instruction rev /13/2012

Transcription

1 INSTRUMENT LUSTER ISNET AESSORY NETOR INITION Sheet 2 FLOOR IMMER WIPER PA AS ROUN LEFT AN RIT AN ELETRI SPEEO ROUN ORN RELAY TURN SINAL PARIN BRAE NEUTRAL SAFETY EALIT BRAE RAIO IARETTE LITER BA UP INSTALLIN TE FUSE BOX 1. Locate the stock OEM bulkhead hole in the driver side of the firewall. 2. Mount the fuse box with the flasher can in the bottom right corner, as shown above. 3. Using the two mounting screws A, attached the fuse panel to the firewall. A A stock bulkhead connector hole Fuse Panel Installation Instructions Following these simple instructions will guarantee a successful installation of your American Autowire fuse panel harness. 1. Study the diagram above to familiarize yourself with the dash harness. 2. Install the fuse box. 3. Route the dash harness using the factory support straps. 4. Make all connections, as shown, on the following pages of this dash harness kit. 5. Once this harness is installed, continue to '', and install the rest of the kit (s,j,,l,m) AS IT stock fuse box mounting holes sheet instruction rev /13/2012

2 1 3 INITION FLOOR IMMER PA 6 BA UP 1. INITION 2. TURN SINAL This harness is set up with a 15 and later 4-1/4 turn signal connector and will mate directly to steering columns that utilize this connector. If you are using a pre 15 or aftermarket column that utilizes the 3-7/ connector, you can either remove the terminals from that connector and install connector A, on Sheet 5, or cut the connector off and crimp the supplied terminals onto the wires from your switch. Install the terminals into connector A, maintaining color continuity with the new switch. (see iagram "A" on Sheet 5 for this application) 12 volt battery feed 12 volt ignition feed 12 volt accessory feed 12 volt starter feed ark reen ark Blue ORN RELAY 5 NEUTRAL SAFETY TURN SINAL see iagram A on Sheet FLOOR IMMER 4. NEUTRAL SAFETY 5. BA UP 6. ORN RELAY 12 volt feed from brake switch R tail lamp L tail lamp 12 volt feed from turn flasher 12 volt feed from hazard flasher R front park lamp L front park lamp orn relay ground wire to horn switch Plug this connector into the floor dimmer switch (part # ). immer feed To IMMER FEE location on headlight switch. Light reen eadlight igh Beam Feed 'EALIT - I BEAM' from dimmer switch through the bulkhead connector to the front headlight connector high beam location. eadlight igh Low Feed 'EALIT - LOW BEAM' from dimmer switch through the bulkhead connector to the front headlight connector low beam location. onnect these wires to the neutral safety switch on the column, console shifter, or clutch switch. 12 volt feed 'in' to neutral safety switch. 12 volt feed 'out' to starter Lt reen onnect these wires to the back up switch on the column, console shifter, or transmission. 12 volt ignition feed 'in' to back up lamp switch 12 volt feed 'out' to back up lamps Plug the horn relay (found in the fuse ) into this connector. 12 volt battery Relay ground circuit (to steering column) reen Triggered 12 volts to horn AS IT 0196 instruction rev /13/2012

3 7 11 AESSORY NETOR INSTRUMENT LUSTER ISNET 12 WIPER See iagram B on Sheet 5 PA LEFT AN AS ROUN 10 PARIN BRAE EALIT Use the provided connector J attached and terminals as power leads for the following: Fuse Rating ark Blue FUEL 15 amp Fused 12 volt INITION feed for fuel pump (may also be used to feed power to another ignition circuit) BAT1 20 amp Fused 12 volt BATTERY feed for power seats (may also be used to feed power to another battery circuit) BAT2 30 amp Fused 12 volt BATTERY feed for power door locks (may also be used to feed power to another battery circuit) IN1 20 amp Fused 12 volt INITION feed for cruise control (may also be used to feed power to another ignition circuit) PWRWO 30 amp Fused 12 volt INITION feed for power windows (may also be used to feed power to another ignition circuit) AY1 30 amp Fused 12 volt AESSORY feed (may also be used to feed power to an accessory circuit). L 9. PARIN BRAE ELETRI SPEEO ROUN INSTRUMENT LUSTER ISNETS onnect to parking brake light switch onnect to a good chassis ground 12. WIPER See iangram B on Sheet 5 for connection details. Low speed ground igh speed ground ark Blue Washer pump ground Washer pump ground /Blue stripe (ROUN) round 12 volt lamp feed ray 13. EALIT k reen 12 volt feed to switch ray Radio accessory feed. (On-Off switch) Radio 12 volt clock lead (battery feed) Radio ground ash lights (typically dims the display on aftermarket radios when lights are turned on) AESSORY NETOR RAIO RAIO 14 Plug this connector into the mating connector from the courtesy lamp kit N, volt battery feed for lamp round circuit for lamp These connectors will plug into the gauge disconnect harness from. Wire identifications are described on the instruction sheets from. immer feed Instrument lamp feed ome / courtesy ground BAT location on headlight switch PAR / TAIL FEE IN location on headlight switch. (commonly found on M headlight switches) PAR OUT location on headlight switch. IMMER FEE location on headlight switch. INSTRUMENT location on headlight switch. ROUN location on headlight switch AS IT 0196 instruction rev /13/2012

4 PA 1 AS ROUN 20 RIT AN BRAE BRAE 17 IARETTE LITER 19 Plug this connector into the factory brake switch. 12 volt feed 'in' to switch. 12 volt feed 'out' to steering column turn signal switch. Lt Blue 12 volt feed 'out' to third brake light. 16. AAW has provided the heater or A/ feed wire only for this application to be used in conjunction with your OE factory heater or A/ harness. The mating connector and terminals for the connection located in the loose piece kit of the dash harness. If you desire a new heater or A/ harness for your truck, contact AAW for the exact application for your truck. (The orange A/ high speed blower power feed from your OE A/ harness can be plugged into the accessory plug #7, as shown on by removing the black connector from the wire and installing the bare terminal into the mating cavity of the RE wire at that accessory plug). 12 volt accessory feed to heater / A/ switch. (if using aftermarket A/, use this brown wire as the keyed accessory feed wire to a/c harness.) 17. ray orrect lamp socket for factory heater lamp is on the harness, plug this into the original location. Lamp ground. 1. ROUN onnect to a good chassis ground. 19. IARETTE LITER onnect to lighter. (battery feed) 20. R Plug this connector into the mating connector from the courtesy lamp kit N, volt battery feed for lamp round circuit for lamp AS IT 0196 instruction rev /13/2012

5 12 WIPER PA IARAM - B 13-2 Wiper switch connections Plug connector into the disconnect on the main dash harness (number 12 shown above). Route the three wires to the wiper switch and cut to length. Install terminal onto the wires and insert into connector E. 1-2 Plug connector into the disconnect on the main dash harness (number 12 shown above). Route the three wires to the wiper switch and cut to length. Install terminal onto the wires and insert into connector F. Insert the loose black (ROUN) and gray (AS LITS) wires into connector. Route the black wire (ROUN) to the switch and cut to length, double the cut off portion in terminal and insert into connector F. Route the other end of the black wire (ROUN) to the wiper switch lamp and cut to length, install terminal. Route the gray wire (AS LITS) to the wiper switch lamp and cut to length, install terminal, then insert both the gray and black wires into lamp socket J These connectors, wires, and terminals can be found with the dash harness in Bag WIPER NETIONS Plug connector into the disconnect on the main dash harness (number 12 shown above). Insert the loose black (ROUN), gray (AS LITS), and black / lt. blue wires into connector.route the six wires to the wiper switch and cut to length. Install terminal onto the wires and insert into an ORIINAL NETOR, we are unable to provide this connector in this kit TURN SINAL E The main dash harness comes with a 4-1/4 M turn signal switch connector found on 17 and later trucks (number 2 shown above). For steering columns that already have a 4-1/4 connector you can simply connect the column connector to the dash connector making sure color continuity is maintained. If you need to change the steering column connector you can either remove the terminals from the original connector and insert them into the supplied column connecter A. Or you can cut the wires and install the supplied terminal B and then insert into connector A. AMERIAN AUTOWIRE E F 13-2 dk blue lt blue black AS IT B A B lt blue black J dk blue white dark green yellow purple brown J L M N P AS ARNESS NETION white dk green yellow purple brown ORIINAL TURN SINAL WIRES A Low speed ground igh speed ground Washer ground ash lights 12 volt Wiper Park ground Switch ground / lamp ground ABEF F ark Blue ray / Lt. Blue (ROUN) escription ircuit number onnector not provided, must reuse original connector. IARAM - A 13-2 Steering olumn connections olor 1-2 J WIPER IRUIT NUMBERS AN ESRIPTIONS 0196 instruction rev /13/2012 sheet 5