GEN 5 LOCKPICK INSTALLATION POSSIBILITIES

Transcription

1 EVEN IF YOU ALREADY HAVE A FACTORY REAR VIEW CAMERA THE GEN 5 MAKES IT EASY TO ADD A FRONT OR BABY CAM ** INCLUDED CONNECTION FOR AFTERMARKET CAMERA(S) OR ANY STANDARD VIDEO INPUT IF REAR CAMERA, CONNECT POWER TO GEN 5 REVERSE POWER OUT IF FRONT/BABY CAMERA, CONNECT POWER TO GEN 5 ACC POWER OUT AFTERMARKET REAR/FRONT OR BABY CAMERA CONNECT FRONT/BABY CAM POWER TO GEN 5 ACC POWER OUT FRONT/BABY CAMERA UNPLUG ORIGINAL CONNECTORS THEN PLUG IN HERE IF THE VEHICLE IS NOT EQUIPPED WITH A FACTORY REAR VIEW CAMERA CONNECT THE AFTERMARKET CAMERA AS SHOWN AFTERMARKET REAR CAMERA CONNECT REAR POWER TO GEN 5 REVERSE POWER OUT THE GEN 5 SUPPORTS MULTIPLE AFTERMARKET CAMERAS IF DESIRED OR CONNECT VIDEO FROM YOUR IPOD, DVD, GAME, SAT TV, ETC. GEN 5 CONNECTORS PLUG INTO RADIO GROUND TO ALL CAMERAS GEN 5 LOCKPICK INSTALLATION POSSIBILITIES CONSTANT POWER OUTPUT ACC POWER TO FRONT/BABY CAMERA PROGRAMMING DIP SWITCHES FOR FULL CONTROL OF YOUR FACTORY REAR CAMERA, EVEN WHILE IN DRIVE, CONNECT THIS BLUE WIRE AS INSTRUCTED IN YOUR INSTALATION MANUAL FOR AFTARMARKET REAR CAM INSTALLATIONS, USE THIS WIRE FOR YOUR REAR CAMERA 12V POWER NEEDS

2 Coastal Electronic Technologies, Inc. GM LOCKPICK GEN 5 NOTE: THESE INSTRUCTIONS ARE UPDATED FOR THE GEN 5 OVERRIDE OPERATIONS AND SWITCH SETTINGS HAVE CHANGED Installation Instructions Thank you for your purchase of the Coastal Electronic Technologies, Inc. GM LOCKPICK GEN 5. After installation, the GEN 5 will allow continuous operation of the AUX input video features of your navigation screen (vehicle must have a VIDEO AUX input jack in the console - small audio jack in front of screen is not a video AUX input), and if your screen is capable of playing DVD movies, the GEN 5 LOCKPICK will allow continuous operation of the DVD player when selected. The GEN 5 is equipped with a video input that you can use for a rear camera input, a front camera input or both. The video input can also be used for displaying the picture from your ipod, video game, computer or external DVD player. (See below for video input programming requirements) The GEN 5 LOCKPICK will also allow the user to unblock on command, navigation features locked when in motion and various functions locked in XM and CD player modes. This includes address entry and points of interest searching, along with radio controls for XM category, CD folders etc., all which are blocked while in motion. At this time, Coastal Electronic Technologies, Inc. would like to recommend that you have this installation completed by a certified mechanic or someone familiar with automotive electronics. This installation, while not time consuming, does require careful attention to detail and precise following of installation instructions. Coastal Electronic Technologies, Inc. accepts no responsibility due to the improper installation or use of this product. Please adhere to all driving laws in your state. Installation and / or use of this product implies and signifies user acceptance of this term of use. Installation Start with the car and radio turned off. The GEN 5 is designed with a dual T harness, equipped with factory male and female connectors for direct connections to your screen. With access to the rear of the screen, unplug the matching Black and Brown connectors and plug them into the female connectors of your LOCKPICK. Then plug the male connectors of the LOCKPICK harness into the earlier factory locations. The connectors are keyed and cannot be plugged in to the wrong location. Slide the blue locking tabs on the top of the connectors back before attempting to insert the plug fully into the radio. Next, determine the switch setting you desire for your installation. There are several modes of operation available for your GEN 5 depending on the vehicle year, options and required functions. Examples of each are explained and demonstrated in this document. For most installations, the disassembly needed to get to the rear of the screen will consist of popping loose the trim around the face of the radio to expose the 7mm or 10mm bolts holding the radio in position. Remove the bolts and the radio can be tilted rearward to view the connectors needed. The trim around the face of the radio is held in place with spring loaded friction locks which sometimes can require extra pressure to release. Videos and photos have been provided on the CoastalEtech.com website to provide you assistance. Installation process for standard GM vehicles is available at Cadillac Escalade installation is provided at Video unblocking operations can be viewed at NAV and radio unblocking operations can be viewed at Rear view camera programming procedures can be viewed at Quick Install Checklist: Remove radio trim and unbolt radio Plug in black and brown connectors supplied to matching connectors in back of radio Plug in aftermarket video if desired Set dip switches on Lockpick. Note: Lockpick must be unplugged to alter switch settings. Plug Lockpick into harness and test DVD/AUX and/or EXT video with vehicle in DRIVE only 1. Press mute 4x to unlock video some vehicles do not require a button press 2. Press mute 2x to unlock nav and xm blocks automatically times out after 60 seconds 3. Press window lockout 4x to GEN 5 Video input (requires factory camera or camera programming - ) 4. Press mute 2x to end any function immediately two audible beeps will be heard

3 Included in your GM LOCKPICK harnesses are easy connections for: 1. Constant battery 12V power (YELLOW) 2. Ground (GRAY) 3. ****STANDARD RCA video connection**** - An important feature of your LOCPICK is the ability to easily input video from additional video sources (rear, front, baby cam, DVD, video ipod, ZUNE, etc. or as a video input for vehicles not equipped with factory DVD play or video AUX input capability) This input is dependent upon the presence of a factory rear view camera or, the option for factory rear view camera can easily be turned on at your dealership. If your vehicle is not equipped with a factory rear view camera and you desire to use the video input provided by the LOCKPICK harness, programming instruction for your dealer are available at as an example. If you have the factory camera programming enabled, but do not plan to use a rear view camera, the GEN 5 LOCKPICK can prevent the screen from blanking during reverse operation. Set dip switch 3 DOWN for NO REAR VIEW CAMERA PRESENT and your screen will not blank during reverse, even if it has been updated for reverse camera operation. This allows you to use the video source provided by the LOCKPICK for other purposes and not have the screen search for a rear view camera during reverse. If you have a factory camera or will be adding an aftermarket reverse camera, place switch 3 in the UP position to allow the screen to automatically switch to rear camera view while in reverse. 4. Accessory ignition Switched 12V power (RED) The switched ignition 12V source (ACC) RED wire, will turn off when the car is turned off. This is useful to allow the installation of aftermarket cameras, DVD players, radar detector, etc. without worrying that they may run down the vehicle battery when the car is turned off. It may also be connected to your aftermarket Bluetooth kit as an accessory power connection. This output is capable of 2.5 amps. Aftermarket FRONT or BABY view cameras should be powered by the (ACC) RED wire. NOTE: The 12V output from the GEN 5 ACC wire will turn off while the vehicle is in REVERSE gear and for approximately 12 seconds after shifting out of Reverse gear. This is to allow simultaneous use of multiple video inputs without conflict of video signals.. 5. Reverse camera power 12V (BLUE) The Blue reverse camera wire in you GEN 5 harness is designed to power your aftermarket rear view camera or to allow you full on-demand control of your factory rear view camera. **** NOTE: To install the GEN 5 Lockpick and control a FACTORY REAR VIEW CAMERA for use while in DRIVE, etc. the BLUE Reverse camera power must be connected as the power source for your factory camera which is only powered during Reverse. This is a relatively simple procedure in most vehicles and is detailed in step 6 of this instruction set. This is only necessary if you want to be able to view your factory camera while in DRIVE and not required for installation of the Lockpick in factory camera equipped applications **** NOTE: Do not connect the wires for power, ground or accessory power to the wiring of your car (the unit is full plug and play for DVD, AUX, and NAV unblock). These outputs are provided as a BONUS to save you time when connecting any additional accessories or video source. ***NOTE*** A. Set the switch setting desired before plugging the LOCKPICK box into the included harness. If you wish to change the switch setting after plugging in the controller, the car and radio must be off, and the box unplugged first. Then change the switch setting and plug it back in. B. If you wish to utilize the LOCKPICK supplied video connection, the vehicle must be equipped with a factory rear view camera, or have the rear view camera option enabled by your GM service center. This is a simple update procedure in non-equipped vehicles and will activate the video input provided by the LOCKPICK (See for example.) C. Vehicles manufactured AFTER 10/06 may require switch 1 to be in the down position. Vehicles manufactured BEFORE 10/06 may desire to place switch 1 down if desired for automatic unlock of DVD and AUX input jacks Most installations will require a button press ( MUTE or WINDOW LOCKOUT see operation instructions) for unlocking of particular functions. If your vehicle can operate with switch 1 UP and still unlock DVD video with the mute button pressed 4x, it is preferable to use this setting instead of the automatic setting of switch 1 DOWN. Switch 1 DOWN sets the LOCKPICK to suspend NAV map tracking while viewing DVD video in motion as is required for this series of radios. Switch 1 UP continues NAV map tracking even while the DVD is unlocked for viewing while in DRIVE. If your NAV address input screen is not unlocked or blinks after attempting to unlock it by pressing the mute button 2x, unplug the module and set switch 1 to the UP position. Your radio system uses this type of programming. Typically Cadillac Escalades will use the switch 1 UP setting as well as some non-dvd play capable radios in GMC and Buick models.

4 DVD/AUX/CAM LOCKPICK SWITCH SETTING MODES VIDEO/CAM INPUT REQUIRES FACTORY CAMERA OR CAMERA PROGRAMMING ENABLED BY DEALER 1. ADVANCED VIDEO UNLOCK SWITCH 1 DOWN IS REQUIRED SETTING FOR SOME VEHICLES MANUFACTURED AFTER 10/06 LOCKPICK WILL AUTOMATICALLY UNLOCK DVD AND AUX INPUT VIDEO WHILE STOPPED. TO ENABLE VIDEO WHILE MOVING, PRESS MUTE 4X VEHICLES MANUFACTURED BEFORE 10/06 THIS ADVANCED SETTING WILL AUTOMATICALLY UNBLOCK DVD AND AUX VIDEO IN MOTION WITHOUT BUTTON PRESSES 2. MANUAL OPERATION OF DVD/AUX JACK UNLOCK OPTIONAL SETTING FOR VEHICLES MANUFACTURED BEFORE 10/06 REQUIRED for full functioning in Escalades, and most non-dvd play capable GMC and BUICK radios REQUIRES USER PRESS MUTE 4X TO UNLOCK DVD OR FACTORY AUX INPUT AFTER VEHICLE IS PLACED IN DRIVE NOTE: PLACE SWITCH 3 DOWN IN ADDITION TO BLOCK THE RADIO FROM SWITCHING TO A REAR CAMERA VIEW WHEN THE CAR IS PLACED IN REVERSE. *This can allow the radio to be reflashed by the dealer for rear camera operation and the camera input to be use by the Lockpick and not have the picture blank when the car is put is Reverse. Do not place switch 3 down if you have a factory rear view camera or will be adding one. 6. If you would like to enable full control and viewing of your FACTORY REAR VIEW CAMERA when in DRIVE, attach the included FACTORY CAMERA OPTION wire to the 12V REVERSE wire labeled in your GEN 5 harness. A crimp connector is already attached for your convenience. Route the wire along the edge of the console and down to the small silver module under the passenger seat. Slide the seat all the way back to view the connector on the front or side edge. Unplug the connector and cut the Blue wire pictured in the photo below ( end wire, left side, from the back of the plug ). Crimp the Blue wire from your kit to the blue wire on the connector. The other cut end of the wire in the factory harness should be insulated and left disconnected. Do not connect the Lockpick Blue wire without cutting the factory wire or improper operation will occur. For 2008 H2 Hummer installations, run the GEN 5 Blue wire to the back of the vehicle and connect directly to the rear view camera connector blue wire. Refer to website at: for install pictures. Other vehicles (Enclave, Acadia) may place the module in the rear as well. Refer to website at: for installation help. For 2008 H2 and all 2009 vehicle installations, run the GMX-322 blue wire to the back of the vehicle and connect directly to the rear view camera connector blue wire. Refer to website at: for example install pictures. 6. OPTIONAL FACTORY CAMERA LOCKPICK CONNECTION DETAIL Unplug connector from module under passenger seat. Cut blue wire Attach Factory Camera Option Blue wire to blue wire of factory connector Crimp completed connection and plug connector back into module Cover remaining loose end of blue wire left in factory harness and leave disconnected Anytime factory camera use is now enabled by the GEN 5 Unplug connector from camera module under passenger seat and pull into view as shown. Cut and strip pictured blue wire as demonstrated and attach to wire included with your Lockpick.

5 GM LOCKPICK OPERATION INSTRUCTIONS The GM LOCKPICK will operate to unlock video on the front screen from your console video AUX input jack (small jack on front of radio is not a video input), or from the front factory DVD player if equipped. If your car does not have DVD play capability or AUX jacks, the LOCKPICK cannot create these functions for you. The navigation and radio restrictions for address entry, points of interest, XM categories, CD folder, etc. are easily unlocked using factory button presses. In addition, the LOCKPICK can turn on and control a separate video input which you can use for a rear view camera, front cam, baby cam, ipod, DVD etc. All functions are controlled with either the MUTE button on your steering wheel, the WINDOW LOCKOUT button on your door. After the Lockpick is installed in some vehicles, the DVD video may already be unlocked when you put the car is DRIVE, but then will reblock when the car begins moving. This is because you have not activated the Lockpick yet. To enable in motion video viewing for all applications, place the vehicle in DRIVE gear, then press the MUTE button on your steering wheel four (4) times within 6 seconds. You will hear an audible beep to let you know that you were successful. Once unblocked, video will be viewable on the front screen for the entire duration of your trip or until you turn the function OFF. To turn the video OFF and return to standard blocked operation, press the MUTE button 2 times. You will hear two audible beeps to let you know you have turned off the unlocking technology. The function will also automatically turn off if the car is turned off. It s as simple as that to have full control of the video on your front screen. The GM LOCKPICK will allow all other blocked functions of the navigation radio to be unlocked while in motion including address entry, points of interest, XM category scrolling, CD information etc. To enable any blocked nav/radio function, press the MUTE button two (2) times within 6 seconds and listen for an audible beep to let you know you were successful. For your convenience, the unlock function will automatically time out after approximately 60 seconds, or you may Press the MUTE button two (2) times again to immediately end the unlock. You will hear two audible beeps to let you know that you have successfully turned it off. SIMPLE OPERATION FOR YOUR GEN 5 LOCKPICK **WHILE IN DRIVE GEAR** (NOT IN PARK) PRESS MUTE BUTTON 4 TIMES TO UNLOCK AUX OR DVD VIDEO IN MOTION WHEN DESIRED PRESS MUTE 2 TIMES TO TURN ON NAV UNBLOCK - THIS WILL AUTOMATICALLY TIME OUT AFTER 60 SECONDS PRESS MUTE BUTTON 2 TIMES TO END ANY ACTIVE LOCKPICK FUNCTION **WHILE KEY IS FULLY ON** PRESS WINDOW LOCKOUT BUTTON 4 TIMES WHILE IN XM MODE TO TURN ON LOCKPICK FRONT, BABY OR OTHER (IPOD, DVD, GAME, ETC.) VIDEO INPUT PRESS 4X WHILE IN OTHER RADIO MODES (AM, FM, ETC) TO VIEW AFTERMARKET OR FACTORY REVERSE CAM PRESS WINDOW LOCKOUT 4 TIMES TO TURN OFF LOCKPICK VIDEO INPUT OR PRESS MUTE 2 TIMES

6 The GM LOCKPICK can turn on an additional video input to your front screen if desired and allow its viewing at any time. This can be used for camera input (rear, front, side, baby) or as an input for other video devices (video ipod, computer etc.). This function is only available to vehicles which have a rear view camera or the option enabled on their vehicle (this option can be added by your dealership within a few minutes if you don t have a camera). To turn on and activate the LOCKPICK video input for viewing on your front screen, press the WINDOW LOCKOUT button FOUR (4) times within 6 seconds. Just like that, the video from your connected device is viewable on your front screen. To turn it OFF, press the WINDOW LOCKOUT button four (4) times again or you can press the mute button 2 times. The Lockpick can also power and control multiple cameras if desired. Included in your wiring harness are connections for video input, REVERSE camera power and also FRONT/BABY cam power. If controlling a REVERSE camera, use the included REV power supplied by the Lockpick to allow automatic and anytime viewing of a backup camera. This is detailed in Step 6 of your installation instruction for factory camera control or connects directly as the power for your aftermarket camera if adding to a non equipped vehicle. To activate the rear view camera view and REVERSE power source, place the radio on AM, FM, etc. (anything but XM) and press the window lockout button 4x. This will power the rear camera and display it on your screen. It will also activate automatically when you put your car in reverse gear if desired (switch 3). The GEN 5 can also power and control a front/baby cam. Connect your alternate camera power needs to the ACC power connection on the Lockpick harness. Place the radio on the XM mode this time and perform the window button press (4x) to activate the Lockpick video input. This will activate the radio video input and apply power to the ACC power connection to allow anytime viewing of this video source. *Note The Lockpick will delay approximately 12 seconds after the vehicle has been placed in Reverse or the Rear camera has been activated manually before it will send power to the ACC power out connection. This is to allow for the factory camera in equipped vehicles to finish its view before powering a second camera. Using the Lockpick supplied video input to view a video source or camera on your front screen does not affect map tracking or any other function of your radio. NOTE: When the Lockpick has been activated to allow the operator to enter an address while in motion (MUTE 2x), the navigation map tracking is blocked momentarily to allow you the opportunity to fully use your system. When you finish inputting your information, it is recommended that you turn the NAV override function OFF manually by pressing again, the MUTE button 2x. This allows the navigation system to reposition you on the map (normally 3-7 seconds) and all functions operate as usual. The Lockpick will automatically time out and turn off after 1 minute even if you do not turn it off but, if you turn it off manually as recommended, it will decrease the amount of time needed to reposition again. Also, activating DVD and AUX input video viewing (MUTE 4x) on the front screen will block navigation map tracking while enabled on some vehicles. If your vehicle can allow DVD override with switch 1 is in the UP position, then map tracking is NOT affected while activating and viewing DVD/AUX video. If your vehicle requires advanced unlocking (switch 1 DOWN) to allow DVD Lockpick functions to operate, then map tracking is blocked while DVD viewing is enabled. To restore active map tracking, simply turn the DVD override function OFF by pressing the mute button 2x. The GM LOCKPICK is compatible with ONSTAR equipped vehicles without error and does not affect navigation systems when not being used. Enjoy your GEN 5 LOCKPICK!!