPEKER (+) PURPLE/LK - RR SPEKER (-) LUE/WITE - MP. TURN ON (+) LK - ROUN RE - ESSORY (+) YELLOW - 12V (+) ORNE - ILLUMINTION (+) PURPLE/WITE - REVERSE LIT (+) LTREEN - E-RKE (-) PINK - VEILE SPEE YELLOW/LK - OOT RKE SEE RIO WIRE REERENE RT OR RIO WIRE OLORS MIN RNESS R LES ONNET TO TERMRKET RIO KUP M STEP 2 UMN MINE INTERE MOULE RNESS EIN LOVE OX J2 J5 J4 J3 J1 STEP 3 TORY RIO RNESS WIRES ROM VEILE T LE UIO LE STEP 4 LIMTE ONTROLS RNESS STEP 8 SPEKER STEP 5 OII ONNETOR STEP 6 STEERIN WEEL RNESS MESTRO RR MOULE M3 T-RNESS 1 maestro.idatalink.com 4
hevrolet Suburban 2015 WIRIN IRM with an mplifier STEP 1 STEP 7 WITE - L SPEKER (+) WITE/LK - L SPEKER (-) RY - R SPEKER (+) RY/LK - R SPEKER (-) REEN - LR SPEKER (+) REEN/LK - LR SPEKER (-) PURPLE - RR SPEKER (+) PURPLE/LK - RR SPEKER (-) LUE/WITE - MP. TURN ON (+) LK - ROUN RE - ESSORY (+) YELLOW - 12V (+) ORNE - ILLUMINTION (+) PURPLE/WITE - REVERSE LIT (+) LTREEN - E-RKE (-) PINK - VEILE SPEE YELLOW/LK - OOT RKE O NOT ONNET IN VEILE EQUIPPE WIT TORY MP. SEE MPLIIER YPSS INORMTION IN VEILE WIRE RT. SEE RIO WIRE REERENE RT OR RIO WIRE OLORS MIN RNESS R LES ONNET TO TERMRKET RIO KUP M STEP 2 UMN MINE INTERE MOULE RNESS EIN LOVE OX J2 J5 J4 J3 J1 STEP 3 TORY RIO RNESS WIRES ROM VEILE T LE UIO LE STEP 4 LIMTE ONTROLS RNESS STEP 8 SPEKER STEP 5 OII ONNETOR STEP 6 STEERIN WEEL RNESS MESTRO RR MOULE M3 T-RNESS 1 maestro.idatalink.com 5
hevrolet Suburban 2015 RIO WIRE REERENE RT Wire escription Polarity Wire olor on Maestro T-arness Wire olor on lpine cable Wire olor on Kenwood cable Wire olor on Pioneer cable Illumination (+) Orange N/ Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-rake (-) Lt reen Yellow/lue Lt reen Lt reen oot rake (+) Yellow/lack Yellow/lack N/ N/ VSS (vehicle speed sensor) (T) Pink reen/white N/ Pink maestro.idatalink.com 6
hevrolet Suburban 2015 VEILE WIRE REERENE RT Wire escription onnector Name onnector olor onnector Type Position Wire olor Polarity Wire Location Subwoofer ~ ~ 8 pin 01 klue/ray (+) mplifier, left side of cargo area, behind wheel well Subwoofer ~ ~ 8 pin 05 ray/lack (-) mplifier, left side of cargo area, behind wheel well R Speaker ~ ~ 8 pin 02 Yellow (+) mplifier, left side of cargo area, behind wheel well R Speaker ~ ~ 8 pin 06 Yellow/lack (-) mplifier, left side of cargo area, behind wheel well L Speaker ~ ~ 8 pin 03 klue (+) mplifier, left side of cargo area, behind wheel well L Speaker ~ ~ 8 pin 07 rown/klue (-) mplifier, left side of cargo area, behind wheel well R Tweeter (if R Tweeter (if L Tweeter (if L Tweeter (if ~ ~ 16 pin 04 rown/ltreen (+) mplifier, left side of cargo area, behind wheel well ~ ~ 16 pin 12 Purple/rown (-) mplifier, left side of cargo area, behind wheel well ~ ~ 16 pin 05 Yellow/klue (+) mplifier, left side of cargo area, behind wheel well ~ ~ 16 pin 13 Yellow/ray (-) mplifier, left side of cargo area, behind wheel well RR Speaker ~ ~ 16 pin 06 White (+) mplifier, left side of cargo area, behind wheel well RR Speaker ~ ~ 16 pin 14 klue/lack (-) mplifier, left side of cargo area, behind wheel well LR Speaker ~ ~ 16 pin 07 Ltreen (+) mplifier, left side of cargo area, behind wheel well LR Speaker ~ ~ 16 pin 15 Ltreen/lack (-) mplifier, left side of cargo area, behind wheel well MPLIIER ONNETORS (WIRE SIE) 4 8 3 7 2 6 1 5 8 7 6 5 4 16 15 14 13 12 11 3 2 1 10 9 maestro.idatalink.com 7
INSTLL UIE hevrolet Tahoe 2015 retains steering wheel controls, Onstar, and more! PROUTS REQUIRE iatalink Maestro RR Radio Replacement Interface iatalink Maestro M3 Installation arness OPTIONL ESSORIES None PRORMME IRMWRE S-RR(SR)-MS03-S NOTIE: utomotive ata Solutions Inc. (S) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
hevrolet Tahoe 2015 WELOME ongratulations on the purchase of your iatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. efore starting your installation, please ensure that your iatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. TbLE O ONTENTS Installation Instructions 3 Wiring iagram without an mplifier 4 Wiring iagram with an mplifier 5 Radio Wire Reference hart 6 Vehicle Wire Reference hart 7 Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. NEE help? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum maestro.idatalink.com 2
hevrolet Tahoe 2015 INSTLLTION INSTRUTIONS beore INSTLLIN etermine if the vehicle has a ose amplifier. Look for badges on the radio, door panels, and dash that indicate that the vehicle has ose. If the vehicle OES NOT have a factory amplifier: complete the installation as shown in the wiring diagram without an amplifier. If the vehicle OES have a factory amplifier: complete the installation as shown in the wiring diagram with an amplifier. The amplifier cannot be retained; it must be bypassed or replaced with an aftermarket amplifier. See the vehicle reference chart for wire colors; bypass instructions are not included. Remove the factory radio. STEP 1 Unbox the aftermarket radio and locate its main harness. Refer to the wiring diagram and connect the wires from aftermarket radio main harness to the M3 T-harness and match the wire functions. STEP 2 If the vehicle is equipped with an OEM backup camera, connect the backup camera harness to the uman Machine Interface module harness, located behind the glove box. Note: The guide lines of the backup camera will not be retained. STEP 3 onnect the factory harness to the M3 T-harness. Plug the OII connector into the OII of the vehicle. STEP 6 Remove steering column shroud. Plug the steering wheel control T-harness into the harness at the steering wheel (steering wheel connector located at bottom of steering column). STEP 7 Plug the aftermarket radio harnesses into the aftermarket radio. onnect the backup camera R cable harness into the aftermarket radio. Plug the ata cable to the data port of the aftermarket radio. Insert the udio cable into the iatalink 3.5 mm audio jack of the aftermarket radio. STEP 8 onnect all the harnesses to the Maestro RR module then proceed test your installation. TROULESOOTIN TIPS: To reset the module back its factory settings, turn the key to the O position then disconnect all connectors from the module. Press and hold the module s programming button and connect all the connectors back to the module. Wait, the module s LE will flash RE rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LE will turn solid REEN for 2 seconds. or technical assistance call 1-866-427-2999 or e-mail support@idatalink.com. Visit us at maestro.idatalink. com/support and www.12voltdata.com/forum/ STEP 4 Plug the climate control portion of the M3 T-harness into the climate controls. STEP 5 Plug the male LK 3 pin connector of your M3 T-harness into the OII/SW control harness. 1 maestro.idatalink.com 3
hevrolet Tahoe 2015 WIRIN IRM without an mplifier STEP 1 STEP 7 WITE - L SPEKER (+) WITE/LK - L SPEKER (-) RY - R SPEKER (+) RY/LK - R SPEKER (-) REEN - LR SPEKER (+) REEN/LK - LR SPEKER (-) PURPLE - RR SPEKER (+) PURPLE/LK - RR SPEKER (-) LUE/WITE - MP. TURN ON (+) LK - ROUN RE - ESSORY (+) YELLOW - 12V (+) ORNE - ILLUMINTION (+) PURPLE/WITE - REVERSE LIT (+) LTREEN - E-RKE (-) PINK - VEILE SPEE YELLOW/LK - OOT RKE SEE RIO WIRE REERENE RT OR RIO WIRE OLORS MIN RNESS R LES ONNET TO TERMRKET RIO KUP M STEP 2 UMN MINE INTERE MOULE RNESS EIN LOVE OX J2 J5 J4 J3 J1 STEP 3 TORY RIO RNESS WIRES ROM VEILE T LE UIO LE STEP 4 LIMTE ONTROLS RNESS STEP 8 SPEKER STEP 5 OII ONNETOR STEP 6 STEERIN WEEL RNESS MESTRO RR MOULE M3 T-RNESS 1 maestro.idatalink.com 4
hevrolet Tahoe 2015 WIRIN IRM with an mplifier STEP 1 STEP 7 WITE - L SPEKER (+) WITE/LK - L SPEKER (-) RY - R SPEKER (+) RY/LK - R SPEKER (-) REEN - LR SPEKER (+) REEN/LK - LR SPEKER (-) PURPLE - RR SPEKER (+) PURPLE/LK - RR SPEKER (-) LUE/WITE - MP. TURN ON (+) LK - ROUN RE - ESSORY (+) YELLOW - 12V (+) ORNE - ILLUMINTION (+) PURPLE/WITE - REVERSE LIT (+) LTREEN - E-RKE (-) PINK - VEILE SPEE YELLOW/LK - OOT RKE O NOT ONNET IN VEILE EQUIPPE WIT TORY MP. SEE MPLIIER YPSS INORMTION IN VEILE WIRE RT. SEE RIO WIRE REERENE RT OR RIO WIRE OLORS MIN RNESS R LES ONNET TO TERMRKET RIO KUP M STEP 2 UMN MINE INTERE MOULE RNESS EIN LOVE OX J2 J5 J4 J3 J1 STEP 3 TORY RIO RNESS WIRES ROM VEILE T LE UIO LE STEP 4 LIMTE ONTROLS RNESS STEP 8 SPEKER STEP 5 OII ONNETOR STEP 6 STEERIN WEEL RNESS MESTRO RR MOULE M3 T-RNESS 1 maestro.idatalink.com 5
hevrolet Tahoe 2015 RIO WIRE REERENE RT Wire escription Polarity Wire olor on Maestro T-arness Wire olor on lpine cable Wire olor on Kenwood cable Wire olor on Pioneer cable Illumination (+) Orange N/ Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-rake (-) Lt reen Yellow/lue Lt reen Lt reen oot rake (+) Yellow/lack Yellow/lack N/ N/ VSS (vehicle speed sensor) (T) Pink reen/white N/ Pink maestro.idatalink.com 6
hevrolet Tahoe 2015 VEILE WIRE REERENE RT Wire escription onnector Name onnector olor onnector Type Position Wire olor Polarity Wire Location Subwoofer ~ ~ 8 pin 01 klue/ray (+) mplifier, left side of cargo area, behind wheel well Subwoofer ~ ~ 8 pin 05 ray/lack (-) mplifier, left side of cargo area, behind wheel well R Speaker ~ ~ 8 pin 02 Yellow (+) mplifier, left side of cargo area, behind wheel well R Speaker ~ ~ 8 pin 06 Yellow/lack (-) mplifier, left side of cargo area, behind wheel well L Speaker ~ ~ 8 pin 03 klue (+) mplifier, left side of cargo area, behind wheel well L Speaker ~ ~ 8 pin 07 rown/klue (-) mplifier, left side of cargo area, behind wheel well R Tweeter (if R Tweeter (if L Tweeter (if L Tweeter (if ~ ~ 16 pin 04 rown/ltreen (+) mplifier, left side of cargo area, behind wheel well ~ ~ 16 pin 12 Purple/rown (-) mplifier, left side of cargo area, behind wheel well ~ ~ 16 pin 05 Yellow/klue (+) mplifier, left side of cargo area, behind wheel well ~ ~ 16 pin 13 Yellow/ray (-) mplifier, left side of cargo area, behind wheel well RR Speaker ~ ~ 16 pin 06 White (+) mplifier, left side of cargo area, behind wheel well RR Speaker ~ ~ 16 pin 14 klue/lack (-) mplifier, left side of cargo area, behind wheel well LR Speaker ~ ~ 16 pin 07 Ltreen (+) mplifier, left side of cargo area, behind wheel well LR Speaker ~ ~ 16 pin 15 Ltreen/lack (-) mplifier, left side of cargo area, behind wheel well MPLIIER ONNETORS (WIRE SIE) 4 8 3 7 2 6 1 5 8 7 6 5 4 16 15 14 13 12 11 3 2 1 10 9 maestro.idatalink.com 7
INSTLL UIE M anyon 2015 retains steering wheel controls, Onstar, and more! PROUTS REQUIRE iatalink Maestro RR Radio Replacement Interface iatalink Maestro M3 Installation arness OPTIONL ESSORIES None PRORMME IRMWRE S-RR(SR)-MS03-S NOTIE: utomotive ata Solutions Inc. (S) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
M anyon 2015 WELOME ongratulations on the purchase of your iatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. efore starting your installation, please ensure that your iatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. TbLE O ONTENTS Installation Instructions 3 Wiring iagram without an mplifier 4 Wiring iagram with an mplifier 5 Radio Wire Reference hart 6 Vehicle Wire Reference hart 7 Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. NEE help? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum maestro.idatalink.com 2
M anyon 2015 INSTLLTION INSTRUTIONS beore INSTLLIN etermine if the vehicle has a ose amplifier. Look for badges on the radio, door panels, and dash that indicate that the vehicle has ose. If the vehicle OES NOT have a factory amplifier: complete the installation as shown in the wiring diagram without an amplifier. If the vehicle OES have a factory amplifier: complete the installation as shown in the wiring diagram with an amplifier. The amplifier cannot be retained; it must be bypassed or replaced with an aftermarket amplifier. See the vehicle reference chart for wire colors; bypass instructions are not included. Remove the factory radio. STEP 1 Unbox the aftermarket radio and locate its main harness. Refer to the wiring diagram and connect the wires from aftermarket radio main harness to the M3 T-harness and match the wire functions. STEP 2 If the vehicle is equipped with an OEM backup camera, connect the backup camera harness to the uman Machine Interface module harness, located at the bottom of the radio cavity. Note: The guide lines of the backup camera will not be retained. STEP 3 onnect the factory harness to the M3 T-harness. STEP 4 Plug the climate control portion of the M3 T-harness into the climate controls. Plug the OII connector into the OII of the vehicle. STEP 6 If the vehicle OES have steering wheel controls: Remove steering column shroud. Locate the steering wheel control wire in them3 steering wheel harness. ut the REEN/LK wire and splice it into pin 9. Plug the steering wheel control T-harness into the harness at the steering wheel (steering wheel connector located at top of steering column). STEP 7 Plug the aftermarket radio harnesses into the aftermarket radio. onnect the backup camera R cable harness into the aftermarket radio. Plug the ata cable to the data port of the aftermarket radio. Insert the udio cable into the iatalink 3.5 mm audio jack of the aftermarket radio. STEP 8 onnect all the harnesses to the Maestro RR module then proceed test your installation. TROULESOOTIN TIPS: To reset the module back its factory settings, turn the key to the O position then disconnect all connectors from the module. Press and hold the module s programming button and connect all the connectors back to the module. Wait, the module s LE will flash RE rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LE will turn solid REEN for 2 seconds. or technical assistance call 1-866-427-2999 or e-mail support@idatalink.com. Visit us at maestro.idatalink. com/support and www.12voltdata.com/forum/ STEP 5 Plug the male LK 3 pin connector of your M3 T-harness into the OII/SW control harness. 2 maestro.idatalink.com 3
M anyon 2015 WIRIN IRM without an mplifier STEP 1 STEP 7 WITE - L SPEKER (+) WITE/LK - L SPEKER (-) RY - R SPEKER (+) RY/LK - R SPEKER (-) REEN - LR SPEKER (+) REEN/LK - LR SPEKER (-) PURPLE - RR SPEKER (+) PURPLE/LK - RR SPEKER (-) LUE/WITE - MP. TURN ON (+) LK - ROUN RE - ESSORY (+) YELLOW - 12V (+) ORNE - ILLUMINTION (+) PURPLE/WITE - REVERSE LIT (+) LTREEN - E-RKE (-) PINK - VEILE SPEE YELLOW/LK - OOT RKE SEE RIO WIRE REERENE RT OR RIO WIRE OLORS MIN RNESS R LES ONNET TO TERMRKET RIO KUP M STEP 2 UMN MINE INTERE MOULE RNESS OTTOM O RIO VITY J2 J5 J4 J3 J1 STEP 3 TORY RIO RNESS WIRES ROM VEILE T LE UIO LE STEP 4 LIMTE ONTROLS RNESS STEP 8 SPEKER STEP 5 OII ONNETOR STEP 6 STEERIN WEEL RNESS MESTRO RR MOULE PIN 9 UT REEN/LK WIRE N SPLIE IT TO PIN 9 WIRE M3 T-RNESS 2 maestro.idatalink.com 4
M anyon 2015 WIRIN IRM with an mplifier STEP 1 STEP 7 WITE - L SPEKER (+) WITE/LK - L SPEKER (-) RY - R SPEKER (+) RY/LK - R SPEKER (-) REEN - LR SPEKER (+) REEN/LK - LR SPEKER (-) PURPLE - RR SPEKER (+) PURPLE/LK - RR SPEKER (-) LUE/WITE - MP. TURN ON (+) LK - ROUN RE - ESSORY (+) YELLOW - 12V (+) ORNE - ILLUMINTION (+) PURPLE/WITE - REVERSE LIT (+) LTREEN - E-RKE (-) PINK - VEILE SPEE YELLOW/LK - OOT RKE O NOT ONNET IN VEILE EQUIPPE WIT TORY MP. SEE MPLIIER YPSS INORMTION IN VEILE WIRE RT. SEE RIO WIRE REERENE RT OR RIO WIRE OLORS MIN RNESS R LES ONNET TO TERMRKET RIO KUP M STEP 2 UMN MINE INTERE MOULE RNESS OTTOM O RIO VITY J2 J5 J4 J3 J1 STEP 3 TORY RIO RNESS WIRES ROM VEILE T LE UIO LE STEP 4 LIMTE ONTROLS RNESS STEP 8 SPEKER STEP 5 OII ONNETOR STEP 6 STEERIN WEEL RNESS MESTRO RR MOULE PIN 9 UT REEN/LK WIRE N SPLIE IT TO PIN 9 WIRE M3 T-RNESS 2 maestro.idatalink.com 5
M anyon 2015 RIO WIRE REERENE RT Wire escription Polarity Wire olor on Maestro T-arness Wire olor on lpine cable Wire olor on Kenwood cable Wire olor on Pioneer cable Illumination (+) Orange N/ Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-rake (-) Lt reen Yellow/lue Lt reen Lt reen oot rake (+) Yellow/lack Yellow/lack N/ N/ VSS (vehicle speed sensor) (T) Pink reen/white N/ Pink maestro.idatalink.com 6
M anyon 2015 VEILE WIRE REERENE RT Wire escription onnector Name onnector olor onnector Type Position Wire olor Polarity Wire Location Subwoofer ~ ~ 8 pin 01 klue/ray (+) mplifier, in dashboard, to the right of the glove box Subwoofer ~ ~ 8 pin 05 ray/lack (-) mplifier, in dashboard, to the right of the glove box R Speaker ~ ~ 8 pin 02 Yellow (+) mplifier, in dashboard, to the right of the glove box R Speaker ~ ~ 8 pin 06 Yellow/lack (-) mplifier, in dashboard, to the right of the glove box L Speaker ~ ~ 8 pin 03 klue (+) mplifier, in dashboard, to the right of the glove box L Speaker ~ ~ 8 pin 07 rown/klue (-) mplifier, in dashboard, to the right of the glove box R Tweeter (if R Tweeter (if L Tweeter (if L Tweeter (if ~ ~ 16 pin 04 rown/ltreen (+) mplifier, in dashboard, to the right of the glove box ~ ~ 16 pin 12 Purple/rown (-) mplifier, in dashboard, to the right of the glove box ~ ~ 16 pin 05 Yellow/klue (+) mplifier, in dashboard, to the right of the glove box ~ ~ 16 pin 13 Yellow/ray (-) mplifier, in dashboard, to the right of the glove box RR Speaker ~ ~ 16 pin 06 White (+) mplifier, in dashboard, to the right of the glove box RR Speaker ~ ~ 16 pin 14 klue/lack (-) mplifier, in dashboard, to the right of the glove box LR Speaker ~ ~ 16 pin 07 Ltreen (+) mplifier, in dashboard, to the right of the glove box LR Speaker ~ ~ 16 pin 15 Ltreen/lack (-) mplifier, in dashboard, to the right of the glove box MPLIIER ONNETORS (WIRE SIE) 4 8 3 7 2 6 1 5 8 7 6 5 4 16 15 14 13 12 11 3 2 1 10 9 maestro.idatalink.com 7
INSTLL UIE M Sierra 1500 2014-2015 retains steering wheel controls, Onstar, and more! PROUTS REQUIRE iatalink Maestro RR Radio Replacement Interface iatalink Maestro M3 Installation arness OPTIONL ESSORIES None PRORMME IRMWRE S-RR(SR)-MS03-S NOTIE: utomotive ata Solutions Inc. (S) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
M Sierra 1500 2014-2015 WELOME ongratulations on the purchase of your iatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. efore starting your installation, please ensure that your iatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. TbLE O ONTENTS Installation Instructions 3 Wiring iagram without an mplifier 4 Wiring iagram with an mplifier 5 Radio Wire Reference hart 6 Vehicle Wire Reference hart 7 Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. NEE help? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum maestro.idatalink.com 2
M Sierra 1500 2014-2015 INSTLLTION INSTRUTIONS beore INSTLLIN etermine if the vehicle has a ose amplifier. Look for badges on the radio, door panels, and dash that indicate that the vehicle has ose. If the vehicle OES NOT have a factory amplifier: complete the installation as shown in the wiring diagram without an amplifier. If the vehicle OES have a factory amplifier: complete the installation as shown in the wiring diagram with an amplifier. The amplifier cannot be retained; it must be bypassed or replaced with an aftermarket amplifier. See the vehicle reference chart for wire colors; bypass instructions are not included. Remove the factory radio. STEP 1 Unbox the aftermarket radio and locate its main harness. Refer to the wiring diagram and connect the wires from aftermarket radio main harness to the M3 T-harness and match the wire functions. STEP 2 If the vehicle is equipped with an OEM backup camera, connect the backup camera harness to the uman Machine Interface module harness, located behind the glove box. Note: The guide lines of the backup camera will not be retained. STEP 3 onnect the factory harness to the M3 T-harness. Plug the OII connector into the OII of the vehicle. STEP 6 Remove steering column shroud. Plug the steering wheel control T-harness into the harness at the steering wheel (steering wheel connector located at bottom of steering column). STEP 7 Plug the aftermarket radio harnesses into the aftermarket radio. onnect the backup camera R cable harness into the aftermarket radio. Plug the ata cable to the data port of the aftermarket radio. Insert the udio cable into the iatalink 3.5 mm audio jack of the aftermarket radio. STEP 8 onnect all the harnesses to the Maestro RR module then proceed test your installation. TROULESOOTIN TIPS: To reset the module back its factory settings, turn the key to the O position then disconnect all connectors from the module. Press and hold the module s programming button and connect all the connectors back to the module. Wait, the module s LE will flash RE rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LE will turn solid REEN for 2 seconds. or technical assistance call 1-866-427-2999 or e-mail support@idatalink.com. Visit us at maestro.idatalink. com/support and www.12voltdata.com/forum/ STEP 4 Plug the climate control portion of the M3 T-harness into the climate controls. STEP 5 Plug the male LK 3 pin connector of your M3 T-harness into the OII/SW control harness. 1 maestro.idatalink.com 3
M Sierra 1500 2014-2015 WIRIN IRM without an mplifier STEP 1 STEP 7 WITE - L SPEKER (+) WITE/LK - L SPEKER (-) RY - R SPEKER (+) RY/LK - R SPEKER (-) REEN - LR SPEKER (+) REEN/LK - LR SPEKER (-) PURPLE - RR SPEKER (+) PURPLE/LK - RR SPEKER (-) LUE/WITE - MP. TURN ON (+) LK - ROUN RE - ESSORY (+) YELLOW - 12V (+) ORNE - ILLUMINTION (+) PURPLE/WITE - REVERSE LIT (+) LTREEN - E-RKE (-) PINK - VEILE SPEE YELLOW/LK - OOT RKE SEE RIO WIRE REERENE RT OR RIO WIRE OLORS MIN RNESS R LES ONNET TO TERMRKET RIO KUP M STEP 2 UMN MINE INTERE MOULE RNESS EIN LOVE OX J2 J5 J4 J3 J1 STEP 3 TORY RIO RNESS WIRES ROM VEILE T LE UIO LE STEP 4 LIMTE ONTROLS RNESS STEP 8 SPEKER STEP 5 OII ONNETOR STEP 6 STEERIN WEEL RNESS MESTRO RR MOULE M3 T-RNESS 1 maestro.idatalink.com 4
M Sierra 1500 2014-2015 WIRIN IRM with an mplifier STEP 1 STEP 7 WITE - L SPEKER (+) WITE/LK - L SPEKER (-) RY - R SPEKER (+) RY/LK - R SPEKER (-) REEN - LR SPEKER (+) REEN/LK - LR SPEKER (-) PURPLE - RR SPEKER (+) PURPLE/LK - RR SPEKER (-) LUE/WITE - MP. TURN ON (+) LK - ROUN RE - ESSORY (+) YELLOW - 12V (+) ORNE - ILLUMINTION (+) PURPLE/WITE - REVERSE LIT (+) LTREEN - E-RKE (-) PINK - VEILE SPEE YELLOW/LK - OOT RKE O NOT ONNET IN VEILE EQUIPPE WIT TORY MP. SEE MPLIIER YPSS INORMTION IN VEILE WIRE RT. SEE RIO WIRE REERENE RT OR RIO WIRE OLORS MIN RNESS R LES ONNET TO TERMRKET RIO KUP M STEP 2 UMN MINE INTERE MOULE RNESS EIN LOVE OX J2 J5 J4 J3 J1 STEP 3 TORY RIO RNESS WIRES ROM VEILE T LE UIO LE STEP 4 LIMTE ONTROLS RNESS STEP 8 SPEKER STEP 5 OII ONNETOR STEP 6 STEERIN WEEL RNESS MESTRO RR MOULE M3 T-RNESS 1 maestro.idatalink.com 5
M Sierra 1500 2014-2015 RIO WIRE REERENE RT Wire escription Polarity Wire olor on Maestro T-arness Wire olor on lpine cable Wire olor on Kenwood cable Wire olor on Pioneer cable Illumination (+) Orange N/ Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-rake (-) Lt reen Yellow/lue Lt reen Lt reen oot rake (+) Yellow/lack Yellow/lack N/ N/ VSS (vehicle speed sensor) (T) Pink reen/white N/ Pink maestro.idatalink.com 6
M Sierra 1500 2014-2015 VEILE WIRE REERENE RT Wire escription onnector Name onnector olor onnector Type Position Wire olor Polarity Wire Location Subwoofer ~ ~ 8 pin 01 klue/ray (+) mplifier, back wall of the cab, center of the wall Subwoofer ~ ~ 8 pin 05 ray/lack (-) mplifier, back wall of the cab, center of the wall R Speaker ~ ~ 8 pin 02 Yellow (+) mplifier, back wall of the cab, center of the wall R Speaker ~ ~ 8 pin 06 Yellow/lack (-) mplifier, back wall of the cab, center of the wall L Speaker ~ ~ 8 pin 03 klue (+) mplifier, back wall of the cab, center of the wall L Speaker ~ ~ 8 pin 07 rown/klue (-) mplifier, back wall of the cab, center of the wall R Tweeter (if R Tweeter (if L Tweeter (if L Tweeter (if ~ ~ 16 pin 04 rown/ltreen (+) mplifier, back wall of the cab, center of the wall ~ ~ 16 pin 12 Purple/rown (-) mplifier, back wall of the cab, center of the wall ~ ~ 16 pin 05 Yellow/klue (+) mplifier, back wall of the cab, center of the wall ~ ~ 16 pin 13 Yellow/ray (-) mplifier, back wall of the cab, center of the wall RR Speaker ~ ~ 16 pin 06 White (+) mplifier, back wall of the cab, center of the wall RR Speaker ~ ~ 16 pin 14 klue/lack (-) mplifier, back wall of the cab, center of the wall LR Speaker ~ ~ 16 pin 07 Ltreen (+) mplifier, back wall of the cab, center of the wall LR Speaker ~ ~ 16 pin 15 Ltreen/lack (-) mplifier, back wall of the cab, center of the wall MPLIIER ONNETORS (WIRE SIE) 4 8 3 7 2 6 1 5 8 7 6 5 4 16 15 14 13 12 11 3 2 1 10 9 maestro.idatalink.com 7
INSTLL UIE M Sierra 2500 & 3500 2015 retains steering wheel controls, Onstar, and more! PROUTS REQUIRE iatalink Maestro RR Radio Replacement Interface iatalink Maestro M3 Installation arness OPTIONL ESSORIES None PRORMME IRMWRE S-RR(SR)-MS03-S NOTIE: utomotive ata Solutions Inc. (S) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
M Sierra 2500 & 3500 2015 WELOME ongratulations on the purchase of your iatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. efore starting your installation, please ensure that your iatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. TbLE O ONTENTS Installation Instructions 3 Wiring iagram without an mplifier 4 Wiring iagram with an mplifier 5 Radio Wire Reference hart 6 Vehicle Wire Reference hart 7 Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. NEE help? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum maestro.idatalink.com 2
M Sierra 2500 & 3500 2015 INSTLLTION INSTRUTIONS beore INSTLLIN etermine if the vehicle has a ose amplifier. Look for badges on the radio, door panels, and dash that indicate that the vehicle has ose. If the vehicle OES NOT have a factory amplifier: complete the installation as shown in the wiring diagram without an amplifier. If the vehicle OES have a factory amplifier: complete the installation as shown in the wiring diagram with an amplifier. The amplifier cannot be retained; it must be bypassed or replaced with an aftermarket amplifier. See the vehicle reference chart for wire colors; bypass instructions are not included. Remove the factory radio. STEP 1 Unbox the aftermarket radio and locate its main harness. Refer to the wiring diagram and connect the wires from aftermarket radio main harness to the M3 T-harness and match the wire functions. STEP 2 If the vehicle is equipped with an OEM backup camera, connect the backup camera harness to the uman Machine Interface module harness, located behind the glove box. Note: The guide lines of the backup camera will not be retained. STEP 3 onnect the factory harness to the M3 T-harness. Plug the OII connector into the OII of the vehicle. STEP 6 Remove steering column shroud. Plug the steering wheel control T-harness into the harness at the steering wheel (steering wheel connector located at bottom of steering column). STEP 7 Plug the aftermarket radio harnesses into the aftermarket radio. onnect the backup camera R cable harness into the aftermarket radio. Plug the ata cable to the data port of the aftermarket radio. Insert the udio cable into the iatalink 3.5 mm audio jack of the aftermarket radio. STEP 8 onnect all the harnesses to the Maestro RR module then proceed test your installation. TROULESOOTIN TIPS: To reset the module back its factory settings, turn the key to the O position then disconnect all connectors from the module. Press and hold the module s programming button and connect all the connectors back to the module. Wait, the module s LE will flash RE rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LE will turn solid REEN for 2 seconds. or technical assistance call 1-866-427-2999 or e-mail support@idatalink.com. Visit us at maestro.idatalink. com/support and www.12voltdata.com/forum/ STEP 4 Plug the climate control portion of the M3 T-harness into the climate controls. STEP 5 Plug the male LK 3 pin connector of your M3 T-harness into the OII/SW control harness. 1 maestro.idatalink.com 3
M Sierra 2500 & 3500 2015 WIRIN IRM without an mplifier STEP 1 STEP 7 WITE - L SPEKER (+) WITE/LK - L SPEKER (-) RY - R SPEKER (+) RY/LK - R SPEKER (-) REEN - LR SPEKER (+) REEN/LK - LR SPEKER (-) PURPLE - RR SPEKER (+) PURPLE/LK - RR SPEKER (-) LUE/WITE - MP. TURN ON (+) LK - ROUN RE - ESSORY (+) YELLOW - 12V (+) ORNE - ILLUMINTION (+) PURPLE/WITE - REVERSE LIT (+) LTREEN - E-RKE (-) PINK - VEILE SPEE YELLOW/LK - OOT RKE SEE RIO WIRE REERENE RT OR RIO WIRE OLORS MIN RNESS R LES ONNET TO TERMRKET RIO KUP M STEP 2 UMN MINE INTERE MOULE RNESS EIN LOVE OX J2 J5 J4 J3 J1 STEP 3 TORY RIO RNESS WIRES ROM VEILE T LE UIO LE STEP 4 LIMTE ONTROLS RNESS STEP 8 SPEKER STEP 5 OII ONNETOR STEP 6 STEERIN WEEL RNESS MESTRO RR MOULE M3 T-RNESS 1 maestro.idatalink.com 4
M Sierra 2500 & 3500 2015 WIRIN IRM with an mplifier STEP 1 STEP 7 WITE - L SPEKER (+) WITE/LK - L SPEKER (-) RY - R SPEKER (+) RY/LK - R SPEKER (-) REEN - LR SPEKER (+) REEN/LK - LR SPEKER (-) PURPLE - RR SPEKER (+) PURPLE/LK - RR SPEKER (-) LUE/WITE - MP. TURN ON (+) LK - ROUN RE - ESSORY (+) YELLOW - 12V (+) ORNE - ILLUMINTION (+) PURPLE/WITE - REVERSE LIT (+) LTREEN - E-RKE (-) PINK - VEILE SPEE YELLOW/LK - OOT RKE O NOT ONNET IN VEILE EQUIPPE WIT TORY MP. SEE MPLIIER YPSS INORMTION IN VEILE WIRE RT. SEE RIO WIRE REERENE RT OR RIO WIRE OLORS MIN RNESS R LES ONNET TO TERMRKET RIO KUP M STEP 2 UMN MINE INTERE MOULE RNESS EIN LOVE OX J2 J5 J4 J3 J1 STEP 3 TORY RIO RNESS WIRES ROM VEILE T LE UIO LE STEP 4 LIMTE ONTROLS RNESS STEP 8 SPEKER STEP 5 OII ONNETOR STEP 6 STEERIN WEEL RNESS MESTRO RR MOULE M3 T-RNESS 1 maestro.idatalink.com 5
M Sierra 2500 & 3500 2015 RIO WIRE REERENE RT Wire escription Polarity Wire olor on Maestro T-arness Wire olor on lpine cable Wire olor on Kenwood cable Wire olor on Pioneer cable Illumination (+) Orange N/ Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-rake (-) Lt reen Yellow/lue Lt reen Lt reen oot rake (+) Yellow/lack Yellow/lack N/ N/ VSS (vehicle speed sensor) (T) Pink reen/white N/ Pink maestro.idatalink.com 6
M Sierra 2500 & 3500 2015 VEILE WIRE REERENE RT Wire escription onnector Name onnector olor onnector Type Position Wire olor Polarity Wire Location Subwoofer ~ ~ 8 pin 01 klue/ray (+) mplifier, back wall of the cab, center of the wall Subwoofer ~ ~ 8 pin 05 ray/lack (-) mplifier, back wall of the cab, center of the wall R Speaker ~ ~ 8 pin 02 Yellow (+) mplifier, back wall of the cab, center of the wall R Speaker ~ ~ 8 pin 06 Yellow/lack (-) mplifier, back wall of the cab, center of the wall L Speaker ~ ~ 8 pin 03 klue (+) mplifier, back wall of the cab, center of the wall L Speaker ~ ~ 8 pin 07 rown/klue (-) mplifier, back wall of the cab, center of the wall R Tweeter (if R Tweeter (if L Tweeter (if L Tweeter (if ~ ~ 16 pin 04 rown/ltreen (+) mplifier, back wall of the cab, center of the wall ~ ~ 16 pin 12 Purple/rown (-) mplifier, back wall of the cab, center of the wall ~ ~ 16 pin 05 Yellow/klue (+) mplifier, back wall of the cab, center of the wall ~ ~ 16 pin 13 Yellow/ray (-) mplifier, back wall of the cab, center of the wall RR Speaker ~ ~ 16 pin 06 White (+) mplifier, back wall of the cab, center of the wall RR Speaker ~ ~ 16 pin 14 klue/lack (-) mplifier, back wall of the cab, center of the wall LR Speaker ~ ~ 16 pin 07 Ltreen (+) mplifier, back wall of the cab, center of the wall LR Speaker ~ ~ 16 pin 15 Ltreen/lack (-) mplifier, back wall of the cab, center of the wall MPLIIER ONNETORS (WIRE SIE) 4 8 3 7 2 6 1 5 8 7 6 5 4 16 15 14 13 12 11 3 2 1 10 9 maestro.idatalink.com 7
INSTLL UIE M Yukon & Yukon XL 2015 retains steering wheel controls, Onstar, and more! PROUTS REQUIRE iatalink Maestro RR Radio Replacement Interface iatalink Maestro M3 Installation arness OPTIONL ESSORIES None PRORMME IRMWRE S-RR(SR)-MS03-S NOTIE: utomotive ata Solutions Inc. (S) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
M Yukon & Yukon XL 2015 WELOME ongratulations on the purchase of your iatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. efore starting your installation, please ensure that your iatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. TbLE O ONTENTS Installation Instructions 3 Wiring iagram without an mplifier 4 Wiring iagram with an mplifier 5 Radio Wire Reference hart 6 Vehicle Wire Reference hart 7 Please note that Maestro RR will only retain functionalities that were originally available in the vehicle. NEE help? 1 866 427-2999 support@idatalink.com maestro.idatalink.com/support www.12voltdata.com/forum maestro.idatalink.com 2
M Yukon & Yukon XL 2015 INSTLLTION INSTRUTIONS beore INSTLLIN etermine if the vehicle has a ose amplifier. Look for badges on the radio, door panels, and dash that indicate that the vehicle has ose. If the vehicle OES NOT have a factory amplifier: complete the installation as shown in the wiring diagram without an amplifier. If the vehicle OES have a factory amplifier: complete the installation as shown in the wiring diagram with an amplifier. The amplifier cannot be retained; it must be bypassed or replaced with an aftermarket amplifier. See the vehicle reference chart for wire colors; bypass instructions are not included. Remove the factory radio. STEP 1 Unbox the aftermarket radio and locate its main harness. Refer to the wiring diagram and connect the wires from aftermarket radio main harness to the M3 T-harness and match the wire functions. STEP 2 If the vehicle is equipped with an OEM backup camera, connect the backup camera harness to the uman Machine Interface module harness, located behind the glove box. Note: The guide lines of the backup camera will not be retained. STEP 3 onnect the factory harness to the M3 T-harness. Plug the OII connector into the OII of the vehicle. STEP 6 Remove steering column shroud. Plug the steering wheel control T-harness into the harness at the steering wheel (steering wheel connector located at bottom of steering column). STEP 7 Plug the aftermarket radio harnesses into the aftermarket radio. onnect the backup camera R cable harness into the aftermarket radio. Plug the ata cable to the data port of the aftermarket radio. Insert the udio cable into the iatalink 3.5 mm audio jack of the aftermarket radio. STEP 8 onnect all the harnesses to the Maestro RR module then proceed test your installation. TROULESOOTIN TIPS: To reset the module back its factory settings, turn the key to the O position then disconnect all connectors from the module. Press and hold the module s programming button and connect all the connectors back to the module. Wait, the module s LE will flash RE rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LE will turn solid REEN for 2 seconds. or technical assistance call 1-866-427-2999 or e-mail support@idatalink.com. Visit us at maestro.idatalink. com/support and www.12voltdata.com/forum/ STEP 4 Plug the climate control portion of the M3 T-harness into the climate controls. STEP 5 Plug the male LK 3 pin connector of your M3 T-harness into the OII/SW control harness. 1 maestro.idatalink.com 3
M Yukon & Yukon XL 2015 WIRIN IRM without an mplifier STEP 1 STEP 7 WITE - L SPEKER (+) WITE/LK - L SPEKER (-) RY - R SPEKER (+) RY/LK - R SPEKER (-) REEN - LR SPEKER (+) REEN/LK - LR SPEKER (-) PURPLE - RR SPEKER (+) PURPLE/LK - RR SPEKER (-) LUE/WITE - MP. TURN ON (+) LK - ROUN RE - ESSORY (+) YELLOW - 12V (+) ORNE - ILLUMINTION (+) PURPLE/WITE - REVERSE LIT (+) LTREEN - E-RKE (-) PINK - VEILE SPEE YELLOW/LK - OOT RKE SEE RIO WIRE REERENE RT OR RIO WIRE OLORS MIN RNESS R LES ONNET TO TERMRKET RIO KUP M STEP 2 UMN MINE INTERE MOULE RNESS EIN LOVE OX J2 J5 J4 J3 J1 STEP 3 TORY RIO RNESS WIRES ROM VEILE T LE UIO LE STEP 4 LIMTE ONTROLS RNESS STEP 8 SPEKER STEP 5 OII ONNETOR STEP 6 STEERIN WEEL RNESS MESTRO RR MOULE M3 T-RNESS 1 maestro.idatalink.com 4
M Yukon & Yukon XL 2015 WIRIN IRM with an mplifier STEP 1 STEP 7 WITE - L SPEKER (+) WITE/LK - L SPEKER (-) RY - R SPEKER (+) RY/LK - R SPEKER (-) REEN - LR SPEKER (+) REEN/LK - LR SPEKER (-) PURPLE - RR SPEKER (+) PURPLE/LK - RR SPEKER (-) LUE/WITE - MP. TURN ON (+) LK - ROUN RE - ESSORY (+) YELLOW - 12V (+) ORNE - ILLUMINTION (+) PURPLE/WITE - REVERSE LIT (+) LTREEN - E-RKE (-) PINK - VEILE SPEE YELLOW/LK - OOT RKE O NOT ONNET IN VEILE EQUIPPE WIT TORY MP. SEE MPLIIER YPSS INORMTION IN VEILE WIRE RT. SEE RIO WIRE REERENE RT OR RIO WIRE OLORS MIN RNESS R LES ONNET TO TERMRKET RIO KUP M STEP 2 UMN MINE INTERE MOULE RNESS EIN LOVE OX J2 J5 J4 J3 J1 STEP 3 TORY RIO RNESS WIRES ROM VEILE T LE UIO LE STEP 4 LIMTE ONTROLS RNESS STEP 8 SPEKER STEP 5 OII ONNETOR STEP 6 STEERIN WEEL RNESS MESTRO RR MOULE M3 T-RNESS 1 maestro.idatalink.com 5
M Yukon & Yukon XL 2015 RIO WIRE REERENE RT Wire escription Polarity Wire olor on Maestro T-arness Wire olor on lpine cable Wire olor on Kenwood cable Wire olor on Pioneer cable Illumination (+) Orange N/ Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-rake (-) Lt reen Yellow/lue Lt reen Lt reen oot rake (+) Yellow/lack Yellow/lack N/ N/ VSS (vehicle speed sensor) (T) Pink reen/white N/ Pink maestro.idatalink.com 6
M Yukon & Yukon XL 2015 VEILE WIRE REERENE RT Wire escription onnector Name onnector olor onnector Type Position Wire olor Polarity Wire Location Subwoofer ~ ~ 8 pin 01 klue/ray (+) mplifier, left side of cargo area, behind wheel well Subwoofer ~ ~ 8 pin 05 ray/lack (-) mplifier, left side of cargo area, behind wheel well R Speaker ~ ~ 8 pin 02 Yellow (+) mplifier, left side of cargo area, behind wheel well R Speaker ~ ~ 8 pin 06 Yellow/lack (-) mplifier, left side of cargo area, behind wheel well L Speaker ~ ~ 8 pin 03 klue (+) mplifier, left side of cargo area, behind wheel well L Speaker ~ ~ 8 pin 07 rown/klue (-) mplifier, left side of cargo area, behind wheel well R Tweeter (if R Tweeter (if L Tweeter (if L Tweeter (if ~ ~ 16 pin 04 rown/ltreen (+) mplifier, left side of cargo area, behind wheel well ~ ~ 16 pin 12 Purple/rown (-) mplifier, left side of cargo area, behind wheel well ~ ~ 16 pin 05 Yellow/klue (+) mplifier, left side of cargo area, behind wheel well ~ ~ 16 pin 13 Yellow/ray (-) mplifier, left side of cargo area, behind wheel well RR Speaker ~ ~ 16 pin 06 White (+) mplifier, left side of cargo area, behind wheel well RR Speaker ~ ~ 16 pin 14 klue/lack (-) mplifier, left side of cargo area, behind wheel well LR Speaker ~ ~ 16 pin 07 Ltreen (+) mplifier, left side of cargo area, behind wheel well LR Speaker ~ ~ 16 pin 15 Ltreen/lack (-) mplifier, left side of cargo area, behind wheel well MPLIIER ONNETORS (WIRE SIE) 4 8 3 7 2 6 1 5 8 7 6 5 4 16 15 14 13 12 11 3 2 1 10 9 maestro.idatalink.com 7