INSTALLATION INSTRUCTIONS FOR PART B APPLICATIONS. Mazda CX

Transcription

1 INSTLLTION INSTRUTIONS FOR PRT PPLITIONS Mazda X KIT FETURES DIN Head Unit Provision with Pocket ISO DIN Head Unit Provision with Pocket Double DIN Head Unit Provision ISO Stacked Head Unit Provision Painted matte black to match factory KIT OMPONENTS ) Radio Housing ) ISO rackets ) ISO Trim Plate D) Double DIN rackets E) Double DIN Trim Plate F) Pocket D E F WIRING ND NTENN ONNETIONS (Sold Separately) MZTO-0 - Mazda mp Integration Harness 2007-Up T - Mazda service harness 2007-up TOOLS REQUIRED: Small Flat lade Screwdriver/ Panel Removal Tool Phillips Screwdriver OPYRIGHT METR ELETRONIS ORPORTION

2 TLE OF ONTENTS Dash Disassembly - Mazda X Kit ssembly - DIN Head Unit Provisions with Pocket ISO DIN Head Unit Provisions with Pocket Double DIN Head Unit Provision/Stacked ISO DIN Head Unit Provision..4 *Note: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto or call for more information and take steps toward a better tomorrow.

3 VOL POWER TUNE UDIO LOD/ INFO SEEK TRK UTO ON FRONT LO OFF HI DUL PSS RER MODE OUTSIDE TEMP / MP VOIE RETURN VOL POWER LOD/ SEEK TRK SOURE SN VOL POWER LOD/ SEEK TRK SOURE SN UTO ON UTO ON FRONT LO OFF HI OUTSIDE MODE RER TEMP FRONT OFF / DUL PSS TUNE UDIO INFO MP VOIE RETURN MENU DISP DUL PSS TUNE UDIO INFO MP VOIE RETURN MENU DISP DSH DISSSEMLY MZD X Disconnect the negative battery terminal to prevent an accidental short circuit. 73 0FMch Unclip and remove both side panels from center radio trim panel. (Figure ) 3 Unclip and remove the shifter trim panel. (Figure ) 73 0FMch Remove () Phillips screw from the accessory socket trim panel then unclip and remove the panel. (Figure ) P R N M D 5 Remove (2) Phillips screws from the radio trim panel. (Figure D) LO HI / 6 Unclip and remove the entire radio trim panel including the a/c controls. (Figure D) OUTSIDE MODE RER TEMP M P R N D 73 0FMch Remove (4) Phillips screws securing the radio. ontinue to kit assembly. VOL POWER LOD/ TUNE UDIO INFO E SEEK TRK SOURE MP VOIE RETURN MENU SN DISP UTO ON FRONT LO OFF HI DUL 73 0FMch / PSS OUTSIDE MODE RER TEMP

4 KIT SSEMLY DIN HED UNIT PROVISION WITH POKET *Note: Refer also to the instructions included with the aftermarket radio. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or XXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure ) 3 Snap the pocket into the bottom opening of the radio housing. (Figure ) 4 Slide the aftermarket head unit into the cage and secure. (Figure ) 5 Reassemble dash in reverse order of disassembly. 2

5 KIT SSEMLY ISO DIN HED UNIT PROVISION WITH POKET *Note: Refer also to the instructions included with the aftermarket radio. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or XXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Mount the ISO rackets to the head unit with the screws supplied with the unit. (Figure ) 3 Snap the pocket into the bottom opening of the radio housing.(figure ) 4 Slide the head unit into the radio opening until the side clips engage. (Figure ) 5 Snap the Trim plate into the Radio Housing. (Figure ) 6 Reassemble dash in reverse order of disassembly. 3

6 KIT SSEMLY DOULE DIN HED UNIT PROVISION/ STKED ISO DIN HED UNIT PROVISION *Note: Refer also to the instructions included with the aftermarket radio. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or XXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 ut and remove the center bar from the radio housing. (Figure ) 3 Snap the Double DIN brackets to the inside edge of the Double DIN trim plate. (Figure ) 4 Slide the Double DIN head unit or stacked ISO head units into the bracket/radio housing assembly and secure the Double DIN head unit or stacked ISO head units to the assembly using the screws supplied with the radio. (Figure ) 5 Snap the double DIN trim plate into the radio housing. (Figure ) 6 Reassemble dash in reverse order of disassembly. 4

7 NOTES 5

8 INSTRUTIONS REV. 04/2/0 OPYRIGHT METR ELETRONIS ORPORTION INST99-756